Electrolux EHG 9832 User Manual

instruction booklet  
GB  
gas hob  
EHG 9832  
electrolux 3  
Welcome to the world of Electrolux  
Thank you for choosing a first class product from Electrolux, which  
hopefully will provide you with lots of pleasure in the future.  
The Electrolux ambition is to offer a wide variety of quality products that  
make your life more comfortable.  
You find some examples on the cover in this manual. Please take a few  
minutes to study this manual so that you can take advantage of the benefits  
of your new machine.  
We promise that it will provide a superior User Experience delivering  
Ease-of-Mind.  
Good luck!  
4 electrolux  
Contents  
Instructions for the User  
Important safety information .................................................................5  
Description of the hob ...........................................................................8  
Operation ............................................................................................10  
Maintenance and Cleaning .................................................................12  
Something not working?......................................................................14  
Standard guarantee conditions...........................................................31  
European guarantee ...........................................................................33  
Instructions for the Installer  
Engineer technical data.......................................................................15  
Important safety requirements............................................................ 17  
Installation............................................................................................18  
Gas connection .................................................................................. 19  
Cut out size .........................................................................................20  
Building In............................................................................................21  
Fitting the hob into the worktop ...........................................................22  
Building over a cupboard or drawer ..................................................17  
Building over a kitchen unit with door .................................................18  
Electrical connections .........................................................................23  
Wiring diagram ...................................................................................25  
Fault finding .........................................................................................26  
Commissioning................................................................................... 29  
Conversion from natural gas to LPG ...................................................30  
Guide to Use the instructions  
The following symbols will be found in the text to guide you throughout the  
Instructions:  
Safety Instructions  
Step by step instructions for an operation  
!
Hints and Tips  
Environmental information  
"
electrolux 5  
Important safety information  
You MUST read these warnings carefully before installing or  
using the hob. If you need assistance, contact our Customer  
Care Department on 08705 950950.  
Installation  
#
This appliance must be installed and serviced by a competent person as  
stated in the Gas Safety (Installation and Use) Regulations Current Editions  
and the IEE Wiring Regulations.  
#
For appliances installed in the Republic of Ireland please refer to NSAI-  
Domestic Gas Installations I.S.813 Current Editions and the ETCI Rules for  
Electrical Installations.  
#
#
Remove all packaging before using the hob.  
Ensure that the gas and electrical supply complies with the type stated on  
the rating plate, located near the gas supply pipe.  
#
Do not attempt to modify the hob in any way.  
Child Safety  
#
This hob is designed to be operated by adults. Do not allow children to play  
near or with the hob.  
#
This appliance is not intended for use by children or other persons whose  
physical, sensory or mental capabilities or lack of experience and knowledge  
prevents them from using the appliance safely without supervision or instruction  
by a responsible person to ensure that they can use the appliance safely.  
#
#
The hob gets hot when it is in use. Children should be kept away until it has  
cooled.  
Children can also injure themselves by pulling pans or pots off the hob.  
During Use  
#
This hob is intended for domestic cooking only. It is not designed for  
commercial or industrial purposes.  
#
This appliance is not connected to a combustion products evacuation device.  
It must be installed and connected in accordance with current installation  
regulations. Particular attention shall be given to the relevant requirements  
regarding ventilation.  
#
#
When in use a gas cooking hob will produce heat and moisture in the room  
in which it has been installed. Ensure there is a continuous air supply, keeping  
air vents in good condition or installing a cooker hood with a venting hose.  
Ensure a good ventilation around the appliance. A poor air supply could cause  
lack of oxygen.  
6 electrolux  
#
When using the hob for a long period time, the ventilation should be  
improved, by opening a window or increasing the extractor speed.  
#
Do not use this hob if it is in contact with water. Do not operate the hob with  
wet hands.  
#
#
Ensure the control knobs are in the ‘OFF’ position when not in use.  
When using other electrical appliances, ensure the cable does not come  
into contact with the hot surfaces of the cooking appliance.  
