Safety Instructions . . . . . . . 2–4
Owner’s Manual
Operating Instructions
JP930
JP931
JP960
JP961
Bridge Surface Unit . . . . . . . . .6
Cookware Tips . . . . . . . . . . . .7, 8
Dual Surface Unit . . . . . . . . . . 6
Surface Units . . . . . . . . . . . . 5, 6
Temperature Limiter . . . . . . . . .6
Care and Cleaning
Control Knobs . . . . . . . . . . . . . 9
Glass Cooktop . . . . . . . . . . 10, 11
Troubleshooting Tips . . . . . . 12
Consumer Support
Consumer Support . . Back Cover
Product Registration . . . . . 13, 14
Warranty . . . . . . . . . . . . . . . . . 15
Write the model and serial
numbers here:
Model # ________________
Serial # ________________
You can find them on a label
under the cooktop.
164D4290P118 49-80161 09-02 JR
SAFETY PRECAUTIONS
I Do not touch surface units. These surfaces I Use little fat for effective shallow or
may be hot enough to burn even though
they are dark in color. During and after
use, do not touch, or let clothing or other
flammable materials contact the surface
units or areas nearby the surface units;
allow sufficient time for cooling first.
deep-fat frying. Filling the pan too full
of fat can cause spillovers when food is
added.
I If a combination of oils or fats will be used
in frying, stir together before heating, or as
fats melt slowly.
I Potentially hot surfaces include the
I Always heat fat slowly, and watch as it heats.
cooktop and areas facing the cooktop.
I Use a deep fat thermometer whenever
possible to prevent overheating fat beyond
the smoking point.
I To minimize the possibility of burns,
ignition of flammable materials and
spillage, the handle of a container
should be turned toward the center
of the cooktop without extending over
any nearby surface units.
I Never try to move a pan of hot fat,
especially a deep fat fryer. Wait until
the fat is cool.
I Always turn the surface unit control to off
I Do not store flammable materials near
before removing the cookware.
the cooktop.
I Use proper pan size—select cookware
having flat bottoms large enough to cover
the surface unit heating element. The use
of undersized cookware will expose a
portion of the surface unit to direct
I Keep the hood and grease filters clean
to maintain good venting and to avoid
grease fires.
I Do not store or use combustible materials,
gasoline or other flammable vapors and
liquids in the vicinity of this or any
appliance.
contact and may result in ignition of
clothing. Proper relationship of cookware
to surface unit will also improve efficiency.
I Clean only parts listed in this Owner’s
I Never leave surface units unattended at
Manual.
high heat settings. Boilovers cause smoking
and greasy spillovers that may catch on fire. I Do not leave paper products, cooking
utensils or food on the cooktop when
I Only certain types of glass, glass/ceramic,
not in use.
earthenware or other glazed containers are
suitable for cooktop cooking; others may
break because of the sudden change in
temperature.
I Keep cooktop clean and free of
accumulation of grease or spillovers
which may ignite.
I Keep an eye on foods being fried at high
I Never heat unopened food containers.
Pressure buildup may make container
burst and cause injury.
or medium-high heat settings.
I Foods for frying should be as dry as
possible. Frost on frozen foods or moisture I Never leave jars or cans of fat drippings
on fresh foods can cause hot fat to bubble
up and over the sides of the pan.
on or near your cooktop.
I Never use your appliance for warming or
heating the room.
COOK MEAT AND POULTRY THOROUGHLY…
Cook meat and poultry thoroughly—meat to at least an INTERNAL temperature of 160°F and poultry
to at least an INTERNAL temperature of 180°F. Cooking to these temperatures usually protects against
foodborne illness.
3
IMPORTANT SAFETY INFORMATION.
READ ALL INSTRUCTIONS BEFORE USING.
WARNING!
RADIANT SURFACE UNITS
Use care when touching the cooktop. The glass surface of the cooktop will retain heat after the
controls have been turned off.
I Avoid scratching the glass cooktop.
The cooktop can be scratched with items
such as sharp instruments, rings or other
jewelry and rivets on clothing.
I Clean the cooktop with caution. If a wet
sponge or cloth is used to wipe spills on
a hot surface unit, be careful to avoid
steam burns. Some cleansers can produce
noxious fumes if applied to a hot surface.
