Owner’s Manual
Please read before using this unit.
DVD/CD Player with Video Cassette Recorder
INSTRUCCIONES EN ESPAÑOL INCLUIDAS.
MSD805
Supplied Accessory
• Remote control
(NB183UD)
• RF cable
(WPZ0901TM002)
with two AA batteries
• Audio/Video cables
(WPZ0102TM015 or
WPZ0102LTE01)
• Owner’s Manual
(1VMN20455)
If you need additional operating assistance after
reading this owner’s manual, please call
TOLL FREE : 1-800-605-8610
Owner's Manual
Table of Contents
I Recording . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Recording & OTR (One Touch Recording) . . . . . . . . . . . . . . . . 12
Timer Recording. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Hints for OTR and Timer Recording . . . . . . . . . . . . . . . . . . . . . 13
Copying a Video Tape. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Precautions
Laser Safety. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
I IMPORTANT SAFEGUARDS . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Installation Location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Avoid the Hazards of Electrical Shock and Fire. . . . . . . . . . . . . . 4
Moisture Condensation Warning. . . . . . . . . . . . . . . . . . . . . . . . . 4
About Copyright . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Notice for Progressive Scan Outputs . . . . . . . . . . . . . . . . . . . . . 4
Symbols Used in This Manual . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
I About the Video Cassettes and Discs . . . . . . . . . . . . . . . . . . . 5
Playable Video Cassettes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Playable Discs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Unplayable Discs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
DVD Functions
I Playback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
I On-Screen Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
I Search Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Track Search / Title/Chapter Search / Time Search . . . . . . . . . 17
I Marker Setup. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
I Repeat / Random / Programmed Playback . . . . . . . . . . . . . . 18
Repeat Playback / Repeat A-B Playback /
Random Playback / Programmed Playback. . . . . . . . . . . . . . . . 18
I Special Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Subtitle Language / Audio Language / Camera Angle /
Setup
I Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
RF Output Channel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Hint for Cable Box or Satellite Box . . . . . . . . . . . . . . . . . . . . . . . 6
Connection to an Audio System . . . . . . . . . . . . . . . . . . . . . . . . . 6
Connection to a TV . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Front & Rear Terminals. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
I Preparation for Use. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Turn On the Unit for the First Time . . . . . . . . . . . . . . . . . . . . . . . 8
To Add/Delete Channels. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Clock Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
I Function Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Front Panel Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
VCR/DVD Switching. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Remote Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Installing the Batteries for the Remote Control . . . . . . . . . . . . . 10
Black Level Setting / Stereo Sound Mode / Virtual Surround . . . . . . . 19
I DVD Setup. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
LANGUAGE Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
DISPLAY Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
AUDIO Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
PARENTAL Setting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
OTHERS Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Reset to the Default Setting (Except for PARENTAL Setting). . . 23
Information
I Troubleshooting Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
I Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
I Language List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
I Limited Warranty. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Español . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Quick Use Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
VCR Functions
I Playback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
I Other Operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Index Search . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Time Search. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Auto Repeat. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Basic TV Connection
Antenna
or
Cable TV Antenna
signal
or
Cable TV
signal
(Back of DVD/VCR)
(Back of TV)
4
AC
outlets
(Back of TV)
Plug in
ANT-IN
2
ANT-OUT
Disconnect
3
Connect
Connect
From DVD/VCR
From TV
RF cable (supplied)
Please refer to “Connections” on page 6.
5
IMPORTANT SAFEGUARDS
1. Read Instructions - All the safety and operating instruc-
tions should be read before the appliance is operated.
2. Retain Instructions- The safety and operating instructions
should be retained for future reference.
3. Heed Warnings - All warnings on the appliance and in the
operating instructions should be adhered to.
4. Follow Instructions - All operating and use instructions
should be followed.
proper grounding of the mast and supporting structure,
grounding of the lead-in wire to an antenna discharge unit,
size of grounding conductors, location of antenna-dis-
charge unit, connection to grounding electrodes, and
requirements for the grounding electrode. (Fig. A)
FIGURE A
ANTENNA
EXAMPLE OF ANTENNA GROUNDING
AS PER NATIONAL ELECTRICAL CODE
LEAD
WIRE
5. Cleaning - Unplug this video product from the wall outlet
before cleaning. Do not use liquid cleaners or aerosol
GROUND
CLAMP
ANTENNA
DISCHARGE UNIT
(NEC SECTION 810-20)
cleaners. Use
a
damp cloth for cleaning.
EXCEPTION: A product that is meant for uninterrupted
service and, that for some specific reason, such as the
possibility of the loss of an authorization code for a CATV
converter, is not intended to be unplugged by the user for
cleaning or any other purpose, may exclude the reference
to unplugging the appliance in the cleaning description
otherwise required in item 5.
6. Attachments - Do not use attachments not recommended
by the video product manufacturer as they may cause haz-
ards.
7. Water and Moisture- Do not use this video product near
water, for example, near a bath tub, wash bowl, kitchen
sink, or laundry tub, in a wet basement, or near a swim-
ming pool, and the like.
8. Accessories - Do not place this video product on an unsta-
ble cart, stand, tripod, bracket, or table. The video product
may fall, causing serious injury to a child or adult, and seri-
ous damage to the appliance. Use only with a cart, stand,
tripod, bracket, or table recommended by the manufactur-
er, or sold with the video product. Any mounting of the
appliance should follow the manufactur-
er's instructions and should use a
mounting accessory recommended by
the manufacturer. An appliance and cart
combination should be moved with care.
Quick stops, excessive force, and
uneven surfaces may cause the appli-
ance and cart combination to overturn.
9. Ventilation - Slots and openings in the cabinet are provid-
ed for ventilation and to ensure reliable operation of the
video product and to protect it from overheating, and these
openings must not be blocked or covered. The openings
should never be blocked by placing the video product on a
bed, sofa, rug, or other similar surface. This video product
should not be placed in a built-in installation such as a
bookcase or rack unless proper ventilation is provided or
the manufacturer's instructions have been adhered to.
ELECTRIC
SERVICE
EQUIPMENT
GROUNDING CONDUCTORS
(NEC SECTION 810-21)
GROUND CLAMP
NEC – NATIONAL ELECTRICAL CODE
POWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ART 250, PART H)
S2898A
14. Lightning - For added protection for this video product dur-
ing a lightning storm, or when it is left unattended and
unused for long periods of time, unplug it from the wall out-
let and disconnect the antenna or cable system. This will
prevent damage to the video product due to lightning and
power-line surges.
15. Power Lines - An outside antenna system should not be
located in the vicinity of overhead power lines or other
electric light or power circuits, or where it can fall into such
power lines or circuits. When installing an outside antenna
system, extreme care should be taken to keep from touch-
ing such power lines or circuits as contact with them might
be fatal.
16. Overloading - Do not overload wall outlets and extension
cords as this can result in a risk of fire or electric shock.
17. Object and Liquid Entry - Never push objects of any kind
into this video product through any openings as they may
touch dangerous voltage points or short-out parts that
could result in a fire or electric shock. Never spill liquid of
any kind on the video product.
18. Servicing - Do not attempt to service this video product
yourself as opening or removing covers may expose you
to dangerous voltage or other hazards. Refer all servicing
to qualified service personnel.
19. Damage Requiring Service - Unplug this video product
from the wall outlet and refer servicing to qualified service
personnel under the following conditions:
a. When the power-supply cord or plug is damaged.
b. If liquid has been spilled, or objects have fallen into the
video product.
10. Power Sources - This video product should be operated
only from the type of power source indicated on the mark-
ing label. If you are not sure of the type of power supply to
your home, consult your appliance dealer or local power
company. For products intended to operate from battery
power, or other sources, refer to the operating instructions.
11. Grounding or Polarization - This video product is equipped
with a polarized alternating-current line plug (a plug having
one blade wider than the other). This plug will fit into the
power outlet only one way. This is a safety feature. If you
are unable to insert the plug fully into the outlet, try revers-
ing the plug. If the plug should still fail to fit, contact your
electrician to replace your obsolete outlet. Do not defeat
the safety purpose of the polarized plug.
12. Power Cord Protection - Power supply cords should be
routed so that they are not likely to be walked on or
pinched by items placed upon or against them, paying par-
ticular attention to cords at plugs, convenience recepta-
cles, and the point where they exit from the appliance.
13. Outdoor Antenna Grounding - If an outside antenna or
cable system is connected to the video product, be sure
the antenna or cable system is grounded so as to provide
some protection against voltage surges and built-up static
charges. Article 810 of the National Electrical Code,
ANSI/NFPA No. 70, provides information with regard to
c. If the video product has been exposed to rain or water.
d. If the video product does not operate normally by following
the operating instructions. Adjust only those controls that
are covered by the operating instructions as an improper
adjustment of other controls may result in damage and will
often require extensive work by a qualified technician to
restore the video product to its normal operation.
e. If the video product has been dropped or damaged in any
way.
f. When the video product exhibits a distinct change in per-
formance this indicates a need for service.
20. Replacement Parts - When replacement parts are
required, be sure the service technician has used replace-
ment parts specified by the manufacturer or have the
same characteristics as the original part. Unauthorized
substitutions may result in fire, electric shock or other haz-
ards.
21. Safety Check - Upon completion of any service or repairs
to this video product, ask the service technician to perform
safety checks to determine that the video product is in
proper operating condition.
22. Heat - This video product should be situated away from
heat sources such as radiators, heat registers, stoves, or
other products (including amplifiers) that produce heat.
EN
–
–
3
Installation Location
Maintenance
For safety and optimum performance of this unit:
• Do not stand the unit up vertically. Install the unit in
a horizontal and stable position. Do not place any-
thing directly on top of the unit. Do not place the unit
directly on top of the TV.
• Shield it from direct sunlight and keep it away from
sources of intense heat. Avoid dusty or humid
places. Avoid places with insufficient ventilation for
proper heat dissipation. Do not block the ventilation
holes on the sides of the unit. Avoid locations sub-
ject to strong vibration or strong magnetic fields.
• Be sure to remove a disc and unplug the AC
power cord from the outlet before carrying the unit.
SERVICING
¡
Please refer to relevant topics on the “Troubleshooting
Guide” on page 23 before returning the product.
¡If this unit becomes inoperative, do not try to correct
the problem by yourself. There are no user-service-
able parts inside. Turn off, unplug the power plug,
and please call our help line mentioned on the front
page to locate an Authorized Service Center.
CLEANING THE CABINET
¡Use a soft cloth slightly moistened with a mild deter-
gent solution. Do not use a solution containing alco-
hol, spirits, ammonia or abrasive.
CLEANING DISCS
Avoid the Hazards of Electrical Shock and Fire
¡When a disc becomes dirty, clean it with a cleaning
cloth. Wipe the disc from the center out. Do not wipe
in a circular motion.
• Do not handle the power cord with wet hands.
• Do not pull on the power cord when disconnecting it
from AC wall outlet. Grasp it by the plug.
• If, by accident, water is spilled on this unit, unplug
the power cord immediately and take the unit to our
Authorized Service Center for servicing.
• Do not put your fingers or objects into the unit cas-
sette holder.
¡
Do not use solvents such as benzine, thinner, commercial-
ly available cleaners, detergent, abrasive cleaning agents
or antistatic spray intended for analog records.
CLEANING THE DISC LENS
¡If this unit still does not perform properly although you
refer to the relevant sections and to “Troubleshooting
Guide” in this Owner’s Manual, the laser optical pick-
up unit may be dirty. Consult your dealer or an
Authorized Service Center for inspection and clean-
ing of the laser optical pickup unit.
Moisture Condensation Warning
Moisture condensation may occur inside the unit
when it is moved from a cold place to a warm place,
or after heating a cold room or under conditions of
high humidity. Do not use this unit at least for 2 hours
until its inside gets dry.
DISC HANDLING
¡When you handle a disc, hold it by its edge and try
not to touch the surface of the disc.
¡Always store the disc in its protective case when it is
not used.
About Copyright
Unauthorized copying, broadcasting, public perfor-
mance and lending of discs are prohibited.
AUTO HEAD CLEANING
¡Automatically cleans video heads as you insert or
remove a cassette, so you can see a clear picture.
¡Playback picture may become blurred or interrupted
while the TV program reception is clear. Dirt accu-
mulated on the video heads after a long period of
use, or the usage of rental or worn tapes can cause
this problem. If a streaky or snowy picture appears
during playback, the video heads in your unit may
need to be cleaned.
This product incorporates copyright protection tech-
nology that is protected by U.S. patents and other
intellectual property rights. Use of this copyright pro-
tection technology must be authorized by Macrovision,
and is intended for home and other limited viewing
uses only unless otherwise authorized by Macrovision.
Reverse engineering or disassembly is prohibited.
Notice for Progressive Scan Outputs
1. Please visit your local Audio/Video store and pur-
chase a good quality VHS Video Head Cleaner.
2. If a Video Head Cleaner does not solve the problem,
please call our help line mentioned on the front page
to locate an Authorized Service Center.
Consumers should note that not all high definition televi-
sion sets are fully compatible with this product and may
cause artifacts to be displayed in the picture. In case of
picture problems with 525 progressive scan output, it is
recommended that the user switch the connection to the
‘standard definition’ output. If there are questions regard-
ing your TV set compatibility with this 525p DVD player,
please contact our customer service center.
Hint
• Remember to read the instructions along with the video head
cleaner before use.
• Clean video heads only when problems occur.
Symbols Used in This Manual
Note to CATV system installer
The following symbols appear in some head-
ings in this manual.
This reminder is provided to call the CATV system
installer’s attention to Article 820-40 of the NEC that
provides guidelines for proper grounding and, in par-
ticular, specifies that the cable ground should be
connected to the grounding system of the building,
as close to the point of cable entry as practical.
VCR
: Description refers to playback or recording
of video cassette tapes.
: Description refers to playback of DVD-Video
discs.
DVD-V
CD
: Description refers to playback of Audio
CDs.
Manufactured under license from Dolby
Laboratories. “Dolby” and the double-D symbol
are trademarks of Dolby Laboratories.
