U S E R M A N U A L
Maritime Multi Computer Models
JH 10T08 MMC - 10,4 inch Maritime Multi Computer
JH 15T05 MMC - 15,0 inch Maritime Multi Computer
JH 19T02 MMC - 19,0 inch Maritime Multi Computer
JH 23T02 MMC - 23,1 inch Maritime Multi Computer
User Manual MMC (ETX)
Updated: 09 Mar 2007 Doc Id: INB100014-1 (Rev 19)
For models (including different options):
-A1, -A2, -C1, -C2
Slim
User Manual
Jakob Hatteland Display AS, Åmsosen, N-5578 Nedre Vats, Norway
Contents
Cables ..............................................................................................18
ꢀ
INB100014-1 (Rev 19)
IND100206-9
Contents of package
This product is shipped with:
Item
Description
Documentation/Drivers/Software CD(s) for factory installed
Illustration
components like mainboard, IDE, network etc.
1 pcs of Standard Power Cable.
(European Type F “Schuko” or US Type B standard plug)
Length 1.8m
Note: Power cable not included in the DC version.
1 pcs of User Manual (Slim version)
Note: The separate documentation for third party
components may be available on attached CD. The printed
manual only covers specific information for Hatteland
products, and not third party components.
1 pcs of configuration, test report and checklist sheets.
Optional accessories for Panel Computers:
Item
Description
Illustration
Bracket mounting kit: (Delivered only with optional bracket)
4 pcs of RenCol Tristar Knob Male - M6X10 mm
4 pcs of MicroPlastic - 6 mm Nylon washer.
4 pcs of Bolt with shoulder washer - M6X1X20
4 pcs of Flat washer
Suspension Bracket
5
INB100014-1 (Rev 19)
IND100207-1
ꢂ
INB100014-1 (Rev 19)
Jakob Hatteland Display AS
Introduction to Jakob Hatteland Display AS
Founded in 1987, Jakob Hatteland Display (JHD) offers the widest range of type approved marine monitors, panel
computers and type approved marine computers for the worldwide commercial, naval, yacht and cruise market.
Today the group develops and manufactures a complete range of IEC 60945 tested marine monitors, panel
computers and IEC 60945 tested marine computers.
“Design meets Functionality” - Series 2
ATTRACTION is more then just to show a nice picture on a screen. The new IEC60945 tested man-machine
interfaces, offered by Jakob Hatteland Display AS, will fulfill the customers wish for outstanding design combined
with the reliability of approved maritime Panel-Computers and Displays.
These IP rated products are meant to be usable in all maritime applications. By the proven optical bonding
technology, the Panel Computers and Displays show drastically reduced reflection and enhanced optical
performance. This truly allows inside or outside use of these products.
Cool is not only the design, but also the product by intelligent heat dissipation and reduced heating storage. Using
state-of-the-art components such as LCD-TFT Modules and ETX-PC bases industrial computers, long-term
availability and serviceability is secured.
Flexibility in application and service friendliness is achieved by a unique backpack solution, whereas the detachable
backpack contains the “intelligence” of the product.
The extreme small form factor used on this product line with a general depth of only 75mm (!) and for example for
the 19in with 416 (W) x 372 (H) mm, allows new-builds and retrofit installation almost everywhere.
The flush mounted glass front shows only what is necessary: the content of the picture. The frameless design can
smoothly be integrated into a console or it can be used as table mounted device (bracket version). A console version
are also available for installment on flybridges with IP66 rating.
This new HATTELAND® Series 2 Panel Computers MMC2 and Displays MMD2 will be available from Q2 2006
onwards in 12in., 15in. and 19in. sizes. The concept allows easy scaling in sizes from small LCD screens up to large
sizes of more than 32in LCD wide-screens. This outstanding and affordable product range offers a wide choice for
different needs.
Approved Marine Displays (MMD/STD) - Series 1
Hatteland Display’s marine monitors are based on high quality and state-of-the-art components with the highest
specifications, and meet all requirements for harsh maritime use. The displays are easily integrated into your system,
due to standardized products and features.
The MMD (Maritime Multi Display) series consists of sizes ranging from 10in to 23in.
Specifically designed for navigation and automation systems on ships, these certified LCD monitors comply to IP66
described in IEC 60925, are tested according to IEC 60945 and are approved by major classification societies such
as ABS, BV, ClassNK, DNV, GL and LR. Further to this marine standard, the 19in MMD, the 20in MMD and the 23in
MMD marine monitors are also available as ECDIS and ARPA radar-compliant units.
General
ꢃ
INB100014-1 (Rev 19)
IND100077-1
Jakob Hatteland Display AS
Approved Marine Panel Computers (MMC) - Series 1
The combination of the reliable design of the marine TFT-LCD modules, together with industrial computer boards,
allows Hatteland Display to offer a product range for customer applications where space is critical and full function
is desired in a single unit. In particular, the standardized ETX-board form factor allows full flexibility when it comes to
processor choice. Because of multiple useful standard components we can offer a highly attractive commercial
package
The MMC (Maritime Multi Computer) series consist of sizes ranging from 10in to 23in.
These products have also been designed for typical marine applications in navigation, automation and other
systems. Following Hatteland’s philosophy, these marine panel computers are fully tested according to IEC 60945
and are designed for type approval.
Approved stand-alone and rack-mounted marine computers
Two concepts are followed to offer variation in size, function and expansion slots for customers: approved black-box
computers for limited space and approved computers for standard 19in racks, which offer a high degree of
expansion. Configurations according to customer wishes are implicit, such as the operating system, CD-burner,
RAM, graphic card, HD, add-on cards, factory installed software and many, many more.
The approved computers are tested according to IEC 60945 and IACS E10 and meet the requirements for
IEC 61174 (ECDIS). Several approvals by major classification societies such as ABS, BV, ClassNK, DNV, GL and
LR are available or pending.
Flexible display solutions and night vision facilities
All JHD Type Approved displays, panel computers and marine computers provide maximum flexibility for customer
applications. JHD offers all products with AC or DC power supply, and marine displays and marine panel computers
have a fully linear dimmable function for night vision.
Upon customer request, specific color, mechanical and electrical function designs can be implemented. Many more
options are also available such as, sun visors, mounting brackets, different Windows or Linux operating systems
and touch screens. All products are designed and manufactured by JHD in Nedre Vats, Norway. The production and
configuration of all products takes place within Hatteland’s high capacity production plant#1 (opened in September
2003) in Nedre Vats, Norway.
Hatteland’s production facilities are designed for future expansion, which has enabled the creation of plant#2, our
Optical Technology facility, opened in October 2006. The chosen materials for the production of our products are
high grade industrial components able to fulfil form, fit and function requests.
About this manual
The manual contains electrical, mechanical and input/output signal specifications. All specifications in this manual,
due to manufacturing, new revisions and approvals, are subject to change without notice. However, the last update
and revision of this manual are shown both on the frontpage and also in the “Revision History” chapter. Please use
that as a reference.
Furthermore, for third party datasheet and user manuals, please see dedicated interactive CD (where included)
delivered with the product or contact our sales personnel for support. Please see the Contents Of Package chapter
in the beginning of this manual to determine if a dedicated manual CD are included.
General
9
INB100014-1 (Rev 19)
IND100077-1
UH R
it
ii
ft
tl
il
:
:
:
t
il l
105420
t f
tl
P
Si
Manufacturer & Country
Product & Serial Number
Product Information
Manufacture:
Jakob Hatteland Display
NORWAY
Product:
19 Inch
TFT
Product type:
JH 19T01MMD-A1-ꢃꢀ1
#
Serial Number
Description
115VAC/50-ꢂ0Hz
2ꢀ0VAC/50-ꢂ0Hz
100W
Power rating
Input Volt
Touchscreen products
Introduction to Jakob Hatteland Display products with touchscreen
We use both Resistive and Capacitive touchscreen solutions for our products. Please visit our
website to find your exact type number and then determine if it uses Resistive or Capacitive.
If you have a customized or tailored product, please check the specifications in this manual or
third-party specifications from your supplier.
Capacitive Touchscreen
Capacitive touchscreens operate using oscillator circuits that are located in each corner of the
glass overlay and measure the capacitance of the area to be “touched”. Depending on where the
user touches the overlay, the oscillators will vary in frequency. A touchscreen controller then
measures the frequency variations to ascertain the coordinates of the person’s touch. This glass
overlay has a coating that stores the charge deposited over its surface electrically. It will not
operate with either a gloved hand or with a mechanical stylus.
CAPACITIVE - Brief Specifications
Subject
Details
Construction
Top: ClearTek protective overcoat protects the sensors and increase durability.
Inside: Electrode X/Y grid pattern and conductive coating.
Bottom: Glass and conductive coating.
Small amount of voltage is applied to the four corners for measuring X and Y coordinates of the touch point.
Positional Accurancy
Touch Contact Requirements
Enduarance Tested
Cleaning
Reported touch coordinates are within 1.0% of true position. (Based on viewing area dimensions)
3 ms for finger input.
More than 225 million touches in one location without noticable degradation to the surface.
Water, isopropyl, alcohol, and similar non-abrasive cleaners.
Liquids on screen does not impede touchscreen performance.
Up to 88% at 550 nm; dependant on specific surface finish chosen.
