Eizo T68 User Manual

English

User's Manual

F67/FX·D7

T68/TX·D7

Color Display M onitor

2-5 Other Settings ................................................. 33

Degaussing ..................................................................... 33

Input Priority .................................................................... 33

Beep ................................................................................ 34

Menu Position, Menu Contrast ........................................ 35

Signal Filter ..................................................................... 35

Reset ............................................................................... 35

3 TROUBLESHOOTING _________________ 36

3-1 Troubleshooting ............................................... 36

4 GETTINGTHE MOST FROMYOUR MONITOR

____________________________________ 43

4-1 Adjustment Lock .............................................. 43

4-2 Connecting two PCs to the Monitor................. 43

4-3 Optional i·Sound Sound Unit ........................ 44

4-4 Making use of USB (Universal Serial Bus) ...... 44

5 CLEANING __________________________ 48

6 SPECIFICATIONS _____________________ 49

T68/TX·D7.............................................................. 49

F67/FX·D7.............................................................. 50

APPENDIX______________________________ i

may be reproduced, stored in a retrieval system, or transmitted, in any form or by any means, electronic,

mechanical, or otherwise, without the prior written permission of EIZO NANAO CORPORATION.

EIZO NANAO CORPORATION is under no obligation to hold any submitted material or information

confidential unless prior arrangements are made pursuant to EIZO NANAO CORPORATION's receipt of

said information.

Although every effort has been made to ensure that this manual provides up-to-date information, please note

that EIZO monitor specifications are subject to change without notice.

ENERGY STAR is a U.S. registered mark.

Apple and Macintosh are registered trademarks of Apple Computer, Inc.

DPMS is a trademark and VESA is a registered trademark of Video Electronics Standards Association.

Windows is a registered trademark of Microsoft Corporation.

ScreenManager, PowerManager, QuickSet, i·Sound and i·Station are trademarks of EIZO NANAO CORPORATION.

FlexScan, SuperErgoCoat and EIZO are registered trademarks of EIZO NANAO CORPORATION.

CONTENTS

PRECAUTIONS

IMPORTANT!

* This product has been adjusted specifically for use in the region to which it was originally

shipped. The performance of the product, (i.e. picture geometry, picture positioning and color

convergence and purity in the case of color monitors) is optimally adjusted to the earth's

magnetic field of the specific destination. If operated outside the region to which it was

originally shipped, the product may not perform as stated in the specifications.

* The manufacturer is not responsible for damage or malfunction caused by improper

connection. The power cord should be connected directly to a standard wall power outlet.

Location of the caution statements

The equipment must be connected to a grounded main

outlet.

Jordet stikkontakt skal benyttes när apparatet tilkobles

datanett.

Apparaten skall anslutas till jordat nätuttag.

IMPORTANT!

To ensure personal safety and proper maintenance. Please

read this section and the caution statements on the monitor

(refer to the figure above).

This manual uses the safety symbols below. They denote critical

information.

Please read them carefully.

Indicates a prohibited action.

Indicates to ground for safety.

WARNING

Failure to abide by the information in a WARNING may result in

serious injury and can be life threatening.

CAUTION

Failure to abide by the information in a CAUTION may result in

moderate injury and/or property or product damage.

PRECAUTIONS

WARNING

• If the monitor begins to emit smoke, smells like something

is burning, or makes strange noises, disconnect all power

connections immediately and contact your dealer for

advice.

Attempting to use a malfunctioning monitor can be dangerous.

• Do not dismantle the cabinet or modify the monitor.

Dismantling the cabinet or modifying the monitor may result in

electric shock or burn.

• Keep small objects away from the monitor.

Small objects may accidentally fall through the ventilation slots

into the cabinet, leading to fire, shock, or equipment damage.

• Keep liquids away from the monitor.

Spillage into the cabinet may result in fire, electric shock, or

equipment damage.

If an object or liquid falls/spills into the cabinet, unplug the

monitor immediately. Have the unit checked by a qualified

service engineer before using it again.

• Place the monitor on a strong, stable surface.

A unit placed on an inadequate surface may fall, resulting in

injury or equipment damage.

If the monitor falls, disconnect the power immediately and have

the unit checked by a qualified service engineer before using it

again. Using a monitor after it has been dropped may result in

fire or electric shock.

• Keep the plastic packing bags away from children and

infants.

Plastic bags can be dangerous. To avoid danger of suffocation,

keep the bag away from babies and children.

• Keep power terminal covers for the optional i·Sound^ä

sound unit away from children and infants.

Children and infants may accidentally swallow the covers and

choke. If swallowed, consult a doctor immediately.

• The equipment must be connected to a grounded main

outlet.

PRECAUTIONS

• Use the enclosed power cord. If using the power cord

other than the enclosed one, use the following cord.

In USA and Canada:

* Rating: min. 125 V, 10 A * Length: max. 2.1 m

* Type:

SVT

* Plug type:NEMA 5-15P, Parallel blade, Grounding type, 125

V, 10 A

In Europe:

* Rating: min. 250 V, 10 A * Length: max. 2.1 m

* Type:

H05VV-F 3G 1 mm²

Use a plug type approved by the country where you use.

Failure to do so may cause fire or electric shock.

• Do not overload your power circuit, as this may result in

fire or electric shock.

• For proper connections of the power cord, be certain to

plug the power cord to the provided monitor connector and

directly to a wall outlet.

By not doing so may result in fire or electric shock.

• Handle the power cord with care.

* Do not place the cord underneath the monitor or other heavy

objects.

* Do not pull on the cord.

* Do not attempt to repair a damaged cord.

If the power cord becomes damaged, stop using it. Use of a

damaged cord may result in fire or electric shock.

• To disconnect the power cord, grasp the plug firmly and

pull.

Never tug on the cord, doing so may cause damage and could

result in fire or electric shock.

CAUTION

Be careful when taking the monitor out of the carton:

• Disconnect the power cord, signal cables and remove the

optional i·Sound^äsound unit and i·Station^äUSB hub (if

applicable) when moving the monitor.

Moving the monitor with the cord attached or lifting it by the

i·Sound sound unit or i·Station USB hub is dangerous. It may

result in injury or equipment damage.

PRECAUTIONS

• Handle with care when carrying the monitor

Note that the monitor is heavier at the front than at the rear. Do

not move it alone. Always work with another person.

The screen is optically coated to reduce glare. Keep hard objects

(such as buttons, tie pins, and other clothing accessories) away

from the screen surface to prevent scratches.

• Set the monitor in an appropriate location.

* Do not install in a dusty or humid environment.

* Do not place in a location where light shines directly on the

screen.

* Do not place near heat generating devices or a humidifier.

• Use an easily accessible power outlet.

This will ensure that you can disconnect the power quickly in

case of a problem.

• Do not sit on the cabinet or place any heavy objects on the

cabinet.

A unit with heavy objects on it may fall or be damaged and

result in injury.

• Do not block the ventilation slots on the cabinet.

* Do not place books or any other papers on the ventilation

slots.

* Do not install the monitor in a closed space.

* Do not use the monitor laying down or upside down.

* Do not remove the tilt-swivel stand.

Using the monitor in this way blocks the ventilation slots and

prevents proper airflow, leading to fire or other damage.

• Do not remove the tilt-swivel stand.

The stand is required to maintain clearance for the ventilation

slots on the bottom of the cabinet. Removing the stand will

block these slots and may result in fire or electric shock.

• Do not touch the plug with wet hands.

Touching the plug with wet hands is dangerous and can cause

electrical shock.

• At the end of the day or if you plan to leave the monitor

unused for an extended period, after turning off the power

switch disconnect the power cord from the wall socket so

that no power connections are made.

• Unplug the monitor before cleaning it.

Cleaning the monitor while it is plugged into a power outlet may

result in electric shock.

PRECAUTIONS

For users of the EIZO optional i·Sound sound unit

and i·Station USB hub

• When adjusting the viewing angle of the monitor,

do not do so by handling the sound unit or USB

hub.

Adjusting the monitor in this way may break the unit or

cause bodily injury.

Others

• Do not install the monitor within an area subject to strong

magnetic fields (for example, in the vicinity of a speaker,

except the optional i·Sound unit, or a high-voltage

transformer). Magnetic fields can cause noise, image

shaking, and other distortions.

• Generally, for maximum viewing comfort position the

monitor slightly below eye level. Staring at the monitor

for prolonged periods can cause eye strain. Be sure to take

adequate rests. (A 10-minute rest period each hour is

suggested.)

• Do not remove the covers to the power terminal for the

optional i·Sound speaker unit for any reason except to

attach the unit.

PRECAUTIONS

INTRODUCTION

About This Manual

This manual explains the precautions, features, specifications, and

operation of your EIZO monitor. For convenience, a “ScreenManager

Quick Reference” guide has been included which shows how to implement

basic adjustments with the ScreenManager utility.

•

This manual applies to the EIZO monitor models:T68, TX·D7, F67 and

FX·D7. Please note that there are some points which vary according to

the model.

Package Contents:

Monitor

Cleaning Cloth for

CRT Screen

Power Cord

Signal Cable

(MD-C87)

EIZO USB Cable

(MD-C93)

User’s Manual

ScreenManager

Quick Reference

EIZO FlexScan

CRT Utility Disk

Warranty

Registration Card

•

If any of the above-listed items are missing or damaged, please contact

your local dealer for assistance.

