OWNER’S
MANUAL
EMERSON AND THE G-CLEF LOGO ARE REGISTERED
TRADEMARKS OF EMERSON RADIO CORP., PARSIPPANY,
NEW JERSEY, U.S.A.
DVD PLAYER with VIDEO CASSETTE RECORDER
EWD2203
ReWritable
Recordable
POWER
OPEN/CLOSE
CH-UP
STOP/EJECT
FF
OUTPUT
DVD
STOP
FWD
REW
REV
PLAY
VCR
REC
TIMER
REC
VIDEO
AUDIO
PLAY
CH-DOWN
PLAY
DISC IN
INSTRUCCIONES EN ESPAÑOL INCLUIDAS.
If you need additional assistance for set-up or operating
-
-
after reading owner’s manual, please call TOLL FREE : 1 800 256-2487
Please read before using this equipment.
IMPORTANT SAFEGUARDS
1. Read Instructions - All the safety and operating instructions
ing of the mast and supporting structure, grounding of the
lead-in wire to an antenna discharge unit, size of grounding
conductors, location of antenna-discharge unit, connection
to grounding electrodes, and requirements for the grounding
electrode. (Fig. A)
should be read before the appliance is operated.
2. Retain Instructions- The safety and operating instructions
should be retained for future reference.
3. Heed Warnings - All warnings on the appliance and in the
operating instructions should be adhered to.
4. Follow Instructions - All operating and use instructions
should be followed.
FIGURE A
ANTENNA
LEAD
EXAMPLE OF ANTENNA GROUNDING
WIRE
AS PER NATIONAL ELECTRICAL CODE
GROUND
CLAMP
5. Cleaning - Unplug this video product from the wall outlet
before cleaning. Do not use liquid cleaners or aerosol clean-
ANTENNA
DISCHARGE UNIT
(NEC SECTION 810-20)
ers.
Use
a
damp
cloth
for
cleaning.
EXCEPTION: A product that is meant for uninterrupted ser-
vice and, that for some specific reason, such as the possibil-
ity of the loss of an authorization code for a CATV convert-
er, is not intended to be unplugged by the user for cleaning
or any other purpose, may exclude the reference to unplug-
ging the appliance in the cleaning description otherwise
required in item 5.
6. Attachments - Do not use attachments not recommended by
the video product manufacturer as they may cause hazards.
7. Water and Moisture- Do not use this video product near
water, for example, near a bath tub, wash bowl, kitchen sink,
or laundry tub, in a wet basement, or near a swimming pool,
and the like.
ELECTRIC
SERVICE
EQUIPMENT
GROUNDING CONDUCTORS
(NEC SECTION 810-21)
GROUND CLAMP
NEC – NATIONAL ELECTRICAL CODE
POWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ART 250, PART H)
S2898A
14. Lightning - For added protection for this video product dur-
ing a lightning storm, or when it is left unattended and
unused for long periods of time, unplug it from the wall out-
let and disconnect the antenna or cable system. This will pre-
vent damage to the video product due to lightning and
power-line surges.
15. Power Lines - An outside antenna system should not be
located in the vicinity of overhead power lines or other elec-
tric light or power circuits, or where it can fall into such
power lines or circuits. When installing an outside antenna
system, extreme care should be taken to keep from touching
such power lines or circuits as contact with them might be
fatal.
8. Accessories - Do not place this video
product on an unstable cart, stand, tripod,
bracket, or table. The video product may
fall, causing serious injury to a child or
adult, and serious damage to the appli-
ance. Use only with a cart, stand, tripod,
bracket, or table recommended by the
16. Overloading - Do not overload wall outlets and extension
manufacturer, or sold with the video
cords as this can result in a risk of fire or electric shock.
product. Any mounting of the appliance should follow the
manufacturer's instructions and should use a mounting
accessory recommended by the manufacturer. An appliance
and cart combination should be moved with care. Quick
stops, excessive force, and uneven surfaces may cause the
appliance and cart combination to overturn.
17. Object and Liquid Entry - Never push objects of any kind
into this video product through any openings as they may
touch dangerous voltage points or short-out parts that could
result in a fire or electric shock. Never spill liquid of any
kind on the video product.
18. Servicing - Do not attempt to service this video product
yourself as opening or removing covers may expose you to
dangerous voltage or other hazards. Refer all servicing to
qualified service personnel.
19. Damage Requiring Service - Unplug this video product from
the wall outlet and refer servicing to qualified service per-
sonnel under the following conditions:
a. When the power-supply cord or plug is damaged.
b. If liquid has been spilled, or objects have fallen into the
9. Ventilation - Slots and openings in the cabinet are provided
for ventilation and to ensure reliable operation of the video
product and to protect it from overheating, and these open-
ings must not be blocked or covered. The openings should
never be blocked by placing the video product on a bed,
sofa, rug, or other similar surface. This video product should
not be placed in a built-in installation such as a bookcase or
rack unless proper ventilation is provided or the manufac-
turer's instructions have been adhered to.
10. Power Sources - This video product should be operated only
from the type of power source indicated on the marking
label. If you are not sure of the type of power supply to your
home, consult your appliance dealer or local power compa-
ny. For products intended to operate from battery power, or
other sources, refer to the operating instructions.
11. Grounding or Polarization - This video product is equipped
with a polarized alternating-current line plug (a plug having
one blade wider than the other). This plug will fit into the
power outlet only one way. This is a safety feature. If you are
unable to insert the plug fully into the outlet, try reversing
the plug. If the plug should still fail to fit, contact your elec-
trician to replace your obsolete outlet. Do not defeat the
safety purpose of the polarized plug.
12. Power Cord Protection - Power supply cords should be rout-
ed so that they are not likely to be walked on or pinched by
items placed upon or against them, paying particular atten-
tion to cords at plugs, convenience receptacles, and the point
where they exit from the appliance.
video product.
c. If the video product has been exposed to rain or water.
d. If the video product does not operate normally by following
the operating instructions. Adjust only those controls that
are covered by the operating instructions as an improper
adjustment of other controls may result in damage and will
often require extensive work by a qualified technician to
restore the video product to its normal operation.
e. If the video product has been dropped or damaged in any
way.
f. When the video product exhibits a distinct change in perfor-
mance this indicates a need for service.
20. Replacement Parts - When replacement parts are required,
be sure the service technician has used replacement parts
specified by the manufacturer or have the same characteris-
tics as the original part. Unauthorized substitutions may
result in fire, electric shock or other hazards.
21. Safety Check - Upon completion of any service or repairs to
this video product, ask the service technician to perform
safety checks to determine that the video product is in prop-
er operating condition.
22. Heat - This video product should be situated away from heat
sources such as radiators, heat registers, stoves, or other
products (including amplifiers) that produce heat.
13. Outdoor Antenna Grounding - If an outside antenna or cable
system is connected to the video product, be sure the anten-
na or cable system is grounded so as to provide some pro-
tection against voltage surges and built-up static charges.
Article 810 of the National Electrical Code, ANSI/NFPA
No. 70, provides information with regard to proper ground-
EN
–
–
3
1L25
A NOTE ABOUT RECYCLING
This product’s packaging materials are recyclable and can be reused. Please dispose of all materials in
accordance with your local recycling regulations.
Batteries should never be thrown away or incinerated but disposed of in accordance with your local
regulations concerning chemical wastes.
The serial number of this product may be found on the back of the DVD/VCR COMBINATION UNITS. This
serial number is unique to your machine. You should record the number and other vital information here and
retain this book as a permanent record of your purchase to aid identification in case of theft. Serial numbers are
not kept on file.
Date of Purchase
Dealer Purchase from
Dealer Address
Dealer Phone No.
Model No.
Serial No.
ABOUT COPYRIGHT
Unauthorized copying, broadcasting, public performance and lending of discs are prohibited.
This product incorporates copyright protection technology that is protected by method claims of certain U.S.
patents and other intellectual property rights owned by Macrovision Corporation and other rights owners. Use
of this copyright protection technology must be authorized by Macrovision Corporation, and is intended for
home and other limited viewing uses only unless otherwise authorized by Macrovision Corporation. Reverse
engineering or disassembly is prohibited.
SUPPLIED ACCESSORIES
RF Cable
Remote control
Two AA batteries
A/V cables
(approx. 3 feet (100 cm)
long) (WPZ0102TM015)
WPZ0901TM002
(NA209UD) or (NA259UD)
SYMBOLS USED IN THIS MANUAL
The following symbols below appear in some headings and notes in this manual, with the following meanings
VCR
: Description refers to playback of video cassette tapes.
DVD-V
: Description refers to playback of DVD video discs.
CD
: Description refers to playback of audio CDs.
MP3
: Description refers to playback of MP3 discs.
QUICK
: Description refers to the items to be set in the QUICK mode.
EN
–
–
4
1L25
TABLE OF CONTENTS
ꢀ LASER SAFETY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
DISC MENU. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
TITLE MENU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
STEP BY STEP PLAYBACK . . . . . . . . . . . . . . . . . . . . . . . . 23
RESUME . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
FAST FORWARD / REVERSE SEARCH . . . . . . . . . . . . . . . 23
SLOW FORWARD / SLOW REVERSE . . . . . . . . . . . . . . . . 23
ZOOM. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
TRACK. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
TITLE / CHAPTER SEARCH. . . . . . . . . . . . . . . . . . . . . . . . 24
TIME SEARCH. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
REPEAT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
PROGRAM. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
RANDOM PLAYBACK . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
MP3 PLAYBACK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
ON-SCREEN INFORMATION . . . . . . . . . . . . . . . . . . . . . . . 26
TRACK SELECTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
RANDOM PLAYBACK . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
PROGRAM. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
AUDIO LANGUAGE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
STEREO SOUND MODE . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
SUBTITLE LANGUAGE . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
CAMERA ANGLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
CHANGING THE ON-SCREEN DISPLAY . . . . . . . . . . . . . 28
PARENTAL CONTROL . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
MARKER SETUP SCREEN . . . . . . . . . . . . . . . . . . . . . . . . . 29
ꢀ DVD SETUP. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
AUDIO SETTING. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
BLACK LEVEL SETTING . . . . . . . . . . . . . . . . . . . . . . . . . . 30
VIRTUAL SURROUND . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
DISPLAY SETTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
LANGUAGE SETTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
ꢀ TROUBLESHOOTING GUIDE. . . . . . . . . . . . . . . . . . . . . . 32
ꢀ SPECIFICATIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
ꢀ IMPORTANT SAFEGUARDS . . . . . . . . . . . . . . . . . . . . . . . . 3
ABOUT COPYRIGHT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
SUPPLIED ACCESSORIES . . . . . . . . . . . . . . . . . . . . . . . . . . 4
SYMBOLS USED IN THIS MANUAL. . . . . . . . . . . . . . . . . . 4
ꢀ FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
ꢀ PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
ꢀ ABOUT THE DISCS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
PLAYABLE DISCS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
DISC TYPES. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
ꢀ OPERATING CONTROLS AND FUNCTIONS. . . . . . . . . . . 8
LOADING THE BATTERIES . . . . . . . . . . . . . . . . . . . . . . . . 11
ꢀ VCR/DVD SWITCHING . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
ꢀ HOOKUPS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
DVD/VCR TO TV CONNECTION. . . . . . . . . . . . . . . . . . . . 13
RF OUTPUT CHANNEL . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
CONNECTING TO A TV . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
CONNECTING TO A TV THAT HAS AN S-VIDEO INPUT
JACK OR COMPONENT VIDEO IN JACKS. . . . . . . . . . . . 14
CONNECTING TO AN AMPLIFIER EQUIPPED WITH
DIGITAL INPUT JACKS SUCH AS MD DECK OR DAT
DECK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
CONNECTING TO A DOLBY DIGITAL DECODER. . . . . . 15
CONNECTING TO AN ANALOG AUDIO. . . . . . . . . . . . . . 15
ꢀ SETUP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
AUTOMATIC CHANNEL SET UP. . . . . . . . . . . . . . . . . . . . 16
TO CHANGE THE ON-SCREEN LANGUAGE. . . . . . . . . . 17
CLOCK SET UP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
ꢀ PLAYBACK FUNCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
NORMAL PLAYBACK . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
AUTO REPEAT PLAYBACK . . . . . . . . . . . . . . . . . . . . . . . . 18
SEARCH FUNCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
ꢀ RECORDING FUNCTION . . . . . . . . . . . . . . . . . . . . . . . . . 19
NORMAL RECORDING . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
OTR (One Touch Recording). . . . . . . . . . . . . . . . . . . . . . . . . 19
TIMER RECORDING. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
HINTS FOR TIMER RECORDING . . . . . . . . . . . . . . . . . . . 20
ꢀ SPECIAL FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
COPYING A VIDEO TAPE. . . . . . . . . . . . . . . . . . . . . . . . . . 21
AUTO REWIND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
REAL TIME TAPE COUNTER. . . . . . . . . . . . . . . . . . . . . . . 21
ꢀ PLAYING A DISC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
BASIC PLAYBACK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
GENERAL FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
PAUSE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
INDICE
ꢀ CONTROLES DEL FUNCIONAMIENTO Y SUS FUNCIONES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
ꢀ CAMBIO DE VCR/DVD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
ꢀ CONEXIONES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
DVD/VCR A CONEXIÓN DE TV . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
CANAL DE SALIDA RF
CONECTANDO A UN TV
CONECTANDO A UN TV QUE TIENE TOMA DE ENTRADA DE S-VÍDEO o TOMAS DE ENTRADA DE VÍDEO
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
COMPONENTE
CONECTANDO A UN AMPLIFICADOR EQUIPADO CON TOMAS DE ENTRADA DIGITAL, TALES COMO PLATINA MD O
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
PLATINA DAT
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
CONECTANDO A UN DESCODIFICADOR DIGITAL DOLBY
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
CONECTANDO A UN AUDIO ANALÓGICO
ꢀ
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
PREPARACIÓN
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
PREPARACIÓN DE CANAL AUTOMÁTICA
PREPARACIÓN DE RELOJ
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
ꢀ REPRODUCCIÓN DE UN DISCO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
REPRODUCIENDO UN DVD, VIDEO O UN CD AUDIO
EN
–
–
5
1L25
FEATURES
¡Virtual Surround
DVD
Mode
¡Component Video Out Jacks
¡Dolby Digital sound
Jacks located on the back of the DVD/VCR COMBINA-
TION UNITS which are used to send high-quality video to
a TV via Component Video In Jacks.
This DVD/VCR COMBINATION UNITS can handle
Dolby Digital surround sound with 5.1 channels when con-
nected to a Dolby Digital decoder.
¡Bit rate indication
¡Still/fast/slow/step playback
¡DRC (Dynamic range control)
You can control the range of sound volume.
¡Random playback for audio CD and MP3
¡Program playback for audio CD and MP3
¡DVD menus in a desired language
¡Black Level Setting
VCR
Mode
¡Screen saver/Auto power-off functions
The screen saver program starts when there is no input
from the player for five minutes in the stop mode. When
the screen saver program is activated for 30 minutes, the
power is automatically turned off.