I Never use the glass cooktop surface as
a cutting board.
I NOTE: We recommend that you avoid
wiping any surface unit areas until they
have cooled and the indicator light has
gone off. Sugar spills are the exception
to this. Please see the Cleaning the Glass
Cooktop section.
I Do not place or store items on top of the
glass cooktop surface when it is not in use.
I Be careful when placing spoons or other
stirring utensils on glass cooktop surface
when it is in use. They may become hot
and could cause burns.
I When the cooktop is cool, use only
CERAMA BRYTE® Ceramic Cooktop
Cleaner and the CERAMA BRYTE®
Cleaning Pad to clean the cooktop.
I Avoid heating an empty pan. Doing so may
damage the cooktop and the pan.
I Do not allow water, other liquids or grease
I To avoid possible damage to the cooking
surface, do not apply the cleaning cream
to the glass surface when it is hot.
to remain on the cooktop.
I To minimize the possibility of burns, always
be certain that the controls for all surface
units are at the off position and the entire
glass surface is cool before attempting to
clean the cooktop.
I After cleaning, use a dry cloth or paper
towel to remove all the cleaning cream
residue.
I Read and follow all instructions and
I Do not operate the glass surface units if
the glass is broken. Spillovers or cleaning
solution may penetrate a broken cooktop
and create a risk of electrical shock.
warnings on the cleaning cream labels.
I Use care when touching the cooktop. The
glass surface of the cooktop will retain heat
after the controls have been turned OFF.
Contact a qualified technician immediately
should your glass cooktop become broken. I Do not stand on the glass cooktop.
I Large scratches or impacts to glass
cooktops can lead to broken or
shattered glass.
READ AND FOLLOW THIS SAFETY INFORMATION CAREFULLY.
SAVE THESE INSTRUCTIONS
4
Using the surface units.
Throughout this manual, features and appearance may vary from your model.
How to Set
Push the knob in and turn in either
direction to the setting you want.
The UNIT ON indicator light will glow
when any surface unit is on.
At both OFF and HI the control clicks
into position. You may hear slight
clicking sounds during cooking,
indicating the control is keeping the
power level you set.
A HOT SURFACE indicator light will glow
when any radiant element is turned on
and will remain on until the surface is
cooled to approximately 150°F.
Be sure you turn the control knob
to OFF when you finish cooking.
NOTE:
The controls for the radiant surface units
can be set anywhere between LO and HI
for an unlimited number of heat settings.
With the infinite switch the unit cycles
on and off to maintain your selected
control setting.
IIt comes on when the unit is hot to the touch.
IIt stays on even after the unit is turned off.
IIt glows brightly until the unit is cooled to
approximately 150°F.
The control must be pushed in to set
only from the OFF position. When the
control is in any position other than OFF,
it may be rotated without pushing it in.
About the radiant surface units…
The radiant cooktop features heating
units beneath a smooth glass surface.
SURFACE
COOKING
IWater stains (mineral deposits) are removable
using the cleaning cream or full strength white
vinegar.
NOTE: A slight odor is normal when a new
cooktop is used for the first time. It is caused by
the heating of new parts and insulating materials
and will disappear in a short time.
IUse of window cleaner may leave an
iridescent film on the cooktop. The cleaning
cream will remove this discoloration.
Never cook directly on the glass.
Always use cookware.
NOTE: On models with light colored glass
cooktops, it is normal for the cooking zones to
change color when hot or cooling down. This is
temporary and will disappear as glass cools to
room temperature.
IDon’t store heavy items above the cooktop.
If they drop onto the cooktop, they can cause
damage.
OFF CENTER
IDo not use the surface as a cutting board.
The surface unit will cycle on and off to
maintain your selected control setting.
It is safe to place hot cookware from the
oven or surface on the glass cooktop
when the surface is cool.
Always place the pan in the center of
the surface unit you are cooking on.
Even after the surface units are turned
off, the glass cooktop retains enough
heat to continue cooking. To avoid
overcooking, remove pans from the
surface units when the food is cooked.
Avoid placing anything on the surface
unit until it has cooled completely.