Liquid Resistance
Light Transmission
Resistive Touchscreen
It generally uses a display overlay composed of layers, each with a conductive coating on the
interior surface. Special separator “dots” are distributed evenly across the active area and
separate the conductive interior layers. The pressure from using either a mechanical stylus or
finger produces an internal electrical contact at the “action point” which supplies the controller with
vertical and horizontal analog voltages for data input. The resistive touchscreens are anti-glare to
reduce reflective shine intensity, which will slightly diffuse the light output throughout the screen.
Resistive technology activation can be initiated by; a gloved hand, fingernail, mechanical stylus
or an ungloved finger.
RESISTIVE - Brief Specifications
Subject
Details
Construction
Top: Polyester with outside hard-surface coating with clear or anti-glare finish.
Inside: Transparent conductive coating.
Bottom: Glass substrate with uniform conductive coating.
Top and bottom layers separated by separator dots.
Positional Accurancy
Touch Activation Force
Standard deviation of error is less than +- 0.080-inch (2mm).
Typically 57 to 133 g
Expected Life Performance
More than 35 million touches in one location without failure, using a stylus similar to a finger.
Chemical Resistance
(Exposed for one hour)
Acetone, Ammonia-based glass cleaners, Common food and beverages,
Hexane, Isopropyl alcohol, Methylene chloride, Methyl ethyl ketone,
Mineral spirits, Turpentine
Light Transmission
Typically 75% over visible light spectrum.
Touchscreen
12
INB100014-1 (Rev 19)
IND100110-1
Touchscreen products
Location of Touchscreen label
Information about the factory mounted touchscreen and what driver to use, are indicated
on the dedicated label. The location is shown in this illustration together with label example.
(This label is attached on products produced after September 2006)
TOUCH SCREEN
This product is equipped with
a
Resistive Touch Screen:
Manufacturer
ouch Controller
Driver Download
:
:
:
ELO
T
ouchSystems
T
2210 Serial Controller P/N 055165-000
VSD100564-2210
Product Information
Manufacture:
Jakob Hatteland Display
NORWA
Product:
19 Inch
TFT
Product type:
JH 19T01MMD-A1-ꢃꢀ1
#
Y
Serial Number
115VAC/50-ꢂ0Hz
2ꢀ0VAC/50-ꢂ0Hz
100W
TOUCH SCREEN
This product is equipped with a Resistive Touch Screen:
Manufacturer
: ELO TouchSystems
Touch Controller
Driver Download
: 2210 Serial Controller P/N 055165-000
VSD100564-2210
Example label only
Up-2-date touchscreen drivers and documentation:
Please visit the 3rd party website as indicated on the label. You can also visit our website www.hatteland.com
to view the full list of our models with touchscreen. Before using the touchscreen, it should be calibrated for
your system. Please install the 3rd party software and use the Calibrate function from there.
Touchscreen
1ꢀ
INB100014-1 (Rev 19)
IND100110-3
1ꢁ
INB100014-1 (Rev 19)
General Installation Recommendations
Installation and mounting
1. Most of our products are intended for various methods of installation or mounting
(panel mounting, bracket mounting, ceiling/wall mounting etc.); for details, please see the relevant
mechanical drawings.
2. Adequate ventilation is a necessary prerequisite for the life of the product. The air inlet and outlet
openings must definitely be kept clear; coverings which restrict ventilation are not permissible.
3. Do not install the unit in a horizontal position (laying down), as this will cause heat to build up
inside the display which will damage the LCD Panel. To prevent this problem we recommend
installing the unit in a vertical position (±30 degrees) to improve the airflow through the unit.
4. Exposure to direct sunlight can cause a considerable increase in the temperature of the unit, and
might under certain circumstances lead to overtemperature. This point should already be taken
into consideration when the bridge equipment is being planned (sun shades, distance from the
windows, ventilation, etc.)
5. Space necessary for ventilation, for cable inlets, for the operating procedures and for
maintenance, must be provided.
6. To further improve the cooling of the unit we recommend installing Cooling Fans underneath
blowing upwards into the unit air inlet. This may be required in high temperature applications
and also when there is reason to expect temperature problems due to non-optimal way of
mounting(Ref.2-5).
7. If the push buttons of the product are not illuminated, an external, dimmable illumination
(IEC 60945, 6.5.c, e.g. Goose neck light is required for navigational use.
8. Information about necessary pull-relievers for cables is given in the installation drawings.
Attention must be paid to this information so that cable breaks will not occur, e.g. during service
work.
Brightness knob precaution
Please be aware of the risk of breaking or bending the brightness knob. The brightness knob
should be free of any obstruction.
Installation
1ꢂ
INB100014-1 (Rev 19)
IND100078-10
General Installation Recommendations
Ergonomics
1. Adjust the unit height so that the top of the screen is at or below eye level. Your eyes should
look slightly downwards when viewing the middle of the screen.
2. Adjust screen inclination to remain gaze angle to the centre of the screen approximately
perpendicular to the line of gaze.
3. When products are to be operated both from a sitting position and from a standing position, a
screen inclination of about 30° to 40° (from a vertical plane) has turned out to be favourable.
4. The brightness of displays is limited. Sunlight passing directly through the bridge windows - or its
reflection - which falls upon the screen workplaces must be reduced by suitable means
(negatively inclined window surfaces, Venetian blinds, distance from the windows, dark colouring
of the deckhead)
5. Units in the bridge wing area must be installed or mounted by suitable alignment or
bulkhead/ deckhead mounting in such a way that reflections of light from the front pane of the
display are not directed into the observer’s viewing direction.
6. The use of ordinary commercial filter plates or filter films is not permitted for items of equipment
that require approval (by optical effects, “aids” of that kind can suppress small radar targets, for
example).
General mounting instructions
- The useful life of the components of all Electronics Units generally decreases with increasing
ambient temperature; it is therefore advisable to install such units in air-conditioned rooms. If there
are no such facilities these rooms must at least be dry, adequately ventilated and kept at a suitable
temperature in order to prevent the formation of condensation inside the display unit.
- With most Electronic Units, cooling takes place via the surface of the casing. The cooling must not
be impaired by partial covering of the unit or by installation of the unit in a confined cabinet.
- In the area of the wheel house, the distance of each electronics unit from the magnetic standard
compass or the magnetic steering compass must not be less than the permitted magnetic
protection distance.
This distance is measured from the centre of the magnetic system of the compass to the nearest
point on the corresponding unit concerned.
- Units which are to be used on the bridge wing must be installed inside the “wing control console”
protected against the weather. In order to avoid misting of the viewing screen, a 25 ... 50 W
console-heating (power depending on the volume) is recommended.
- When selecting the site of a display unit, the maximum cable lengths have to be considered.
Installation
17
INB100014-1 (Rev 19)
IND100078-10
General Installation Recommendations
- The impairment of read-out from a display screen by direct light from lamps or the sun must be
avoided. Rear windows must be blacked out by means of roller blinds or Venetian blinds.
- Disturbing reflections on the screen of a display caused by pilot lamps and illuminated signs must
be prevented by suitable measures (screening or relocating).
- When a product is being installed, the surface base or bulkhead must be checked to ensure that it
is flat in order to avoid twisting of the unit when the fixing screws are tightened, because such
twisting would impair mechanical functions. Any unevenness should be compensated for by
means of spacing-washers.
- The grounding screws of the units must be connected to the body of the ship (ground); the wire
used should have a cross sectional area of at least 6 mm2.
- Transportation damage, even if apparently insignificant at first glance, must immediately be
examined and be reported to the freight carrier. The moment of setting-to-work of the equipment
is too late, not only for reporting the damage but also for the supply of replacements.
Cables
Use only high quality shielded signal cables. For RGB/DVI cables use only cables with separate
coax for Red, Green and Blue. Jakob Hatteland Display can supply a varity of high quality RGB/
DVI, RS232, PARALLEL, LAN and USB cables intended for this use.
Cable Entries & Connectors (Marked area) - Illustration only
Bottom View
Back View
Installation
1ꢃ
INB100014-1 (Rev 19)
IND100078-10
General Installation Recommendations
Maximum Cable Length
The RGB/DVI cable should generally be kept as short as possible to provide a high quality output
on the display. The maximum cable length will depend on the signal resolution and frequency, but
also on the quality of the signal output from the computer. We recommend using 60Hz vertical
frequency for our displays.
Cables up to 10 meters generally provides good picture quality even with a 1600x1200 (UXGA)
60Hz signal. In most cases (especially with lower resolutions) even longer cables will provide a
satisfactory result. This should however be tested in advance before making the decision on how
far the unit can be placed from the signal source.
Standard Bracket
When mounting the bracket on the MMC products, USE only the provided bracket kit. Using any
other or longer bolts may/or will do serious damage to components inside the product, and will
void warranty! Use a Allen Wrench tool to fasten the middle bolts.
Please see the Technical Drawings section in this manual for additional information.
Provided kit consists of:
4 pcs of RenCol Tristar Knob Male - M6x10 mm
4 pcs of MicroPlastic - 6mm Nylon washer.
4 pcs of Bolt with shoulder washer - M6x1x20mm
4 pcs of Flat washer
Mount the bracket with the center bolt and washers
on each side.
Mount the Tristar bolts on each side.
Adjust the tilting angle and secure all bolts.
Note: MMC brackets for other products vary in size.