EN
–
–
4
About the Video Cassettes and Discs
Playable Video Cassettes
Use only cassettes marked
with this unit.
Playable Discs
Recorded
signals
Playable
Mark (logo)
discs
Disc size
Region code
Disc types
DVD-Video
* 1, 2, 4, 6
or
DVD-RW
DVD-R
Example
12 cm
or
8cm
Title 1
Title 2
Digital video
(MPEG2)
-
-
Chapter 1 Chapter 2 Chapter 3 Chapter 4 Chapter 1
Chapter 2
* 1, 3, 4, 5,
6, 7, 9, 10
DVD+RW
DVD+R
* 1, 3, 4,
5, 6, 8
Audio CD
* 4, 6
Example
12 cm
or
-
Digital audio
CD-RW
CD-R
Track 1
Track 2
Track 5
Track 6
Track 3
Track 4
8cm
* 4, 5, 6,
9, 10
is a trademark of DVD Format/Logo Licensing Corporation.
If you cannot play back a disc which bears one of the marks above, check the following notes.
*1: This unit conforms to the NTSC color system. Discs recorded in other color systems such as PAL cannot be played back.
*2: Certain DVD-Video discs do not operate as described in this manual due to the intentions of the disc’s producers.
*3: Discs recorded in the VR (Video Recording) format cannot be played back.
*4: Scratched or stained discs may not be played back.
*5: Some discs cannot be played back because of incompatible recording conditions, characteristics of the recorder or spe-
cial properties of discs.
*6:You can play back discs which bear the marks above. If you use nonstandardized discs, this unit may not play them back.
Even if they are played back, the sound or video quality will be compromised.
*7:You may play back the unfinalized DVD-R/RW disc recorded in the video format on our brand’s DVD recorder. However,
depending on the recording status of a disc, the disc may not be played back at all or normally (the picture or sound may
not be smooth, etc.). In this case, you need to finalize the disc with the DVD recorder. Refer to the manual accompanying
the DVD recorder.
*8: Only the discs recorded in the video format and finalized can be played back.
Unfinalized discs cannot be played back. Depending on the recording status of a disc, the disc may not be played back at
all or normally (the picture or sound may not be smooth, etc.).
*9: If there is too much recording space left on a disc (the used portion is less than 55 mm across), it may not play back properly.
*10: Do not glue paper or put stickers on to the disc. These may damage the disc, and the unit may not read it correctly.
Unplayable Discs
¡
NEVER play back the following discs. Otherwise, malfunction may result!
DVD-RAM / CD-I / Photo CD / Video CD / DVD with region codes other than 1 or ALL /
DTS-CD /
DVD-ROM for personal computers / CD-ROM for personal computers
¡
On the following disc, the sound MAY NOT be heard.
Super Audio CD
NOTE: Only the sound recorded on the normal CD layer can be delivered.
The sound recorded on the high density Super Audio CD layer cannot be delivered.
Any other discs without compatibility indications.
¡
EN
–
–
5
Setup
Connections
Please refer to “Basic TV Connection” on the front page before you use this unit.
RF Output Channel
If channel 3 is already occupied for broadcasting,
1) Set your TV to channel 4.
2) Insert a pre-recorded tape into this unit.
5) After a few seconds, hit [PLAY B] on the
Hint
unit for 3 seconds.
•
The RF output channel may
not change when you adjust
tracking during playback. In this
case, stop the playback, and
start the playback again. After
that, hit [PLAY B] on the unit
for 3 seconds again.
•
The RF output channel will change to chan-
nel 4 from channel 3 and you will see a play-
back picture.
3) Hit [SOURCE] on the unit so that the VCR
OUTPUT light is lit.
• When a picture does not appear on the
•
If noise appears on the TV screen, hit
[VCR/TV] on the remote control.
TV screen, repeat step 4).
6) Hit [STOP C] to stop playback.
4) Hit [PLAY B] once.
Hint for Cable Box or Satellite Box
(Back of DVD/VCR)
(Cable box or
Satellite box)
To select channels of the cable box or satellite box
Satellite or
Cable TV
signal
ANT-IN
1) Turn on the unit by hitting [STANDBY-ON], then hit
[VCR/TV].The “POWER-ON” light on the front panel will
appear, then pressing [SKIP/CH. i/K j/L] to select
channel 3 or 4 (the same channel as the output channel of the
cable box or satellite box).
IN
OUT
ANT-OUT
E
RF cable
(supplied)
(Back of TV)
• If you use the channel 4, you need to change the unit’s RF
output to channel 4. Refer to “RF Output Channel”.
2) At the TV, select channel 3 or 4 (the same channel as you
have selected at step 1).
3) On the cable box or satellite box, select the channel you want
to view or record.
Select this connection when you want to view or record a scram-
bled channel. With this connection, channels cannot be changed
on the unit. You can view or record ONLY the channels you have
selected on the cable box or the satellite box.
• While you are recording, only the recorded channel can be
viewed.
Connection to an Audio System
Method 1
Method 2
Dolby Digital decoder,
MD deck or DAT deck
Stereo system
L
R
COAXIAL
Analog audio
input jacks
Digital audio
input jack
AUDIO
Audio Coaxial
Digital cable
(commercially
available)
Audio cable
(supplied)
DVD/VCR
AUDIO OUT
VCR
DVD
AUDIO S-VIDEO
OUT OUT
COMPONENT
DIGITAL
VIDEO OUT
AUDIO OUT
L
(Analog)
AUDIO OUT
DIGITAL
AUDIO OUT
R
COAXIAL
DVD/VCR
or
DVD
Setting
SETUP > AUDIO menu >
COMPONENT
VIDEO OUT
DIGITAL
AUDIO OUT
AUDIO S-VIDEO
OUT OUT
Connection
DOLBY DIGITAL
L
Connecting to a Dolby Digital decoder
for Dolby Digital audio output.
BITSTREAM
R
Connecting to the other equipment (an MD deck
or DAT deck etc.) without Dolby Digital decoder.
PCM
(DVD mode only)
SETUP > AUDIO menu >
DOLBY DIGITAL
PCM
* To complete these settings, refer to pages 20-21.
Setting
Connection
Connecting to Stereo System.
Hint
•
The audio source on a disc in a Dolby Digital 5.1 channel surround
format cannot be recorded as digital sound by an MD or DAT deck.
* To complete these settings, refer to pages 20-21.
• By hooking this unit up to a Multi-channel Dolby Digital
decoder, you can enjoy high-quality Dolby Digital 5.1
channel surround sound as heard in the movie theaters.
• Playing a DVD using incorrect settings may generate
noise distortion and may also damage the speakers.
Hint
• Playing a DVD using incorrect settings may generate
noise distortion and may also damage the speakers.
EN
–
–
6
Connection to a TV
Method 1
Method 2
Method 3
Basic Audio
Good picture
Better picture
Best picture
COMPONENT
VIDEO IN
AUDIO IN
TV
Y
Y
L
R
S-VIDEO IN
VIDEO IN
P
B
CB
or
P
R
CR
Audio cable
(supplied)
Video
cable
(supplied)
S-Video
cable
(commercially
Component Video cables
(commercially available)
available)
DVD/VCR
AUDIO OUT
VCR
DVD/VCR
L
DVD
AUDIO S-VIDEO
OUT OUT
DVD/VCR
AUDIO OUT
COMPONENT
VIDEO OUT
DIGITAL
AUDIO OUT
Y
L
DVD
AUDIO S-VIDEO
OUT OUT
A
V
L
R
C
/
/
DVD/VCR
VCR
DVD
AUDIO S-VIDEO
OUT OUT
PB
B
R
COMPONENT
COAXIAL
VIDEO OUT
R
C
COMPONENT
VIDEO OUT
VIDEO OUT
PR
R
VIDEO OUT
Y
C
/
/
PB
B
or
VIDEO OUT
DVD
C
PR
DIGITAL
AUDIO S-VIDEO
OUT OUT
R
AUDIO OUT
L
VIDEO OUT
S-VIDEO OUT
COMPONENT VIDEO OUT
(Analog)
R
AUDIO OUT
Hint
•
Connect this unit directly to the TV. If the Audio/Video cables are connected to a VCR, pictures may be distorted due to the copy protection system.
• When progressive scanning mode is selected, no video signal will be output from the VIDEO OUT or S-VIDEO OUT jack.
• The COAXIAL, DVD AUDIO OUT, S-VIDEO OUT and COMPONENT VIDEO OUT jacks are only useful in DVD mode.
[DVD/VCR]
If your TV is compatible with 525p (480p) progressive scanning and you want to
enjoy that high quality picture;
VD
P.SCAN
PLAY
U
P
O
T
You must select the connection Method 3 above and progressive scanning mode. To set the mode,
press and hold [PLAY B] on the front panel for more than 5 seconds, so that the P.SCAN indicator
will appear on the display of this unit. (The progressive scanning is not available in the VCR mode.)
If your TV is not compatible with progressive scanning;
PREV
STOP
PLAY
N
more than 5 seconds
[Interlace mode]
Use this unit in interlace mode. Make sure that no P.SCAN indicator is on the display of this unit. If not, press and hold
[PLAY B] on this unit for more than 5 seconds, so that the P.SCAN indicator on the display of this unit will disappear. [Progressive scanning mode]
After you have completed connections
• Hit the input selector button (usually TV/VIDEO, INPUT or AUX) on your TV to switch an appropriate external input chan-
nel (usually near channel 0) for viewing the picture from this unit.
If the picture does not appear, also refer to the manual accompanying your TV.
Input modes for common TV brands (Example)
• Listed below are inputs for common brand name TV’s.
Admiral:
Curtis Mathis:
GE:
AUX
Panasonic:
RCA:
TV/VIDEO
LINE1, LINE2, 00, 90, 91, 92, 93
INPUT, TV/VCR, 00, 90, 91, 92, 93
INPUT, TV/VCR, 00, 90, 91, 92, 93
Samsung:
Sanyo:
TV/VIDEO
Hitachi:
INPUT, AUX
VIDEO
JVC:
A/V CHANNEL, INPUT1, SVIDEO, INPUT2
Sharp:
00
Kenwood:
LXI-Series:
Magnavox:
AUX
00
Sony:
VIDEO1, VIDEO2, VIDEO3
Toshiba:
Zenith:
TV/GAME
00
AUX CHANNEL
Front & Rear Terminals
DVD AUDIO OUT (analog) jacks DVD/VCR AUDIO OUT jacks
AUDIO IN jack
ANT-IN jack
Connect the supplied audio
cables here through the audio
Connect the supplied audio
cable here through the audio
Connect an audio cable com-
ing from the audio output jack
of a camcorder, another VCR
or an audio source here.
Connect your antenna
or cable box here.
input jacks of a television or other input jacks of a television or
VIDEO
AUDIO
audio equipment. (DVD only)
other audio equipment.
R
REW
DVD
AUDIO S-VIDEO
OUT OUT
DVD/VCR
AUDIO OUT
VCR
COMPONENT
VIDEO OUT
DIGITAL
ANT-IN
R
VCR
AUDIO OUT
DIGITAL AUDIO OUT COAXIAL jack
Connect an optional coaxial digital
audio cable here through the coaxial
digital audio input jack of a decoder
or audio receiver. (DVD only)
ANT-IN
Y
L
UDIO IN
O IN
[Front Panel]
AUDIO IN
VIDEO IN
L
ANT-OUT
C
/
/
R
VIDEO OUT
PB
B
ANT-OUT
COAXIAL
R
C
PR
R
[Rear Panel]
ANT-OUT jack
Connect the
S-VIDEO OUT jack
VIDEO IN jack
COMPONENT VIDEO OUT jacks
Connect optional component
video cables here through the
component video input jacks of
a television. (DVD only)
DVD/VCR VIDEO OUT jack
Connect the supplied video
cable here through the TV’s
video input jack.
supplied RF
Connect an optional
S-Video cable here
through the S-video
input jack of a tele-
vision. (DVD only)
Connect a cable coming
from the video output jack
of a camcorder, another
VCR or an audio-visual
source (laser disc player,
video disc player, etc.) here.
cable to the
antenna input
jack on your TV.
EN
–
–
7
Preparation for Use
Hint
Turn On the Unit for the
First Time
To Add/Delete Channels
• If you accidentally select Spanish or
French and need English: hit [MENU] and
choose SELEC. IDIOMA or SELECTION
LANGUE. Hit [B] and select ENGLISH.
Finally, hit [CLEAR/C.RESET].
- M E N U -
1
VCR
MENU
TIMER PROGRAMMING
AUTO REPEAT [OFF]
B CHANNEL SET UP
CLOCK SET
VCR
1
LANGUAGE SELECT
Turn on the TV and set it
to channel 3.
Clock Set Up
VCR
• If the clock is not set, the
CLOCK SET screen
appears when you hit
[MENU]. In this case, hit
[MENU] again.
• If channel 3 is already occupied for broadcasting,
see“RF Output Channel” section.
VCR
or
- M E N U -
1
MENU
TIMER PROGRAMMING
AUTO REPEAT [OFF]
CHANNEL SET UP
B CLOCK SET
LANGUAGE SELECT
2
STANDBY-ON Remote Control TV Screen
2
3
CHANNEL SET UP
LANGUAGE SELECT
• If the clock is not set, the
CLOCK SET screen
AUTO SET UP
B ENGLISH
FRANCAIS
ESPAÑOL
[ON]
or
appears when you hit
B MANUAL SET UP
[MENU]. In this case, go
or
to step 2).
or
2
CLOCK SET
MONTH DAY
1 0 – –
YEAR
– – – –
MANUAL SET UP
/
3
CH 01
CHANNEL 30
ADD
(CATV)
or
HOUR MINUTE AM/PM
– – – – – –
:
or
AUTO SET UP
Select the current month.
Select the channel to
be added or deleted.
Do you connect the cable from the cable box or
the satellite box to the unit’s ANT-IN jack?
YES
3
4
CLOCK SET
MONTH DAY
1 0 0 3
YEAR
– – – –
4
5
/
MANUAL SET UP
Yes Hit [MENU] to
or
HOUR MINUTE AM/PM
– – – – – –
CHANNEL 30
DELETE
(CATV)
exit.
