Multimedia Projector
MODEL
LC-XS25
LC-XS30
Owner's Manual
To the Owner
Before operating this projector, read this manual
thoroughly and operate the projector properly.
This projector provides many convenient features and
functions. Operating the projector properly enables you to
manage those features and maintains it in better condition
for a considerable time.
Improper operation may result in not only shortening the
product-life, but also malfunctions, fire hazard, or other
accidents.
If your projector seems to operate improperly, read this
manual again, check operations and cable connections
and try the solutions in the "Troubleshooting" section on
pages 65-67 of this manual. If the problem still persists,
contact the dealer where you purchased the projector or
the service center.
Safety Precaution
WARNING: ● THIS APPARATUS MUST BE EARTHED.
● TO REDUCE THE RISK OF FIRE OR ELECTRIC
SHOCK, DO NOT EXPOSE THIS APPLIANCE TO
RAIN OR MOISTURE
– This projector produces intense light from the projection
lens. Do not stare directly into the lens, otherwise, eye
damage could result. Be especially careful that children
do not stare directly into the beam.
– Install the projector in a proper position. If not, it may
result in a fire hazard.
– Provide appropriate space on the top, sides and rear
of the projector cabinet for allowing air circulation
and cooling the projector. Minimum clearance must
be maintained. If the projector is to be built into a
compartment or similarly enclosed, the minimum
distances must be maintained. Do not cover the
ventilation slot on the projector. Heat build-up can
reduce the service life of your projector, and can also be
dangerous.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
SIDE and TOP
REAR
CAUTION:
TO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE COVER (OR
BACK) NO USER-SERVICEABLE PARTS
INSIDE EXCEPT LAMP REPLACEMENT
REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL
THIS SYMBOL INDICATES THAT DANGEROUS
VOLTAGE CONSTITUTING A RISK OF ELECTRIC
SHOCK IS PRESENT WITHIN THIS UNIT.
– If the projector is not to be used for an extended time,
unplug the projector from the power outlet.
THIS SYMBOL INDICATES THAT THERE ARE
IMPORTANT OPERATING AND MAINTENANCE
INSTRUCTIONS IN THE OWNER'S MANUAL WITH
THIS UNIT.
CAUTION
DO NOT SET THE PROjECTOR IN GREASy, WET, OR SMOKy
CONDITIONS SUCH AS IN
A
KITCHEN TO PREVENT
A
BREAKDOWN OR A DISASTER IF THE PROjECTOR COMES
IN CONTACT WITH OIL OR CHEMICALS, IT MAy BECOME
DETERIORATED
NOTE: This symbol and recycle system are applied to EU
countries only and not applied to the countries in the other
area of the world.
CAUTION
Your EIKI product is designed and
manufactured with high quality
materials and components which can
be recycled and reused.
Not for use in a computer room as defined in the Standard
for the Protection of Electronic Computer/Data Processing
Equipment, ANSI/NFPA 75.
This symbol means that electrical and
electronic equipment, at their end-of-
life, should be disposed of separately
from your household waste.
Ne peut être utilisé dans une salle d’ordinateurs telle
que définie dans la norme ANSI/NFPA 75 Standard
for Protection of Electronic Computer/Data Processing
Equipment.
Please dispose of this equipment at your local
community waste collection/recycling centre. In the
European Union there are separate collection systems
for used electrical and electronic products.
READ AND KEEP THIS OWNER'S MANUAL FOR LATER USE
Please help us to conserve the environment we live in!
4
Safety Instructions
All the safety and operating instructions should be read
before the product is operated.
This projector should be operated only from the type of
power source indicated on the marking label. If you are not
sure of the type of power supplied, consult your authorized
dealer or local power company.
Read all of the instructions given here and retain them
for later use. Unplug this projector from AC power supply
before cleaning. Do not use liquid or aerosol cleaners.
Use a damp cloth for cleaning.
Do not overload wall outlets and extension cords as this
can result in fire or electric shock. Do not allow anything to
rest on the power cord. Do not locate this projector where
the cord may be damaged by persons walking on it.
Follow all warnings and instructions marked on the
projector.
Do not attempt to service this projector yourself as opening
or removing covers may expose you to dangerous voltage
or other hazards. Refer all servicing to qualified service
personnel.
For added protection to the projector during a lightning
storm, or when it is left unattended and unused for long
periods of time, unplug it from the wall outlet. This will
prevent damage due to lightning and power line surges.
Unplug this projector from wall outlet and refer servicing to
qualified service personnel under the following conditions:
a.When the power cord or plug is damaged or frayed.
b.If liquid has been spilled into the projector.
Do not expose this unit to rain or use near water... for
example, in a wet basement, near a swimming pool, etc...
Do not use attachments not recommended by the
manufacturer as they may cause hazards.
c.If the projector has been exposed to rain or water.
d.If the projector does not operate normally by following
the operating instructions. Adjust only those controls that
are covered by the operating instructions as improper
adjustment of other controls may result in damage and
will often require extensive work by a qualified technician
to restore the projector to normal operation.
e.If the projector has been dropped or the cabinet has
been damaged.
f. When the projector exhibits a distinct change in
performance-this indicates a need for service.
Do not place this projector on an unstable cart, stand,
or table. The projector may fall, causing serious injury
to a child or adult, and serious damage to the projector.
Use only with a cart or stand recommended by the
manufacturer, or sold with the projector. Wall or shelf
mounting should follow the manufacturer's instructions,
and should use a mounting kit approved by the
manufacturers.
An appliance and cart combination
should be moved with care. Quick
stops, excessive force, and uneven
surfaces may cause the appliance and
cart combination to overturn.
When replacement parts are required, be sure the service
technician has used replacement parts specified by the
manufacturer that have the same characteristics as the
original part. Unauthorized substitutions may result in fire,
electric shock, or injury to persons.
Upon completion of any service or repairs to this projector,
ask the service technician to perform routine safety
checks to determine that the projector is in safe operating
condition.
Slots and openings in the back and bottom of the cabinet
are provided for ventilation, to ensure reliable operation of
the equipment and to protect it from overheating.
The openings should never be covered with cloth or other
materials, and the bottom opening should not be blocked
by placing the projector on a bed, sofa, rug, or other
similar surface. This projector should never be placed
near or over a radiator or heat register.
NOTE FOR CUSTOMERS INTHE US
Hg LAMP(S) INSIDE THIS PRODUCTCONTAIN MERCURY
AND MUST BE RECYCLED OR DISPOSED OF
ACCORDING TO LOCAL, STATE OR FEDERAL LAWS.
This projector should not be placed in a built-in installation
such as a book case unless proper ventilation is provided.
Never push objects of any kind into this projector through
cabinet slots as they may touch dangerous voltage points
or short out parts that could result in a fire or electric
shock. Never spill liquid of any kind on the projector.
Do not install the projector near the ventilation duct of air-
conditioning equipment.
5
Safety Instructions
Air Circulation
Openings in the cabinet are provided for ventilation and to
ensure reliable operation of the product and to protect it
from overheating, and these openings must not be blocked
or covered.
Do not point the projector up to project an
image.
Do not point the projector down to project
an image.
CAUTION
Hot air is exhausted from the exhaust vent. When using
or installing the projector, the following precautions
should be taken.
– Do not put any flammable object or spray can near
the projector, hot air is exhausted from the ventilation
holes.
Do not put the projector on either side to
project an image.
– Keep the exhaust vent at least 3' (1 m) away from any
objects.
– Do not touch a peripheral part of the exhaust vent,
especially screws and metallic part. This area will
become hot while the projector is being used.
– Do not put anything on the cabinet. Objects put on the
cabinet will not only get damaged but also cause fire
hazard by heat.
Moving the Projector
When moving the projector, close the slide shutter and
retract the adjustable feet to prevent damage to the
lens and cabinet. When the projector is not in use
for an extended period, put it into a suitable case to
protect the projector.
Cooling fans are provided to cool down the projector.
The fans’ running speed is changed according to the
temperature inside the projector.
When handling the projector, do not drop, bump,
subject it to strong forces, or put other things on the
cabinet.
Exhaust Vent
(Hot air exhaust)
Air flow
USE CAUTION IN CARRyING OR TRANSPORTING
THE PROjECTOR
– Do not drop or bump the projector, otherwise damages
or malfunctions may result.
