User’s Manual
Color LCD Monitor
English
TABLE OF CONTENTS
PRECAUTIONS......................................................................................4
1. INTRODUCTION ....................................................................................9
1-1. Features .......................................................................................................9
1-2. Package Contents.........................................................................................9
1-3. Controls & Connectors .............................................................................10
2. CABLE CONNECTION ........................................................................12
2-1. Before Connecting .....................................................................................12
2-2. Connecting the Signal Cable......................................................................13
2-3. Connecting Two PCs to the Monitor.........................................................15
3. ScreenManager...................................................................................17
3-1. How to use the ScreenManager .................................................................17
3-2. ScreenManager Adjustments and Settings..................................................18
3-3. Useful Functions ........................................................................................19
4. ADJUSTMENT .....................................................................................21
4-1. Screen Adjustment .....................................................................................21
4-2. Displaying a Low Resolutions ...................................................................25
4-3. Color Adjustment ......................................................................................27
4-4. Power-save Setup .......................................................................................29
5. ActiveShot Function...........................................................................31
5-1. Operation ..................................................................................................31
5-2. Sub Window Settings.................................................................................32
5-3. Settings using the Control Buttons.............................................................34
6. ActiveRotation Function ....................................................................35
7. Recommended Functions..................................................................37
8. ATTACHING AN ARM ..........................................................................38
9. TROUBLESHOOTING..........................................................................40
10. CLEANING.........................................................................................44
11. SPECIFICATIONS..............................................................................45
12. GLOSSARY........................................................................................48
APPENDIX/ANHANG/ANNEXE ..................................................................i
TABLE OF CONTENTS
3
English
PRECAUTIONS
IMPORTANT!
• This product has been adjusted specifically for use in the region to which it was
originally shipped. If operated outside the region to which it was originally shipped,
the product may not perform as stated in the specifications.
• To ensure personal safety and proper maintenance, please read this section and the
caution statements on the unit (refer to the figure below).
[Location of the Caution Statements]
WARNING
If the unit begins to emit smoke, smells like something is burning, or
makes strange noises, disconnect all power connections immediately
and contact your dealer for advice.
Attempting to use a malfunctioning unit may result in fire, electric shock, or
equipment damage.
Do not open the cabinet or modify the unit.
Opening the cabinet or modifying the unit may result in fire, electric shock, or
burn.
Refer all servicing to qualified service personnel.
Do not attempt to service this product yourself as opening or removing covers
may result in fire, electric shock, or equipment damage.
4
PRECAUTIONS
English
WARNING
Keep small objects or liquids away from the unit.
Small objects accidentally falling through the ventilation slots into the cabinet
or spillage into the cabinet may result in fire, electric shock, or equipment
damage.
If an object or liquid falls/spills into the cabinet, unplug the unit immediately.
Have the unit checked by a qualified service engineer before using it again.
Place the unit at the strong and stable place.
A unit placed on an inadequate surface may fall and result in injury or
equipment damage.
If the unit falls, disconnect the power immediately and ask your dealer for
advice. Do not continue using a damaged unit. Using a damaged unit may
result in fire or electric shock.
OK
Set the unit in an appropriate location.
Not doing so may result in fire, electric shock, or equipment damage.
* Do not place outdoors.
* Do not place in the transportation system (ship, aircraft, trains, automobiles,
etc.)
* Do not place in a dusty or humid environment.
* Do not place in a location where the steam comes directly on the screen.
* Do not place near heat generating devices or a humidifier.
To avoid danger of suffocation, keep the plastic packing bags away
from babies and children.
Use the enclosed power cord and connect to the standard power outlet
of your country.
Be sure to remain within the rated voltage of the power cord.
Not doing so may result in fire or electric shock.
To disconnect the power cord, grasp the plug firmly and pull.
Tugging on the cord may damage and result in fire or electric shock.
OK
PRECAUTIONS
5
English
WARNING
The equipment must be connected to a grounded main outlet.
Not doing so may result in fire or electric shock.
Use the correct voltage.
* The unit is designed for use with a specific voltage only. Connection to
another voltage than specified in this User’s Manual may cause fire, electric
shock, or equipment damage.
* Do not overload your power circuit, as this may result in fire or electric
shock.
Handle the power cord with care.
* Do not place the cord underneath the unit or other heavy objects.
* Do not pull on or tie the cord.
If the power cord becomes damaged, stop using it. Use of a damaged cord
may result in fire or electric shock.
Never touch the plug and power cord if it begins to thunder.
Touching them may result in electric shock.
When attaching an arm stand, please refer to the user’s manual of the
arm stand and install the unit securely with the enclosed screws.
Not doing so may cause the unit to become unattached, which may result in
injury or equipment damage. When the unit is dropped, please ask your dealer
for advice. Do not continue using a damaged unit. Using a damaged unit may
result in fire or electric shock. When reattaching the tilt stand, please use the
same screws and tighten them securely.
Do not touch a damaged LCD panel directly with bare hands.
The liquid crystal that may leak from the panel is poisonous if it enters the
eyes or mouth.
If any part of the skin or body comes in direct contact with the panel, please
wash thoroughly. If some physical symptoms result, please consult your
doctor.
Follow local regulation or laws for safe disposal.
The backlight of the LCD panel contains mercury.
6
PRECAUTIONS
English
CAUTION
Handle with care when carrying the unit.
Disconnect the power cord and cables when moving the unit. Moving the unit
with the cord attached is dangerous. It may result in injury.
When handling the unit, grip the bottom of the unit firmly with both
hands ensuring the panel faces outward before lifting.
Dropping the unit may result in injury or equipment damage.
OK
Do not block the ventilation slots on the cabinet.
* Do not place any objects on the ventilation slots.
* Do not install the unit in a closed space.
* Do not use the unit laid down or upside down.
Blocking the ventilation slots prevents proper airflow and may result in fire,
electric shock, or equipment damage.
Do not touch the plug with wet hands.
Doing so may result in electrical shock.
Use an easily accessible power outlet.
This will ensure that you can disconnect the power quickly in case of a
problem.
Periodically clean the area around the plug.
Dust, water, or oil on the plug may result in fire.
Unplug the unit before cleaning it.
Cleaning the unit while it is plugged into a power outlet may result in electric
shock.
If you plan to leave the unit unused for an extended period, disconnect
the power cord from the wall socket after turning off the power switch
for the safety and the power conservation.
PRECAUTIONS
7
English
LCD Panel
In order to suppress the luminosity change by long-term use and to maintain
the stable luminosity, use of a monitor in lower brightness is recommended.
The screen may have defective pixels. These pixels may appear as slightly light
or dark area on the screen. This is due to the characteristics of the panel itself,
and not the product.
The backlight of the LCD panel has a fixed life span. When the screen becomes
dark or begins to flicker, please contact your dealer.
Do not press on the panel or edge of the frame strongly, as this may result in
damage to the screen. There will be prints left on the screen if the pressed
image is dark or black. If pressure is repeatedly applied to the screen, it may
deteriorate or damage your LCD panel. Leave the screen white to decrease the
prints.
Do not scratch or press on the panel with any sharp objects, such as a pencil or
pen as this may result in damage to the panel. Do not attempt to brush with
tissues as this may scratch the LCD panel.
8
PRECAUTIONS
English
1. INTRODUCTION
Thank you very much for choosing an EIZO Color Monitor.
