CONTENTS
Chapter 1 Features and Overview
1-1 Features
1-2 Buttons and Indicators
1-3 Functions and Basic Operation
Chapter 2 Settings and Adjustments
2-1 Utility Disk
2-2 Screen Adjustment
2-3 Color Adjustment
2-4 Off Timer/Power Saving Settings
2-5 Screen Size Selection
2-6 Power Indicator/EIZO Logo Display Setting
2-7 Beeper Settings
Important
2-8 Locking Buttons
2-9 Setting Adjustment Menu Display
2-10 Setting Orientation
Please read PRECAUTIONS, this User’s
Manual and Setup Manual (separate
volume) carefully to familiarize yourself
with safe and effective usage.
2-11 Viewing Information/Setting Language
2-12 Setting BrightRegulator
2-13 Resumption of Default Setting
Chapter 3 Connecting Cables
3-1 Connecting Two PCs to the Monitor
3-2 Connecting Peripheral USB Devices
Chapter 4 Troubleshooting
Chapter 5 Reference
5-1 Attaching an Arm
5-2 Cleaning
5-3 Specifications
5-4 Glossary
5-5 Preset Timing
How to Setup
Please read the Setup Manual (separate volume)
Notice for this monitor
In order to suppress the luminosity change by long-term use and to maintain the stable luminosity, use of a monitor in
lower brightness is recommended.
The LCD panel is manufactured using high-precision technology. However, note that the appearance of any missing
pixels or lit pixels does not indicate damage to the LCD monitor.
Percentage of effective pixels: 99.9994% or higher.
The backlight of the LCD panel has a fixed life span. When the screen becomes dark or begins to flicker, please contact
your dealer.
Do not press on the panel or edge of the frame strongly, as this may result in the display malfunction, such as the
interference patterns, etc. If pressure is continually applied to the LCD panel, it may deteriorate or damage your LCD
panel. (If the pressure marks remain on the LCD panel, leave the monitor with a white or black screen. The symptom
may disappear.)
Do not scratch or press on the panel with any sharp objects, such as a pencil or pen as this may result in damage to the
panel. Do not attempt to brush with tissues as this may scratch the LCD panel.
When the monitor is cold and brought into a room or the room temperature goes up quickly, dew condensation
may occur inside and outside the monitor. In that case, do not turn the monitor on and wait until dew condensation
disappears, otherwise it may cause damage to the monitor.
When the screen image is changed after displaying the same image for extended periods of time, an afterimage may
appear. Use the screen saver or timer to avoid displaying the same image for extended periods of time.
To use the monitor comfortably
An excessively dark or bright screen may affect your eyes. Adjust the brightness of the monitor according to the
environmental conditions.
Staring at the monitor for a long time tires your eyes. Take a 10-minute rest every hour.
1
CONTENTS
Notice for this monitor.............................................. 1
2-8 Locking Buttons ............................................ 18
● To lock operation [Adjustment Lock]................. 18
To use the monitor comfortably............................... 1
2-9 Setting Adjustment Menu Display................ 18
● To update menu settings [Menu Size/Menu
Chapter 1 Features and Overview ..................... 3
Position/Menu Off Timer/Translucent] .............. 18
1-1 Features............................................................ 3
1-2 Buttons and Indicators.................................... 3
1-3 Functions and Basic Operation...................... 4
2-10 Setting Orientation ........................................ 19
● To set the orientation of the Adjustment menu
[Orientation]...................................................... 19
2-11 Viewing Information/Setting Language ....... 19
● To check settings, usage time, etc.
Chapter 2 Settings and Adjustments ................ 7
[Information] ..................................................... 19
● To set a language to be displayed
2-1 Utility Disk ........................................................ 7
● EIZO LCD Utility Disk (CD-ROM)....................... 7
● UniColor Pro (CD-ROM)..................................... 7
[Language] ....................................................... 19
2-12 Setting BrightRegulator ................................ 20
● To set automatic brightness adjustment
2-2 Screen Adjustment.......................................... 8
Digital Input............................................................ 8
Analog Input .......................................................... 8
[BrightRegulator] .............................................. 20
2-13 Resumption of Default Setting ..................... 20
● To reset color adjustment [Reset]..................... 20
● To reset all settings [Reset] .............................. 20
2-3 Color Adjustment............................................11
Simple adjustment [FineContrast mode] ...........11
● FineContrast Mode............................................11
● To select FineContrast mode.............................11
● To update color setting of FineContrast mode...11
Chapter 3 Connecting Cables .......................... 21
3-1 Connecting Two PCs to the Monitor............ 21
● To set priority of PC to be displayed
Advanced Adjustments [Adjustment menu]..... 12
●
To select an appropriate mode for images ....... 12
[Input Priority] ................................................... 22
● To set/adjust color ............................................ 13
3-2 Connecting Peripheral USB Devices ........... 23
Chapter 4 Troubleshooting............................... 24
2-4 Off Timer/Power Saving Settings................. 14
● To set monitor power-off time [Off Timer] ......... 14
● To set monitor power-saving
[VESA DPMS/DVI DMPM]................................ 15
Chapter 5 Reference ......................................... 26
2-5 Screen Size Selection.................................... 16
● To change screen size [Screen Size] ............... 16
● To adjust brightness of non-display area
5-1 Attaching an Arm........................................... 26
5-2 Cleaning.......................................................... 27
5-3 Specifications ................................................ 28
5-4 Glossary ......................................................... 33
5-5 Preset Timing................................................. 35
[Border Intensity] .............................................. 16
2-6 Power Indicator/EIZO Logo Display Setting
......................................................................... 17
● To turn off the Power indicator while a screen is
displayed [Power Indicator] .............................. 17
● To display EIZO logo [EIZO Logo Appearing
Function]........................................................... 17
2-7 Beeper Settings ............................................. 17
● To set the beeper [Beep] .................................. 17
CONTENTS
2
Chapter 1 Features and Overview
Thank you very much for choosing an EIZO color LCD monitor.
1-1 Features
• 24.1 (SX2461W) / 27.0 (SX2761W) inch class wide screen format LCD
• Applicable to HDCP
• Dual-input compliant (DVI-I ×2 connectors)
• DVI digital input (TMDS) compliant
• Horizontal scan frequency, Vertical scan frequency and Resolution are as follows;
Horizontal scan frequency Analog
Digital
24 - 94 kHz
31 - 76 kHz
Vertical scan frequency
Analog
Digital
49 - 86 Hz
49 - 76 Hz (1600 × 1200)
49 - 61 Hz (1920 × 1200)
59 - 61 Hz
69 - 71 Hz (VGA TEXT)
Resolution
1920 dots × 1200 lines
NOTE
• Compatible with frame synchronization mode 59 - 61 Hz
• This monitor supports the Portrait/
Landscape display. This function
allows you to change the orientation
of the Adjustment menu when using
the monitor screen in vertical display
position. (Refer to “2-10 Setting
Orientation” on page 19.)
* Only if the [Full Screen] or [Enlarged] is selected from the <Screen Size>.
• Smoothing (soft - sharp) function for adjustment of enlarged images
• FineContrast mode to allow the best mode for screen display
• The application software “UniColor Pro” to simulate the views experienced
by people with some sort of color deficiency is included (refer to the
UniColor Pro (CD-ROM)).
• If you use the monitor with “Portrait”
position, the setting may be required
to change depending on the graphics
board used in your PC. Refer to the
manual of the graphics board for
details.
• The utility software “ScreenManager Pro for LCD” (for Windows) to control
the monitor from a PC with mouse/keyboard is included (refer to the EIZO
LCD Utility Disk (CD-ROM)).
• BrightRegulator function incorporate
• Height adjustable stand
• The stand of the unit can be replaced
with an arm or another stand. (Refer
to “5-1 Attaching an Arm” on page
26.)
• Portrait/Landscape display available (rotate 90 degrees clockwise)
1-2 Buttons and Indicators
Adjustment menu (*ScreenManager ®
)
Button
1
3 4
5
6
7
8 9
2
1. Sensor (BrightRegulator)
2. Adjustment lock button
6. Enter button
7. Control buttons (Left, Down, Up, Right)
8. Power button
NOTE
3. Input signal selection button
4. Mode button
• While the screen is displayed, the
power indicator that is lighting blue
can be turned off (see “To turn off
the Power indicator while a screen is
displayed [Power Indicator]” on page
17).