Hardware specifications
¡Auto Head Cleaner
¡Trilingual on-screen menu display selectable in
English, French, or Spanish
¡Subtitles in a desired language
¡Selecting a camera angle
¡181 channel capability PLL frequency synthesiz-
er tuner with direct station call
¡Choices for audio language and sound mode
¡Parental lock
(A cable converter box may be necessary to view scram-
bled cable channels.)
Automatic functions
¡Auto power on system
Automatically turns the VCR on when you insert the cas-
¡Automatic detection of discs
This player automatically detects if the loaded disc is
DVD, audio CD or MP3 on disc.
sette.
¡Playing an MP3 disc
¡Digital Auto Tracking (DTR)
Playback
¡Auto Repeat
¡Direct Search
¡On-screen display
Information about the current operation can be displayed
on the TV screen, allowing you to confirm the currently
active functions (such as program playback), on the TV
screen using the remote control.
¡2 Step Picture Search Operation
¡Index Search
¡Time Search
¡Search
Chapter search / Title search / Track search / Time search
Recording
¡Repeat
Chapter / Title / Track / Group / All / A-B
¡1Year, 8 events (including Daily and WeeklyTimer
Recording)
¡Zoom
¡OTR (One Touch Recording)
¡Marker
The part designated by user can be called back.
¡Resume Play
PRECAUTIONS
AVOID THE HAZARDS OF
INSTALLATION LOCATION
ELECTRICAL SHOCK AND FIRE
For safety and optimum performance of your
DVD/VCR COMBINATION UNITS:
• Do not handle the power cord with wet hands.
• Do not pull on the power cord when disconnecting it
from AC wall outlet. Grasp it by the plug.
• If, by accident, water is spilled on your DVD/VCR
COMBINATION UNITS, unplug the power cord
immediately and take the unit to our Authorized
Service Center for servicing.
• Install the DVD/VCR COMBINATION UNITS in a
horizontal and stable position. Do not place any-
thing directly on top of the DVD/VCR COMBINA-
TION UNITS. Do not place the DVD/VCR COMBI-
NATION UNITS directly on top of the TV.
• Shield it from direct sunlight and keep it away from
sources of intense heat. Avoid dusty or humid
places. Avoid places with insufficient ventilation for
proper heat dissipation. Do not block the ventilation
holes on the sides of the DVD/VCR COMBINATION
UNITS. Avoid locations subject to strong vibration
or strong magnetic fields.
• Do not put your fingers or objects into the DVD/VCR
COMBINATION UNITS cassette holder.
MOISTURE CONDENSATION WARNING
Moisture condensation may occur inside the unit when
it is moved from a cold place to a warm place, or after
heating a cold room or under conditions of high
humidity. Do not use the DVD/VCR COMBINATION
UNITS at least for 2 hours until its inside is dry.
EN
–
–
6
1L25
ABOUT THE DISCS
PLAYABLE DISCS
DISC TYPES
The following discs can be played back on this
DVD/VCR COMBINATION UNITS.
[
]
DVD
Data on a DVD is divided into sections called "titles", and
then into subsections called "chapters", each of which is
given a title or chapter number. Playback conditions are
preset on some DVD video discs, and these playback con-
ditions take priority over user operations on this player. If
a function you selected does not run as desired, refer to
the manual accompanying the disc.
¡
¡
¡
¡
¡
¡
DVD video
DVD+R/RW*
CD-R/RW*
DVD-R/RW*
Audio CD
MP3*
* Depending on the types or the writing method of the
medium some discs can not be played.
Example
• Some DVD-R/RW, DVD+R/RW, or CD-R/RW discs
made on personal computers, or on DVD recorders may
not be played back properly due to factors such as
scratches, dirt or special properties of the disc.
Title 1
Title 2
Chapter 1 Chapter 2 Chapter 3 Chapter 4 Chapter 1 Chapter 2
• Discs made on personal computers may not be played
back properly due to different environments or the set-
tings of the application you use. We recommend always
to use the standardized, properly formatted discs.
(Please contact the sales agency for more detail).
[
]
AUDIO CD
This player conforms to the NTSC color system. You can-
not play discs recorded in other color systems such as
PAL or SECAM.
Data on an audio CD is divided into sections called
“tracks”, each of which is given a track number.
¡Some discs include region codes as shown below.
Example
Track 1
Track 2
Track 3
Track 4
Track 5
Track 6
¡The number inside the symbol refers to a region of the
world, and a disc encoded in a specific region format
can only be played back on DVD/VCR COMBINA-
TION UNITS with the same region code.
The following discs cannot be played back on this
DVD/VCR COMBINATION UNITS.
[
]
MP3
Data on an MP3 is divided into sections called "groups",
and then into subsections called "tracks", each of which is
given a group or track number.
¡
¡
¡
DVD with region codes other than 1 or ALL.
DVD-ROM
Example
Group 1
Group 2
DVD-RAM (Never play back, otherwise malfunc-
tion may result.)
Track 1
Track 2
Track 3
Track 4
Track 1
Track 2
¡
¡
¡
¡
¡
CD-ROM
VSD
CDV (Only plays back the audio part.)
CD-G (Only plays back the sound.)
CD-I (Never play back, otherwise malfunction
may result.)
¡
¡
SACD
Photo CD (Never play back, otherwise malfunc-
tion may result.)
¡
Video CD (Never play back, otherwise malfunc-
tion may result.)
Any other discs without compatibility indications.
EN
–
–
7
1L25
OPERATING CONTROLS AND FUNCTIONS
FRONT PANEL
1
2
3
4
5
6 7
8
POWER
OPEN/CLOSE
CH-UP
STOP/EJECT
FF
OUTPUT
DVD
STOP
FWD
REW
REV
PLAY
VCR
REC
TIMER
REC
VIDEO
AUDIO
PLAY
DISC IN
CH-DOWN
PLAY
25
24 23 22
20
18 16 14 12
17
10
21
19
15
13
11
9
REMOTE CONTROL
6. POWER Button [page 16]
Press to turn the power on and off.
7. POWER Light (red)
55
26
POWER SPEED AUDIO
Light appears when the power is on.
8. STOP/EJECT Button (VCR)
EJECT Button
27
1
4
7
2
5
8
0
3
54
52
SKIP/CH.
Press to remove the tape from the VCR.
STOP Button
6
28
VCR/TV
SLOW
Press to stop the tape motion.
9. PLAY Button(VCR) [page 18]
Press to begin playback.
9
53
+
10
DISPLAY DVD
VCR
PAUSE
10. CH(ANNEL) Buttons [page 16]
51
49
29
31
33
In VCR mode, press to change TV channels on the
VCR; press to adjust the tracking during normal or
slow motion playback; press to remove vertical jitter
in a Still picture.
50
48
30
32
PLAY
STOP
11. AUDIO In Jack [page 21]
RECORD
MENU
Connect an audio cable coming from the audio out
jack of a camcorder, another VCR, or an audio source
here.
47
45
34
36
38
ENTER
46
35
37
SETUP
TITLE
RETURN
12. VIDEO In Jack [page 21]
SEARCH
MODE
CLEAR/
MODE ZOOM
Connect a video cable coming from the video out
jack of a camcorder, another VCR, or a video source
(laser disc player, camcorder, etc.) here.
13. FF Button (VCR) [page 18]
C.RESET
44
42
43
41
SUBTITLE ANGLE REPEAT
T-SET
A
B
39
40
Press to rapidly advance the tape, or view the picture
rapidly in forward during playback. (Forward
Search).
14. REW Button (VCR) [page 18]
Press to rewind the tape, or to view the picture rapid-
ly in reverse during the playback mode (Rewind
Search).
1. Disc loading tray
2. OPEN/CLOSE Button [page 22]
Press to insert discs into or remove them from the
tray.
15. REC Button [page 19]
3. DVD OUTPUT Light (Green) [page 12]
This light appears when the DVD output mode is
selected. You can only watch DVDs when the green
DVD OUTPUT light is on. To make the green DVD
OUTPUT light come on, press DVD on the remote
control or OUTPUT on the front panel.
Press once to start a recording. Press repeatedly to
start a One-Touch Recording.
16. REC Light [page 19]
Light appears during recording.
17. TIMER Light [page 19]
Light appears when the DVD/VCR is in standby
mode for a timer recording or during a One-Touch
Recording. It flashes if T-SET is pressed for a timer
recording, but there is no tape in the DVD/VCR. It
flashes when all timer recordings or One-Touch
Recordings are finished.
4. VCR OUTPUT Light (Green) [page 12]
This light appears when the VCR output mode is
selected. You can only watch tapes when the green
VCR OUTPUT light is on. To make the green VCR
OUTPUT light come on, VCR on the remote control
or OUTPUT on the front panel.
5. CASSETTE COMPARTMENT
EN
–
8 –
1L25
18. OUTPUT Button [page 12]
32. STOP Button
Press to select DVD mode or VCR mode.
GDVD mode
GYou can switch the output mode either by pressing
OUTPUT on the front panel, or by pressing DVD
or VCR on the remote control. However, if you
Press to stop the disc motion.
GVCR mode
Press to stop the tape motion.
press OUTPUT on the front panel first, you 33. RECORD Button [page 19]
need to re-select the corresponding mode by
pressing DVD or VCR on the remote control.
19. Remote Sensor Window
Press once to start a recording.
34. MENU Button
GDVD mode [page 23]
20. DISC IN Light (green)
Press to display the menu of the Disc.
GVCR mode [page 17]
Light appears when a disc is in the DVD Player.
21. PLAY Light (green)
Press to access the VCR menu.
35. TITLE Button [page 23]
36. SETUP Button [pages 28-31]
Press to enter DVD player setup mode.
Light appears during Disc playback.
22. FWD Button (DVD) [page 23]
Press to fast forward the Disc. Press PAUSE, then
press this button to begin slow motion playback. 37. ZOOM Button [page 24]
Press this button repeatedly to change the forward
speed of slow motion.
Enlarges part of a DVD-reproduced image.
38. MODE Button [pages 26,27,and 30]
Activates program playback or random playback
mode when playing CDs or MP3. Sets Black level
and virtual surround.
Press to skip Chapters or Tracks.
23. PLAY Button (DVD) [page 22]
Press to begin playback.
24. REV Button (DVD) [page 23]
Press to view the DVD picture in fast reverse motion
or to reverse playback of an Audio CD.
Press to skip Chapters or Tracks.
25. STOP Button (DVD) [page 22]
Stops operation of the disc.
39. SUBTITLE Button [page 27]
Press to select the desired subtitle language.
39. T-SET Button [page 19]
Press to put the VCR into standby mode for a timer
recording.
40. ANGLE Button [page 27]
Press to change the camera angle to see the sequence
being played back from a different angle.
41. REPEAT Button [page 25]
Repeats playback of the current disc, title, chapter or
track.
26. SPEED Button [page 19]
Press to select the VCR’s recording speed
(SP or SLP)
27. POWER Button
Press to turn the power on and off.
28. Number Buttons
42. A-B REPEAT Button [page 25]
Repeats playback of a selected section.
43. SEARCH MODE Button
GDVD mode [page 24]
Press to select numbered items in a menu.
+10
GDVD mode [page 24]
Use this button to enter number 10 and above.
GVCR mode [page 16]
Press to access or remove the Search display,
which allows you to go directly to a specific
Title/Chapter/Track/Time.
Press to select TV channels on the VCR.
To select channels, enter channel numbers as a
two-digit number for the quickest results. For
example, to select channel 6, press 0 then 6.
29. DISPLAY Button
GVCR mode [page 18]
Press to perform a Time Search or an Index Search.
44. CLEAR/C.RESET Button
GDVD mode [pages 24,25]
GDVD mode [page 28]
Press to reset the setting.
GVCR mode [page 16]
Press to reset the counter. Press to exit from the
MENU screen.
Press to access or remove the display screen during
DVD or Audio CD playback.
GVCR mode
Press to access or remove the VCR’s on-screen sta- 45. RETURN Button [page 30]
tus display.
GDVD mode
Returns to the previous operation.
46. Arrow Buttons
30. DVD Button [page 12]
Press to select DVD mode for the remote control.
GYou can switch the OUTPUT mode either by
pressing OUTPUT on the front panel, or by pressing
DVD or VCR on the remote control. However, if you
press OUTPUT on the front panel first, you need
to re-select the corresponding mode by pressing
DVD or VCR on the remote control.
31. h Button
Use when making settings while watching the dis-
play on a TV screen.
GDVD mode [pages 22-31]
Moves the cursor and determines its position.
GVCR mode [page 16]
p/o Buttons
Press to enter digits when setting program (For
example: setting clock or timer program). Press to
select the setting modes from the on screen menu.
B Button
GDVD mode [page 23]
Press to view the DVD picture in fast reverse
motion. Press PAUSE, then press this button to begin
slow motion playback. Press this button repeatedly to
change the reverse speed of slow motion.
GVCR mode [page 18]
When setting program (For example: setting clock
or timer program), press to determine your selec-
tion and proceed to the next step you want to input.
Press to determine the setting modes from the on
screen menu. Press to add or delete channel num-
Press to rewind the tape, or to view the picture rapidly
in reverse during the playback mode (Rewind Search).
EN
–
–
9
1L25
bers during channel preset.
s Button
51. PAUSE Button
GDVD mode [page 22]
Press to cancel a setting of timer program. Press to
correct digits when setting program (For example:
setting clock or timer program). Press to add or
delete channel numbers during channel preset.
Press to pause Disc playback. Press repeatedly to
advance the DVD picture step by step (or one
frame at a time).
GVCR mode [page 18]
47. ENTER Button
While recording, press to temporarily stop the
recording (pause). Press a second time to resume
normal recording. You can not pause a One-Touch
Recording. Or, press during tape playback to
freeze the picture. Press to advance the picture one
frame at a time during still mode.
52. SLOW Button [page 18]
During tape playback, press to view the video tape in
slow motion. Press again to resume normal playback.
This button does not affect DVD playback.
53. VCR/TV Button [page 19]
Use to select VCR or TV position.
GVCR Position
GDVD mode [page 22]
Press to accept a setting.
48. g Button
GDVD mode [page 23]
Press to fast forward the Disc. Press PAUSE, then
press this button to begin slow motion playback.
Press this button repeatedly to change the forward
speed of slow motion.
GVCR mode [page 18]
Press to rapidly advance the tape, or view the pic-
ture rapidly in forward during playback (Forward
Search).
49. PLAY Button
To view playback, to monitor video recording or to
watch TV using the VCR tuner.
GTV Position
To watch TV or to view one program while record-
ing another.
GDVD mode
Press to begin playback.
GVCR mode
Press to begin playback.
50. VCR Button [page 12]
54. SKIP/CH. Buttons
Press to select VCR mode for the remote control.
GYou can switch the OUTPUT mode either by
pressing OUTPUT on the front panel, or by pressing
DVD or VCR on the remote control. However, if you
press OUTPUT on the front panel first, you need
to re-select the corresponding mode by pressing
DVD or VCR on the remote control.
GDVD mode
Press to skip Chapters or Tracks.
GVCR mode
Press to change TV channels on the VCR.
55. AUDIO Button [page 27]
Press to select a desired audio language or sound
mode.
Notes
¡To use the remote control to operate the DVD/VCR
COMBINATION UNITS and its features, press DVD
on the remote control before pressing other DVD oper-
ation button. Verify that the green DVD OUTPUT
Light is on.