DRAGGING
Do not slide cookware across the
cooktop because it can scratch the
glass. The glass is scratch-resistant,
not scratchproof.
5
Using the surface units.
Dual Surface Unit (on some models)
Large 9"
surface unit
setting
To use the small (6-inch) surface
unit, turn the SELECTOR knob
counterclockwise to . Push in and
turn the control knob to the desired
setting. The unit will only heat the area
inside the smaller circle.
The right front surface unit has 2 cooking sizes to
select from so you can match the size of the unit
to the size of the cookware you are using.
Small 6"
surface unit
setting
To use the large (9-inch) surface unit,
turn the SELECTOR knob clockwise to
.
Push in and turn the control knob to the
desired setting. The unit will heat the
entire area contained by the larger circle.
Bridge Surface Unit (on some models)
Choose pans that match the
circle/bridge area as closely as possible.
You can create an oblong heated area by using
the left rear unit in addition to the front unit
bridge combination.
When the select knob points to
the control knob controls the left front
surface unit only.
,
Make sure the pan rests flat on the glass
cooktop.
When the select knob points to
,
the control knob controls both the left
front surface unit and the bridge area.
Temperature Limiter
Every radiant surface unit has a
temperature limiter.
The temperature limiter may cycle the
units off for a time if:
I The cooktop is on while cooking.
I The pan boils dry.
The temperature limiter protects the
glass cooktop from getting too hot.
I The pan bottom is not flat.
I The pan is off-center.
I There is no pan on the unit.
6
Selecting types of cookware.
The following information will help you choose cookware which will give good performance on glass cooktops.
Stainless Steel:
recommended
Porcelain Enamel-Covered Cast Iron:
recommended
As long as the cookware is covered
completely with porcelain enamel, this
cookware is recommended. Caution is
recommended for cast-iron cookware
that is not completely covered with
smooth porcelain enamel, since it may
scratch the glass ceramic cooktop.
Aluminum:
heavyweight recommended
Check pans for flat bottoms by
using a straight edge.
Good conductivity. Aluminum residues
sometimes appear as scratches on the
cooktop but can be removed if cleaned
immediately. Because of its low melting
point, thin weight aluminum should not
be used.
Glass-Ceramic:
usable, but not recommended
Poor performance. May scratch the
surface.
Copper Bottom:
recommended
Copper may leave residues which can
appear as scratches. The residues can
be removed, as long as the cooktop is
cleaned immediately. However, do not let
these pots boil dry. Overheated metal can
bond to glass cooktops. An overheated
copper-bottom pot will leave a residue
that will permanently stain the cooktop
if not removed immediately.
Stoneware:
usable, but not recommended
Poor performance. May scratch the
surface.
Use pans that match the diameter of the
surface unit. Cooking performance will
not be as good if the cookware is either
smaller or larger than the surface unit.
Pans with rounded, curved, ridged
or warped bottoms are not
recommended.
For Best Results
I Place only dry pans on the surface
units. Do not place lids on the surface
units, particularly wet lids.
I Some special cooking procedures
require specific cookware such as
pressure cookers, deep fat fryers, etc.
All cookware must have flat bottoms
and be the correct size.
I Do not use woks that have support
rings. This type of wok will not heat on
glass surface units.
Do not place wet pans
on the glass cooktop.
I We recommend that you use only a
flat-bottomed wok. They are available
at your local retail store. The bottom
of the wok should have the same
diameter as the surface unit to ensure
proper contact.
Do not use woks with support
rings on the glass cooktop.
Use flat-bottomed woks
on the glass cooktop.
7
Selecting types of cookware.
Observe the Following Points in Canning
Remember that canning is a
process that generates large
amounts of steam. To avoid burns
from steam or heat, be careful
when canning.
Pots that extend beyond 1″ of the
surface unit’s circle are not
recommended for most surface
cooking. However, when canning with
water-bath or pressure canner, larger-
diameter pots may be used. This is
because boiling water temperatures
(even under pressure) are not harmful
to the cooktop surfaces surrounding the
surface units.
Right!
NOTE: If your house has low voltage,
canning may take longer than expected,
even though directions have been carefully
followed. The process time will be
shortened by:
Wrong!