• For the power indicator status with
“Off Timer” set, refer to “To set
monitor power-off time [Off Timer]”
on page 14.
9. Power indicator
5. Auto button
Indicator status
Operation status
Blue
The screen is displayed
Power saving
Orange
Off
Power off
*
ScreenManager ® is an EIZO’s nickname of the Adjustment menu.
Chapter 1 Overview and Features
3
1-3 Functions and Basic Operation
To adjust the screen and color
Main menu (Refer to page 6 for operation)
Analog input only
1
Screen Adjustment
(Automatic Adjustment)
Page 8
Press
Press
.
again.
2
Screen Adjustment
Page 9
(Advanced Adjustment)
[At analog signal input] [At digital signal input]
• The Adjustment menu and the FineContrast menu
cannot be displayed at the same time.
FineContrast mode
Page 11
Color Adjustment
●
●
*
To eliminate vertical bars [Clock ]… see page 9
To remove flickering or blurring
Simple Adjustment [FineContrast mode]
This function allows easy selection of a desired
mode from five modes according to monitor
application.
*
[Phase ] …………………………… see page 9
●
●
●
●
●
To correct screen position
*
[Position ] ………………………… see page 9
To adjust extra or cut image
*
[Resolution ]………………………… see page 10
To adjust color gradation automatically
[Range Adjustment ] ……………… see page 10
To modify blurred characters/lines
[Smoothing] ………………………… see page 10
To set when a noise appears on the screen
*
*
[Signal Filter ] ……………………… see page 24
*
*
Items marked with can be adjusted with analog
input.
Color Adjustment
Page 12
(Advanced Adjustment)
●
“Brightness,” “Temperature,” and “Gamma”
can be set for each mode (Custom/sRGB/Text/
Picture/Movie).
Settable functions vary with the display mode.
●
“Brightness”, “Temperature”, “Gamma”,
“Saturation”, “Hue”, “Gain” and “6 Colors” can be
set for each mode (Custom/sRGB/Text/Picture/
Movie).
Page 12
Brightness Adjustment
Press
or
to adjust brightness.
Settable functions vary with the display mode.
Resuming the default settings
●
To reset color adjustment [Reset] … see page 20
Chapter 1 Overview and Features
4
To make useful settings/adjustments
Adjustment menu (Refer to page 6 for operation)
Power-save Settings
Page 15
●
To set monitor power-saving
[VESA DPMS/DVI DMPM]
Information
Page 19
Set the off timer
●
To set monitor power-off time
[Off Timer] …………………………… see page 14
Change the screen size
●
To change screen size
●
To check settings, usage time, etc. [Information]
[Screen Size] ……………………… see page 16
To adjust brightness of non-display area
[Border Intensity] …………………… see page 16
●
BrightRegulator Setting
Language
Page 19
●
To set automatic brightness adjustment
[BrightRegulator] …………………… see page 20
Orientation Setting
●
To set the orientation of the Adjustment menu
[Orientation] ………………………… see page 19
Power Indicator Setting
●
To turn off the Power indicator while a screen is
displayed [Power Indicator] ……… see page 17
●
To set a language to be displayed [Language]
Beeper setting
●
To set the beeper [Beep]…………… see page 17
Adjustment menu settings
EIZO Logo Display Setting
●
To update menu settings [Menu Size/Menu
Position/Menu Off Timer/
●
To display EIZO logo [EIZO Logo Appearing
Function] ……………………………… see page 17
Translucent] ………………………… see page 18
Locking Adjustment
Resume the factory default settings
●
To lock operation [Adjustment Lock]… see page 18
●
To reset all settings [Reset] ……… see page 20
Connecting Signal Cables
Connect two PCs
●
To set priority of PC to be displayed
[Input Priority] ……………………… see page 22
●
●
Connecting Two PCs to the Monitor … see page 21
Connecting Peripheral USB Devices… see page 23
Chapter 1 Overview and Features
5
Basic operation of Adjustment menu
[Displaying Adjustment menu and selecting function]
(1) Press
. The Main menu appears.
(2) Select a function with
(3) Select a function with
/
/
/
/
/
/
, and press
, and press
. The Sub menu appears.
. The adjustment/setting menu appears.
, and press . The setting is saved.
(4) Adjust the selected item with
/
/
/
[Exiting Adjustment menu]
(1) Choose <Return> from the Sub menu and press
(2) Choose <Exit> from the Main menu and press
. The Main menu appears.
. The Adjustment menu quits.
NOTE
• The Adjustment menu can also be exited by pressing
twice quickly.
• <Exit> or <Return> can also be selected by pressing
twice in the Main menu or Sub menu.
Chapter 1 Overview and Features
6
Chapter 2 Settings and Adjustments
2-1 Utility Disk
“EIZO LCD Utility Disk” (CD-ROM) and “UniColor Pro” (CD-ROM) are supplied with the monitor. The following
table shows the disk contents and the overview of the application software programs.
●
EIZO LCD Utility Disk (CD-ROM)
Item
Overview
For Windows
For Macintosh
A “Readme.txt” or “read me” file
Color Profiles (ICC Profiles)
✓
✓
A specific file including the color
characteristic information for the monitor.
✓
✓
✓
Screen Adjustment Utility
Monitor pattern display software used when
adjusting the image of the analog input
signal manually.
−
Screen adjustment pattern files
Used when adjusting the image of the
analog signal input manually. If the Screen
Adjustment Utility is not applicable to your
PC, use this pattern files to adjust the image.
✓
✓
ScreenManager Pro for LCD
A utility software program to control monitor
adjustments from a PC using its mouse and
keyboard. (A PC must be connected to the
monitor with the supplied USB cable. For
more information, refer to “Chapter 3 3-2
Connecting Peripheral USB Devices”.)
−
✓
WindowMovie Checker Software
WindowMovie is a function of
ScreenManager Pro for LCD.
For more information, refer to the User’s
Manual of ScreenManager Pro for LCD on
the EIZO LCD Utility Disk (CD-ROM).
User’s Manual of this monitor (PDF file)
To use ScreenManager Pro for LCD
For the installation and use of ScreenManager Pro for LCD, refer to its User’s Manual on the EIZO LCD Utility Disk
(CD-ROM).
●
UniColor Pro (CD-ROM)
Item
Overview
For Windows
For Macintosh
UniColor Pro
An application software to simulate the
views experienced by some color deficiency
people. (A PC must be connected to the
monitor with the supplied USB cable. For
more information, refer to “Chapter 3 3-2
Connecting Peripheral USB Devices”.)
✓
✓
UniColor Pro User’s Manual (PDF file)
Color Universal Design Handbook (PDF file)
To use UniColor Pro
For the installation and use of UniColor Pro, refer to the UniColor Pro User’s Manual on the UniColor Pro (CD-ROM).
Chapter 2 Settings and Adjustments
7
2-2 Screen Adjustment
Digital Input
When digital signals are input, images are displayed correctly based on the
preset data of the monitor. When performing the advanced adjustment, see “2-3
Color Adjustment” (page 11) and its subsequence pages.
Attention
Analog Input
• Wait 30 minutes or more from
monitor power on before starting
adjustments.
The monitor screen adjustment is used to suppress flickering of the screen or
adjust screen position and screen size correctly according to the PC to be used.
To use the monitor comfortably, adjust the screen when the monitor is set up for
the first time or when the settings of the PC in use are updated. No adjustment
is required when the image appears correctly.
[Adjustment Procedure]
Attention
Perform the auto size adjustment.
1
• This function works correctly when
an image is fully displayed over the
Windows or Macintosh display area.
It does not work properly when an
image is displayed only on a part of
the screen (command prompt window,
for example) or when a black
background (wallpaper, etc.) is in use.
• This function does not work correctly
with some graphics boards.
● To adjust flickering, screen position, and screen size
automatically [Auto button]
(1) Press
.
A message “Your setting will be lost, if you press again now” appears for
five seconds.
(2) Press
again while the message is displayed.
The Auto Adjustment function begins (showing a running status icon) to
adjust flickering, screen position, and screen size automatically.
Prepare the display pattern for the analog display adjustment.
NOTE
2
3
• For how to open and use the screen
adjustment pattern files, refer to
“Readme.txt” or the “read me” file.
When you are using a Macintosh PC,
you can open the file directly from the
start menu of the disk.
(1) Load the “EIZO LCD Utility Disk” to your PC.