#
Unstable or misshapen pans should not be used on the hob as unstable  
pans can cause an accident by tipping or spillage.  
#
#
#
Never leave the hob unattended when cooking with oil and fats.  
Never use plastic or aluminium foil dishes on the hob.  
Perishable food, plastic items and areosols may be affected by heat and  
should not be stored above or below the hob unit.  
#
This appliance cannot be cleaned with steam or with a steam cleaning  
machine.  
Service  
#
This hob should only be repaired or serviced by an authorised Service  
Engineer and only genuine approved spare parts should be used.  
electrolux 7  
Environmental Information  
After installation, please dispose of the packaging with due regard to  
safety and the environment.  
"
#
#
When disposing of an old appliance, make it unusable, by cutting off the  
cable.  
#
The symbol  
on the product or on its packaging indicates that this product  
may not be treated as household waste. Instead it shall be handed over to  
the applicable collection point for the recycling of electrical and electronic  
equipment. By ensuring this product is disposed of correctly, you will help  
prevent potential negative consequences for the environment and human  
health, which could otherwise be caused by inappropriate waste handling  
of this product. For more detailed information about recycling of this product,  
please contact your local city office, your household waste disposal service  
or the shop where you purchased the product.  
These instructions are only valid for countries whose identification symbols  
are shown on the cover of this instruction booklet and on the appliance itself.  
Keep this instruction book for future reference and ensure it is  
passed on to any new owner.  
This appliance is manufactured according to the following EEC  
directives:  
2006/95 EEC - 93/68 EEC - 89/336 EEC - 90/396 EEC, current  
edition.  
8 electrolux  
Description of the hob  
3
4
2
1
4
5
3
6
7
8
9
10  
11  
1. Hob Top  
2. Rapid Burner  
3. Auxiliary Burner  
4. Semi-rapid Burner  
5. Triple Crown Burner  
6. Control knob for front left burner (rapid)  
7. Control knob for back left burner (auxiliary)  
8. Control knob for central left burner (semi-rapid)  
9. Control knob for central right burner (semi-rapid)  
10. Control knob for back right burner (auxiliary)  
11. Control knob for front right burner (triple crown)  
electrolux 9  
INSTALLATION  
Any gas installation must be carried out by a registered  
competent person, and in accordance with existing rules  
and regulations.  
The relevant instructions are to be found in the second section of this  
manual.  
Please, ensure that, once the hob is installed, it is easily accessible for  
the engineer in the event of a breakdown.  
WHEN THE HOB IS FIRST INSTALLED  
Once the hob has been installed, it is important to remove any protective  
materials, which were put on in the factory.  
The manufacturer will not accept liability, should the above instructions or  
any of the other safety instructions incorporated in this book be ignored.  
10 electrolux  
Operation  
Hob burners control knobs  
The symbols on the knobs mean that :  
#
there is no gas supply  
there is maximum gas supply  
there is minimum gas supply  
Lighting the burners  
For easier lighting, proceed before  
putting a pan on the pan support.  
To light a burner:  
push in the relevant control knob and turn  
!
#
itanticlockwisetomaximumposition(  
to ignite the burner.  
),  
#
After lighting the flame, keep the knob  
pushed down for about 5 seconds. This  
will allow the "thermocouple" (Fig. 1 - lett.  
D) to be heated and the safety device to be  
switched off, otherwise the gas supply  
would be interrupted.  
Triple crown burner  
#
Then adjust the flame as required.  
A
If the burner does not ignite, turn the control  
knob to zero, and try again.  
B
When switching on the mains, after  
installation or a power cut, it is quite normal  
for the spark generator to be activated  
automatically.  
D
In the absence of electricity, ignition can  
occur without the electrical device; in this  
case, approach the burner with a flame,  
push the relevant knob down and turn it  
anti-clockwise until it reaches the  
“maximum” position.  
C
A - Burner cap  
Fig. 1  
B - Burner crown  
C - Ignition electrode  
D- Thermocouple  
A
Cappellotto  
electrolux 11  
If the control knobs become difficult to turn, please contact your  
local Service Force Centre.  