Installation
19
INB100014-1 (Rev 19)
IND100078-10
20
INB100014-1 (Rev 19)
Physical Overview - MMC ETX
Front area of computer
Power Button
Reset Button
Power LED
Brightness
Harddrive LED
Front USB Connector
FRONT USBꢁ INPUT/OUTPUT:
Supports any USB 2.0 (480Mbps) compliant peripherals. Drivers for most USB devices are
useally included in operating system or on separate installation CD’s delivered with product.
USB 1.1 devices will operate in USB 1.1 mode (12 Mbps)
Harddrive LED (HDD LED):
(This HDD LED is not available on 10” and 23” models).
The harddrive indication (LED) will turn orange when there occur read / write activity to / from the
harddrive.
Power LED & Power Button:
To turn ON the computer, press down button and release it immediately. The power indication
(LED) will turn green and any operating system will automatically boot. If the computer is in
standby this LED will be red. To turn OFF the computer, press down this button and hold it for 3
seconds. The operating system may require additionally tasks to be performed before computer
shuts down and turns off the unit.
Brightness:
The product features a 100% dimmable image, which means it is capable of displaying a
completely black image when the brightness knob is turned fully to the left.
Note: If the display is delivered with Transflective Technology, the dimming may vary depending on environment.
Transflective Technology uses environment / ambient lighting to preserve / enhance the brightness, meaning such
products are very suitable for viewing in direct sunlight.
Reset Button: (Hard Reset)
To reset the computer in case of software failure, press this button (it is mounted inside, to access
it use a screwdriver or a pen), This reset button is a hard reset which means the operating system
will NOT be warned. Using this reset method may damage files and / or operating system in worst
case scenarios. Precaution should be taken when using this.To perform a safe software reset,
press either the power button, or use the operating system own reset functionality if possible.
22
INB100014-1 (Rev 19)
IND100133-10
Physical Overview - MMC ETX
Connector area of computer
Power Input
PCI SLOT 1
PCI SLOT 2
COM4, COM2
COM3, COM1
Parallel (LPT)
RGB OUT
PS/2 Mouse
Compact Flash Reader
Network GigaBitLAN & LAN
PS/2 Keyboard
USB 1,2,3
NOTE: Available connectors / locations (may) vary depending on model !
PCI Slots 1&2: (Not available on all models!)
Supports PCI (Short Length / Standard Profile) card in two available slots. These PCI cards are
normally installed from factory or returned to factory for upgrading if needed. Note that warranty
will be void if you install PCI cards yourselves. In order to mount PCI cards, the chassis of the unit
must be removed, thus making warranty void as the warranty sticker would have to be broken.
The PCI slots are not available on all MMC ETX models, due to space restrictions.
COM1,2,ꢀ,ꢁ Serial Ports INPUT/OUTPUT:
Supports RS232 / RS422 / RS485 using D-SUB 9P Male connectors. Fasten the cable to the
connector using the provided screws on the cable housing itself. (Factory default is RS232 only)
Network INPUT/OUTPUT:
Supports 10/100Mbps Ethernet (LAN) and 10/100/1000Mbps Ethernet (GBLAN). Suitable for
twisted pair cables CAT.5E. Make sure the network cable connector ”clicks” into the RJ-45
connector.
RGB OUTPUT:
Will output a clone signal from the computer for use with external display or monitor. Connects via
a High Density D-SUB 15P Female connector. Fasten the cable to the connector using the
provided screws on the cable housing itself.
LPT1 Parallel Port INPUT/OUTPUT:
Standard LPT1 Printer/Parallel (SPP/EPP/ECP) port using a D-SUB 25P Female connector.
Fasten the cable to the connector using the provided screws on the cable housing itself.
2ꢀ
INB100014-1 (Rev 19)
IND100133-10
Physical Overview - MMC ETX
PS/2 Keyboard and PS/2 Mouse INPUTS:
Connect the PS/2 keyboard cable to the PS/2 5P Connector (female) marked with KEYBOARD.
Connect the PS/2 mouse cable to the PS/2 5P Connector (female) marked with MOUSE.
CompactFlash Reader:
CompactFlash Reader supports Type I & II cards. Insert the card gently into the slot with the logo
facing towards the TFT display (only when the unit is off). The card is removed by pressing the
EJECT button next to the card slot. A wide range of card sizes are supported.
NOTE: DO NOT ATTEMPT TO REMOVE THE FLASH CARD WHILE THE UNIT IS OPERATING!
This is because the CF Slot has been configured to operate as a IDE device. If the Flash
Card is removed from the slot while the unit is on, data may be lost or partly corrupted.
USB1,2,ꢀ INPUT/OUTPUT:
Supports any USB1.1 (12Mbps) or USB2.0* (480Mbps) compliant peripherals. Drivers for most
USB devices are useally included in operating system or on separate installation CD’s delivered
with product. USB 1.1 devices will operate in USB 1.1 mode (12 Mbps)
*Note: USB2.0 may not be supported on all MMC ETX models. Please review the specifications.
Power INPUT: (AC or DC Model)
AC MODEL ONLY:
The internal AC power module supports both 115VAC/60Hz and 230/50Hz power
input using a standard IEC European power plug.
DC MODEL ONLY:
Secure the cables (check polarity!) to the screw terminal. The internal DC power
module supports 24 VDC.
2ꢁ
INB100014-1 (Rev 19)
IND100133-10
Specifications - JH 10T08 MMC
Note: All specifications are subject to change without prior notice!
M E C H A N I C A L D E S C R I P T I O N
Physical Dimensions:
T E C H N I C A L D E S C R I P T I O N
TFT Technology:
• 10.4 inch viewable image size
• Active Matrix, Thin Film Transistor (TFT)
• RGB vertical stripe
• 339 (W) x 256 (H) x 91 (D) mm
• Weight: 7 kg (approx)
User Controls:
TFT Characteristics:
On front bezel:
• Power On/Off (push button)
• Brightness Control
• Pixel number
• Pixel pitch (RGB) : 0.264 (H) x 0.264 (V) mm
• Response Time
• Contrast Ratio
• Light Intensity
• Viewable Angle
: 800 x 600
: 10 ms (typical), “black” to “white”
: 500:1 (typical)
: 400 cd/m2 (typical)
: 40 deg. (Up), 60 deg. (Down/Left/Right)
: (@ CR > 10)
• Power LED Reset button
Behind hatch:
• USB 2.0 connector
• Active Display Area : 211.2 (H) x 158.4 (V) mm
• Max Colors : 262,144 (6-bit max)
Environmental Considerations:
• Operating
: Temperature -15 deg. C to +55 deg. C
Humidity 30% to 90% (non condensing)
: Temperature -20 deg. C to +70 deg. C
Humidity 10% to 90% (non condensing)
: EN60529 (IP66) (Applies for flush mounting)
Computer Specifications:
• Storage
• Installed OS
• Processor
: None, please specify when ordering
: Intel® Pentium®M 1.1GHz, Low Voltage
• IP Rating
• Cache / PCI Clock : 1MB Level 2 Cache / 400 MHz BUS
Safety Considerations:
• System Chipset
• BIOS
: Intel® 82855GME
: Phoenix 2Mbit Flash, Supports ACPI
: 1 x PC/104 with ISA Support
: 1 x SODIMM with ECC, from 256MB->1GB
: Intel® 82855GME (Integrated/250MHz)
: 1 x IDE Ports, Ultra DMA33/66/100
: 1 x Automotive 30GB, 2.5" IDE, 4200 RPM
: 1 x CF Socket with Eject (Type I & II)
Even although the test conditions for bridge units provide for a maximum
operating temperature of 55°C, continuous operation of all electronic
components should, if possible, take place at ambient temperatures of only
25°C. This is a necessary prerequisite for long life and low service costs.
• PC/104 Slot
• Memory Slot
• Graphics Chip
• IDE Controller
• Storage
Input/Output Connectors:
Function
Ethernet Lan/GBLan 2 x RJ-45
PC/104 Slot
Keyboard
Mouse
Compact Flash
COM 1
COM 2
COM 3
COM 4
LPT1
Back side
Inside
Front
• Compact Flash
• Parallel Port (LPT) : 1 x EPP/ECP Port
• Primary Ethernet : 1 x 10/100 Mbps
• Secondary Ethernet : 1 x 10/100/1000 Mbps
1 x PC/104 Slot
1 x PS/2
1 x PS/2
• Serial Ports
• USB Ports
• Keyboard/Mouse
: 4 x RS232/RS422/RS485 (fully isolated)*
: 4 x USB (2.0 compliant, 480Mbps)
: 2 x PS/2
1 x CF Socket
1 x DB9M
1 x DB9M
1 x DB9M
1 x DB9M
1 x DB25F
3 x USB
• Supported TFT Res. : From 640 x 480 up to 2048 x 1536**
• RGB OUT Res : From 640 x 480 up to 1600 x 1200
* only in RS422/485 mode
** Optimal 1:1 resolution and recommended is 800 x 600 @ 60 Hz.
** If resolutions is set above 1:1, desktop scrolling mode will be used.
USB2.0
1 x USB
AC Power
DC Power
RGB Out
Line In/Out
Mic In
Std IEC inlet (Odd version models)
DC Screw terminal (Even version models)
1 x HD-15F
3.5mm mini jack (depends on model)
3.5mm mini jack (depends on model)
Power Specifications:
Power Supply Options:
• 115 & 230VAC - 50/60Hz
• 24 VDC
: Model JH 10T08 MMC A1
: Model JH 10T08 MMC A2
Available Mechanical Options:
Accessories:
Power Consumption:
• Operating
: 100W (max) (Configuration depending)
: 65W (typ) (Max backlight & high CPU load)
• JH 10TSV
: Sun visor *
• JH 10TBRMMC : Bracket *
• Touch Screen **
Available Technical Options:
*
Option: Standard or custom logo and color
Miscellaneous Options:
** Option: Factory mounted
• Audio AC97 Compliant : Line In/Out, Mic In, Speaker Out
• Processor
• Memory
: Up to 2.0 GHZ
: Up to 1GB
Compass Safe Distance: JH 10T08 MMC
Standard: 55cm
Steering: 40cm
A P P R O V A L S & C E R T I F I C A T E S
This product have been tested / type approved by the following classification societies: (1=AC Version, 2=DC Version)
th
th
EN60945 4 (IEC945 4 )
DNV - Det Norske Veritas (1,2)
BV - Bureau Veritas (1,2)
IACS E10
ABS - American Bureau of Shipping (1,2)
ClassNK - Nippon Kaiji Kyokai (1,2)
2ꢂ
INB100014-1 (Rev 19)
IND100129-70
Specifications - JH 15T05 MMC
Note: All specifications are subject to change without prior notice!