(2) For Windows PC: Start the “Screen Adjustment Utility” from the
startup menu on the disk.
For other than Windows PC: Use the screen adjustment pattern files.
• If the screen is displayed correctly : go to step 5
• If the screen is not displayed correctly : go to step 3
Perform the auto size adjustment again with the analog screen
adjustment pattern displayed.
● To adjust flickering, screen position, and screen size
automatically [Auto button]
(1) Display Pattern 1 in full screen on the monitor using the “Screen
Adjustment Utility” or the screen adjustment pattern files.
Chapter 2 Settings and Adjustments
8
(2) Press
.
A message “Your setting will be lost, if you press again now” appears for
five seconds.
(3) Press
again while the message is displayed.
The Auto Adjustment function begins (showing a running status icon) to
adjust flickering, screen position, and screen size automatically.
• If the screen is displayed correctly : go to step 5
• If the screen is not displayed correctly : go to step 4
NOTE
Perform advanced adjustments for the following using the
<Screen> menu of the Adjustment menu.
4
• Press the control button slowly so as
not to miss the adjustment point.
• When blurring, flickering or bars
appear on the screen after adjustment,
proceed to [Phase] to remove
flickering or blurring.
● To eliminate vertical bars [Clock]
(1) Choose <Clock> from the <Screen> menu, and press
The <Clock> menu appears.
.
(2) Adjust the clock with
or
, and press
.
The adjustment is completed.
Attention
● To remove flickering or blurring [Phase]
• Flickering or blurring may not be
eliminated depending on your PC or
graphics board.
(1) Choose <Phase> from the <Screen> menu, and press
The <Phase> menu appears.
.
(2) Adjust the phase with
or
, and press
.
The adjustment is completed.
NOTE
● To correct screen position [Position]
• When vertical bars appear on the
screen after adjustment, go back to
“To eliminate vertical bars [Clock].”
(Clock → Phase → Position)
Since the number of pixels and the pixel positions are fixed on
the LCD monitor, only one position is provided to display images
correctly. The position adjustment is made to shift an image to the
correct position.
(1) Choose <Position> from the <Screen> menu, and press
The <Position> menu appears.
.
(2) Adjust the position with
/
/
/
to display the image
properly in the display area of the monitor.
Chapter 2 Settings and Adjustments
9
● To adjust extra or cut image [Resolution]
This adjustment is available to equalize the resolution shown on the
Setting menu and the resolution of input signal.
(1) Choose <Resolution> from the <Screen> menu, and press
The <Resolution> menu appears.
.
(2) Adjust the vertical resolution with
resolution with or , and press
or
.
, and then horizontal
The adjustment is completed.
Extra image is displayed due to excessive dots.
A part of image is cut due to short dots.
Adjust the color gradation.
5
● To adjust color gradation automatically [Range Adjustment]
Every color gradation (0 to 255) can be displayed by adjusting the
signal output level.
(1) Display Pattern 2 in full screen on the monitor using the “Screen
Adjustment Utility” or the screen adjustment pattern files.
(2) Choose <Range Adjustment> from the <Screen> menu, and press
.
A message “Your setting will be lost it you press AUTO button” appears.
(3) Press
while the message is displayed.
Color gradation is adjusted automatically.
(4) Close the Pattern 2. When using the “Screen Adjustment Utility”,
close the program.
Attention
Change the smoothing setting.
6
• Smoothing setting may not be required
depending on the display resolution.
(You cannot choose the smoothing
icon.)
● To modify blurred characters/lines [Smoothing]
When a low-resolution image is displayed in the “Full Screen” or
“Enlarged” mode, the characters or lines of the displayed image may
be blurred.
(1) Choose <Screen> from the Adjustment menu, and press
(2) Choose <Smoothing> from the <Screen> menu, and press
The <Smoothing> menu appears.
.
.
(3) Adjust the characters/lines with
or
, and press
.
The smoothing adjustment is completed.
Chapter 2 Settings and Adjustments
10
2-3 Color Adjustment
Simple adjustment [FineContrast mode]
This function allows you to select the best display mode for monitor brightness,
etc.
●
FineContrast Mode
An appropriate display mode is selectable out of five modes.
Mode
Custom
Purpose
Available for making desired setting.
Suitable for color matching with sRGB compatible
peripherals.
sRGB
Text
Suitable for displaying texts for word processing or
spreadsheets.
Suitable for displaying images such as photos or picture
images.
Picture
Movie
Suitable for playing back animated images.
FineContrast menu
Example) Custom
Displays current mode.
Displays current settings of brightness, color
temperature, and gamma.
NOTE
• The Adjustment menu and the
FineContrast menu cannot be
displayed at the same time.
●
To select FineContrast mode
(1) Press
.
The FineContrast menu appears at the lower left of the screen.
(2) One of five modes is displayed in turn each time
is pressed.
Custom sRGB Text Picture Movie
(3) Choose desired mode and press
The setting completes.
.
Attention
●
To update color setting of FineContrast mode
• Color temperature values and gamma
values are fixed in some modes.
Set them as shown in “To select an
appropriate mode for images” on page
12.
<Brightness>, <Temperature>, and <Gamma> can be set or adjusted.
(1) Choose a desired function from the FineContrast menu with or
.
(2) Adjust the selected function with
The adjustment is completed.
or
, and press
.
NOTE
• The <Color> menu of the Adjustment
menu allows advanced color
adjustments for each mode. Refer to
“To select an appropriate mode for
images” on page 12.
Chapter 2 Settings and Adjustments
11
Attention
Advanced Adjustments [Adjustment menu]
• Perform [Range Adjustment] before
starting color adjustment for analog
input signals.
Independent setting and saving of color adjustment are available for each
FineContrast mode.
Refer to “To adjust color gradation
automatically” on page 10.
• Wait 30 minutes or more from
monitor power on before starting the
color adjustment.
• Choose “Reset” in the <Color> menu
to revert to the default settings (factory
settings) of hue of the color mode
selected.
• The same image may be seen in
different colors on multiple monitors
due to their monitor-specific
characteristics. Make fine color
adjustment visually when matching
colors on multiple monitors.
●
To select an appropriate mode for images
: Adjustment available −: Invalid for adjustment
✓
FineContrast mode
Icon
Function
Custom sRGB
Text
✓
✓
✓
✓
✓
−
Picture
Movie
✓
✓
−
*
Brightness
✓
✓
✓
✓
✓
✓
✓
✓
✓
−
−
−
−
−
−
✓
✓
✓
−
*
Temperature
*
Gamma
Saturation
Hue
✓
✓
−
✓
✓
−
Gain
6 Colors
Reset
−
−
−
✓
✓
✓
* These items can also be set or adjusted with the FineContrast menu.
Menu
Description
Adjustment range
0 to 100%
NOTE
Brightness To adjust the full screen
brightness as desired
• The Adjustment menu and the
FineContrast menu cannot be
displayed at the same time.
• Adjustable functions vary depending
on the type of FineContrast mode.
NOTE
• You can also adjust the brightness by pressing
button while the adjustment menu is not displayed. Press
after adjustment.
or
• The values shown in the “%” are available only as reference.
Temperature To select a color
4000K to 10000K in units of 500K
(including 9300K).
temperature
NOTE
• Setting the value to “Off” presents the natural color
temperature of the panel.
• The values shown in the Kelvin (K) are available only as
reference.
Gamma
To set a gamma value
1.4 to 3.0, Fixed
NOTE
• Digital signal input is recommended for gamma value setting.
Set a gamma value to 1.8 - 2.2 for analog signal input.
• Only when selecting “Custom” in the fine contrast mode,
“Fixed” is available.
Saturation To adjust color saturation
–100 to 100
Setting the minimum (–100) turns
the image to a monochrome
screen.
Attention
• This function does not enable to display every color gradation.
Hue
To produce a desired skin
color, etc.
–100 to 100
Attention
• This function does not enable to display every color gradation.
Chapter 2 Settings and Adjustments
12
Menu
Description
Adjustment range
0 to 100%
Gain
To adjust red, green, and
blue to a desired color tone Adjust the respective brightness of
respectively
red/green/blue to make a desired
color tone. Display an image with
white or gray background for
adjustment.
NOTE
• The values shown in the “%” are available only as reference.
• When using the <Gain> setting, the <Temperature> setting is
set to “Off.”