Using the hob correctly  
To ensure maximum burner efficiency, it is strongly recommended that  
you use only pots and pans with a flat bottom fitting the size of the burner  
used, so that flame will not spread beyond the bottom of the vessel (see the  
table below).  
Burner  
minimum  
diameter  
maximum  
diameter  
Triple crown  
Large (rapid)  
Medium (semi-rapid) 120 mm  
Small (auxiliary) 80 mm  
180 mm  
160 mm  
260 mm  
260 mm  
220 mm  
180 mm  
As soon as a liquid starts boiling, turn down the flame so that it will  
barely keep the liquid simmering.  
Use only pans or pots with flat bottom.  
If you use a saucepan which is smaller than the  
recommended size, the flame will spread beyond the  
bottom of the vessel, causing the handle to overheat.  
Carefully supervise cooking with fat or oil, since these types of  
foodstuff can result in a fire, if over-heated.  
The stainless steel can become tarnished if excessively  
heated. Therefore prolonged cooking with potstones,  
earthenware pans or cast-iron plates is inadvisable. Also,  
do not use aluminium foil to protect the top during use.  
Make sure pots do not protrude over the edges of the  
cooktop and that they are centrally positioned on the rings  
in order to obtain lower gas consumption.  
Do not place unstable or deformed pots on the rings: they  
could tip over or spill their contents, causing accidents.  
Pots must not enter the control zone.  
12 electrolux  
Maintenance and Cleaning  
Before any maintenance or cleaning can be carried out,  
you must DISCONNECT the hob from the electricity supply.  
The hob is best cleaned whilst it is still warm, as spillage  
can be removed more easily than if it is left to cool.  
This appliance cannot be cleaned with steam or with a  
steam cleaning machine.  
The Hob Top  
Regularly wipe over the hob top using a soft cloth well wrung out in warm water  
to which a little wasing up liquid has been added. Avoid the use of the following:  
- household detergent and bleaches;  
- impregnated pads unsuitable for non-stick  
saucepans;  
- steel wool pads;  
- bath/sink stain removers.  
YES  
Should the hob top become heavily soiled, the  
following products are recommended:  
- For stainless steel hobs use a proprietary stainless  
steel cleaner.  
- For other hobs use Hob Brite or Bar Keepers  
Friend.  
Do not leave acid or alkaline  
substances (e.g. vinegar, salt,  
lemon juice, etc.) on the cooktop.  
Pan Supports  
NO  
Wash the pan supports using hot soapy water.  
Ifnecessary, a paste cleaner or a soap  
impregnated steelwool pad can be used with  
caution.After cleaning, be sure to wipe dry with a  
soft cloth.  
Take care when drying them as the enamelling  
process occasionally leaves rough edges. If  
necessay, remove stubborn stains using a paste  
cleaner. After cleaning, make sure that the pan  
supports are correctly positioned.  
electrolux 13  
To make burners work properly, ensure that pan supports are placed in a  
way that the arms are centred upon the burner as shown in the picture.  
Pay attention when replacing the pan supports in order to  
avoid damaging the hob top.  
The Burners  
The burner caps and crowns can be removed for cleaning.  
Wash the burners caps and crowns using hot soapy water, and remove  
marks with a mild paste cleaner. A well moistened soap impregnated  
steel wool pad can be used with caution, if the marks are particularly  
difficult to remove.  
After cleaning, be sure to wipe dry with a soft cloth.  
The Ignition electrode  
The electric ignition is obtained through a ceramic electrode which  
contains a metal electrode (Fig. 1 - C). Keep these components very  
clean, to avoid difficult lighting, and check that the burner crown holes  
(Fig. 1 - B) are not obstructed.  
14 electrolux  
Something not working?  
If the hob is not working correctly, please carry out the following checks  
before contacting your local Service Force Centre.  
SYMPTOM  
SOLUTION  
%
There is no spark when  
lighting the gas.  
&
Check that the unit is plugged  
in and the electrical supply is  
switched on.  