– When carrying the projector, use a suitable carrying
case.
– Do not transport the projector by using a courier or
transport service in an unsuitable transport case. This
may cause damage to the projector. To transport the
projector through a courier or transport service, consult
your dealer for their information.
Air Intake Vent
– Do not put the projector in a case before the projector
is cooled enough.
Installing the Projector in Proper
Position
Install the projector properly. Improper Installation may
reduce the lamp life and cause a fire hazard.
Do not roll the projector more
than 20 degrees from side to
side.
Do not pitch the projector more
than 20 degrees above and
below.
6
Compliance
Federal Communications Commission Notice
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in
a residential installation. This equipment generates, uses, and can radiate radio frequency energy, and if not installed
and used in accordance with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help.
Use of shielded cable is required to comply with class B limits in Subpart B of Part 15 of FCC Rules.
Do not make any changes or modifications to the equipment unless otherwise specified in the instructions. If such
changes or modifications should be made, you could be required to stop operation of the equipment.
Model Number
Trade Name
: LC-XS25 / LC-XS30
: EIKI
Responsible party : EIKI International,Inc.
Address
Telephone No.
: 30251 Esperanza Rancho Santa Margarita CA 92688-2123
: 800-242-3454 (949-457-0200)
AC Power Cord Requirement
The AC Power Cord supplied with this projector meets the requirement for use in the country you purchased it.
AC Power Cord for the United States and Canada:
AC Power Cord used in the United States and Canada is listed by the Underwriters
Laboratories (UL) and certified by the Canadian Standard Association (CSA).
AC Power Cord has a grounding-type AC line plug. This is a safety feature to be sure that the
plug will fit into the power outlet. Do not try to defeat this safety feature. Should you be unable
to insert the plug into the outlet, contact your electrician.
GROUND
AC Power Cord for the United Kingdom:
This cord is already fitted with a moulded plug incorporating a fuse, the value of which is indicated on the pin face of
the plug. Should the fuse need to be replaced, an ASTA approved BS 1362 fuse must be used of the same rating,
ASA
marked thus
. If the fuse cover is detachable, never use the plug with the cover omitted. If a replacement fuse
cover is required, ensure it is of the same colour as that visible on the pin face of the plug (i.e. red or orange). Fuse
covers are available from the Parts Department indicated in your User Instructions.
If the plug supplied is not suitable for your socket outlet, it should be cut off and destroyed.
The end of the flexible cord should be suitably prepared and the correct plug fitted.
WARNING : A PLUG WITH BARED FLEXIBLE CORD IS HAZARDOUS IF ENGAGED IN A LIVE SOCKET
OUTLET
The Wires in this mains lead are coloured in accordance with the following code:
Green-and-yellow . . . . . . Earth
Blue. . . . . . . . . . . . . . . . . Neutral
Brown . . . . . . . . . . . . . . . Live
As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings
identifying the terminals in your plug proceed as follows:
The wire which is coloured green-and-yellow must be connected to the terminal in the plug which is marked by the
letter E or by the safety earth symbol
or coloured green or green-and-yellow.
The wire which is coloured blue must be connected to the terminal which is marked with the letter N or coloured
black.
The wire which is coloured brown must be connected to the terminal which is marked with the letter L or coloured red.
WARNING: THIS APPARATUS MUST BE EARTHED
THE SOCKET-OUTLET SHOULD BE INSTALLED NEAR THE EQUIPMENT AND EASILy ACCESSIBLE
7
Part Names and Functions
Front
① Air Intake Vent
② Power Cord Connector
③ Infrared Remote Receiver
④ Focus Ring (front)
⑤ Lens and Lens cover
⑥ Zoom Ring (rear)
⑦ Slide Shutter
⑧ Exhaust Vent
CAUTION
①
②
③
④ ⑤ ⑥
⑦
Hot air is exhausted from the exhaust vent. Do not
put heat-sensitive objects near this side.
Back
⑨ Lamp Cover
⑩
⑪
⑫
⑬
⑧
⑨
⑩ Speaker
⑪ Top Controls and Indicators
⑫ Terminals and Connectors
⑬ Filter Cover
⑭ Adjustable feet
Kensington Security Slot
This slot is for a Kensington lock used to deter
theft of the projector.
*Kensington is a registered trademark of ACCO Brands
Corporation.
Security Bar
A commercially available anti-theft chain or
wire can be attached to the security bar on the
projector.
Bottom
⑧
⑭
8
Part Names and Functions
Rear Terminal
⑥
④
⑤
③
②
①
⑨
⑧
⑦
① CONTROL PORT
⑦ COMPUTER1/ COMPUTER2 COMPONENT
When the projector is controlled by a computer,
connect to this jack with serial control cable.
AUDIO IN
Connect the audio output (stereo) from a
computer or video equipment connected to ② or
④ to this jack. (pp14, 16)
② COMPUTER IN 2 / COMPONENT IN
Connect output signal from a computer, RGB
scart 21-pin video output or component video
output to this terminal. (pp.14,16)
⑧ AUDIO IN
Connect the audio output from video equipment
connected to ⑤ or ⑨ to this jack. (When
the audio output is monaural, connect it to L
(MONO) jack.) (p.15)
③ MONITOR OUT
This terminal can be used to output the incoming
RGB signal from COMPUTER IN 1 / DVI-I
terminal or COMPUTER IN 2/COMPONENT IN
terminal to the other monitor (p.14).
⑨ VIDEO IN
Connect the composite video output from video
equipment to VIDEO jack. (p15)
④ COMPUTER IN 1 / DVI-I
Connect computer output (Digital/Analog DVI-I
type) to this terminal (p.14).
⑤ S-VIDEO IN
Connect the S-VIDEO output signal from video
equipment to this jack (p.15).
⑥ AUDIO OUT (VARIABLE)
Connect an external audio amplifier to this jack.
(pp.14 - 16)
This terminal outputs sound from AUDIO IN
terminal (⑦ or ⑧).
ꢀ
Part Names and Functions
Top Control
①
②
③
④
⑤
⑩
⑨
⑧
⑦
⑥
⑪
① POWER indicator
⑤ POINT (▲▼) buttons
–Light red when the projector is in stand-by
mode.
–Select an item or adjust the value in the
On-Screen Menu. (p.20)
–Light green during operations.
–Blink green in the Power management mode
(p.50).
–Pan the image in Digital zoom + mode.
(p.36)
⑥ SELECT button
–Blink red during cooling down.
–Execute the selected item. (p.20)
–Expand or compress the image in Digital
zoom mode. (p.36)
② LAMP REPLACE indicator
Turn yellow when the life of the projection lamp
draws to an end. (pp.60, 71-72)
⑦ POINT (◄►) buttons
–Select an item or adjust the value in the
On-Screen Menu. (p.20)
–Pan the image in Digital zoom + mode.
(p.36)
③ WARNING TEMP indicator
Emit a red light when the projector detects
an abnormal condition. This also blinks red
when the internal temperature of the projector
exceeds the operating range. (pp.63, 71-72)
– Adjust the volume level. (p.23)
⑧ MENU button
Open or close the On-Screen Menu. (p.20)
④ WARNING FILTER indicator
⑨ INPUT button
–Blink slow when the filter is being scrolled
(pp.57, 71).
Select an input source. (pp.25-26, 37-38)
–Blink fast when the filter cartridge is not
installed (pp.57, 72)
⑩ AUTO SETUP button
–Light orange when the clogging of the filter is
detected or the filter counter reaches a time
set in the timer setting, urging immediate filter/
filter cartridge replacement (pp.55, 57, 72).