6 Colors
Reset
To adjust <Hue> and
<Saturation> in Red,
Yellow, Green, Cyan, Blue,
and Magenta respectively
Hue: –100 to 100
Saturation: –100 to 100
To reset the color settings of the selected FineContrast mode to
the default settings
●
To set/adjust color
(1) Choose <Color> from the Adjustment menu, and press
(2) Select a desired function with from the <Color> menu,
and press
.
/
/
/
.
The selected function menu appears.
(3) Adjust the selected item with
The adjustment is completed.
/
/
/
, and press
.
Chapter 2 Settings and Adjustments
13
2-4 Off Timer/Power Saving Settings
●
To set monitor power-off time [Off Timer]
This function allows the monitor to automatically turn off after a specified time
has passed. This function serves to reduce afterimages caused when the monitor
screen is left on for a long time period without use. Use this function when an
image is displayed throughout the day.
Attention
• The Off Timer functions even in the
power saving mode, but the advance
notice is disabled. The monitor power
is turned off without advance notice.
[Off Timer System]
Timer
Monitor
Operating
Power Indicator
Blue
ON time (1H - 23H)
*
Last 15 min. in “ON time” Advance Notice
Flashing blue
Off
“ON time” expired
Power Off
*
When
is pressed during the advance notice period, the monitor continues to operate for
additional 90 minutes. Extension of operation time can be set without limitation.
[Procedure]
(1) Choose <Others> from the Adjustment menu, and press
(2) Choose <Off Timer> from the <Others> menu, and press
The <Off Timer> menu appears.
.
.
(3) Select “Enable” with
or
.
(4) Set a monitor ON time (1 to 23 hours) with
The Off Timer setting is completed.
or
, and press
.
[Resumption Procedure]
• Press
.
Chapter 2 Settings and Adjustments
14
●
To set monitor power-saving [VESA DPMS/DVI DMPM]
Analog input
■
This monitor complies with the VESA DPMS standard.
Attention
[Power Saving System]
• Unplugging the power cord
completely shuts off power supply to
the monitor.
• USB compliant devices connected
to the monitor work even if the
monitor is in the power saving mode.
Therefore, power consumption of the
monitor varies with connected devices
even in the power saving mode.
Power
Indicator
PC
Monitor
Operating
Operating
Power saving
Blue
Orange
Power saving
STAND-BY
SUSPENDED
OFF
[Procedure]
(1) Choose <PowerManager> from the Adjustment menu, and press
The set menu appears.
.
(2) Select “VESA DPMS” with
or
, and press
.
The power saving setting is completed.
[Resumption Procedure]
• Operate the mouse or keyboard to resume the normal screen.
■
Digital input
This monitor complies with the DVI DMPM standard.
[Power Saving System]
The monitor enters the power saving mode in five seconds in connection with
the PC setting.
PC
Monitor
Operating
Power saving
Power Indicator
Blue
Orange
Operating
Power saving
[Procedure]
(1) Choose <PowerManager> from the Adjustment menu, and press
The set menu appears.
.
(2) Select “DVI DMPM” with
or
, and press
.
The power saving setting is completed.
[Resumption Procedure]
• Operate the mouse or keyboard to resume the normal screen.
Chapter 2 Settings and Adjustments
15
2-5 Screen Size Selection
●
To change screen size [Screen Size]
The image with the resolution other than the recommended resolution is
displayed in full screen automatically. You can change the screen size by using
<Screen Size> from <Others> menu.
Menu
Full Screen
Function
Displays an image in full screen. Images are distorted in
some cases because the vertical rate is not equal to the
horizontal rate.
(default setting)
Displays an image in full screen. In some cases, a blank
horizontal or vertical border appears to equalize the
vertical rate and the horizontal rate.
Enlarged
Normal
Displays images with the specified resolution.
Example: Image size 1280 × 1024
Full Screen
(Default setting)
Enlarged
Normal
(1920 × 1200)
(1500 × 1200)
(1280 × 1024)
[Procedure]
(1) Choose <Others> from the Adjustment menu, and press
(2) Choose <Screen Size> from the <Others> menu, and press
The screen size setting window appears.
.
.
(3) Select “Full Screen,” “Enlarged,” or “Normal” with
press
or
, and
.
The screen size setting is completed.
●
To adjust brightness of non-display area [Border Intensity]
A border (black area with no image) around the image appears in the “Normal”
or “Enlarged” mode.
Border
(1) Choose <Others> from the Adjustment menu, and press
.
(2) Choose <Border Intensity> from the <Others> menu, and press
The <Border Intensity> menu appears.
.
(3) Adjust border intensity with
or
, and press
.
The border intensity adjustment is completed.
Chapter 2 Settings and Adjustments
16
2-6 Power Indicator/EIZO Logo Display
Setting
NOTE
●
To turn off the Power indicator while a screen is displayed
[Power Indicator]
• The Power indicator lights up at
power on with the default setting.
This function enables to turn off the Power indicator (blue) while a screen is
displayed.
(1) Choose <Others> from the Adjustment menu, and press
.
(2) Choose <Power Indicator> from the <Others> menu, and press
The <Power Indicator> menu appears.
.
(3) Select “Disable” with
or
, and press
.
The Power Indicator setting is completed.
NOTE
●
To display EIZO logo [EIZO Logo Appearing Function]
• The logo appears with the default
setting.
When this unit is turned on, the EIZO logo appears at the center of the screen.
Selection to display or not to display the logo is available with this function.
(1) Press
(2) Press
to turn off the unit.
again while pressing
to turn on the unit.
The EIZO Logo display/non-display function is toggled.
2-7 Beeper Settings
●
To set the beeper [Beep]
Set the beeper on/off for operation tone of the switches, connection error, etc.
Sound type
Short beep
Conditions for beeping
• When an item is selected with
• When a maximum or minimum value is set with
/
/
/
• When
is pressed
Long beep
• When
is pressed
• When registration is performed with
Consecutive beeps
• When the monitor is not connected correctly
• When the PC is not turned on
• When a frequency out of the specified range is
received
Beep-beep once every 15 • 15 minutes before the power off time set by “Off
seconds
Timer” (advance notice time)
(1) Choose <Others> from the Adjustment menu, and press
(2) Choose <Beep> from the <Others> menu, and press
The <Beep> menu appears.
.
.
(3) Select “On” or “Off” with
The beep setting is completed.
or
, and press
.
Chapter 2 Settings and Adjustments
17
2-8 Locking Buttons
●
To lock operation [Adjustment Lock]
This function locks the buttons to retain the status adjusted or set once.
Buttons that can be
locked
•
•
•
•
(Enter button)
(Auto button)
(Mode button)
/
/
/
/ (Control buttons)
Buttons that cannot
be locked
•
•
•
(Power button)
(Input signal selection)
(Adjustment Lock button)
(1) Press
for more than two seconds.
The adjustment lock setting is completed.
[Unlocking]
(1) Press again for more than two seconds.
The adjustment lock is released.
2-9 Setting Adjustment Menu Display
●
To update menu settings [Menu Size/Menu Position/Menu
Off Timer/Translucent]
Menu Size
Change the Adjustment menu size using the following procedure.
(1) Choose <Others> from the Adjustment menu, and press
.
(2) Choose <Menu Settings> from the <Others> menu, and press
.
(3) Choose <Menu Size> from the <Menu Settings> menu, and press
The <Menu Size> menu appears.
.
(4) Select “Enlarged” using
or
, and press
.
The menu size setting is completed.
Menu Position
Adjust the menu position using the following procedure.
(1) Choose <Others> from the Adjustment menu, and press
.
(2) Choose <Menu Settings> from the <Others> menu, and press
.
(3) Choose <Menu Position> from the <Menu Settings> menu, and press
The <Menu Position> menu appears.
.
(4) Select a menu position with
/
/
/
, and press
.
The menu position setting is completed.
Menu Off Timer
NOTE
Set the menu display time using the following procedure.
• The display time of the FineContrast
mode remains unchanged.
(1) Choose <Others> from the Adjustment menu, and press
.
(2) Choose <Menu Settings> from the <Others> menu, and press
.
(3) Choose <Menu Off Timer> from the <Menu Settings> menu, and press
The <Menu Off Timer> menu appears.
.
(4) Select “Enable” with
or
.
(5) Choose an Off Time (15/30/45/60 seconds) with
The menu off timer setting is completed.
or
, and press
.