M E C H A N I C A L D E S C R I P T I O N
Physical Dimensions:
T E C H N I C A L D E S C R I P T I O N
TFT Technology:
• 15.0 inch viewable image size
• Color Active Matrix LCD Module
• a-Si Thin Film Transistor (TFT)
• 412 (W), 345 (H), 83.5 (D) mm
• Weight: 8 kg (approx)
User Controls:
TFT Characteristics:
On front bezel:
• Power On/Off (push button)
• Brightness Control
• Pixel number
• Pixel pitch (RGB) : 0.297 (H) x 0.297 (V) mm
• Response Time
• Contrast Ratio
• Light Intensity
• Viewable Angle
: 1024 x 768
: 25 ms (typical), “black” to “white”
: 400:1 (typ)
: 250 cd/m2 (typical)
: +/- 85 deg. (min) (Up/Down/Left/Right)
: (@ CR > 10)
• Power LED, HD Led and Reset button
Behind hatch:
• USB 2.0 connector(s)
• Active Display Area : 304.1 (H) x 228.1 (V) mm
• Max Colors : 16.7 millions
Environmental Considerations:
• Operating
: Temperature -15 deg. C to +55 deg. C
Humidity 30% to 90% (non condensing)
: Temperature -20 deg. C to +70 deg. C
Humidity 10% to 90% (non condensing)
: EN60529 (IP66) (Applies for flush mounting)
Computer Specifications:
• Storage
• Installed OS
• Processor
: None, please specify when ordering
: Intel® Pentium®M 1.1GHz, Low Voltage
• IP Rating
• Cache / PCI Clock : 1MB Level 2 Cache / 400 MHz BUS
• System Chipset
• BIOS
: Intel® 82855GME
: Phoenix 2Mbit Flash, Supports ACPI
: 1 x PC/104 with ISA Support
: 1 x SODIMM with ECC, from 256MB->1GB
: Intel® 82855GME (Integrated/250MHz)
: 1 x IDE Ports, Ultra DMA33/66/100
: 1 x Automotive 30GB, 2.5" IDE, 4200 RPM
: 1 x CF Socket with Eject (Type I & II)
Safety Considerations:
Even although the test conditions for bridge units provide for a maximum
operating temperature of 55°C, continuous operation of all electronic
components should, if possible, take place at ambient temperatures of only
25°C. This is a necessary prerequisite for long life and low service costs.
• PC/104 Slot
• Memory Slot
• Graphics Chip
• IDE Controller
• Storage
Input/Output Connectors:
Function
Back side
Inside
Front
• Compact Flash
Ethernet Lan/GBLan 2 x RJ-45
PC/104 Slot
• Parallel Port (LPT) : 1 x EPP/ECP Port
• Primary Ethernet : 1 x 10/100 Mbps
• Secondary Ethernet : 1 x 10/100/1000 Mbps
1 x PC/104 Slot
Keyboard
Mouse
Compact Flash
COM 1
COM 2
COM 3
COM 4
LPT1
USB2.0
1 x PS/2
1 x PS/2
• Serial Ports
• USB Ports
• Keyboard/Mouse
: 4 x RS232/RS422/RS485 (fully isolated)*
: 4 x USB (2.0 compliant, 480Mbps)
: 2 x PS/2
1 x CF Socket
1 x DB9M
1 x DB9M
1 x DB9M
1 x DB9M
1 x DB25F
3 x USB
• Supported TFT Res. : From 640 x 480 up to 2048 x 1536**
• RGB OUT Res : From 640 x 480 up to 1600 x 1200
* only in RS422/485 mode
** Optimal 1:1 resolution and recommended is 1024 x 768 @ 60 Hz.
** If resolutions is set above 1:1, desktop scrolling mode will be used.
1 x USB
AC Power
DC Power
RGB Out
TV Out
Line In/Out
Mic In
Std IEC inlet (Odd version models)
DC Screw terminal (Even version models)
1 x HD-15F
Composite RCA (depends on model)
3.5mm mini jack (depends on model)
3.5mm mini jack (depends on model)
Power Specifications:
Power Supply Options:
• 115 & 230VAC - 50 / 60Hz
• 24 VDC
: Model JH 15T05 MMC A1
: Model JH 15T05 MMC A2
Available Mechanical Options:
Accessories:
Power Consumption:
• Operating
: 100W (max) (Configuration depending)
: 65W (typ) (Max backlight & high CPU load)
• JH 15TSV
: Sun visor *
• JH 15TBRMMC : Bracket *
• Touch Screen **
Available Technical Options:
Miscellaneous Options:
• Audio AC97 Compliant : Line In/Out, Mic In, Speaker Out
*
Option: Standard or custom logo and color
** Option: Factory mounted
• TV-Out
• Processor
• Memory
: 1 x Composite (Depends on model)
: Up to 2.0 GHZ
: Up to 1GB
Compass Safe Distance: JH 15T05 MMC
Standard: 125cm
Steering: 80cm
A P P R O V A L S & C E R T I F I C A T E S
This product have been tested / type approved by the following classification societies: (1=AC Version, 2=DC Version)
th
th
EN60945 4 (IEC945 4 ) (1,2)
IACS E10 (1,2)
ClassNK - Nippon Kaiji Kyokai (1,2)
GL - Germanischer Lloyd (1,2)
DNV - Det Norske Veritas (1,2)
BV - Bureau Veritas (1,2)
ABS - American Bureau of Shipping (1,2)
LRS - Lloyd's Register of Shipping (1,2)
RS - Russian Maritime Register of Shipping (1,2)
27
INB100014-1 (Rev 19)
IND100129-42
Specifications - JH 19T02 MMC
Note: All specifications are subject to change without prior notice!
M E C H A N I C A L D E S C R I P T I O N
Physical Dimensions:
T E C H N I C A L D E S C R I P T I O N
TFT Technology:
• 19.0 inch viewable image size
• Active Matrix, Thin Film Transistor (TFT)
• MVA Premium™ Technology
• 483 (W), 444 (H), 100 (D) mm
• Weight: 11 kg (approx)
User Controls:
TFT Characteristics:
On front bezel:
• Power On/Off (push button)
• Brightness Control
• Pixel number
• Pixel pitch (RGB) : 0.294 (H) x 0.294 (V) mm
• Response Time
• Contrast Ratio
• Light Intensity
• Viewable Angle
: 1280 x 1024
: 15 ms (typical), “black” to “white”
: 700:1 (typ)
: 300 cd/m2 (typical)
: +/- 85 deg. (min) (Up/Down/Left/Right)
: (@ CR > 10)
• Power LED, HD Led and Reset button
Behind hatch:
• USB 2.0 connector
• Active Display Area : 376.32 (H) x 301.056 (V) mm
• Max Colors : 16.7 millions
Environmental Considerations:
• Operating
: Temperature -15 deg. C to +55 deg. C
Humidity 30% to 90% (non condensing)
: Temperature -20 deg. C to +70 deg. C
Humidity 10% to 90% (non condensing)
: EN60529 (IP66) (Applies for flush mounting)
Computer Specifications:
• Installed OS
• Processor
: None, please specify when ordering
: Intel® Pentium®M 1.1GHz, Low Voltage
• Storage
• Cache / PCI Clock : 1MB Level 2 Cache / 400 MHz BUS
• IP Rating
• System Chipset
• BIOS
: Intel® 82855GME
: Phoenix 2Mbit Flash, Supports ACPI
Safety Considerations:
Even although the test conditions for bridge units provide for a maximum
operating temperature of 55°C, continuous operation of all electronic
components should, if possible, take place at ambient temperatures of only
25°C. This is a necessary prerequisite for long life and low service costs.