:
•
Refer to “Hint for Cable Box or
Satellite Box” section on page 6.
or
NO
Select the current day.
No Please wait for a few minutes.
After scanning...
Select “ADD” or “DELETE”.
•
•
The tuner stops on the lowest memorized channel.
You can select only the channels memorized
in this unit by using [SKIP/CH.
G
/
K
/ ]
H L
(or [CHANNEL ]).
K
/
L
CLOCK SET
• If "AUTO SET UP" appears on the TV
To exit the
menu
CLEAR/
C. RESET
MONTH DAY
1 0 0 3
YEAR
2 0 0 5
screen again, check the cable connections.
/
Then, hit [B] once again.
or
HOUR MINUTE AM/PM
– – – – – –
Hint
:
• Repeat these steps only if either there
was a power failure or this unit has been
unplugged for more than 30 seconds.
To Preset the Channel Again
1) Hit [MENU] until the main menu appears.
Select the current year.
2) Select “CHANNEL SET UP” by pressing
To Select a Channel
You can select a channel using
the Number buttons or
[K/L
3) Select “AUTO SET UP” by pressing [K/L
then hit [B . After scanning, the tuner
stops on the lowest memorized channel.
], then hit [B].
]
,
]
[SKIP/CH.
control.
G
/
K
H
/
L
]
on the remote
5
CLOCK SET
MONTH DAY
YEAR
Notes for using the Number buttons:
• When selecting cable channels which
are higher than 99, enter channel
numbers as a three-digit number.(For
example: 117, hit [1], [1], [7])
• You must precede single-digit channel
numbers with a zero (for example: 02,
03, 04 and so on).
1 0 0 3 MON 2 0 0 5
/
To Change the On-Screen Language
1) Hit [MENU] until the main menu appears.
or
HOUR MINUTE AM/PM
0 5 – – – –
:
2) Select “LANGUAGE SELECT” by pressing
[K/L], then hit [B].
Select the current hour.
3) Select “ENGLISH” , “FRANCAIS” or
“ESPAÑOL” by pressing [K/L], then hit
[CLEAR/C.RESET].
EN
–
–
8
6
7
8
To exit the CLOCK SET
screen
CLOCK SET
MONTH DAY YEAR
CLOCK SET
MONTH DAY YEAR
1 0 0 3 MON 2 0 0 5
/
1 0 0 3 MON 2 0 0 5
/
or
or
HOUR MINUTE AM/PM
HOUR MINUTE AM/PM
0 5 4 0 – –
0 5
:
4 0
P M AM
:
B PM
Select “AM” or “PM”.
Select the current minute.
Hint
• To go back one step, hit [s] (during steps
2) to 7) ).
• Your clock setting will be lost if either there
is a power failure or this unit has been
unplugged for more than 30 seconds.
Function Overview
Front Panel Indicator
Lights up when power is on.
Lights up when the inserted disc is being played back.
Flashes when an unacceptable disc is installed.
Lights up during a recording.
Flashes when a recording is paused.
STANDBY-ON
OPEN/
N
y
CLOSE
POWER-ON
REC
TIMER
VCR
DVD
P.SCAN
PLAY
VIDEO
AUDIO
R
Q
PN
U
P
O
T
O
X
Y
REW
F.FWD STOP/EJECT PLAY RECORD
IR
CHANNEL
SOURCE
PREV
STOP
PLAY
NEXT
Lights up when the progressive scan
system is activated.
Lights up when the Timer Recording
or an OTR recording has been set.
VCR/DVD Switching
Because this product is a combination of a VCR and
a DVD player, you must select first which compo-
nent you wish to operate with [SOURCE].
STANDBY-ON
OPEN/
N
OPEN/CLOSE
/EJECT
y
CLOSE
STANDBY-ON
SPEED
AUDIO
POWER-ON
REC
TIMER
VCR
DVD
P
.SCAN
PLAY
VIDEO
AUDIO
R
Q
PN
O
U
P
O
T
X
Y
REW
F
.FWD STOP/EJECT PLAY RECORD
IR
CHANNEL
SOURCE
PREV
STOP
PLAY
NEXT
1
4
7
2
5
8
3
6
9
SKIP/CH.
VCR MODE
Hit [VCR] on the remote control.
(Verify that the VCR OUTPUT light is lit.)
VCR/TV
SLOW
0
VCR
+1 0
DVD
VCR button
DVD button
DISPLAY
PAUSE
PLAY
DVD MODE
STOP
VCR OUTPUT
light
RECORD
MENU
Hit [DVD] on the remote control.
ENTER
(Verify that the DVD OUTPUT light is lit.)
VCR
DVD
SETUP TOP MENU
RETURN
DVD OUTPUT
light
SEARCH
MODE
CLEAR/
C. RESET
MODE
ZOOM
SUBTITLE
T-SET
Hint
ANGLE
REPEAT
A-B
• Hitting only [SOURCE] on the front panel DOES NOT
switch the mode of the remote control. You MUST select
the correct mode on the remote control.
SOURCE
SOURCE button
EN
–
–
9
Remote Control
VCR mode
DVD mode
Disc/Tape
(BAulpthtaobnetical order)
OPEN/CLOSE
/EJECT
STANDBY-ON
SPEED
AUDIO
1
4
7
2
5
8
0
3
•To select channel.
•The +10 button has no effect
in VCR mode.
6
1
4
7
2
5
8
3
6
9
•
To select chapter or title directly. •To select track directly.
SKIP/CH.
9
+1 0
VCR/TV
SLOW
•To search forward/backward
through a disc.
•To search forward/backward
•To forward/backward a tape.
0
VCR
+1 0
DVD
•
To begin slow forward/reverse
through a disc.
DISPLAY
PAUSE
playback during the pause mode.
• To select an item
on the VCR Menu.
ENTER
PLAY
•To move the cursor and
•To move the cursor and
• To advance to the next
VCR Menu.
determine its position.
determine its position.
STOP
•
To go back one step during
RECORD
MENU
clock and timer setting.
A-B
•To repeat between your
•To repeat between your
ENTER
chosen point A and B.
chosen point A and B.
SETUP TOP MENU
RETURN
ANGLE
AUDIO
•To select camera angles on
SEARCH
MODE
CLEAR/
C. RESET
a disc.
MODE
ZOOM
•To select audio languages on •To select STEREO,
SUBTITLE
T-SET
ANGLE
REPEAT
A-B
a disc.
L-ch or R-ch.
•To clear the markers.
•To clear the markers.
•To clear the numbers.
entered incorrectly.
CLEAR/
•
To remove status number in
C. RESET
•To exit the VCR Menu.
program input.
To clear the numbers entered incorrectly.
To cancel the point for A-B repeat.
•To reset the tape counter.
•
•
•
To cancel the point for A-B repeat.
DISPLAY
DVD
•To display the current disc
•To display the current disc
•To display the current time,
mode.
mode.
tape counter, and channel.
• To select the DVD output
• To select the DVD output
mode.
mode.
• To activate the remote control • To activate the remote control
in DVD mode.
in DVD mode.
Installing the Batteries
for the Remote Control
MENU
MODE
•To call up the Menu
•To call up the VCR Menu.
on a disc.
•To arrange the playing
order or play randomly.
•To set black level on/off.
Install two AA batteries (supplied) match-
ing the polarity indicated inside battery
compartment of the remote control.
•To set virtual surround on/off.
•To set virtual surround on/off.
OPEN/CLOSE
/EJECT
•To open or close the disc
•To open or close the disc
•To eject the video cassette
tray.
tray.
from the VCR.
1
2
3
• To pause tape playback or
recording.
PAUSE
•To pause disc playback.
•To advance playback
one frame at a time.
• To pause disc playback.
•To advance playback
one frame at a time.
• To begin tape playback.
• To begin disc playback.
• To begin disc playback.
PLAY
RECORD
• To start a recording or
One Touch Recording.
REPEAT
RETURN
•To play a chapter or title
•To play a track or disc
repeatedly.
repeatedly.
•To return to the previous
•To return to the previous
operation in menu.
operation in menu.
SEARCH
MODE
•To search track.
•
To search chapter, title or time.
•To call up the index or time
•To search time.
•To set or search the markers.
search menu.
•To set or search the markers.
SETUP
•To call up the DVD setup
•To call up the DVD setup
menu.
menu.
SKIP/CH.
SKIP/CH.
• To change channels.
•
To adjust the tracking manually
during playback.
• To skip chapters.
• To skip tracks.
SLOW
• To view the tape
Keep in mind the following when
using the remote control:
Make sure that there is no obstacle
between the remote control and the
remote sensor on the unit.
in slow motion.
SPEED
•
•To select the recording speed.
•To turn the unit on or off.
STANDBY-ON
•To turn the unit on or off.
•To turn the unit on or off.
• The maximum operable ranges
from the unit are as follows.
- Beeline: approx. 23 feet (7m)
- Either side of the center:
approx. 16 feet (5m) within 30°
- Above: approx. 16 feet (5m)
within 15°
STOP
• To stop playback.
• To stop playback.
• To stop playback or recording.
SUBTITLE
T-SET
•To put the VCR into standby
•To select subtitles on a disc.
mode for a Timer Recording.
TOP MENU
VCR
•To call up the Top Menu
- Below: approx. 10 feet (3m)
within 30°
on a disc.
• To select the VCR output
mode.
• To activate the remote control
in VCR mode.
VCR/TV
ZOOM
• To select DVD position or
• To select CD position or TV
• To select VCR position or
TV position.
position.
TV position.
•To magnify part of a picture.
(x2/x4)
EN
–
–
10
VCR Functions
Playback
Before:
Turn on the TV and set it to
channel 3.
• If channel 3 is already occupied for broad-
casting, see “RF Output Channel” section.
4
OPEN/CLOSE
STANDBY-ON
/EJECT
SPEED
AUDIO
3 4 2
1
1
4
7
2
5
8
3
6
9
SKIP/CH.
VCR
STANDBY-ON
VCR/TV
SLOW
VCR
OPEN/
CLOSE
y
0
VCR
+1 0
DVD
To start
playback
1
3
2
4
DISPLAY
PAUSE
POWER-ON
REC
TIMER
VIDEO
AUDIO
R
Q
PN
O
X
Y
PLAY
REW
F.FWD STOP/EJECT PLAY RECORD
IR
CHANNEL
2
PLAY
STOP
3
RECORD
MENU
ENTER
To stop
playback
STOP
To eject
OPEN/CLOSE
/EJECT
Hint
• When a tape without record tab is inserted, the unit will start playback automatically.
• Tracking will be automatically adjusted upon playback. To adjust the tracking manually, press
[SKIP/CH. G/K H/L] (or [CHANNEL K/L]).
Other Operations
To cue or review picture during playback
Counter Reset
Hint
(Picture Search)
Press [g] or [h] ([F.FWD g] or [REW h]).
• Press it again and the unit will search in super high
speed. (in the SLP mode only)
Hit [CLEAR/C.RESET].
•
Still/Slow mode
will be automati-
cally cancelled
after 5 minutes
to prevent dam-
age to the tape
and the video
head.
To play back in slow motion
Hit [SLOW] during playback or the still mode.
• If the noise bars appear on the TV screen, you can
reduce it by pressing [SKIP/CH. G/K H/L] (or
[CHANNEL K/L]).
To freeze the picture on TV screen during play-
back (Still mode)
Hit [PAUSE k] . Each time you hit the button, the
• To return to
playback from
the Picture
Search/Still/
Slow mode, hit
[PLAY B].
Auto Rewind
picture will be forwarded by one frame.
•
If the picture begins to vibrate vertically during the still
mode, stabilize the picture by pressing
When a tape reaches its end during playback, fast-for-
ward or recording (except Timer Recording and One
Touch Recording), the tape will automatically rewind
to the beginning. After rewinding finishes, the unit will
eject the tape.
[SKIP/CH.
G
/
K
H
/
L
] (or [CHANNEL
/ ]).
K L
• If the picture is distorted or rolling vertically, adjust
the vertical hold control on your TV if equipped.
Index Search
SEARCH
MODE
3
1
TIME SEARCH
– : – –
To rewind
You can skip the program backward
and forward by the Index Mark.
ss
VCR
Hit twice.
VCR
To fast forward
• Insert a tape into this unit.
BB
SEARCH
MODE
1
INDEX SEARCH
2
Select the desired length of
time for fast forwarding or
rewinding.
– –
After searching,
Hit once.
4
PLAYB
TIME SEARCH
2 : 5 0
or
Hint
0:01~ 9:59
(1 minute~9 hours
and 59 minutes)
• The Index Mark will be made automatically
at the beginning of each recording.
2
INDEX SEARCH
• The time gap between Index Marks should
be greater then 1 minute for SP mode, 2
minutes for LP mode and 3 minutes for
SLP mode.
0 3
or
01 ~ 20
CURRENT PROGRAM
3
Time Search
Beginning
End of
the tape
of the tape
To rewind
You can search backward and for-
ward a specific length of time on a
Pro.1 Pro.2 Pro.3 Pro.4 Pro.5
02 01 01 02 03
INDEX MARK
ss
tape.
VCR
To fast forward
VCR
BB
• Insert a tape into this unit.
Hint for Index Search & Time Search
After searching,
• These functions are not available during recording.
• Hit [STOP C] to stop the search.
4
• If a tape ends during a search, your search will be cancelled and the tape will rewind to the
beginning.
PLAYB
EN
–
–
11
Auto Repeat
This function will playback a tape
repeatedly from the beginning
- M E N U -
1
MENU
TIMER PROGRAMMING
B AUTO REPEAT [OFF]
CHANNEL SET UP
CLOCK SET
LANGUAGE SELECT
when the tape reaches to the end.
VCR
2
- M E N U -
VCR
TIMER PROGRAMMING
B AUTO REPEAT [ON]
CHANNEL SET UP
CLOCK SET
LANGUAGE SELECT
or
Hint
•
•
To cancel Auto Repeat, follow steps 1)-2) above. Then, hit [B], so that [OFF] appears beside AUTO REPEAT. Hit [CLEAR/C.RESET] to exit.
