EN9110
PRECAUTIONS
! Do not use the monitor near water, e.g. near a bathtub, washbowl, kitchen
sink, laundry tub, swimming pool or in a wet basement.
! Do not place the monitor on an unstable cart, stand, or table. If the
monitor falls, it can injure a person and cause serious damage to the
appliance. Use only a cart or stand recommended by the manufacturer or
sold with the monitor. If you mount the monitor on a wall or shelf, use a
mounting kit approved by the manufacturer and follow the kit instructions.
! Slots and openings in the back and bottom of the cabinet are provided for
ventilation. To ensure reliable operation of the monitor and to protect it
from overheating, be sure these openings are not blocked or covered. Do
not place the monitor on a bed, sofa, rug, or similar surface. Do not place
the monitor near or over a radiator or heat register. Do not place the
monitor in a bookcase or cabinet unless proper ventilation is provided.
! The monitor should be operated only from the type of power source
indicated on the label. If you are not sure of the type of power supplied to
your home, consult your dealer or local power company.
! The monitor is equipped with a three-pronged grounded plug, a plug with
a third (grounding) pin. This plug will fit only into a grounded power outlet
as a safety feature. If your outlet does not accommodate the three-wire
plug, have an electrician install the correct outlet, or use an adapter to
ground the appliance safely. Do not defeat the safety purpose of the
grounded plug.
! Unplug the unit during a lightening storm or when it will not be used for
long period of time. This will protect the monitor from damage due to
power surges.
! Do not overload power strips and extension cords. Overloading can result
in fire or electric shock.
! Never push any object into the slot on the monitor cabinet. It could short
circuit parts causing a fire or electric shock. Never spill liquids on the
monitor.
! Do not attempt to service the monitor by yourself; opening or removing
covers can expose you to dangerous voltages and other hazards. Please
refer all servicing to qualified service personnel.
! To ensure satisfactory operation, use the monitor only with UL listed
computers which have appropriate configured receptacles marked
between 100 - 240V AC, Min. 5A.
! The wall socket shall be installed near the equipment and shall be easily
accessible.
! For use only with power adaptor manufacturer by CHI SAM
ELECTRONIC , model CH-1205
•
Do not install the monitor in a location near heat sources such as
radiators or air ducts, or in a place subject to direct sunlight, or excessive
dust or mechanical vibration or shock.
•
Save the original shipping carton and packing materials, as they will come
in handy if you ever have to ship your monitor.
2
EN9110
PRECAUTIONS (cont)
•
•
For maximum protection, repackage your monitor as it was originally
packed at the factory.
To keep the monitor looking new, periodically clean it with a soft cloth.
Stubborn stains may be removed with a cloth lightly dampened with a mild
detergent solution. Never use strong solvents such as thinner, benzene,
or abrasive cleaners, since these will damage the cabinet. As a safety
precaution, always unplug the monitor before cleaning it.
3
EN9110
SPECIAL NOTES ON LCD MONITORS
The following symptoms are normal with LCD monitor and do not indicate a
problem.
NOTES
•
Due to the nature of the fluorescent light, the screen may flicker during
initial use. Turn off the Power Switch and then turn it on again to make
sure the flicker disappears.
•
•
You may find slightly uneven brightness on the screen depending on the
desktop pattern you use.
The LCD screen has effective pixels of 99.99% or more. It may include
blemishes of 0.01% or less such as a missing pixel or a pixel lit all of the
time.
•
Due to the nature of the LCD screen, an afterimage of the previous screen
may remain after switching the image, when the same image is displayed
for hours. In this case, the screen is recovered slowly by changing the
image or turning off the Power Switch for hours.
BEFORE YOU OPERATE THE MONITOR
FEATURES
FEATURES
•
•
•
•
•
•
48cm(19”) TFT Color LCD Monitor
Crisp, Clear Display for Windows
Recommened Resolutions: 1280 X 1024 @60Hz
EPA ENERGY
Dual Input (DVI + Analog)
STAR®
Space Saving, Compact Case Design
CHECKING THE CONTENTS OF THE PACKAGE
The product package should include the following items:
1. LCD Monitor
2. 15-pin D-Sub Cable
3. DVI Cable
4. Power Cord
5. External Power Adapter
6. Driver Disk
7. Quick Start Guide (QSG)
8. Warranty, Notices, Warnings & Precautions Booklet
9. Input Not Supported Solution Sheet
4
EN9110
INSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS
SWIVEL BASE
Install
Remove
Figure 1 Installing and Removing the Swivel Base
POWERCORD
Power Source:
1. Make sure that the power cord is the correct type required in your area.
2. This LCD monitor has an External universal power supply that allows
operation in either 100/120V AC or 220/240V AC voltage area (No user
adjustment is required.)