&
&
&
Check that the RCCB has not  
tripped (if fitted).  
Check the mains fuse has not  
blown.  
Check the burner cap and  
crown have been replaced  
correctly, e.g. after cleaning.  
%
The gas ring burns unevenly.  
&
&
Check the main jet is not  
blocked and the burner crown  
is clear of food particles.  
Check the burner cap and  
crown have been replaced  
correctly, e.g. after cleaning.  
If after all these checks, your hob still does not operate correctly, contact  
your local Service Force Centre.  
Please note that it will be necessary to provide proof of purchase for any  
in-guarantee service calls.  
In-guarantee customers should ensure that the above checks have been  
made as the engineer will make a charge if the fault is not a mechanical or  
electrical breakdown.  
electrolux 15  
Instructions for the Installer  
Engineer technical data  
OVERALL DIMENSIONS  
Width:  
Depth:  
894 mm  
510 mm  
CUT OUT DIMENSIONS  
Width:  
Depth:  
830 mm  
480 mm  
SUPPLY CONNECTIONS  
Gas:  
R 1/2 inch (1/2 inch male) Rear right hand corner  
Electric:  
230 V~ 50 Hz supply, 3 core flexible cable with  
non rewireable plug fitted with a 3 amp cartridge fuse  
HEAT INPUT  
Rear Left Burner  
(auxiliary)  
1.0 kW (3413 BTU/HR)  
Rear Right Burner  
(auxiliary)  
1.0 kW (3413 BTU/HR)  
2.0 kW (6826 BTU/HR)  
2.0 kW (6826 BTU/HR)  
Central Right Burner  
(semi rapid)  
Central Left Burner  
(semi rapid)  
Front Left Burner  
(rapid)  
3.0 kW Natural Gas (10239 BTU/HR)  
2.8 kW LPG (9556 BTU/HR)  
Front Right Burner  
(triple crown)  
4.0 kW (13652 BTU/HR)  
APPLIANCE CLASS  
APPLIANCE CATEGORY  
GAS SUPPLY  
3
II2H3+  
Natural gas G20 (2H) / 20 mbar  
16 electrolux  
BURNER  
POSITION  
RAPID  
SEMI-RAPID A U X I L I A R Y TRIPLECROWN  
TYPE OF GAS  
MAX MIN MAX MIN MAX MIN  
MAX  
MIN  
NOMINALTHERMAL  
POWER  
kW  
3.0  
0.75  
2.0  
0.45  
1.0  
0.33  
4.0  
1.2  
NATURAL GAS  
20 mbar  
NOMINALFLOW  
RATE  
m3/h 0.286 0.057 0.190 0.038 0.095 0.028  
119 Adjust. 96 Adjust. 70 Adjust.  
0.381  
146  
0.114  
VALUE =  
37.78 MJ/m3  
Ws - 50.7 MJ/ m3  
NOZZLEREFERENCE  
1/100mm  
Adjust.  
NOMINALTHERMAL  
POWER  
LPG GAS  
28-30/37 mbar  
VALUE =  
kW  
2.8  
0.75  
2.0  
0.45  
1.0  
0.33  
4.0  
1.2  
NOMINALFLOW  
RATE  
g/h  
202 43.5  
86 42  
144  
71  
29  
32  
72  
50  
21,5  
28  
288  
98  
86  
56  
49.92 MJ/Kg  
NOZZLEREFERENCE  
1/100mm  
electrolux 17  
Important safety requirements  
This hob must be installed in accordance with the Gas Safety (Installation and Use)  
Regulations (Current Edition) and the IEE Wiring Regulations (Current Edition).  
For appliances installed in the Republic of Ireland please refer to NSAI- Domestic  
Gas Installation I.S. 813 Current Editions and the ETCI Rules for Electrical  
Installations.  
Provision for Ventilation  
Detailed recommendations are contained in the following British Standards Codes  
Of Practice: B.S. 6172/ B.S. 5440, Par. 2 and B.S. 6891 Current Editions.  