Execute the setting of Auto setup (includes
Input search, Auto PC adj. and Auto Keystone
functions) in the setting menu.(pp.22, 24, 28, 46)
⑪ POWER ON/STAND-By button
Turn the projector on or off. (pp.18, 19)
10
Part Names and Functions
Remote Control
① POWER ON/STAND-By button
Turn the projector on or off. (pp.18, 19)
② COMPUTER 2 button
Select COMPUTER 2 input source. (pp.25, 38)
③ COMPUTER 1 button
③
②
①
Select Computer 1 (Analog) or Computer 1 (Digital)
input source. (pp.25, 26)
④ VIDEO button
2
1
Select VIDEO input source. (p.37)
⑤ S-VIDEO button
Select S-VIDEO input source. (p.37)
⑥ COMPONENT button
Select COMPONENT input source. (p. 38)
⑦ MENU button
④
⑤
⑥
Open or close the On-Screen Menu. (p.20)
⑲
⑱
⑦
⑧ Point ▲▼◄► buttons
– Select an item or adjust the value in the On-
Screen Menu. (p.20)
– Pan the image in Digital zoom + mode. (p.36)
⑧
⑨
⑨ SELECT button
– Execute the selected item. (p.20)
– Expand or compress the image in Digital zoom
mode. (p.36)
⑰
⑯
⑮
⑩
⑩ D ZOOM ▲▼ buttons
Zoom in and out the images. (pp.24, 36)
⑪
VOLUME + / – buttons
Adjust the volume level. (p.23)
+
_
⑪
⑫ FREEZE button
Freeze the picture. (p.23)
⑬ NO SHOW button
Temporarily turn off the image on the screen. (p.24)
⑭ LAMP CONTROL button
Select the lamp mode. (pp.24, 51)
⑮ MUTE button
Mute the sound. (p.23)
⑯ P-TIMER button
⑫ ⑬
⑭
Operate the P-timer function. (p.24)
⑰ IMAGE button
Select the image level. (pp.24, 31, 40)
⑱ AUTO SET button
To ensure safe operation, please observe
the following precautions:
Execute the setting of Auto setup (includes Input
search function, Auto PC adj. function and Auto
Keystone function). (pp.22,24,28,46)
– Do not bend, drop or expose the remote
control to moisture or heat.
– For cleaning, use soft dry cloth. Do not
apply benzene, thinner, spray or any
chemical material.
⑲ KEySTONE button
Correct the keystone distortion. (pp.22, 47)
11
Part Names and Functions
Remote Control Battery Installation
Open the battery
compartment lid.
Install new batteries
into the compartment.
Replace the
compartment lid.
1
2
3
Two AA size batteries
For correct polarity
(+ and –), be sure
battery terminals are in
contact with pins in the
compartment.
To ensure safe operation, please observe the following precautions:
● Use two (2) AA or LR6 type alkaline batteries.
● Always replace batteries in sets.
● Do not use a new battery with a used battery.
● Avoid contact with water or liquid.
● Do not expose the remote control to moisture or heat.
● Do not drop the remote control.
● If the battery has leaked on the remote control, carefully wipe the case clean and install new
batteries.
● Risk of explosion if a battery is replaced by an incorrect type.
● Dispose of used batteries according to the instructions.
Operating Range
16.4'
(5 m)
Point the remote control toward the
projector (Infrared Remote Receiver)
when pressing any button. Maximum
operating range for the remote control is
about 16.4' (5 m) and 60° in front of the
projector.
12
Installation
Positioning the Projector
For projector positioning, see the figures below. The projector should be set horizontally to the flat screen.
Notes:
• The brightness in the room has a great influence on picture quality. It is recommended to limit ambient
lighting in order to obtain the best image.
• The values shown below are approximate and may vary from the actual sizes.
41.8' (12.7 m)
34.8' (10.6 m)
23.2' (7.1 m)
17.4' (5.3 m)
11.6' (3.5 m)
4.6' (1.4 m)
Screen Size
(W x H) mm
40"
100"
150"
200"
300"
4 : 3 aspect ratio
813 x 610
4.6' (1.4 m)
5.5' (1.7 m)
2032 x 1524
11.6' (3.5 m)
13.9' (4.2 m)
3048 x 2286
17.4' (5.3 m)
20.9' (6.4 m)
4064 x 3048
23.2' (7.1 m)
27.8' (8.5 m)
6096 x 4572
34.8' (10.6 m)
41.8' (12.7 m)
Zoom (max)
Zoom (min)
Adjustable Feet
Projection angle can be adjusted up to 10.0 degrees with the adjustable feet.
Lift the front of the projector and push the feet lock
latches on the projector.
1
Release the feet lock latches to lock the adjustable
feet and rotate the adjustable feet to adjust the
position and tilt.
2
To retract the adjustable feet, lift the front of the
3
projector and push and undo the feet lock latches.
Keystone distortion of the projected image can be
corrected with the remote control or menu operation.
(pp.22, 46)
Adjustable Feet
Feet Lock Latches
13
Installation
Connecting to a Computer
Cables used for connection
• DVI Cable or DVI-VGA Cable
• VGA Cables (Mini D-sub 15 pin) (Only one cable is supplied.)
• Audio Cables (Mini Plug: stereo)
( Not all the cables are supplied with this projector.)
Audio Output
Monitor Output Monitor Input Monitor Output
External Audio Equipment
Audio Input
V G A
cable
VGA
cable
DVI
cable
DVI-VGA
cable
Audio cable
(stereo)
COMPUTER IN 2 MONITOR OUT COMPUTER IN
/COMPONENT IN 1/ DVI-I
Audio cable
(stereo)
AUDIO OUT
(stereo)
COMPUTER 2
/ COMPONENT
/COMPUTER 1
AUDIO IN
Notes:
• Input sound to the COMPUTER 2 / COMPONENT AUDIO IN terminal when using the COMPUTER IN 2
/COMPONENT IN as input.
• Input sound to the COMPUTER 1 AUDIO IN terminal when using the COMPUTER IN 1 / DVI-I terminal
as input.
• When the AUDIO OUT is plugged-in, the projector's built-in speaker is not available.
Unplug the power cords of both the projector and external equipment from the AC outlet before
connecting cables.
14
Installation
Connecting to Video Equipment
Cables used for connection
• Video and Audio Cable (RCA x 3)
• S-video Cable
• Audio Cables (RCA x 2, Mini Plug: stereo)
(Cables are not supplied with the projector.)
S-video Output
(R) (L)
Composite Video and Audio Output
(R) (L) (Video)
External Audio Equipment
S-video
cable
Audio cable
(stereo)
Video and
Audio cable
Audio Input
(R) (L) (Video)
S-VIDEO IN (R) (L)
Audio cable
(stereo)
AUDIO OUT
(stereo)
Note:
When the AUDIO OUT is plugged-in, the projector's built-in speaker is not available.
Unplug the power cords of both the projector and external equipment from the AC outlet before
connecting cables.
15
Installation
Connecting to Component Video and RGB (Scart) Equipment
Cables used for connection
• Audio Cables (Mini Plug :stereo)
• Scart-VGA Cable
• Component Cable
• Component-VGA Cable
(Cables are not supplied with the projector.)
RGB Scart
21-pin Output
Component Video Output
(Y, Pb/Cb, Pr/Cr)
Audio Output
External Audio Equipment
Component cable
Scart-VGA
cable
Audio Input
Component-VGA cable
Audio cable
(stereo)
Audio cable (stereo)
COMPUTER IN 1/COMPONENT IN
AUDIO OUT
(stereo)
COMPUTER2/
COMPONENT
AUDIO IN
Notes:
• When the AUDIO OUT is plugged-in, the projector's built-in speaker is not available.
• See page 76 for ordering optional parts.
Unplug the power cords of both the projector and external equipment from the AC outlet before
connecting cables.
16
Installation
Connecting the AC Power Cord
This projector uses nominal input voltages of 100-120 V
or 200-240 V AC. This projector automatically selects
the correct input voltage. It is designed to work with
single-phase power systems having a grounded neutral
conductor. To reduce the risk of electrical shock, do not
plug into any other type of power system.
Consult your authorized dealer or service station if you are
not sure of the type of power being supplied.
Connect the projector with all peripheral equipment before
turning the projector on. (See pages 14-16 for connection.)
CAUTION
The AC outlet must be near this equipment and must be easily
accessible.
Note:
Unplug the AC power cord when the projector is not in use.
When this projector is connected to an outlet with the AC
power cord, it is in Stand-by mode and consumes a little
electric power.
Connect the AC power cord
(supplied) to the projector.
NOTE ON THE POWER CORD
AC power cord must meet requirement of the country where you use the projector.
Confirm the AC plug type with the chart below and proper AC power cord must be used.
If supplied AC power cord does not match your AC outlet, contact your sales dealer.
Projector side
AC outlet side
For the U S A and Canada
For Continental Europe
For the U K
Ground
To power cord
connector on your
projector.
To the AC outlet.