1-1. Features
• Dual inputs compliant
• DVI (p. 48) Digital input (TMDS (p. 49)) compliant
• [Horizontal scanning frequency] Analog: 30 - 82 kHz, Digital: 30 - 81 kHz
[Vertical scanning frequency] Analog: 49 - 86 Hz (1280 x 1024 ~ 76 Hz)
Digital: 59 - 61 Hz (VGA text: 70 Hz)
[Resolution] 1280 dots x 1024 lines
• ActiveShot (Picture in Picture) function incorporated (p. 31)
• ActiveRotation (changing the display orientation to portrait) function incorporated
(p. 35)
• Smoothing function incorporated for the adjustment of an enlarged image (p. 26)
• Auto Adjustment compliant and original “Picture Adjustment Program” software
included
• ColorManagement function incorporated (p. 27)
• Support to sRGB (p. 49) standard
• The height adjustable stand incorporated
• Ultra slim bezel incorporated
1-2. Package Contents
Please contact your local dealer for assistance if any of the listed items are missing or
damaged.
• LCD Monitor
• EIZO LCD Utility Disk
• User’s Manual
• Power Cord
• Signal Cable (FD-C16)
• Signal Cable (MD-C100)
• EIZO USB Cable (MD-C93)
• Quick Reference
• LIMITED WARRANTY
NOTE
• Please retain the packing materials for future transference.
• The EIZO USB cable is used when using the software, “ActiveRotation” application
(for Windows) in the EIZO LCD Utility Disk. (Refer to the readme.txt in the EIZO LCD
Utility Disk for the details.)
1. INTRODUCTION
9
English
1-3. Controls & Connectors
Front
(2)
(1)
Control Panel
SIGNAL
1 - 2
AUTO
ENTER
(3)
(7)
(4)
(6)
(9)
(8)
(5)
(1) ScreenManager®
(2) Main Power Button
(3) Input Signal Selection Button
(4) PinP (Picture in Picture) Button
(5) Auto Adjustment Button
(6) Enter Button
(7) Control Buttons (Left, Down, Up, Right)*1
(8) Power Button
(9) Power Indicator*2
Blue
Operation
Yellow
Power saving
Flashing yellow (2 times for each)
Flashing yellow slowly
Off
Power save mode Digital only
Power is off (Main power is on)
Power off
*1 These buttons are changed to Up, Left, Right, Down in case of selecting
“Portrait(HW/SW)” for <Orientation> of ScreenManager <Others> (p. 35)
*2 Regarding the power indicator for the off timer, see p. 19.
10 1. INTRODUCTION
English
Rear
(10)
(12)
(11)
Bottom
(13) (14) (15)
(16)
(10) Height Adjustable Stand (Detachable)*3
(11) Power Terminal Covers for the Optional peripheral
(12) Security Lock Slot*4
(13) D-Sub mini 15 pin Input Connector (SIGNAL 1)
(14) DVI-I Input Connector (SIGNAL 2)
(15) USB Port (1 Upstream)*5
(16) Power Connector
*3
The LCD monitor has the capability of the Portrait/Landscape display. (The panel
pivots in the clockwise direction 90°), see p. 35.
The LCD monitor can be used with an optional arm by removing the stand, see p.
38.
*4
Allows for connection of a security cable. This lock supports Kensington’s
MicroSaver security system. For further information, please consult’
Kensington Technology Group
2855 Campus Drive, San Mateo, CA 94403 USA
Tel.: 800-650-4242, x3348, Intl: 650-572-2700, x3348
Fax: 650-572-9675
*5
USB upstream port is used when using the “ActiveRotation” application (for
Windows) in the EIZO LCD Utility Disk (refer to the Readme file).
1. INTRODUCTION 11
English
2. CABLE CONNECTION
2-1. Before Connecting
Before connecting your monitor to the PC, change the display screen settings (resolution
p. 49) and frequency) in accordance with the charts below.
NOTE
• When your computer and display support VESA DDC, the suitable resolution and
the refresh rate are set by just plugging your display into the computer without any
manual settings.
Analog Input
Resolution
Frequency
~ 85 Hz
67 Hz
Dot Clock
Remarks
VGA, VESA
Apple Macintosh
VGA TEXT
VESA
640 × 480
140 MHz
(Max.)
640 × 480
720 × 400
70 Hz
800 × 600
~ 85 Hz
75 Hz
832 × 624
Apple Macintosh
VESA
1024 × 768
1152 × 864
1152 × 870
1152 × 900
1280 × 960
1280 × 960
1280 × 1024
1280 × 1024
~ 85 Hz
75 Hz
VESA
75 Hz
Apple Macintosh
SUN WS
~ 76 Hz
60 Hz
VESA
75 Hz
Apple Macintosh
SUN WS
67 Hz
~ 75 Hz
VESA
Digital Input
Only the following resolutions with frequency can be displayed on this model.
Resolution
640 × 480
Frequency
60 Hz
Dot Clock
Remarks
VGA
120 MHz
(Max.)
720 × 400
70 Hz
VGA TEXT
VESA
800 × 600
60 Hz
1024 × 768
1280 × 1024
60 Hz
VESA
60 Hz
VESA
12 2. CABLE CONNECTION
English
2-2. Connecting the Signal Cable
NOTE
• Be sure that the Power buttons of both the PC and the monitor are OFF.
1. Plug the signal cable into the connector at the rear of the monitor
and the other end of the cable into the video connector on the PC.
After connecting, secure the connection with the screw-in fasteners.
Analog Input
D-Sub mini 15 pin
DVI
MD-C100
Power Cord
FD-C16
Signal Cable
Connector of PC
PC
FD-C16 or MD-C100
enclosed
Video Output
Connector D-Sub mini
15 pin
• Standard graphics card
• Macintosh G3 (Blue &
White) / Power Mac G4
(VGA)
FD-C16 or MD-C100
enclosed + Adapter*
Video Output
Connector D-Sub 15
pin
• Macintosh
*Macintosh Adapter (Optional)
Digital Input
DVI
FD-C39 (Optional)
Signal Cable Connector of PC
Power Cord
PC
FD-C39
(Optional)
Video Output
Connector DVI
• Power Mac G4 (DVI)
• Digital graphics board
NOTE
• The monitor is not compatible with a Power Mac G4/G4 Cube ADC (Apple
Display Connector)
2. CABLE CONNECTION 13
English
2. Plug the power cord into the power connector on the rear of the
monitor.
3. Lead the power cord and signal cable into the cable holder at rear of
the monitor.
NOTE
• The cables are recommended to lead with slight sag for the smooth motion of
the stand and the Portrait/Landscape display.
Cable Holder
4. Plug the other end of the power cord into a power outlet.
WARNING
Use the enclosed power cord and connect to the standard
power outlet of your country.
Be sure to remain within the rated voltage of the power cord.
Not doing so may result in fire or electric shock.
The equipment must be connected to a grounded main
outlet.
Not doing so may result in fire or electric shock.
14 2. CABLE CONNECTION
English
5. Turn on the monitor's main power and then switch on the PC's
power.
The monitor’s power indicator will light up (blue).
If an image does not appear, refer to the “TROUBLESHOOTING” (p. 40) for
advice.
Whenever finished, turn off the PC and the monitor.
6. When using the monitor in portrait style, refer to the “6.
ActiveRotation Function” (p. 35).
NOTE
• When turning on the monitor, the kind of the input signal (Signal1/ Analog or Signal
2/Analog or Digital) is displayed for a few seconds on the right top corner of the
screen.
• Adjust brightness of the screen depending on the brightness of your environment.
• Be sure to take adequate rests. A 10-minute rest period each hour is suggested.
2-3. Connecting Two PCs to the Monitor
Two PCs can be connected to the monitor through the Signal 1 and the Signal 2 on the
back of the monitor.
Connecting Examples
Signal 2
Signal 1
PC 1
PC 2
(Ex.1) Analog D-Sub Signal Cable
mini 15
Signal Cable
D-Sub Analog
mini
15 pin
(MD-C100 enclosed)
(FD-C16 enclosed)
pin
(Ex.2) Analog D-Sub Signal Cable
mini 15
Signal Cable
DVI
Digital
(MD-C100 enclosed)
(FD-C39 Optional)
pin
2. CABLE CONNECTION 15
English
Selecting the Active Input
The Input signal selection button on the control panel can be used to select either Signal
1 or Signal 2 as the active input at any time. Every time the button is pressed, the input
changes. When switching the signal, the kind of the input signal (Signal1/ Analog or
Signal 2/Analog or Digital) is displayed for a few seconds on the right top corner of the
screen.