Chapter 2 Settings and Adjustments
18
Translucent
Set the transparency for menu display using the following procedure.
(1) Choose <Others> from the Adjustment menu, and press
.
(2) Choose <Menu Settings> from the <Others> menu, and press
.
(3) Choose <Translucent> from the <Menu Settings> menu, and press
The <Translucent> menu appears.
.
(4) Adjust the transparency for menu display with
The transparency setting is completed.
or
, and press
.
2-10 Setting Orientation
NOTE
●
To set the orientation of the Adjustment menu [Orientation]
• If you use the monitor with “Portrait”
position, the setting may be required
to change depending on the graphics
board used in your PC. Refer to the
manual of the graphics board for
details.
This function allows you to change the orientation of the Adjustment menu
when using the monitor screen in vertical display position.
(1) Choose <Others> from the Adjustment menu, and press
.
(2) Choose <Menu Settings> from the <Others> menu, and press
.
(3) Choose <Orientation> from the <Menu Settings> menu, and press
The <Orientation> menu appears.
.
(4) Select “Portrait” with
or
, and press
.
The orientation setting is completed.
(5) Turn the monitor screen 90° in clockwise direction.
2-11 Viewing Information/Setting Language
NOTE
●
To check settings, usage time, etc. [Information]
• The usage time is not always “0”
when you purchase the monitor due
to factory inspection.
This function allows you to check settings, model name, serial number, and
usage time of the monitor.
(1) Choose <Information> from the Adjustment menu, and press
The <Information> menu appears.
.
(2) Then, press
to check settings, etc.
●
To set a language to be displayed [Language]
This function allows to select the Adjustment menu language.
Selectable languages
English/German/French/Spanish/Italian/Swedish/Simplified Chinese/
Traditional Chinese/Japanese
(1) Choose <Language> menu from the Adjustment menu, and press
The <Language> menu appears.
.
(2) Choose a language with
/
/
/
, and press
.
The language setting is completed.
Chapter 2 Settings and Adjustments
19
2-12 Setting BrightRegulator
NOTE
●
To set automatic brightness adjustment [BrightRegulator]
• Be careful not to block the sensor on
the lower side of the monitor when
using the BrightRegulator function.
The sensor on the front side of the monitor detects the environmental brightness
to adjust the screen brightness automatically and comfortably.
(1) Choose <Others> from the Adjustment menu, and press
.
(2) Choose < BrightRegulator> from the <Others> menu, and press
The BrightRegulator setting window appears.
.
(3) Select “Enable” or “Disable” with
The BrightRegulator setting is completed.
or
, and press
.
2-13 Resumption of Default Setting
●
NOTE
To reset color adjustment [Reset]
• For main default settings, refer
to “Main default settings (factory
settings)” on page 30.
The hue in the color mode currently set will revert to the default settings (factory
settings).
(1) Choose <Color> from the Adjustment menu, and press
(2) Choose <Reset> from the <Color> menu and press
The <Reset> menu appears.
.
.
(3) Select <Reset> with
or
, and press
.
The reset operation is completed.
●
To reset all settings [Reset]
Reset all adjustments/settings to the factory default settings.
(1) Choose <Others> from the Adjustment menu, and press
(2) Choose <Reset> from the <Others> menu, and press
The <Reset> menu appears.
.
.
(3) Select <Reset> with
or
, and press
.
The reset operation is completed.
Chapter 2 Settings and Adjustments
20
Chapter 3 Connecting Cables
3-1 Connecting Two PCs to the Monitor
Two PCs can be connected to the monitor through the DVI-I connector on the
back of the monitor.
Connection examples
DVI-I
DVI-I
connector connector
(Signal 1) (Signal 2)
PC 1
PC 2
DVI
Signal cable
(supplied FD-C39)
Signal cable
(supplied FD-C16) 15-pin
D-sub mini
D-sub mini Signal cable
Signal cable
(supplied FD-C16) 15-pin
D-sub mini
15-pin
(FD-C16 option)
DVI
Signal Cable
(FD-C39 option)
Signal cable
(supplied FD-C39)
DVI
Selecting input signal
Input Signal Selection button
Switch the input signal with
. Input signal switches each time
is pressed.
When the signal is switched, the active signal type (Signal 1 or 2/Analog or
Digital) appears at the top right corner of the screen.
Chapter 3 Connecting Cables
21
●
NOTE
To set priority of PC to be displayed [Input Priority]
• Power-saving function
When two PCs are connected, either one can be displayed preferentially. The
monitor senses the input signal regularly. When the signal that is given priority
with the <Input Priority> setting is input, signal input switches automatically to
the prior signal.
When “1” or “2” is selected for
<Input Priority>, the monitor’s
power-saving function works only
when the two PCs are in the power-
saving mode.
Priority setting
Function
• When only one PC is connected, the
input signal is detected automatically
regardless of whether the input signal
1 or 2 has priority.
1
The input signal from “Signal 1” is displayed in the
following cases.
• When the monitor is turned on.
Input from Signal 1
• When the PC for the “Signal 1” is turned on while
displaying the image of the “Signal 2”.
• When the PC for the “Signal 1” is recovered from
the Power saving mode while displaying the
image of the “Signal 2”.
2
The input signal from “Signal 2” is displayed in the
following cases.
• When the monitor is turned on.
Input from Signal 2
• When the PC for the “Signal 2” is turned on while
displaying the image of the “Signal 1”.
• When the PC for the “Signal 2” is recovered from
the Power saving mode while displaying the
image of the “Signal 1”.
Manual
The monitor does not detect the PC’s signals
automatically. Select an active input signal with
.
[Procedure]
(1) Choose <Others> from the Adjustment menu, and press
.
(2) Choose <Input Priority> from the <Others> menu, and press
The <Input Priority> menu appears.
.
(3) Select “1” or “2” or “Manual” with
The Input Priority setting is completed.
or
, and press
.
Chapter 3 Connecting Cables
22
Attention
3-2 Connecting Peripheral USB Devices
This monitor has a hub compatible with USB. Connected to a PC compatible
with USB or another USB hub, this monitor functions as a USB hub allowing
connection to peripheral USB devices.
• This monitor may not work depending
on PC, OS or peripheral devices to be
used.
For USB compatibility of peripheral
devices, contact their manufactures.
• If the monitor is in the power saving
mode, or if the monitor is connected
to the power outlet with the monitor
turned off, all the devices connected
to the USB ports (upstream and
downstream) work. Therefore, power
consumption of the monitor varies
with connected devices even in the
power saving mode.
● Required System Environment
(1) A PC equipped with a USB port or another USB hub connected to
a USB compatible PC
(2) Windows 2000/XP/Vista or Mac OS 9.2.2 and Mac OS X 10.2 or
later
(3) EIZO USB cable (MD-C93)
● Connection Procedure (Setup of USB Function)
(1) Connect the monitor first to a PC using the signal cable, and run
the PC.
(2) Connect the supplied USB cable between the downstream USB
port of a USB compatible PC (or another USB hub) and the
monitor’s upstream USB port.
(3) When the USB function setup is completed, the monitor functions
as a USB hub allowing connection to various peripheral USB
devices through its downstream USB ports.
SX2461W
Upstream
Downstream
SX2761W
Downstream
Upstream
The USB function is set up automatically upon connection of the
USB cable.
Chapter 3 Connecting Cables
23
Chapter 4 Troubleshooting
If a problem still remains after applying the suggested remedies, contact your local dealer.
• No-picture problems → See No.1 - No.2.
• Imaging problems (digital input) → See No.3 - No.8.
• Imaging problems (analog input) → See No.3 - No.13.
• Other problems → See No.14 - No.17.
• USB problems → See No.18.
Problems
Possible cause and remedy
1. No picture
• Power indicator does not light.
• Check whether the power cord is connected correctly. If
the problem persists, turn off the monitor, and then turn it
on again a few minutes later.
• Press
.
• Power indicator is lighting blue.
• Power indicator is lighting orange.
• Set each RGB adjusting value in <Gain> to higher level.
(see page 13)
• Switch the input signal with
.
• Operate the mouse or keyboard.
• Check whether the PC is turned on.
2. The message below appears.
This message appears when the signal is not input
correctly even when the monitor functions properly.
• This message appears when no signal is input.
• The message shown left may appear, because some
PCs do not output the signal soon after power-on.
• Check whether the PC is turned on.