• PCI Slot (Limited height) : 2 x Short Length, STD Profile, 32Bit PCI
• PC/104 Slot
• Memory Slot
• Graphics Chip
• IDE Controller
• Storage
: 1 x PC/104 with ISA Support
: 1 x SODIMM with ECC, from 256MB->1GB
: Intel® 82855GME (Integrated/250MHz)
: 1 x IDE Ports, Ultra DMA33/66/100
: 1 x Automotive 30GB, 2.5" IDE, 4200 RPM
: 1 x CF Socket with Eject (Type I & II)
Input/Output Connectors:
Function
Back side
Inside
Front
• Compact Flash
Ethernet Lan/GBLan 2 x RJ-45
PCI Slot (Limited height)
PC/104 Slot
Keyboard
Mouse
Compact Flash
COM 1
COM 2
COM 3
COM 4
LPT1
USB2.0
AC Power
DC Power
RGB Out
TV Out
Line In/Out
Mic In
• Parallel Port (LPT) : 1 x EPP/ECP Port
• Primary Ethernet : 1 x 10/100 Mbps
• Secondary Ethernet : 1 x 10/100/1000 Mbps
2 x Short/STD
1 x PC/104 Slot
1 x PS/2
• Serial Ports
• USB Ports
• Keyboard/Mouse
: 4 x RS232/RS422/RS485 (fully isolated)*
: 4 x USB (2.0 compliant, 480Mbps)
: 2 x PS/2
1 x PS/2
1 x CF Socket
1 x DB9M
1 x DB9M
1 x DB9M
1 x DB9M
1 x DB25F
3 x USB
• Supported TFT Res. : From 640 x 480 up to 2048 x 1536**
• RGB OUT Res : From 640 x 480 up to 1600 x 1200
* only in RS422/485 mode
** Optimal 1:1 resolution and recommended is 1280 x 1024 @ 60 Hz.
** If resolutions is set above 1:1, desktop scrolling mode will be used.
1 x USB
Std IEC inlet (Odd version models)
DC Screw terminal (Even version models)
1 x HD-15F
Composite RCA (depends on model)
3.5mm mini jack (depends on model)
3.5mm mini jack (depends on model)
3.5mm mini jack (depends on model)
Power Specifications:
Power Supply Options:
• 115 & 230VAC - 50 / 60Hz
• 24 VDC
: Model JH 19T02 MMC A1
: Model JH 19T02 MMC A2
Speaker Out
Power Consumption:
• Operating
: 100W (max) (Configuration depending)
: 75W (typ) (Max backlight & high CPU load)
Available Mechanical Options:
Accessories:
• JH 19TSV
• JH 19TBRMMC-B1 : Bracket*
• Touch Screen **
: Sun visor *
Available Technical Options:
Miscellaneous Options:
• Audio AC97 Compliant : Line In/Out, Mic In, Speaker Out
*
Option: Standard or custom logo and color
** Option: Factory mounted
Option: See separate datasheet for bracket drawings.
• TV-Out
• Processor
• Memory
: 1 x Composite (Depends on model)
: Up to 2.0 GHZ
: Up to 1GB
*
Compass Safe Distance: JH 19T02 MMC
Standard: 75cm
Steering: 55cm
A P P R O V A L S & C E R T I F I C A T E S
This product have been tested / type approved by the following classification societies: (1=AC Version, 2=DC Version)
th
th
EN60945 4 (IEC945 4 ) (1,2)
IACS E10 (1,2)
EN61174 (IEC1174) - Bundesamt für Seeschiffahrt und Hydrographie (BSH) (1)
GL - Germanischer Lloyd (1,2)
BV - Bureau Veritas (1,2)
ABS - American Bureau of Shipping (1,2)
DNV - Det Norske Veritas (1,2)
LRS - Lloyd's Register of Shipping (1,2)
RS - Russian Maritime Register of Shipping (1,2)
ClassNK - Nippon Kaiji Kyokai (1,2)
2ꢃ
INB100014-1 (Rev 19)
IND100129-43
Specifications - JH 23T02 MMC
Note: All specifications are subject to change without prior notice!
M E C H A N I C A L D E S C R I P T I O N
Physical Dimensions:
T E C H N I C A L D E S C R I P T I O N
TFT Technology:
• 23.1 inch viewable image size
• Thin Film Transistor (TFT), MVA Premium™ Technology
• 584 (W), 534 (H), 105 (D) mm
• Weight: 18 kg (approx)
TFT Characteristics:
User Controls:
• Pixel number
: 1600 x 1200
On front bezel:
• Power On/Off (push button)
• Brightness Control
• Pixel pitch (RGB) : 0.294 (H) x 0.294 (V) mm
• Response Time
• Contrast Ratio
• Light Intensity
• Viewable Angle
: 20 ms (typical), “black” to “white”
: 600:1 (typ)
: 250 cd/m2 (typical)
: +/- 85 deg. (min) (Up/Down/Left/Right)
: (@ CR > 10)
• Power LED and Reset button
Behind hatch:
• USB 2.0 connector
• Active Display Area : 470.4 (H) x 352.8 (V) mm
• Max Colors
: 16.7 millions (depending on graphics card)
Environmental Considerations:
Computer Specifications:
• Operating
: Temperature -15 deg. C to +55 deg. C
Humidity 30% to 90% (non condensing)
: Temperature -20 deg. C to +70 deg. C
Humidity 10% to 90% (non condensing)
: EN60529 (IP66) (Applies for flush mounting)
• Installed OS
• Processor
: None, please specify when ordering
: Intel® Pentium®M 1.1GHz, Low Voltage
• Storage
• Cache / PCI Clock : 1MB Level 2 Cache / 400 MHz BUS
• IP Rating
• System Chipset
• BIOS
: Intel® 82855GME
: Phoenix 2Mbit Flash, Supports ACPI
Safety Considerations:
Even although the test conditions for bridge units provide for a maximum
operating temperature of 55°C, continuous operation of all electronic
components should, if possible, take place at ambient temperatures of only
25°C. This is a necessary prerequisite for long life and low service costs.
• PCI Slot (Limited height) : 2 x Short Length, STD Profile, 32Bit PCI
• PC/104 Slot
• Memory Slot
• Graphics Chip
• IDE Controller
• Storage
: 1 x PC/104 with ISA Support
: 1 x SODIMM with ECC, from 256MB->1GB
: Intel® 82855GME (Integrated/250MHz)
: 1 x IDE Ports, Ultra DMA33/66/100
: 1 x Automotive 30GB, 2.5" IDE, 4200 RPM
: 1 x CF Socket with Eject (Type I & II)
Input/Output Connectors:
• Compact Flash
Function
Back side
Inside
Front
• Parallel Port (LPT) : 1 x EPP/ECP Port
• Primary Ethernet : 1 x 10/100 Mbps
• Secondary Ethernet : 1 x 10/100/1000 Mbps
Ethernet Lan/GBLan 2 x RJ-45
PCI Slot
2 x Short/STD
1 x PC/104 Slot
PC/104 Slot
Keyboard
Mouse
1 x PS/2
1 x PS/2
• Serial Ports
• USB Ports
• Keyboard/Mouse
: 4 x RS232/RS422/RS485 (fully isolated)*
: 4 x USB (2.0 compliant, 480Mbps)
: 2 x PS/2
Compact Flash
COM 1
COM 2
COM 3
COM 4
LPT1
USB2.0
1 x CF Socket
1 x DB9M
1 x DB9M
1 x DB9M
1 x DB9M
1 x DB25F
3 x USB
• Supported TFT Res. : From 640 x 480 up to 2048 x 1536**
• RGB OUT Res : From 640 x 480 up to 1600 x 1200
* only in RS422/485 mode
** Optimal 1:1 resolution and recommended is 1600 x 1200 @ 60 Hz.
** If resolutions is set above 1:1, desktop scrolling mode will be used.
1 x USB
AC Power
DC Power
RGB Out
TV Out
Line In/Out
Mic In
Std IEC inlet (Odd version models)
DC Screw terminal (Even version models)
1 x HD-15F
Composite RCA (depends on model)
3.5mm mini jack (depends on model)
3.5mm mini jack (depends on model)
Power Specifications:
Power Supply Options:
• 115 & 230VAC - 50 / 60Hz
• 24 VDC
: Model JH 23T02 MMC A1
: Model JH 23T02 MMC A2*
*(tests pending)
Power Consumption:
Available Mechanical Options:
Accessories:
• Operating
: 100W (max) (Configuration depending)
: 75W (typ) (Max backlight & high CPU load)
• JH 23TSV
: Sun visor *
Available Technical Options:
• JH 23TBRMMC-B1 : Bracket*
• Touch Screen **
Miscellaneous Options:
• Audio AC97 Compliant : Line In/Out, Mic In, Speaker Out
*
*
Option: Standard or custom logo and color
Option: See separate datasheet for bracket specifications.
• TV-Out
• Processor
• Memory
: 1 x Composite (Depends on model)
: Up to 2.0 GHZ
** Option: Factory mounted
: Up to 1GB
Compass Safe Distance: JH 23T02 MMC
Standard: 175cm
Steering: 140cm
A P P R O V A L S & C E R T I F I C A T E S
This product have been tested / type approved by the following classification societies: (1=AC Version, 2=DC Version)
th
th
)
EN60945 4 (IEC945 4
DNV - Det Norske Veritas (1)
BV - Bureau Veritas (1,2)
IACS E10
RS - Russian Maritime Register of Shipping (1,2)
ABS - American Bureau of Shipping (1,2)
ClassNK - Nippon Kaiji Kyokai (1,2)
29
INB100014-1 (Rev 19)
IND100129-47
ꢀ0
INB100014-1 (Rev 19)
ꢀꢃ
INB100014-1 (Rev 19)
Pin Assignments - Common Connectors
Note: Not all connectors may be available on your specific product. This depends on the amount of additional hardware installed from factory,
or customized solutions. These pin assignments are for the common connectors used. Connectors are seen from users Point Of View (POV).