For information about Windows^®95/98 setup (Plug & Play), refer to the

README in the EIZO FlexScan CRT Utility Disk.

Connection to a Macintosh requires use of an optional Macintosh

adapter. Please consult EIZO dealer.

We recommend that you retain the original packing materials in case of

future need.

INTRODUCTION

1 INSTALLATION

1-1 Controls & Connectors

Front

(1)ScreenManager menu

The ScreenManager is used to adjust the image of the monitor. Adjust-

ments are made using the Control Pad (6) shown in diagram. See page

14 for further details.

(2)USB port with a drop down access lid (Downstream port x 1)

See page 44 for further details.

(3)BNC/D-SUB selection button

Selects BNC or D-Sub connector as active input. This feature is only

used when two computers are connected to the monitor.

(4)AUTO-SIZING button

Automatically centers the displayed image, bringing the image borders

into alignment with the monitor frame. See page 18.

(5)Power terminal covers for the optional i·Sound sound unit

(6)QuickSet^™Control pad(hereinafter “Control pad”)

Use the four arrow keys and the ENTER key to enter adjustments and

settings.

INSTALLATION

(7)Power indicator

Indicates the power-on status, as follows:

Solid green:

Power is ON (normal mode)

Flashing green: PowerManager Mode 1 (power-saving mode)

Yellow:

PowerManager Mode 2 (maximum power-saving)

(8)Power switch

Switches the monitor’s power ON and OFF.

Rear

(1)Power connector

Use the supplied power cord only.

(2)D-Sub mini 15 pin input connector

(3)BNC input connector

(4)Termination switch

Allows multiple monitors to be chained together (Default termination is

75 Ω).

(5)Maintenance port

Allows EIZO optional utilities to be attached.

(6)USB ports (Upstream port x1, Downstream ports x 3)

See page 44 for further details.

INSTALLATION

1-2 Connecting the monitor to the PC

1) Be sure that the power switches of both the PC and the monitor are

OFF.

2) Plug the power cord into the power connector at the rear of the monitor.

Then plug the other end of the cord into a power outlet.

3) Plug the signal cable into the connector at the rear of the monitor.

•

When connecting the signal cable or cable adapter, first check that the

shape at the cable side matches the shape at the connecting side.

After connecting, secure the connection with the screw-in fasteners.

4) Plug the other end of the cable into the video connector on the rear of

the PC. Refer to the figures below.

Standard PC graphics board

D-Sub

mini 15 pin

D-Sub

mini 15 pin

Standard PC graphics board

MD-C87 (enclosed)

INSTALLATION

Macintosh

You must connect an optional Macintosh adapter to the PC before

connecting the signal cable.

D-Sub 15 pin

D-Sub

mini 15 pin

Macintosh

MD-C87 (enclosed)

Macintosh Adapter (Optional)

5) Turn on the monitor power first, then switch on the PC power. The

monitor’s power indicator (LED) will light up (green). The monitor will

warm up briefly, then display an image. Whenever you finish your

operation, turn off the PC and the monitor.

•

If an image does not appear, make sure that all connections have been

made properly. Refer to the“TROUBLESHOOTING” section on page

36 for additional advice.

1-3 Setting the resolution

The following look-up table shows the maximum (Non-interlaced) vertical

refresh rates for this model with regard to standard resolutions set forth by

VESA. The best way to see if the monitor will work with a given resolu-

tion and rate, is to compare the vertical refresh rate of the graphics board

to the monitor’s range (Refer to the graphics board manual for specifica-

tions). If the refresh rate is within the specified range of the monitor, it

should operate properly.

Maximum Vertical Refresh rate (Hz)

Horizontal Scan

Frequency (kHz)

640x480 800x600 1024x768 1280x1024 1600x1200

30-96

160

144

118

INSTALLATION

2 SCREEN ADJUSTMENT

2-1 How to use the ScreenManager

ScreenManager Menus

ScreenManager consists of a main menu and six sub menus: “Screen”,

“Color”, “PowerManager”, “Others”, “Information” and “Language.”

Animated icons on each menu allow for easy adjustment.

Main menu

•

The menu message for the ScreenManager can be displayed in six

languages: English, German, French, Italian, Spanish and Swedish.

First, select the preferred language through the “Language” menu. This

will become the default language when you use the ScreenManager.

Sub menus

Menus

Functions

Reference

Page 19

Brightness/Contrast,

Horizontal/Vertical Size,

Position, Side Pin-cushion/

Trapezoidal adjustment, Tilt,

Uniformity, Convergence

and Moiré Reduction.

Page 23

<Color>

Standard color with

selection of color

temperature and Custom

color with adjustment of

color tone.

Entering the ScreenManager

SCREEN ADJUSTMENT

Menus

Functions

Reference

Page 28

Power saving settings.

Page 33

Degauss, Input-signal priority

selection for two signal

connections, Beep ON/OFF,

ScreenManager menu

position, Contrast

adjustment, Signal filter

setting and Reset to defaults.

This menu shows the current

ScreenManager settings. The menu

contains four pages. Pressing the ENTER

key displays the following

information:

• Page 1:Input port, horizontal and

vertical frequencies, moiré

reduction setting

• Page 2:Color-adjustment settings

• Page 3:PowerManager settings

• Page 4:Input priority (see note), beep

and Signal filter setting

• The current ScreenManager setting is

displayed even if the input selection

has been manually overridden by the

use of the BNC/D-Sub selection

button.

First select the preferred language to

use. Six languages are available to

choose from: English, German, French,

Spanish, Italian and Swedish. The

ScreenManager’s messages will appear

in the selected language.

SCREEN ADJUSTMENT

Press the ENTER key to display the ScreenManager Main menu.

Enter the Settings

Use the Control pad (the four arrow keys and the ENTER key) to make the

required adjustments and settings.

ENTER key

Arrow keys

Save & Exit

To return to the previous menu, select the Return icon (or push the “down”

arrow key twice), then push the ENTER key.

To save settings and exit the ScreenManager, select the Exit icon and press

the ENTER key.

Shortcut Keys

SCREEN ADJUSTMENT

Before entering the ScreenManager, brightness and contrast can be

adjusted directly by moving the Control pad. To record the new setting

and exit the ScreenManager, press the Enter key. (The brightness and

contrast functions are also available in the ScreenManager “Screen”

menu.) See the diagram described below for adjustment directions.

Brightness

Contrast

Down

Contrast

Brightness

Down

SCREEN ADJUSTMENT

2-2 Imaging adjustment

Using the AUTO-SIZING button

After connecting the monitor to the PC, first press the AUTO-SIZING

button on the front panel. The AUTO-SIZING function centers the

displayed image, aligning the image’s borders with respect to the monitor

frame.

In general, press the AUTO-SIZING button whenever changing the

graphics board or the resolution or when image size and/or position is

incorrect.

If further adjustment is required, adjust the picture size/position as desired

using the Size/Position function in the ScreenManager “Screen” menu.

Refer to the next page.

•

The AUTO-SIZING function is intended for use on Macintosh, and IBM

compatibles running Windows. It may not work properly if either of the

following applies:

- An AT-compatible PC running MS-DOS (not Windows).

- The background color for the “wallpaper” or “desktop” pattern is set

to black.

•

Some signals from the graphics board may not function properly.

A solid-color screen (i.e. red, green, blue) may appear for an instant

while performing the AUTO-SIZING function, this phenomenon is not a

failure.

SCREEN ADJUSTMENT

- Screen menu -

All of the icons shown in the ScreenManager “Screen” menu are described

below.

•

Allow the monitor to stabilize for at least 30 minutes before making

image adjustments.

Brightness, Contrast, Size, Position

These functions are used to adjust the brightness, contrast, size and position

of the screen.

Proper adjusting for brightness & contrast

1) Set the brightness and contrast to their maximum settings.

2) Set the display area to the minimum size. A black-and-white back-

ground (called a Raster) appears behind the display area.

3) Adjust the brightness so that the color of the Raster comes as close as

possible to the color of the undisplayed area. This setting provides the

sharpest contrast.

4) Restore the preferred display size either by pressing the AUTO-SIZING

button or by adjusting the size and position via the ScreenManager

menu.

5) Adjust the contrast as desired.

Display Area

Raster

Undisplayed area

SCREEN ADJUSTMENT

•

If you use the white text against a black background like DOS text, we

recommend that you set the brightness to its maximum setting because

the dark setting will result in eye strain due to high character contrast.

Geometry,Tilt, Uniformity

Image distortion, tilting and/or the imbalance of brightness/whiteness over

the entire screen may be caused by the Earth’s magnetic field depending on

the direction the monitor is facing.

Use the “Screen” menu’s geometry (Side-Pincushion, Side-Pin Balance,

Trapezoidal, Parallelogram) and tilt adjustment function to correct any

geometric distortion and tilting.

The “Uniformity” adjustment function adjusts the bright/white uniformity

in the corner of the screen. For adjustments, please follow the procedure

below.

1) Degauss the screen by using the “Degaussing” function in the

ScreenManager’s “Others” menu.

2) Select the “Uniformity” function and adjust the screen so that the

imbalance of brightness/whiteness over the entire screen will be

minimized.