The hob should not be installed in a bed sitting room with a volume of less than 20  
m3. If it is installed in a room of volume less than 5 m3 an air vent of effective area of  
110 cm2 is required. If it is installed in a room of volume between 5 m3 and 10 m3 an  
air vent of effective area of 50 cm2 is required, while if the volume exceeds 11 m3 no  
air vent is required.  
However, if the room has a door which opens directly to the outside no air vent is  
required even if the volume is between 5 m3 and 11 m3.  
If there are other fuel burning appliances in the same room, B.S. 5440 Part 2  
Current Edition, should be consulted to determine the requisite air vent requirements.  
For appliances installed in the Republic of Ireland please refer to the NSAI- Domestic  
Gas Installation I.S. 813 Current Editions Table Four.  
Location  
The hob may be located in a kitchen, a kitchen/diner or bed sitting room, but not in  
a bathroom or shower room.  
Before making the cut out in the worktop ensure that there is a minimum distance  
of 55 mm between the rear edge of the hob and the wall.  
A minimum distance of 150 mm must be left between the side edges of the cut out  
and any adjacent cabinets or walls.  
The minimum distance combustible material can be fitted above the hob in line  
with the edges of the hob is 400 mm If it is fitted below 400 mm a space of 50 mm  
must be allowed from the edges of the hob.  
The minimum distance combustible material can be fitted directly above the hob is  
700 mm.  
For appliances installed in the Republic of Ireland please refer to NSAI- Domestic  
Gas Installation I.S 813 Current Edition Section 7- Permitted Locations of Appliance.  
18 electrolux  
CLEARANCES  
REQUIRED  
CLEARANCES  
REQUIRED  
WHEN FITTING THE GAS HOB  
WHEN FITTING THE GAS HOB  
WITHOUT  
A
COOKER HOOD ABOVE  
WITH  
A
COOKER HOOD ABOVE  
700 mm  
700 mm  
400 mm  
50 mm  
400 mm  
50 mm  
55 mm  
55 mm  
400 mm  
400 mm  
100 mm  
100 mm  
50 mm  
50 mm  
Installation  
IMPORTANT  
This hob must be installed by a competent person to the  
relevant Gas Standards.  
Any gas installation must be carried out by a registered  
competent person.  
Please, ensure that, once the hob is installed, it is easily accessible for the  
engineer in the event of a breakdown.  
The manufacturer will not accept liability, should the above instructions or  
any of the other safety instructions incorporated in this instruction booklet  
be ignored.  
electrolux 19  
On the end of the shaft, which includes the G 1/2" threaded elbow,  
adjustment is fixed so that the washer is fitted between the components  
as shown in the diagram. Screw the parts together without using excessive  
force.  
FO 0264  
A) End of shaft with nut  
B) Washer  
C) Elbow  
Gas Connection  
Connection to the gas supply should be with either rigid or semi-rigid pipe, i.e.  
steel or copper.  
The connection should be suitable for connecting to R 1/2 (1/2 BSP male thread).  
When the final connection has been made, it is essential that a thorough leak test  
is carried out on the hob and installation.  
Ensure that the main connection pipe does not exert any strain on the hob.  
It is important to install the elbow correctly, with the shoulder on  
the end of the thread, fitted to the hob connecting pipe.  
Failure to ensure the correct assembly will cause leakage of gas.  
20 electrolux  
Cut out size  
The dimensions of the cut-out are given in the diagram.  
480  
830  
150 min  
electrolux 21  
Building In  
Building over a cupboard or drawer  
If the hob is to be installed above a cupboard or drawer it will be necessary to fit a  
heat resistant board below the base of the hob on the underside of the work surface.  
It is also recommended to carry out the electrical connection to the hob as shown  
in diagrams 1 and 2.  
Building over a kitchen unit  
with door  
1
ON/OFF SWITCH  
Proper arrangements must be taken in  
designing the furniture unit, in order to avoid  
any contact with the bottom of the hob which  
can be heated when it is operated. The  
recommended solution is shown in diagram 3.  