(120 V AC)
To the AC outlet.
(200 - 240 V AC)
To the AC outlet.
(200 - 240 V AC)
17
Basic Operation
Turning On the Projector
Complete peripheral connections (with a computer,
VCR, etc.) before turning on the projector.
1
16
Connect the projector’s AC power cord into an AC
2
outlet. The POWER indicator becomes red.
Press the POWER ON/STAND-BY button on the
3
top control or on the remote control. The POWER
indicator becomes green and the cooling fans start
to operate. The preparation display appears on the
screen and the count down starts.
The preparation display disappears after 30
seconds.
Selected Input Source and Lamp Mode
After the countdown, the input source that was
selected the last time and the Lamp mode status icon
(see page 51) appears on the screen.
4
Lamp mode
If the projector is locked with a PIN code, PIN code
Input Dialog Box appears. Enter the PIN code as
instructed below.
(See page 51 for Lamp mode.)
Note:
The Filter warning and Lamp replacement icons
may appear on the screen depending on the
usage state of the projector.
To Enter a PIN code
Select a number by pressing the Point ▲▼ buttons,
and then press the Point ►button to fix the number
and move the pointer. The number changes to "". If
you fixed an incorrect number, move the pointer to the
number you want to correct by pressing the Point ◄
button, and then select the correct number by pressing
the Point ▲▼ buttons.
PIN Code Input Dialog Box
Repeat this step to complete entering a four-digit
number.
"1234" is set as the initial PIN code at the factory.
After entering the four-digit number, move the pointer
to "Set" by pressing the Point ►button. Press the
SELECT button so that you can start to operate the
projector.
After the OK icon
disappears, you can
operate the projector.
If you entered an incorrect PIN code, "PIN code" and
the number () turns red. Enter the correct PIN
code all over again.
Notes:
• When the Input Search function is set
On1 or On2, the input signal will be
searched automatically (p.46)
What is PIN code?
PIN (Personal Identification Number) code that allows
the person who knows it to operate the projector.
Setting a PIN code prevents unauthorized use of the
projector.
• When the Logo select function is off,
the logo is not shown on the screen.
(p.48)
A PIN code consists of a four-digit number. Refer to the
PIN code lock function in the Setting on pages 53 and
54 for locking operation of the projector with your PIN
code.
• When the "Countdown off" or "Off" is
selected in the Display function, the
countdown is not shown on the screen.
(p.47)
CAUTION ON HANDLING PIN CODE
• During the countdown period, all
operations are invalid.
If you forget your PIN code, the projector can no longer
be started. Set a new PIN code with special care,
write it down in column on page 79 of this manual, and
keep it on hand. Should the PIN code be missing or
forgotten, consult your dealer or service center.
• If the PIN code number is not input for
three minutes after the PIN code dialog
box appeared, the projector is turned off
automatically.
18
Basic Operation
Turning Off the Projector
Press the POWER ON/STAND-BY button on the
top control or on the remote control, and a message
"Power off?" appears on the screen.
1
Press the POWER ON/STAND-BY button again to
2
turn off the projector.The POWER indicator starts to
blink red, and the cooling fans keep running. (You can
select the level of fan quietness and rotation speed.
See page 55.)
The message disappears after 4 seconds.
At this time you can disconnect the AC power cord
even if the fans are still running.
When the projector has cooled down enough, the
POWER indicator stops blinking and you can turn on
the projector.
3
TO MAINTAIN THE LIFE OF THE LAMP, ONCE
YOU TURN THE PROJECTOR ON, WAIT AT
LEAST FIVE MINUTES BEFORE TURNING IT OFF.
D O N O T O P E R AT E T H E P R O J E C T O R
CONTINUOUSLY WITHOUT REST.CONTINUOUS
USE MAY RESULT IN SHORTENTING THE LAMP
LIFE.TURN OFF THE PROJECTOR AND GIVE IT A
REST ABOUT AN HOUR IN EVERY 24 HOURS.
Notes:
• When the On start function is on, this projector is turned on automatically by connecting the AC power
cord to an AC outlet. (p.51)
• The running speed of cooling fans is changed according to the temperature inside the projector.
• Do not put the projector in a case before the projector is cooled enough.
• If the WARNING TEMP. indicator blinks or emits a red light, see "Indicators and Projector Condition" on
pages 71-72.
• While the POWER indicator is blinking, lamp is being cooled down and the projector cannot be turned
on. Wait until the POWER indicator stops blinking to be turned on again.
• The fan rotation will terminate directly if the AC power cord is unplugged immediately after the projector
is turned off.
• The projector can be turned on after the POWER indicator turns red. The waiting time to restart will be
shortened when the normal power-off processing for fan cooling is completed, compared with the time
the AC power cord is immediately unplugged after the power-off.
1ꢀ
Basic Operation
How to Operate the On-Screen Menu
The projector can be adjusted or set via the On-Screen
Menu. Refer to the following pages regarding each
adjustment and setting procedures.
Top Control
Press the MENU button to display the On-Screen
Menu.
1
POINT buttons
(outer ring)
Press the Point ◄► buttons to select a Menu icon to
adjust and press the Point ▲▼ buttons to select an
2
MENU button SELECT button
item to adjust.
Press the SELECT button to show the item data. To
adjust the data, press the Point ◄► buttons. Refer to
3
Remote Control
the following pages for each adjustment.
MENU button
POINT buttons
To close the On-Screen Menu, press the MENU button
again.
Note:
The selected item is not active until the SELECT
button is pressed.
SELECT button
Menu icon
On-Screen Menu
Pointer
(red frame )
Menu bar
Pointer (red frame )
Press the Point ▲▼ buttons to
move the pointer.
Item
SELECT
button
Press the SELECT button here
to display previous items.
Item data
Press the Point ◄►
buttons to adjust the
value.
Press the SELECT button here to
display next items.
Quit
Exit this menu.
20
Basic Operation
Menu Bar
For detailed functions, see Menu Tree on pages 68-70.
For computer source
Guide Window
PC System Menu Image Select Menu
Screen Menu
Setting Menu
Show the selected Used to select
M e n u o f t h e computer system.
U s e d t o s e l e c t a n
image level among
Dynamic, Standard,
R e a l , B l a c k b o a r d
(Green), Colorboard
Used to adjust size of U s e d t o s e t t h e
image. [Normal / True projector's operating
/ Wide / Full / Custom configurations.
/ Digital zoom +/–] (pp.45-56)
(pp34-36)
On-Screen Menu.
(p.27)
a n d I m a g e
(pp.31-32)
1
~
4 .
Input Menu
PC Adjust Menu
Image Adjust Menu
Sound Menu
U s e d t o s e l e c t
input source either parameters to match
Computer or Video.
(pp.25,26)
U s e d t o a d j u s t
Used to adjust computer
Used to adjust the
volume or mute the
sound. (p.23)
i m a g e . [ C o n t r a s t
/
with input signal
format. (pp.28-30)
Brightness / Color temp.
/ White balance (R/G/B)
/ Sharpness / Gamma]
(pp.33-34)
Note:
Items will be same as the items in video source
when 480i, 575i, 480p, 575p, 720p, 1035i or 1080i is
selected.
For video source
Input Menu
Image Select Menu
Screen Menu
Used to select an image level among
Dynamic, Standard, Cinema, Blackboard
(Green), Colorboard and Image 1 ~ 4.
(pp.40-41)
Used to select input
source either Video or
Computer. (pp.37, 38)
Used to set size of
image to Normal, Wide
or Custom. (p.44)
Same function as
menu for computer
source.
Same function
a s c o m p u t e r
menu.
AV System Menu
Image Adjust Menu
Used to select system
o f s e l e c t e d v i d e o
source. (p.39)
Used to adjust picture image.
[Contrast / Brightness / Color / Tint
/ Color temp. / White balance (R/
G/B) / Sharpness / Gamma / Noise
reduction / Progressive ] (pp.42-43)
21
Basic Operation
Zoom and Focus Adjustment
Open the slide shutter.
Focus Ring
(Front)
Zoom Ring
(Rear)
Slide Shutter
Rotate the Zoom Ring to zoom in and out.
Rotate the Focus Ring to adjust the projected picture
focus.
Close the slide shutter.
Note:
Close the slide shutter of lens operation part to keep
out dust just after zoom and focus adjustments.