Input Signal Selection Button
SIGNAL
1 - 2
AUTO
ENTER
NOTE
• When using the ActiveShot function (p. 31), pressing the Input signal selection
button switches the image of the Main window and the Sub window.
The Priority Input Signal
This function is used to select which PC will have priority to control the monitor when
utilizing two PCs. The monitor constantly checks the input signals and switches
automatically in accordance with the “Input Priority” setting (see table below). Once a
priority is set, whenever a change of signal is detected at the selected input, the monitor
will switch the input to that signal.
In the case of only one signal being present at either input, the monitor automatically
detects and displays that signal.
Priority
Setting
Performance
If signals from both inputs are present, the monitor gives preference to Signal
1 in the following cases.
Signal 1
• When the power of the monitor is turned ON
• When the signal input to Signal 1 is changed even if active input was Signal
2.
If signals from both inputs are present, the monitor gives preference to Signal
2 in the following cases.
Signal 2
Manual
• When the power of the monitor is turned ON
• When the signal input to Signal 2 is changed even if active input was Signal
1.
The monitor will not detect signals automatically in this mode. Select the
active input by pressing the input signal selection button on the monitor’s
control panel.
NOTE
• About Power saving mode
When the Signal 1 or Signal 2 is selected, the power saving mode of the monitor
operates only if both PCs are in power saving mode.
16 2. CABLE CONNECTION
English
3. ScreenManager
3-1. How to use the ScreenManager
Control Buttons
Left, Down, Up, Right
SIGNAL
1 - 2
AUTO
ENTER
Auto Adjustment
button
Enter button
1. Entering the ScreenManager
Press the Enter button once to display the main menu of the ScreenManager.
[Main Menu]
2. Making Adjustments and Settings
(1) Select the desired sub menu icon using the Control buttons and press the Enter
button. The sub menu appears.
(2) Use the Control buttons to select the desired setting icon and press the Enter
button. The setting menu appears.
(3) Use the Control buttons to make all required adjustments and press the Enter
button to save the settings.
3. Exiting the ScreenManager
(1) To return to the main menu, select the <Return> icon or press the down button
twice, followed by the Enter button.
(2) To exit the ScreenManageru, select the <Exit> icon or press the down button
twice, followed by the Enter button.
NOTE
• Double clicking the Enter button at any time also exits the ScreenManager menu.
3. ScreenManager 17
English
3-2. ScreenManager Adjustments and Settings.
The following table shows all the ScreenManager’s adjustment and setting menus.
“*” indicates adjustments of analog input only and “**” indicates digital input only.
Main menu
Sub menu
Reference
*
*
Screen
Clock
4-1. Screen Adjustment (p. 21)
Phase
Position
Resolution
*
*
Range Adjustment
Smoothing
Signal Filter
ColorManagement
Color Mode
4-3. Color Adjustment (p. 27)
Custom
Mode
Brightness/
Contrast
Temperature
Saturation
Hue
Gain
Reset
sRGB
Brightness
Picture in Picture
PowerManager
Standard
Clip
5. ActiveShot Function (p. 31)
4-4. Power-save Setup (p. 29)
**
*
DVI DMPM
VESA DPMS
EIZO MPMS
Screen Size
*
Others
4-2. Displaying a Low Resolutions (p. 25)
Select the priority input signal. (p. 16)
Border Intensity
Input Priority
Off Timer
Set the monitor’s off timer to on or off. (p.
19)
Beep
Set the monitor’s beeper to on or off. (p.
46)
Menu
Settings
Menu Size
Change the size of the menu.
Adjust the menu position
Menu Position
Menu Off Timer
Translucent
Set the menu displaying time.
Set the transparency of the background.
6. ActiveRotation Function (p. 35)
Orientation
Power Indicator
Make non-light for blue lighting when the
screen is displayed.
Reset
Return to the factory default settings. (p.
46)
Information
Language
Information
Review the ScreenManager’s settings,
model name, serial number and usage
time*1.
English, German, French,
Spanish, Italian, Swedish and
Japanese
Select the ScreenManager’s language.
*1Due to the inspection on the factory, the usage time may not “0 hour” at shipping.
18 3. ScreenManager
English
3-3. Useful Functions
Adjustment Lock
Use the “Adjustment Lock” function to prevent any accidental changes.
Locked function
• Auto adjustment button adjustments and settings in the
ScreenManager.
• Auto Adjustment Button
• PinP Button
Unlocked function
• Adjustment of contrast and brightness by the control buttons.
• Input Signal Selection Button
[To lock]
(1) Switch off the monitor’s power by the power button on the control panel.
(2) Press on the Auto adjustment button while switching on the monitor’s power.
[To unlock]
(1) Switch off the monitor’s power by the power button on the control panel.
(2) Hold down the Auto adjustment button once again and turn the power back on.
Off Timer
The off timer function causes the monitor to automatically enter a power off state after
a predetermined amount of time has lapsed. This function was created to reduce
afterimage (p. 48) characteristics that are particular to LCD monitors when the monitor
screen is left on for a long period without use.
[Procedure]
(1) Select <Off Timer> in the ScreenManager “Others” menu.
(2) Select “Enable” and press the right and left buttons to adjust the “On Period” (1 to
23 hours).
[Off timer system]
PC
Monitor
Power Indicator
On Period (1H - 23H)
Last 15 min. in "On period"
"On period" expired
Operation
Blue
Advance Notice *1
Blue Flashing
Power off
Flashing yellow slowly
*1Advance notice (Power indicator flashing blue) will be given 15 minutes before the monitor
automatically enters the “Power Off” mode. To delay entering the “Power Off” mode, press the
power button during the advance notice period. The monitor will continue to operate for an
additional 90 minutes.
[Power Resumption Procedure]
Press the power button to return to a normal screen.
NOTE
• The off timer function works while the PowerManager is active, but there is no
advance notice before the monitor’s power is switched off.
3. ScreenManager 19
English
EIZO Logo Appearing Function
When switching on the power button on the control panel, the EIZO logo is displayed
for a while. If you desire to display or undisplay this logo, use this function. (Default is
logo appearing.)
[To undisplay]
(1) Switch off the monitor’s power by the Power button on the control panel.
(2) Hold down the Enter button once again and turn the power back on.
[To display again]
(1) Switch off the monitor’s power by the Power button.
(2) Hold down the Enter button once again and turn the power back on.
20 3. ScreenManager
English
4. ADJUSTMENT
4-1. Screen Adjustment
NOTE
• Allow the LCD monitor to stabilize for at least 20 minutes before making image
adjustments.
• When using the ActiveShot function (p. 31), adjust the screen of each signal in
advance.
When connecting the DVI cable for digital input, see p. 24.
Analog Input
Screen adjustments for the LCD monitor should be used in suppressing screen flickering
and also for adjusting the screen to its proper position. There is only one correct
position for each display mode. It is also recommended to use the ScreenManager
function when first installing the display or whenever changing the system. For
convenience, an easy set-up Program installed on the utility disk to assist in the set-up
procedure is provided.
Adjustment Procedure
1. Press the Auto adjustment button on the control panel.
The message “Your setting will be lost, if you press again now.” appears and
remains on the screen for 5 seconds. While the message is on the screen, press the
Auto adjustment button again to automatically adjust the clock, phase, screen
position and resolution. If you do not wish to do adjust the screen, do not press
the Auto adjustment button again.
NOTE
• The Auto sizing function is intended for use on the Macintosh and on
AT-compatible PC running Windows. It may not work properly in either of the
following cases.
When running an AT-compatible PC on MS-DOS (Not windows). The
background color for the “wall paper” or “desktop” pattern is set to black.