¡To use the remote control to operate the VCR and its
features, press VCR on the remote control before
pressing other VCR operation button. Verify that the
green VCR OUTPUT Light is on.
EN
–
–
10
1L25
REAR VIEW
56
57
58
59
60
DVD/VCR
VCR
DVD
AUDIO OUT
S-VIDEO COMPONENT AUDIO
DIGITAL
OUT
VIDEO OUT OUT
Y
AUDIO OUT
ANT-IN
L
AUDIO IN
VIDEO IN
R
Cb
Cr
L
COAXIAL
ANT-OUT VIDEO OUT
R
66
65
64
62
63
61
Audio In jacks of a television or other audio equip-
ment (DVD only).
56. ANT-IN (Antenna In) Jack
Connect your antenna, Cable Box, or Direct
Broadcast System.
63. S-VIDEO OUT Jack
Connect an optional S-Video cable here and to the S-
Video In jack of a television.
64. VIDEO IN Jack
Connect a cable coming from the video out jack of a
camcorder, another VCR, or an audio-visual source
(laser disc player, video disc player, etc.) here.
65. DVD/VCR VIDEO OUT Jack
Connect the yellow video cable (supplied) here and
to the TV’s Video In jack.
66. ANT-OUT (Antenna Out) Jack
Use the supplied RF coaxial cable to connect this
jack to the ANTENNA IN Jack on your TV.
57. DVD/VCR AUDIO OUT Jacks
Connect the supplied audio cables here and to the
Audio In jacks of a television or other audio equip-
ment.
58. AUDIO IN Jack
Connect an audio cable coming from the audio out
jack of a camcorder, another VCR, or an audio
source here.
59. AC Power Cord
Connect to a standard AC outlet to supply power to
the DVD/VCR COMBINATION UNITS.
60. COMPONENT VIDEO OUT Jacks
Connect optional component video cables here and
to the component Video In jacks of a television.
61. COAXIAL Jack
Notes
¡The S-VIDEO OUT jack, COAXIAL jack, and COM
PONENT VIDEO OUT jack are only useful in DVD
mode.
Caution: Do not touch the inner pins of the jacks
on the rear panel. Electrostatic discharge may
cause permanent damage to the player.
Connect an optional coaxial digital audio cable here
and to the Coaxial Digital Audio In jack of a decoder
or audio receiver.
62. DVD AUDIO OUT Jacks
Connect the supplied audio cables here and to the
LOADING THE BATTERIES
1. Open the battery compartment cover.
2. Insert two AA batteries (supplied), with each one oriented correctly.
3. Close the cover.
Notes
¡Do not mix alkaline and manganese batteries.
¡Do not mix old and new batteries.
EN
–
–
11
1L25
VCR/DVD SWITCHING
Since this product comprises VCR and DVD players, it is necessary to select the correct
output mode.
SWITCHING TO VCR MODE
SWITCHING TO DVD MODE
Press VCR on the remote control.
(Verify that the VCR OUTPUT Light is lit.)
Press DVD on the remote control.
(Verify that the DVD OUTPUT Light is lit.)
Notes
¡Pressing only OUTPUT on the front panel does not switch the mode of the remote control. You always need
to select the correct mode on the remote control too.
POWER
OPEN/CLOSE
POWER SPEED AUDIO
CH-UP
STOP/EJECT
FF
OUTPUT
STOP
FWD
DVD
REW
REV
PLAY
VCR
REC
TIMER
REC
VIDEO
AUDIO
PLAY
DISC IN
CH-DOWN
PLAY
1
4
7
2
5
8
0
3
SKIP/CH.
6
VCR/TV
SLOW
9
DVD OUTPUT Light
+
10
DVD button
VCR button
DISPLAY DVD
VCR
PAUSE
PLAY
STOP
OUTPUT
DVD
VCR
RECORD
MENU
VCR OUTPUT Light
ENTER
SETUP
TITLE
RETURN
SEARCH
MODE
CLEAR/
MODE ZOOM
C.RESET
OUTPUT button
SUBTITLE ANGLE REPEAT
T-SET
A
B
EN
–
–
12
1L25
HOOKUPS
CAUTION:
¡Be sure to turn off the DVD/VCR COMBINATION UNITS and equipment to be connected before connecting.
¡Read through the operation manual for the equipment to be connected.
¡Be sure that the colors of the jacks and plugs match up when using VIDEO/AUDIO cables.
¡Be sure to keep the DVD/VCR COMBINATION UNITS connection cables separate from the TV antenna cable
when you install the DVD/VCR COMBINATION UNITS, because it may cause electrical interference when
you are watching television programs.
DVD/VCR TO TV CONNECTION
RF OUTPUT CHANNEL
1. Disconnect the AC power cord of the TV from the If your TV does not have A/V terminals:
AC outlet.
1. Connect the DVD/VCR COMBINATION UNITS
to a TV using RF cable (see DVD/VCR TO TV
CONNECTION).
2. Disconnect the antenna or cable from the TV.
3. Connect the antenna or cable to the ANT-IN jack of
the DVD/VCR COMBINATION UNITS.
2. Select channel 3 on your TV.
4. Connect theDVD/VCR COMBINATION UNITS to 3. Press PLAY.
the TV using the RF cable.
¡If noise appears, change the RF output channel of
the VCR to channel 4 by pressing PLAY for 3 sec-
onds during playback.
5. Plug the AC power cords of the DVD/VCR COM-
BINATION UNITS and TV into the AC outlets.
¡There is case that the RF output channel does not
change by situation (For example, when you adjust
tracking using CHANNEL(UP/DOWN)).
In this case, stop the playback, and start the play-
back again. After that, press PLAY on the VCR for
3 seconds.
¡If there is a power failure or the DVD/VCR COM-
BINATION UNITS is unplugged for more than 30
seconds, the RF output channel setting will return to
CH3.
[VHF/UHF
[Back of the DVD/VCR]
[Indoor antenna]
combination antenna]
[Back of the
UHF/VHF combination TV]
RF cable
(supplied)
OR
OR
DVD/VCR
AUDIO OUT
VCR
ANT-IN
L
UHF/VHF
[Cable box or satellite box]
AUDIO IN
VIDEO IN
R
IN
ANT-OUT VIDEO OUT
OUT
From Cable or
Satellite Company
Note to CATV system installer
This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the NEC that pro-
vides guidelines for proper grounding and, in particular, specifies that the cable ground should be connected
to the grounding system of the building, as close to the point of cable entry as practical.
CONNECTING TO A TV
DVD/VCR
VCR
DVD
AUDIO OUT
S-VIDEO COMPONENT AUDIO
DIGITAL
Antenna/Cable signal
OUT
VIDEO OUT OUT
Y
AUDIO OUT
ANT-IN
AUDIO IN
DEO IN
Cb
Cr
L
A/V-compatible or
wide screen TV
COAXIAL
ANT-OUT VIDEO OUT
R
To ANT. IN
of TV
To VIDEO INPUT jack
To Right (red) and Left (white)
To AUDIO INPUT jacks
To VIDEO OUT jack
[Fig. 1]
To AUDIO OUT jacks
Notes
¡Connect the DVD/VCR COMBINATION UNITS directly to a TV. If the A/V cables are connected to a
VCR, pictures may be distorted due to the copy protection system.
EN
–
–
13
1L25
CONNECTING TO A TV THAT HAS AN S-VIDEO INPUT JACK OR
COMPONENT VIDEO IN JACKS
FOR TVs WITH S-VIDEO INPUT JACK
Use an S-Video cable (commercially available) in place of the yellow video cable to enjoy higher quality pic-
tures.
The S-Video connection only supplies video (picture) in the DVD mode of the DVD/VCR COMBINATION
UNITS. Therefore, in order to use the VCR features or view TV channels on the DVD/VCR COMBINATION
UNITS, you still need to either connect the RF cable between the ANT-OUT jack of the DVD/VCR COMBI-
NATION UNITS and the TV’s Antenna In jack, or connect the yellow video cable as described earlier (Fig.1).
To connect the supplied RF cable, see “DVD/VCR TO TV CONNECTION” on page 13.
DVD/VCR
VCR
DVD
AUDIO OUT
S-VIDEO COMPONENT AUDIO
DIGITAL
OUT
VIDEO OUT OUT
Y
AUDIO OUT
ANT-IN
L
A/V-compatible or
wide screen TV
AUDIO IN
VIDEO IN
R
Cb
Cr
COAXIAL
ANT-OUT VIDEO OUT
R
To S-VIDEO INPUT jack
To S-VIDEO OUT jack
To Right (red) and Left (white)
To AUDIO INPUT jacks
[Fig. 2]
To AUDIO OUT jacks
FOR TVs WITH
COMPONENT VIDEO IN JACKS
Use a component video cable (commercially available) in place of the yellow video cable to enjoy higher quality pic-
tures.
The component video connection only supplies video (picture) in the DVD mode of the DVD/VCR COMBINATION
UNITS. Therefore, in order to use the VCR features or view TV channels at the DVD/VCR COMBINATION UNITS,
you still need to either connect the RF coaxial cable between the ANT-OUT jack of the DVD/VCR COMBINATION
UNITS and the TV’s Antenna In jack, or connect the yellow video cable as described earlier (Fig. 1). To connect the
supplied RF cable, see “DVD/VCR TO TV CONNECTION” on page 13.
To Right (red) and Left (white)
AUDIO OUTPUT jacks
To Right (red) and Left (white)
AUDIO INPUT jacks
A/V-compatible
or
wide screen TV
DVD/VCR
VCR
DVD
AUDIO OUT
S-VIDEO COMPONENT AUDIO
DIGITAL
OUT
VIDEO OUT OUT
Y
AUDIO OUT
ANT-IN
L
AUDIO IN
VIDEO IN
R
Cb
Cr
L
COAXIAL
ANT-OUT VIDEO OUT
R
To COMPONENT VIDEO
INPUT jacks
[Fig. 3]
To COMPONENT VIDEO
OUT jacks
CONNECTING TO AN AMPLIFIER EQUIPPED WITH DIGITAL
INPUT JACKS SUCH AS MD DECK OR DAT DECK
Use an audio coaxial digital cable (commercially available) for the audio connections.
Connecting to an amplifier equipped with digital input jacks such as MD Deck or DAT Deck.
DVD/VCR
VCR
DVD
AUDIO OUT
S-VIDEO COMPONENT AUDIO
DIGITAL
OUT
VIDEO OUT OUT
Y
AUDIO OUT
ANT-IN
L
Amplifier equipped with digital
input jacks, MD deck,
DAT deck, etc.
AUDIO IN
VIDEO IN
R
Cb
Cr
L
COAXIAL
ANT-OUT VIDEO OUT
R
To COAXIAL DIGITAL
AUDIO OUT jack
To COAXIAL DIGITAL AUDIO INPUT jack
[Fig. 4]
Notes
¡The audio source on a disc in the 5.1 channel Dolby Digital surround format cannot be recorded as digital
sound by an MD or DAT deck.
¡Set DOLBY DIGITAL to OFF for audio output in the setup mode. Playing a DVD disc using incorrect set-
tings may generate noise distortion, and may also damage the speakers. (See page 29 to set DOLBY DIGITAL
to ON)
EN
–
–
14
1L25
CONNECTING TO A DOLBY DIGITAL DECODER
If using this DVD/VCR COMBINATION UNITS to play a DVD disc in 5.1 channel Dolby Digital surround, the
DVD/VCR COMBINATION UNITS outputs a Dolby Digital data stream from its COAXIAL DIGITALAUDIO
OUT jack. By hooking the DVD/VCR COMBINATION UNITS up to a Dolby Digital decorder, you can enjoy
a more convincing, realistic ambience with powerful and high-quality surround sound of a professional standard
such as can be heard in movie theaters.
Use an audio coaxial digital cable (commercially available) for the audio connections.
DVD/VCR
VCR
DVD
AUDIO OUT
S-VIDEO COMPONENT AUDIO
DIGITAL
OUT
VIDEO OUT OUT
Y
AUDIO OUT
ANT-IN
L
AUDIO IN
VIDEO IN
R
Cb
Cr
L
COAXIAL
ANT-OUT VIDEO OUT
R
Center speaker
Front speaker
(right)
Front speaker
(left)
To COAXIAL DIGITAL
AUDIO OUT jack
Dolby Digital
decoder
To COAXIAL DIGITAL
AUDIO INPUT jack
Subwoofer
Surround
speaker
(left)
Surround
speaker
(right)
[Fig. 5]
¡If the output is Dolby Digital audio, connect to a Dolby Digital decorder, and set DOLBY DIGITAL to ON
for audio output in the setup mode.
¡
Unless connected to a Dolby Digital decoder, set DOLBY DIGITAL to OFF for audio output in the setup mode.
Playing a DVD using incorrect settings may generate noise distortion, and may also damage the speakers.
Manufactured under license from Dolby Laboratories. “Dolby” and the double-D symbol are trademarks of
Dolby Laboratories.
CONNECTING TO AN ANALOG AUDIO
DVD/VCR
VCR
DVD
AUDIO OUT
S-VIDEO COMPONENT AUDIO
DIGITAL
OUT
VIDEO OUT OUT
Y
AUDIO OUT
ANT-IN
L
Stereo system
AUDIO IN
VIDEO IN
R
Cb
Cr
L
COAXIAL
ANT-OUT VIDEO OUT
R
To ANALOG AUDIO INPUT jacks
To Right (red) and Left (white)
AUDIO OUT jacks
[Fig. 6]
Notes
¡Be sure to turn off the power to all components in the system before connecting another component.
¡Refer to the Owner's Manuals for stereo systems and any other components to be connected to the DVD/VCR
COMBINATION UNITS.
EN
–
–
15
1L25
SETUP
AUTOMATIC CHANNEL SET UP
5 Begin channel preset by pressing B once.
VCR
The tuner scans and memo-
CH 01
rizes all active channels in
your area.
¡The VCR distinguishes between
standard TV channels and cable
channels.
You can automatically program the tuner to scan only
the channels you receive in your area.
AUTO SET UP
¡Channel memory programming is NOT needed
when you connect the VCR to a cable box or a satel-
lite box as in "DVD/VCR TO TV CONNECTION"
on page 13. In this case, select channel 3 on your TV.
Then, the channel you want to record or view may
be selected at the cable box or satellite box.
¡If noise appears, change the RF output channel of
the VCR to channel 4 by pressing PLAY for 3 sec-
onds during playback. Then select the same chan-
nel (CH4) on your TV.
6
After scanning, the tuner stops on the low-
est memorized channel. The TV screen
returns to TV mode.
¡If “AUTO SET UP” appears on the TV screen again,
check the cable connections. Press B once again and
the VCR will begin preset again.
TO SELECT A DESIRED CHANNEL
You can select the desired channel by using CHAN-
NEL (UP/DOWN) or by directly pressing Number on
the remote control.
¡Follow the steps below once. Repeat only if there is
a power failure or if the VCR is unplugged for more
than 30 seconds. (In these cases, the programmed
channels are erased.)