• Check whether the signal cable is connected properly.
• Switch the input signal with
.
• The message below shows that the input signal is
out of the specified frequency range. (Such signal
frequency is displayed in red.)
• Reboot the PC.
• Select an appropriate display mode using the graphics
board’s utility. Refer to the manual of the graphics board
for details.
Example:
3. The screen is too bright or too dark.
• Adjust <Brightness>. (The LCD monitor backlight has a
fixed life span. When the screen becomes dark or begins
to flicker, contact your local dealer.)
4. Characters are blurred.
5. Afterimages appear.
• Adjust using <Smoothing>. (see page 10)
• Use a screen saver or off timer function for a long-time
image display.
• Afterimages are particular to LCD monitors. Avoid
displaying the same image for a long time.
6. Green/red/blue/white dots or defective dots remain • This is due to LCD panel characteristics and is not a
on the screen. failure.
7. Interference patterns or pressure marks remain on • Leave the monitor with a white or black screen. The
the screen.
symptom may disappear.
8. Noise appears on the screen.
• When entering the signals of analog input, select 1 to 4
in <Signal Filter> from the <Screen> menu to change the
mode.
• When entering the signals of HDCP system, the normal
images may not be displayed immediately.
Chapter 4 Troubleshooting
24
Problems
Possible cause and remedy
9. Display position is incorrect.
• Adjust image position so that it is displayed properly
within the display area using the <Position> adjustment.
(See page 9)
• If the problem persists, use the graphics board’s utility if
available to change the display position.
10. Screen image displayed is smaller or larger than
the actual screen image.
• Adjust the resolution using <Resolution> so that the input
signal resolution equals the resolution in the resolution
adjustment menu. (see page 10)
11. Vertical bars appear on the screen or a part of the • Adjust using <Clock>. (see page 9)
image is flickering.
12. Whole screen is flickering or blurring.
• Adjust using <Phase>. (see page 9)
13. Upper part of the screen is distorted as shown
below.
• This is caused when both composite sync (X-OR)
signal and separate vertical sync signal are input
simultaneously. Select either composite signal or
separate signal.
14. The <Smoothing> icon on the Adjustment menu
<Screen> cannot be selected.
• Smoothing setting may not be required depending on the
display resolution. (You cannot choose the smoothing
icon.)
• <Smoothing> is disabled when the screen is displayed in
the following resolutions.
• 1920 × 1200
• Select [Enlarged] during <Screen Size> in the
resolution of 1600 × 1200
• Select [Normal] during <Screen Size>.
15. The Main menu of Adjustment menu does not start. • Check for Adjustment Lock function. (see page 18)
16. The FineContrast menu is not displayed.
• Check whether the Main menu of Adjustment menu is
displayed. (Refer to “Advanced Adjustments [Adjustment
menu]” on page 12.)
• Check for Adjustment Lock function. (see page 18)
17. The auto-adjustment function does not work
correctly.
• This function does not work when digital signal is input.
• Check for Adjustment Lock function. (see page 18)
• This function does not work correctly with some graphics
boards.
18. The monitor connected with the USB cable is not
• Check whether the USB cable is connected correctly.
detected. / USB devices connected to the monitor • Change the USB port to another one. If the PC or
does not work.
peripheral devices works correctly by changing the USB
port, contact your local dealer. (Refer to the manual of
the PC for details.)
• Please perform the followings to check the status.
• Reboot the PC.
• Connect the PC and peripheral devices directly.
• If the PC or peripheral devices works correctly without
connecting each other via the monitor (working as a USB
hub), please contact your local dealer.
• Check whether the PC and OS are USB compliant. (For
USB compliance of the respective devices, consult their
manufacturers.)
• Check the PC’s BIOS setting for USB when using
Windows. (Refer to the manual of the PC for details.)
Chapter 4 Troubleshooting
25
Chapter 5 Reference
5-1 Attaching an Arm
Attention
The stand can be removed and replaced with an arm (or another stand) to be
attached to the monitor. Use an arm or stand of EIZO option.
• When attaching an arm or stand,
follow the instructions of their user’s
manual.
• When using another manufacturer’
s arm or stand, confirm the following
in advance and select one conforming
to the VESA standard. Use the M4
× 12 mm screws supplied with this
monitor.
[Attaching]
Lay the LCD monitor on a soft cloth spread over on a stable
1
surface with the panel surface facing down.
Remove the stand. (Prepare a screwdriver.)
2
– Clearance between the screw holes:
100 mm × 100 mm
Unscrew the four screws securing the unit and the stand with the
screwdriver.
– Thickness of plate: 2.6 mm
– Strong enough to support weight of
the monitor unit (except the stand)
and attachments such as cables.
• When using an arm or stand, attach it
to meet the following tilt angles of the
monitor.
Attach the monitor to the arm or stand.
3
Secure the monitor to the arm or stand using the screws specified in the
user’s manual of the arm or stand.
– Up 45 degrees, down 45 degrees
(horizontal display, and vertical
display rotated 90 degrees
clockwise)
• Connect the cables after attaching an
arm.
Chapter 5 Reference
26
Attention
5-2 Cleaning
• Never use any solvents or chemicals,
such as thinner, benzene, wax,
alcohol, and abrasive cleaner, which
may damage the cabinet or LCD
panel.
Clean the monitor periodically to keep the monitor clean and extend its life.
Cabinet
Clean the cabinet with a soft cloth dampened with little mild detergent.
LCD Panel
• Clean the LCD panel with a soft cloth such as cotton cloth or lens cleaning
paper.
NOTE
• Optional ScreenCleaner is
recommended for cleaning the LCD
panel surface.
• Remove persistent stains gently with a cloth dampened with little water, and
then clean the LCD panel again with a dry cloth for better finishing.
Chapter 5 Reference
27
5-3 Specifications
SX2461W
LCD Panel
24.1-inch (610 mm) TFT color LCD with anti-glare hard coating
Viewing angle: Horizontal 178°, Vertical 178° (CR:10 or more)
Dot Pitch
0.270mm
Horizontal Scan Frequency
Analog: 24-94kHz
Digital: 31-76kHz
Vertical Scan Frequency
Analog: 49-86Hz (Non-interlace)
(1600 × 1200: 49-76Hz)
(1920 × 1200: 49-61Hz)
Digital: 59-61Hz (Non-interlace)
(VGA TEXT: 69-71Hz)
Resolution
1920 dots × 1200 lines
Max. Dot Clock
Analog: 202.5MHz
Digital: 162MHz
Max. Display Color
Display Area (H × V)
Power Supply
Approx. 16.77 million colors
518.4mm × 324.0mm
100-120 VAC ±10%, 50/60Hz 1.1A
200-240 VAC ±10%, 50/60Hz 0.55A
Power
Consumption
Screen Display On 110W or less (with USB load)
100W or less (without USB load)
Power saving mode 2W or less (for single signal input, without USB load)
Power button Off
1W or less (without USB load)
DVI-I connector (Applicable to HDCP) × 2
Separate, TTL, positive/ negative
Composite, TTL, positive/ negative
Analog, Positive (0.7Vp-p/75Ω)
TMDS (Single Link)
Input Signal Connector
Analog Input Signal (Sync)
Analog Input Signal (Video)
Digital Signal Transmission System
Video Signal Memory
Analog signal: 45 (preset: 30)
Digital signal: 10 (preset: 0)
Plug & Play
VESA DDC 2B / EDID structure 1.3
Dimensions
Main unit (including 566mm(22.3) × 456 - 538mm(18.0 - 21.2) × 230mm(9.1)
(Width) × (Height) × Height adjustable
(Depth) mm (inch) stand)
Main unit (without
stand)
566mm(22.3) × 367mm(14.4) × 85mm(3.3)
Mass
Main unit (including 11.0 kg (24.3 lbs.)
Height adjustable
stand)
Main unit (without
stand)
7.4 kg (16.3 lbs.)