3) After performing the above adjustment, the screen image somewhat

tilts. This can be corrected by using the “Tilt” adjustment function.

Image distortion, tilting and/or the imbalance of brightness/whiteness may

also be caused by any device that generates a magnetic field. If the above

adjustments are not effective, try the following approaches.

•

Check to see if there are any nearby interfering electronic devices such

as another monitor, an electric motor, or a speaker (other than an

optional EIZO i·Sound speaker unit). If so, move the device or move

the monitor.

•

It is sometimes possible to correct distortion, tilting or the imbalance of

brightness/whiteness by reorienting the monitor.

SCREEN ADJUSTMENT

Convergence

Displayed characters and images may appear fuzzy or have tinges of red,

green, or blue if the electron beams do not converge correctly. These can be

adjusted by the convergence adjustment feature in the ScreenManager.

What is convergence?

Convergence is the monitor’s ability to precisely illuminate specific

phosphors and line them up properly in order to produce pure color.

In order to properly adjust convergence, it is best to have an image that

makes it easy to see any convergence error. A black background with

white letters or lines is the best. This could be a DOS text mode or an

image created with a “paint” program.

When adjusting convergence, look at the adjustment across the whole

screen. When adjusting horizontal convergence, look at the left and right

edges of vertical lines or characters. When adjusting vertical

convergence, look at the top and bottom edges of horizontal lines or

characters. Proper adjustment is when the effect of red and blue tinges are

minimized.

•

The convergence adjustment adjusts the entire screen. It is not

possible to limit adjustment to specific screen areas.

SCREEN ADJUSTMENT

Moiré Reduction

What is moiré?

Moiré refers to an interference pattern of dark wavy lines on the screen.

It is not a defect, but rather an interference phenomenon caused by the

relationship between the phosphor layout and the imaging signal. Moiré

is often an indication of a good focus level. Moiré is particularly

noticeable when using a light-gray or every-other-dot pattern back-

ground. Although moiré can not be eliminated, it can be reduced with

the moiré reduction feature.

(Moiré)

(Every-other-dot pattern)

Moiré can be reduced in a variety of ways.

1) Adjust with the ScreenManager’s moiré reduction function.

Adjust so that moiré becomes almost unnoticeable. Before adjusting, set

the desktop to an every-other-dot pattern (see picture above) so that

moiré will be visible. Following the adjustment, change to a different

desktop background to reduce moiré even further.

2) Change the horizontal and vertical dimensions.

Adjust the horizontal and vertical dimensions of the display area as

necessary to reduce moiré.

3) Change the selected desktop or wallpaper pattern.

Use the PC software to change the desktop or wallpaper pattern. Any

solid color pattern is recommended. For detailed information on how to

change these patterns, refer to the documentation for the PC and

operating system.

•

The screen image may shake slightly while the ScreenManager moiré

reduction function is ON. Switching the function OFF will improve image

stability and clarity at the expense of slightly greater moiré.

SCREEN ADJUSTMENT

2-3 Color Adjustment

- Color menu -

Outline

EIZO monitors have incorporated two color adjustment mode, standard

and custom. The “Standard” mode allows the adjustment of the color

spectrum. The “Custom” mode allows extensive controls over the colors of

the displayed image on the screen.

All adjustments for either mode can be made quickly and easily through the

ScreenManager “Color” Menu - offering a tool to create customized color

environment.

Please find the details of the color mode adjustment capabilities below:

Contents

Standard mode

Application

For routine work and

printing.

Sets color temperature.

Temperature can be set from 4000K to

10000K, in 500K increments. (Additionally,

industry standard of 9300K is set as default.)

Custom mode

For use when high

precision color

Sets color temperature.

adjustment is necessary

(i.e. when there is a need

to obtain identical colors

on multiple monitors* or

match the display color

with printout color**.)

Allows for specific adjustments to Red,

Green and Blue (R/G/B). This consists of

the Cutoff and Gain functions.

* The color adjustment spectrum may vary between monitors.

** A color calibrator can be used for even higher-precision color adjust-

ment.

SCREEN ADJUSTMENT

•

Each monitor is slightly different, if two monitors are set to the same

color temperature value (i.e. 6500K), they may not necessarily look the

same.

Adjusting the Standard mode

C o l o r

T e m p r a t u r e

•

Users should allow at least 30 minutes for the monitor to stabilize before

setting the color adjustments or color matching.

Procedure

1) Go to the “Color” menu.

2) Select the “Standard mode” setting from the “Color mode” menu.

3) Select the “Temperature” icon. A color temperature bar will appear.

4) Adjust the temperature by using the right or left Arrow keys.

5) Press the ENTER key to save the data.

What is color temperature?

Color temperature is a method to measure the white color tone,

generally indicated in degrees Kelvin. At high temperatures the white

tone appears somewhat blue, while at lower temperatures it appears

somewhat red. Computer monitors generally give best performance at

high temperature settings.

5000K: Slightly reddish white. Often used in printing industry.

6500K: Warm-white tone, similar to white paper or daylight. This

temperature is good for video-image display.

9300K: Slightly bluish white. This is the default setting for your EIZO

monitor.

SCREEN ADJUSTMENT

Adjusting the Custom mode

Cutoff and Gain adjustments

Monitors use red, green and blue (R, G, and B) to convey color

information. They use an additive method to combine different

amounts of the primary colors to produce a desired color. In other

words, monitors start with no light (black) and add percentages of red,

green and blue to make colors. White is usually produced by adding the

same amount of all three colors, where black is usually produced by

adding no color.

However, colors are not only determined by the balance but also the

intensities of R, G, and B (how bright they are) which we call Gain, and

the saturation of R, G and B (how vivid or dull they are) which we call

Cutoff.

•

Users should allow at least 30 minutes for the monitor to stabilize before

setting the color adjustments or color matching.

Before you attempt to change the colors, always start with the color

settings set to the “default settings” by using the “Reset” function in the

ScreenManager “Others” menu.

•

If only a quick setting is required, that is close to the desired color, but

not exact, skip making any changes to the Cutoff adjustment (step 4).

If a precise match is desired, adjustment of the Cutoff levels must be

made. We recommend that for exact matching, use a color calibrator.

Procedure

1) For optimum results, before beginning the custom color adjustment, go

to the “Screen” menu and set the display to maximum brightness and

contrast. (Use the “Screen” menu’s “Brightness” and “Contrast” icons.)

2) Then, return to the “Color” menu and select the “Custom mode”

setting.

3) Set the color temperature.

SCREEN ADJUSTMENT

a) Select the “Temperature” icon from the sub menu.

b) Select the temperature as desired by moving the arrow keys in any

direction.

4) Adjust the Cutoff

Cutoff

The Cutoff adjustment is the most powerful adjustment. It alters the

starting point (the black level) and the ending point (the white level).

If the Cutoff level for color is raised or lowered, black, white, and all

levels between are raised or lowered by the same degree.

Before adjusting the Cutoff, it is best to display a screen with a black

background (such as the DOS command screen).

a) Select “Cutoff” icon. The screen shown on the left will appear.

b) Adjust each color until you can create a uniform black screen.

5) Adjust the Gain

Gain

The Gain adjustment has no effect on the starting point (the black

level). It changes only the ending point (the white level). The Gain

adjustment is used to fine tune the whites and light grays to a good

balance.

Before adjusting the Gain, it is best to display a screen image that has a

white or grayscale background, such as the operating window for

Windows.

a) Select “Gain” icon. The screen shown on the left will appear.

b) Adjust each color until you can create a uniform white screen.

6) To register the adjustment, select the “Save” icon and then press the

ENTER key. If the settings are not saved, all adjustments will be lost.

7) Finally, readjust the contrast in the “Screen” menu to get the best image

clarity.

•

If an inappropriate adjustment is made, corrections can be made by

repeating the above procedure starting from Step 3 (temperature

setting).

The values shown in percentages (%) for both the Cutoff and Gain

adjustments represent the current level within the specific adjustment

only. They are available only as a reference tool. (To create a uniform

white or black screen, the percentages for each will probably not be the

same.)

SCREEN ADJUSTMENT

•

These diagram explains how the color curves were changed for the

best adjustment in steps 4 and 5.

Adjust the white level so

that the high end of the

curve for each color

(R,G,B) is equal as see

picture 3.

Adjust the black level

so that the low end of

the curve for each

color (R,G,B) is equal

as see picture 2.

This setup gives the best

color balance.

What is the relation between the color and the brightness adjustment?

Brightness uniformly adjusts the amount of light output for the entire

screen and its background. If it is increases too high the background

will become white, too low and many dark colors will not be displayed.

It affects all color controls.

Contrast varies the difference in light output from the lowest to the

highest screen intensities. It is the brightness adjustment for the video

signal area.

After making the color settings, readjust the contrast to get the best

definition and intensity of the colors for the displayed image.

SCREEN ADJUSTMENT

2-4 Power-save Setup

- PowerManager menu -

What is PowerManager?

The PowerManager feature automatically reduces the monitor’s

power consumption during idle periods, in accordance with the PCs

ScreenSaver software.

There are two PowerSaving modes in the EIZO PowerManager:

Mode 1 and Mode 2. Even if the monitor is in a power saving mode,

it will return to a normal display immediately when the mouse or

keyboard is operated.