If menu remains on the TV screen at step 3), hit [CLEAR/C.RESET] to exit.
Recording
Recording & OTR (One Touch Recording)
Before:
3
6
Turn on the TV and set it to
channel 3.
5 6 4 1
2
• If channel 3 is already occupied for
broadcasting, see “RF Output Channel” section.
OPEN/CLOSE
/EJECT
STANDBY-ON
STANDBY-ON
SPEED
AUDIO
OPEN/
N
y
CLOSE
VCR
1
4
7
2
5
8
3
6
9
POWER-ON
SKIP/CH.
VCR
REC
TIMER
VCR
D
VIDEO
AUDIO
R
Q
PN
O
X
VCR/TV
SLOW
Y
2
1
2
REW
F.FWD STOP/EJECT PLAY RECORD
IR
CHANNEL
SOURCE
0
VCR
+1 0
DVD
1
4
7
2
5
8
0
3
6
9
DISPLAY
PAUSE
SKIP/CH.
or
Accidental erasure prevention
PLAY
• Select the chan-
nel to record.
STOP
To prevent accidental recording on a
recorded cassette, remove its record tab.
To record on it later, cover the hole with
adhesive tape.
5
4
with tab
RECORD
MENU
ENTER
Tape Speed
Recording/Playback Time
3
SETUP TOP MENU
RETURN
Record tab
Type of tape
SP mode
T60
1hour
3hour
T120
2hours
6hour
T160
2-2/3hours
8hour
SPEED
SLP mode
You CAN NOT copy a DVD to a videotape.
• Select the desired
tape speed.
SP
RECORD
4
To stop recording temporarily (Pause mode)
Hit [PAUSE k].
REC
• During the rec-pause mode, five
represents one minute.
C
marks appear on the TV screen. Each
C
mark
Hit [RECORD] repeatedly to select the desired
recording length.
• Hit it again to resume recording.
• Pause mode will be automatically cancelled after 5 minutes to prevent damage to
the tape and the video head.
REC
OTR(0:30)
OTR(1:00).....
(Normal recording)
OTR(8:00)
OTR(7:30)
Hint
5
6
OPEN/CLOSE
/EJECT
• If you want to watch one channel while recording another.
1) Hit [VCR/TV] to put the unit in TV position.
STOP
2) Select a channel you want to watch with the TV, the cable box or the satellite box.
Timer Recording
•Insert a tape with its record tab
2
3
4
Select the desired month
PROGRAM NUMBER
DATE – – / – –
START TIME – – : – – – –
4
into the unit.
ONE TIME PROGRAM
VCR
or
PROGRAM NUMBER
1
END TIME – – : – – – –
DATE
1 0 / 0 3 MON
VCR
or
CHANNEL
– –
START TIME – – : – – – –
END TIME – – : – – – –
REC SPEED – –
- M E N U -
1
CHANNEL
– –
Select an empty program number.
MENU
B TIMER PROGRAMMING
AUTO REPEAT [OFF]
CHANNEL SET UP
CLOCK SET
REC SPEED – –
LANGUAGE SELECT
Select the desired day.
TIMER PROGRAMMING
PROGRAM NUMBER
1
• You can program one
year in advance.
or
PROG
12345678
B ONCE
DAILY
WEEKLY
DATE
START TIME
or
Availableprogram num-
Select “ONCE”, “DAILY”
(Mon-Fri), or “WEEKLY”.
ber flashes.
EN
–
–
12
ONE TIME PROGRAM
PROGRAM NUMBER
Hint
5
Select the desired start time
8
1
• To go back one step, hit [s] (during
(hour).
DATE
1 0 / 2 4 MON
START TIME 0 7 : 3 0 PM
END TIME 0 8 : 3 0 PM
steps 3) to 9) ).
ONE TIME PROGRAM
or
PROGRAM NUMBER
1
CHANNEL
1 6
DATE 1 0 / 2 4 MON
START TIME 0 7 : 3 0 – –
REC SPEED – –
To Check, Correct or Cancel a
Timer Program
1) Hit [SUBTITLE/T-SET] then, [VCR]
on the remote control.
2) Select main menu by hitting [MENU].
3) Select “TIMER PROGRAMMING”
by pressing [K/L]. Then, hit [B].
4) Select the program number which
you want to check by pressing
[K/L]. The details of the program
you selected will appear on the TV
screen.
or
END TIME – – : – – – –
CHANNEL
– –
Select the desired channel.
REC SPEED – –
• If you have connected the unit to a
cable box or satellite box as the
Connection on page 6, select the VCR
to channel 3 or 4 (the RF output chan-
nel of the VCR). Then, select the
desired channel at the cable box or
satellite box. Leave the cable box or
satellite box on for Timer Recording.
Select the minute.
or
• Go to the digit you want to
change by pressing [s/B]. Then,
enter correct numbers by press-
ing [K/L].
ONE TIME PROGRAM
9
PROGRAM NUMBER
DATE
1
1 0 / 2 4 MON
ONE TIME PROGRAM
PROGRAM NUMBER
6
7
START TIME 0 7 : 3 0 PM
END TIME 0 8 : 3 0 PM
• You may cancel the entire pro-
gram by hitting [s] while the pro-
gram number flashes.
1
or
CHANNEL
1 6
DATE
1 0 / 2 4 MON
REC SPEED SP
START TIME 0 7 : 3 0 PM
B SP
SLP
END TIME – – : – – – –
or
5) Hit [CLEAR/C.RESET] to exit.
6) Hit [SUBTITLE/T-SET] to return to
timer stand-by mode.
To cancel a Timer Recording
in progress
CHANNEL
– –
REC SPEED – –
Select the desired recording speed.
AM
B PM
• To set another program after step 9), hit [
Then, continue with step 2).
B
].
Select “AM” or “PM”.
CLEAR/
C. RESET
Hit [STOP/EJECT CA] on the unit.
Repeat the procedure in steps
5) and 6) to set the end time.
10
SUBTITLE
T-SET
•
The TIMER light on the
front panel appears.
The unit will change to
the DVD mode.
Hints for OTR and Timer Recording
• Hit [VCR] on the remote control before you set Timer Recording. Make sure the remote control is in the VCR mode,
then hit [SUBTITLE/T-SET].
• If a tape is not in the unit or does not have the record tab, the TIMER light flashes and Timer Recording cannot be
performed. Please insert a recordable tape.
• When Timer Recordings are set, the TIMER light will appear. To use the VCR as usual until the time for the recording, hit
[SUBTITLE/T-SET] so that the TIMER light disappears. Hit [VCR/TV] to choose the VCR position. Select either VCR or
DVD mode, then continue with the other features as described in this manual.
After an OTR or a Timer Recording has been set, this unit operates as follows:
• If a tape runs out before an OTR or a Timer Recording is finished, the unit ejects the tape and switches to the DVD mode
automatically. If the DVD power is off, the unit does not switch to the DVD mode but goes into the timer standby mode.
Press [SUBTITLE/T-SET] on the remote control or [STOP/EJECT C A] on the unit, then hit [VCR] to activate the VCR
function again.
• Once the unit turns to the timer standby mode, no VCR functions are available until [SUBTITLE/T-SET] is hit. ([SOURCE]
on the front panel and [VCR] on the remote control will not function.)
• To cancel the timer standby mode, press [SUBTITLE/T-SET] on the remote control or [STOP/EJECT C A] on the unit, then
hit [VCR] to activate the VCR function again.
• The mode of the unit and the remote control may differ (VCR mode or DVD mode) when you set Timer Recording or after
you cancelled Timer Recording. Press [VCR] or [DVD] on the remote control to select your desired mode before you
operate.
When an OTR or a Timer Recording is completed...
• If Auto Power Off for DVD has been activated and there are Timer Recordings on standby, the unit turns off automatically,
and the TIMER light appears to indicate the unit is in the timer standby mode.
• The TIMER light flashes if there are no more Timer Recordings on standby.
• If Auto Power Off for DVD has NOT been activated, the unit switches to the DVD mode and all the VCR function will be
unavailable. The TIMER light will not appear as long as the DVD is in use. All the DVD functions are available during OTR,
timer standby mode and Timer Recording.
If you want to use the DVD player during a Timer Recording or while the TIMER light appears or flashes.
• Hit [STANDBY-ON] to turn on the unit. Hit [DVD] on the remote control to choose DVD mode, then continue with the other
DVD features as described in this manual. You don’t need to set the TIMER off to use the DVD player.
NOTE (for Timer Recording) :
• If there is a power failure or the unit is unplugged for more than 30 seconds, clock and all timer settings will be lost.
EN
–
–
13
Copying a Video Tape
Warning: Unauthorized recordings of copyrighted video tapes may be an infringement of copyright laws.
(Back of TV)
(Back of another source)
(Back of Recording DVD/VCR*)
DVD/VCR
AUDIO OUT
VCR
2
AUDIO OUT
1
or
ANT-IN
L
Connect
AUDIO IN
Connect
R
R
VIDEO OUT
VIDEO OUT
VIDEO IN
ANT-OUT
RF cable
(supplied)
Audio/Video cables
*Front input jacks are also available
(not supplied)
1) Insert a pre-recorded tape into the playing VCR.
2) Insert a tape with its record tab into the recording unit.
3) Hit [SPEED] on the remote control of the recording unit to select the desired recording speed (SP/SLP).
4) Select the “L1”or “L2” position on the recording unit.
• To use the input jacks on the back of this unit, select “L1” position by pressing [0], [0], [1] on the remote control or
[CHANNEL K/L].
• To use the input jacks on the front of this unit, select “L2” position by pressing [0], [0], [2] on the remote control or
[CHANNEL K/L].
5) Hit [RECORD] on the recording unit.
6) Begin playback of the tape in another source.
7) To stop recording, hit [STOP/EJECT C A ] on the recording unit, then stop playback of the tape in another source.
Hint
• For best results during dubbing, use the front panel controls whenever possible. The remote control might affect another
source’s operation.
• Always use video-quality shielded cables with RCA-type connectors. Standard audio cables are not recommended.
• You can use a video disc player, satellite receiver or other audio/video component with A/V outputs.
• “L1” or “L2” is found before the lowest memorized channel. (Example: CH02)
• “L2” input jacks are on the front of this unit.
EN
–
–
14
DVD Functions
Playback
Before: Turn on the TV, amplifier and any other components which are connected to this unit. Make sure the TV and audio
receiver (commercially available) are set to the correct channel.
1 2 4 3
OPEN/CLOSE
/EJECT
STANDBY-ON
SPEED
AUDIO
DVD
1
1
DVD-V
CD
1
4
7
2
5
8
3
6
9
STANDBY-ON
SKIP/CH.
OPEN/
CLOSE
N
y
VCR/TV
SLOW
1
2
POWER-ON
REC
TIMER
VCR
DVD
P.SCAN
PLAY
VIDEO
AUDIO
0
+1 0
R
Q
PN
O
U
P
O
T
X
Y
OPEN/CLOSE
/EJECT
DISPLAY
VCR
DVD
PAUSE
STANDBY-ON
REW
F.FWD STOP/EJECT PLAY RECORD
IR
CHANNEL
SOURCE
PREV
STOP
PLAY
NEXT
3
4
Hint
PLAY
STOP
1
Insert a disc with
label facing up.
RECORD
3
4
• A “prohibited icon” may appear at the top-right on the TV screen when the operation is prohibited
by the disc or this unit.
• Some DVDs may be played from title 2 or 3 due to specific programs.
• During the playback of a two-layered disc, pictures may stop for a moment. This happens while the
1st layer is being switched to the 2nd layer. This is not a malfunction.
To start
To stop
playback
STOP
playback
PLAY
TIP:
You can change the on-screen language for DVD function in “PLAYER MENU” setting (Refer to page 20).
DVD menu
Fast Forward/Reverse Search
DVD
Some discs contain menus which allow you to customize
DVD playback. Press [K / L / s / B]to select an item, then
press [ENTER] (or [PLAY B]), to select.
E
1
DVD-V
CD
Press [h] or [g]
repeatedly during playback to select the required
forward or reverse speed.
To continue playback, hit [PLAY B].
Calling up a Menu Screen during Playback
• Hit [MENU] to call up the DVD menu.
• Hit [TOP MENU] to call up the title menu.
Hint
Hint
•
For DVDs, fast forward or reverse search speed is different depending
on the disc. Approximate speed is 1(x2), 2(x8), 3(x20), 4(x50), 5(x100)
• Menu operations may vary depending on the disc. Refer to the
.
manual accompanying the disc for details.
• For Audio CDs, approximate speed is 1(x2), 2(x8), 3(x30).
Resume
Slow Forward/Slow Reverse
DVD
DVD
DVD-V
CD
DVD-V
Hit [STOP C] duing playback.
Resume message will appear on
the TV screen.
Press [h] or [g] repeatedly during the
pause mode to select the required forward or
reverse speed.
Resume ON
1
Press 'PLAY' to play from here.
To play the beginning,
press 'STOP' first and then 'PLAY'.
Hit [PLAY B], playback will
resume from the point at which
playback was stopped.
To continue playback, hit [PLAY B].
Hint
• Slow forward or reverse speed is different depending on the disc.
Hint
Approximate speed is 1(1/16), 2(1/8), 3(1/2).
• Set “STILL MODE” to “FIELD” in the Display menu if pictures in the
slow playback mode are blurred. (Refer to pages 20-21.)
• To cancel resume, hit [STOP C] one more time during the Stop
mode.
• The resume information stays on even when the power is turned off.
Zoom
DVD
Paused and Step-by-Step Playback
DVD-V
DVD
1) Hit [ZOOM] during playback.
DVD-V
CD
2) Hit [ZOOM] repeatedly to select the required zoom factor:
x2, x4 or OFF.
Hit [PAUSE k] during playback.
To continue playback, hit [PLAY B].
x2
x4
DVD-V
The disc goes forward by one frame each time [PAUSE k] is
hit during the pause mode.
To continue playback, hit [PLAY B].
3) Press [K / L / s / B] to slide the zoomed picture across
the screen.
4) To exit zoom mode, hit [ZOOM] to select OFF.