Movable range
Tilt
40° Up, 0° Down
35° Right, 35° Left
82 mm (3.2 inch)
90°
Swivel
Adjustable height
Rotation
Environmental
Conditions
Temperature
Operating temperature: 0 °C - 35 °C (32 °F - 95 °F)
Storage temperature: -20 °C - 60 °C (-4 °F - 140 °F)
Humidity
Relative humidity: 30% - 80% (no condensation)
Chapter 5 Reference
28
USB
Standard
Port
USB Specification Revision 2.0
Upstream port × 1, Downstream port × 2
Downstream: Max. 500mA/1 port
Supply current
SX2761W
LCD Panel
27.0-inch (690 mm) TFT color LCD with anti-glare hard coating
Viewing angle: Horizontal 178°, Vertical 178° (CR:10 or more)
Dot Pitch
0.303mm
Horizontal Scan Frequency
Analog: 24-94kHz
Digital: 31-76kHz
Vertical Scan Frequency
Analog: 49-86Hz (Non-interlace)
(1600 × 1200: 49-76Hz)
(1920 × 1200: 49-61Hz)
Digital: 59-61Hz (Non-interlace)
(VGA TEXT: 69-71Hz)
Resolution
1920 dots × 1200 lines
Max. Dot Clock
Analog: 202.5MHz
Digital: 162MHz
Max. Display Color
Display Area (H × V)
Power Supply
Approx. 16.77 million colors
581.76mm × 363.6mm
100-120 VAC ±10%, 50/60Hz 1.1A
200-240 VAC ±10%, 50/60Hz 0.6A
Power
Consumption
Screen Display On 115W or less (with USB load)
110W or less (without USB load)
Power saving mode 1.7W or less (for single signal input, without USB load)
Power button Off
0.9W or less (without USB load)
DVI-I connector (Applicable to HDCP) × 2
Separate, TTL, positive/ negative
Composite, TTL, positive/ negative
Analog, Positive (0.7Vp-p/75Ω)
TMDS (Single Link)
Input Signal Connector
Analog Input Signal (Sync)
Analog Input Signal (Video)
Digital Signal Transmission System
Video Signal Memory
Analog signal: 45 (preset: 30)
Digital signal: 10 (preset: 0)
Plug & Play
VESA DDC 2B / EDID structure 1.3
Dimensions
Main unit (including 630mm(24.8) × 492.5 - 610.5mm(19.4 - 24.0) × 254.7mm(10.0)
(Width) × (Height) × Height adjustable
(Depth) mm (inch) stand)
Main unit (without
stand)
630mm(24.8) × 412mm(16.2) × 86mm(3.4)
Mass
Main unit (including 13.2 kg (29.1 lbs.)
Height adjustable
stand)
Main unit (without
stand)
8.7 kg (19.2 lbs.)
Movable range
Tilt
40° Up, 0° Down
35° Right, 35° Left
118 mm (4.6 inch)
90°
Swivel
Adjustable height
Rotation
Chapter 5 Reference
29
Environmental
Conditions
Temperature
Operating temperature: 0 °C - 35 °C (32 °F - 95 °F)
Storage temperature: -20 °C - 60 °C (-4 °F - 140 °F)
Humidity
Standard
Port
Relative humidity: 30% - 80% (no condensation)
USB Specification Revision 2.0
USB
Upstream port × 1, Downstream port × 2
Downstream: Max. 500mA/1 port
Supply current
Main default settings (factory settings)
BrightRegulator
Disable
Smoothing
3
FineContrast Mode
Custom
PowerManager
VESA DPMS (Analog Input)
DVI DMPM (Digital Input)
Screen Size
Beep
Full Screen
On
Off Timer
Disable
Normal
Menu Settings
Menu Size
Menu Off Timer
45 sec
1
Input Priority
Language
English
Chapter 5 Reference
30
Outside Dimensions
SX2461W
190(7.5)
unit : mm (inch)
SWIVEL
566(22.3)
520.4(20.5)
TILT
85(3.35)
56.3
(2.22)
532(20.9)
100(3.9)
233(9.2)
233(9.2)
33(1.3)
398.5(15.7)
230(9.1)
Outside Dimensions
SX2761W
240(9.4)
unit : mm (inch)
SWIVEL
630(24.8)
587.2(23.1)
TILT
86(3.39)
51(2.0)
596(23.5)
100(3.9)
265(10.4)
265(10.4)
52(2.05)
405.6(16.0)
254.7(10.0)
Chapter 5 Reference
31
Connector Pin Assignment
• DVI-I connector
3
1
9
17
2
4
12
20
6
7
8
16
24
5
13
21
C1 C2
10 11
19
14 15
22 23
C3 C4
C5
18
Pin No.
Signal
Pin No.
11
Signal
T.M.D.S. Data1/3 Shield
NC*
Pin No.
21 NC*
Signal
1
2
3
4
5
T.M.D.S. Data 2-
T.M.D.S. Data 2+
T.M.D.S. Data2/4 Shield
NC*
12
22
T.M.D.S. Clock shield
T.M.D.S. Clock+
T.M.D.S. Clock-
Analog Red
13
NC*
23
14
+5V Power
24
NC*
15
Ground (return for +5V,
Hsync and Vsync)
C1
6
7
8
9
DDC Clock (SCL)
DDC Data (SDA)
Analog Vertical Sync
T.M.D.S. Data1-
16
17
18
19
Hot Plug Detect
C2
C3
C4
C5
Analog Green
T.M.D.S. Data0-
Analog Blue
T.M.D.S. Data0+
T.M.D.S. Data0/5 Shield
Analog Horizontal Sync
Analog Ground (analog
R,G,&B return)
10
T.M.D.S. Data1+
20
NC*
(NC*: No Connection)
• USB port
Downstream
Upstream
Series B connector
Series A connector
Contact No.
Signal
Remarks
Cable power
Serial data
1
2
3
4
VCC
– Data
+ Data
Ground
Serial data
Cable ground
Option List
Cleaning Kit
EIZO ScreenCleaner
FD-C16
FD-C39
Signal Cable
Speaker Unit
i•Sound L3
Chapter 5 Reference
32
5-4 Glossary
Clock
The analog input monitor needs to reproduce a clock of the same frequency as the dot clock of the graphics system in
use, when the analog input signal is converted to a digital signal for image display.
This is called clock adjustment. If the clock pulse is not set correctly, some vertical bars appear on the screen.
DVI (Digital Visual Interface)
DVI is a digital interface standard. DVI allows direct transmission of the PC’s digital data without loss.
This adopts the TMDS transmission system and DVI connectors. There are two types of DVI connectors. One is
a DVI-D connector for digital signal input only. The other is a DVI-I connector for both digital and analog signal
inputs.
DVI DMPM (DVI Digital Monitor Power Management)
DVI DMPM is a digital interface power-saving function. The “Monitor ON (operating mode)” and “Active Off
(power-saving mode)” are indispensable for DVI DMPM as the monitor’s power mode.
Gain
This is used to adjust each color parameter for red, green and blue. An LCD monitor displays the color by the light
passing through the panel color filter. Red, green and blue are the three primary colors. All the colors on the screen
are displayed by combining these three colors. The color tone can be changed by adjusting the light intensity (volume)
passing through each color’s filter.
Gamma
Generally, the monitor brightness varies nonlinearly with the input signal level, which is called “Gamma
Characteristic”. A small gamma value produces a low-contrast image, while a large gamma value produces a high-
contrast image.
HDCP (High-bandwidth Digital Contents Protection)
Digital signal coding system developed to copy-protect the digital contents, such as video, music, etc. This helps
to transmit the digital contents safely by coding the digital contents sent via DVI terminal on the output side and
decoding them on the input side.
Any digital contents cannot be reproduced if both of the equipments on the output and input sides are not applicable
to HDCP system.
Phase
Phase means the sampling timing to convert the analog input signal to a digital signal. Phase adjustment is made to
adjust the timing. It is recommended that phase adjustment be made after the clock is adjusted correctly.
Range Adjustment
Range adjustment controls the signal output levels to display every color gradation. It is recommended that range
adjustment be made before color adjustment.
Resolution
The LCD panel consists of numerous pixels of specified size, which are illuminated to form images. This monitor
consists of 1920 horizontal pixels and 1200 vertical pixels. At a resolution of 1920 × 1200, all pixels are illuminated
as a full screen (1:1).
sRGB (Standard RGB)
International standard for “color reproduction and color space” among peripheral devices (such as monitors, printers,
digital cameras, scanners). sRGB allows Internet users to closely match colors as a simple color matching means for
the Internet use.
Chapter 5 Reference
33
Temperature
Color temperature is a method to measure the white color tone, generally indicated in degrees Kelvin. The screen
becomes reddish at a low temperature, and bluish at a high temperature, like the flame temperature.