FLEX  
OUTLET  
The panel fitted under the hob ("a") should  
be easily removable to allow easy access if  
technical assistance is needed. The space  
behind the kitchen unit ("b") can be used for  
connections.  
Dimensions are given in mm.  
ON/OFF SWITCH  
2
3
FLEX  
OUTLET  
22 electrolux  
Fitting the hob into the worktop  
Carry out the building in of the hob  
as follows:  
1. place the seals supplied with  
the hob on the front edge of  
the cut out. Then, place them  
at 27 mm from the side  
edges and at 10 mm from the  
rear edge, as shown in the  
diagram, taking care that the  
seals  
meet  
without  
overlapping.  
27  
27  
2. Place the hob in the cut out,  
taking care that it is centred.  
3. Fix the hob with the relevant  
fixing clamps, supplied with  
the injectors kit (see diagram).  
When the screws have been  
tightened, the excess seal can  
be removed.  
Seal  
The edge of the hob forms a double  
seal which prevents the ingress of  
liquids.  
electrolux 23  
Electrical connections  
Any electrical work required to install this hob should be  
carried out by a qualified electrician or competent person,  
in accordance with the current regulations.  
THIS HOB MUST BE EARTHED.  
The manufacturer declines any liability should these safety measures not  
be observed.  
This hob is designed to be connected to a 230 V 50 Hz AC electrical supply.  
Before switching on, make sure the electricity supply voltage is the same  
as that indicated on the hob rating plate. The rating plate is located on the  
bottom of the hob. A copy is attached on the back cover of this book.  
The hob is supplied with a 3 core flexible supply cord incorporating a 3  
amp plug fitted. In the event of having to change the fuse, a 3 amp ASTA  
approved (BS 1362) fuse must be used.  
Should the plug need to be replaced for any reason, the wires in the mains  
lead are coloured in accordance with the following code:  
Green and Yellow  
Blue  
Brown  
- Earth  
- Neutral  
- Live  
1) Connect the green and yellow  
(earth) wire to the terminal in the  
plug which is marked with the  
letter 'E' or the earth symbol  
or coloured green and yellow.  
!
2) Connect the blue (neutral) wire to  
the terminal in the plug which is  
marked with the letter 'N' or  
coloured black.  
FO 0390  
3) Connect the brown (live) wire to the terminal in the plug which  
is marked with the letter 'L' or coloured red.  
Upon completion there must be no cut, or stray strands of wire present  
and the cord clamp must be secure over the outer sheath.  
A cut off plug inserted into a 13 amp socket is a serious  
safety (shock) hazard. Ensure that the cut off plug is disposed  
of safely.  
24 electrolux  
The replacement of electric cable must be carried out ex-  
clusively by the service force centre or by personnel with  
similar competencies, in accordance with the current regu-  
lations.  
Permanent Connection  
In the case of a permanent connection, it is necessary that you install a  
double pole switch between the hob and the electricity supply (mains),  
with a minimum gap of 3 mm between the switch contacts and of a type  
suitable for the required load in compliance with the current electric  
regulations.  
The switch must not break the yellow and green earth cable at any point.  
Ensure that the hob supply cord does not come into contact  
with surfaces with temperatures higher than 50 deg. C.  
electrolux 25  
Wiring diagram  
26 electrolux  
Fault finding  
Preliminary Electrical Systems Check  
Blue  
Brown  
Green  
Yellow  
START  
Isolate appliance  
and carry out:  
A: Earth Continuity  
check.  
Blue  
Green  
Yellow  
Brown  
YES  
NO  
Carry out:  
C: Polarity check.  
Carry out:  
D: Resistance to  
Earth check.  
Has inlet fuse blown?  
NO  
Electricity supply  
should now be  
satisfactory.  
YES  
PLUG (with cover removed)  
Earth Wire  
SOCKET  
(face view)  
Inlet wiring  
faulty.  
Rectify any  
fault.  
Green/Yellow  
( )  
( )  
E
Neutral Wire  
Blue  
N
L
Isolate appliance and  
carry out:  
B: Insulation check.  