If the appropriate screen cannot be made by using the Auto adjustment
button, adjust the screen through the following procedures. If the
appropriate screen can be made, proceed to step 4.
2. Install the “Screen adjustment program”
Having read the “Readme.txt” file, install and run the “Screen adjustment
program” in the enclosed EIZO LCD utility disk. Step by step adjustment is
provided by the wizard guide. (If using the Windows, the program can be directly
run from the menu screen of the EIZO LCD utility disk.)
4. ADJUSTMENT 21
English
NOTE
• If the user’s operating system has no utility disk (e.g. OS/2), we recommend
setting the desktop pattern to that as shown in the diagram on the following
page.
3. Adjust by using <Screen> menu in the ScreenManager.
(1) Vertical bars appear on the screen
→
Use the <Clock> (p. 48) adjustment.
Select the “Clock” and eliminate the vertical bars by using the right and left of
the control buttons. Do not continuously press the control buttons, as the
adjustment value will change quickly and make it difficult to locate the most
suitable adjustment point.
If the horizontal flickering, blur or bars appear, proceed to “Phase” adjustment
as follows.
NOTE
• When adjusting the <Clock>, the horizontal screen size will also change.
(2) Horizontal flickering, blurring or bars appear on the screen.
→
Use the <Phase> (p. 48) adjustment.
Select the <Phase> and eliminate the horizontal flickering, blurring or bars by
using the right and left buttons.
NOTE
• Horizontal bars may not completely disappear from the screen depending on
the PC.
22 4. ADJUSTMENT
English
(3) The screen position is not incorrect.
Use the <Position> adjustment.
→
The correct displayed position of the monitor is decided because the number
and the position of the pixels are fixed. The <Position> adjustment moves the
image to the correct position.
Select <Position> and adjust the position by using the Up, Down, Right and
Left buttons.
If vertical bars of distortion appear after finishing the <Position> adjustment,
return to <Clock> adjustment and repeat the previously explained adjustment
procedure (“Clock” → “Phase” → “Position”)
(4) Screen image is smaller or larger than the actual screen images.
→
Use the <Resolution> adjustment.
Adjustment is needed when the input signal resolution and the resolution now
being displayed are different.
Select <Resolution> and confirm if the resolution now being displayed is the
same as the input resolution. If it is not, adjust the vertical resolution using the
up and down button and adjust the horizontal resolution using the right and
left buttons.
Smaller than the actual screen images.
Adjusted to actual screen
Larger than the actual screen images.
4. ADJUSTMENT 23
English
4. Adjust the output signal range (Dynamic Range) of the signal.
Use the <Range Adjustment> (p. 49).
→
This controls the level of output signal range to display the whole color gradation
(256 colors).
[Procedure 1]
Press the Auto adjustment button on the control panel while displaying the <Range
Adjustment> menu to automatically adjust the range. The screen blanks for a
moment, and adjusts the color range to display the whole color gradation of the
current output signal.
[Procedure 2]
Pressing Auto adjustment button while displaying the contrast/brightness
adjustment screen (appeared by pressing the control buttons directly) adjusts the
range automatically. (Contrast and Brightness will not be adjusted.)
Digital Input
The monitor displays the digital input image correctly based on its pre-setting data.
However, if the image position is not correct or larger than the actual image screen,
please adjust the following adjustment items using the “Screen” menu of the
ScreenManager.
1. The screen position is incorrect.
→
Use the <Position> adjustment.
See p. 23.
2. Screen image is smaller or larger than the actual screen images.
→
Use the <Resolution> adjustment.
See p. 23.
24 4. ADJUSTMENT
English
4-2. Displaying a Low Resolutions
The lower resolutions are enlarged to full screen automatically. Using the <Screen Size>
function in the <Others> menu enables to change the screen size.
1. Change the screen size when displaying a low resolution.
→
Select the <Screen Size>.
Select the <Screen Size> in the <Others> menu and select the screen size by using
the up and down buttons.
Menu
Function
Displays the picture on the screen in full, irrespective of the picture’s
resolution. Since the vertical resolution and the horizontal resolution
are enlarged at different rates, some images may appear distorted.
Full
Displays the picture on the screen in full, irrespective of the picture’s
resolution. Since the vertical resolution and horizontal resolution are
enlarged at same rates, some horizontal or vertical image may
disappear.
Enlarged
Normal
Displays the picture at the actual Screen resolution.
Example: Displaying1024 x 768
Full
Normal
Enlarged
(Default)
(1024×768)
(1280×1024)
(1280×960)
NOTE
• When using the ActiveShot (p. 31) or ActiveRotation (p. 35) function, the
screen size cannot be enlarged.
• When displaying the Sub window of ActiveShot function after setting “Enlarged”
or “Normal”, the screen image of the Main window is displayed in “Full“ mode.
4. ADJUSTMENT 25
English
2. Smooth the blurred texts of the enlarged screen.
Switch the <Smoothing> setting.
→
Select the suitable level from 1 – 5 (Soft – Sharp).
Select <Smoothing> in the <Screen> menu and adjust by using the right and left
buttons.
NOTE
• <Smoothing> is disabled when the screen is displayed in the following
resolutions.
*1280 x 1024
*The image size is doubled both in horizontally and vertically to (i.e. 1280 x 960
enlarged from 640 x 480) provide clear focus which does not require this
function.
3. Set the brightness of the black area surrounding the displayed image.
→
Set the <Border Intensity>.
In the <Enlarge> mode or <Full Screen> mode, the outer area (border) is usually
black.
Select <Border Intensity> in the <Others> menu and adjust by using the right and
left buttons.
Border
26 4. ADJUSTMENT
English
4-3. Color Adjustment
The <ColorManagement> menu in the ScreenManager enables to change the color of
the screen. By using the <Color Mode>, the adjustment mode can be selected from
<Custom mode> (to adjust the color settings according to your preference) and <sRGB>
mode.
In the analog input, perform the “Range Adjustment” (p. 24) before making the
color adjustments.
NOTE
• Allow the LCD monitor to stabilize for at least 20 minutes before making image
adjustments. (Allow the monitor to warm up for at least 20 minutes before making
adjustments.)
• Performing the <Reset> of the <ColorManagement> menu returns the color settings
to the default settings. The values shown in percentages represent the current level
within the specific adjustment. They are available only as a reference tool. (To
create a uniform white or black screen, the percentages for each will probably not be
the same.)
<Custom> mode:To adjust the color settings according
to your preference
To set the Brightness of the screen
→
Use the <Brightness> adjustment.
The brightness of the entire screen is controlled by changing the brightness of the
backlight.
Select <Brightness> in the screen menu and adjust by using the right and left
buttons.
NOTE
• Directly pressing the control buttons also adjusts the contrast and brightness.
Press the <Enter> button to save and exit the settings after the adjustment.
To set the Contrast of the screen
→
Use the <Brightness> adjustment.
This controls the brightness for the each color (red, blue and green) at the same
time.
Select <Brightness> in the screen menu and adjust by using the right and left
buttons.
NOTE
• Percentage except 100 % may cause undisplayable color tone.
4. ADJUSTMENT 27
English
To set the color temperature (p. 49)
→
Set the <Temperature>.
The <Temperature> can be set from 4,000 K to 10,000 K, in 500 K increments
(including 9,300 K). Default setting is off (normal white).
NOTE
• The values shown in the Kelvin are available only as a reference tool.
• Setting the temperature under 4,000 K or over 10,000 K invalidates the color
temperature setting. (The color temperature’s setting turns “OFF”.)
To change the saturation
→
Use the <Saturation> adjustment.
The <Saturation> can be selected from -16 ~ 16. Setting the minimum level (-16)
turns the image to the monochrome.
NOTE
• The <Saturation> adjustment may cause undisplayable color tone.
To change the flesh color, etc.
→
Use the <Hue> adjustment.