3. Connect the AC-power cord into your LCD monitor’s External Adapter
input socket, and then plug the other end of External adapter to LCD
monitor’s DC-power-input. The AC-power cord may be connected to either
a wall power outlet or the power outlet socket on your PC, depending on
the type of power cord supplied with your LCD monitor.
NOTES
A certified power supply cord has to be used with this equipment. The
relevant national installation and/or equipment regulations shall be
considered. A certified power supply cord not lighter than ordinary polyvinyl
chloride flexible cord according to IEC 60227 (designation H05VV-F 3G
0.75mm
cord be of synthetic rubber according to IEC 60245 (designation H05RR-F 3G
0.75mm ) shall be used.
!
or H05VVH2-F2 3G 0.75mm! ) shall be used. Alternative a flexible
!
5
EN9110
INSTALLATIONS INSTRUCTIONS (cont)
PREPARING TO INSTALL THE CABLES
1. Remove the wall mounting hole cover.
2. Remove the cable cover.
6
EN9110
INSTALLATIONS INSTRUCTIONS (cont)
CABLE CONNECTIONS
1 – Connect the DC-jack power cable into DC-IN connector on the back of the
monitor.
2. Connect one end of the 15-pin D-Sub cable to the back of the monitor and
connect the other end to the computer’s D-Sub port.
3. (Optional – Requires a video card with DVI port) Connect one end of the
24-pin DVI cable to the back of the monitor and connect the other end to the
computer’s DVI port. be tightened.
4 – Connect the female end of the power cord to the monitor’s power adapter
and connect the male end of the power cord to the AC outlet.
Caution: If the AC outlet is not grounded (with three holes), install the proper
grounding adapter (not supplied).
Figure 2 Connecting Cables
1. External Adapter
2. 15-pin D-Sub Cable
3. DVI Cable
4. Power Cord
7
EN9110
INSTALLATION INSTRUCTIONS (cont)
Preparing To Install The Optional Wall Mount Arm (Not Included)
CONNECTIONS
This monitor can be attached to a wall mounting arm you can purchase
separately from Ergotron (www.ergotron.com). Turn the power OFF then dis-
connect the cables from the monitor before performing the procedure below.
Lay the monitor face down on a soft surface.
1. Remove wall mounting hole cover.
2. Remove the cable cover.
3. Remove the 4 screws holding the base to the back of the monitor.
4. Remove the base.
8
EN9110
INSTALLATION INSTRUCTIONS (cont)
Attaching The Optional Wall Mount Arm (not supplied)
Follow these steps to finish installing the wall mounting arm:
1. Place the wall mounting arm onto the back of the monitor. Line up
the holes of the arm with the holes in the back of the monitor.
2. Insert the 4 screws into the holes and tighten.
3. Reconnect the cables. Refer to the user’s manual that came with
the optional wall mounting arm for instrucstions on attaching it to the
wall.
9
EN9110
ADJUSTING THE VIEWING ANGLE
INSTALLATION INSTRUCTIONS
•
•
•
For optimal viewing it is recommended to look at the full face of the
monitor, then adjust the monitor’s angle to your own preference.
Hold the stand so you do not topple the monitor when you change the
monitor’s angle.
You are able to adjust the monitor’s angle from -5° to 20°.
Figure 3
NOTES
•
•
Do not touch the LCD screen when you change the angle. It may cause
damage or break the LCD screen.
Careful attention is required not to catch your fingers or hands when you
change the angle.
10
EN9110
OPERATING INSTRUCTIONS
GENERAL INSTRUCTIONS
Press the power button to turn the monitor on or off. The other control buttons
are located on the side of the monitor (See Figure 4). By changing these
settings, the picture can be adjusted to your personal preferences.
•
•
•
The power cord should be connected.
Connect the video cable from the monitor to the video card.
Press the power button to turn on the monitor. The power indicator will
light up.
Figure 4
External Control Button
EXTERNAL CONTROLS
1. Auto Config / Exit
5. Power Indicator
6. Power Button
2.
3.
/ Brightness
/ Contrast
4. MENU / ENTER
11
EN9110
FRONT PANEL CONTROL
•
•
Power Button:
Press this button to switch the monitor’s power ON or OFF.