The EIZO PowerManager functions comply with NUTEK and VESA

DPMS standard.

Power consumption:

Normal operation : 120 W

PowerManager Mode 1: less than 10 W *

(Power Indicator flashing green)

PowerManager Mode 2: less than 3 W *

(Power Indicator solid yellow)

* When the USB hub is not connected

As an ENERGY STAR^®Partner, EIZO NANAO CORPORATION has

determined that this product meets the ENERGY STAR^®guidelines for

energy efficiency.

•

Do your part to conserve energy, turn off the monitor when your

finished using it. Complete energy use can only be stopped by

disconnecting the monitor from the power supply.

Even if the monitor is in a power saving mode, USB compliant

devices function when they are connected to the monitor’s USB (both

the upstream and the downstream ports). Therefore, power

consumption of the monitor will change according to the connected

devices even if the monitor is in a power saving mode.

•

When the monitor is in a power saving mode, the optional EIZO

i·Sound speaker unit will turn off.

SCREEN ADJUSTMENT

Set-up Procedure

Set the monitor’s power-save environment to match the PC’s ScreenSaver

software.

•

For the PC setup, please refer to the user’s manuals for the PC and

graphics board.

There are two power-save settings for the monitor.

“VESA DPMS” system works with the VESA DPMS signal.

“NUTEK”s system works with a screen saver software and Energy Saver

for Macintosh which blanks the screen (totally black screen).

Set the monitor to match the PC’s power-saving software, as follows.

Monitor setting for matching the PC:

PC Power saving

Monitor setting

VESA DPMS

PC/AT and compatibles

(VESA DPMS activated)

VESA DPMS (Signal)

PC/AT and compatibles

(VESA DPMS

Windows

(Control Panel/Desktop/

ScreenSaver: “Blank Screen”)

NUTEK

inactivated)

Macintosh

Energy Saver

NUTEK

ScreenSaver software

After Dark/“Blank” settings

SCREEN ADJUSTMENT

VESA DPMS System

1) First, make the appropriate settings for the PC. (See note, page 29.)

2) Then select “VESA DPMS”.

3) Set the delay period, which is the interval that the monitor will wait

after receiving a power-save signal from the PC, before entering into

Mode 1 or Mode 2.

VESA DPMS power-saving method

VESA DPMS utilizes four signals: ON, STANDBY, SUSPEND, and OFF.

The monitor detects these signals from the graphics board and executes

power-saving accordingly, as illustrated below.

SCREEN ADJUSTMENT

NUTEK System

1) First make the appropriate ScreenSaver settings (Macintosh/Energy

Saver) for the PC.

2) Then select “NUTEK”.

3) Set the delay time, which is the interval between the time that the

ScreenSaver (Macintosh/EnergySaver) blanks the screen and the time

that the monitor enters Mode 1.

4) Set the Mode 1 duration time which is the user definable time (0-60

minutes) before the monitor enters Mode 2.

NUTEK power-saving method

Mode 1 operates for a user-definable period in “Duration” (in 0-60

minutes) before the monitor enters Mode 2. If the keyboard or the

mouse are not in use during this period, the monitor will then enter

PowerManager Mode 2.

SCREEN ADJUSTMENT

What is VESA DPMS?

The acronym VESA stands for “Video Electronics Standards

Association,” and DPMS stands for “Display Power Management

Signaling.” DPMS is a communication standard that PCs and

graphics boards use to implement power savings at the monitor side.

What is NUTEK?

NUTEK is the acronym for the Swedish National Board for Industrial

and Technical Development, an organization that works to promote

power-saving technologies.

What is ENERGY STAR?

“ENERGY STAR” is a set of power-saving guidelines issued by the

U.S. Environmental Protection Agency (EPA). The guidelines apply to

PC systems and peripherals.

AutoPower Function

Once the monitor’s main power has been switched ON, the monitor will

start up automatically whenever the PC is turned on. If the

PowerManager is set to VESA DPMS or NUTEK, the monitor will

automatically power down (to PowerManager Mode 2) when the PC is

turned off. If the PowerManager is set to OFF, however, the monitor

power will remain on even after the PC is switched off.

SCREEN ADJUSTMENT

2-5 Other Settings

- Others menu -

All of the icons shown in the ScreenManager “Others” menu are described

below.

Degaussing

The monitor automatically degausses every time the power is turned ON

and every time it is reactivated from the PowerManager power-saving

Mode 2. A degaussing function is provided in the ScreenManager for use

at other times. Note that the image vibrates slightly while degaussing is in

progress, but will return to normal when degaussing is completed.

•

The degauss circuitry takes about 30 minutes to regain maximum

power following degaussing before it can work again.

What is degaussing?

“Degaussing” refers to the process of removing magnetic-field effects

from the monitor. Operation of the monitor within a magnetic field

may adversely effect color purity. Degaussing can be used to correct the

problem.

Input Priority

This function is used to select which PC will have priority to control the

monitor when utilizing two PCs.

There are three settings available:

“D-Sub”, “BNC” or “Manual”. The default priority setting is “D-Sub”.

The monitor constantly checks the input signals and switches automatically

in accordance with the “Input Priority” settings (see chart on next page).

Once a priority is set, whenever a change of signal is detected at the

selected input, the monitor will switch the input to that signal.

SCREEN ADJUSTMENT

In the case of only one signal being present at either input, the monitor

automatically detects and displays that signal.

Priority setting

D-Sub

Performance

If signals from both inputs are present, the monitor

gives preference to D-Sub for the cases shown below:

• When the power of the monitor is turned ON (see

note 1).

• When the signal input to D-Sub is changed even if

active input was BNC.

If signals from both inputs are present, the monitor

gives preference to BNC for the cases shown below:

• When the power of the monitor is turned ON (see

note 1).

BNC

• When the signal input to BNC is changed even if

active input was D-Sub.

The monitor will not detect signals automatically in

this mode. Select the active input by pressing the

input signal selection button on the monitor’s front

panel.

Manual

1 The Input Priority function does not automatically reactivate when the

monitor has been in the power save mode.

2 The Input selection button on the front panel can be used to select

either D-Sub or BNC as the active input at any time.

Beep

Use this feature to set the beeper ON or OFF. If the beeper is ON, the

monitor will generate beep signals as shown below. If the beeper is OFF,

the monitor will not beep.

Short beep

• ScreenManager item selected.

• ScreenManager parameter adjusted to minimum

or maximum limit.

• BNC/D-Sub selection button pressed.

Long beep

• AUTO-SIZING button pressed.

• ScreenManager data-save executed.

Four short beeps • Monitor not connected correctly.

• PC turned off.

• Monitor received unsupported signal frequency.

SCREEN ADJUSTMENT

Menu Position, Menu Contrast

Use these functions to adjust the position and contrast of the

ScreenManager menu. The menu contrast can be set from level 0 (mini-

mum setting) to 5 (maximum setting).

Signal Filter

This monitor provides two display modes according to the characteristics of

each graphics board for displaying the image properly. If the characteris-

tics of the graphics board does not match those of the monitor, the

characters and images displayed may have a slight shadow on their right

side (refer to figure below). If this phenomenon is noticeable, use the

“Signal Filter” function. Select either mode 1 or mode 2, whichever

displays the image better.

Reset

Use this function to return all ScreenManager parameters (size, position,

geometry, color, PowerManager etc.) to their factory default settings.

Default settings are as follows.

•

Screen:

Color:

PowerManager:

Others:

Moiré = OFF

Standard/9300K

VESA/5 sec.

Input Priority = D-Sub

Beep = ON

Signal Filter = Mode 1

English

•

Language:

SCREEN ADJUSTMENT

3 TROUBLESHOOTING

3-1Troubleshooting

This page presents problems that can be corrected by the user. If a

problem persists even after applying the suggested remedies, contact an

EIZO dealer.

n Problems caused by incorrectly setting of the termination switch

Problems

1) Misconvergence of colors.

2) Focus is dull.

Points to check with possible solutions

•

The termination switch on the rear of the monitor

should be set to 75 Ω position (default) for connec-

tion to a single monitor.

3) PowerManager does not work

properly in VESA setting.

If it is set to the ∞ position when using a single

monitor, some problems like 1) ~ 4) may occur.

4) Slight shadow appears on the

edges of the screen image or

text. (only for the BNC

connections.)

Check that the switch position is set to 75 Ω

position.

n No picture

Problems

Points to check with possible solutions

1) Indicator status: OFF

2) Indicator status: GREEN

•

Check that the power cord is correctly connected.

Try pressing a key on the keyboard, or clicking the

mouse. (The screen-saver software may be active.)

•

Check brightness and contrast settings. Minimum

settings will cause screen to be blank.

3) Indicator status: YELLOW

Try pressing a key on the keyboard, or clicking the

mouse. (The screen-saver software may be active.)

If the problem persists, switch off the monitor power

for a few minutes, then switch it back on and try

again.

4) “No signal detected” error

message appears.

•

Check that the PC is switched ON.

Check that the signal cable is properly connected to

the graphics board or PC.

•

Check that the graphics board is correctly inserted

in the PC.

Switch the signal input by pushing the BNC/ D-Sub

selection button on the front control panel.