Note for using the Number:
¡You must follow the steps below before attempting
to play or record a video tape. If you want to play
or record a video tape BEFORE programming the
tuner, you can cancel it by pressing
¡When selecting cable channels which are higher
than 99, enter channel numbers as a three-digit num-
ber.(For example: 117, press 1,1,7)
¡You must precede single-digit channel numbers with
a zero (For example: 02, 03, 04 and so on).
CLEAR/C.RESET.
1
You need to connect the antenna or cable to
the VCR first. Then, connect the DVD /VCR
power plug to a standard AC outlet.
TO PRESET THE CHANNELS AGAIN
1
Press MENU until the main menu appears.
(If you have already set the clock, you only
have to press it once. If not, you have to
press it twice).
2
Turn on the TV and set the TV to channel 3.
¡If noise appears, change the RF output channel of
the VCR to channel 4 by pressing PLAY for 3 sec-
onds during playback. Then select the same channel
(CH4) on your TV. (See “RF OUTPUT
CHANNEL” on page 13 for the detail.)
2
3
Select “CHANNEL SET UP” by pressing
K
or L. Then, press B.
3
4
Turn on the VCR by pressing POWER. the
POWER light will come on.
Select “AUTO SET UP” by pressing K or L.
Then, press B.
¡After scanning, the tuner stops on the lowest memo-
rized channel.
Select the On Screen Language (“ENG-
LISH”, “FRANCAIS” or
“ESPAÑOL”) by pressing
K or L. Then, press B.
EN
–
–
16
1L25
TO ADD/DELETE CHANNELS
CLOCK SET UP
When scanning, some channels may be skipped due to
a weak signal. In such cases, you can add the channels
to the VCR memory manually.
VCR
1
Select main menu by pressing MENU.
1
Press MENU until the main menu
appears.(If you have already
¡If the clock is not set, the CLOCK SET menu
appears first. In this case, follow step [3].
- MENU -
TIMER PROGRAMMING
[OFF]
AUTO REPEAT
CHANNEL SET UP
CLOCK SET
set the clock, you only have
to press it once. If not you
have to press it twice).
LANGUAGE SELECT
AUDIO OUT
[ON]
TV STEREO
SAP
2
3
Select "CLOCK SET" by pressing K or L.
Then, press B.
Set the clock.
2
3
4
5
Select "CHANNEL SET UP" by pressing
or L. Then, press B.
K
1) Set the month
Select "MANUAL SET UP" by pressing K or
L. Then, press B.
Press K or L repeatedly.
Then, press B.
Enter the desired channel number by press-
ing K or L.
2) Set the day
Press K or L repeatedly.
Then, press B.
Add or Delete it from memory by pressing
B or s so that "ADD" or "DELETE" flashes
on the TV screen accordingly.
3) Set the year
Press K or L repeatedly.
Then, press B.
The day of the week will appear automatically.
6
Exit the Preset mode by pressing
CLEAR/C.RESET.
4) Set the hour
Press K or L repeatedly.
Then, press B.
TO CHANGE THE ON-SCREEN
LANGUAGE
5) Set the minute
Press K or L repeatedly.
Then, press B.
VCR
1
Press MENU twice to call up the main
menu. (If you have already set the clock,
you only have to press it once).
6) Set AM or PM
CLOCK SET
MONTH DAY
YEAR
Press K or L repeatedly.
03 17 MON 2003
/
HOUR MINUTE AM/PM
05
:
40
PM AM
PM
2
3
Select "LANGUAGE SELECT" by pressing
or L. Then, press B.
K
¡To go back one step, press s.
Select "ENGLISH", "FRANCAIS" or
"ESPAÑOL" by pressing K or L. Then, press
CLEAR/C.RESET.
4
Start the clock by pressing
CLEAR/C.RESET or B.
¡If you accidentally select Spanish or French and
need English: Press MENU and choose SELEC.
IDIOMA, or SELECTION LANGUE. Press B,
and select ENGLISH by pressing K or L.
Finally, press CLEAR/C.RESET.
EN
–
–
17
1L25
PLAYBACK FUNCTION
NORMAL PLAYBACK
2
3
Select "AUTO REPEAT" by pressing K or L.
VCR
Begin auto repeat playback by pressing
so that ON appears next to "AUTO
REPEAT".
B
1
Insert a prerecorded tape. The VCR will turn
on.
¡If the safety tab has been removed, the
VCR will start playback automatically.
¡If
the
on-screen
menu
still
remains,
CLEAR/C.RESET to exit the menu.
¡To cancel the Auto repeat mode, press B at step [3]
so that OFF appears next to "AUTO REPEAT".
2
Turn on the TV and set the TV to channel 3.
¡If noise appears, change the RF output channel of
the VCR to channel 4 by pressing PLAY for 3 sec-
onds during playback. Then select the same channel
(CH4) on your TV. (See “RF OUTPUT
CHANNEL” on page 13 for the detail.)
SEARCH FUNCTIONS
VCR
PICTURE SEARCH
If you want to skip or repeat a scene during playback,
press D or E.
3
Begin playback by pressing PLAY.
¡Tracking adjustment will be done automatically
(Digital Tracking function) when you start playback.
To adjust the tracking manually, press SKIP/CH. on
the remote or CHANNEL (UP/DOWN) on the VCR.
¡When a tape has reached the end, the VCR will
rewind the tape to the beginning, and eject the tape.
¡Press it again and the VCR will now search at super
high speed. (in the LP/SLP modes only).
INDEX SEARCH
An index mark will be assigned at the beginning of
each recordings you make. You may skip to a specific
marked point by following the steps below.
4
To stop playback, press STOP.
1
2
Press SEARCH MODE so that the Index
Search menu appears.
¡If no corresponding symbols appear on the display
when you press buttons such as PLAY, RECORD,
D or E, that means no cassette tape is in the
VCR. Please insert a tape.
Enter the number of recordings you wish to
skip by pressing K or
L
INDEX SEARCH
03
Counter Reset
within 30 seconds.
¡You can reset the counter by pressing
CLEAR/C.RESET on the remote control twice.
STILL/SLOW
3
Press B or { to start index search.
You can freeze the picture on TV screen by pressing
PAUSE during playback.
¡If you want to go in the forward direction, press B.
¡If you want to go in the reverse direction, press {.
¡If you want to stop search function, press STOP.
¡After index search, the VCR will play the tape auto-
matically.
¡You can advance the picture one frame at a time by
pressing PAUSE during the Still mode.
¡You cannot manually adjust the tracking of a still
picture. However, if the picture begins to vibrate
vertically during the still mode, you can stabilize the
picture by pressing CHANNEL (UP/DOWN).
¡If the picture is distorted or rolling vertically, adjust
the vertical hold control on your TV, if so equipped.
¡You can watch in the slow motion by pressing
SLOW during playback or the still mode.
TIME SEARCH
This feature allows you to go to a specific point on a
tape by entering the exact amount of time you wish to
skip in order to reach the point.
1
2
Press SEARCH MODE 2 times so that the
Time Search menu appears.
¡If a noise bar appears on the TV screen, you can
reduce it by pressing CHANNEL (UP/DOWN).
¡After the VCR has been in Still/Slow mode for 5
minutes, it will stop automatically to protect the tape
and the video head from damage.
TIME SEARCH
2 : 50
Enter your desired time to
skip by pressing K or
L
¡To return to playback, press PLAY.
within 30 seconds.
AUTO REPEAT PLAYBACK
3
Press B or { to start time search.
¡If you want to go in the forward direction, press B.
¡If you want to go in the reverse direction, press {.
¡If you want to stop search function, press STOP.
¡After time search, the VCR will play the tape auto-
matically.
VCR
This feature allows you to play a tape over and over.
1
Select main menu by pressing MENU.
EN
–
–
18
1L25
RECORDING FUNCTION
¡If a tape ends during OTR, the VCR will stop, eject
VCR
the tape, and switch to the DVD mode automatical-
ly as the TIMER light blinks. (If the DVD power is
off, the VCR will become STANDBY status).
¡When OTR is finished , the VCR turns off automat-
ically. To use the VCR again, press T-SET on the
remote, or STOP/EJECT on the DVD/VCR COM-
BINATION UNITS.
It may be UNLAWFUL to record copyrighted materi-
al without the consent of the copyright owner.
Accidental Erasure Prevention
To prevent accidental recording on a
recorded cassette, remove its record
safety tab. To record on it later, cover the
Record safety tab
hole with cellophane tape.
TIMER RECORDING
Before recording, make sure:
¡The desired channel is selected by pressing Number
on the remote control or CHANNEL (o/p). (If you
connected the VCR to a cable box or satellite box as
in "DVD/VCR TO TV CONNECTION" on page 13,
select channel 3 on your TV. Then, select the chan-
nel you want to record with the cable box or satellite
box. In this case, you can ONLY record and view the
SAME channel.)
¡If noise appears, change the RF output channel of
the VCR to channel 4 by pressing PLAY for 3 sec-
onds during playback. Then select the same channel
(CH4) on your TV.
VCR
You may set the VCR to start recording while you are
away. You can set eight programs to record on specif-
ic days, daily or weekly within 1 year period.
If you have not yet set the clock, "CLOCK SET"
appears. If so, follow the steps [3] and [4] in
"CLOCK SET UP" section on page 17. Then, set
the timer recording.
1
Insert a tape with its safety tab into the
DVD/VCR COMBINATION UNITS.
¡There is a tape with a safety tab in the VCR.
¡The desired recording speed is selected in SP (stan-
dard play) or SLP (super long play) mode by press-
ing SPEED on the remote control.
2
3
Select main menu by pressing MENU.
¡TV STEREO or SAP is selected.
TIMER PROGRAMMING
Select "TIMER PROGRAM-
MING" by pressing K or L.
Then, press B. The set up
screen is displayed.
PROG
DATE
12345678
-
Tape Speed
Recording/Playback Time
START TIME
END TIME
CHANNEL
Type of tape
SP mode
SLP mode
T60
1 hour
3 hours
T120
2 hours
6 hours
T160
2-2/3 hours
8 hours
REC SPEED
4
Set the timer.
¡To go back one step, press s.
NORMAL RECORDING
VCR
1
Begin the recording by pressing RECORD.
The REC Light comes on.
¡To temporarily stop recording or to resume it, press
PAUSE. After the VCR has been in Pause mode for
5 minutes, it will stop automatically to protect the
tape and the video head from damage.
1) Set the program number (1-8)
PROGRAM NUMBER
4
DATE
- - / - -
START TIME - - : - - - -
END TIME - - : - - - -
CHANNEL - -
REC SPEED - -
Program number which is not set up
flashes. Press K or L repeatedly
for the desired program number.
Then, press B.
2
Press STOP when the recording is completed.
Note
¡When you wish to watch another program while
recording, select desired channel on your TV. If
noise appears press VCR/TV.
2) Set the frequency of the recording
For once: Press K or L to point to
"ONCE".
PROGRAM NUMBER
4
ONCE
DAILY
WEEKLY
For daily (Monday~Friday): Press
or L to point to "DAILY".
For weekly: Press K or L to point
to "WEEKLY".
K
OTR (One Touch Recording)
VCR
Then, press B.
This feature allows you to set the recording length sim-
ply by pressing REC on the VCR.
ONE TIME PROGRAM
PROGRAM NUMBER
DATE - - / - -
START TIME - - : - - - -
END TIME - - : - - - -
CHANNEL - -
REC SPEED - -
3) Set the date
4
First, press K or L for the month.
Then, press B. Next, press K or
L for the day. Then, press B.
3
Press REC to begin OTR. The TIMER light
comes on. Change the recording length by
pressing REC repeatedly.
REC
OTR(0:30)
OTR(1:00).....
(Normal recording)
OTR(8:00)
OTR(7:30)
EN
–
–
19
1L25
¡When timer recordings are set, the TIMER light will
come on. To use the VCR as usual until the time for
the recording, press T-SET so that TIMER light dis-
appears. Press VCR/TV to choose the VCR position.
Select either VCR or DVD mode, then continue with
the other features as described in this manual.
ONE TIME PROGRAM
PROGRAM NUMBER
DATE 05 /12 MON
START TIME - - : - - - -
END TIME - - : - - - -
CHANNEL - -
REC SPEED - -
4) Set the start time
4
First, press K or L for the hour.
Then, press B. Next, press K or
L
for the minute. Then, press B. And
then, press K or L for AM or PM. Then, press B.
If you want to use the DVD player during
a VCR timer recording or while the
TIMER light is on or flashes.
¡You can use the DVD player while the TIMER light
is on or flashes, or during a timer recording. Press
POWER to turn on the DVD. Press DVD on the
remote control to choose DVD mode, then continue
with the other DVD features as described in this
manual. You don’t have to set the TIMER off to use
the DVD only.
ONE TIME PROGRAM
PROGRAM NUMBER
DATE 05 /12 MON
START TIME 07: 30 PM
END TIME - - : - - - -
5) Set the end time
4
Follow the instructions of
"Set the start time" to set
the end time.
CHANNEL
- -
REC SPEED - -
ONE TIME PROGRAM
6) Set the channel number
PROGRAM NUMBER
DATE 05 /12 MON
START TIME 07: 30 PM
END TIME 08: 30 PM
CHANNEL - -
REC SPEED - -
4
Press K or L repeatedly for the
desired channel number. Then,
press B.
If you connected the DVD/VCR COMBINATION UNITS to
a cable box or satellite box as in "DVD/VCR TO TV
CONNECTION" on page 13, select the DVD/VCR to channel 3
or 4 the same channel as RF output channel of the DVD/VCR.
Then, select the channel you want to record with the cable box
or satellite box.
TO STOP AN AUTOMATIC TIMER PRO-
GRAM ALREADY STARTED
Press STOP/EJECT on the DVD /VCR COMBINA-
TION UNITS.
TO CHECK, CORRECT, OR CANCEL AN
AUTOMATIC TIMER PROGRAM
Leave the cable box or satellite box on for timer recording.
ONE TIME PROGRAM
7) Set the tape speed
PROGRAM NUMBER
DATE 05 /12 MON
START TIME 07: 30 PM
END TIME 08: 30 PM
CHANNEL 16
4
1
Press T-SET.
Press K or L repeatedly for the
desired tape speed. Then, press B.
¡If the DVD output mode is selected, you have to
switch it to the VCR mode by pressing the VCR on
the remote control or the OUTPUT on the VCR.
REC SPEED SP
SP
SLP
5
6
To set another program, repeat step [4]. To
exit, press CLEAR/C.RESET.
2
3
Select main menu by pressing MENU.
Select "TIMER PROGRAMMING" by press-
ing K or L. Then, press B.
Press T-SET to set the timer.
¡The TIMER light on the DVD/VCR COMBINA-
TION UNITS comes on. TIMER RECORDING
WILL NOT BE ACTIVATED UNLESS YOU
PRESS T-SET.
4
Select the program number you want to
check by pressing K or L.
¡The details of the selected program appears on the
TV screen.
¡Go to the digit you want to change by pressing B or
s. Then, enter correct numbers by pressing o or p.
¡You may cancel the entire program by pressing
while the program number flashes.
HINTS FOR TIMER
RECORDING
s
VCR
¡If there is a power failure or the VCR is unplugged
for more than 30 seconds, the clock setting and all
timer settings will be lost.