Pin Assignments - USB TYPE A
Pin Assignments - RJꢁ5 10/100 LAN
1 2 ꢀ ꢁ 5 ꢂ 7 ꢃ
Pin 4: Ground
Pin 2: Negative Data
Pin 1: VCC +5V
Pin 3: Positive Data
Pin 01 - TDP
Transmit Differential Pair (Positive)
Pin 02 - TDN Transmit Differential Pair (Negative)
Pin 03 - RDP Receive Differential Pair (Positive)
Pin Assignments - USB TYPE B
Pin 1: VCC +5V
Pin 2: Negative Data
Pin 04 - NC
Pin 05 - NC
Not Connected
Not Connected
Pin 06 - RDN Receive Differential Pair (Negative)
Pin 07 - NC
Pin 08 - NC
Not Connected
Not Connected
Pin 3: Positive Data
Pin 4: Ground
Use category 5 - twisted pair cable
Pin Assignments - 5P PS/2 MOUSE
Pin Assignments - RJꢁ5 10/100/1000 GBLAN
1 2 ꢀ ꢁ 5 ꢂ 7 ꢃ
Pin 6: Not Connected
Pin 5: Mouse Clock
Pin 4: Vcc +5V
Pin 3: Ground
Pin 2: Not Connected
Pin 1: Mouse Data
Pin 01 - D0P
Pin 02 - D0N
Pin 03 - D1P
Pin 04 - D2P
Pin 05 - D2N
Pin 06 - D1N
Pin 07 - D3P
Differential Pair 0 (Positive)
Differential Pair 0 (Negative)
Differential Pair 1 (Positive)
Differential Pair 2 (Positive)
Differential Pair 2 (Negative)
Differential Pair 1 (Negative)
Differential Pair 3 (Positive)
Pin Ass. - 5P PS/2 KEYBOARD+MOUSE Combined
Pin 6: Mouse Clock
Pin 5: Keyboard Clock
Pin 4: Vcc +5V
Pin 3: Ground
Pin 2: Mouse Data
Pin 1: Keyboard Data
Pin Assignments - 15P HD RGB VGA
5
10
ꢁ
ꢀ
2
1
Pin Assignments - 5P PS/2 KEYBOARD
9
ꢃ
7
ꢂ
Pin 6: Not Connected
Pin 5: Keyboard Clock
Pin 4: Vcc +5V
Pin 3: Ground
Pin 2: Not Connected
Pin 1: Keyboard Data
15 1ꢁ 1ꢀ 12 11
Pin 01
Pin 02
Pin 03
Pin 04
Pin 05
Pin 06
Pin 07
Pin 08
Pin 09
Pin 10
Pin 11
Pin 12
Pin 13
Pin 14
Pin 15
Red, analog
Green, analog
Blue, analog
Reserved for monitor ID bit 2 (grounded)
Digital ground
Analog ground red
Analog ground green
Analog ground blue
+5V power supply for DDC (optional)
Digital ground
Reserved for monitor ID bit 0 (grounded)
DDC serial data
Pin Assignments - FIREWIRE IEEE-1ꢀ9ꢁ
1
ꢀ
5
2
ꢁ
ꢂ
Pin 01 - VCC Power
Pin 02 - GND Grounding for power and inner cable shield
Pin 03 - TPB- Twisted Pair B- Receive Strobe, Transmit Data
Pin 04 - TPB+ Twisted Pair B+ Receive Strobe, Transmit Data
Pin 05 - TPA- Twisted Pair A- Transmit Strobe, Receive Data
Pin 06 - TPA+ Twisted Pair A+ Transmit Strobe, Receive Data
Horizontal sync or composite sync, input
Vertical sync, input
DDC serial clock
Pin Assignments - 9P Serial COM RS2ꢀ2
5
ꢁ
ꢀ
2
1
9
ꢃ
7
ꢂ
Pin 01 - DCD Data Carry Detect
Pin 02 - SIN Serial In or Receive Data
Pin 03 - SOUT Serial Out or Transmit Data
Pin 04 - DTR Data Terminal Ready
Pin 05 - GND Ground
Pin 06 - DSR Data Set Ready
Pin 07 - RTS
Pin 08 - CTS
Pin 09 - RI
Request To Send
Clear To Send
Ring Indicate
Appendix
ꢁ2
INB100014-1 (Rev 19)
IND100241-2
Pin Assignments - Common Connectors
Pin Assignments - 25P Parallel
1ꢀ 12 11 10 9 ꢃ 7 ꢂ 5 ꢁ ꢀ 2 1
25 2ꢁ 2ꢀ 22 21 20 19 1ꢃ 17 1ꢂ 15 1ꢁ
Pin 01 - STROBE
Pin 02 - DATA0
Pin 03 - DATA1
Pin 04 - DATA2
Pin 05 - DATA3
Pin 06 - DATA4
Pin 07 - DATA5
Pin 08 - DATA6
Pin 09 - DATA7
Pin 10 - ACK
This signal indicates to the printer that data at PD7..0 are valid.
Parallel data bus from PC board to printer. The data line are able to operate in PS/2 compatible bi-directional mode.
Same as Pin 02
Same as Pin 02
Same as Pin 02
Same as Pin 02
Same as Pin 02
Same as Pin 02
Same as Pin 02
Signal from printer indicating that the printer has received the data and is ready to accept further data.
Signal from printer indicating that the printer cannot accept further data.
Signal from printer indicating that the printer is out of paper.
Pin 11 - BUSY
Pin 12 - PE
Pin 13 - SELECT
Pin 14 - AUTO FEED
Pin 15 - ERR#
Pin 16 - INIT#
Pin 17 - SLIN#
Pin 18 - GND
Pin 19 - GND
Pin 20 - GND
Pin 21 - GND
Pin 22 - GND
Pin 23 - GND
Pin 24 - GND
Pin 25 - GND
Signal from printer to indicate that the printer is selected.
This active low output causes the printer to add a line feed after each line printed.
Signal from printer indicating that an error has been detected.
This active low output initialises (resets) the printer.
Signal to select the printer sent from CPU board to printer.
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Pin Assignments - 2ꢁP DVI-D & DVI-I
1 2 ꢀ ꢁ 5 ꢂ 7 ꢃ C1 C2
9 10 11 12 1ꢀ 1ꢁ 15 1ꢂ
C5
17 1ꢃ 19 20 21 22 2ꢀ 2ꢁ Cꢀ Cꢁ
Pin 01
Pin 02
Pin 03
Pin 04
Pin 05
Pin 06
Pin 07
Pin 08
Pin 09
Pin 10
Pin 11
Pin 12
Pin 13
Pin 14
Pin 15
Pin 16
Pin 17
Pin 18
Pin 19
Pin 20
Pin 21
Pin 22
Pin 23
Pin 24
Pin C1
Pin C2
Pin C3
Pin C4
Pin C5
T.M.D.S. Data2 - (Digital - RED link 1)
T.M.D.S. Data2 + (Digital + RED link 1)
T.M.D.S. Data2/4 Shield
T.M.D.S. Data4 - (Digital - GREEN link 2)
T.M.D.S. Data4 + (Digital + GREEN link 2)
DDC Clock
DDC Data
Analog Vertical Sync (DVI-I only)
T.M.D.S. Data1 - (Digital - GREEN link 1)
T.M.D.S. Data1 + (Digital + GREEN link 1)
T.M.D.S. Data1/3 Shield
T.M.D.S. Data3 - (Digital - BLUE link 2)
T.M.D.S. Data3 + (Digital + BLUE link 2)
+5V Power (for standby mode)
Ground (for +5V and analog sync)
Hot Plug Detect
T.M.D.S. Data0 - (Digital - BLUE link 1) and digital sync.
T.M.D.S. Data0 + (Digital + BLUE link 1) and digital sync.
T.M.D.S. Data0/5 Shield
T.M.D.S. Data5 - (Digital - RED link 2)
T.M.D.S. Data5 + (Digital - RED link 2)
T.M.D.S. Clock Shield
T.M.D.S. Clock + (Digital clock + (Links 1 and 2)
T.M.D.S. Clock - (Digital clock - (Links 1 and 2)
Analog RED
Analog GREEN
Analog BLUE
Analog Horizontal Sync.
Analog Ground (return for RGB signals)
DDC = Display Data Channel /// T.M.D.S = Transition Minimized Differential Signal /// PIN C1,C2,C3,C4 = Only present on DVI-I connectors.
Additional connector pinouts may be available in third party motherboard manuals, primarly for
computers only. Please see manual/drivercd delivered with your product.
Appendix
ꢁꢀ
INB100014-1 (Rev 19)
IND100241-2
Pin Assignments - Common Connectors (Additional)
Note: These pin assignments applies for products with customer specified COM ports (factory setup).
These COM ports are configurable on the motherboard located inside the product.
Panel Computers: Attempting to config these yourselves, could result in warranty void as the main cover would have
to be removed.