TROUBLESHOOTING

Problems

Points to check with possible solutions

5) “Out of range” error message

appears.

•

Use the graphics board’s utility software to change

the frequency setting. (Refer to the manual of the

graphics board.)

(Example)

Whenever an error signal message appears, the

signal frequency will be displayed in red.

• Error messages will remain on the screen for 30 seconds, and then disappear. An

error message may not appear at all if the signal frequency is extremely high or

extremely low.

n Imaging problems

Problems

Points to check with possible solutions

1) Display size and/or position

is incorrect.

•

Press the AUTO-SIZING button on the front panel.

See page 18.

Adjust the image size and/or position using the icons

in the ScreenManager “Screen” menu. See page 19.

2) The screen is partially dark.

The CRT is not warmed up. Allow 30 minutes for

the monitor to stabilize.

Degauss the screen. (Use the degaussing feature in

the ScreenManager’s “Others” menu. See page 33.)

This problem can be caused by the earth’s magne-

tism. Adjust the uniformity in the ScreenManager’s

“Screen” menu. See page 20.

3) The entire screen is dark.

•

Adjust the contrast and brightness using the

ScreenManager’s “Screen” menu. See page 19.

Some signal timings can be the cause of this

problem. To correct this, turn off the monitor, then

hold down the AUTO-SIZING button and “down”

arrow key while turning on the monitor again. This

will change the signal timing and brighten the

screen. If the above operation is repeated, the

screen becomes dark again.

TROUBLESHOOTING

Problems

Points to check with possible solutions

4) • The image vibrates on the

screen.

•

Use of the “Moiré Reduction” feature may cause a

slight vibration. To eliminate the vibration, switch

the feature OFF or reduce the moiré reduction level.

See page 22.

• A slight shaking movement

of the screen image or

text.

•

Check that the signal cable is properly connected to

the graphics board or PC.

Check that the graphics board is correctly mounted

in the PC.

The signal cable might be damaged. Please contact

the dealer.

The monitor may be located close to a device that is

generating a magnetic field. Such devices include

speakers (other than the EIZO optional i·Sound

speaker), electric motors, high-voltage cables, and

other monitors. It may be solved by switching off or

moving the interfering device, or by relocating the

monitor.

•

If the volume level of the EIZO optional i·Sound

speaker is too high, it may, in some cases, cause a

slight vibration. To eliminate, turn down the volume

of the speaker.

• A unstable signal from the graphics board may be the cause of the imaging problem 2)

when using the monitor with a high resolution or in a high refresh mode. (The video

signal from the graphics board might be made irregular due to the use of a high speed

dot clock.) Change the resolution or the refresh rate to another setting.

5) The image has a background

shadow.

•

Try adjusting the convergence in the

ScreenManager’s Screen menu.

See page 21.

•

This problem can occur when using BNC

connection and the termination switch is set

incorrectly. The termination switch should be set to

75 Ω for a connection to a single monitor. See page

11.

6) The characters and images

have a slight shadow on their

right side.

•

Change the mode of “Signal Filter” function in the

ScreenManager “Others” menu. See page 35.

TROUBLESHOOTING

Problems

Points to check with possible solutions

7) Moiré patterns are

distracting.

•

Go to the ScreenManager’s “Screen” menu. Switch

on the moiré reduction feature and adjust as

necessary. See page 22.

8) The image is flickering.

Flicker will occur with interlaced scanning, or non-

interlaced scanning with a low refresh rate. All

EIZO monitors are capable of reproducing high

refresh rates for non-interlaced scanning. If a

problem occurs when using a non-interlaced signal,

try adjusting the graphics board to increase the

refresh rate (if possible). Refer to the graphics board

manual for information.

Non-Interlaced / Interlaced

In a “non-interlaced” scan, the electric guns draw the entire image in one vertical

pass, with each pass covering every horizontal line.

In a “interlaced” scan, the guns draw the entire image by scanning vertically twice.

At the first scanning, the guns draw every other horizontal line. At the second, they

draw the other lines. Thus, in a “interlaced scan”, the image flickers more visibly

when compared with a “non-interlaced” scan.

Flicker

The term “flicker” refers to noticeable shimmering that occurs when the image on the

screen is redrawn (“refreshed”) too slowly. A refresh rate of 80 Hz means the image

is redrawn 80 times per second. Most people will notice flicker at image refresh rates

as high as 60 or 70 Hz, whereas refresh rates of 72 Hz or above usually is not

noticeable. Flicker is known to be the cause of visual fatigue.

n Color problems

Problems

Points to check with possible solutions

1) The entire screen appears

bluish or reddish.

•

The CRT is not warmed up. Allow 30 minutes for

the monitor to stabilize.

2) Color purity is not uniform.

•

Allow 30 minutes for the monitor to warm up.

Degauss the screen. (Use the degaussing feature in

the ScreenManager’s “Others” menu. See page 33.)

TROUBLESHOOTING

Problems

Points to check with possible solutions

3) Misconvergence of colors.

(red, green, blue)

•

Allow 30 minutes for the monitor to warm up.

Adjust the convergence using the Convergence

feature in the ScreenManager’s Screen menu. See

page 21.

•

This problem can occur when using a BNC

connection and the termination switch is set

incorrectly. The termination switch should be set to

75 Ω for connection to a single monitor.

Explanation of the Characteristics of CRTs

When the monitor is not fully warmed up, the screen may look slightly colored, e.g.

reddish or bluish. This phenomenon is due to the unstableness of the electron gun

during its warm-up period. Please wait for about 30 minutes until the monitor

stabilizes in order to gain its proper color.

n Others

Problems

Points to check with possible solutions

1) The monitor beeps or hums.

•

The monitor emits a humming noise when

executing automatic degaussing at power-ON.

This is not a problem.

•

The monitor beeps at any time. This is not a

problem. See page 34 for full details.

2) Control Pad “ENTER key”

does not operate.

The Adjustment Lock is probably on. To unlock:

switch off the monitor power, then hold down the

AUTO-SIZING button and switch the monitor back

on. See page 43.

3) AUTO-SIZING button does

not operate.

•

The Adjustment Lock is probably on. To unlock:

switch off the monitor power, then hold down the

AUTO-SIZING button and switch the monitor back

on. See page 43.

4) AUTO-SIZING button does

not work properly.

The Auto-sizing function is intended for use on the

Macintosh and on IBM compatibles running

Windows. It may not work properly if either of the

following applies.

- You are running an AT-compatible PC on

MS-DOS (not Windows).

- The background color for the “wallpaper” or

“desktop” pattern is set to black.

•

Some signals from graphics boards may not function

properly.

TROUBLESHOOTING

Problems

Points to check with possible solutions

• A solid-color screen (i.e. red, green, blue) may appear for an instant while perform-

ing the auto-sizing function, this phenomenon is not a failure.

5) Characters are too large.

•

Change the resolution of the graphics board to a

higher setting. (Refer to the manual for the graphics

board or PC.)

What is Resolution?

Resolution is expressed as the number of dots (pixels) displayed on the screen. A larger

number of dots produces a more sharply defined (a higher-resolution) image.

Note that for a given screen size the dot size decreases as the number of dots increases: a

640 × 480 (dot × line) resolution uses larger pixels than a 1024 × 768 resolution. The

display size of a given font therefore varies according to the resolution. Higher

resolutions allow you to display more information on the screen.

Changing the resolution

If you are using a Macintosh, you can change the resolution from the APPLE menu by

selecting “Option” from “Monitor” or “Sound & Display.” If you are using a PC other

than a Macintosh, refer to the manual for your PC or graphics board for information.

Please refer to both the graphics board and monitor manuals for the scanning frequency

compatibility.

Problems

Points to check with possible solutions

6) Two horizontal hairlines are

visible on the screen.

(only T68)

•

These are dampening wires. Dampening wires are

used to support the CRT’s aperture grille, and are

visible as thin dark lines across the screen. All

EIZO aperture-grille type CRTs include two such

horizontal wires.

The aperture grille itself is a grid of taut metal

filaments that spans the entire screen from top to

bottom.

TROUBLESHOOTING

Problems

Points to check with possible solutions

7) Faint black vertical lines are

visible on the screen.

(only T68)

•

The aperture grille may be misaligned. Shock or

vibration during transport may, in some cases,

cause the aperture grille to fall out of alignment.

The problem will appear as one or more faint

black lines across the screen.

If this problem occurs, it may be able to solved by:

•

degaussing the screen, or

lightly tapping (do not hit) the side of

the monitor.

If neither of these methods works, try executing

the following procedure.

1) Display a bright white field over the area where

the black line(s) appear, with a black field over

the unaffected areas. (Do this by opening a

bright-white window on top of a black desktop

or wallpaper background. Position the window

so that it just covers the area of misalignment.)

2) Set brightness and contrast to maximum values,

and keep the display ON until the problem is

corrected. Try tapping the side of the display

lightly to help expedite realignment. The white

field will heat up the misaligned area of the

grille, returning it to proper alignment.

•

For problems with the USB function, refer to the troubleshooting on page 47.

TROUBLESHOOTING

4 GETTING THE MOST FROM

YOUR MONITOR

4-1 Adjustment Lock

The ScreenManager operation can

be disabled by holding down the

AUTO-SIZING button while

switching on the monitor’s power.