¡If a tape ends during TIMER RECORDING, the
VCR will stop, eject the tape, and switch to the DVD
mode automatically as the TIMER light blinks. (If
the DVD power is off, the VCR will become
STANDBY status).
5
6
Press CLEAR/C.RESET to exit.
Press T-SET to return to timer stand-by
mode.
¡If a tape is not in the VCR or does not have a safe-
ty tab, the TIMER light flashes and timer recording
will not operate. Please insert a recordable tape.
¡When all timer recordings are finished, the TIMER
light will flash. To use the VCR again as usual, press
T-SET to disable the flashing TIMER light, then
press VCR/TV to select the VCR position. Select
either VCR or DVD mode, then continue with the
other features as described in this manual.
EN
–
–
20
1L25
SPECIAL FEATURES
COPYING A VIDEO TAPE
5
6
Press REC on the recording VCR.
VCR
Begin playback of the tape in the playing VCR.
¡For best results during dubbing, use the VCR’s front
panel controls whenever possible. The remote con-
trol might affect the playing VCR’s operation.
¡Always use video-quality shielded cables with
RCA-type connectors. Standard audio cables are not
recommended.
¡You can use a video disc player, satellite receiver, or
other audio/video component with A/V outputs in
place of the playing VCR.
You can make copies of video tapes made by friends or
relatives for your enjoyment.
Warning:
Unauthorized recordings of copyrighted video tapes
may be an infringement of copyright laws.
Connect the recording VCR (this unit), the playing
VCR (another source) and your TV using the follow-
ing diagram.
¡You can use the AUDIO/VIDEO input jacks on the
front panel of the DVD/VCR instead of using the
jacks on the back.
TO MONITOR THE RECORDING
[Recording VCR]
(this unit)
1
Turn on the TV and set the TV to channel 3.
¡If noise appears, change the RF output channel of
the VCR to channel 4 by pressing PLAY for 3 sec-
onds during playback. Then select the same channel
(CH4) on your TV. (See “RF OUTPUT
CHANNEL” on page 13 for the detail).
DVD/VCR
VCR
DVD
AUDIO OUT
S-VIDEO COMPONENT AUDIO
DIGITAL
OUT
VIDEO OUT OUT
Y
AUDIO OUT
ANT-IN
L
ADIO IN
VIDEO IN
R
Cb
Cr
L
COAXIAL
ANT-OUT VIDEO OUT
R
Coaxial cable
(supplied)
Audio/Video cables
(not supplied)
2
Press VCR/TV on the recording VCR.
[TV set]
(Use for monitoring)
OUT IN
AUDIO
VIDEO
AUTO REWIND
[Playing VCR]
When a tape reaches the end during recording, play-
back, or fast-forward, the tape will automatically
rewind to the beginning. After rewinding finishes, the
VCR will eject the tape and switch itself off.
¡The VCR will not rewind the tape automatically dur-
ing timer recording or One Touch Recording.
ANT in
(another source)
1
2
Insert a pre-recorded tape into the playing VCR.
Insert a tape with a safety tab into the
recording VCR.
REAL TIME TAPE COUNTER
3
4
Press SPEED on the recording VCR to select
the desired recording speed (SP/SLP)
.
¡This shows the elapsed recording or playback time
in hours, minutes, and seconds. (The displayed time
will not change during blank portions of the tape.)
¡The indication will appear when the tape is rewound
further than “0:00:00” on the tape counter.
Select the “L1” or “L2”position on the
recording VCR.
¡
When you use the A/V input jacks on the back of the
DVD/VCR, select "L1" position by pressing [0], [0], [1]
on the remote control or the CHANNEL (UP/DOWN).
¡
When you use the A/V input jacks on the front of the
DVD/VCR, select "L2" position by pressing [0], [0], [2]
on the remote control or the CHANNEL (UP/DOWN).
EN
–
–
21
1L25
PLAYING A DISC
Notes
BASIC PLAYBACK
¡A “prohibited icon” may appear at the top-right on
the TV screen during operation, warning that a pro-
hibited operation has been encountered by the DVD
or the disc.
DVD-V
CD
Getting started
¡With DVDs that use titles for playback program sig-
nals, playback may start from the second title, or it
may skip these titles.
¡During the playback of a two layered disc, pictures
may stop for a moment. This happens when the 1st
layer switches to the 2nd layer. This is not a mal-
function.
¡Turn on the power of the TV, amplifier and any other
components which are connected to the DVD.
¡Make sure the TV and audio receiver (commercially
available) are set to the correct channel.
¡Select DVD mode by pressing DVD on the remote
control or output on the front panel.
1
2
Press POWER.
Press OPEN/CLOSE to open disc loading
tray.
GENERAL FEATURES
DVD may contain menus to navigate the disc and
access special features. Press appropriate numerical
key or use Arrow (L/K/B/s) to highlight your selec-
tion in the DVD main menu and press ENTER to con-
firm.
3
Place the chosen disc in the tray, with the
label facing up.
Note
¡Unless stated, all operations described are based on
remote control use. Some operations can be carried
out using the menu bar on the TV screen.
PAUSE
4
Press PLAY.
DVD-V
CD
¡The tray will close automatically, and playback will
then start from the first chapter or track of the disc.
If the playback does not start automatically, press
PLAY.
¡When you playback the DVD which a title menu is
recorded, it may appear on the screen. In this case,
refer to “TITLE MENU” on page 23.
1
During playback, press PAUSE.
¡Playback will pause and sound will be muted.
2
To continue playback, press PLAY.
5
Press STOP twice to stop playback.
EN
–
–
22
1L25
DISC MENU
RESUME
DVD-V
DVD-V
CD
1
Press MENU.
¡The DVD main menu will appear.
1
During playback, press STOP.
¡Resume message will appear on the TV screen.
2
Press PLAY, playback will resume from the
point at which playback was stopped.
2
3
If the feature is not available,
may appear on the TV screen.
symbol
¡To cancel resume, press STOP twice.
If disc menu is available on the disc, audio
language, subtitle options, chapters for the
title and other options will appear for selec-
tion.
FAST FORWARD/REVERSE
SEARCH
DVD-V
CD
MP3
4
Press Arrow (L/K/B/s) to select an item,
and ENTER to confirm selection.
1
During playback, press g or h repeat-
edly to select the required forward or
reverse speed: x2, x8, x50, x100.
TITLE MENU
¡For audio CDs, the speed is fixed at ×16.
¡For MP3, the speed is fixed at ×8.
DVD-V
2
To return to normal playback, press PLAY .
1
Press TITLE.
¡The title menu will appear.
SLOW FORWARD /
SLOW REVERSE
2
3
If the feature is not available,
may appear on the TV screen.
symbol
DVD-V
During playback, press PAUSE.
Press g or h .
Press Arrow (L/K/B/s) to select an item,
and ENTER to confirm selection.
1
2
3
CALLING UP A MENU SCREEN
DURING PLAYBACK
Press g or h repeatedly to select the
required speed: 1/16, 1/8, 1/2 of the normal
playback.
For DVD-Vs
¡Press MENU to call up the DVD menu.
¡Press TITLE to call up the title menu.
Note
4
To return to normal playback, press PLAY.
¡Contents of menus and corresponding menu opera-
tions may vary between discs. Refer to the manual
accompanying the disc for details.
STEP BY STEP PLAYBACK
DVD-V
1
During playback, press PAUSE.
¡Playback will pause and sound will be muted.
2
3
The disc goes forward by one frame each
time PAUSE is pressed.
To exit step by step playback, press PLAY.
EN
–
–
23
1L25
Using SKIP
H
G
ZOOM
During playback, press SKIP G to move the next
track. Press it repeatedly to skip subsequent tracks.
Press SKIP H to go back to beginning of the current
track. Press it repeatedly to go to the previous tracks.
¡If SKIP is pressed while the playback is paused, the
playback will be paused again after skipping to the
next track.
DVD-V
The Zoom function allows you to enlarge the video
image and to pan through the enlarged image.
1
Press ZOOM during playback.
¡Playback will continue.
Note
¡SKIP
H
G are not available when playback is
stopped.
2
3
Press ZOOM repeatedly to select the
required zoom factor: x2, x4 or OFF.
TITLE / CHAPTER SEARCH
Use the Arrow (K/L/s/B) to move the
zoomed picture across the screen.
DVD-V
4
To exit zoom mode, press ZOOM to OFF.
1
Press SEARCH MODE once for the Chapter
search, twice for the Title search during
playback.
Notes
¡Zooming function does not work while disc menu is
shown.
/2
¡x4 zoom is not available on some discs.
TRACK
2
Enter the desired chapter/title number using
numerical buttons.
CD
¡Playback will start at the selected Chapter or Track.
¡Press CLEAR/C.RESET to erase the incorrect input.
¡For single digits press 0 first.
There are three ways to begin playback on an Audio
CD at a specific Track.
Using the Numerical buttons
TIME SEARCH
1
Press Numerical buttons to enter the
desired Track number.
DVD-V
CD
¡Playback will start at the selected track.
¡For single digit tracks (1-9), press a single number
(eg. track 3, press 3).
¡To play track 26, press +10, 2, 6 on the numerical
button.
1
2
During playback, press SEARCH MODE
three times (CD: twice) to display the Time
Search on the TV screen.
Using SEARCH MODE
Within 30 seconds, enter a desired disc
time using numerical buttons.
¡Playback will start at the specified time.
1
Press SEARCH MODE.
¡The track search display appears.
¡Press CLEAR/C.RESET to erase the incorrect input.
2
Within 30 seconds, select a desired track
number using numerical buttons.
¡For single digits press 0 first.
¡Playback will start at the selected track.
EN
–
–
24
1L25
REPEAT
PROGRAM
REPEAT are available only during playback.
CD
REPEAT TITLE / CHAPTER
DVD-V You may determine the order in which tracks will play.
1
In stop mode, press MODE.
¡The PROGRAM screen will appear.
To activate the repeat function, press REPEAT
during playback.
¡The repeat mode changes as described below every
time you press the button.
2
Press L or M to select a track, then press
ENTER.
CHAPTER
TITLE
OFF
¡Press CLEAR/C.RESET
to erase the most recently
entered program.
(repeat off)
(current chapter repeat) (current title repeat)
Notes
¡Repeat Title/Chapter is not available with some
scenes.
¡The REPEAT setting will be cleared when moving
to other title or chapter.
3
Press PLAY to play the programmed tracks.
REPEAT TRACK
Notes
CD
¡While the program is being played back, the STOP
works as follows.
¡Press STOP once and then PLAY again, playback
will restart from the point where STOP was pressed.
(Program continued)
¡Press STOP twice and then PLAY again, playback
will restart from the track in the usual way. (Program
cleared)
To activate the repeat function, press REPEAT
during playback.
¡The repeat mode changes as described below every
time you press the button.
TRACK
ALL
OFF
(repeat off)
(current track repeat)
(entire disc repeat)
¡Up to 99 programs can be entered.
¡If you like to repeat the current track in the program,
Notes
press REPEAT repeatedly until
TRACK appears
¡Track repeat setting will be cleared when moving to
other track.
during playback. If you like to repeat the entire pro-
gram press REPEAT repeatedly until
appears during playback.
ALL
¡Repeat playback does not function during A-B
REPEAT playback.
A-B REPEAT
DVD-V
CD
1
2
Press A-B REPEAT at your chosen starting
point.
A- appears briefly on the TV screen.
¡
¡
Press A-B REPEAT again at your chosen
end point.
A-B appears briefly on the TV screen, and the
repeat sequence begins.
3
Notes
To exit the sequence, press REPEAT A-B.
¡The A-B REPEAT section can only be set within the
current title (for DVDs), or current track (for audio
CDs).
¡A-B REPEAT is not available with some scenes in
DVD.
¡To cancel the A point which was set, press
CLEAR/C.RESET.
¡A-B REPEAT playback does not function during
title, chapter, track or all repeat playback.
EN
–
–
25
1L25
Notes
RANDOM PLAYBACK
¡Folders are known as Groups; files are known as
Tracks.
CD
3
¡MP3 files are accompanied by
icon.
¡Maximum of 255 folders can be recognized.
¡Maximum of 256 files can be recognized.
¡Up to 8 hierarchies can be created.
This shuffles the playing order of tracks instead of
playback in the sequence.
This player recommends the use of files recorded at
the below specifications:
¡Sampling frequency: 44.1kHz or 48kHz
¡Constant bit rate: 112kbps ~ 320kbps.
1
In stop mode, press MODE twice.
¡RANDOM screen
RANDOM
appears.
CD [AUDIO]
TOTAL 0:45:55
RANDOM PROGRAM
--no indication--
PLAY
INFORMATION
ON-SCREEN
MP3
You can check the MP3 files during playback.
2
Press PLAY to start random playback.
Note
1
Press DISPLAY.
¡The name of the file currently in play will be dis-
¡If you like to repeat the current track in the random
selection, press REPEAT repeatedly until
TRACK appears during playback. If you like to
repeat the entire random selection press REPEAT
played.
2
Press DISPLAY again to show the track
number, the repeat status, and the playback
status at the top of the screen.
repeatedly until
ALL appears during playback.
MP3 PLAYBACK
¡
will be displayed when repeat play has been
selected.
MP3
T - indicates Track repeat
When a CD with MP3 files is inserted in the
DVD/VCR, the MP3 menu will appear on the TV
screen.
G - indicates Group (folder) repeat
A - indicates Disc repeat
1
In stop mode, press Arrow (K/L) to select
the desired group track.
3
1
Press DISPLAY again to exit.
¡If a group is selected, press B or ENTER to go on to
the track selection screen.
Press Arrow (K /L ) to
choose a track, then press
B or ENTER.
TRACK SELECTION
MP3
Press SEARCH MODE during playback.
¡The FILE LIST will appear.
¡If a track is selected, press
B or ENTER to start play-
ing tracks. Starting from
the one you’ve just chosen the subsequent tracks
will be played.
¡Choose FIRST PLAY to start playback from the
beginning of the listed tracks.
¡Press TITLE to return to the first item.
2
Select a desired track using Arrow
(K/L/s/B).
¡Press B when you want to go to the next hierarchy.
¡Press s when you want to go back to the previous
hierarchy.
3
Notes
Press PLAY to start playing.
2
Press STOP to stop playback.
¡Press SEARCH MODE to exit.
¡Some selections may take a while to be recognized.
EN
–
–
26
1L25
RANDOM PLAYBACK
SUBTITLE LANGUAGE
MP3
DVD-V
The DVD allows you to select a language for subtitles
during DVD disc (if available) playback.
1
2
Press MODE twice while playback is
stopped.
1
2
Press SUBTITLE during playback.
Press PLAY to play the tracks in random
order.
Press SUBTITLE repeatedly to select your
desired subtitle language.
PROGRAM
¡The subtitle language will be displayed on the dis-
play bar at the top of the screen.
MP3
3
To turn off subtitles, press SUBTITLE
repeatedly until OFF appears.
This feature allows you to program a mp3 disc to play
in a desired sequence.
Notes
¡Pressing AUDIO may not work on some DVDs with
multiple audio languages (e.g. DVDs which allow
audio language setting on the disc menu).
¡Some discs allow audio language setting/subtitle
language setting on the disc menu. (Operation varies
between discs, so refer to the manual accompanying
the disc.)