The <Hue> can be selected from –20 to 20.
NOTE
• The <Hue> adjustment may cause undisplayable color tone.
To change each color (red, green and blue)
→
Use the <Gain> (p. 48) adjustment
By adjusting the red, green and blue color tones for each mode, custom colors can
be defined. The 100 % indicates unadjusted condition. Display a white or gray
background image and adjust the <Gain>.
NOTE
• The values shown in the percentage are available only as a reference tool.
• Setting the <Temperature> (p. 28) invalidates the <Gain> adjustment. <Gain>
setting returns to the default: All the color indicates 100 %.
<sRGB> mode:To select <sRGB> mode
→ Select <sRGB>.
To set the Brightness of the screen
→
Use the <Brightness> adjustment.
See p. 27.
28 4. ADJUSTMENT
English
4-4. Power-save Setup
The <PowerManager> menu in the ScreenManager enables to set the power-save setup.
NOTE
• Do your part to conserve energy, turn off the monitor when you are finished using it.
Disconnecting the monitor from the power supply is recommended to save energy
completely.
Analog Input
This monitor complies with the <VESA DPMS> (p. 49) standard and adopts a power
saving method, <EIZO MPMS> (p. 48), which works with a blank screen (totally black
screen) like “Blank Screen” ScreenSaver software.
To use the PC’s power saving system (VESA DPMS ).
[Procedure]
(1) Set the PC’s power saving settings.
(2) Select “VESA DPMS” in the <PowerManager> menu.
[Power saving system]
PC
Monitor
Power Indicator
Operation
Operation
Blue
STAND-BY
SUSPEND
Power saving
Power saving
Yellow
OFF
Operate the mouse or keyboard to return to a normal screen.
4. ADJUSTMENT 29
English
To set the power save with ScreenSaver (EIZO MPMS) software
[Procedure]
(1) Set the PC’s appropriate ScreenSaver settings or blank the screen (totally black
screen).
(2) Select <EIZO DPMS> in the <PowerManager> menu.
[Power saving system]
PC
Monitor
Power Indicator
Operation
Operation
Blue
Blank the screen
Power saving
Yellow
(ScreenSaver or Macintosh Energy
Saver)
Operate the mouse or keyboard to return to a normal screen.
NOTE
• EIZO MPMS should be used with Macintosh “EnergySaver”.
Digital Input
This monitor complies with the DVI DMPM (p. 48).
[Procedure]
(1) Set the PC’s power saving settings.
(2) Select “VESA DPMS” in the <PowerManager> menu.
[Power saving system]
PC
On
Monitor
Operation
Power Indicator
Blue
Power saving
Power saving
Yellow
Flashing yellow (2 times
for each)
Off mode
Power saving*1
*1Power saving through the PC’s off mode is only supported when “Manual”
is selected on the ScreenManager’s <Input Priority>.
[Procedure]
Operate the mouse or keyboard to return to a normal screen.
Power on the PC to return a normal screen from the Off mode of the PC.
30 4. ADJUSTMENT
English
5. ActiveShot Function
When two PCs are connected to the monitor, ActiveShot (Picture in Picture) function
allows you to display both screen images on the Main window and Sub window at the
same time. About connecting two PCs to a monitor, see p. 15.
[Example]
Main Window
1 2 3
4 5 6
A B C
D E4 5 6
A B C
D E F
1 2 3
Sub Window
Signal1
Signal 2
SIGNAL
1 - 2
AUTO
ENTER
PinP Button
Input Signal Selection Button
5-1. Operation
To display/close the Sub window
ON: Press PinP button on the control panel.
OFF: Press the PinP button again.
To switch the image of main and Sub window
Pressing the Input signal selection button (Signal 1-2) switches the signal of Main
window and Sub window.
NOTE
• When using the ActiveRotation function (p. 35), the ActiveShot function cannot be
used.
• When using the ActiveShot function, some animated images may flicker.
5. ActiveShot Function 31
English
5-2. Sub Window Settings
Display Mode
<Standard> and <Clip> modes are available for displaying the Sub window (refer to
following figures) for displaying the Sub window.
The mode is set on the <Picture in Picture> menu of ScreenManager.
[Example]
1 2 3
4 5 6
A B C
D E F
Signal1
Signal 2
<Standard> Mode
<Clip> Mode
Displaying the screen image in full
screen with reducing the image size (p.
32)
Displaying a certain part of the screen
image without reducing the image size (p.
33)
Main Window
Main Window
A B C
D E
A B
D E
3
6
Sub Window
Sub Window
<Standard> Mode
Displaying the screen image in full screen with reducing the image size in the Sub
window. Select <Standard> mode on <Picture in Picture> menu of ScreenManager.
To select the size
→
Select <Window Size>.
This sets the window size from “Large” (approx. 1/4) or “Small” (approx. 1/16).
Select the size of the Sub window, “Large” or “Small” in <Window Size>.
NOTE
• The actual Sub window size depends on the input signal.
To adjust the position
→
Select <Window Position>.
This adjusts the position of the Sub window.
Select <Window Position> and adjust the position by using the up, down, right and
left buttons.
32 5. ActiveShot Function
English
To set the Contrast
→
Select <Window Contrast>.
This controls the brightness for the each color (red, blue and green) at the same
time.
Select <Window Contrast> and adjust by using the right and left buttons.
<Clip> Mode
Displaying a certain part of the screen image in the Sub window.
Select <Clip> mode on the <Picture in Picture> menu of ScreenManager.
Main Window
A B
D E
3
6
Sub Window
Setting up the Clipping Area
→
Select <Clip Area> icon to set up the clipping area.
[Procedure]
(1)
By selecting the <Clip Area> icon, the Sub window will be displayed in
full screen and pink frame will appear on it.
(2)
Select the <Clip Position> icon. By using the up, down, right and left
buttons, position the upper-left corner of the displayed frame to the the
upper-left corner of a desired clip area. Press enter button to decide it.
(3)
(4)
Select <Clip Size>. By using the up, down, right and left buttons, adjust
the frame size to fit to a desired area on the screen image.
By selecting <Return> icon, the desired clip area is appeared as the Sub
window.
(1)
(2)
Upper Left Corner
(3)
(4)
1 2 3
4 5 6
1 2 3
4 5 6
1 2 3
4 5 6
A B
D E
3
6
Magenta Frame
Desired Clip Area
NOTE
• There is a limitation in the frame size.
5. ActiveShot Function 33
English
To adjust the position
→
Select <Window Position>.
This adjusts the position of the Sub window.
Select <Window Position> and adjust the position by using the up, down, right and
left buttons.
To set the Contrast
→
Select <Window Contrast>.
This controls the brightness for the each color (red, blue and green) at the same
time. Select <Window Contrast> and adjust by using the right and left buttons.
5-3. Settings using the Control Buttons
The brightness, contrast, size and position of the Sub window can be adjusted easily by
using the Enter button and Control buttons. Refer to the enclosed Quick Reference for
the details.
34 5. ActiveShot Function
English
6. ActiveRotation Function
ActiveRotation function allows you to change the display orientation of the monitor to
portrait without using any commercial software if you use a particular graphics card.
Refer to Web site of EIZO NANAO CORPORATION for the latest information
about the supported graphics card (http://www.eizo.com/).
Portrait
Landscape
NOTE
• When using the ActiveShot function (p. 31), the ActiveRotation function cannot be
used.
• When connecting two PCs, another screen image is not displayed in appropriate
portrait style.
Operating Procedures
Operating method depends on the graphics card.
Refer to Web site of EIZO NANAO CORPORATION.
Using the “ActiveRotation” Application (for Windows)
The application allows you to change the display orientation of the monitor to portrait
easily. Refer to the readme.txt in the EIZO LCD Utility Disk for the details.
6. ActiveRotation Function 35
English
Using the ScreenManager
(1) Select “Portrait (HW)” in the <Orientation> menu of the ScreenManager.