This will disable (“lock”) the

ScreenManager and AUTO-SIZING

button, protecting from accidental

changes.

To unlock the buttons: switch the power off, then hold down AUTO-

SIZING button once again and turn the power back on.

Note that brightness and contrast can be adjusted using the short cut keys

(see page 17) even while the Control pad is locked. After making such an

adjustment, push the ENTER key to clear the brightness/contrast adjust-

ment menu from the screen. Also, the BNC/D-Sub Selection button can still

be used.

4-2 Connecting two PCs to the Monitor

(Example)

MD-C53A (optional)

Connect one PC to the monitor’s D-Sub connector and another to the BNC

connector. The BNC connection should be made with an EIZO BNC cable,

available as an option.

•

Be sure that the monitor and the PC are both switched off before

connecting them.

Be sure to connect the cable securely.

Selecting the active input

•

The BNC/D-Sub selection button

on the front panel can be used to

select either BNC or D-Sub

connection as the active input.

•

The ScreenManager’s “Input

Priority” setting (in the “Others”

menu) can be used to set up the

automatic selection of the input.

See page 33 for details.

GETTING THE MOST FROMYOUR MONITOR

4-3 Optional i·SoundÔ Sound Unit

The optional speaker system

i·Sound connects directly to the

monitor and can be used to support

multimedia applications. The unit

includes a microphone function.

For details, consult EIZO dealers.

4-4 Making use of USB (Universal Serial Bus)

- For USB compliant system environments-

This monitor provides a hub which supports the USB standard. When

connecting to a USB compliant PC or another hub, the monitor functions as

a hub to which the USB compliant peripherals can be connected. The USB

standardized connectors enable the easy connection with these peripherals.

As an added advantage, the monitor can be controlled from a PC with a

mouse or keyboard when utilizing the enclosed utility software

“ScreenManager Pro for USB”.

•

To utilize the USB hub function, the following system environment is

required.

•

PC equipped with USB ports or another USB hub connected to the

USB compliant PC

•

OS (Windows 98)/Mac OS 8.5.1 or newer

EIZO USB cable (MD-C93, enclosed)

•

The USB hub function may not work properly with some systems.

Please consult the manufacturer of each system for details about this

feature.

•

When the monitor is not on, the peripherals connected to the down-

stream ports will not operate.

Even if the monitor is in a power saving mode, USB compliant devices

will function when they are connected to the USB ports (both the

upstream and the downstream) of the monitor.

Monitor USB Function Setup

Before the setup, connect the monitor to the PC with the signal cable (see

page 12) and boot the PC.

(For Windows 98)

1) Insert the "EIZO FlexScan CRT Utility Disk" into the floppy disk drive.

2) Connect the upstream port of the monitor to the downstream port of

the USB compliant PC or another hub using the EIZO USB cable

(MD-C93).

GETTING THE MOST FROMYOUR MONITOR

•

When connecting the USB cable, check that the shape of the connector

at the USB cable side matches the shape at the

side.

connecting

Upstream connector

Upstream Port:

Connect the USB compliant

PC or another hub using the

EIZO USB cable (MD-C93).

(3) "EIZO USB Hub" appears on the screen. Insert the Windows 98 CD-

ROM and click "OK" in the "Insert Disk" window. Follow the

instruction of the window.

(4) After the setup of the USB Hub, "Add New Hardware Wizard"

window appears on the screen, and "Unknown Device" is detected.

(5) Click the "Next" button.

(6) Select the "Search for the best driver for your device (recommend)"

button, and click the "Next" button.

(7) Select the "Floppy disk drivers" and click the "Next" button.

(8) "EIZO USB Monitor" appears on the screen. Follow the instruction

of the window.

Once the above operation is completed, the monitor functions as a USB

hub and the USB compliant peripherals can be connected to the

downstream ports of the monitor.

•

Please refer to the readme.txt file for setup, too. Please make sure if the

proper installation is completed by following the confirmation below.

(Confirmation of USB Setup)

(1) Click the "Start" button and open the "Control Panel" from the

" Settings" .

(2) Select and double click the "System" from the "Control Panel" to

open the "System Properties".

(3) Confirm if the followings are in the "Device Manager" window:

"EIZO USB Hub" and "EIZO USB Monitor" appear under

"Universal serial bus controller".

The two points indicated that the settings were properly installed.

(For MacOS 8.5.1 or newer)

There is no need to install any software to utilize the USB hub function

when connecting a USB compliant PC (or another USB hub) with the USB

cable (MD-C93).

GETTING THE MOST FROMYOUR MONITOR

Connect the USB compliant peripherals to the downstream ports of

the monitor:

(Example of connection)

EIZO USB

Scanner

Cable

(MD-C93)

Printer

Monitor

Digital

Camera

Keyboard

Mouse

Front port (Example)

Rear port (Example)

Downstream ports:

Connect the cables from USB

compliant peripherals such as a

mouse, keyboard, etc.

Downstream connector

USB Specifications

USB standard

Rev. 1.0 complied self-powered hub

Downstream power supply 500 mA for each (Max.)

Communication speed

USB ports

12 Mbps (full), 1.5 Mbps (low)

Upstream port x 1

Downstream ports x 4

GETTING THE MOST FROMYOUR MONITOR

Troubleshooting

Problems

Points to check with possible solutions

1) • USB function

cannot be setup.

Check that the USB cable is correctly connected.

Check that the PC and OS is compliant to the

USB. (For the USB support of the system,

consult the manufacturer of each system.)

Check the PC’s BIOS setting for the USB. (For

details, refer to the manual of the PC.)

Check that the USB cable is correctly connected.

2) • PC is hung up.

Check the downstream ports by connecting the

peripherals to other downstream ports.

If the problem is solved by doing this, contact an

EIZO dealer.

•

The peripherals

connected to the

downstream

ports do not

operate.

Try executing the following method.

• Restarting the PC

• Connecting the PC and peripherals directly

If the problem is solved by doing this, contact an

EIZO dealer.

The power button of the APPLE keyboard does

not operate if it is connected to the EIZO USB

Hub. Please connect the keyboard directly to the

PC. Refer to the instruction of the PC for details.

ScreenManager Pro for USB (for Windows 98)

The utility software “ScreenManager Pro for USB” is included in the

enclosed utility disk. It is used for controlling the EIZO monitor from a

PC using a mouse or keyboard. It allows control of the screen adjustment

(size, position, distortion, color, contrast, moiré, etc.) from the familiar

OS environment. Also, the adjusted screen data and the color data can

be stored as the data files in the PC.

•

For information about ScreenManager Pro for USB setup, refer to the

readme file, too.

When using this program, the monitor must be connected to a USB

compliant PC (OS) or another hub with the EIZO USB cable

(enclosed). For instructions, please refer to the previous page.

To set up the “ScreenManager Pro for USB”, execute the “setup.exe”

program in the “apps” directory of the “EIZO Utility Disk” and follow

the procedure displayed on the screen. When the setup is completed, the

“EIZO” tab is added in the “Display Properties” window and the

monitor control function is available.

For details of the program, please refer to the Help menu in the program.

GETTING THE MOST FROMYOUR MONITOR

5 CLEANING

WARNING

•

Keep liquids away from the monitor.

Spillage into the cabinet may result in fire, electric shock, or

equipment damage.

If an object or liquid falls/spills into the cabinet, unplug the monitor

immediately. Have the unit checked by a qualified service engineer

before using it again.

Using the monitor in this condition could cause serious injury or

equipment damage.

CAUTION

•

To ensure safety, always unplug the monitor before cleaning it.

Failure to do so may result in electric shock.

Periodically clean the area around the plug.

Buildup of dust, water, or oil on the plug may result in fire.

Never use thinner, benzene, or other strong solvents or abrasive

cleaners, as these may cause damage to the cabinet or CRT.

Periodic cleaning is recommended to keep the monitor looking new and to

prolong its operational lifetime. Clean the cabinet and CRT areas as

follows.

Cabinet

To remove stains, wipe the cabinet with a soft, lightly moistened cloth

using a mild detergent. Do not spray wax or cleaner directly onto the

cabinet. Do not clean with compressed air.

CRT Surface

The monitor comes with a special cloth specifically designed to remove

fingerprints and dust from the screen. The cloth is washable, and will

remain effective regardless of the number of times it is washed. If the

supplied cloth is not available, you can clean the CRT surface with gauze,

cotton, or lens paper.

If necessary, stubborn stains can be removed by moistening part of a cloth

with water or alcohol (ethanol, methanol, or isopropyl alcohol) to enhance

its cleaning power.

CLEANING

6 SPECIFICATIONS

T68/TX·D7

Electrical Specifications

CRT

50 cm (19 inch) class, 90° deflection Aperture Grille type

CRT with Anti-Reflective SuperErgoCoat^®

0.25 mm (center), 0.27 mm (edges)

CRT AG Pitch

Scan Frequency

Horizontal:

Vertical:

30 kHz-96 kHz (Automatic)

50 Hz-160 Hz (Automatic)

Max. Active Display Area 362 mm (H) × 271 mm (V) (14.2” (Η) × 10.7” (V))

(Viewable image siz: 452 mm (17.7”))

* Display size can be set by the user through

microprocessor control panel.