Pin Assignments - 9P Serial COM RSꢁ22
ꢁ ꢀ 2 1
Pin Assignments - 9P Serial COM RSꢁꢃ5
ꢁ ꢀ 2 1
5
5
9 ꢃ 7 ꢂ
9 ꢃ 7 ꢂ
Pin 01 - N/C
Pin 02 - TX-
Pin 03 - RX+
Pin 04 - N/C
Not Connected
Transmit Data -
Receive Data +
Not Connected
Pin 01 - N/C
Pin 02 - N/C
Pin 03 - DAT+ Data+
Pin 04 - N/C
Pin 05 - GND Ground
Not Connected
Not Connected
Not Connected
Pin 05 - GND Ground
Pin 06 - N/C
Pin 07 - TX+
Pin 08 - RX-
Pin 09 - N/C
Not Connected
Pin 06 - N/C
Pin 07 - N/C
Pin 08 - DAT- Data-
Pin 09 - N/C Not Connected
Not Connected
Not Connected
Transmit Data +
Receive Data -
Not Connected
Appendix
ꢁꢁ
INB100014-1 (Rev 19)
IND100241-3
Basic Trouble-shooting
COMMON ERRORS: (This is a generic description of possible issues for a varity of products)
If for some reason there should be something wrong with the picture quality or no picture present, check the
symptoms carefully and try to cure it with the hints below:
NO PICTURE / LED BEHAVIOUR:
If there is no light at all in the LED at the FRONT, check power cables. If the LED in front is green then
check if the brightness knob is turned to the right (max brightness). If still no picture, check if there is a VGA
signal on the External VGA connector. If you have a picture on the external VGA connector please look in
BIOS documentation/chapter for correct display settings in BIOS. Lack of image is most likely to be caused
by incorrect connection, lack of power, or wrong BIOS settings.
SCROLLING / UNSTABLE IMAGE:
Signal cable may not be completely connected to computer or TFT display. Check the pin assignments and
signal timings of the display and your video card with respect to recommended timing and pin assignments.
Make sure that the video card is compatible and that it is properly seated / installed on the computer.
DISPLAY AREA IS NOT CENTERED / SIZED CORRECTLY
Make sure that a supported video mode has been selected on the display, or on the video card / system. If
it is impossible to position the image correctly, i.e. the image adjustment controls will not move the image
far enough, then test it again using another graphics card for the PC system. This situation may occur with
a custom graphics card that is not close to standard timings or if something is in the graphics line that may
be affecting the signal, such as a signal splitter (please note that normally a signal splitter will not have any
adverse effect). If it is impossible to change to the correct resolution/color depth, check if you have the right
VGA driver installed in your system.
IMAGE APPEARANCE:
A faulty TFT panel can have black lines, pixel errors, failed sections, flickering or flashing image.
Incorrect graphics card refresh rate, resolution or interlaced mode will probably cause the image to be the
wrong size, it may scroll, flicker badly or possibly even no image is present. Sparkling on the display may
be a faulty TFT panel signal cable, and it needs service attention.
RGB Signal Only:
Horizontal interference can usually be corrected by adjusting the PHASE (OSD menu).
Vertical interference can usually be corrected by adjusting the FREQUENCY (OSD menu).
DEW CONDENSATION BEHIND GLASS:
Note that this problem will not occur on bonded products. For non-bonded products, do the following:
Power on the TFT product and set brightness to 100%. Turn off any automatic screensavers on PC or
similar. During minutes the dew will be gone. To speed up the process, use a fan heater for a reasonable
time. Do not overheat the TFT product.
CD-ROM FAILURE OR READ/DETECTION PROBLEMS:
If the product are operated/located in a area with extreme condensation, the CD/DVD drive may not work
correctly due to condensation on the read head. Keep the product on for a while until it’s reached normal
operating temperature, and retry accessing discs. Otherwise, consider using USB memory sticks or
alternative storage devices.
NO CD-ROM AVAILABLE ON YOUR PRODUCT FOR INSTALLING DRIVERS/SOFTWARE:
Please use USB memory sticks, USB Floppy drive, USB CD-Rom Drive or alternative storage devices to
transfer/install software on CD-ROM-less units.
Appendix
ꢁ5
INB100014-1 (Rev 19)
IND100077-8
Declaration of Conformity
We, manufacturer
Jakob Hatteland Display A/S
Åmsosen, N-5578 Nedre Vats, Norway
declare under our sole responsibility that the
JH MMD, JH MMC, JH STD, JH MIL, HT STD (Series 1)
and HD MMD, HT MMC (Series 2) products is
in conformity with the following standards in
accordance with the EMC Directive.
EN 55022 Class A - Emission
EN 55024 - Immunity
Signature:........................................................
Frode Grindheim
Signature:........................................................
Arne Kristiansen
Technical Director
Jakob Hatteland Display A/S
Development Engineer
Jakob Hatteland Technology A/S
Date: 22 January 2007
Return Of Goods Information
Return of goods: (Applies not to warrenty/normal service/repair of products)
Before returning goods, please contact your system supplier before sending anything directly
to JHD. When you return products after loan, test, evaulation or products subject for credit,
you must ensure that all accessories received from our warehouse is returned to JHD.
This applies to cables, powermodules and additional equipment except screws or similar, user
manual, datasheets or other written paper documents. Furthermore, the product must not have any
minor / medium or severe scratches, chemical spills or similar on the backcover, front frame or
glass.
This is needed to credit the invoice 100%. Missing parts will not be subject for credit, and you will
not get total credit for returned product. You will either be charged separately or the amount is
withdrawn from the credit. If you decide to ship the missing items on the after hand, you will get
100% credit for that particular invoice or items received at JHD incoming goods control.
Please contact our service/sales department if additional questions.
Current prices apply as per May 200ꢁ:
Signal Cable DSUB 15P Male or Female - Approx 1,8meters
Signal Cable BNC 5P - Approx 1,8meters
Price: 170,- NOK each
Price: 350,- NOK each
RS-232 serial cable DSUB 9P - Approx 1,8meters
Price:
Price:
80,- NOK each
50,- NOK each
Powercable 110 / 220 VAC (European or US standard) - Approx 1,8meters
Minor / Medium or severe scratches / chemical spill on backcover
Any scratch, chemical spill or similar on front frame (including glass)
(Prices are approx, and any deviation are evaulated during incoming goods control)
Price: 1300,- NOK
Price: 2000,- NOK
Approved packaging methods/materials: (Applies to all shipments to JHD)
When returning goods, please make sure you surround the product with the following material,
whenever possible: Original packaging from JHD, firm foam material, bubble wrap or lots of
PadPack paper or Foam chips/polyester wrapped in sealed plastic bags. In any case, always use a
solid cardboard box to surround everything.
Not approved packaging methods/materials are: Foam chips, expanded polyester, clothes, nothing,
or too little, or anything that will crumble and get into the ventilation holes of products and
cardboard boxes that are not suitable to secure the product during shipment.
Appendix
ꢁ7
INB100014-1 (Rev 19)
IND100077-14
Terms
The Hatteland Group - Terms Of Sale And Delivery:
1) APPLICATION
The terms of sale and delivery include the following companies: Autostore AS, Jakob Hatteland Assembly AS,
Jakob Hatteland Computer AS, Jakob Hatteland Display AS, Jakob Hatteland Logistics, Jakob Hatteland Supply AS
and Jakob Hatteland Technology AS.
2) PRICE
a) The price is per each, if nothing else has been stated, VAT not included. Price is based on the prices from our
suppliers, current custom rates, taxes, rate of exchange and international raw material prices. We reserve ourselves
the rights to adjustments in case of alternation on the above mentioned.
b) Included in the price is the supplier’s standard packing. In case of re-packing/smaller quantities we reserve
ourselves the right to add an additional sum for warrantable packing according to CECC 0015 (Basic inspection for
protection of electrostatic sensitive devices)
ꢀ) VALIDITY
If nothing else has been stated in our quotation, the offer is valid for 30 days from the date of quotation.
ꢁ) PACKAGE QUOTATION
A package quotation means that all the components offered, must be ordered by us. If one component or more are
removed from the quotation, the prices given in the package quotation are not valid.
5) TERMS OF PAYMENT
Cash on delivery or payment in advance. Net granted for companies, schools and institutions only, according to
agreement. In case of too late payment 1.5% interest/month will be charged. Seller has mortage rights in the goods
delivered until the purchase price, additional interests and charges have been paid in full. Accepted bill is not
considered as payment until it has been honoured in full.
ꢂ) TIME OF DELIVERY
The quoted time of delivery is based on information from our suppliers. We disclaim any responsibility for the
consequences of any delay or cancellation from our suppliers. Belated delivery gives not solely the right for
cancellation.
7) DELIVERY POINT OF TIME
Goods are considered delivered to customer when handed over to charterer.
ꢃ) FREIGHT / PACKING / FORWARDING FEE
Jakob Hatteland Display AS charge NOK 50,- in forwarding fee for orders below NOK 1000,-.
For orders below NOK 1000,- Jakob Hatteland Supply AS charge freight according to expenses, and NOK 25,- for
packing. For handling requested beyond ordinary hours NOK 250,- is charged. Express service is charged with NOK
100,- + freight charges. All the companies charge freight according to expenses for orders above NOK 1000,-. VAT
not included.
9) COMPLAINT
By receipt customer must check goods for obvious defects which have to be claimed within 8 days from receipt.
Otherwise acceptance of complaint can not be counted on.
10) GUARANTEE / SERVICES
Time of guarantee is calculated from our date of shipment, and applies to the extent that we are covered by our
supplier’s guarantee regulations. The guarantee does no longer apply if:
I) there has been encroached upon the goods without seller’s consent
II) terms of payment is not fulfilled
III) the goods have been damaged due to unskilled treatment
IV) components which are sensitive for static electricity have not been unpacked and treated in a secure way.