MENU / ENTER :
Activate OSD menu when OSD is OFF or activate/de-activate adjustment
function when OSD is ON or Exit OSD menu when in Brightness/Contrast
OSD status.
•
•
Brightness
Adjust brightness or function adjust.
/
:
Contrast
Adjust contrast or function adjust.
/
:
• Auto Adjust button / Exit:
1. When OSD menu is in active status, this button will act as EXIT-KEY
(EXIT OSD menu)
2. When OSD menu is in OFF, press this button for 2 seconds to
activate the Auto Adjustment function.
The Auto Adjustment function is used to set the HPos, VPos, Clock
and Focus.
• Power Indicator:
Green
Orange —
—
Power On mode.
Off mode.
12
EN9110
HOW TO ADJUST A SETTING
1. Press the MENU-button to activate the OSD window. See figure 5.
2. Press or to select the desired function. See figure 5.
3. Press the MENU-button again to activate the highlighted function.
4. Press
or
to adjust the selected function.
Note:
is used to adjust the function down &
is used to adjust the
function up. This is due to the orientation of the adjustment level bar.
5. When the OSD window is active, it shows the input signal timing. The "H"
stands for the horizontal frequency and "V" for the vertical frequency.
6. To exit and save, select the exit function, or leave the monitor alone for 10
seconds. If you want to adjust another function press MENU again and
repeat steps 2-4.
Figure 5 The OSD Message
13
EN9110
ADJUSTING THE PICTURE
Below describes the function of each OSD icon.
Contrast
Adjust the picture contrast.
1.
Brightness
Input Selected
Focus
Adjust the picture brightness.
2.
3.
4.
5.
Input Signal source selected ( select Analog
or Digital input source )
Adjust picture Focus (available in Analog
mode only).
Adjust picture Clock (available in Analog
mode only).
Clock
Adjust the horizontal position of the picture
(availab in Analog mode only).
6.
7.
8.
H- Position
Adjust the vertical position of the picture
(available in Analog mode only).
V- Position
Language
Multi-Language selection
Stretch the picture to fit full screen, screen
size ratio or native size (this function only
works when the resolution setting is lower
than the native resolution of 1280x1024).
9.
Scaling Mode
Red
10.
11.
Adjusts Red intensity.
Green
Adjusts Green intensity.
Adjusts Blue intensity.
Blue
12.
13.
The color temperature for 6500°K is
x=0.313, y=0.329.
(6500K)Color
C1
C2
The color temperature for 7800°K is
x=0.296, y=0.311.
Clear old settings of Auto-configuration, re-
activates auto-configuration and set the
color temperature to 7800°K.
(7800K)Color
Reset
14.
15.
16.
Exit
Save user adjustment and exit OSD menu.
14
EN9110
PLUG AND PLAY
Plug & Play DDC1/2B Feature
This monitor is equipped with VESA DDC1/2B capabilities according to the
VESA DDC STANDARD. It allows the monitor to inform the host system of its
identity and, depending on the level of DDC used, communicate additional
information about its display capabilities. The communication channel is
defined in two levels, DDC1 and DDC2B.
The DDC1 is a unidirectional data channel from the display to the host that
continuously transmits EDID information. The DDC2B is a bidirectional data
channel based on the I²C protocol. The host can request EDID information
over the DDC2B channel.
THIS MONITOR WILL APPEAR TO BE NON-FUNCTIONAL IF THERE IS
NO VIDEO INPUT SIGNAL. IN ORDER FOR THIS MONITOR TO OPERATE
PROPERLY, THERE MUST BE A VIDEO INPUT SIGNAL.
This monitor meets the Green monitor standards as set by the Video
Electronics Standards Association (VESA) and/or the United States
Environmental Protection Agency (EPA) and The Swedish Confederation
Employees (NUTEK). This feature is designed to conserve electrical energy
by reducing power consumption when there is no video-input signal present.
When there is no video input signal this monitor, following a time-out period,
will automatically switch to an OFF mode. This reduces the monitor's internal
power supply consumption. After the video input signal is restored, full power
is restored and the display is automatically redrawn. The appearance is
similar to a "Screen Saver" feature except the display is completely off. The
display is restored by pressing a key on the keyboard, or clicking the mouse.
USING THE RIGHT POWER CORD :
The accessory power cord for the Northern American region is the wallet plug
with NEMA 5-15 style and is UL listed and CSA labeled. The voltage rating for
the power cord shall be 125 volts AC.