Note: Flat-bottomed canners are
required for glass cooktops.
HOWEVER, DO NOT USE LARGE-
DIAMETER CANNERS OR OTHER
LARGE-DIAMETER POTS FOR
FRYING OR BOILING FOODS OTHER
THAN WATER. Most syrup or sauce
mixtures—and all types of frying—cook
at temperatures much higher than
boiling water. Such temperatures could
eventually harm the glass cooktop
surfaces.
(1) using a pressure canner, and
(2) starting with HOT tap water for fastest
heating of large quantities of water.
CAUTION:
I Safe canning requires that harmful
microorganisms are destroyed and that
the jars are sealed completely. When
canning foods in a water-bath canner,
a gentle but steady boil must be
maintained for the required time. When
canning foods in a pressure canner, the
pressure must be maintained for the
required time.
Be sure the canner fits over the
center of the surface unit. If your
cooktop or its location does not
allow the canner to be centered
on the surface unit, use smaller
diameter pots for good canning
results.
I After you have adjusted the controls,
it is very important to make sure the
prescribed boil or pressure levels are
maintained for the required time.
Flat-bottomed canners must be
used. Do not use canners with
flanged or rippled bottoms (often
found in enamelware) because
they don’t make enough contact
with the surface units and take a
long time to boil water.
I Since you must make sure to process the
canning jars for the prescribed time, with
no interruption in processing time, do not
can on any cooktop surface unit if your
canner is not flat.
When canning, use recipes and
procedures from reputable sources.
Reliable recipes and procedures
are available from the
manufacturer of your canner;
manufacturers of glass jars for
canning, such as Ball and Kerr
brand; and the United States
Department of Agriculture
Extension Service.
8
Care and cleaning of the cooktop.
Be sure electrical power is off and all surfaces are cool before cleaning any part of the cooktop.
How to Remove Packaging Tape
To assure no damage is done to the finish Apply with a soft cloth and allow to soak.
of the product, the safest way to remove
the adhesive left from packaging tape,
cooktop labels on the new appliances
is an application of a household liquid
dishwashing detergent, mineral oil or
cooking oil.
Wipe dry and then apply an appliance
polish to thoroughly clean and protect
the surface.
NOTE: The adhesive must be removed from all
parts. It cannot be removed if it is baked on.
Control Knobs
Molded rib
Stem
Wash knobs in soap and water but do not
soak. Avoid getting water down into the
knob stem holes.
The control knobs may be removed for easier
cleaning.
Spring
clip
Before removing the knobs for cleaning,
please note that the knobs are in the
OFF position. When replacing the knobs,
check the OFF position to ensure proper
placement.
The stem has a groove in each side. The
groove on one side has a spring clip. The
other groove is clear. Check the inside of
the knob and find the molded rib.
Clear groove
Replace the knob by fitting the molded
rib inside the knob into the clear groove
on the stem.
9
Cleaning the glass cooktop.
Normal Daily Use Cleaning
ONLY use CERAMA BRYTE® Ceramic
Cooktop Cleaner on the glass cooktop.
Other creams may not be as effective.
Shake the cleaning cream well.
Apply a few drops of CERAMA
BRYTE® Ceramic Cooktop Cleaner
directly to the cooktop.
To maintain and protect the surface of
your glass cooktop, follow these steps:
Use a paper towel or CERAMA
BRYTE® Cleaning Pad for Ceramic
Cooktops to clean the entire
cooktop surface.
Before using the cooktop for the
first time, clean it with CERAMA
BRYTE® Ceramic Cooktop Cleaner.
This helps protect the top and
makes cleanup easier.
Use a dry cloth or paper towel
to remove all cleaning residue.
No need to rinse.
Clean your cooktop after
each spill. Use CERAMA
BRYTE® Ceramic Cooktop
Cleaner.
Daily use of CERAMA BRYTE®
Ceramic Cooktop Cleaner will help
keep the cooktop looking new.
NOTE: It is very important that you DO NOT
heat the cooktop until it has been cleaned
thoroughly.
Burned-On Residue
If any residue remains, repeat the
steps listed above as needed.