* The actual size displayed can be dependent on the

graphics board or PC utilized.

Power Supply

100-120/220-240 VAC±10% , 50/60 Hz, 1.6/0.8 A

Power Consumption

Normal/Max:

120 W/155 W (with EIZO optional speaker & USB attached)

PowerManager Mode 1: Less than 10 W *

PowerManager Mode 2: Less than 3 W * (* When the USB hub is not connected)

Input Connector

Recommended Resolution

Input Signal

D-Sub mini 15-pin and BNC × 5 (switchable)

1280 dots × 1024 lines

Sync:

•

H/V Separate, TTL, Positive/Negative

H/V Composite, TTL, Positive/Negative

Sync on Green 0.3 Vp-p, Negative

Analog 0.7 Vp-p/75 Ω, Positive

Video:

Mechanical Specifications

Dimensions

452 mm (W) × 455 mm (H) × 478 mm (D)

(17.8” (W) × 17.9” (H) × 18.8” (D))

26.5 kg (58.4 lbs.)

Weight

USB Specifications

USB standard

Rev. 1.0 complied self-powered hub

Downstream power supply 500 mA for each (Max.)

Communication speed

USB ports

12 Mbps (full), 1.5 Mbps (low)

Upstream port x 1, Downstream ports x 4

Environmental Specifications

Temperature

operating: 0°C to 40°C (32 °F to 104 °F)

storage: -20°C to 60°C (-20 °F to 140 °F)

30% to 80% R.H. Non-condensing

Humidity

Certifications and Standards

100-120 VAC range

UL/CSA, FCC-B, DHHS, TÜV Rheinland/Ergonomics

Approved, TCO’99, EPA Energy Star^®Program

CE, CB, TÜV Rheinland/GS, TÜV Rheinland/Ergonomics

Approved, TCO’99, EPA Energy Star^®Program

220-240 VAC range

SPECIFICATIONS

F67/FX·D7

Electrical Specifications

CRT

50 cm (19 inch) class, 90° deflection FS type CRT with

Anti-Reflective SuperErgoCoat^®

0.26 mm

CRT Dot Pitch

Scan Frequency

Horizontal:

Vertical:

30 kHz-96 kHz (Automatic)

50 Hz-160 Hz (Automatic)

Max. Active Display Area 363 mm (H) × 272 mm (V) (14.2” (Η) × 10.7” (V))

(Diagonal: 453 mm (17.8”))

* Display size can be set by the user through

microprocessor control panel.

* The actual size displayed can be dependent on the

graphics board or PC utilized.

Power Supply

100-120/220-240 VAC±10% , 50/60 Hz, 1.6/0.8 A

Power Consumption

Normal/Max:

120 W/150 W (with EIZO optional speaker & USB attached)

PowerManager Mode 1: Less than 10 W *

PowerManager Mode 2: Less than 3 W * (* When the USB hub is not connected)

Input Connector

Recommended Resolution

nput Signal

D-Sub mini 15-pin and BNC × 5 (switchable)

1280 dots × 1024 lines

Sync:

•

H/V Separate, TTL, Positive/Negative

H/V Composite, TTL, Positive/Negative

Sync on Green 0.3 Vp-p, Negative

Analog 0.7 Vp-p/75 Ω, Positive

Video:

Mechanical Specifications

Dimensions

452 mm (W) × 455 mm (H) × 478 mm (D)

(17.8” (W) × 17.9” (H) × 18.8” (D))

24.0 kg (52.9 lbs.)

Weight

USB Specifications

USB standard

Rev. 1.0 complied self-powered hub

Downstream power supply 500 mA for each (Max.)

Communication speed

USB ports

12 Mbps (full), 1.5 Mbps (low)

Upstream port x 1, Downstream ports x 4

Environmental Specifications

Temperature

operating: 0°C to 40°C (32 °F to 104 °F)

storage: -20°C to 60°C (-20 °F to 140 °F)

30% to 80% R.H. Non-condensing

Humidity

Certifications and Standards

100-120 VAC range

UL/CSA, FCC-B, DHHS, TÜV Rheinland/Ergonomics

Approved, TCO’99, EPA Energy Star^®Program

CE, CB, TÜV Rheinland/GS, TÜV Rheinland/Ergonomics

Approved, TCO’99, EPA Energy Star^®Program

220-240 VAC range

SPECIFICATIONS

APPENDIX

Pin Assignment

Pin-Belegung

Affectation des Broches

D-Sub mini 15 pin connector

Pin No.

Signal

Red video

Green video

Blue video

Ground

Pin No.

Signal

No pin

Ground

(shorted)

Data

No pin

H. Sync

V. Sync

Clock

Red ground

Green ground

Blue ground

BNC connector

Connector

H.Sync

V. Sync

N/A

Green

Red

Blue

Input signal

Green

Composite

sync

Sync on green

N/A

Blue

TTL H/V

Composite sync

Separate sync

composite

N/A

Green

Red

sync

TTL

H. Sync

TTL

V. Sync

APPENDIX

Preset Timing

Vordefinierte Timing-Werte

Signaux prédéfinis

2 factory presets shown below have been registered in the monitor’s

microprocessor.

Der Monitor unterstützt 2 werkseitig vorgegebene Timing-Werte (siehe unten).

Diese Werte sind im Mikroprozessor Ihres Monitors gespeichert.

Les deux signaux ci-dessous ont été enregistrés en usine dans le microprocesseur du

moniteur.

Resolution

Frequencies

Interlace Sync Polarity Video Signal

Level

fH (kHz) fV (Hz)

VGA

(text)

720 x 400

31.47

70.09

Non

H/Negative 0.7V(p-p)/75Ω

V/Positive

VESA

1280 x 1024 91.15

85.02

Non

H/Positive

V/Positive

0.7V(p-p)/75Ω

Dimensions

Abmessungen

Dimensions

(inches)

350

(13.8)

452

(17.8)

362

(14.2)

10°

4°

271

(10.7)

455

(17.9)

478

(18.8)

47.5

(1.9)

45°

(3.0)

FRONT VIEW

SIDE VIEW

TOP VIEW

VORDERANSICHT

VUE DE FACE

SETENANSICHT

VUE DE CÔTÉ

DRAUFSICHT

VUE D'EN HAUT

APPENDIX

iii

Congratulations!

You have just purchased a TCO’99 approved and labelled product! Your choice has provided you

with a product developed for professional use. Your purchase has also contributed to reducing the

burden on the environment and also to the further development of environmentally adapted

electronics products.

Why do we have environmentally labelled computers?

In many countries, environmental labelling has become an established method for encourag-

ing the adaptation of goods and services to the environment. The main problem, as far as

computers and other electronics equipment are concerned, is that environmentally harmful

substances are used both in the products and during their manufacture. Since it is not so far

possible to satisfactorily recycle the majority of electronics equipment, most of these potentially

damaging substances sooner or later enter nature.

There are also other characteristics of a computer, such as energy consumption levels, that are

important from the viewpoints of both the work (internal) and natural (external) environments.

Since all methods of electricity generation have a negative effect on the environment (e.g. acidic

and climate-influencing emissions, radioactive waste), it is vital to save energy. Electronics

equipment in offices is often left running continuously and thereby consumes a lot of energy.

What does labelling involve?

This product meets the requirements for the TCO’99 scheme which provides for international

and environmental labelling of personal computers. The labelling scheme was developed as a

joint effort by the TCO (The Swedish Confederation of Professional Employees), Svenska

Naturskyddsforeningen (The Swedish Society for Nature Conservation) and Statens

Energimyndighet (The Swedish National Energy Administration).

Approval requirements cover a wide range of issues: environment, ergonomics, usability,

emission of electric and magnetic fields, energy consumption and electrical and fire safety.

The environmental demands impose restrictions on the presence and use of heavy metals,

brominated and chlorinated flame retardants, CFCs (freons) and chlorinated solvents, among

other things. The product must be prepared for recycling and the manufacturer is obliged to

have an environmental policy which must be adhered to in each country where the company

implements its operational policy.

The energy requirements include a demand that the computer and/or display, after a certain

period of inactivity, shall reduce its power consumption to a lower level in one or more stages.

The length of time to reactivate the computer shall be reasonable for the user.

Labelled products must meet strict environmental demands, for example, in respect of the

reduction of electric and magnetic fields, physical and visual ergonomics and good usability.

Below you will find a brief summary of the environmental requirements met by this product.

The complete environmental criteria document may be ordered from:

TCO Development

SE-114 94 Stockholm, Sweden

Fax: +46 8 782 92 07

Email (Internet): development@tco.se

Current information regarding TCO’99 approved and labelled products may also be

obtained via the Internet, using the address: http://www.tco-info.com/

Environmental requirements

Flame retardants

Flame retardants are present in printed circuit boards, cables, wires, casings and housings.

Their purpose is to prevent, or at least to delay the spread of fire. Up to 30% of the plastic in a

computer casing can consist of flame retardant substances. Most flame retardants contain

bromine or chloride, and those flame retardants are chemically related to another group of

environmental toxins, PCBs. Both the flame retardants containing bromine or chloride and the

PCBs are suspected of giving rise to severe health effects, including reproductive damage in fish-

eating birds and mammals, due to the bio-accumulative* processes. Flame retardants have been

found in human blood and researchers fear that disturbances in foetus development may occur.