Supplied with units intended for connection to power outlet of personal
computer: Please use a cord set consisting of a minimum No. 18 AWG, type
SJT or SVT three conductors flexible cord. One end terminates with a
grounding type attachment plug, rated 10A, 250V, CEE-22 male configuration.
The other end terminates with a molded-on type connector body, rated 10A,
250V, having standard CEE-22 female configuration.
Please note that power supply cord needs to use VDE 0602, 0625, 0821
approval power cord in European counties.
15
EN9110
TECHNICAL SUPPORT (FAQ)
Problem & Question
Power LED is not on
Possible Solution
*Check if the Power Switch is in the ON
position
*Power Cord should be connected
*Check if the PC system is Plug & Play
compatible
No Plug & Play
*Check if the Video Card is Plug & Play
compatible
*Check if the D-15 plug pin of Video
Cable is bent
*Make sure the Envision Monitor Drivers
are installed
(Envision Monitor Drivers are available
at: www.envisionmonitor.com)
*Adjust the Contrast and Brightness
Controls.
Picture is fuzzy
Picture bounces or a wave
pattern is present in the picture
The power LED is ON (orange)
but there’s no video or no
picture.
*Move electrical devices that may cause
electrical interference.
*Computer Power Switch should be in
the ON position.
*Computer Video Card should be snugly
seated in its slot
*Make sure monitor’s video cable is
properly connected to the computer.
*Inspect monitor’s video cable and make
sure none of the pins are bent.
*Make sure computer is operational by
hitting the CAPS LOCK key on the
keyboard while observing the CAPS
LOCK LED. The LED should either
turn ON or OFF after hitting the CAPS
LOCK key.
Missing one of the primary
colors (RED, GREEN, or
BLUE)
*Inspect the monitor’s video cable and
make sure that none of the pins are
bent.
16
EN9110
Screen image is not centered or sized *Adjust pixel frequency (CLOCK) and
properly.
Picture has color defects
(white does not look white)
FOCUS or press hot-key (AUTO)
*Adjust RGB color or select a pre-set
color temperature from OSD.
Horizontal or vertical disturbances on *Use win 95/98 shut-down mode
the screen
Adjust CLOCK and FOCUS or
perform hot- key (AUTO-key).
CLOCK (pixel frequency) controls the number of pixels scanned by one
horizontal sweep. If the frequency is not correct, the screen shows vertical
stripes and the picture has not correct width.
FOCUS adjusts the phase of the pixel clock signal. With a wrong phase
adjustment the picture has horizontal disturbances in light picture.
For FOCUS and CLOCK adjustment use “dot-pattern” or Win 95/98 shut-
down mode pattern .
17
EN9110
ERROR MESSAGE & POSSIBLE SOLUTION
NO SIGNAL
1. Check that the signal-cable is properly connected , If the connector is
loose, tighten the connector’s screws.
2. Check the signal-cable’s connection pins for damage.
INPUT NOT SUPPORT
Your computer has been set to unsuitable display mode ,set the computer to
display mode given in the following table.
UNSUPPORTED MODE TRY DIFFERENT VIDEO CARD SETTING
Your computer resolution is out of VESA-SPEC
RESOLUTION
VERTICAL
RESOLUTION
FREQUENCY
640 × 400
640 × 350
720 × 400
720 × 400
640 × 480
640 × 480
640 × 480
640 × 480
800 × 600
800 × 600
800 × 600
800 × 600
800 × 600
1024 × 768
1024 × 768
70Hz
70Hz
70Hz
85Hz
60Hz
72Hz
75Hz
85Hz
56Hz
60Hz
72Hz
75Hz
85Hz
60Hz
70Hz
18
EN9110
1024 × 768
1024 × 768
1280 × 1024
1280 × 1024
1280 × 1024
1152 × 864
1280 × 960
1280 × 960
640 × 480
75Hz
85Hz
60Hz
75Hz
85Hz
75Hz
60Hz
85Hz
67Hz
75Hz
56Hz
832 × 624
640 × 400
NOTE: For digital input, the resolution 1280 x 1024 @ 85Hz
and 1280 x 960 @ 85Hz are not supported
19
EN9110
HOW TO INSTALL THE DRIVER-DISK (INF & ICM FILE)
FOR FIRST TIME INSTALL :
This is a Plug & Play LCD monitor. Turn off the PC then connect the
cables. Power on the PC and it will automatically detect your new monitor.