Auto setup function
Top Control
Auto setup function is provided to automatically execute
the setting of Auto setup (includes Input search, Auto PC
adj. and Auto Keystone functions) in the setting menu by
just pressing the AUTO SETUP button on the top control or
the AUTO SET button on the remote control. Refer to page
46 for the setting of the Auto setup function.
AUTO SETUP button
AUTO SET button
Remote Control
Keystone Correction
If a projected picture still has keystone distortion after
pressing the AUTO SETUP button on the top control,
correct the image manually as follows:
• The arrows are white when there is no
correction.
• The direction of the arrow being corrected turns
red.
• The arrows disappear at the maximum
correction.
• If you press the KEYSTONE button on the
remote control once more while the keystone
dialog box is being displayed, the keystone
adjustment is canceled.
Press the KEYSTONE button on the remote control. The
keystone dialog box appears.
Correct keystone distortion by pressing the Point ▲▼
buttons. Keystone adjustment can be memorized. (p.47)
• The adjustable range is limited depending on the
input signal.
Reduce the upper width
Reduce the lower width
with Point ▲ button.
with Point ▼ button.
Top Control
POINT ▲▼ buttons
Remote Control
KEySTONE button
POINT ▲▼ buttons
22
Basic Operation
Sound Adjustment
Direct Operation
Top Control
VOLUME+/– buttons
Volume
Press the VOLUME+/– buttons on the top control or on
the remote control to adjust the volume. The volume
dialog box appears on the screen for a few seconds.
Mute
Remote Control
Press the MUTE button on the remote control to cut off the
sound. To restore the sound to its previous level, press
the MUTE button again or press the VOLUME +/– buttons.
Mute function is also effective for AUDIO OUT jack.
VOLUME+ button
+
_
MUTE button
Menu Operation
VOLUME- button
Press the MENU button to display the On-Screen
Menu. Press the Point ◄► buttons to move the red
1
frame pointer to the Sound Menu icon.
Press the Point ▲▼ buttons to move the red frame
pointer to the item that you want to select, and then
press the SELECT button.
Approximate level
of the volume.
2
Volume
Press the Point ► button to turn up the volume, and press
the Point ◄ button to turn down the volume.
Press the MUTE button to set the Mute function
On/Off. The display disappears after 4 seconds.
Mute
Press the Point ◄► buttons to cut off the sound. Dialog
box display changes to "On" and the sound is cut off. To
restore the sound to its previous level, press the Point ◄►
buttons again.
Sound Menu
Sound Menu icon
Approximate level of
the volume.
Remote Control Operation
For some frequently used operations, using the remote
control is advisable.
Exit the Sound Menu.
Just pressing one of the buttons enables you to make the
operation, and no need for calling up the On-Screen Menu.
Remote Control
COMPUTER1/
COMPUTER2/
VIDEO / S-VIDEO/
COMPONENT
buttons
COMPUTER/ VIDEO / S-VIDEO /COMPONENT buttons
Press the COMPUTER or VIDEO or S-VIDEO or
COMPONENT button on the remote control to select the
input source. For more detail, see pages 25,26,37 and 38.
2
1
FREEZE button
FREEZE button
Press the FREEZE button on the remote control to freeze
the picture on the screen. To cancel the Freeze function,
press the FREEZE button again or press any other button.
Note:
See the next page for the other buttons.
23
Basic Operation
Remote Control
AUTO SET button
Press the AUTO SET button on the remote control to
operate the Auto setup function. For more detail, see
pages 22, 28,46.
D ZOOM buttons
KEySTONE button
(See p.22)
D ZOOM buttons
Press the D.ZOOM buttons on the remote control to zoom
POINT ▲▼ buttons
in and zoom out the images. For more detail, see page
36.
AUTO SET button
NO SHOW button
IMAGE button
Press the NO SHOW button on the remote control to black
out the image. To restore to normal, press the NO SHOW
button again or press any other button. When a projected
image is captured and set as "User" in the Logo selection
(p.48), the screen changes each time you press the NO
SHOW button as follows.
P-TIMER button
+
_
NO SHOW button
LAMP CONTROL button
Note:
• • • • •
black out → the captured image → normal →
See the previous page for the other
buttons.
KEySTONE button
For detail, see page 22.
IMAGE button
Press the IMAGE button on the remote control to select
a desired image level of the screen. For more detail, see
pages 31 and 40.
P-TIMER button
The message disappears after 4 seconds.
Press the P-TIMER button on the remote control. The
timer display "00 : 00" appears on the screen and the
timer starts to count time (00 : 00 ~ 59 : 59).
To stop the P-Timer, press the P-TIMER button. Press
the P-TIMER button again, then the P-timer display
disappears.
LAMP CONTROL button
P-Timer display
Press the LAMP CONTROL button on the remote control
to select the lamp mode for changing the brightness of the
screen.
Normal. . . normal brightness
Auto . . . . . brightness according with the input signal
Eco........... lower brightness reduces the lamp
power consumption and extends the
lamp life.
Note:
Lamp mode cannot be changed for a while after
turning on the projector. Lamp needs some time to
stabilize after the power is turned on. Stored lamp
mode will be active after the lamp is stabilized.
24
Computer Input
Input Source Selection (RGB: Computer 1 (Analog)/Computer 2 )
Top Control
Direct Operation
Choose Computer 1 (Analog) or Computer 2 by pressing
the INPUT button on the top control or choose Computer
1(Analog) by pressing the COMPUTER 1 button on
the remote control or choose computer 2 by pressing
COMPUTER 2 button on the remote control.
INPUT button
Before using these buttons, correct input source should be
selected through Menu operation as described below.
Computer 1 (Analog)
Computer 1 (Digital)
Computer 2
Video
Remote Control
COMPUTER 1 button
COMPUTER 2 button
2
1
Menu Operation
COMPUTER 1 button
Press the MENU button to display the On-Screen
Menu. Press the Point ◄► buttons to move the red
Computer 1 (Analog)
1
frame pointer to the Input Menu icon.
Computer 1 (Digital)
Press the Point ▲▼ buttons to move the red arrow
pointer to either Computer 1 (Analog) or Computer 2,
and then press the SELECT button.
2
Input Menu icon
Input Menu
Input Menu
When selecting Computer 1 (Analog), RGB input
source will be selected directly.
3
Move the pointer (red
When selecting Computer 2, the Source Select Menu
appears. Move the pointer to RGB and then press the
SELECT button.
a r r o w ) t o C o m p u t e r
1(Analog) and press the
SELECT button.
Move the pointer (red
arrow) to Computer 2 and
press the SELECT button.
Computer
2
Move the pointer (red
arrow) to RGB.
Notes:
When the Input Search function is set On1 or On2, the
input signal will be searched automatically. (p.46)
25
Computer Input
Input Source Selection (RGB(PC digital), RGB(AV HDCP))
Top Control
Direct Operation
Choose Computer 1 (Digital) by pressing the INPUT button
on the top control or press the COMPUTER 1 button on
the remote control.
INPUT button
Before using these buttons, correct input source should be
selected through Menu operation as described below.
Computer 1 (Analog)
Computer 1 (Digital)
Computer 2
Video
Remote Control
COMPUTER 1 button
2
1
Computer 1 (Analog)
Computer 1 (Digital)
Menu Operation
Input Menu icon
Input Menu
Press the MENU button to display the On-Screen
1
Menu. Press the Point ◄► buttons to move the red
frame pointer to the Input Menu icon.
Move the pointer (red
arrow) to Computer 1
(Digital) and press the
SELECT button.
Press the Point ▲▼ buttons to move the red arrow
pointer to Computer 1 (Digital) , and then press the
SELECT button.
2
Computer
1
After the Source Select Menu appeared for Computer
3
1 (Digital), move the pointer to RGB (PC digital) or
RGB (AV HDCP), and then press the SELECT button.
Move the pointer to the
source that you want
to select and press the
SELECT button.
Notes:
•
HDCP (High-bandwidth Digital Content Protection) is
a system for protecting digital entertainment content
delivered by DVI (Digital Visual Interface) from being
copied. The specification of HDCP is decided and
controlled by Digital Content Protection, LLC. Should
the specification be changed, this projector may not
display the digital content protected by HDCP.