The relevant TCO’99 demand requires that plastic components weighing more than 25 grams

must not contain flame retardants with organically bound bromine or chlorine. Flame

retardants are allowed in the printed circuit boards since no substitutes are available.

Cadmium**

Cadmium is present in rechargeable batteries and in the colour-generating layers of certain

computer displays. Cadmium damages the nervous system and is toxic in high doses. The

relevant TCO’99 requirement states that batteries, the colour-generating layers of display

screens and the electrical or electronics components must not contain any cadmium.

Mercury**

Mercury is sometimes found in batteries, relays and switches. It damages the nervous system

and is toxic in high doses. The relevant TCO’99 requirement states that batteries may not

contain any mercury. It also demands that mercury is not present in any of the electrical or

electronics components associated with the labelled unit.

CFCs (freons)

The relevant TCO’99 requirement states that neither CFCs nor HCFCs may be used during

the manufacture and assembly of the product. CFCs (freons) are sometimes used for washing

printed circuit boards. CFCs break down ozone and thereby damage the ozone layer in the

stratosphere, causing increased reception on earth of ultraviolet light with e.g. increased risks of

skin cancer (malignant melanoma) as a consequence.

Lead**

Lead can be found in picture tubes, display screens, solders and capacitors. Lead damages the

nervous system and in higher doses, causes lead poisoning. The relevant TCO’99 requirement

permits the inclusion of lead since no replacement has yet been developed.

For Europe, etc. (220-240 Vac) Only

CE Marking

Declaration of Conformity

Kind of equipment:

Type-designation:

Monitor

T68 (Model No. MA-1991), TX·D7 (Model No. MA-1991)

is in compliance with:

Council Directive 73/23/EEC

Council Directive 89/336/EEC

EN60950:1992+A1+A2+A3

EN55022 (classB):1995

EN61000-3-2:1995

EN50082-1:1992

EN61000-3-3:1995

Konformitätserklärung

Geräteart :

Gerätetyp :

Monitor

T68 (Modell-Nr. MA-1991), TX·D7 (Modell-Nr. MA-1991)

den folgenden Normen oder Vorschriften entspricht:

EU-Richtlinie 73/23/EEC

EU-Richtlinie 89/336/EEC

EN60950:1992+A1+A2+A3

EN55022 (classB):1995

EN61000-3-2:1995

EN50082-1:1992

EN61000-3-3:1995

Déclaration de conformité

Nature de l’équipement :

Type-désignation :

Moniteur

T68 (No. de modèle MA-1991), TX·D7 (Modell-Nr. MA-1991)

est en conformité avec :

Directive Européenne 73/23/EEC

Directive Européenne 89/336/EEC

EN60950:1992+A1+A2+A3

EN55022 (classB):1995

EN61000-3-2:1995

EN50082-1:1992

EN61000-3-3:1995

Hinweis zur Ergonomie :

Dieser Monitor erfüllt die Anforderungen an die Ergonomie nach ZH1/618/10.80 durch die

Ansteuerung mit der VGA - Videokarte, 1280 Punkte x 1024Zeilen, RGB analog, 0,7 Vp-p und

mindestens 85,0 Hz Bildwiederholfrequenz, non interlaced.

Weiterhin wird aus ergonomischen Gründen empfohlen, die Grundfarbe Blau nicht auf dunklem

Untergrund zu verwenden (schlechte Erkennbarkeit, Augenbelastung bei zu geringem Zeichenkontrast.)

PTB Note

Eigensichere Kathodestranlröhre nach Anlage III Röntgenverordnung. Die in diesem Geraet entstehende

Röntgenstrahlung ist durch die eigensichere Kathodenstrahlroehre ausreichend abgeschirmt.

Recycle Auskunft

Die Rücknahme dieses Produktes nach Nutzungsende übernimmt EIZO in Deutschland zusammen mit

dem Partner von Roll MBB Recycling GmbH.

Dort werden die Geräte in ihre Bestandteile zerlegt, die dann der Wiederverwertung zugeführt werden.

Um einen Abholtermin zu vereinbaren und die aktuellen Kosten zu erfahren, benutzen Sie bitte folgende

Rufnummber: 02153-73 35 00. Weitere Informationen finden Sie auch unter der Internet-Adresse:

www.eizo.de.

Hinweis

Die Bildroehre dieses Monitors is frei von Cadmium.

For Europe, etc. (220-240 Vac) Only

CE Marking

Declaration of Conformity

Kind of equipment:

Type-designation:

Monitor

F67 (Model No. MA-1990), FX·D7 (Model No. MA-1990)

is in compliance with:

Council Directive 73/23/EEC

Council Directive 89/336/EEC

EN60950:1992+A1+A2+A3

EN55022 (classB):1995

EN61000-3-2:1995

EN50082-1:1992

EN61000-3-3:1995

Konformitätserklärung

Geräteart :

Gerätetyp :

Monitor

F67 (Modell-Nr. MA-1990), FX·D7 (Modell-Nr. MA-1990)

den folgenden Normen oder Vorschriften entspricht:

EU-Richtlinie 73/23/EEC

EU-Richtlinie 89/336/EEC

EN60950:1992+A1+A2+A3

EN55022 (classB):1995

EN61000-3-2:1995

EN50082-1:1992

EN61000-3-3:1995

Déclaration de conformité

Nature de l’équipement :

Type-désignation :

Moniteur

F67 (No. de modèle MA-1990), FX·D7 (Modell-Nr. MA-1990)

est en conformité avec :

Directive Européenne 73/23/EEC

Directive Européenne 89/336/EEC

EN60950:1992+A1+A2+A3

EN55022 (classB):1995

EN61000-3-2:1995

EN50082-1:1992

EN61000-3-3:1995

Hinweis zur Ergonomie :

Dieser Monitor erfüllt die Anforderungen an die Ergonomie nach ZH1/618/10.80 durch die

Ansteuerung mit der VGA - Videokarte, 1280 Punkte x 1024 Zeilen, RGB analog, 0,7 Vp-p und

mindestens 85,0 Hz Bildwiederholfrequenz, non interlaced.

Weiterhin wird aus ergonomischen Gründen empfohlen, die Grundfarbe Blau nicht auf dunklem

Untergrund zu verwenden (schlechte Erkennbarkeit, Augenbelastung bei zu geringem Zeichenkontrast.)

PTB Note

Eigensichere Kathodestranlröhre nach Anlage III Röntgenverordnung. Die in diesem Geraet entstehende

Röntgenstrahlung ist durch die eigensichere Kathodenstrahlroehre ausreichend abgeschirmt.

Recycle Auskunft

Die Rücknahme dieses Produktes nach Nutzungsende übernimmt EIZO in Deutschland zusammen mit

dem Partner von Roll MBB Recycling GmbH.

Dort werden die Geräte in ihre Bestandteile zerlegt, die dann der Wiederverwertung zugeführt werden.

Um einen Abholtermin zu vereinbaren und die aktuellen Kosten zu erfahren, benutzen Sie bitte folgende

Rufnummber: 02153-73 35 00. Weitere Informationen finden Sie auch unter der Internet-Adresse:

www.eizo.de.

Hinweis

Die Bildroehre dieses Monitors is frei von Cadmium.

For U.S.A, Canada, etc. (rated 100-120 Vac) Only

FCC Declaration of conformity

We, the Responsible Party

EIZO Nanao Technologies Inc.

5710 Warland Drive, Cypress, CA 90630

Phone: (562) 431-5011

declare that the product

Trade name: EIZO

Model: FlexScan FX·D7/Model No: MA-1990

Model: FlexScan TX·D7/Model No: MA-1991

is in conformity with Part 15 of the FCC Rules. Operation of this product is subject to

the following two conditions: (1) this device may not cause harmful interference, and (2)

this device must accept any interference received, including interference that may cause

undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to Part 15 of the FCC Rules. These limits are designed to provided

reasonable protection against harmful interference in a residential installation. This

equipment generates, uses, and can radiate radio frequency energy and, if not installed and

used in accordance with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equipment off and on, the user

is encouraged to try to correct the interference by one or more of the following measures.

*Reorient or relocate the receiving antenna.

*Increase the separation between the equipment and receiver.

*Connect the equipment into an outlet on a circuit different from that to which the receiver

is connected.

*Consult the dealer or an experienced radio/TV technician for help.

Changes or modifications not expressly approved by the party responsible for compliance

could void the user’s authority to operate the equipment.

Note

Use the attached specified shielded cable below or EIZO signal cable with this monitor so

as to keep interference within the limits of a Class B digital device.

-AC Cord

-Signal Cable (D-SUB mini 15 pin - D-SUB mini 15 pin, MD-C87)

Canadian Notice

This Class B digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de le classe B est comforme à la norme NMB-003 du Canada.

Emerson HK250 User Manual
Electrolux U20326 SIG 515 User Manual
Cypress enCoRe CY7C64345 User Manual
Cuisinart Convection Oven Cuisinart User Manual
Cres Cor Convection Oven CO151FWUA12B Q1 User Manual
AT T E5926 User Manual
Asus Computer Monitor VW193 User Manual
ASRock Computer Hardware VERISON 1 2 User Manual
Apple 150B User Manual
AOC 193P 19 User Manual