WARNING: DAMAGE to your glass surface
may occur if you use scrub pads other than the
pad included with your cooktop.
For additional protection, after all
residue has been removed, polish
the entire surface with CERAMA
BRYTE® Ceramic Cooktop Cleaner
and a paper towel.
Allow the cooktop to cool.
Spread a few drops of CERAMA
BRYTE® Ceramic Cooktop Cleaner
on the entire burned residue area.
Use a CERAMA BRYTE® Cleaning
Pad for Ceramic Cooktops or a
Scotch-Brite® Multi-Purpose No
Scratch blue scrub pad.
Using the included CERAMA
BRYTE® Cleaning Pad for Ceramic
Cooktops, rub the residue area,
applying pressure as needed.
Heavy, Burned-On Residue
Allow the cooktop to cool.
For additional protection,
after all residue has been
removed, polish the entire
surface with CERAMA BRYTE®
Ceramic Cooktop Cleaner
and a paper towel.
Use a single-edge razor blade
scraper at approximately a 45°
angle against the glass surface
and scrape the soil. It will be
necessary to apply pressure to
the razor scraper in order to
remove the residue.
The CERAMA BRYTE® Ceramic
Cooktop Scraper and all
recommended supplies are
available through our Parts Center.
See instructions under “To Order
Parts” section on next page.
After scraping with the razor
scraper, spread a few drops of
CERAMA BRYTE® Ceramic
Cooktop Cleaner on the entire
burned residue area. Use the
CERAMA BRYTE® Cleaning Pad to
remove any remaining residue.
NOTE: Do not use a dull or
nicked blade.
10
Metal Marks and Scratches
Be careful not to slide pots and pans
across your cooktop. It will leave
metal markings on the cooktop
surface.
If pots with a thin overlay of
aluminum or copper are allowed
to boil dry, the overlay may leave
black discoloration on the cooktop.
These marks are removable using
the CERAMA BRYTE® Ceramic
Cooktop Cleaner with the CERAMA
BRYTE® Cleaning Pad for Ceramic
Cooktops.
This should be removed
immediately before heating
again or the discoloration may
be permanent.
WARNING: Carefully check the bottom of pans
for roughness that would scratch the cooktop.
Glass surface—potential for permanent damage.
Our testing shows that if you
are cooking high sugar
mixtures such as jelly or
fudge and have a spillover, it
can cause permanent
damage to the glass surface
unless the spillover is
immediately removed.
Damage from Sugary Spills and Melted Plastic
Turn off all surface units. Remove
hot pans.
Any remaining spillover should be
left until the surface of the cooktop
has cooled.
Wearing an oven mitt:
a. Use a single-edge razor blade
scraper (CERAMA BRYTE®
Ceramic Cooktop Scraper) to
move the spill to a cool area on
the cooktop.
Don’t use the surface units again
until all of the residue has been
completely removed.
NOTE: If pitting or indentation in the glass
surface has already occurred, the cooktop glass
will have to be replaced. In this case, service will
be necessary.
b. Remove the spill with
paper towels.
To Order Parts
To order CERAMA BRYTE® Ceramic
Cooktop Cleaner and the cooktop
scraper, please call our toll-free number:
National Parts Center
CERAMA BRYTE Ceramic
Cooktop Cleaner . . . . . . . . . . .# WX10X300
800.626.2002.
®
CERAMA BRYTE® Ceramic
Cooktop Scraper . . . . . . . . . . .# WX10X0302
Kit . . . . . . . . . . . . . . . . . . . . . . . .# WB64X5027
(Kit includes cream and cooktop scraper)
CERAMA BRYTE® Cleaning Pads for
Ceramic Cooktops . . . . . . . . .# WX10X350
11
Before You Call For Service…
Troubleshooting Tips
Save time and money! Review the charts on the following
pages first and you may not need to call for service.
Problem
Possible Causes
What To Do
Surface units will not
maintain a rolling boil
or cooking is slow
Improper cookware
being used.
• Use pans which are absolutely flat and match
the diameter of the surface unit selected.
Surface units do
not work properly
A fuse in your home may be
blown or the circuit breaker
tripped.
• Replace the fuse or reset the circuit breaker.
Cooktop controls
improperly set.