5000K: Slightly reddish white
6500K: Warm white like paper white
9300K: Slightly bluish white
TMDS (Transition Minimized Differential Signaling)
A signal transmission system for digital interface.
VESA DPMS (Video Electronics Standards Association - Display Power Management Signaling)
VESA provides the standardization of signals from PC (graphics board) for power saving of PC monitors. DPMS
defines the signal status between PC and monitor.
Chapter 5 Reference
34
5-5 Preset Timing
The following table shows factory preset video timing (for analog signal only).
Attention
• Display position may be deviated
depending on the PC connected,
which may require screen adjustment
using Adjustment menu.
Frequency
Horizontal: kHz
Vertical: Hz
Mode
Dot clock
Polarity
Horizontal
Vertical
31.47
59.94
31.47
70.09
35.00
66.67
49.72
74.55
68.68
75.06
74.76
74.76
37.86
72.81
37.50
75.00
43.27
85.01
35.16
56.25
37.88
60.32
48.08
72.19
46.88
75.00
53.67
85.06
48.36
60.00
56.48
70.07
60.02
75.03
68.68
85.00
67.50
75.00
60.00
60.00
63.98
60.02
79.98
75.03
91.15
85.03
75.00
60.00
81.30
65.00
Negative
Negative
Negative
Positive
Negative
Negative
Negative
Negative
Negative
Negative
Positive
Positive
Negative
Negative
Negative
Negative
Negative
Negative
Positive
Positive
Positive
Positive
Positive
Positive
Positive
Positive
Positive
Positive
Negative
Negative
Negative
Negative
Positive
Positive
Positive
Positive
Positive
Positive
Positive
Positive
Positive
Positive
Positive
Positive
Positive
Positive
Positive
Positive
Positive
Positive
• If a signal other than those listed in
the table is input, adjust the screen
using the Adjustment menu. However,
screen display may still be incorrect
even after the adjustment.
• When interlace signals are used, the
screen cannot be displayed correctly
even after screen adjustment using the
Adjustment menu.
VGA 640×480@60Hz
VGA 720×400@70Hz
25.2 MHz
28.3 MHz
30.2 MHz
57.3 MHz
100.0 MHz
126.2 MHz
31.5 MHz
31.5 MHz
36.0 MHz
36.0 MHz
40.0 MHz
50.0 MHz
49.5 MHz
56.3 MHz
65.0 MHz
75.0 MHz
78.8 MHz
94.5 MHz
108.0 MHz
108.0 MHz
Horizontal
Vertical
Horizontal
Vertical
Macintosh
640×480@67Hz
Horizontal
Vertical
Macintosh
832×624@75Hz
Horizontal
Vertical
Macintosh
1152×870@75Hz
Horizontal
Vertical
Macintosh
1280×960@75Hz
Horizontal
Vertical
VESA 640×480@72Hz
VESA 640×480@75Hz
VESA 640×480@85Hz
VESA 800×600@56Hz
VESA 800×600@60Hz
VESA 800×600@72Hz
VESA 800×600@75Hz
VESA 800×600@85Hz
VESA 1024×768@60Hz
VESA 1024×768@70Hz
VESA 1024×768@75Hz
VESA 1024×768@85Hz
VESA 1152×864@75Hz
VESA 1280×960@60Hz
Horizontal
Vertical
Horizontal
Vertical
Horizontal
Vertical
Horizontal
Vertical
Horizontal
Vertical
Horizontal
Vertical
Horizontal
Vertical
Horizontal
Vertical
Horizontal
Vertical
Horizontal
Vertical
Horizontal
Vertical
Horizontal
Vertical
Horizontal
Vertical
Horizontal
Vertical
VESA 1280×1024@60Hz 108.0 MHz
VESA 1280×1024@75Hz 135.0 MHz
VESA 1280×1024@85Hz 157.5 MHz
VESA 1600×1200@60Hz 162.0 MHz
VESA 1600×1200@65Hz 175.0 MHz
Horizontal
Vertical
Horizontal
Vertical
Horizontal
Vertical
Horizontal
Vertical
Chapter 5 Reference
35
Frequency
Horizontal: kHz
Vertical: Hz
Mode
Dot clock
Polarity
Horizontal
Vertical
87.50
70.00
93.80
75.00
65.29
59.95
74.56
59.89
74.04
59.95
Positive
Positive
Positive
Positive
Negative
Positive
Negative
Positive
Positive
Negative
VESA 1600×1200@70Hz 189.0 MHz
VESA 1600×1200@75Hz 202.5 MHz
Horizontal
Vertical
Horizontal
Vertical
VESA CVT
1680×1050@60Hz
146.3 MHz
Horizontal
Vertical
VESA CVT 1920×1200
193.3 MHz
Horizontal
Vertical
VESA CVT RB 1920×1200 154.0 MHz
Chapter 5 Reference
36
For U.S.A. , Canada, etc. (rated 100-120 Vac) Only
FCC Declaration of Conformity
We, the Responsible Party
EIZO NANAO TECHNOLOGIES INC.
5710 Warland Drive, Cypress, CA 90630
Phone: (562) 431-5011
declare that the product
Trade name: EIZO
Model: FlexScan SX2461W/SX2761W
is in conformity with Part 15 of the FCC Rules. Operation of this product is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of the following measures.
* Reorient or relocate the receiving antenna.
* Increase the separation between the equipment and receiver.
* Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
* Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s
authority to operate the equipment.
Note
Use the attached specified cable below or EIZO signal cable with this monitor so as to keep interference within the
limits of a Class B digital device.
- AC Cord
- Shielded Signal Cable (enclosed)
Canadian Notice
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de le classe B est comforme à la norme NMB-003 du Canada.
Chapter 5 Reference
37
Hinweise zur Auswahl des richtigen Schwenkarms für Ihren Monitor
Dieser Monitor ist für Bildschirmarbeitsplätze vorgesehen. Wenn nicht der zum Standardzubehör gehörige
Schwenkarm verwendet wird, muss statt dessen ein geeigneter anderer Schwenkarm installiert werden. Bei der
Auswahl des Schwenkarms sind die nachstehenden Hinweise zu berücksichtigen:
Der Standfuß muß den nachfolgenden Anforderungen entsprechen:
a)Der Standfuß muß eine ausreichende mechanische Stabilität zur Aufnahme des Gewichtes vom Bildschirmgerät
und des spezifizierten Zubehörs besitzen. Das Gewicht des Bildschirmgerätes und des Zubehörs sind in der
zugehörenden Bedienungsanleitung angegeben.
b)Die Befestigung des Standfusses muß derart erfolgen, daß die oberste Zeile der Bildschirmanzeige nicht höher
als die Augenhöhe eines Benutzers in sitzender Position ist.
c)Im Fall eines stehenden Benutzers muß die Befestigung des Bildschirmgerätes derart erfolgen, daß die Höhe der
Bildschirmmitte über dem Boden zwischen 135 – 150 cm beträgt.
d)Der Standfuß muß die Möglichkeit zur Neigung des Bildschirmgerätes besitzen (max. vorwärts: 5°, min. nach
hinten ≥ 5°).
e)Der Standfuß muß die Möglichkeit zur Drehung des Bildschirmgerätes besitzen (max. ±180°). Der maximale
Kraftaufwand dafür muß weniger als 100 N betragen.
f) Der Standfuß muß in der Stellung verharren, in die er manuell bewegt wurde.
g)Der Glanzgrad des Standfusses muß weniger als 20 Glanzeinheiten betragen (seidenmatt).
h)Der Standfuß mit Bildschirmgerät muß bei einer Neigung von bis zu 10° aus der normalen aufrechten Position
kippsicher sein.
Hinweis zur Ergonomie :
Dieser Monitor erfüllt die Anforderungen an die Ergonomie nach EK1-ITB2000 mit dem Videosignal, 1920 ×
1200, Digital Eingang und mindestens 60,0 Hz Bildwiederholfrequenz, non interlaced. Weiterhin wird aus
ergonomischen Gründen empfohlen, die Grundfarbe Blau nicht auf dunklem Untergrund zu verwenden (schlechte
Erkennbarkeit, Augenbelastung bei zu geringem Zeichenkontrast.)
„Maschinenlärminformations-Verordnung 3. GPSGV:
Der höchste Schalldruckpegel beträgt 70 dB(A) oder weniger gemäss EN ISO 7779“
Chapter 5 Reference
38
|