1
Press MODE during playback is stopped.
¡The PROGRAM screen will appear.
2
Press Arrow (K/L) to select a track, then
press ENTER, to save it in a program.
¡Press CLEAR/C.RESET to erase the incorrect input.
¡If the desired language is not shown after pressing
SUBTITLE several times, the disc does not have
subtitles in that language.
3
Press PLAY to start programmed playback.
¡If you choose a Language that has a 3 letter language
code, the code will be displayed every time you
change the Subtitle language setting. If you choose
any other languages, ‘---’ will be displayed instead.
(Refer to page 31.)
AUDIO LANGUAGE
DVD-V
The DVD/VCR allows you to select a language during
DVD disc (if multi language available) playback.
CAMERA ANGLE
DVD-V
1
2
Press AUDIO during playback.
Some DVD discs contain scenes which have been shot
simultaneously from various angles. You can change
Press AUDIO repeatedly to select your
desired language.
the camera angle when the (
screen.
) icon appears on the
STEREO SOUND MODE
1
Press ANGLE during playback.
CD
¡The selected angle will be displayed on the display
bar at the top of the screen.
1
Press AUDIO repeatedly during playback to
select between STEREO, L-CH or R-CH.
2
Press ANGLE repeatedly to select your
desired angle.
¡STEREO - both right and left channels are active
(stereo)
L-CH - only left channel is active
R-CH - only right channel is active
Note
¡If the Virtual Surround setting is 1 or 2, the sound
mode will be fixed to STEREO, and can not be
changed.
EN
–
–
27
1L25
CHANGING THE ON-SCREEN
DISPLAY
PARENTAL CONTROL
DVD-V
DVD-V
CD
Parental Control limits the disc viewing that exceed
your settings. (with a password or playback will stop.)
This feature allows you to prevent discs with alterna-
tive scenes from being played by your children.
You can check the information about the current disc
by pressing DISPLAY on the remote control.
For DVD-Vs
PARENTAL LEVEL
1
Press DISPLAY during playback to show
current Chapter.
Parental Level allows you to set the rating level of
your DVD discs. Playback will stop if the disc’s rat-
ings exceed the level you set.
¡The elapsed and remaining
playing time of the current
chapter will be displayed.
9/49
0:00:00 -0:00:00
1
2
Press SETUP in STOP mode.
2
Press DISPLAY again to show current Title.
¡The elapsed and remaining playing time of the cur-
Press B to select CUSTOM, then press
ENTER.
rent title will be displayed.
3
Press Arrow (s/B) to select PARENTAL,
then press ENTER.
3
Press DISPLAY third time.
¡The BIT RATE and the current repeat setting will be
displayed.
¡If you are playing a dual layered disc, the layer num-
ber will also be displayed (L0: Layer 0 is playing.
L1: Layer 1 is playing).
PARENTAL
PARENTAL LEVEL ALL
4
Press DISPLAY the fourth time to remove
the display.
4
5
6
Enter your four-digit password then press
ENTER.
For audio CDs
Press Arrow (K/L) to select PARENTAL
LEVEL, then press ENTER.
1
Press DISPLAY during playback, the current
Track will be displayed on the TV screen.
¡The elapsed and remaining playing time of the cur-
rent track will be displayed.
Press Arrow (K/L) to select the desired
level.
2
Press DISPLAY again to show current Total
Track.
7
Press SETUP to exit
Notes
¡The elapsed and remaining playing time of the cur-
rent total track will be displayed.
¡When doing this for the first time, enter any 4 digits.
(except for 4737) That number will be used as the
password from the second time onward.
¡To change the password, press Arrow (K/L) to
select CHANGE at step 5, then press ENTER. Enter
the four-digit pass-word, then press ENTER.
¡With some DVDs, it may be difficult to find if they
are compatible with parental lock. Be sure to check
if the parental lock function operates in the way that
you have set.
3
Press DISPLAY third time to remove the dis-
play.
¡Record the password in case you forget it.
IF YOU FORGET THE PASSWORD
1
Press 4, 7, 3, 7 at step 4. Then enter your
new password.
¡Password will be cleared and parental level will be
set to ALL.
2
Proceed the above Steps 5-7 again.
EN
–
–
28
1L25
CONTROL LEVELS
2
3
Press Arrow (s /B) to select 1, 2, 3, 4, 5, 6,
7, 8, 9, or 10 and ensure that “- : - - : - -”
appears in the display.
¡
ALL
All parental lock is cancelled.
¡
Level 8
DVD software of any grade (adult/general/children)
can be played back.
When reaches the desired point, press
ENTER.
¡
Levels 7 to 2
¡The Title or Track and elapsed playing time will
appear in the TV screen.
Only DVD software intended for general use and
children can be played back.
¡
Level 1
4
To return to the Marker later, press SEARCH
MODE four times (CD: three times) during
playback and Arrow (s /B) to choose the
desired marker, then press ENTER.
Only DVD software intended for children can be
played back, with those intended for adult and
general use prohibited.
Notes
¡Opening the disc tray or turning off the power or
select AC at step 2 and press ENTER will erase all
Markers.
MARKER SETUP SCREEN
DVD-V
CD
¡To clear a marker, using Arrow (s / B), position the
cursor on to the marker number to be cleared and
press CLEAR/C.RESET.
¡You can mark up to 10 points.
Use markers to memorise your favourite places on a
disc.
1
Press SEARCH MODE twice (CD: three
times) during playback.
5
Press SEARCH MODE or RETURN to exit.
¡The display screen and Markers will appear on the
TV screen.
DVD SETUP
Dolby Digital:
Set to On when the unit is connected to a Dolby Digital
QUICK
AUDIO SETTING
Choose the appropriate Audio settings for your equip-
ment as it only affect during the playback of DVD
discs.
Decoder.
(ON: Output by Dolby Digital)
(OFF: Convert the Dolby Digital to PCM)
¡The default setting is ON.
DOWN SAMPLING:
¡Set to ON when outputting in 48 kHz.
¡The default setting is ON.
When playing disc with copyright Protection
¡If you select OFF, copyright protection will be acti-
vated and sound will be down sampled at 48kHz.
1
2
Press SETUP in STOP mode.
Press B to select CUSTOM, then press
ENTER.
¡CUSTOM mode will appear.
3
Press Arrow (s / B) to select AUDIO, then
press ENTER to confirm.
4
Press SETUP to exit.
AUDIO
DRC
OFF
ON
DOLBY DIGITAL
DOWN SAMPLING ON
4
Press Arrow (K/L) to select the below
items, then press ENTER.
DRC (Dynamic Range Control):
¡To compress the range of sound volume.
¡The default setting is OFF.
EN
–
–
29
1L25
BLACK LEVEL SETTING
DISPLAY SETTING
DVD-V
DVD-V
Adjust the Black Level Settings to make the black You can change certain aspects of the DVD display
parts of the picture brighter. screens, and on-screen messages.
1
Press MODE during playback.
1
2
Press SETUP in STOP mode.
ON
Press B to select CUSTOM, then press
ENTER.
¡CUSTOM mode will appear.
2
Press ENTER to switch ON/OFF.
ON: Makes the dark parts brighter.
3
Press Arrow (s /B) to select DISPLAY, then
press ENTER to confirm.
OFF: Shows the original picture as recorded.
3
Press MODE twice or RETURN to exit.
DISPLAY
TV ASPECT
4:3 LETTER BOX
ON
ANGLE ICON
AUTO POWER OFF ON
VIRTUAL SURROUND
DVD-V
CD
MP3
4
Press Arrow (K/L) to select the below
items, then press ENTER.
You can enjoy stereophonic visual space on your exist-
ing stereo system.
TV ASPECT:
¡Press Arrow (K/L) for an item selection, then press
QUICK
ENTER.
1
Press MODE twice (CD/MP3: once) during
¡Select 4:3 LETTER BOX for a black bars appears
on top and bottom of the screen.
¡Select 4:3 PAN & SCAN for a full height picture
with both sides trimmed.
playback.
OFF
¡Select 16:9 WIDE if a wide-screen TV is connected
to the DVD/VCR.
¡The default setting is 4:3 LETTER BOX.
ANGLE ICON:
¡Press ENTER repeatedly to turn Angle icon ON or
OFF.
¡The default setting is ON.
AUTO POWER OFF:
¡Press ENTER repeatedly to turn Auto Power off ON
or OFF.
2
3
Press ENTER to set it 1 (Natural effect) or 2
(Emphasized effect) or OFF.
Press MODE or RETURN to exit.
Note (for CD play only)
¡Virtual Surround will not be effective if the sound
mode is set to something other than STEREO.
¡The default setting is ON and it will turn the
DVD/VCR to off automatically after 35 minutes of
no use.
5
Notes
Press SETUP to exit.
¡Be sure to press SETUP, or the setting will not work.
EN
–
–
30
1L25
AUDIO:
¡Sets the audio language.
SUBTITLE:
¡Sets the subtitle language.
DISC MENU:
¡Sets the language for DVD menu.
LANGUAGE SETTING
DVD-V
Language options are not available with some discs.
PLAYER MENU:
¡Sets the language for the On-screen display.
QUICK
1
2
Press SETUP in STOP mode.
Press B to select CUSTOM, then press
ENTER.
5
Press Arrow (K/L) to select a setting, then
press ENTER.
¡CUSTOM mode will appear.
¡If OTHER is selected on the AUDIO, SUBTITLE or
DISC MENU screen, press four-digit number to
enter the code for the desired language. (Refer to the
language code list below.)
3
Press Arrow (s / B) to select LANGUAGE,
then press ENTER to confirm.
¡Only the languages supported by the disc can be
selected.
LANGUAGE
AUDIO
ORIGINAL
OFF
ENGLISH
ENGLISH
6
Note
Press SETUP to exit.
SUBTITLE
DISC MENU
PLAYER MENU
¡Language Setting for Audio and Subtitle is not avail-
able with some discs. Then use the Audio and the
Subtitle button. Details are on page 27.
4
Press Arrow (K/L) to select the next items,
then press ENTER.
¡If you want to return to LANGUAGE SETTING
MENU, press Arrow (s ).
Language
Code
Language
Frisian
Code
5271
5358
5747
5051
5158
5758
5360
5367
5447
5569
5455
5467
Language
Malay
Code
5965
5958
5966
5955
5964
5961
5960
6047
6051
6061
Language
Somali
Spanish [SPA]
Sundanese
Swahili
Swedish [SWE]
T
Code
6561
5165
6567
6569
6568
A-B
Abkhazian
Afar
Afrikaans
Albanian
Amharic
Arabic
Armenian
Assamese
Aymara
Azerbaijani
Bashkir
Basque
Bengali;Bangla
Bhutani
Bihari
Bislama
Breton
4748
4747
4752
6563
4759
4764
5471
4765
4771
4772
4847
5167
4860
5072
4854
4855
4864
4853
5971
4851
Galician
Malayalam
Maltese
Maori
Georgian
German [GER]
Greek [GRE]
Greenlandic
Guarani
Gujarati
Hausa
Hebrew
Hindi
Hungarian [HUN]
I-K
Icelandic [ICE]
Indonesian
Interlingua
Interlingue
Inupiak
Irish [IRI]
Italian [ITA]
Japanese [JPN]
Javanese
Kannada
Kashmiri
Kazakh
Kinyarwanda
Kirghiz
Kirundi
Marathi
Moldavian
Mongolian
Nauru
Tagalog
Tajik
Tamil
6658
6653
6647
6666
6651
6654
4861
6655
6661
6665
6664
6657
6669
Nepali
Norwegian [NOR]
O-R
Occitan
Tatar
Telugu
6149
6164
6159
6247
6265
5247
6258
6266
6367
6459
6461
6467
Thai
Oriya
Oromo(Afan)
Panjabi
Pashto;Pushto
Persian
Polish
Portuguese [POR]
Quechua
Rhaeto-Romance
Romanian [RUM]
Russian [RUS]
S
Samoan
Sangho
Sanskrit
Scots Gaelic
Serbian
Serbo-Croatian
Sesotho
Setswana
Shona
Sindhi
Tibetan
Tigrinya
Tonga
5565
5560
5547
5551
5557
5347
5566
5647
5669
5760
5765
5757
6469
5771
6460
5761
5767
Tsonga
Turkish [TUR]
Turkmen
Twi
Bulgarian
Burmese
Byelorussian
U-Z
Ukrainian
Urdu
Uzbek
6757
6764
6772
6855
6861
4971
6961
7054
5655
7161
7267
C-E
Cambodian
Catalan
5759
4947
7254
4961
5464
4965
5047
6058
5160
5161
5166
Vietnamese
Volapuk
Welsh
Wolof
Xhosa
Yiddish
Yoruba
Zulu
Chinese [CHI]
Corsican
Croatian
6559
6553
6547
5350
6564
6554
6566
6660
6560
6550
6555
6565
6557
6558
Czech
Danish [DAN]
Dutch [DUT]
English [ENG]
Esperanto
Estonian
Korean [KOR]
Kurdish
L-N
Laothian
Latin
Latvian;Lettish
Lingala
Lithuanian
Macedonian
Malagasy
5861
5847
5868
5860
5866
5957
5953
F-H
Faroese
Fiji
Finnish [FIN]
French [FRE]
5261
5256
5255
5264
Singhalese
Siswat
Slovak
Slovenian
If you choose a Language that has a 3 letter language code, the code will be displayed every time you change
the Audio or Subtitle language setting on page 27. If you choose any other languages, ‘---’ will be displayed
instead. (3 letter language code is written in bracket.)
EN
–
–
31
1L25
TROUBLESHOOTING GUIDE
If the DVD/VCR COMBINATION UNITS does not perform properly when operated as instructed in this
Owner's Manual, check the player consulting the following checklist.
PROBLEM
No power.
CORRECTIVE ACTION
D
V
D
• Make sure the power plug is connected to an AC outlet.
• Make sure the power is turned on.
The player does not respond to. • Check if the power plug is connected to an AC outlet.
the remote control.
• Check the batteries in the remote control.
• Aim the remote control directly at the remote sensor. If necessary, remove all the
obstacles between the sensor and the remote.
• You have to be within 23 feet of the player.
• Check if the correct mode is selected. If not switch the mode by pressing DVD or
VCR ,whichever you need, on the remote control.
V
C
R
• Check if a cassette tape is in the VCR.
Timer recording is impossible. • Make sure the timer recording is set correctly.
• Make sure the power is off.
V
C
R
• Make sure the VCR clock is set correctly.
Cannot go into Record mode. • Make sure the tape has a safety tab. If needed, cover the hole with cellophane tape.
• Put he player in VCR mode. Press VCR on the remote control so that the green VCR
OUTPUT light is lit.
Playback picture is partially noisy • Adjust tracking control for a better picture by pressing CHANNEL (UP/DOWN) on the
DVD/VCR COMBINATION UNITS.
Cannot view a tape but the
• Head cleaning may be necessary. Refer to “AUTO HEAD CLEANING” .
• Make sure the VCR is not in the Menu mode.
.
audio is OK
No, or poor, playback picture.
• Change the RF output channel to CH4. Then select the same channel on the TV.
• Fine tune your TV.
TV programs cannot be seen
normally.