(2) Turn the monitor 90 degrees.
(3) Restart the PC. (If the Start button of the Windows is hidden, press the [Windows]
key or [Ctrl], [Alt] and [Delete] keys at the same time.)
(4) The display orientation will be changed to portrait. (When changing the preferred
resolution, click the [Properties]-[Settings] tab to set the resolution.)
NOTE
• When changing the display orientation to landscape again, select “Landscape”
in the <Orientation> menu of the ScreenManager and then restart the PC.
• When using the ActiveRotation function, resetting the ScreenManager causes
the monitor to be in landscape style. Restart the PC and follow the above
procedures to change the display orientation to portrait again.
When you don’t use a particular graphics card:
Use the commercial software to change the display orientation.
NOTE
• When changing the orientation of the ScreenManager, select the “Portrait(SW)”
in the <Orientation> menu of the ScreenManager.
36 6. ActiveRotation Function
English
7. Recommended Functions
Use the following functions according to need.
Function
Reference
Change the screen size when
displaying low resolutions, lower than
1280x1024.
4-2. Displaying a Low Resolutions (p. 25)
Adjust the screen (the clock, phase,
position and resolution) automatically.
4-1. Screen Adjustment (p. 21)
Set the monitor’s off timer to on or off.
Lock the adjusted settings.
Off Timer (p. 19)
Adjustment Lock (p. 19)
6. ActiveRotation Function (p. 35)
Change the display orientation of the
monitor to portrait.
When Connecting Two PCs to the Monitor:
Function
Reference
Display the Sub window.
5. ActiveShot Function (p. 31)
The Priority Input Signal (p. 16)
Select the priority input signal.
7. Recommended Functions 37
English
8. ATTACHING AN ARM
The LCD monitor can be used with an arm or stand by removing the tilt stand and
attaching the arm stand to the LCD monitor.
Using our optional arm or stand is recommended. (Ask your local dealer for
information.)
NOTE
• If you will use the arm or stand of other manufacturers, confirm the followings to the
manufacturers before selecting.
- Hole spacing on the arm mounting: 100 mm x 100 mm (VESA compliant)
- Supportable Weight: Total weight of the monitor (without stand) and attaching
equipment such as a cable
- TÜV/GS approved arm or stand
• Please connect cables after attaching an arm stand.
Setup Procedure
1. Hold the center of the stand mounting cover and slide them
rightward or leftward to remove the mounting cover.
Stand mounting cover
2. Lay the LCD monitor down. Do not scratch the panel.
3. Remove the tilt stand by loosening the screws. (4 pcs of M4 x 15
BZn/Fe)
38 8. ATTACHING AN ARM
English
4. Attach an arm stand to the LCD monitor securely.
Arm-stand
M4 Mounting Screws: M4 x 15 (mm) BZn/Fe
8. ATTACHING AN ARM 39
English
9.TROUBLESHOOTING
If a problem persists even after applying the suggested remedies, contact an EIZO dealer.
• No picture problems → See No.1 ~ No.2
• Imaging problems → See No.3 ~ No.13
• Other problems → See No.14 ~ No.19
Problems
Points to check with possible solutions
ꢀCheck that the power cord is correctly connected.
If the problem persists, turn off the monitor power
for a few minutes, then turn it back on and try
again.
1. No picture
• Indicator status: Off
ꢀCheck the “Contrast and Brightness” settings.
• Indicator status: Blue
ꢀSwitch the signal input by pressing the input signal
• Indicator status: Yellow
selection button on the front control panel.
ꢀTry pressing a key on the keyboard, or clicking the
mouse.
(p. 29)
• Indicator status: Slowly flashing
Yellow
ꢀTry pressing the power button.
• Indicator status: Flashing Yellow
(twice for each)
ꢀTry turning the PC on.
These messages appear when the signal is not inputted
correctly, even if the monitor functions properly.
2. Error messages shown below will
remain on the screen for 40
seconds.
ꢀWhen the image is displayed correctly after a short
time, there is no problem with the monitor. (Some
PCs do not output the signal soon after powering
on.)
ꢀCheck that the PC is turned ON.
ꢀCheck that the signal cable is properly connected to
the PC or graphics board.
ꢀSwitch the signal input by pressing the input signal
selection button on the front control panel.
ꢀUse the graphics board’s utility software to change
the frequency setting. (Refer to the manual of the
graphics board.)
• Whenever an error signal message
appears, the signal frequency will be
displayed in red.
(Example)
40 9. TROUBLESHOOTING
English
Problems
Points to check with possible solutions
ꢀAdjust the image position using the <Position> (p.
3. Display position is incorrect.
23)
ꢀIf the problem persists, use the graphics board’s
utility software to change the display position if
available.
ꢀAdjust the resolution using the <Resolution> (p.
4. Screen image is smaller or larger
than the actual screen images.
23)
ꢀDecrease the vertical bars using the <Clock>. (p.
5. Vertical bars of distortion appear.
22)
ꢀDecrease the horizontal bars using the <Phase>. (p.
6. Horizontal bars of distortion appear.
22)
ꢀAdjust the blurred lines using <Smoothing> (p. 26)
7. Letters and lines appear blurred.
ꢀThis happens when both composite (X-OR) input
signal and separate vertical synchronizing signal are
input. Please select one of the two.
8. Distortion appears like the figure
below.
ꢀAdjust the contrast and brightness. (The backlight
of the LCD monitor has a fixed life span. When
the screen becomes dark or begins to flicker, please
contact your dealer.)
9. The screen is too bright or too dark.
10. Afterimages appear.
ꢀWhen the screen image is changed after displaying
the same image for a long period, an afterimage
may appear. The “Afterimage” can be removed
gradually by changing the displayed image. Use the
“Off Timer” function and avoid keeping the screen
on all the time. (p. 19)
9. TROUBLESHOOTING 41
English
Problems
Points to check with possible solutions
ꢀThis is due to the characteristics of the panel itself,
11. The screen has defective pixels (e.g.
slightly light or dark).
and not the LCD product.
ꢀLeaving the screen white may solve the problem.
12. Fingerprints remain on the screen.
13. The noise appears on the screen.
ꢀChange the mode in <Signal Filter> in the <Screen>
menu.
ꢀ<Smoothing> is disabled when the screen is
14. The <Smoothing> cannot be
selected.
displayed in the 1280 x1024.
ꢀThe image size is doubled both in horizontally and
vertically to (i.e. 1280 x 960 enlarged from 640 x
480) provide clear focus which does not require
this function.
ꢀCheck that the ActiveShot (p. 31) or
ActiveRotation (p. 35) function is not used.
ꢀThe adjustment lock is probably on. To unlock:
switch the LCD monitor off. Then, while pressing
the Auto adjustment button, switch the power on.
(p. 19)
15. The Enter button does not operate.
ꢀThe Auto adjustment button does not operate
16. The Auto adjustment button does not
operate.
when the digital signal is inputted.
ꢀThe adjustment lock is probably on. To unlock:
switch the LCD monitor off. Then, while pressing
the Auto adjustment button, switch the power on.
(p. 19)
ꢀThe Auto sizing function is intended for use on the
Macintosh and on AT-compatible PC running
Windows. It may not work properly in either of
the following cases.
When running an AT-compatible PC on MS-DOS
(Not windows). The background color for the
“wall paper” or “desktop” pattern is set to black.
Some signals from a graphics board may not
function properly.
42 9. TROUBLESHOOTING
English
Problems
Points to check with possible solutions
ꢀUse the graphics board’s utility software to change
17. Frequency does not change after
installing “Monitor information file”
in the attached utility disk on
Windows 98/2000/XP.
the input signal frequency.
ꢀCheck that the ActiveRotation function is not used.
18. The ActiveShot function cannot be
operated.
(p. 35)
ꢀCheck that the ActiveShot function is not used. (p.