•
When the Input Search function is set On1 or On2, the
input signal will be searched automatically. (p.46)
26
Computer Input
Computer System Selection
This projector automatically tunes to various types of computers based on VGA, SVGA, XGA, SXGA,
WXGA, or UXGA with its Multi-scan system and Auto PC Adjustment. If Computer is selected as a signal
source, this projector automatically detects the signal format and tunes to project a proper image without
any additional setting. (Signal formats provided in this projector is shown on pages 73-74)
One of the following messages may appear when:
PC System Menu
The projector cannot recognize the connected
signal conforming to the provided PC Systems.
The message "Auto" is displayed on the PC
System Menu icon and the Auto PC Adjustment
function works to display proper images. If
the image is not projected properly, a manual
adjustment is required. (pp.29-30)
Auto
The Auto PC Adjustment
function operates to adjust
the projector.
There is no signal input from computer. Check
the connection between your computer and
the projector. (See "Troubleshooting" on pages
65-67.)
-----
The preset system is manually adjusted in the
PC Adjust Menu. The adjusted data can be
stored in Mode 1 ~ 5. (pp.29-30)
Mode 1
SVGA 1
PC Systems provided in this projector is
chosen. The projector chooses a proper
system provided in the projector and displays
it.
*Mode 1 and SVGA 1 are examples.
PC System Menu
Selecting Computer System Manually
PC system can also be selected manually.
Press the MENU button to display the On-Screen
Menu. Press the Point ◄► buttons to move the red
1
The PC System Menu icon
Selected system is displayed.
frame pointer to the PC System Menu icon.
Systems on this dialog
box can be selected.
Press the Point ▲▼ buttons to move the red arrow
pointer to the system that you want to set, and then
press the SELECT button.
2
Custom Mode (1 ~ 5) set in the
PC Adjust Menu. (p.30)
27
Computer Input
Auto PC Adjustment
Auto PC Adjustment function is provided to automatically adjust Fine sync, Total dots, Horizontal, and
Vertical to conform to your computer. Auto PC Adjustment function can be operated as follows.
Direct Operation
Remote Control
The Auto PC adjustment function can be operated directly
by pressing the AUTO SETUP button on the top control or
the AUTO SET button on the remote control.(p.46)
AUTO SET button
+
Top Control
AUTO SETUP
button
Menu Operation
Auto PC Adj
Press the MENU button to display the On-Screen
Menu. Press the Point ◄► buttons to move the red
1
frame pointer to PC Adjust Menu icon.
PC Adjust Menu
Press the Point ▲▼ buttons to move the red frame
pointer to Auto PC Adj. item and then press the
SELECT button twice.
2
PC Adjust Menu icon
To store adjustment parameters
Move the red frame pointer to the
Auto PC Adj. item and press the
SELECT button.
Adjustment parameters from Auto PC Adjustment can
be memorized in this projector. Once parameters are
memorized, the setting can be done just by selecting Mode
in the PC System Menu (p.27). See "Store" on page 30.
"Please wait..." message appears
while Auto PC adjustment is in
process.
Notes:
• Fine sync, Total dots, Horizontal, and Vertical of some
computers cannot be fully adjusted with this Auto PC
Adjustment function. When the image is not provided
properly with this operation, manual adjustments are
required. (pp.29-30)
• The Auto PC Adjustment cannot be operated when
480i, 575i, 480p, 575p, 720p,1035i, or 1080i is
selected in the PC System Menu, or when the digital
signal is input into DVI terminal. (p.27)
28
Computer Input
Manual PC Adjustment
Some computers employ special signal formats which may not be tuned by Multi-scan system of this
projector. Manual PC Adjustment enables you to precisely adjust several parameters to match those signal
formats. The projector has 5 independent memory areas to memorize those parameters manually adjusted.
It allows you to recall the setting for a specific computer.
PC Adjust Menu icon
Press the MENU button to display the On-Screen
Menu. Press the Point ◄► buttons to move the red
frame pointer to the PC Adjust Menu icon.
PC Adjust Menu
1
2
Press the Point ▲▼ buttons to move the red frame
pointer to the item that you want to adjust and then
press the SELECT button to display the adjustment
dialog box. Press the Point ◄► buttons to adjust the
value.
Move the red frame pointer
to an item and press the
SELECT button.
Fine sync
Eliminate flicker from the image displayed. Press the
Point ◄► buttons to adjust the value. (From 0 to 31.)
Status (Stored/Free)
of the selected Mode.
Selected Mode
Total dots
Adjust the number of total dots in one horizontal period.
Press the Point ◄► buttons to adjust number to match
your PC image.
Press the Point ◄►
buttons to adjust the
value.
Horizontal
Press the Point ◄► buttons to adjust the horizontal picture
position.
Vertical
Press the Point ◄► buttons to adjust the vertical picture
position.
Current mode
Press the SELECT button to show H-sync freq. and
V-sync freq. of the connected computer.
Clamp
Adjust clamp level. When the image has dark bars, try
this adjustment.
Press the SELECT button
at the Current mode item to
show the information of the
connected computer.
2ꢀ
Computer Input
Display area H
Adjust the horizontal area displayed by this projector.
Press the Point ◄► buttons to decrease/increase the
value.
Display area V
Adjust the vertical area displayed by this projector. Press
the Point ◄► buttons to decrease/increase the value.
M o v e t h e r e d f r a m e
pointer to an item and
press the SELECT button.
Reset
To reset the adjusted data, select Reset and press the
SELECT button. The confirmation box appears and
then select [Yes]. All adjustments return to their previous
figures.
This Mode has stored parameters.
Mode free
To clear adjusted data
To clear the stored data, move the red frame pointer to the
Mode free item and then press the SELECT button. Move
the red arrow pointer to the Mode that you want to clear
and then press the SELECT button.
Store
To store adjusted data, move the red frame pointer to the
Store item and then press the SELECT button. Move the
red arrow pointer to any of Mode 1 to 5 in which you want
to store and then press the SELECT button.
Vacant Mode
Values of "Total dots",
"Horizontal", "Vertical",
"Display area H" and
"Display area V".
Quit
To store adjusted data
Exit the PC Adjust Menu.
Close this dialog box.
Note:
• Display area (H/V) cannot be selected when 480i,
575i, 480p, 575p, 720p, 1035i, or 1080i is selected in
the PC System Menu (p.27).
• PC Adjust Menu cannot be selected when Computer
1(Digital) is selected in the Input Menu. (p.26)
30
Computer Input
Image Level Selection
Remote Control
Direct Operation
Select an image level among Dynamic, Standard, Real,
Blackboard (Green), Colorboard, Image 1, Image 2, Image
3, and Image 4 by pressing the IMAGE button on the
remote control.
IMAGE button
Dynamic
IMAGE button
Dynamic
Picture level suitable for viewing picture in a bright room.
Standard
Standard
Real
Normal picture level preset on this projector.
Real
Picture level with improved halftone for graphics.
Blackboard (Green)
Blackboard (Green)
Colorboard
Picture level suitable for the image projected on a
blackboard. This mode assists to enhance the image
projected on a blackboard. This is mainly effective on a
green colored board, not truly effective on a black colored
board.
Image 1
Colorboard
Image 2
Image 3
Image 4
At the time of simple projection on the colored wall, you
can get the close color image to the color image projected
on a white screen by selecting the similar color to the wall
color from the preset four colors.
Image 1 ~ 4
User preset image in the Image Adjust Menu. (pp.33-34)
31
Computer Input
Image Select Menu icon
Menu Operation
Press the MENU button to display the On-Screen
Menu. Press the Point ◄► buttons to move the red
Image Select Menu
1
frame pointer to the Image Select Menu icon.
Press the Point ▲▼ buttons to move the red frame
pointer to the level that you want to set and then press
the SELECT button.
2
M o v e t h e r e d f r a m e
pointer to the level and
press the SELECT button.
Dynamic
Picture level suitable for viewing picture in a bright room.
Standard
Normal picture level preset on this projector.
Real
The level being selected.
Picture level with improved halftone for graphics.
Blackboard (Green)
Picture level suitable for the image projected on a
blackboard. See above for further description.
Colorboard
At the time of simple projection on the colored wall, you
can get the close color image to the color image projected
on a white screen by selecting the similar color to the
wall color from the preset four colors. Press the SELECT
button to choose the color.