Hint
• On DVDs, set “STILL MODE” to “FIELD” in the Display menu if pictures in the
Hint
pause mode are blurred. (Refer to pages 20-21.)
• Zooming function does not work while the disc menu is showing up.
To use [PREV h], [NEXT i] on the Main Unit
• x4 zoom is not available on some discs.
• The picture may be distorted when you press [PAUSE k] or [h]
repeatedly in the zoom mode.
DVD-V
CD
• It may take several seconds to slide the zoomed picture.
Hit once to skip chapters or tracks to a desired point.
Press and hold to change forward or reverse playback speed.
EN
–
–
15
On-Screen Display
You can check the information about the current disc by hitting [DISPLAY] on the remote control.
DVD
DVD
CD
DVD-V
DISPLAY
Angle icon, appears only when avail-
able on the DVD
DISPLAY
Current playback status
4/12 0:03:21 - 0:02:15
T
Current playback status
1
Remaining time of the current track
Elapsed time of the current track
TR(Track):
Current track number / Total tracks
11/16 0:00:00 - 0:03:30
1
Remaining time of the current chapter
Elapsed time of the current chapter
DISPLAY
CH(Chapter):
ALL:
Current track number / Total tracks
Current chapter number / Total chapters
DISPLAY
4/12 0:13:45 - 0:45:40
T
2
Current repeat setting appears only
when the repeat setting is active
T: Track repeat
1/3 0:00:00 - 1:23:45
2
3
A: All Tracks repeat
Remaining time of the current title
Elapsed time of the current title
A
B: A-B repeat
Remaining time of the entire disc
Elapsed time of the entire disc
DISPLAY
TT(Title):
Current title number / Total titles
DISPLAY
3
T
L1
Hint
Layer numbers, appears only when
playing a two-layered Disc
L0: Layer 0 is playing
• When you are playing a disc in PROGRAM or RANDOM mode,
2
PROGRAM (or RANDOM) will be displayed instead of
.
L1: Layer 1 is playing
Current repeat setting appears only
when the repeat setting is active
C: Chapter repeat / T: Title repeat /
A
B: A-B repeat
BIT RATE: The amount of audio and
video data currently being read
DISPLAY
4
EN
–
–
16
Search Function
Track Search
Title / Chapter Search
Time Search
DVD
DVD
DVD
CD
DVD-V
DVD-V
CD
Using [SEARCH MODE]
Using [SEARCH MODE]
1
PLAY
TOTAL 1:29:00
1
1
SEARCH
MODE
/12
/29
PLAY
SEARCH
MODE
Hit repeatedly until
the Time Search dis-
play appears.
Hit once for the
SEARCH
MODE
Chapter Search.
Hit twice for the Title
Search.
2
1
4
7
2
5
8
0
3
6
/29
2
1
4
7
2
5
8
0
3
6
9
9
1
2
5
8
0
3
6
TOTAL 1:29:00
2
+1 0
Within 30 seconds
/12
4
7
9
Within 30 seconds
+1 0
• For the disc with less than 10 tracks,
hit the track number directly.
Within 30 seconds
• For discs with more than 10 but less
than 99 tracks, to play single-digit
track, hit [0] first, then the track num-
ber (e.g. for track 3, hit [0], [3]). To
play a double-digit track, hit the track
number.
Hint
H
G
Using [SKIP
1
,
]
• When there is no need to enter a number,
“0” appears automatically.
Current Chapter
(CH)
For example, “0: 0_: __” appears in the
Time Search display if the total time of the
title or track is less than 10 minutes.
• Hit [CLEAR/C.RESET] to erase the incor-
rect input at step 2).
PLAY
CH 1 CH 2 CH 3 CH 4
SKIP
SKIP
H
G
Using [SKIP
,
]
or
1
Current Title
(TT)
Current Track
(TR)
PLAY
SKIP/CH.
TT 1 TT 2 TT 3 TT 4
TR 1 TR 2 TR 3 TR 4
SKIP
SKIP
SKIP
SKIP
(If the disc has no chapters)
SKIP/CH.
Hint
• Depending on the disc being played, this
function can also be performed by directly
entering the desired chapter number with
the Number buttons. Refer to the manual
accompanying the disc.
• For CDs, Track Search is not available for
Programmed or Random Playback.
Hint
• [+10] button can also bring the Track
Search display, except for the disc with
less than 10 tracks. For such a disc, track
search can be done by just hitting the track
number.
Marker Setup
DVD
To return to the marker
later
1
To exit the marker screen
DVD-V
CD
This feature allows you to assign a spe-
cific point on a disc to be called back
later.
1
RETURN
PLAY
To set a marker
1
Hint
SEARCH
Hit repeatedly until
this marker display
appears.
MODE
PLAY
• The Marker display will disappear in about
30 seconds when there is no output.
• To clear a marker, select the marker to be
cleared at step 2) in the section “To set a
marker” or “To return to the marker later”
and then hit [CLEAR/C.RESET].
SEARCH
MODE
Hit repeatedly until
this marker display
appears.
2
or
• Opening the disc tray or turning off the
power will erase all markers.
2
• Selecting “AC” at step 2) in the section “To
set a marker” or “To return to the maker
later” will also erase all markers.
or
3
ENTER
3
at the desired marker
ENTER
• Playback will restart from the specific
point which you set.
EN
–
–
17
Repeat / Random / Programmed Playback
Repeat Playback
Repeat A-B Playback
Programmed Playback
DVD
DVD
DVD
DVD-V
CD
DVD-V
CD
CD
You may determine the order in which
tracks will play.
1
Repeat function is available only during
playback.
PLAY
A-
1
1
STOP
A-B
PLAY
TOTAL 0:00:00
at your desired starting point (A)
MODE
ENTER
REPEAT
2
A-B
A-B
Hit once.
Each time you hit [REPEAT], repeat
function changes as example below.
2
at your desired end point (B)
TOTAL 1:03:30
1
5
3:30
5:10
DVD-V
10 4:20
11 3:00
12 3:20
17 4:10
22 2:50
2/3
or
•
Point B should be in the same title
or track as point A.
(current chapter repeat)
CHAPTER
1/4
Hint
(current title repeat)
TITLE
OFF
• Up to 99 tracks can be
ordered.
• If eight or more tracks
were in a program, use
[SKIP/CH. H/K G/L]
to see all the tracks.
• To exit the sequence, hit [A-B] so that
ENTER
OFF appears.
(repeat off)
•
To cancel Point A, hit [CLEAR/C.RESET].
• This function does not work in the other
repeat modes.
CD
(current track repeat)
(entire disc repeat)
(repeat off)
TRACK
ALL
3
Random Playback
PLAY
This function shuffles the playing order
of tracks instead of playback in the
OFF
sequence.
DVD
Hint
Hint
CD
• Hit [CLEAR/C.RESET] at step 2) to erase
• Repeat setting will be cleared when mov-
1
the most recently entered track.
ing to another title, chapter or track.
• Repeat playback are not available with all
discs or during repeat A-B playback.
STOP
RANDOM
• To erase all programmed tracks at once,
select “ALL CLEAR’’ and hit [ENTER] at
step 2).
CD-DA
TOTAL 0:45:55
RANDOM PROGRAM
--no indication--
• While a program is being played back,
MODE
PLAY
[STOP C] works as follows;
⇒
Hit [STOP C] and [PLAY B] next, so
that the programmed playback restarts.
(CD playback restarts from the current
point.)
Hit twice.
2
⇒
Hit [STOP C] twice and [PLAY B] next,
so that playback restarts from the first
track in the original order. However, your
programmed playback can be restarted
when you follow the above steps. (Your
programs are still stored until either the
disc tray is open or power is turned off.)
PLAY
Hint
• To repeat the current track in the random
selections, hit [REPEAT] repeatedly until
TRACK appears during playback.
• To repeat the current track in the program,
hit [REPEAT] repeatedly until “
TRACK’’
appears during playback.
• To repeat the entire random selections, hit
[REPEAT] repeatedly until
appears during playback.
ALL
• To repeat the entire program, hit
[REPEAT] repeatedly until “
ALL’’
appears during playback.
EN
–
–
18
Special Settings
Subtitle Language
Audio Language
Stereo Sound Mode
DVD
DVD
DVD
DVD-V
DVD-V
CD
This unit allows you to select a subtitle
language (if available) during DVD play- language (if multiple languages are
This unit allows you to select an audio
This unit allows you to select a sound
mode during CD playback.
back.
available) during DVD playback.
1
1
1
PLAY
PLAY
PLAY
STEREO
1.ENG/6
1.ENG Dolby D 3/2.1ch 48k/3
AUDIO
AUDIO
SUBTITLE
T-SET
Each time you hit [AUDIO], audio
Each time you hit [SUBTITLE/T-SET],
subtitle language changes as example
below.
Each time you hit [AUDIO], sound
language changes as example below.
mode changes as example below.
(English audio)
(Spanish audio)
ENG
SPA
(right and left channels
are active)
STEREO
L-ch
(English subtitles)
ENG
(left channel is active)
(French subtitles)
FRE
(right channel is active)
R-ch
(French audio)
FRE
Virtual Surround
OFF
(no subtitles)
Camera Angle
DVD
DVD-V
CD
DVD
To set subtitle ON/OFF
1
DVD-V
You can enjoy stereophonic virtual
world on your existing 2 channel stereo
system.
Some DVD discs may con-
tain scenes which have
been shot simultaneously
from various angles. You can change
the camera angle if the
PLAY
1.ENG/6
1
SUBTITLE
T-SET
PLAY
OFF
icon
appears on the screen. If the “ANGLE
ICON” setting is “OFF” in the OTHERS
MODE
menu, the
icon will not appear.
2
(Refer to pages 20-22.)
OFF
Hit twice (once for CD)
1
PLAY
2
1 / 8
ENTER
1
Hint
ANGLE
• If your language is not shown after press-
ing [AUDIO] or [SUBTITLE/T-SET] several
times, the disc may not have that lan-
guage. However, some discs allow audio
language or subtitle language setting on
the disc menu. (Operation varies depend-
ing on the discs, so refer to the manual
along with the disc.)
1: Natural effect
2: Emphasized effect
OFF: No effects (original sound)
Black Level Setting
DVD
3
RETURN
DVD-V
• When “NOT AVAILABLE” appears on the
TV screen, it means no subtitle is recorded
on the scene.
• If you choose a language that has three-
letter-language code, the code will be dis-
played every time you change the subtitle
language setting. If you choose any other
languages, ‘---’ will be displayed instead.
(Refer to page 24.)
Adjust the Black Level Setting to make
the dark areas of the TV picture brighter.
Hint
1
ON
For CD play back only
PLAY
• Virtual Surround will not be effective if the
sound mode is set to something other than
STEREO. Refer to “Stereo Sound mode”.
MODE
2
OFF
ENTER
ON: Makes the dark areas brighter.
OFF: Shows the original picture as recorded.
3
RETURN
EN
–
–
19
DVD
DVD Setup
QUICK SETUP Menu
You can select the “PLAYER MENU”, “TV ASPECT”, or “DOLBY DIGITAL” from the QUICK SETUP menu quickly.
1
2
SETUP
STOP
or
Select the desired item.
<SETUP MENU>
Confirm that “QUICK” is selected.
ENTER
SETUP
QUICK
SETUP
A
B
C
P20
P21
P21
Step 5)
Step 5)
Step 5)
PLAYER MENU
TV ASPECT
DOLBY DIGITAL
ENGLISH
4:3 LETTER BOX
BITSTREAM
QUICK
CUSTOM
INITIALIZE
ENTER
•
Refer to the sections “PLAYER
MENU”, “TV ASPECT”, or “DOLBY
DIGITAL” section on page 20 or 21.
CUSTOM Menu
You can change the settings of the unit.
QUICK
on pages 20-22 indicates DVD Setup menus also accessible from the QUICK SETUP menu.
•
ENTER
SETUP
1
2
3
STOP
or
or
<SETUP MENU>
Select “CUSTOM”.
Select the desired item.
ENTER
SETUP
SETUP
SETUP
CUSTOM
LANGUAGE
DISPLAY
AUDIO
PARENTAL
OTHERS
QUICK
CUSTOM
INITIALIZE
QUICK
CUSTOM
INITIALIZE
LANGUAGE menu
DISPLAY menu
AUDIO menu
PARENTAL menu
OTHERS menu
SETUP
LANGUAGE
SETUP
AUDIO
SETUP
PARENTAL
SETUP
OTHERS
SETUP
DISPLAY
PASSWORD
AUDIO
ORIGINAL
OFF
ENGLISH
ENGLISH
DRC
DOWN SAMPLING ON
DOLBY DIGITAL BITSTREAM
ON
ANGLE ICON
AUTO POWER OFF ON
ON
TV ASPECT
STILL MODE
4:3 LETTER BOX
AUTO
Please enter a 4-digit password.
SUBTITLE
DISC MENU
PLAYER MENU
page 20
page 21
page 21
page 22
page 22
A
B
C
D
E
LANGUAGE Setting
A
Follow step 1) to 3) in the “CUSTOM Menu” section on above.
Select the desired language.
Select the desired item.
4
5
6
To exit the menu
ENTER
ENTER
SETUP
or
or
AUDIO ∗1 ∗2
(Default: ORIGINAL)
Sets the audio language.
AUDIO
Hint
∗1
ORIGINAL
ENGLISH
FRENCH
• Language options are not available
LANGUAGE menu
with some discs.
SUBTITLE: ∗1 ∗2
(Default: OFF)
Sets the subtitle language.
SUBTITLE
OFF
ENGLISH
FRENCH
• If OTHER is selected on the AUDIO,
SUBTITLE or DISC MENU screen,
press four-digit number to enter the
code for the desired language. (Refer
to the language code list on page 24.)
• Only the languages supported by the
disc can be selected.
SETUP
LANGUAGE
AUDIO
ORIGINAL
SUBTITLE
DISC MENU
PLAYER MENU
OFF
ENGLISH
ENGLISH
DISC MENU: ∗1
(Default: ENGLISH)
Sets the language for
DVD menu.