19. The ActiveRotation function cannot
be operated.
31)
9. TROUBLESHOOTING 43
English
10. CLEANING
Periodic cleaning is recommended to keep the monitor looking new and to prolong its
operation lifetime.
NOTE
• Never use thinner, benzene, alcohol (ethanol, methanol, or isopropyl alcohol),
abrasive cleaners, or other strong solvents, as these may cause damage to the
cabinet or LCD panel.
Cabinet
To remove stains, wipe the cabinet with a soft, lightly moistened cloth using a mild
detergent. Do not spray wax or cleaner directly into the cabinet. (For details, refer to
the manual of the PC.)
LCD Panel
• The LCD surface can be cleaned with a soft cloth, such as cotton or lens paper.
• If necessary, stubborn stains can be removed by moistening part of a cloth with water
to enhance its cleaning power.
44 10. CLEANING
English
11. SPECIFICATIONS
LCD Panel
46 cm (18.1 inch), TFT color LCD panel with Anti-Glare
Hard Coating, Viewing Angle: Horizontal: 170°, Vertical:
170°
Response Time: approx. 40 ms
0.2805 mm
Dot Pitch
Horizontal Scan Frequency
Vertical Scan Frequency
Analog: 30 ∼ 82 kHz (Automatic), Digital: 30 ~ 81 kHz
Analog: 49 ∼ 86 Hz (Automatic)
(1280 x 1024: ∼ 76 Hz)
Digital: 59 ∼ 61 Hz, (VGA TEXT : 70Hz)
1280 dots x 1024 lines
Resolution
Dot Clock (Max.)
Display Colors
Display Area
Analog: 140 MHz, Digital: 120 MHz
16 million colors (max)
359 mm (H) x 287 mm (V) (14.1” (H) x 11.3” (V))
(Viewable image size: 459 mm (18.1”))
100-120/200-240 VAC±10%, 50/60 Hz, 0.7 /0.4 A
Min.: 52 W
Power Supply
Power Consumption
Max.: 59 W (With speaker)
Power Saving Mode: Less than 3 W (When the optional
speaker is not connected.)
Input Connector
D-Sub mini 15 pin, DVI-I
Analog Input Signal (Sync) a) Separate, TTL, Positive/Negative
b) Composite, TTL, Positive/Negative
c) Sync on Green, 0.3 Vp-p, Negative (except in portrait
style)
Analog Input Signal (Video)
Input Signal (Digital)
Signal registration
Plug & Play
0.7Vp-p/75Ω Positive
TMDS (Single Link))
55 (Factory preset: 25)
VESA DDC 2B
Dimensions
399 mm (W) x 403.5∼ 503.5 mm (H) x 202.7 mm (D)
(15.7”(W) x 15.9” ∼ 19.8” (H) x 8.0”(D))
Dimensions (without stand) 399mm (W) x 328mm (H) x 65mm (D) (15.7”(W) x
12.9”(H) x 2.6”(D))
Weight
7.6kg (16.8 lbs.)
Weight (without stand)
Temperature
5.3kg (11.7 lbs.)
Operating: 0°C ∼ 35°C (32°F ∼ 95°F)
Storage: -20°C ∼ 60°C (-4°F ∼ 140°F)
Humidity 30% to 80% R.H. Non-condensing
Certifications and Standards
100-120 VAC
NRTL/C-TÜV, FCC-B, EPA ENERGY STAR Program,
TÜV/Rheinland Ergonomics Approved
CE, CB, TÜV Rheinland/GS, EPA ENERGY STAR
Program, TÜV/Rheinland Ergonomics Approved
Max 78 ms
200-240 VAC
Image Formation Time*
*Test result according to the ISO13406-2 standard from a certified testing laboratory.
11. SPECIFICATIONS 45
English
Default settings
Analog input
100%
Digital input
100%
Contrast
Brightness
100%
100%
Smoothing
3
ColorManagement
Color Mode
Temperature
Custom
Off (Normal white)
VESA DPMS
Full
PowerManager
Screen Size
DVI DMPM
Input Priority
Menu Off Timer
Menu Settings
Signal 1
Disable
Normal
Menu Size
Menu Off Timer
45 seconds
On
Beep
Orientation
Power Indicator
Language
Landscape
Enable
English
Beeper settings
Short beep
ScreenManager item selected.
ScreenManager parameter adjusted to minimum or maximum
limit.
Input signal selection button pressed.
Auto Adjustment button pressed.
ScreenManager data-save executed.
Monitor not connected correctly.
PC turned off.
Long beep
4 short beeps
Monitor received unsupported signal frequency.
2 short beeps every
15 sec.
Monitor is in the advance notice mode of the Off Timer. The
power will be off within fifteen minutes.
mm (inches)
Dimensions
399 (15.7)
3.0 (0.12)
361 (14.2)
3.0 (0.12)
168 (6.6)
TILT
1
SWIVEL
315.5 (12.42)
46 11. SPECIFICATIONS
English
Pin Assignment
D-Sub mini 15 pin connector
4
3
2
1
5
10
9
8
7
6
11
14 13 12
15
Pin
No.
Signal
Pin
No.
Signal
Pin
No.
Signal
1
Red video
Green video
Blue video
Ground
6
7
8
9
Red ground
11 Ground Shorted
2
Green ground 12
Blue ground 13
Data (SDA)
H. Sync
3
4
No pin
14
V. Sync
5
No pin
10 Ground Shorted 15
Clock (SCL)
DVI-I Connector
3
1
9
17
2
4
12
20
6
7
8
16
24
5
13
21
C1 C2
10 11
19
14 15
22 23
C3 C4
C5
18
Pin No.
Signal
Pin No.
Signal
Pin No.
Signal
1
2
3
TMDS Data2-
TMDS Data2+
TMDS Data2/4 Shield
11
12
13
TMDS Data1/3 Shield
21
22
23
NC
NC
NC
TMDS Clock shield
TMDS Clock+
4
5
NC*
NC
14
+5V Power
24
C1
TMDS Clock-
Analog Red
15 Ground (return for +5V,
Hsync and Vsync)
6
7
8
9
DDC Clock (SCL)
DDC Data (SDA)
Analog Vertical Sync
TMDS Data1-
16
17
18
19
Hot Plug Detect
TMDS Data0-
TMDS Data0+
C2
C3
C4
C5
Analog Green
Analog Blue
Analog Horizontal Sync
TMDS Data0/5 Shield
Analog Ground
(analog R, G, & B return)
10
TMDS Data1+
20
NC
(*NC: No Connection)
11. SPECIFICATIONS 47
English
12. GLOSSARY
Afterimage
The Afterimage is particular to LCD monitors when the monitor screen is left on for a
long period without use. The “Afterimage” can be removed gradually by changing
the displayed image.
Clock
With the analog input signal display, the analog signal is converted to a digital signal
by the LCD circuitry. To convert the signal correctly, the LCD monitor needs to
produce the same number clock pulse as the dot clock of the graphics system. When
the clock pulse is not correctly set, some vertical bars of distortion are displayed on
the screen.
DVI
(Digital Visual Interface)
A digital flat panel interface. DVI can transmit digital data from the PC directly
without loss with the signal transition method “TMDS”.
There are two kinds of DVI connectors. One is DVI-D connector for digital signal
input only. The other is DVI-I connector for both digital and analog signal inputs.
DVI DMPM
(DVI Digital Monitor Power Management)
The Power management system for the digital interface. The “Monitor ON” status
(operation mode) and the “Active Off” status (power-saving mode) are indispensable
for the DVI-DMPM as the monitor’s power mode.
EIZO MPMS
(EIZO Monitor PowerManager Signaling)
EIZO MPMS, “EIZO Monitor PowerManager Signaling” also enables power saving
on the monitor side. EIZO MPMS recognizes video signals from the PC when the PC
is in a power saving mode, and reduces energy consumption of the monitor.