Minimum requirements: CECC 00015’s standards for handling of such components. The guarantee does not include
fair wear and tear.
Appendix
ꢁꢃ
INB100014-1 (Rev 19)
IND100077-7
Terms
11) RESPONSIBLITY
Seller undertake to deliver faultless and functional capable goods according to existing technical specifications.
Seller disclaim responsibility for any damage or loss which directly or indirectly may be caused due to failure or defect
with the delivered goods, if carelessness from the seller can be limited up to the cost of the goods. The supplier’s
responsibility for defects with the supplied goods do not include secondary damage or loss.
12) CANCELLATION / RETURN
Binding sales contract is concluded when we have confirmed customer’s purchase order. Any disagreements in our
order confirmation must be reported to seller within 6 days. The agreement can not be altered without our permission,
after acceptance from our supplier. If goods are wanted to be returned, a Return No must be assigned from seller.
Returned goods without a Return No will not be accepted. By return of stock listed goods, 20% return fee is charged.
Returned goods are shipped on customer’s account and risk.
1ꢀ) LOAN, RENT and DEMO
When borrowing of goods for demo/test, the date of return must be added to the document. If no date has been
stated, date of return is two weeks from the date of the document. Before return, seller must be contacted for a
Return No (RTK). Goods which have been sold with an agreed right of return within stated terms, shall also have a
Return No. The Return No must be obtained before the stated date of return. Returned goods without a Return No, or
which have not been packed in original packing, will not be accepted.
1ꢁ) LIMITATIONS
If any of our suppliers claim limited delivery terms towards us, our terms of delivery will be restricted according to
those.
15) SOFTWARE
Sold or borrowed software is not allowed to be copied or spread in other ways, without a written permission.
1ꢂ) RE-EXPORT
Goods delivered from seller may be subject to special rules of exportation in their supplier’s native country. Buyer is
responsible to obtain necessary permissions for further export/re-sale.
17) QUESTION IN DISPUTE
To settle any dispute the Karmsund Herredsrett is approved the legal venue.
Appendix
ꢁ9
INB100014-1 (Rev 19)
IND100077-7
Terms
INSTRUCTIONS FOR THE CONSIGNEE
1) CONTROL
Control the goods immediately by receipt. Examine the quantity towards the invoice/packinglist/shipping documents.
Look for outward defects on the packing which may indicate damage on or loss of contents. Control the container and
the seals for any defects.
2) SECURING EVIDENCE
When defects on the goods have been found, evidence must be secured, and seller must be informed. Call the
transporter and point out the defects. Add a description of the defects on the goods receipt, the forwarder’s copy of
the way-bill or on the driving slip.
ꢀ) RESCUE
Bound the damage. Try to restrict the damage and the loss. Seller will compensate expences incurred due to
reasonable security efforts in addition to damage and loss.
ꢁ) COMPLAINT
Write immediately a complaint to the transporter or his agent. Forward immediately the complaint to the transporter or
his agent, and hold the transporter responsible for the defects. The complaint must be sent at the latest:
- for carriage by sea:
within 3 days
- for overland / air transportationwithin 7 days
5) DOCUMENTATION
For any claims the following documentation is required, and must be forwared to the company or their agent:
invoice, way-bill and/or bill of landing, and/or statement of arrival, inspection document, besides a copy of the letter of
complaint to the transporter.
Appendix
50
INB100014-1 (Rev 19)
IND100077-7
Notes
General Notes: (For all products)
- The unit is type approved according to EN60945 4 , 4.4, equipment category b) protected
from the weather.
th
- Other type approvals applies for the different products.
Please see Testing & Approvals Overview section in this manual for more information.
- Use of brightness and push buttons may inhibit visibility of information at night.
Note for ECDIS Systems
For ECDIS systems the brightness knob indication mark should be aligned directly with the
indication mark located on the label. (See Physical Overview or Operation section in this manual)
Note for Documentation CD-ROM
The separate and full documentation for third party components (including options that are factory
installed) are available on attached CD. The printed physical manual only covers specific
information for Hatteland products, and not generally includes third party components.
Appendix
51
INB100014-1 (Rev 19)
IND100077-20
Notes
Important BIOS Reset / No picture information
Please note that when performing a “Load Optimized Defaults”or “Load Fail-Safe
Defaults”command in the BIOS menu, or if the internal ETX processor module was replaced,
the picture on the TFT display will be black and the sync will be lost upon restart. No picture will be
present on the MMC unit!
However, by using the standard RGB OUT DSUB connector connected to an external TFT Display
or CRT Monitor, you will get a cloned picture from the MMC unit. Now you can correctly setup the
display properties in the BIOS, which will re-enable the picture to display correctly on the MMC unit
again. Please follow the procedure below for your MMC unit.
If you have no external display or monitor available, you can use the “blind man” routine:
1: Power on the MMC unit, while pressing <DEL> on the keyboard to enter BIOS setup.
2: Press the <DOWN ARROW> key 2 times, then press <ENTER>
3: Press the <DOWN ARROW> key 17 times, then press <ENTER>
4: Press the <DOWN ARROW> key 5 times (15 inch), 3 times (19/20 inch) or 6 times (23 inch)
followed by pressing <ENTER>
5: Press <F10> on the keyboard, and press <ENTER>. The BIOS settings will be saved, and the
unit will reset and boot up correctly with picture on the MMC Unit again.
BIOS Setup Menu Reference:
All versions of 15 Inch - JH 15T05MMC-xx (Pentium M)
- Choose “Advanced Chipset Features”
- Choose “Panel Number”
- Choose “1024x768 24bit SC”
All versions of 19 Inch - JH 19T02MMC-xx (Pentium M)
- Choose “Advanced Chipset Features”
- Choose “Panel Number”
- Choose “1280x1024 24bit SC”
All versions of 20 Inch - JH 20T05MMC-xx (Pentium M)
- Choose “Advanced Chipset Features”
- Choose “Panel Number”
- Choose “1280x1024 24bit SC”
All versions of 23 Inch - JH 23T02MMC-xx (Pentium M)
- Choose “Advanced Chipset Features”
- Choose “Panel Number”
- Choose “1600x1200 24bit SC”
When done, please refer to the BIOS manual if you need to change other options (available on
separate/attached CD for your specific product).
Appendix
52
INB100014-1 (Rev 19)
IND100077-31
Revision History
Rev. By
Date
SE 02 Sep 04 First release internet version. Products covered, JH 15T05 and JH 19T02
SE 26 Oct 04 Added pin assignments for RS422 and RS485
Notes
1
2
3
4
SE 08 Nov 04 Updated important security information regarding the Compact Flash Slot.
SE 04 Mar 05 Updated 19 Inch specification and Testing & Type Approval section.
Added JH 23T02 MMC.
Added Bracket Mounting Precautions and drawings.
5
6
SE
SE
17 Mar 05 Updated Testing and Type Approval Section.
21 Jun 05 Updated specifications.
7
SE 17 Aug 05 Updated Physical Connections Section.
8
SE 24 Aug 05 Added technical drawings for JH 19T02 MMC with bracket.
9
SE
7 Sep 05 Updated specifications.
10
11/12
13
SE 18 Nov 05 Updated specifications.
SE 22 May 06 Updated frontpage/design, updated Testing and Type Approvals section.
SE 22 Aug 06 Type approval page removed, and information merged with the respective
product specification pages.
14
15
16
SE 15 Sep 06 Updated specifications. Changed 5400 rpm to 4200 rpm
SE
SE
02 Oct 06 Added JH 10T08 MMC
02 Jan 07 Updated testing and type approvals for various products.
Updated specifications for all MMC products.
Available processor range now up to 2.0 GHZ.
17
SE
SE
22 Jan 07 Updated information regarding the HDD LED in user controls & specifications.
Applicable for 10” and 23” models.
18
19
01 Feb 07 Updated testing and type approvals.
SE 09 Mar 07 Updated specifications regarding resolutions.
Appendix
5ꢀ
INB100014-1 (Rev 19)
IND100077-25
Contact Information
Head office, Vats / Norway:
Jakob Hatteland Display AS
Åmsosen
N-5578 Nedre Vats, Norway
Tel: +47 5276 3700
Fax: +47 5276 5444
Sales office, Oslo / Norway:
Jakob Hatteland Display AS
Gjerdrums vei 12
N-0484 Oslo, Norway
Tel: +47 5276 3700
Fax: +47 2258 6790
Sales office, Tønsberg / Norway:
Jakob Hatteland Display AS
Narverødveien 40
N-3313 Tønsberg, Norway
Tel: +47 5276 3700
Fax: +47 3335 7049
Sales office, Frankfurt / Germany:
Jakob Hatteland Display GmbH
Werner Heisenberg Strasse 12,
D-63263 Neu-Isenburg, Germany
Tel: +49 6102 370 954
Fax: +49 6102 370 968
Sales office, Aix-en-Provence / France:
Jakob Hatteland Display SAS
Espace Cézanne - 14 Parc du Golf
350, Avenue JRGG de la Lauzière - CS 90519
13593 Aix-en-Provence Cedex 3, France
Tel: +33 (0)4 42 16 35 15
Fax: +33 (0)4 42 16 35 09
Sales office, Orlando / USA:
Jakob Hatteland Display Inc.
801 International Parkway, 5th Floor
Lake Mary, FL 32746, USA
Tel: +1 407 562 1677
Fax: +1 407 562 1777
|