The Windows Operating system will automatically install a plug & play
driver for it. If you would still like to install the driver included in the
diskette that came with the monitor, log-on to our website at
Driver” section.
20
EN9110
APPENDIX
SPECIFICATIONS
Driving system TFT Color LCD
LCD Panel
Input
Size
Pixel pitch
Viewable angle
Response time 25 ms ( Typical )
Video
48cm(19.0")
0.294mm( H )x 0.294mm( V )
170° (H) 170° (V)
R,G,B Analog Interface
Separate Sync. H/V TTL
H-Frequency
V-Frequency
31KHz – 92KHz
55-85Hz
Display Colors
Dot Clock
16.7M Colors
135MHz
Max. Resolution
Plug & Play
1280 x 1024 @85Hz
VESA DDC1/2BTM
<60W
ON Mode
EPA ENERGY
STAR®
OFF Mode
<5W
Input Connector
D-Sub 15pin
Input Video Signal
Analog:0.7Vp-p(standard),
75 OHM, Positive
DVI 24pin
Input Connector
Input Video Signal
Maximum Screen Size
Digital sigal
Horizontal : 376.32mm
Vertical : 301.056mm
12VDC/5.0A 60W Max
Operating Temp: 0° to 40°C
Storage Temp.: -10° to 50°C
Operating Humidity :
20% to 90%
Power Source
Environmental
Considerations
Weight
6.9Kgs Unit (net)
432.00
378.32
198.15
L901-a
140.00
250.00
21
EN9110
Switch
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Auto Adjust Key
/ Brightness
/ Contrast
Power Button
MENU/ Exit
Contrast
Brightness
Input Selected
Focus
External Controls:
Functions
Clock
H-Position
V-Position
Auto-center
Language
Scaling Mode
C1 ( 6500°K )
C2 ( 7800°K )
RGB Color temperature
Recall
Exit
Power Consumption
Regulatory
Compliance
( Maximum )
60 Watts
UL, CSA, FCC, TÜV, CE,
ISO13406-2, Windows XP Logo
22
EN9110
FACTORY PRESET TIMING TABLE
HORIZONTAL
VERTICAL
FREQUENCY
STANDARD
Dos-mode
Dos-mode
Dos-mode
VGA
RESOLUTION
FREQUENCY
640 × 400
720 x 400
31.47kHz
31.47kHz
31.47kHz
31.47kHz
35.00kHz
37.50kHz
37.86kHz
37.879kHz
46.875kHz
35.16kHz
48.01kHz
49.725kHz
48.363kHz
56.476kHz
60.021kHz
64.000kHz
80.000kHz
91.146kHz
79.976kHz
60.000kHz
80.000kHz
70.0Hz
70.0Hz
70.0Hz
60.0Hz
66.6Hz
75.0Hz
72.0Hz
60.0Hz
75.0Hz
56.0Hz
72.0Hz
75.0Hz
60.0Hz
70.0Hz
75.0Hz
60.0Hz
75.0Hz
85.0Hz
75.0Hz
60.0Hz
85.0Hz
720 x 400
640 × 480
640 × 480
640 × 480
640 × 480
800 × 600
800 × 600
800 × 600
800 × 600
832 × 624
1024 × 768
1024 × 768
1024 × 768
1280 × 1024
1280 × 1024
1280 × 1024
1152 × 864
1280 × 960
1280 × 960
SVGA
XGA
SXGA
Note: The factory preset mode for DOS is 720x400 @70Hz.
23
EN9110
CONNECTOR PIN ASSIGNMENT
1
6
5
10
15
11
15 - Pin Color Display Signal Cable
PIN NO.
DESCRIPTION
PI N NO.
DESCRIPTION
+5V
Detect Cable
NC
DDC-Serial Data
H-Sync
V-Sync
1.
2.
3.
4.
5.
6.
7.
8.
Red
Green
Blue
Ground
Ground
R-Ground
G-Ground
B-Ground
9.
10.
11.
12.
13.
14.
15.
DDC-Serial Clock
24 - Pin Color Display Signal Cable
PIN NO.
DESCRIPTION
PI N NO.
DESCRIPTION
1.
2.
3.
TMDS Data 2-
TMDS Data 2+
TMDS Data 2/4
Shield
13.
14.
15.
TMDS Data 3+
+5V Power
Ground(for+5V)
4.
5.
6.
7.
TMDS Data 4-
TMDS Data 4+
DDC Clock
16.