• Re-check the ANT. IN and ANT. OUT connections. See page 13.
• Press VCR/TV.
• Press VCR on the remote control to put it in the VCR mode. Check if the green VCR
OUTPUT light is lit. Then, set it to the TV position by pressing VCR/TV.
Video or color fades in and out
when making a copy of a video tape.
•
You cannot copy a copyrighted video tape. You are experiencing copy guard protection.
Cannot remove the tape.
• Check if the player is in the VCR mode. If not, press VCR on the remote control to switch
the mode.
No picture.
• Connect the video cables firmly.
D
V
D
• Insert a correct video disc that plays on this player.
• Press DVD on the remote control. Check if the DVD OUTPUT Light is lit. Then try other
DVD feature.
• Insert the disc.
• Clean the disc.
.
Disc cannot be played
• Place the disc correctly, with the label side up.
• Cancel the parental lock or change the control level.
• Connect the audio cables firmly.
.
No sound
• Turn the power of the audio component on.
• Correct the audio output settings.
• Correct the input settings on the audio component.
• This player does not support DTS audio. This is not a malfunction.
• Connect the player directly to the TV.
.
No DTS audio is output
.
Distorted picture
•
There are some cases where pictures may be slightly distorted, which are not a sign of a mal-
function.
• Although pictures may stop for a moment, this is not a malfunction.
Audio or subtitle language
does not match the set up
The camera angle cannot be
changed
•
The selected language is not available for audio or subtitles on the DVD.
This is not a malfunction
The DVD does not contain sequences recorded from different camera angles.
This is not a malfunction
•
Audio or subtitle language
cannot be changed
• The DVD does not contain audio source or subtitles in the selected language.
This is not a malfunction.
“Prohibited icon” appears on the • That operation is prohibited by the player or the disc.
screen, prohibiting an operation This is not a malfunction.
Notes
Some functions are not available in specific modes, but this is not a malfunction. Read the description in this
Owner’s Manual for details on correct operations.
¡Playback from a desired track and random playback are not available during program playback.
EN
–
–
32
1L25
MAINTENANCE
AUTO HEAD CLEANING
SERVICING
¡Should your DVD/VCR COMBINATION UNITS
become inoperative, do not try to correct the prob-
lem by yourself. There are no user-serviceable parts
inside. Turn off, unplug the power cord, and please
call our help line at 1-800-256-2487 to locate an
Authorized Service Center.
• Automatically cleans video heads as you insert or
remove a cassette, so you can see a clear picture.
• Playback picture may become blurred or interrupted
while the TV program reception is clear. Dirt accu-
mulated on the video heads after long periods of
use, or the usage of rental or worn tapes can cause
this problem. If a streaky or snowy picture appears
during playback, the video heads in your
CLEANING THE CABINET
DVD/VCR COMBINATION UNITS may need to
be cleaned.
¡Use a soft cloth slightly moistened with a mild deter-
gent solution. Do not use a solution containing alco-
hol, spirits, ammonia or abrasives.
1. Please visit your local Audio/Video store and pur-
chase a good quality VHS Video Head Cleaner.
2. If a Video Head Cleaner does not solve the prob-
lem, please call our help line at 1-800-256-2487 to
locate an Authorized Service Center.
CLEANING DISCS
¡When a disc becomes dirty, clean it with a cleaning
cloth. Wipe the disc from the center out. Do not wipe
in a circular motion.
NOTES:
¡Do not use solvents such as benzine, thinner, com-
mercially available cleaners, detergent, abrasive
cleaning agents or antistatic spray intended for ana-
logue records.
• Remember to read the instructions included with the
video head cleaner before use.
• Clean video heads only when problems occur.
CLEANING THE DISC LENS
¡If the player still does not perform properly when it
is operated while referring to the relevant sections
and to “TROUBLESHOOTING GUIDE” in this
Owner’s Manual, the laser optical pickup unit may
be dirty. Consult your dealer or an Authorized
Service Center for inspection and cleaning of the
laser optical pickup unit.
DISC HANDLING
¡Use discs which have the following logos on them.
(Optical audio digital discs.)
Recordable
ReWritable
¡Handle the discs so that fingerprints and dust do not
adhere to the surfaces of the discs.
¡Always store the disc in its protective case when it is
not used.
Make your contribution to the environment!!!
• Used up batteries do not belong in the dust bin.
• You can dispose of them at a collection point for used up batteries or special waste.
Contact your council for details.
EN
–
–
33
1L25
SPECIFICATIONS
Product type:
Discs:
DVD player with Video Cassette Recorder
DVD video
Audio CD
Video Cassette tape
Converter output:
Power source:
VHF Channel 3 or 4.
120 V AC +/- 10%, 60 Hz +/- 0.5%
24 W (standby: 7.0 W)
41˚F (5°C) to 104˚F (40°C)
W 17-1/8” (435 mm)
H 4” (99 mm)
Power consumption:
Operating temperature:
Dimensions:
D 8-7/10” (218 mm)
8.8 lbs (3.7 kg)
Weight:
¡Designs and specifications are subject to change without notice.
¡If there is a discrepancy between languages, the default language will be English.
EN
–
–
34
1L25
CONTROLES DEL FUNCIONAMIENTO Y SUS FUNCIONES
PANEL DELANTERO
1
2
3
4
5
6
7
8
POWER
OPEN/CLOSE
CH-UP
STOP/EJECT
FF
OUTPUT
DVD
STOP
FWD
REW
REV
PLAY
VCR
REC
TIMER
REC
VIDEO
AUDIO
PLAY
DISC IN
CH-DOWN
PLAY
25
24 23 22
20
18 16 14 12
17
10
21
55
19
15
13
11
9
PANEL REMOTO
9. Botón PLAY (VCR)
Presione para comenzar reproducción.
10. Botones CHANNEL
26
POWER SPEED AUDIO
En el modo VCR, presione para cambiar canales TV en
el DVD/VCR; presione para ajustar el seguimiento
durante reproducción de movimiento normal o lento;
presione para remover fluctuaciones verticales en una
imagen fija.
27
1
4
7
2
5
8
0
3
54
SKIP/CH.
6
28
VCR/TV
SLOW
9
53
11. Tomas AUDIO IN
+
10
52
Conecte aquí cables de audio procedentes de las tomas
de salida de audio de un camcorder, otro VCR o una
fuente de audio.
DISPLAY DVD
VCR
PAUSE
51
49
29
31
33
50
48
30
32
PLAY
STOP
12. Toma VIDEO IN
Conecte aquí un cable de videó procedente de la toma
de salida de videó de un camcorder, otro VCR o una
fuente de videó (reproductor de discos láser, camcorder,
etc.).
RECORD
MENU
47
45
34
36
38
ENTER
46
35
37
SETUP
TITLE
RETURN
13. Botón FF (VCR)
SEARCH
MODE
CLEAR/
MODE ZOOM
C.RESET
Presione para avanzar rápidamente la cinta o ver la ima-
gen rápidamente en avance durante reproducción.
(Búsqueda en Avance).
44
42
43
41
SUBTITLE ANGLE REPEAT
T-SET
A
B
39
40
14. Botón REW (VCR)
Presione para rebobinar la cinta o para ver la imagen
rápidamente en inversión durante el modo de reproduc-
ción.(Búsqueda en Rebobinado).
1. Bandeja de carga del disco
2. Botón OPEN/CLOSE
15. Botón REC
Presione para insertar discos en o removerlos de la ban-
deja de disco.
3. Luz DVD OUTPUT (verde)
Presione una vez para iniciar una grabación. Presione
repetidamente para iniciar un Grabación de Un-Toque.
16. Luz REC
Se enciende durante la grabación.
17. Luz TIMER
Esta luz aparece cuando el DVD/VCR está en modo
DVD. Usted sólo puede mirar DVDs cuando la Luz
DVD OUTPUT verde está encendida. Para hacer que la
Luz DVD OUTPUT verde se encienda, presione el
Botón DVD en el control remote o el Botón OUTPUT
en el panel delantero.
Esta luz brilla cuando el DVD/VCR está en el modo
espera para una grabación con temporizador o durante
una grabación de Un-Toque, Parpadea si se presiona
Botón T-SET para una grabación con temporizador,
pero no hay cinta en el DVD/VCR. Parpadea cuando
todas las grabaciones con temporizador o grabaciones
de Un-Toque han terminado.
4. Luz VCR OUTPUT (Verde)
Esta luz aparece cuando el DVD/VCR está en el modo
VCR. Usted puede sólo mirar cintas cuando la Luz VCR
OUTPUT verde está encendida. Para hacer que la Luz
VCR OUTPUT verde se encienda, presione el Botón
VCR en el control remote o el Botón OUTPUT en el
panel delantero.
18. Botón OUTPUT
Presione para seleccionar el modo DVD o el modo
VCR.
GUsted puede cambiar el modo de salida ya presionan-
do el Botón OUTPUT en el panel delantero o ya pre-
sionando el Botón DVD o VCR en el control remote.
Sin embargo, si usted presiona el Botón OUTPUT
en el panel delantero primero, usted necesita
volver a seleccionar el modo correspondiente pre-
sionando el Botón DVD o el Botón VCR en el con-
trol remote.
5. CASSETTE COMPARTMENT
6. Botón POWER
Presione para conectar y desconectar la alimentación.
7. Luz POWER (rojo)
Se enciende cuando la energía está encendido.
8. Botón STOP/EJECT (VCR)
G Botón de expulsión
Púlselo para sacar el videocasete de la
videograbadora.
19. Ventanilla de Sensor Remoto.
20. Luz DISC IN (verde)
Se enciende cuando un disco está en el jugador de DVD.
21. Luz PLAY (verde)
G Botón Stop
Presione detener el movimiento de la cinta.
Se enciende durante aparato de lectura del disco.
SP
–
–
35
1L25
22. Botón FWD (DVD)
34. Botón MENU
Presione para avanzar rápidamente el Disco. Presione el
Botón PAUSE, luego presione el Botón FWD iniciar a
reproducción en movimiento lento. Presione el Botón
FWD repetidamente para cambiar la velocidad de
avance del movimiento lento.
GModo DVD
Presione para visualizar el menú del Disco.
GModo VCR
Presione para tener acceso al menú VCR.
35. Botón TITLE
Presione para saltar Capítulos o Pistas.
23. Botón PLAY (DVD)
36. Botón SETUP
Presiónelo para entrar en el modo de preparación del
reproductor DVD.
Comienza la reproducción del contenido del disco.
24. Botón REV (DVD)
37. Botón ZOOM
Amplía parte de una imagen reproducida-DVD.
38. Botón MODE
Presione para ver la imagen DVD en movimiento de
inversión rápida o para invertir la reproducción de un
DC de Audio.
Activa modo de reproducción de programa o reproduc-
ción aleatoria cuando se reproducen CDs o MP3. Ajusta
Nivel de negro o TruSurround SRS.
39. Botón SUBTITLE
Presione para saltar Capítulos o Pistas.
25. Botón STOP (DVD)
Detiene la operación del disco.
26. Botón SPEED
Presione para seleccionar un idioma de subtítulo deseado.
40. Botón ANGLE
Presiona para seleccionar la velocidad de grabación de
VCR (SP o SLP)
Presione para cambiar el ángulo de cámara para ver la
secuencia que se está reproduciendo desde un ángulo
diferente.
27. Botón POWER
Presione para conectar y desconectar la alimentación.
28. Botones numéricos
41. Botón REPEAT
GModo DVD
Repite la reproducción del disco, título, capítulo o pista
actual.
Presiónelos para seleccionar elementos numerados
en un menú.
42. Botón A-B REPEAT
Repite la reproducción de una sección seleccionada.
43. Botón SEARCH MODE
GModo DVD
+10
Use este botón para ingresar números inguales o
mayores que 10.
Presione para tener acceso o remover la indicación de
búsqueda, que le permite ir directamente a un
Título/Capítulo/Pista/Tiempo especificado.
GModo VCR
GModo VCR
Presione para seleccionar canales de TV en el
DVD/VCR. Para seleccionar canales, entre números
de canal como un número de dos dígitos para los
resultados más rápidos. Por ejemplo, para seleccionar
canal 6, presione 0.6.
Presione para avanzar o rebobinar rápidamente la
cinta a una longitud específica de tiempo.
44. Botón CLEAR/C.RESET
GModo DVD
29. Botón DISPLAY
GModo DVD
Presione para reponen el ajuste.
GModo VCR
Presione para tener acceso o remover la pantalla de
visualización durante reproducción DVD o CD de
audio.
Presione para reponer el contador. Presione para salir
de la pantalla MEMU.
GModo VCR
45. Botón RETURN
Presione para tener acceso o remover visualización de
estado en pantalla de VCR.
GModo DVD
Vuelve a la operación previa.
30. Botón DVD
46. Botones de flecha
Presione antes de utilizar el control remote para fun-
ciones DVD.
Utilícelos cuando realice los ajustes mientras tiene la
visualización en la pantalla de TV.
GModo DVD
GUsted puede cambiar el modo de salida ya presionan-
do el Botón OUTPUT en el panel delantero o ya pre-
sionando el Botón DVD o VCR en el control remote.
Sin embargo, si usted presiona el Botón OUTPUT
en el panel delantero primero, usted necesita
volver a seleccionar el modo correspondiente pre-
sionando el Botón DVD o el Botón VCR en el con-
trol remote.
Mueve el cursor y determina su posición.
GModo VCR
Botones p/o
Pulse estos para introducir los dígitos cuando ajuste
programa (por ejemplo: ajuste de reloj o programa
con temporizador). Pulse para seleccionar los modos
de ajuste del menú en pantalla.
31. Botón
h
GModo DVD
Botón
B
Cuando ajuste programa (por ejemplo: ajuste de reloj
o programa con temporizador), pulse para determinar
su selección y proceder al siguiente paso que usted
desea introducir. Pulse para determinar los modos de
ajuste del menú en pantalla. Pulse para añadir o bor-
rar los números de canal durante el preajuste de canal.
Presiónelo para ver la imagen de un DVD en
retroceso rápido. Presione PAUSE y luego presione
este botón para iniciar la reproducción a cámara
lenta. Presione repetidamente este botón para
cambiar la velocidad de retroceso de la reproducción
a cámara lenta.
Botón
s
GModo VCR
Pulse para cancelar un ajuste de programa con tem-
porizador. Pulse para corregir los dígitos cuando se
ajusta un programa (por ejemplo: ajuste de reloj o
programa con temporizador). Pulse para añadir o bor-
rar los números de canal durante el preajuste de canal.
Presione para rebobinar la cinta o para ver la imagen
rápidamente en inversión durante el modo de repro-
ducción.(Búsqueda en Rebobinado).
32. Botón Stop
GModo DVD
47. Botón ENTER
Presiónelo para detener el disco.
GModo VCR
GModo DVD
Presione para aceptar un ajuste.
Presiónelo para detener la cinta.
33. Botón RECORD
Presione para iniciar una grabación.
SP
–
–
36
1L25
51. Botón PAUSE
48. Botón
g
GModo DVD
GModo DVD
Presione para pausar la reproducción de Disco.
Pulse para avanzar rápidamente el disco. Pulse
PAUSE, luego pulse este botón para comenzar la
reproducción en movimiento lento. Pulse este botón
en forma repetida para cambiar la velocidad de
avance en movimiento lento.