DISC MENU
ENGLISH
FRENCH
SPANISH
∗2
•
Language Setting for Audio and Subtitle
are not available with some discs. Then
use [AUDIO] and [SUBTITLE/T-SET].
Details are on page 19.
PLAYER MENU
ENGLISH
FRANÇAIS
ESPAÑOL
QUICK
PLAYER MENU:
(Default: ENGLISH)
Sets the language for
the On-screen display.
EN
–
–
20
DISPLAY Setting
B
You can change the display functions. Follow step 1) to 3) in the “CUSTOM Menu” section on page 20.
4
5
Select the desired item.
6
To exit the menu
SETUP
QUICK
TV ASPECT:
(Default: 4:3 LETTER BOX)
See Hint to the right.
Select the
desired
setting.
or
TV ASPECT
ENTER
Hint
TV ASPECT:
TV ASPECT
STILL MODE
4:3 LETTERBOX
AUTO
4:3 LETTER BOX
4:3 PAN & SCAN
16:9 WIDE
or
• Select “4:3 LETTER
BOX”, so that black bars
may appear on the top
and bottom of the screen.
DISPLAY menu
ENTER
SETUP
DISPLAY
• Select “4:3 PAN & SCAN”
TV ASPECT
STILL MODE
4:3 LETTER BOX
AUTO
STILL MODE:
(Default: AUTO)
See Hint to the right.
for a full height picture
Select the
desired
setting.
with both sides adjusted.
• Select “16:9 WIDE” if a
wide-screen TV is con-
nected to this unit.
STILL MODE:
• Select “AUTO” usually.
STILL MODE
ENTER
TV ASPECT
STILL MODE
4:3 LETTERBOX
AUTO
AUTO
FIELD
FRAME
or
• If you select AUTO, auto-
matically select the best
resolution setting
ENTER
(FRAME or FIELD)
based on the datacharac-
teristics of the pictures.
(default).
• If you select “FIELD”, the
picture in the still mode
will be stabilized.
• If you select “FRAME”,
the picture in the still
mode will be highly
defined.
• An individual picture on
TV screen is called as
“frame”, which consists of
two separate images
called as “field”.
Some pictures may be
blurred at the AUTO set-
ting instill mode due to
their data characteristics.
AUDIO Setting
C
Choose the appropriate audio settings for your equipment. It only affects during the playback of DVD discs. Follow step 1) to
3) in the “CUSTOM Menu” section on page 20.
5
4
6
To exit the menu
Select the desired item.
SETUP
DRC (Dynamic Range Control):
(Default: ON)
Set to “ON” to compress the range between soft and loud sounds.
or
DRC
ON
OFF
DOWN SAMPLING ON
ON
BITSTREAM
ENTER
DOLBY DIGITAL
BITSTREAM
AUDIO menu
Hint
DRC:
DOWN SAMPLING:
(Default: ON)
SETUP
AUDIO
• This function is available
only on the discs which
are recorded in the Dolby
Digital format.
Set to “ON” when outputting in 48kHz.
Set to “OFF” when outputting the original sound.
DRC
ON
DOWN SAMPLING ON
DOLBY DIGITAL BITSTREAM
DOWN SAMPLING:
DRC
ON
ON
OFF
BITSTREAM
DOWN SAMPLING ON
DOLBY DIGITAL
• When playing disc with
copyright Protection, the
sound will be down sam-
pled at 48kHz, even if
you set to “OFF”.
BITSTREAM
ENTER
QUICK
DOLBY DIGITAL:
(Default: BITSTREAM)
Set to “BITSTREAM” when the unit is connected to a Dolby Digital receiver.
• BITSTREAM: Outputs a Dolby Digital Signals.
• This function is avail-
able only on digital out-
putting of a disc
recorded in 96kHz.
• PCM: Convert the Dolby Digital into PCM (2 channel).
DRC
DOWN SAMPLING ON
DOLBY DIGITAL BITSTREAM
ON
ON
ON
PCM
ENTER
EN
–
–
21
PARENTAL Setting
D
Parental Control limits the disc viewing that exceed your settings. (An incorrect password will not play.)
This feature prevents your children from viewing inappropriate materials.
Parental Levels
Parental Level allows you to set the rating levels of your DVD discs. Playback will stop if the ratings exceed the levels you set.
Follow steps 1) to 3) in the “CUSTOM Menu” section on page 20.
To exit
the menu
4
Enter your desired four-
digit password (except
for 4737).
5
6
Select “PARENTAL
LEVEL”.
Select the
desired level.
7
SETUP
1
4
7
2
5
8
0
3
6
9
or
or
ENTER
ENTER
ENTER
PARENTAL LEVEL
ALL
PARENTAL LEVEL
PASSWORD CHANGE
ALL
8
7 [NC-17]
6 [R]
PARENTAL menu
SETUP
PARENTAL
CONTROL LEVELS
PASSWORD
• ALL:
All parental locks are cancelled.
Please enter a 4-digit password.
• Level 8:
DVD softwares of any grades (adult/general/children) can be played back.
• Levels 7 to 2: Only DVD softwares intended for general use and children can be played
back.
• Level 1:
Only DVD softwares intended for children can be played back, with those
or
intended for adult and general use prohibited.
If you have set a password
already, enter the current four-
digit password.
TIPS FOR LEVELS
• 7 [NC-17]:
• 6 [R]:
• 4 [PG13]:
• 3 [PG]:
• 1 [G]:
No one under 17 admitted
Restricted; under 17 requires accompanying parent or adult guardian
Unsuitable for children under 13
Parental Guidance suggested
General Audience
SETUP
PARENTAL
PASSWORD
Enter current password.
Hint
• DVD-Video discs may not respond to the parental lock settings. Make sure this function
works with your DVD-Video discs.
To Change the Password for Parental Controls
You can change your password for parental controls. Follow steps 1) to 3) in the “CUSTOM Menu” section on page 20.
To exit
the menu
4
5
6
Select “PASSWORD
CHANGE”.
Enter your new
four-digit password
(except for 4737).
7
Enter your desired four-
digit password (except for
4737).
SETUP
or
1
4
7
2
5
8
0
3
6
9
1
4
7
2
5
8
0
3
6
9
ENTER
ENTER
PARENTAL LEVEL
PASSWORD CHANGE
ALL
Hint
PARENTAL menu
• Record the password
SETUP
PASSWORD
Please enter a 4-digit password.
PARENTAL
in case you forget it.
SETUP
PARENTAL
•
•
If you forget the password, hit
[4], [7], [3], [7] at step 4), then
enter your new password.
Password will be cleared
and parental levels will
be set to “ALL”.
PASSWORD
Enter current password.
OTHERS Setting
E
You can change the other functions. Follow steps 1) to 3) in the “CUSTOM Menu” section on page 20.
4
5
Select the desired item.
6 To exit the menu
SETUP
ANGLE ICON:
(Default: ON)
Set to “ON” to show the angle icon when multiple camera
angles are available during DVD playback.
or
OFF
ON
ANGLE ICON
AUTO POWER OFF ON
ON
OTHERS menu
ENTER
SETUP
OTHERS
AUTO POWER OFF:
(Default: ON)
ANGLE ICON
AUTO POWER OFF
ON
ON
Set to “ON” to turn this unit off automatically
after 30 minutes of no use.
ANGLE ICON
ON
ON
AUTO POWER OFF ON
OFF
ENTER
EN
–
–
22
Reset to the Default Setting (Except for PARENTAL Setting)
To exit
the menu
1
2
3
4
or
or
SETUP
STOP
SETUP
ENTER
ENTER
Select “YES”.
Select “INITIALIZE”.
<SETUP MENU>
Hit
twice.
SETUP
SETUP
INITIALIZE
Hint
• When you cancel to
initialize at step 3),
select “NO”.
SETUP
QUICK
CUSTOM
INITIALIZE
Initialize?
NO
YES
QUICK
CUSTOM
INITIALIZE
Information
Troubleshooting Guide
If this unit does not perform properly when operated as instructed in this Owner's Manual, check this unit consulting the following checklist.
PROBLEM
CORRECTIVE ACTION
• Make sure the power plug is connected to an AC outlet.
• Make sure the power is turned on.
• Check if the power plug is connected to an AC outlet.
• Check the batteries in the remote control.
D
V
D
No power.
This unit does not respond to
the remote control.
• Aim the remote control directly at the remote sensor. If necessary, remove all the obstacles
between the sensor and the remote control.
V
C
R
• You have to be within 23 feet of this unit.
• Check if the right mode is selected. If it’s not in the right mode, press [DVD] or [VCR],
whichever you need, on the remote control.
• Check if a cassette tape is in this unit.
• Tune your radio to an empty AM station so that you hear a lot of noises. Turn the volume up,
then if you hear some signal sound from the radio in response to your pressing buttons on
the remote control, the remote control is working.
Poor picture or noise.
• Interference signal may be received. Change the position and orientation of the unit.
Timer Recording is impossible.
• Make sure the Timer Recording is set correctly.
V
C
R
• Make sure the
light appears on the unit. If not, hit [SUBTITLE/T-SET].
TIMER
• Make sure the VCR clock is set correctly.
Cannot go into record mode.
• Make sure the tape has a record tab. If needed, cover the hole with adhesive tape.
•
Activate this unit in VCR mode. Hit [VCR] on the remote control so that the VCR OUTPUT light is lit.
Playback picture is partially noisy. • Adjust tracking control for a better picture by pressing [CHANNEL L/K] on the unit or
[SKIP/CH.G /K H /L] on the remote control.
Cannot view a tape but the
audio is OK.
• Head cleaning may be necessary. Refer to “AUTO HEAD CLEANING”.
• Make sure the VCR is not in the Menu mode.
No or poor, playback picture.
• Change the RF output channel to CH4. Then select the same channel on the TV.
• Fine tune your TV.
TV programs cannot be seen
normally.
• Re-check the ANT-IN and ANT-OUT connections. See pages 1 and 6.
• Hit [VCR/TV].
• Hit [VCR] on the remote control to activate it in the VCR mode. Check if the VCR OUTPUT
light is lit, then set it to the TV position by hitting [VCR/TV].
Video or color fades in and out when • You cannot copy a copyrighted video tape. You are experiencing copy guard protection.
making a copy of a video tape.
Cannot remove the tape.
No picture.
•
Check if this unit is in the VCR mode. If not, hit [VCR] on the remote control to switch the mode.
• Connect the video cables firmly.
D
V
D
• Insert a correct video disc that plays on this unit.
•
•
Hit [DVD] on the remote control. Check if the DVD OUTPUT light is lit. Then try other DVD features.
Set PROGRESSIVE correctly. Turn it on only if your TV has Progressive Scan and you are using the Component
Video connections between the unit and the TV. Disable Progressive Scan for all other connections. (See page 7.)
Disc cannot be played.
No sound.
• Insert the disc.
• Clean the disc.
• Place the disc correctly with the label side up.
• Cancel the parental lock or change the control levels.
•
Handle a disc with special care so that it does not have fingerprints, scratches, or dusts on its surface.
• Connect the audio cables firmly.
• Turn the power of the audio component on.
• Correct the audio output settings.
• Correct the input settings on the audio component.
No DTS audio is output.
Distorted picture.
• This unit does not support DTS audio. This is not a malfunction.
• Connect this unit directly to the TV.
•
There are some cases where pictures may be slightly distorted, and those are not a sign of a malfunction.
• Although pictures may stop for a moment, this is not a malfunction.
• Check if the INTERLACE/PROGRESSIVE mode is set correctly. See page 7.
Audio or subtitle language
does not match the setup.
• The selected language is not available for audio or subtitles on the DVD.
This is not a malfunction.
The camera angle cannot be changed.
•
The DVD does not contain sequences recorded from different camera angles. This is not a malfunction.
Audio or subtitle language
cannot be changed.
• The DVD does not contain audio source or subtitles in the selected language.
This is not a malfunction.
“Prohibited icon” appears on the • That operation is prohibited by this unit or the disc.
screen, prohibiting an operation. This is not a malfunction.
•
Some functions are not available in specific modes, but this is not a malfunction. Read the description in this Owner’s Manual for details on correct operations.
• Playback from a desired track and random playback are not available during program playback.
• Some functions are prohibited on some discs.
EN
–
–
23
Specifications
• Designs and specifications are subject
to change without notice.
• If there is a discrepancy between lan-
guages, the default language will be
English.