• Check to see the correct control is set for the surface
unit you are using.
Tiny scratches or metal
marks (may appear as
cracks) or abrasions on
radiant cooktop glass
surface
Incorrect cleaning
• Use recommended cleaning procedures.
methods being used.
Cookware with rough
bottoms being used or
coarse particles (salt
or sand) were between
the cookware and the
surface of the cooktop.
• Be sure cookware bottoms and cookware are clean
before use. Use cookware with smooth bottoms.
Tiny scratches are not removable but will become
less visible in time as a result of cleaning.
Cookware has been
slid across the cooktop
surface.
Areas of discoloration
or dark streaks on the
cooktop
Improper cookware
being used.
• Marks from aluminum and copper pans as well as
mineral deposits from water or food can be removed
with the cleaning cream.
Hot surface on a model
with a light colored cooktop.
• This is normal. The surface may appear discolored
when it is hot. This is temporary and will disappear
as the glass cools.
Food spillovers not cleaned
before next use.
• See the Cleaning the glass cooktop section.
Incorrect cleaning methods
being used.
• Use recommended cleaning procedures.
Plastic melted to
the surface
Hot cooktop came into
contact with plastic placed
on the hot cooktop.
• See the Glass surface—potential for permanent damage
section in the Cleaning the glass cooktop section.
Pitting (or indentation)
of the cooktop
Hot sugar mixture spilled
on the cooktop.
• Call a qualified technician for replacement.
Frequent cycling off
Improper cookware
• Use only flat cookware to minimize cycling.
and on of surface units being used.
Cooktop feels hot
Improper cookware
being used.
• The glass cooktop surface may seem hotter than you
are used to. This is normal. Use pans which are
absolutely flat.
Control knob will
not turn
Cooktop controls
improperly set.
• When the knob is in the OFF position, it must be
pushed in before it can be turned. When the knob
is in any other position, it can be turned without
being pushed in.
12
™
GE Service Protection Plus
GE, a name recognized worldwide for quality and dependability, offers you
™
Service Protection Plus —comprehensive protection on all your appliances—
No Matter What Brand!
Benefits Include:
• Backed by GE
• All brands covered
• Unlimited service calls
• All parts and labor costs included
• No out-of-pocket expenses
• No hidden deductibles
• One 800 number to call
We’ll Cover Any Appliance.
Anywhere. Anytime.*
You will be completely satisfied with our service protection or you may request your money back
on the remaining value of your contract. No questions asked. It’s that simple.
Protect your refrigerator, dishwasher, washer and dryer, range, TV, VCR and much more—any brand!
Plus there’s no extra charge for emergency service and low monthly financing is available. Even icemaker
coverage and food spoilage protection is offered. You can rest easy, knowing that all your valuable
household products are protected against expensive repairs.
Place your confidence in GE and call us in the U.S. toll-free at 800.626.2224
for more information.
*All brands covered, up to 20 years old, in the continental U.S.
Cut here
✁
Please place in envelope and mail to:
General Electric Company
Warranty Registration Department
P.O. Box 32150
Louisville, KY 40232-2150
13
Consumer Product Ownership Registration
Dear Customer:
Thank you for purchasing our product and thank you for placing your confidence in us.
We are proud to have you as a customer!
Follow these three steps to protect your new appliance investment:
Complete and mail
your Consumer
After mailing the
registration below,
Read your Owner’s
Manual carefully.
It will help you
operate your new
appliance properly.
Product Ownership
Registration today.
Have the peace of
mind of knowing we
can contact you in
the unlikely event of
a safety modification.
store this document
in a safe place. It
contains information
you will need should
you require service.
Our service number is
1
800.GE.CARES
2 3
(800.432.2737).
Model Number
Serial Number
Important: If you did not get a registration card with your
product, detach and return the form below to
ensure that your product is registered, or register
online at GEAppliances.com.
Cut here
✁
Consumer Product Ownership Registration
Model Number
Serial Number
Mr. I Ms. I
Mrs. I
Miss I
First
Name
Last
Name
Street
Address
Apt. #
City
E-mail Address*
Zip
Code
State
Date Placed
In Use
Month
Phone
Number
_
_
Day
Year
* Please provide your e-mail address to receive, via e-mail, discounts, special offers and other important
communications from GE Appliances (GEA).