Rectify any fault  
including replacing  
fuses as necessary.  
electrolux 27  
A. EARTH CONTINUITY CHECK  
Appliance must be electrically disconnected - meter set on W (Ohms)  
x 1 scale and adjust zero if necessary.  
Test leads from any appliance earth point to earth pin on plug.  
Resistance should be less than 0.1 W (Ohm), check all earth wires  
for continuity and all contacts clean and tight.  
B. INSULATION CHECK  
Appliance electrically disconnected, all switches ON.  
a) meter set on W (Ohms) x 1 scale.  
Test leads from L to N in appliance terminal block. If meter reads  
«0» then there is a short circuit.  
b) meter set on W (Ohm) x 100 scale.  
Repeat test with leads from L to E. If meter reads less than ×  
(infinity) there is a fault.  
NOTE - Should it be found that the fuse has failed but no fault is indicated  
- a detailed continuity check (i.e. by disconnecting and checking each  
component) is required to trace the faulty component.  
It is possible that a fault could occur as a result of local burning/arcing but  
no fault could be found under test. However a detailed visual inspection  
should reveal evidence of burning around the fault.  
28 electrolux  
Ignition System / Gas Ignition  
YES  
Check gas supply at  
burner  
Ignitor does not spark  
NO  
Check plug top fuse and  
replace if necessary  
Light burner manually  
Check polarity and  
earth continuity of  
supply point  
Check by pass simmer  
adjusted  
Check fitting  
of burners  
Check position of the  
electrode  
Check earth continuity  
of appliance  
Check continuity from 'N' on the  
mains connector block and "O" on  
the ignitor unit  
Check continuity from the tip of  
each electrode to the terminals  
1 to 4 on the ignitor unit  
Check continuity from 'L' on the  
mains connector block and the  
taps ignition switches  
Check for breaks in the  
insulation of the HT leads  
Check continuity from ignition  
switches connector to ignitor unit  
Change the ignitor unit  
electrolux 29  
Commissioning  
When the hob has been fully installed it will be necessary to check the  
minimum flame setting. To do this, follow the procedure below.  
1) Turn the gas tap to the MAX position and ignite.  
!
2) Set the gas tap to the MIN flame position then turn the control  
knob from MIN to MAX several times. If the flame is unstable or is  
extinguished follow the procedure below.  
Procedure:  
1) Re-ignite the burner and set  
!
to MIN.  
2) Remove the control knob.  
3) To adjust, use a thin bladed  
screwdriver and turn the  
adjustment screw (see  
diagram) until the flame is  
steady and does not  
Minimum adjustment  
extinguish, when the knob is  
screw  
turned from MIN to MAX.  
Repeat this procedure for all  
burners.  
Pressure Testing  
The pressure testing must becarried out on the burners.  
Proceed as follows:  
!
1) Remove the pan supports and the burner caps and crowns.  
2) Fit manometer tube over the injector.  
3) Turn on the burner gas supply and ignite another burner supply.  
The pressure reading should be nominally 20 mbar and must be  
between 17 mbar and 25 mbar.  
4) Turn off the burner supplies.  
30 electrolux  
Conversion from natural gas to LPG  
IMPORTANT  
The replacement/conversion from natural gas to LPG should only  
be undertaken by a competent person.  
It is important to note that this model is designed for use with natural gas but can be  
converted for use with butane or propane gas providing the correct injectors are  
fitted. The gas rate is adjusted to suit.  
Method  
1) Ensure that the gas taps are in the 'OFF' position  
!
2) Isolate the hob from the electricity supply  
3) Remove all pan supports, burner caps, rings, crowns and control knobs.  
4) With the aid of a 7mm box spanner the burner injectors can then be  
unscrewed and replaced by the appropriate LPG injectors.  
TO ADJUST THE GAS RATE  
With the aid of a thin bladed screwdriver completely tighten down the by  
pass adjustment screw. Upon completion stick the replacement rating plate  
on the under side of the hob.  