Video Heads :
Operating temperature :
41°F (5°C) to 104°F (40°C)
Dimensions :
W : 17-3/16"(435mm)
H : 3-3/4" (94mm)
D : 9-3/16" (233mm)
Weight :
Four Heads
Output signal format :
NTSC color
Power source :
120 V AC +/- 10%, 60 Hz +/- 0.5%
Power consumption :
21W (standby: 3.8W)
Approx 6lbs (2.7kg)
Language List
Language
Code
Language
French [FRE]
Frisian
Galician
Georgian
German [GER]
Greek [GRE]
Greenlandic
Guarani
Gujarati
Hausa
Hebrew
Hindi
Hungarian [HUN]
I-K
Icelandic [ICE]
Indonesian
Interlingua
Interlingue
Inupiak
Irish [IRI]
Italian [ITA]
Japanese [JPN]
Javanese
Kannada
Kashmiri
Kazakh
Kinyarwanda
Kirghiz
Kirundi
Code
Language
Macedonian
Malagasy
Malay
Code
Language
Siswat
Slovak
Slovenian
Somali
Code
A-B
5264
5271
5358
5747
5051
5158
5758
5360
5367
5447
5569
5455
5467
5957
5953
5965
5958
5966
5955
5964
5961
5960
6047
6051
6061
6565
6557
6558
6561
5165
6567
6569
6568
Abkhazian
Afar
Afrikaans
Albanian
Amharic
Arabic
Armenian
Assamese
Aymara
Azerbaijani
Bashkir
Basque
4748
4747
4752
6563
4759
4764
5471
4765
4771
4772
4847
5167
4860
5072
4854
4855
4864
4853
5971
4851
Malayalam
Maltese
Maori
Spanish [SPA]
Sundanese
Swahili
Marathi
Moldavian
Mongolian
Nauru
Swedish [SWE]
T
Tagalog
Tajik
Tamil
Tatar
Telugu
Thai
Tibetan
Tigrinya
Tonga
Tsonga
Turkish [TUR]
Turkmen
Twi
6658
6653
6647
6666
6651
6654
4861
6655
6661
6665
6664
6657
6669
Nepali
Norwegian [NOR]
O-R
Occitan
Bengali;Bangla
Bhutani
Bihari
6149
6164
6159
6247
6265
5247
6258
6266
6367
6459
6461
6467
5565
5560
5547
5551
5557
5347
5566
5647
5669
5760
5765
5757
6469
5771
6460
5761
5767
Oriya
Oromo(Afan)
Panjabi
Pashto;Pushto
Persian
Polish
Portuguese [POR]
Quechua
Rhaeto-Romance
Romanian [RUM]
Russian [RUS]
S
Samoan
Sangho
Sanskrit
Bislama
Breton
Bulgarian
Burmese
Byelorussian
C-E
Cambodian
Catalan
5759
4947
7254
4961
5464
4965
5047
6058
5160
5161
5166
U-Z
Ukrainian
Urdu
Uzbek
Vietnamese
Volapuk
Welsh
Wolof
Xhosa
Yiddish
Yoruba
Zulu
6757
6764
6772
6855
6861
4971
6961
7054
5655
7161
7267
Chinese [CHI]
Corsican
Croatian
6559
6553
6547
5350
6564
6554
6566
6660
6560
6550
6555
Czech
Danish [DAN]
Dutch [DUT]
English [ENG]
Esperanto
Estonian
Korean [KOR]
Kurdish
Scots Gaelic
Serbian
Serbo-Croatian
Sesotho
L-N
Laothian
Latin
Latvian;Lettish
Lingala
Lithuanian
5861
5847
5868
5860
5866
F-H
Setswana
Shona
Sindhi
Faroese
Fiji
Finnish [FIN]
5261
5256
5255
Singhalese
If you choose a Language that has a 3 letter language code, the code will be displayed every time you change the Audio or Subtitle language setting on page 19. If
you choose any other languages, ‘---’ will be displayed instead. (3 letter language code is written in bracket.)
LIMITED WARRANTY
FUNAI CORP. will repair this MAGNAVOX product, free of charge in the USA
in the event of defect in materials or workmanship as follows:
FUNAI CORP. AND ITS REPRESENTATIVES OR AGENTS SHALL IN NO
EVENT BE LIABLE FOR ANY GENERAL, INDIRECT OR CONSEQUEN-
TIAL DAMAGES ARISING OUT OF OR OCCASIONED BY THE USE OF
OR THE INABILITY TO USE THIS PRODUCT. THIS WARRANTY IS MADE
IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, AND OF
ALL OTHER LIABILITIES ON THE PART OF FUNAI, ALL OTHER WAR-
RANTIES INCLUDING THE WARRANTY OF MERCHANTABILITY, AND
FITNESS FOR A PARTICULAR PURPOSE, ARE HEREBY DISCLAIMED
BY FUNAI AND ITS REPRESENTATIVES IN THE UNITED STATES. ALL
WARRANTY INSPECTIONS AND REPAIRS MUST BE PERFORMED BY A
FUNAI AUTHORIZED SERVICE CENTER. THIS WARRANTY IS VALID
WHEN THE UNIT IS CARRIED-IN TO FUNAI AUTHORIZED SERVICE
FACILITY.
DURATION:
PARTS:
FUNAI CORP. will provide parts to replace defective parts
without charge for one (1) year from the date of original retail
purchase. Certain parts are excluded from this warranty.
LABOR:
FUNAI CORP. will provide the labor without charge for a peri-
od of ninety (90) days from the date of original retail pur-
chase.
LIMITS AND EXCLUSIONS:
This warranty is extended only to the original retail purchaser. A purchase
receipt or other proof of original retail purchase will be required together with
the product to obtain service under this warranty.
IMPORTANT:
THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS. YOU
MAY HAVE OTHER RIGHTS THAT VARY FROM STATE TO STATE. IF, AT
ANY TIME DURING THE WARRANTY PERIOD, YOU ARE UNABLE TO
OBTAIN SATISFACTION WITH THE REPAIR OF THIS PRODUCT, PLEASE
CONTACT FUNAI CORP.
This warranty shall not be extended to any other person or transferee.
This warranty is void and of no effect if any serial numbers on the product are
altered, replaced, defaced, missing or if service was attempted by an unau-
thorized service center.This MAGNAVOX Limited warranty does not apply to
any product not purchased and used in the United States.
ATTENTION:
This product is produced for home use and this warranty only covers failures
due to defects in material or workmanship which occurs during normal use. It
does not cover damage which occurs in shipment, or failures which are caused
by repairs, alterations or product not supplied by FUNAI CORP., or damage
which results from accident, misuse, abuse, mishandling, misapplication, alter-
ation, faulty installation, improper maintenance, commercial use such as hotel,
rental or office use of this product or damage which results from fire, flood, light-
ning or other acts of God.
FUNAI CORP. RESERVES THE RIGHT TO MODIFY ANY DESIGN OF
THIS PRODUCT WITHOUT PRIOR NOTICE.
To locate your nearest Funai Authorized Service Center or for general
service procedure, please call or write to the following:
FUNAI CORPORATION, INC.
SERVICE CENTER
19900 Van Ness Avenue, Torrance, CA 90501
Tel :1-800-605-8610
Head Office: 100 North Street, Teterboro, NJ 07608
THIS WARRANTY DOES NOT COVER PACKING MATERIALS, ANY
ACCESSORIES (EXCEPT REMOTE CONTROL), ANY COSMETIC
PARTS, COMPLETE ASSEMBLY PARTS, DEMO OR FLOOR MODELS.
PLEASE DO NOT SHIP YOUR UNIT TO THE TETERBORO ADDRESS.
EN
–
–
24
Español
Conexiones
Activación de la unidad
Ajuste del reloj
1
5
4
por primera vez
VCR
Consulte la “Basic TV Connection”
en la página delantera antes de
utilizar esta unidad.
VCR
VCR
- M E N U -
1
VCR
MENU
PROGRAMAR
AUTOREPETIR [OFF]
AJUSTE CANAL
B AJUSTE DE RELOJ
SELEC. IDIOMA
Canal de salida RF
Si el canal 3 se está utilizando para
una transmisión.
1)Programe su televisor al canal 4.
2)Inserte una cinta pregrabada en esta
unidad.
3)Pulse [SOURCE] en la unidad para
que se encienda la luz VCR OUT-
PUT.
1
Encienda el televisor y sin-
tonice al canal 3.
•
Si el canal 3 se está utilizando para una trans-
misión, vea la sección “RF Output Channel”.
•
Si no se ha ajustado el reloj,
aparece la pantalla AJUSTE
DE RELOJ cuando pulse
[MENU]. En este caso, vaya
al paso 2).
o
• Si aparece ruido en la pantalla de
TV, presione [VCR/TV] en el mando
a distancia.
4)Pulse una vez [PLAY B].
5)Después de unos segundos, pulse
[PLAY B] en el la unidad durante 3
segundos.
• El canal de salida RF cambiará del
canal 3 al canal 4 y podrá ver una
imagen reproducida.
• Cuando no aparezca una imagen en
la pantalla del televisor, repita el
paso 4).
2
3
STANDBY-ON
Control Remoto
Pantalla del televisor
SELEC. IDIOMA
ENGLISH
2
3
4
5
AJUSTE DE RELOJ
MES
1 0
DIA
– –
AÑO
– – – –
/
FRANCAIS
o
o
o
B ESPAÑOL
[ON]
HORA MINUTO AM/PM
– – – – – –
o
:
Seleccione el mes actual.
AJUSTE DE RELOJ
MES
1 0
DIA
0 3
AÑO
– – – –
CA 01
6)Pulse [STOP C] para parar la repro-
ducción.
/
HORA MINUTO AM/PM
– – – – – –
:
AJUSTE AUTO
Instalación de las pilas
Seleccione el día actual.
2
del control remoto
3
2
1
Conecta el cable de la caja de canales de cable o la
caja de satélite en la toma ANT-IN de la unidad?
AJUSTE DE RELOJ
MES
1 0
DIA
0 3
AÑO
2 0 0 5
SI
/
HORA MINUTO AM/PM
– – – – – –
Si
Pulse MENU
para salir.
:
Seleccione el año actual.
Conmutación VCR/DVD
NO
3
No Espere unos minutos.
Después del escaneo
STANDBY-ON
OPEN/
CLOSE
OPEN/CLOSE
/EJECT
N
y
STANDBY-ON
SPEED
AUDIO
POWER-ON
REC
TIMER
VCR
DVD
P.SCAN
PLAY
VIDEO
AUDIO
R
Q
PN
O
U
P
O
T
AJUSTE DE RELOJ
Y
X
REW
F
.FWD STOP/EJECT PLAY
RECORD
IR
CHANNEL
SOURCE
PREV
STOP
PLAY
NEXT
1
4
7
2
5
8
3
6
9
SKIP/CH.
MES
1 0
DIA
AÑO
VCR/TV
SLOW
• El sintonizador se detiene en el canal
/
0 3 LUN 2 0 0 5
memorizado más bajo.
0
VCR
+
DVD
1 0
o
Botón VCR
Botón DVD
DISPLAY
PAUSE
HORA MINUTO AM/PM
0 5 – – – –
• Puede seleccionar sólo los canales memo-
rizados en esta unidad con
[SKIP/CH. G/K H/L]
:
PLAY
STOP
Luz
RECORD
MENU
Seleccione la hora actual.
VCR OUTPUT
ENTER
(o [CHANNEL K/L]).
VCR
DVD
SETUP TOP MENU
RETURN
Luz
• Si aparece nuevamente "AJUSTE AUTO"
en la pantalla de TV, verifique las conex-
iones de cable. Presione nuevamente [B].
SEARCH
MODE
CLEAR/
MODE
ZOOM
C. RESET
DVD OUTPUT
SUBTITLE
T
-SET
ANGLE
REPEAT
A-B
SOURCE
6
Botón SOURCE
AJUSTE DE RELOJ
MES
1 0
DIA
AÑO
/
0 3 LUN 2 0 0 5
o
HORA MINUTO AM/PM
0 5 4 0 – –
:
MODO VCR
Seleccione los minutos actuales.
AJUSTE DE RELOJ
Pulse [VCR] en el control remoto.
(Compruebe que está encendida la luz
VCR OUTPUT.)
7
8
MODO DVD
Pulse [DVD] en el control remoto.
(Compruebe que está encendida la luz
DVD OUTPUT.)
MES
1 0
DIA
AÑO
/
0 3 LUN 2 0 0 5
o
HORA MINUTO AM/PM
0 5
:
4 0
P M AM
B PM
Seleccione "AM" o "PM".
Consejo
• Si pulsa sólo [SOURCE] en el panel
frontal NO cambía el modo del control
remoto. DEBE seleccionar también el
modo correcto en el control remoto.
Para salir de la pantalla AJUSTE DE
RELOJ
ES
–
–
25
Español
Reproducción de la grabadora de vídeo
Reproducción de DVD/CD
6
7
Antes: Encienda el televisor y cambie al canal 3.
Antes: Encienda el televisor, amplificador y otros equipos que puedan estar
conectados a esta unidad. Asegúrese que el televisor y el sintoamplificador de
audio (de venta en los comercios) están en el canal correcto.
• Si el canal 3 se está utilizando para una transmisión, vea la
sección "Canal de salida RF".
DVD
VCR
VCR
DVD-V
CD
4
OPEN/CLOSE
/EJECT
OPEN/CLOSE
/EJECT
STANDBY-ON
STANDBY-ON
SPEED
AUDIO
SPEED
AUDIO
Para empezar
1
3
2
4
1
2
1
1
la reproducción
1
4
7
2
5
8
3
6
9
OPEN/CLOSE
/EJECT
1
4
7
2
5
8
3
6
9
STANDBY-ON
SKIP/CH.
PLAY
SKIP/CH.
VCR/TV
SLOW
VCR/TV
SLOW
0
VCR
+1 0
DVD
Ponga un disco con la
etiqueta hacia arriba.
0
VCR
+1 0
DVD
DISPLAY
PAUSE
DISPLAY
PAUSE
Para parar la
reproducción
Para expulsar
OPEN/CLOSE
/EJECT
PLAY
STOP
Para empezar
la reproducción
Para parar la
PLAY
3
4
STOP
reproducción
STOP
3
RECORD
RECORD
STOP
PLAY
2
3
4
Control remoto
8
Modo DVD
Modo de grabadora de vídeo
Disco/cinta
(BOordteónnalfabético)
1
4
7
2
5
8
0
3
•Para seleccionar el canal.
•El botón +10 no tiene efecto
en el modo de grabadora de
vídeo.
6
•
Para seleccionar directamente
el capítulo o el título.
•
Para seleccionar directamente
la canción.
9
+1 0
•
•
Para buscar en avance/retroceso
en un disco.
Para empezar la reproducción en avance/
retroceso lento durante el modo de pausa.
•Para buscar en avance/
retroceso en un disco.
•Para el avance/retroceso
de una cinta.
•
•
•
Para seleccionar un ítem
en el menú de la grabadora
de vídeo.
ENTER
Para avanzar al siguiente
menú de la grabadora de
vídeo.
•Para mover el cursor y
determinar su posición.
•Para mover el curso y
determinar su posición.
OPEN/CLOSE
STANDBY-ON
/EJECT
SPEED
AUDIO
Para volver un paso
durante el ajuste del reloj y
temporizador.
A-B
•Para repetir entre los puntos •Para repetir entre los puntos
A y B elegidos.
1
4
7
2
5
8
3
6
9
A y B elegidos
ANGLE
AUDIO
SKIP/CH.
•Para seleccionar los ángulos
de la cámara en un disco.
VCR/TV
SLOW
•Para seleccionar el idioma de •Para seleccionar ESTÉREO,
audio en un disco. L-ch o R-ch.
•Para borrar los marcadores.