17.
18.
19.
Hot Plug Detect
TMDS Data 0-
TMDS Data 0+
TMDS Data 0/5
Shield
DDC Data
24
EN9110
8.
9.
10.
11.
N.C.
20.
21.
22.
23.
TMDS Data 5-
TMDS Data 1-
TMDS Data 1+
TMDS Data 1/3
Shield
TMDS Data 5+
TMDS Clock Shield
TMDS Clock +
12.
TMDS Data 3-
24.
TMDS Clock -
25
EN9110
WARRANTY STATEMENT
for Envision Color Monitors
Including those Sold within North America as Specified
Envision Peripherals, Inc. warrants this product to be free from defects in
material and workmanship for a period of three (3) years after the original
date of consumer purchase. During this period, EPI ( EPI is the abbreviation
of Envision Peripherals, Inc. ) will, at its option, either repair the defective
product with new or rebuilt parts, or replace it with a new or rebuilt product at
no charge except as *stated below. The parts or product that are replaced
become the property of EPI.
In the USA to obtain service under this limited warranty, call EPI for the name
of the Authorized Service Center in your area. Deliver the product freight
pre-paid, along with the dated proof of purchase, to the EPI Authorized
Service Center. If you cannot deliver the product in person:
! Pack it in its original shipping container (or equivalent)
! Put the RMA number on the address label
! Put the RMA number on the shipping carton
! Insure it (or assume the risk of loss / damage during shipment)
! Pay all shipping charges
EPI is not responsible for damage to inbound product that was not properly
packaged.
EPI will pay the return shipment charges within one of the countries specified
within this warranty statement. EPI is not responsible for any costs associated
with the transportation of product across international borders. This includes
the international borders of the countries within this warranty statements.
In the United States and Canada contact your Dealer or EPI Customer
Service, RMA Department at the toll free number (888) 838-6388. Or you can
* This limited warranty does not cover any losses or damages that occur as a
result of:
! Shipping or improper installation or maintenance
! Misuse
! Neglect
! Any cause other than ordinary commercial or industrial application
! Adjustment by non-authorized source
! Repair, modification, or installation of options or parts by anyone other
than an EPI Authorized Service Center
26
EN9110
! Improper environment
! Excessive or inadequate heating or air conditioning or electrical power
failures, surges, or other irregularities
This three-year limited warranty does not cover any of the product's firmware
or hardware that you or any third party have modified or altered; you bear the
sole responsibility and liability for any such modification or alteration.
ALL EXPRESS AND IMPLIED WARRANTIES FOR THIS PRODUCT
(INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS
FOR A PARTICULAR PURPOSE) ARE LIMITED IN DURATION TO A
PERIOD OF THREE (3) YEARS FOR PARTS AND LABOR FROM THE
ORIGINAL DATE OF CONSUMER PURCHASE. NO WARRANTIES (EITHER
EXPRESSED OR IMPLIED) APPLY AFTER THIS PERIOD. IN THE UNITED
STATES OF AMERICA, SOME STATES DO NOT ALLOW LIMITATIONS ON
HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE
LIMITATIONS MAY NOT APPLY TO YOU.
EPI OBLIGATIONS AND YOUR REMEDIES HEREUNDER ARE SOLELY
AND EXCLUSIVELY AS STATED HERE. EPI’ LIABILITY, WHETHER BASED
ON CONTRACT, TORT. WARRANTY, STRICT LIABILITY, OR OTHER
THEORY, SHALL NOT EXCEED THE PRICE OF THE INDIVIDUAL UNIT
WHOSE DEFECT OR DAMAGE IS THE BASIS OF THE CLAIM. IN NO
EVENT SHALL ENVISION PERIPHERALS, INC. BE LIABLE FOR ANY LOSS
OF PROFITS, LOSS OF USE OR FACILITIES OR EQUIPMENT OR OTHER
INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGE. IN THE UNITED
STATES OF AMERICA, SOME STATES DO NOT ALLOW THE EXCLUSION
OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES. SO
THE ABOVE LIMITATION MAY NOT APPLY TO YOU. ALTHOUGH THIS
LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS. YOU MAY
HAVE OTHER RIGHTS WHICH MAY VARY FROM STATE TO STATE.
In the United States of America, this limited warranty is only valid for Products
purchased in the Continental United States, Alaska, and Hawaii.
Outside the United States of America, this limited warranty is only valid for
Products purchased in Canada.
27
|