Image 1 ~ 4
User preset image in the Image Adjust Menu. (pp.33-34)
32
Computer Input
Image Level Adjustment
Press the MENU button to display the On-Screen
Menu. Press the Point ◄► buttons to move the red
Image Adjust Menu
1
frame pointer to the Image Adjust Menu icon.
Press the Point ▲▼ buttons to move the red frame
Image Adjust Menu icon
Move the red frame
pointer to the item to be
selected and then press
the SELECT button.
2
pointer to the item that you want to adjust, and then
press the SELECT button. The level of each item is
displayed. Adjust each level by pressing the Point ◄►
buttons.
Contrast
Press the Point ◄ button to decrease the contrast and the
Point ► button to increase contrast. (From 0 to 63.)
Brightness
Press the Point ◄ button to adjust the image darker and
the Point ► button to adjust the image brighter. (From 0 to
63.)
Selected Image level
Color temp
Press the Point ◄ button or the Point ► button for Color
temp. level that you want to select. (XLow, Low, Mid, or
High)
Press the Point ◄►
buttons to adjust the
value.
White balance (Red)
Press the Point ◄ button to lighten the red tone and the
Point ► button to deepen the red tone. (From 0 to 63.)
White balance (Green)
Press the Point ◄ button to lighten the green tone and the
Point ► button to deepen the green tone. (From 0 to 63.)
White balance (Blue)
Press the Point ◄ button to lighten the blue tone and the
Point ► button to deepen the blue tone. (From 0 to 63.)
Sharpness
Press the Point ◄ button to soften the image and the Point
► button to sharpen the image. (From 0 to 15.)
Gamma
Press the Point ◄► buttons to obtain better balance of
contrast. (From 0 to 15.)
Reset
Note:
To reset the adjusted data, select Reset and press the
SELECT button. The confirmation box appears and then
select [Yes]. All adjustments returns to their previous
figures.
After adjusting any of the White balance
Red, Green, or Blue, the Color temp
changes to "Adj.".
33
Computer Input
Store
To store the adjusted data, select Store and press the
SELECT button. Select a level from Image 1 to 4 with the
Point ▲▼ buttons and press the SELECT button.
A confirmation box appears and then select [Yes].
Stored data can be called up by selecting "Image" in the
Image Level Selection on page 31.
Move the red frame
pointer to any of
Image 1 to 4 where
y o u w a n t t o s e t
and then press the
SELECT button.
Quit
The confirmation
b o x a p p e a r s ,
then select [Yes].
Store item
Exit the Image Adjust Menu.
Press the SELECT
b u t t o n a t t h i s
item to store the
adjusted data.
Screen Size Adjustment
This projector has the picture screen resize function, which
enables you to customize the image size.
Press the MENU button to display the On-Screen
Menu. Press the Point ◄► buttons to move the red
1
frame pointer to the Screen Menu icon.
Screen Menu icon
Press the Point ▲▼ buttons and move the red frame
pointer to the function that you want to select and then
press the SELECT button.
2
Screen Menu
Normal
Provide the image to fit the screen size.
Move the red frame pointer
to the function and press the
SELECT button.
True
Provide the image in its original size. When the original
image size is larger than the screen size (1024 x 768 ),
this projector enters panning mode automatically. Pan the
image with Point ▲▼◄► buttons. When adjusted, the
arrows turn red. When reached to the correction limit, the
arrows disappear.
Notes:
• This Screen Menu, except for "Normal" and "Custom",
cannot be operated when 720p(HDTV), 1035i (HDTV),
or 1080i (HDTV) is selected in the PC System Menu
(p.27).
• The projector cannot display any resolution higher
than 1600x1200. If your computer’s screen resolution
is higher than it, reset the resolution to the lower
before connecting to the projector.
• The image data in other than XGA (1024x768) is
modified to fit the screen size in initial mode.
• True, Full, and Digital zoom +/– cannot be selected
when 480i, 575i, 480p, or 575p is selected in the PC
System Menu (p.27).
34
Computer Input
Wide
Provide the image to fit wide video aspect ratio (16:9) by
expanding the image width uniformly. This function can be
used for providing a squeezed video signal at 16:9.
Full
Provide the full screen image.
Custom
Adjust the screen scale and position manually with this
function.
Press the SELECT button at Custom and the "Custom" is
displayed on the screen for a few seconds and then the
Aspect dialog box appears.
Scale H/V.................. Adjust the Horizontal/Vertical screen
scale.
H&V........................... When set to "On", the aspect ratio
is fixed. The "Scale V" appears
dimmed and becomes unavailable.
Adjust the "Scale H", then the
screen scale is automatically
modified based on the aspect ratio.
Position H/V............. Adjust the Horizontal/Vertical screen
position.
Common ................... Save the adjusted scale to all the
inputs. Press the SELECT button at
Common to display a confirmation
box. To save the scale, press the
SELECT button at "Yes", When
Custom is selected, the saved scale
is used.
Press the SELECT button at
Common or Reset, to display
a confirmation box.
Reset......................... Reset the all adjusted values. Press
the SELECT button at Reset to
display a confirmation box. To reset,
press the SELECT button at "Yes".
Notes:
• When no signal is detected, "Normal" is set
automatically and the Aspect dialog box disappears.
• The adjustable range for Scale H/V and Position H/V
is limited depending on the input signal.
35
Computer Input
For zooming in and out the images
Digital zoom +
Remote Control
POINT buttons
When the Digital zoom + is selected, the On-Screen Menu
disappears and the message "D. zoom +" is displayed.
Press the SELECT button to expand the image size. And
press the Point ▲▼◄► buttons to pan the image. The
Panning function can work only when the image is larger
than the screen size.
SELECT button
D ZOOM ▲ button
D ZOOM ▼ button
A projected image can be also expanded by pressing the
D.ZOOM ▲ button on the remote control.
Digital zoom –
When Digital zoom – is selected, the On-Screen Menu
disappears and the message "D. zoom –" is displayed.
Press the SELECT button to compress image size.
A projected image can be also compressed by pressing
the D.ZOOM ▼ button on the remote control.
To exit the Digital zoom +/– mode, press any button except
the D.ZOOM ▲▼ buttons, SELECT, and Point buttons.
To return to the previous screen size, select a screen size
from the Screen Size Adjustment or select an input source
from the Input Source Selection (p.26) again, or adjust the
screen size with the D.ZOOM ▲▼buttons.
Notes:
• The panning function may not operate properly if the
stored Mode in the PC Adjust Menu is used. (p.30)
• The minimum compression ratio can be limited
depending on the input signal or when the Keystone
function is working or when the Custom is selected for
the screen size.
• True, Full, and Digital zoom +/– cannot be selected
when 480i, 575i, 480p, or 575p is selected in the PC
System Menu (p.27).
• Digital zoom +/- cannot be selected when Full or True
is selected.
36
Video Input
Input Source Selection (Video, S-video)
Direct Operation
Top Control
Choose Video by pressing the INPUT button on the top
control or choose Video by pressing the VIDEO button
or choose S-video by pressing the S-video button on the
remote control.
INPUT button
Before using these buttons, correct input source should be
selected through menu operation as described below.
Computer 1 (Analog)
Computer 1 (Digital)
Computer 2
Video
Remote Control
VIDEO button
2
1
S-VIDEO button
Menu Operation
Input Menu icon
Press the MENU button to display the On-Screen
Input Menu
1
Menu. Press the Point ◄► buttons to move the red
frame pointer to the Input Menu icon.
Move the pointer (red
arrow) to Video and press
the SELECT button.
Press the Point ▲▼ buttons to move the red arrow
pointer to Video, and then press the SELECT button.
2
Video
Move the pointer to the desired source and then press
the SELECT button.
3
Source Select Menu (Video)
Move the pointer to the source
that you want to select and
press the SELECT button.
Note:
When the Input Search function is set On1 or On2,
the input signal will be searched automatically. (p.46)
37
Video Input
Input Source Selection (Component, RGB Scart 21-pin)
Direct Operation
Top Control
Choose Computer 2 by pressing the INPUT button on
the top control or press the COMPUTER 2 button on
the remote control. Choose Component by pressing
COMPONENT button on the remote control.
INPUT button
Before using these buttons, correct input source should be
selected through Menu operation as described below.