Gain Adjustment
Adjusts each color parameter for red, green and blue. The color of the LCD monitor
is displayed through the color filter of the LCD panel. Red, green and blue are the
three primary colors. The colors on the monitor are displayed by combining these
three colors. The color tone can change by adjusting the illumination amount passed
through each color’s filter.
Phase
The phase adjustment decides the sampling timing point for converting the analog
input signal to a digital signal. Adjusting the phase after the clock adjustment will
produce a clear screen.
48 12. GLOSSARY
English
Range Adjustment
The Range Adjustment controls the level of output signal range to display the whole
color gradation.
Resolution
The LCD panel consists of a fixed number of pixel elements which are illuminated to
form the screen image. The EIZO L695 display panel consists of 1280 horizontal
pixels and 1024 vertical pixels. At a resolution of 1280 x 1024, all pixels are
displayed as a full screen.
sRGB (Standard RGB)
“International Standard for Red, Green, and Blue color space”
A color space was defined with the aim of the color matching between applications
and hardware devices, such as monitors, scanners, printers and digital cameras. As a
standard default space, sRGB allows Internet users to closely match colors.
Temperature
Color temperature is a method to measure the white color tone, generally indicated in
degrees Kelvin. At high temperatures the white tone appears somewhat blue, while at
lower temperatures it appears somewhat red. Computer monitors generally give best
performance at high temperature settings.
5,000K: Often used in printing industry.
6,500K: Good for video-image display.
9,300K: Default setting for your EIZO monitor.
TMDS
(Transition Minimized Differential Signaling)
A signal transition method for the digital interface
VESA DPMS
(Video Electronics Standard Association – Display Power Management Signaling)
The acronym VESA stands for “Video Electronics Standards Association”, and DPMS
stands for “Display Power Management Signaling.” DPMS is a communication
standard that PCs and graphics boards use to implement power savings on the
monitor side.
12. GLOSSARY 49
APPENDIX/ANHANG/ANNEXE
Preset Timing Chart for Analog input
Timing-Übersichten für Analog Eingang
Synchronisation des Signaux pour Analog numerique
Based on the signal diagram shown below 25 factory presets have been registered in the
monitor's microprocessor.
Der integrierte Mikroprozessor des Monitors unterstützt 25 werkseitige
Standardeinstellungen (siehe hierzu die nachfolgenden Diagramme).
25 signaux ont été enregistrés en usine dans le microprocesseur du moniteur,
conformément au diagramme de synchronisation ci-dessous.
Frequencies
Sync Polarity
Dot Clock
MHz
Mode
H kHz
V Hz
H
V
VGA 640 × 480 @60 Hz
25.175
28.322
30.240
57.280
100.000
126.200
31.500
31.500
36.000
36.000
40.000
50.000
49.500
56.250
65.000
75.000
78.750
94.500
108.000
108.000
108.000
135.000
94.200
107.500
117.000
31.469
31.468
35.000
49.722
68.681
74.763
37.861
37.500
43.269
35.156
37.879
48.077
46.875
53.674
48.363
56.476
60.023
68.677
67.500
60.000
63.981
79.976
61.974
71.858
71.691
59.940
70.087
66.667
74.546
75.062
74.763
72.809
75.000
85.008
56.250
60.317
72.188
75.000
85.061
60.004
70.069
75.029
84.997
75.000
60.000
60.020
75.025
66.141
76.202
67.189
Nega.
Nega.
Nega.
Nega.
Nega.
Posi.
Nega.
Posi.
Nega.
Nega.
Nega.
Posi.
Nega.
Nega.
Nega.
Posi.
Posi.
Posi.
Posi.
Posi.
Nega.
Nega.
Posi.
Posi.
Posi.
Posi.
Posi.
Posi.
VGA 720 × 400 @70 Hz
Macintosh 640 × 480 @67 Hz
Macintosh 832 × 624 @75 Hz
Macintosh 1152 × 870 @75 Hz
Macintosh 1280 × 960 @75 Hz
VESA 640 × 480 @72 Hz
VESA 640 × 480 @75 Hz
VESA 640 × 480 @85 Hz
VESA 800 × 600 @56 Hz
VESA 800 × 600 @60 Hz
VESA 800 × 600 @72 Hz
VESA 800 × 600 @75 Hz
VESA 800 × 600 @85 Hz
VESA 1024 × 768 @60 Hz
VESA 1024 × 768 @70 Hz
VESA 1024 × 768 @75 Hz
VESA 1024 × 768 @85 Hz
VESA 1152 × 864 @75 Hz
VESA 1280 × 960 @60 Hz
VESA 1280 × 1024 @60 Hz
VESA 1280 × 1024 @75 Hz
Workstation 1152 × 960 @66 Hz
Workstation 1152 × 960 @76 Hz
Workstation 1280 × 1024 @67 Hz
Nega.
Nega.
Nega.
Posi.
Posi.
Posi.
Posi.
Posi.
Nega.
Nega.
Posi.
Posi.
Posi.
Posi.
Posi.
Posi.
Composite, Nega.
Composite, Nega.
Composite, Nega.
APPENDIX/ANHANG/ANNEXE
i
For U.S.A, Canada, etc. (rated 100-120 Vac) Only
FCC Declaration of Conformity
We, the Responsible Party
EIZO NANAO TECHNOLOGIES INC.
5710 Warland Drive, Cypress, CA 90630
Phone: (562) 431-5011
declare that the product
Trade name: EIZO
Model: FlexScan L695
is in conformity with Part 15 of the FCC Rules. Operation of this product is subject to the
following two conditions: (1) this device may not cause harmful interference, and (2) this
device must accept any interference received, including interference that may cause undesired
operation.
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of the following measures.
* Reorient or relocate the receiving antenna.
* Increase the separation between the equipment and receiver.
* Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
* Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
Note
Use the attached specified cable below or EIZO signal cable with this monitor so as to keep
interference within the limits of a Class B digital device.
- AC Cord
- Shielded Signal Cable (enclosed)
Canadian Notice
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de le classe B est comforme à la norme NMB-003 du Canada.
Recycle Auskunft
Die Rücknahme dieses Produktes nach Nutzungsende übernimmt EIZO in Deutschland
zusammen mit dem Partner von Roll MBB Recycling GmbH. Dort werden die Geräte in ihre
Bestandteile zerlegt, die dann der Wiederverwertung zugeführt werden. Um einen Abholtermin
zu vereinbaren und die aktuellen Kosten zu erfahren, benutzen Sie bitte folgende Rufnummer:
02153-73 35 00. Weitere Informationen finden Sie auch unter der Internet-Adresse:
Recycling Information for customers in Switzerland:
All recycling information is placed in the SWICO’s website.
Recycling-Information für Kunden in der Schweiz:
Alle Informationen zum Thema Recycling finden Sie auf der Homepage des Brancheverbandes
SWICO.
Renseignements de recyclage pour les clients en Suisse:
Vous trouvez tous les renseignements pour le sujet de recyclage sur la page WEB de I’UNION
DE BRAN CHE SWICO.
Recycling Information for customers in USA:
All recycling information is placed in the EIZO Nanao Technologies, Inc’s website.
Återvinnings information för kunder i Sverige:
All information om återvinning finns på Eizo Nordics hemsida:
Hinweis zur Ergonomie :
Dieser Monitor erfüllt die Anforderungen an die Ergonomie nach EK1-ITB 2000 mit dem
Videosignal, 1280 Punkte × 1024 Zeilen, RGB analog, 0,7 Vp-p und mindestens 75,0 Hz
Bildwiederholfrequenz, non interlaced. Weiterhin wird aus ergonomischen Gründen empfohlen,
die Grundfarbe Blau nicht auf dunklem Untergrund zu verwenden (schlechte Erkennbarkeit,
Augenbelastung bei zu geringem Zeichenkontrast.)
|