Presione repetidamente para avanzar la imagen DVD
paso a paso (o un fotograma cada vez).
GModo VCR
Mientras graba, presione para detener provisional-
mente la grabación (pausa). Presione por segunda vez
para reanudar la grabación normal. Usted no puede
pausar Grabación de Un-Toque. O, presione durante
la reproducción de cinta para congelar la imagen.
52. Botón SLOW
GModo VCR
Pulse para avanzar rápidamente la cinta o para ver la
imagen rápidamente en avance durante la reproduc-
ción (Búsqueda en avance).
49. Botón PLAY
Durante la reproducción de cinta, presione mirar la cinta
de videó a movimiento lento. Presione de nuevo para
reanudar la reproducción normal. Este Botón no afecta
la reproducción DVD.
GModo DVD
Presiónelo para iniciar la reproducción.
GModo VCR
Presiónelo para iniciar la reproducción.
50. Botón VCR
53. Botón VCR/TV
Utilice para seleccionar la posición VCR o TV.
GPosición VCR
Presione antes de utilizar el control remote para fun-
ciones de VCR. Usted puede cambiar el modo de salida
ya presionando el Botón OUTPUT en el panel delantero
o ya presionando el Botón DVD o VCR en el control
remote. Sin embargo, si usted presiona el Botón OUT-
PUT en el panel delantero primero, usted necesita
volver a seleccionar el modo correspondiente presio-
nando el Botón DVD o el Botón VCR en el control
remote..
Para mirar la reproducción, para monitorear una
grabación de vídeo o para mirar TV utilizando el sin-
tonizador VCR.
GPosición de TV
Para mirar TV o para mirar un programa mientras se
graba otro.
54. Botones SKIP/CH
GModo DVD
Presione para saltar Capítulos o Pistas.
GModo VCR
Presione para cambiar canales de TV en la VCR.
55. Botón AUDIO
Presione para seleccionar un idioma de audio deseado o
modo de sonido.
VISIÓN TRASERA
56
57
58
59
60
DVD/VCR
VCR
DVD
AUDIO OUT
S-VIDEO COMPONENT AUDIO
DIGITAL
OUT
VIDEO OUT OUT
Y
AUDIO OUT
ANT-IN
L
AUDIO IN
VIDEO IN
R
Cb
Cr
L
COAXIAL
ANT-OUT VIDEO OUT
R
66
65
64
62
63
61
62. Tomas DVD AUDIO OUT
56. Toma ANTI-IN (Entrada de Antena)
Conecte su antena o cable aquí.
Conecte aquí los cables de audio provistos y a las tomas
de entrada de audio de un televisor u otro equipo de
audio (sólo DVD).
57. Tomas DVD/VCR AUDIO OUT
Conecte aquí los cables de audio provistos y a las tomas
de entrada de audio de un televisor u otro equipo de
audio.
63. Toma S-VIDEO OUT
Conecte aquí un cable de S-Videó opcional y a la toma
de entrada de S-Videó de un televisor.
58. Toma AUDIO IN
64. Toma VIDEO IN
Conecte aquí un cable de audio procedentes de la toma
de salida de audio de un camcorder, otra VCR o una
fuente de audio.
Conecte un cable procedente de la toma de salida de
videó de un camcorder, otra VCR o una fuente de audio-
visual (reproductor de disco láser, reproductor de disco
de videó, etc.) aquí.
59. Cordón de Alimentación AC
Conecte a una toma de corriente AC estándar para sum-
inistrar corriente al DVD/VCR.
65. Toma DVD/VCR VIDEO OUT
Conecte aquí el cable de videó amarillo (provisto) y a la
toma de entrada de Videó de TV.
60. Tomas COMPONENT VIDEO OUT
Conecte aquí los cables de videó componente
opcionales y a las tomas de entrada de Videó compo-
nente de un televisor.
66. Toma ANT-OUT (Salida de Antena)
Utilice el cable coaxial RF provisto para conectar esta
toma a la Toma ANTENNA IN en su TV.
Caja de cables o Sistema de Radiodifusión Directa.
61. Toma COAXIAL
Conecte aquí un cable de audio digital coaxial opcional
y a la toma de entrada Audio Digital Coaxial de un
descodificador o receptor de audio.
Notas
¡La toma S-VIDEO OUT, toma COAXIAL, y tomas COMPONENT VIDEO OUT son sólo útiles en el modo
DVD.
SP
–
–
37
1L25
CAMBIO DE VCR/DVD
Como este producto se utiliza del reproductor VCR y DVD, es necesario cambiar uno del
otro.
CAMBIO AL MODO VCR
CAMBIO AL MODO DVD
Presione el Botón VCR en el control remote.
(Verifique que la Luz VCR OUTPUT está enendida.)
Presione el Botón DVD en el control remote.
(Verifique que la Luz DVD OUTPUT está encendida)
Notas
¡Presionando sólo el Botón OUTPUT en el panel delantero no cambia el modo del control remote. Usted siem-
pre necesita seleccionar el modo correcto en el control remote, también.
POWER
OPEN/CLOSE
POWER SPEED AUDIO
CH-UP
STOP/EJECT
FF
OUTPUT
STOP
FWD
DVD
REW
REV
PLAY
VCR
REC
TIMER
REC
VIDEO
AUDIO
PLAY
DISC IN
CH-DOWN
PLAY
1
4
7
2
5
8
0
3
SKIP/CH.
6
VCR/TV
SLOW
9
Luz DVD OUTPUT
+
10
Botón DVD
Botón VCR
DISPLAY DVD
VCR
PAUSE
PLAY
STOP
OUTPUT
DVD
VCR
RECORD
MENU
Luz VCR OUTPUT
ENTER
SETUP
TITLE
RETURN
SEARCH
MODE
CLEAR/
MODE ZOOM
C.RESET
Botón OUTPUT
SUBTITLE ANGLE REPEAT
T-SET
A
B
SP
–
–
38
1L25
CONEXIONES
DVD/VCR A CONEXIÓN DE TV
CANAL DE SALIDA RF
1. Desconecte el cordón de alimentación AC del toma de Si su TV no tiene terminals A/V:
corriente AC.
1. Conecte el DVD/VCR a un TV utilizando un cable
RF (consulte CONEXIÓN DE UN DVD/VCR A
UN TV.)
2. Seleccione el canal 3 en su TV.
3. Presione PLAY.
GSi aparece ruido, cambie el canal de salida RF de
la VCR al canal 4 presionando PLAY durante 3
segundos durante la reproducción.
2. Desconecte la antena o cable del TV.
3. Conecte la antena o cable a la toma ANT.IN del
DVD/VCR.
4. Conecte el DVD/VCR al TV utilizando el cable coaxi-
al.
5. Enchufe los cordones de alimentación CA del
DVD/VCR y TV dentro de las tomas de corriente AC.
CONECTANDO A UN TV
Por favor, vea la [Fig.1] en la página 13 para detalles.
CONECTANDO A UN TV QUE TIENE TOMA DE ENTRADA DE S-
VÍDEO o TOMAS DE ENTRADA DE VÍDEO COMPONENTE
Por favor, vea la [Fig. 2] y [Fig. 3] en la página 14 para detalles.
CONECTANDO A UN AMPLIFICADOR EQUIPADO CON TOMAS DE
ENTRADA DIGITAL, TALES COMO PLATINA MD O PLATINA DAT
Por favor, vea la [Fig. 4] en la página 14 para detalles.
CONECTANDO A UN DESCODIFICADOR DIGITAL DOLBY
Por favor, vea la [Fig. 5] en la página 15 para detalles.
CONECTANDO A UN AUDIO ANALÓGICO
Por favor vea la [Fig. 6] en la página 15 para detalles.
PREPARACIÓN
PREPARACIÓN DE CANAL AUTOMÁTICA
VCR
4 Inicie canal preajustado presionando B una
vez. El sintonizador explora y memoriza todos
los canales activos de su área.
1
Seleccione el canal 3 en su TV.
Si aparece ruido, cambie el canal de salida
RF de la VCR al canal 4 presionando PLAY
durante 3 segundos durante la reproducción.
5
Después de explorar, el sintonizador de
detiene en el canal memorizado más bajo. La
pantalla de TV retorna al modo TV.
2
3
Conecte el DVD/VCR presionando POWER.
Ambas Luces POWER y VCR/TV se encen-
derán.
Seleccione el Idioma en la pantalla (“INGLÉS”,
“FRANCÉS” o “ESPAÑOL”) presionando
Luego, presione
K
o
L.
B.
SP
–
–
39
1L25
PREPARACIÓN DE RELOJ
REPRODUCCIÓN DE UN DISCO
VCR
REPRODUCIENDO UN DVD,
VIDEO O UN CD AUDIO
Ajuste el reloj con precisión para grabación con tempo-
rizador automática adecuada. Le sugerimos que usted utilice
un TV o estación de radio como su fuente de tiempos.
DVD
CD
1
Presione MENU dos veces para llamar el menú Para empezar
principal. (Si usted ha ajustado ya el reloj, usted Conecte la alimentación del TV, amplificador y
sólo tiene que presionarlo una vez).
cualquier otro componente que se encuentre conectado
al DVD/VCR. (Cambie el sistema de entrada para que
se adapte DVD/VCR y compruebe que el volumen de
sonido sea correcto).
¡
Si el reloj no está ajustado, aparece primero el menú
CLOCK SET. En este caso, siga el paso [3].
2
3
Seleccione “CLOCK SET” presionando
K
o
L.
1
Presione el Botón POWER.
Luego, presione
B
Compruebe que la Luz DVD OUTPUT está encen-
dida. Si no, presione el Botón DVD en el control
remote para cambiar el modo DVD/VCR.
Ajuste el reloj.
¡
Para retroceder un paso, presione
{
2
Presione el Botón OPEN/CLOSE.
1) Ajuste el mes
¡La bandeja de carga del disco se abrirá.
Presione o o p repetidamente
Luego, presione B.
3
Ponga un disco en la bandeja.
¡Asegúrese de que el disco está asentado correcta-
mente, con el lado de la etiqueta arriba.
2) Ajuste el día
Presione o o p repetidamente
Luego, presione B.
4
Presione el Botón PLAY.
¡La bandeja se cerrará automáticamente, y la repro-
ducción empezará luego desde el primer capítulo o
pista del disco. Usted necesita presionar el Botón
PLAY sólo cuando la bandeja se ha cerrado presion-
ando el Botón OPEN/CLOSE.
3) Ajuste el año
Presione o o p repetidamente
Luego, presione B.
El día de la semana aparecerá automáticamente.
4) Ajuste la hora
5
Presione el Botón STOP para detener la
reproducción.
Presione o o p repetidamente
Luego, presione B.
5) Ajuste el minuto
Presione o o p repetidamente
Luego, presione B.
6) Ajuste el AM o PM
AJUSTE DE RELOJ
MES DIA
AÑO
Presione o o prepetidamente.
03 17 LUN 2003
/
HORA MINUTO AM/PM
05 40 PM AM
PM
:
4
Ponga en marcha el reloj presionando
CLEAR/C.RESET o
B
.
SP
–
–
40
1L25
MEMO
EN
–
–
41
1L25
MEMO
EN
–
–
42
1L25
MEMO
EN
–
–
43
1L25
LIMITED WARRANTY
FUNAI CORP. will repair this Emerson product, free of charge in the USA in the event of defect in materials or
workmanship as follows:
DURATION:
PARTS:
FUNAI CORP. will provide parts to replace defective parts without charge for one (1) year from the
date of original retail purchase. Two (2) years for Picture Tube. Certain parts are excluded from this
warranty.
LABOR:
FUNAI CORP. will provide the labor without charge for a period of ninety (90) days from the date
of original retail purchase.
LIMITS AND EXCLUSIONS:
THIS WARRANTY IS EXTENDED ONLY TO THE ORIGINAL RETAIL PURCHASER. A PURCHASE
RECEIPT OR OTHER PROOF OF ORIGINAL RETAIL PURCHASE WILL BE REQUIRED TOGETHER WITH
THE PRODUCT TO OBTAIN SERVICE UNDER THIS WARRANTY.
This warranty shall not be extended to any other person or transferee.
This warranty is void and of no effect if any serial numbers on the product are altered, replaced, defaced, missing
or if service was attempted by an unauthorized service center. This FUNAI CORPORATION Limited warranty does
not apply to any product not purchased and used in the United States.
This warranty only covers failures due to defects in material or workmanship which occurs during normal use. It
does not cover damage which occurs in shipment, or failures which are caused by repairs, alterations or product not
supplied by FUNAI CORP., or damage which results from accident, misuse, abuse, mishandling, misapplication,
alteration, faulty installation, improper maintenance, commercial use such as hotel, rental or office use of this
product or damage which results from fire, flood, lightning or other acts of God.
THIS WARRANTY DOES NOT COVER PACKING MATERIALS, ANY ACCESSORIES (EXCEPT REMOTE
CONTROL), ANY COSMETIC PARTS, COMPLETE ASSEMBLY PARTS, DEMO OR FLOOR MODELS.
FUNAI CORP. AND ITS REPRESENTATIVES OR AGENTS SHALL IN NO EVENT BE LIABLE FOR ANY
GENERAL, INDIRECT OR CONSEQUENTIAL DAMAGES ARISING OUT OF OR OCCASIONED BY THE
USE OF OR THE INABILITY TO USE THIS PRODUCT. THIS WARRANTY IS MADE IN LIEU OF ALL
OTHER WARRANTIES, EXPRESS OR IMPLIED, AND OF ALL OTHER LIABILITIES ON THE PART OF
FUNAI, ALL OTHER WARRANTIES INCLUDING THE WARRANTY OF MERCHANTABILITY, AND
FITNESS FOR A PARTICULAR PURPOSE, ARE HEREBY DISCLAIMED BY FUNAI AND ITS
REPRESENTATIVES IN THE UNITED STATES.
ALL WARRANTY INSPECTIONS AND REPAIRS MUST BE PERFORMED BY A FUNAI AUTHORIZED
SERVICE CENTER. THIS WARRANTY IS VALID WHEN THE UNIT IS CARRIED-IN TO FUNAI
AUTHORIZED SERVICE FACILITY.
IMPORTANT:
THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, YOU MAY HAVE OTHER RIGHTS
THAT VARY FROM STATE TO STATE, IF, AT ANY TIME DURING THE WARRANTY PERIOD, YOU ARE
UNABLE TO OBTAIN SATISFACTION WITH THE REPAIR OF THIS PRODUCT, PLEASE CONTACT FUNAI
CORP.
ATTENTION:
FUNAI CORP. RESERVES THE RIGHT TO MODIFY ANY DESIGN OF THIS PRODUCT
WITHOUT PRIOR NOTICE.
To locate your nearest Emerson Authorized Service Center or for general service procedure, please
call 1-800-256-2487 or write to the following:
FUNAI CORPORATION, INC.
Customer Service
100 North Street; Teterboro, NJ 07608
Tel :1-800-256-2487
PLEASE DO NOT SHIP YOUR UNIT TO THE TETERBORO ADDRESS.
Printed in China
0VMN03468
#####
H9410UD
|