•Para borrar los marcadores. •Para retirar el Nº de estado
CLEAR/
C. RESET
•Para salir del menú de la
grabadora de vídeo.
•Para reponer el contador de
cinta.
0
+1 0
en la entrada de programa.
•Para borrar los números
•Para borrar los números
entrados incorrectamente.
DISPLAY
VCR
DVD
PAUSE
entrados incorrectamente.
•Para borrar el punt para la
•Para borrar el punt para la
repetición A-B.
repetición A-B.
•Para indicar el modo de
DISPLAY
DVD
•Para indicar el modo de
disco actual.
•Para indicar la hora actual,
contador de cinta y canal.
PLAY
disco actual.
• Para seleccionar el modo de
• Para seleccionar el modo
de salida de DVD.
STOP
salida de DVD
Para activar el mando a
distancia en el modo DVD
• Para activar el mando a
distancia en el modo DVD.
•Para llamar el menu en un
•
RECORD
MENU
MENU
MODE
•Para llamar el menú de la
grabadora de vídeo.
disco.
ENTER
•Para disponer el orden de
reproducción o la
reproducción aleatoria.
•Para activar/desactivar el
envolvente virtual.
•Para activar/desactivar el
nivel del negro.
•Para activar/desactivar el
envolvente virtual.
SETUP TOP MENU
RETURN
SEARCH
MODE
CLEAR/
C. RESET
MODE
ZOOM
OPEN/CLOSE
/EJECT
•Para abrir o cerrar la bandeja •Para abrir o cerrar la bandeja •Para expulsar el videocasete
de la grabadora de vídeo.
del disco.
del disco.
SUBTITLE
T-SET
ANGLE
REPEAT
A-B
•
•
Para hacer una pausa de la
reproducción o grabación de la cinta.
Para avanzar la reproducción
un cuadro a la vez.
•Para hacer una pausa de
reproducción del disco.
•Para avanzar la reproducción
un cuadro a la vez.
PAUSE
• Para hacer una pausa en la
reproducción del disco.
•
Para empezar la reproducción
del disco.
•
Para empezar la reproducción
del disco.
•
Para empezar la reproducción
de la cinta.
PLAY
RECORD
• Para empezar una grabaciòn
o una grabaciòn de un toque.
REPEAT
RETURN
•
Para reproducir repetidamente
un capítulo o título.
•
Para reproducir repetidamente
una canción o disco.
•Para volver a la operación
previa en el menú.
•Para volver a la operación
previa en el menú.
•Para buscar una canción.
•Para buscar la hora.
•Para colocar o buscar los
marcadores.
•
•
Para buscar un capítulo, título u hora.
Para colocar o buscar los
marcadores.
SEARCH
MODE
•Para llamar el menú de
búsqueda de índice u hora.
SETUP
•Para llamar el menú de
programación de DVD.
•Para llamar el menú de
programación de DVD.
SKIP/CH.
SKIP/CH.
•
Para cambiar de canal.
Para ajustar manualmente el
seguimiento durante la reproducción.
•
• Para saltar capítulos
• Para saltar canciones.
SLOW
• Para ver la cinta en cámara
lenta.
SPEED
•Para seleccionar la velocidad
de grabación.
STANDBY-ON
•Para encender o apagar la
unidad.
•Para encender o apagar la
unidad.
•Para encender o apagar la
unidad.
STOP
• Para parar la reproducción o
grabación.
• Para parar la reproducción. • Para parar la reproducción.
SUBTITLE
T-SET
•
Para poner la grabadora de
vídeo en el modo de espera
para una grabación con temporizador.
•Para seleccionar subtítulos
en un disco.
TOP MENU
VCR
•Para llamar el menú superior
en un disco.
•
•
Para seleccionar el modo de
salida de la grabadora de vídeo.
Para activar el mando a distancia
en el modo de la grabadora de vídeo.
VCR/TV
ZOOM
•
Para seleccionar la posición
de DVD o posición del televisor.
•
Para seleccionar la posición de
CD o la posición del televisor.
•
Para seleccionar la posición de la
grabadora de vídeo o posición del televisor.
•Para ampliar parte de la
imagen. (x2/x4)
ES
–
–
26
Quick Use Guide
Connections
Turn on the unit for the
Clock Set Up
1
5
4
first time
VCR
Please refer to “Basic TV
Connection” on the front page
before you use this unit.
VCR
VCR
- M E N U -
1
VCR
MENU
TIMER PROGRAMMING
AUTO REPEAT [OFF]
CHANNEL SET UP
B CLOCK SET
LANGUAGE SELECT
RF Output Channel
If channel 3 is already occupied for
broadcasting,
1)Set your TV to channel 4.
2)Insert a pre-recorded tape into this
unit.
3)Hit [SOURCE] on the unit so that the
VCR OUTPUT light is lit.
1
Turn on the TV and set it
to channel 3.
• If channel 3 is already occupied for broadcasting,
see“RF Output Channel” section.
• If the clock is not set, the
CLOCK SET screen
appears when you hit
[MENU]. In this case, go
to step 2).
or
• If noise appears on the TV screen,
hit [VCR/TV] on the remote control.
2
STANDBY-ON
Remote Control TV Screen
LANGUAGE SELECT
4)Hit [PLAY
B
]
once.
5)After a few seconds, hit [PLAY
B]
2
3
4
5
on the unit for 3 seconds.
CLOCK SET
B ENGLISH
FRANCAIS
ESPAÑOL
[ON]
• The RF output channel will change
to channel 4 from channel 3 and you
will see a playback picture.
• When a picture does not appear on
the TV screen, repeat step 4).
MONTH DAY
1 0 – –
YEAR
– – – –
/
or
or
or
HOUR MINUTE AM/PM
– – – – – –
or
:
Select the current month.
6)Hit [STOP
C]
to stop playback.
CLOCK SET
MONTH DAY
1 0 0 3
YEAR
– – – –
3
CH 01
/
HOUR MINUTE AM/PM
– – – – – –
:
Installing the Batteries
for the Remote Control
AUTO SET UP
2
Select the current day.
3
2
1
Do you connect the cable from the cable box or
the satellite box to the unit’s ANT-IN jack?
YES
CLOCK SET
MONTH DAY
1 0 0 3
YEAR
/
2 0 0 5
HOUR MINUTE AM/PM
– – – – – –
Yes Hit MENU to
:
VCR/DVD Switching
3
exit.
Select the current year.
NO
STANDBY-ON
OPEN/
N
OPEN/CLOSE
/EJECT
y
CLOSE
STANDBY-ON
SPEED
AUDIO
POWER-ON
REC
TIMER
VCR
DVD
P.SCAN
PLAY
No Please wait for a few minutes.
After scanning...
• The tuner stops on the lowest memorized
channel.
VIDEO
AUDIO
R
Q
PN
O
U
P
O
T
Y
X
REW
F
.FWD STOP/EJECT PLAY
RECORD
IR
CHANNEL
SOURCE
PREV
STOP
PLAY
NEXT
1
4
7
2
5
8
3
6
9
SKIP/CH.
CLOCK SET
VCR/TV
SLOW
MONTH DAY
YEAR
0
+1 0
VCR button
DVD button
DISPLAY
VCR
DVD
PAUSE
1 0 0 3 MON 2 0 0 5
/
or
PLAY
STOP
HOUR MINUTE AM/PM
0 5 – – – –
•
You can select only the channels memorized
VCR OUTPUT
light
RECORD
MENU
:
in this unit by using
ENTER
VCR
DVD
[SKIP/CH. G/K H/L]
(or [CHANNEL K/L]).
SETUP TOP MENU
RETURN
Select the current hour.
DVD OUTPUT
light
SEARCH
MODE
CLEAR/
C. RESET
MODE
ZOOM
SUBTITLE
T
-SET
ANGLE
REPEAT
A-B
• If “AUTO SET UP” appears on the TV
screen again, check the cable connections.
Then, hit [B] once again.
SOURCE
SOURCE button
6
CLOCK SET
MONTH DAY
YEAR
1 0 0 3 MON 2 0 0 5
/
or
VCR MODE
HOUR MINUTE AM/PM
0 5 4 0 – –
:
Hit [VCR] on the remote control.
Select the current minute.
CLOCK SET
(Verify that the VCR OUTPUT light is lit.)
DVD MODE
Hit [DVD] on the remote control.
(Verify that the DVD OUTPUT light is lit.)
7
8
MONTH DAY
YEAR
1 0 0 3 MON 2 0 0 5
/
or
HOUR MINUTE AM/PM
0 5
:
4 0
P M AM
B PM
Hint
Select “AM” or “PM”.
• Hitting only [SOURCE] on the front panel
DOES NOT switch the mode of the
remote control. You MUST select the cor-
rect mode on the remote control.
To exit the CLOCK SET
screen
EN
–
–
27
Quick Use Guide
VCR Playback
DVD/CD Playback
6
7
Before: Turn on the TV and set it to channel 3.
Before: Turn on the TV, amplifier and any other components which are con-
nected to this unit. Make sure the TV and audio receiver (commercially avail-
able) are set to the correct channel.
• If channel 3 is already occupied for broadcasting, see “RF
Output Channel” section.
DVD
VCR
VCR
DVD-V
CD
4
OPEN/CLOSE
/EJECT
OPEN/CLOSE
/EJECT
STANDBY-ON
STANDBY-ON
SPEED
AUDIO
SPEED
AUDIO
To start
playback
1
3
2
4
1
2
1
1
OPEN/CLOSE
/EJECT
1
4
7
2
5
8
3
6
9
STANDBY-ON
1
4
7
2
5
8
3
6
9
SKIP/CH.
SKIP/CH.
PLAY
VCR/TV
SLOW
VCR/TV
SLOW
Insert a disc with
label facing up.
0
VCR
+1 0
DVD
0
VCR
+1 0
DVD
DISPLAY
PAUSE
DISPLAY
PAUSE
To stop
playback
STOP
To eject
OPEN/CLOSE
/EJECT
To start
playback
3
4
To stop
PLAY
PLAY
STOP
playback
STOP
3
RECORD
RECORD
STOP
PLAY
2
3
4
Remote Control
8
VCR mode
DVD mode
Disc/Tape
(BAulpthtaobnetical order)
1
4
7
2
5
8
0
3
•To select channel.
•The +10 button has no effect
in VCR mode.
6
•
To select chapter or title directly. •To select track directly.
9
+1 0
•To search forward/backward
through a disc.
To begin slow forward/reverse
playback during the pause mode.
•To search forward/backward
through a disc.
•To forward/backward a tape.
•
• To select an item
on the VCR Menu.
• To advance to the next
ENTER
•To move the cursor and
determine its position.
•To move the cursor and
determine its position.
VCR Menu.
To go back one step during
•
OPEN/CLOSE
/EJECT
clock and timer setting.
STANDBY-ON
SPEED
AUDIO
A-B
•To repeat between your
chosen point A and B.
•To repeat between your
chosen point A and B.
ANGLE
AUDIO
•To select camera angles on
a disc.
1
4
7
2
5
8
3
6
9
SKIP/CH.
•To select audio languages on •To select STEREO,
L-ch or R-ch.
a disc.
VCR/TV
SLOW
•To clear the markers.
•
•To clear the markers.
•To clear the numbers.
entered incorrectly.
CLEAR/
C. RESET
To remove status number in
program input.
•To exit the VCR Menu.
•To reset the tape counter.
•
•
To clear the numbers entered incorrectly.
To cancel the point for A-B repeat.
0
VCR
+1 0
DVD
•
To cancel the point for A-B repeat.
DISPLAY
PAUSE
DISPLAY
DVD
•To display the current disc
•To display the current disc
mode.
•To display the current time,
tape counter, and channel.
mode.
• To select the DVD output
mode.
• To select the DVD output
mode.
PLAY
• To activate the remote control • To activate the remote control
in DVD mode.
in DVD mode.
STOP
MENU
MODE
•To call up the Menu
on a disc.
•To call up the VCR Menu.
RECORD
MENU
•To arrange the playing
order or play randomly.
•To set virtual surround on/off.
•To set black level on/off.
•To set virtual surround on/off.
ENTER
OPEN/CLOSE
/EJECT
SETUP TOP MENU
RETURN
•To open or close the disc
tray.
•To open or close the disc
tray.
•To eject the video cassette
from the VCR.
SEARCH
MODE
CLEAR/
C. RESET
MODE
ZOOM
• To pause tape playback or
recording.
•To advance playback
one frame at a time.
PAUSE
•To pause disc playback.
•To advance playback
one frame at a time.
• To pause disc playback.
SUBTITLE
T-SET
ANGLE
REPEAT
A-B
• To begin tape playback.
• To begin disc playback.
• To begin disc playback.
PLAY
RECORD
• To start a recording or
One Touch Recording.
REPEAT
RETURN
•To play a chapter or title
repeatedly.
•To play a track or disc
repeatedly.
•To return to the previous
operation in menu.
•To return to the previous
operation in menu.
SEARCH
MODE
•To search track.
•To search time.
•To set or search the markers.
•To search chapter, title or time.
•To set or search the markers.
•To call up the index or time
search menu.
SETUP
•To call up the DVD setup
menu.
•To call up the DVD setup
menu.
SKIP/CH.
SKIP/CH.
• To change channels.
•
To adjust the tracking manually
during playback.
• To skip chapters.
• To skip tracks.
SLOW
• To view the tape
in slow motion.
SPEED
•To select the recording speed.
•To turn the unit on or off.
STANDBY-ON
•To turn the unit on or off.
• To stop playback.
•To turn the unit on or off.
STOP
• To stop playback.
• To stop playback or recording.
SUBTITLE
T-SET
•To put the VCR into standby
mode for a Timer Recording.
•To select subtitles on a disc.
TOP MENU
VCR
•To call up the Top Menu
on a disc.
• To select the VCR output
mode.
• To activate the remote control
in VCR mode.
VCR/TV
ZOOM
• To select DVD position or
TV position.
• To select CD position or TV
position.
• To select VCR position or
TV position.
•To magnify part of a picture.
(x2/x4)
1VMN20455 / H9870UD #####
Printed in China
|