!
electrolux 31  
Standard guarantee conditions  
We, Electrolux, undertake that if within 12 months of the date of the purchase this  
Electrolux appliance or any part thereof is proved to be defective by reason only of  
faulty workmanship or materials, we will, at our option repair or replace the same  
FREE OF CHARGE for labour, materials or carriage on condition that:  
•The appliance has been correctly installed and used only on the gas and electricity  
supply stated on the rating plate.  
•The appliance has been used for normal domestic purposes only, and in accordance  
with the manufacturers instructions.  
•The appliance has not been serviced, maintained, repaired, taken apart or tampered  
with by any person not authorised by us.  
•Electrolux Service Force Centre must undertake all service work under this  
guarantee.  
•Any appliance or defective part replaced shall become the Companys property.  
•This guarantee is in addition to your statutory and other legal rights.  
Exclusions  
•Damage or calls resulting from trans-portation, improper use or neglect, the  
replacement of any light bulbs or removable parts of glass or plastic.  
•Costs incurred for calls to put right an appliance which is improperly installed or  
calls to appliances outside the United Kingdom.  
•Appliances found to be in use within a commercial environment, plus those which  
are subject to rental agreements.  
•Products of Electrolux manufacturer that are not marketed by Electrolux.  
32 electrolux  
Service and Spare Parts  
In the event of your appliance requiring service, or if you wish to purchase spare  
parts, please contact your local Service Force Centre by telephoning  
0870 5 929 929  
Your telephone call will be automatically routed to the Service Force Centre co-  
vering your postcode area.  
For the address of your local Service Force Centre and further information about  
Service Force, please visit the website at  
Before calling out an engineer, please ensure you have read the details under the  
heading “Something not working”. When you contact the Service Force Centre you  
will need to give the follo-wing details:  
1.Your name, address and postcode.  
2.Your telephone number.  
3. Clear concise details of the fault.  
4. The model and Serial number of the appliance (found on the rating plate).  
5.The purchase date.  
Please note a valid purchase receipt or guarantee documentation is required for in  
guarantee service calls.  
Customer Care  
For general enquiries concerning your Electrolux appliance, or for further  
information on Electrolux products please contact our Customer Care  
Department by letter or telephone at the address below or visit our website  
Customer Care Department  
Electrolux Major Appliances  
Addington Way  
Luton  
Bedfordshire, LU4 9QQ  
Tel: 08705 950 950 (*)  
(*) Calls may be recorded for training purposes  
electrolux 33  
European guarantee  
This appliance is guaranteed by Electrolux in each of the countries listed  
at the back of this user manual, for the period specified in the appliance  
guarantee or otherwise by law. If you move from one of these countries to  
another of the countries listed below the appliance guarantee will move  
with you subject to the following qualifications:  
• The appliance guarantee starts from the date you first purchased the  
appliance which will be evidenced by production of a valid purchase  
document issued by the seller of the appliance.  
• The appliance guarantee is for the same period and to the same extent  
for labour and parts as exists in your new country of residence for this  
particular model or range of appliances.  
• The appliance guarantee is personal to the original purchaser of the  
appliance and cannot be transferred to another user.  
• The appliance is installed and used in accordance with instructions  
issued by Electrolux and is only used within the home, i.e. is not used  
for commercial purposes.  
• The appliance is installed in accordance with all relevant regulations in  
force within your new country of residence.  
The provisions of this European Guarantee do not affect any of the rights  
granted to you by law.  
34 electrolux  
electroux 35  
35693-2601  
03/07  
R.0  

Hotpoint E6011 User Manual
FirmTek Computer Hardware 2SE2 E User Manual
Cypress 7C185 35 User Manual
Bosch Appliances Glass Ceramic s NEM93UC User Manual
Black Box Ultra2 LVD SCSI Cables and Terminators User Manual
Black Box Computer Hardware LBPS311A User Manual
Behringer Europower PMX3000 User Manual
Asus Motherboard H61MAUSB3 User Manual
Asus Computer Hardware SABERTOOTHZ77 User Manual
Adaptec Computer Hardware 1430SA User Manual