I Check here if you do not want to receive communications from GEA’s carefully selected partners.
General Electric Company
Louisville, Kentucky
GEAppliances.com
14
GE Electric Cooktop Warranty.
All warranty service provided by our Factory Service Centers,
Staple your receipt here.
Proof of the original purchase
date is needed to obtain service
under the warranty.
or an authorized Customer Care® technician.
To schedule service, on-line, 24 hours a day, visit us at
For The Period Of: GE Will Replace:
One Year
From the date of the
original purchase
Any part of the cooktop which fails due to a defect in materials or workmanship.
During this full one-year warranty, GE will also provide, free of charge, all labor
and in-home service to replace the defective part.
Five Years
From the date of the
original purchase
A replacement glass cooktop if it should crack due to thermal shock, discolor,
or if the pattern wears off.
A replacement radiant surface unit if it should burn out.
During this limited additional four-year warranty, you will be responsible for any labor or
in-home service.
What GE Will Not Cover:
IService trips to your home to teach you how to use the
product.
IDamage to the glass cooktop caused by hardened spills
of sugary materials or melted plastic that are not cleaned
according to the directions in the Owner’s Manual.
IImproper installation.
IReplacement of house fuses or resetting of circuit
breakers.
IFailure of the product if it is abused, misused, or used
for other than the intended purpose or used
commercially.
IDamage to the product caused by accident, fire, floods
or acts of God.
IDamage to the glass cooktop caused by use of cleaners
other than the recommended cleaning creams and
pads.
IIncidental or consequential damage caused by possible
defects with this appliance.
This warranty is extended to the original purchaser and any succeeding owner for products purchased for
home use within the USA. In Alaska, the warranty excludes the cost of shipping or service calls to your home.
Some states do not allow the exclusion or limitation of incidental or consequential damages. This warranty
gives you specific legal rights, and you may also have other rights which vary from state to state. To know
what your legal rights are, consult your local or state consumer affairs office or your state’s Attorney General.
Warrantor: General Electric Company. Louisville, KY 40225
15
Consumer Support.
GE Appliances Website
Have a question or need assistance with your appliance? Try the GE Appliances Website 24 hours a day,
any day of the year! For greater convenience and faster service, you can now download Owner’s Manuals,
order parts, catalogs, or even schedule service on-line. You can also “Ask Our Team of Experts™”
your questions, and so much more...
Schedule Service
Expert GE repair service is only one step away from your door. Get on-line and schedule your service at
your convenience 24 hours any day of the year! Or call 800.GE.CARES (800.432.2737) during normal
business hours.
Real Life Design Studio
GE supports the Universal Design concept—products, services and environments that can be used by
people of all ages, sizes and capabilities. We recognize the need to design for a wide range of physical and
mental abilities and impairments. For details of GE’s Universal Design applications, including kitchen
design ideas for people with disabilities, check out our Website today. For the hearing impaired, please call
800.TDD.GEAC (800.833.4322).
Extended Warranties
Purchase a GE extended warranty and learn about special discounts that are available while your warranty
is still in effect. You can purchase it on-line anytime, or call 800.626.2224 during normal business hours.
GE Consumer Home Services will still be there after your warranty expires.
Parts and Accessories
Individuals qualified to service their own appliances can have parts or accessories sent directly to their
homes (VISA, MasterCard and Discover cards are accepted). Order on-line today, 24 hours every day or
by phone at 800.626.2002 during normal business hours.
Instructions contained in this manual cover procedures to be performed by any user. Other servicing generally
should be referred to qualified service personnel. Caution must be exercised, since improper servicing may cause
unsafe operation.
Contact Us
If you are not satisfied with the service you receive from GE, contact us on our Website with all the details
including your phone number, or write to: General Manager, Customer Relations
GE Appliances, Appliance Park
Louisville, KY 40225
Register Your Appliance
Register your new appliance on-line—at your convenience! Timely product registration will allow for
enhanced communication and prompt service under the terms of your warranty, should the need arise.
You may also mail in the preprinted registration card included in the packing material.
Printed in the United States
|