Computer 1 (Analog)
Computer 1 (Digital)
Computer 2
Video
Remote Control
COMPUTER 2 button
COMPONENT button
2
1
Input Menu
Menu Operation
Press the MENU button to display the On-Screen
Menu. Press the Point ◄► buttons to move the red
1
Move the pointer (red
arrow) to Computer 2 and
press the SELECT button.
frame pointer to the Input Menu icon.
Press the Point ▲▼ buttons to move the red arrow
pointer to Computer 2 and then press the SELECT
button.
2
Computer
2
After the Source Select Menu appeared for Computer
2, move the pointer to Component or RGB(Scart) and
then press the SELECT button.
3
Move the pointer to
Component or RGB(Scart)
and press the SELECT
button.
When the input source is coming from
video equipment connected to the
COMPUTER IN 2/COMPONENT IN
terminal with a Component-VGA Cable,
select Component.
Component
RGB (Scart)
Note:
When the input source is coming from
video equipment connected to the
COMPUTER IN 2/COMPONENT IN
terminal with a Scart-VGA Cable, select
RGB (Scart).
When the Input Search function is set to “On1” or
“On2”, the input signal will be searched automatically
(p.46).
38
Video Input
Video System Selection
Press the MENU button to display the On-Screen
Menu. Press the Point ◄►buttons to move the red
1
frame pointer to the AV System Menu icon.
Press the Point ▲▼ buttons to move the red arrow
pointer to the system that you want to select and then
press the SELECT button.
2
Video or S-video
AV System Menu (Video or S-video)
Auto
The projector automatically detects incoming video
system, and adjusts itself to optimize its performance.
When Video System is PAL-M or PAL-N, select system
manually.
AV System Menu icon
Selected system is
displayed.
PAL/SECAM/NTSC/NTSC4 43/PAL-M/PAL-N
If the projector cannot reproduce proper video image, it
is necessary to select a specific broadcast signal format
among PAL, SECAM, NTSC, NTSC 4.43, PAL-M, and
PAL-N.
Move the pointer to a
system and press the
SELECT button.
AV System Menu (Component)
Component
Auto
The projector automatically detects incoming video signal,
and adjusts itself to optimize its performance.
AV System Menu icon
Selected system is
displayed.
COMPONENT VIDEO SIGNAL FORMAT
If the projector cannot reproduce proper video image, it
is necessary to select a specific component video signal
format among 480i, 575i, 480p, 575p, 720p, 1035i, and
1080i.
Move the pointer to a
system and press the
SELECT button.
Note:
The AV System Menu cannot be selected when
selecting RGB (Scart).
3ꢀ
Video Input
Image Level Selection
Remote Control
Direct Operation
Select an image level among Dynamic, Standard, Cinema,
Blackboard (Green), Colorboard, Image 1, Image 2, Image
3, and Image 4 by pressing the IMAGE button on the
remote control.
IMAGE button
IMAGE button
Dynamic
Dynamic
Picture level suitable for viewing picture in a bright room.
Standard
Standard
Cinema
Normal picture level preset on this projector.
Cinema
Picture level adjusted for the picture with fine tone.
Blackboard (Green)
Colorboard
Blackboard (Green)
Picture level suitable for the image projected on a
blackboard. This is mainly effective on a green colored
board, not truly effective on a black colored board.
Image 1
Colorboard
At the time of simple projection on the colored wall, you
can get the close color image to the color image projected
on a white screen by selecting the similar color to the wall
color from the preset four colors.
Image 2
Image 3
Image 4
Image 1 ~ 4
User preset image in the Image Adjust Menu (pp.42-43).
40
Video Input
Image Select Menu icon
Menu Operation
Press the MENU button to display the On-Screen
Menu. Press the Point ◄► buttons to move the red
Image Select Menu
1
frame pointer to the Image Select Menu icon.
Press the Point ▲▼ buttons to move the red frame
pointer to the level that you want to set and then press
the SELECT button.
2
M o v e t h e r e d f r a m e
pointer to the level and
press the SELECT button.
Dynamic
Picture level suitable for viewing picture in a bright room.
Standard
Normal picture level preset on this projector.
Cinema
The level being selected.
Picture level adjusted for the picture with fine tone.
Blackboard (Green)
Picture level suitable for the image projected on a
blackboard. See above for further description.
Colorboard
At the time of simple projection on the colored wall, you
can get the close color image to the color image projected
on a white screen by selecting the similar color to the
wall color from the preset four colors. Press the SELECT
button to choose the color.
Image 1 ~ 4
User preset image in the Image Adjust Menu. (pp.42-43)
41
Video Input
Image Level Adjustment
Press the MENU button to display the On-Screen
Menu. Press the Point ◄► buttons to move the red
Image Adjust Menu
1
frame pointer to the Image Adjust Menu icon.
Press the Point ▲▼ buttons to move the red frame
Image Adjust Menu icon
Move the red frame
pointer to the item to be
selected and then press
the SELECT button.
2
pointer to the item that you want to adjust, and then
press the SELECT button. The level of each item is
displayed. Adjust each level by pressing the Point ◄►
buttons.
Contrast
Press the Point ◄ button to decrease the contrast and the
Point ► button to increase contrast. (From 0 to 63.)
Brightness
Press the Point ◄ button to adjust the image darker and
the Point ► button to adjust the image brighter. (From 0 to
63.)
Color
Press the Point ◄ button to lighten the color and the Point
► button to deepen the color. (From 0 to 63.)
Press the Point ◄►
buttons to adjust the
value.
Tint
Press the Point ◄► buttons to obtain a proper color.
(From 0 to 63.)
Color temp
Press the Point ◄ button or the Point ► button for Color
temp. level that you want to select.
(XLow, Low, Mid, or High)
White balance (Red)
Press the Point ◄ button to lighten the red tone and the
Point ► button to deepen the red tone.
(From 0 to 63.)
White balance (Green)
Press the Point ◄ button to lighten the green tone and the
Point ► button to deepen the green tone.
(From 0 to 63.)
White balance (Blue)
Press the Point ◄ button to lighten the blue tone and the
Point ► button to deepen the blue tone.
(From 0 to 63.)
Notes:
• The Tint cannot be selected when the video system is PAL, SECAM, PAL-M, or PAL-N.
• After adjusting any of the White balance Red, Green, or Blue, the Color temp. changes to "Adj.".
42
Video Input
Sharpness
Press the Point ◄ button to soften the image and the Point
► button to sharpen the image. (From 0 to 15.)
Gamma
Press the Point ◄► buttons to obtain better balance of
contrast. (From 0 to 15.)
Noise reduction
Noise interference on the screen can be reduced. Select
one of the following to get smoother images.
Off . . . . disabled.
L1. . . . . lower reduction
L2. . . . . higher reduction
Progressive
Interlaced video signal can be displayed in a progressive
picture. Select one of the following.
Off . . . . disabled.
L1. . . . . Select "L1" for an active picture.
L2. . . . . Select "L2" for a still picture.
Film . . . Select "Film" for watching a film. With this
function, the projector reproduces pictures
faithful to the original film quality.
Store item
Image Level Menu
Move the red frame pointer
to an image item to be set
and then press the SELECT
button.
Reset
To reset the adjusted data, select Reset and press the
SELECT button. The confirmation box appears and then
select [Yes]. All adjustments returns to their previous
figures.
The confirmation box
appears and then select
[Yes].
Store
To store the adjusted data, select Store and press the
SELECT button. Select a level from Image 1 to 4 with the
Point ▲▼ buttons and press the SELECT button.
A confirmation box appears and then select [Yes].
Stored data can be called up by selecting "Image" in the
Image Level Selection on pages 40-41.
Quit
Exit the Image Adjust Menu.
Note:
Noise reduction and Progressive cannot be selected
when 480p, 575p, 720p, 1035i, or 1080i is selected.
(p.39)
43
Video Input
Screen Size Adjustment
This projector has the picture screen resize function, which enables you to customize the image size.
Press the MENU button to display the On-Screen
Menu. Press the Point ◄► buttons to move the red
1
Screen Menu
frame pointer to the Screen Menu icon.
Press the Point ▲▼ buttons and move the red frame
pointer to the function that you want to select and then
2
Screen Menu icon
press the SELECT button.
Move the red frame pointer to a
function and press the SELECT
button.
Normal
Provide the image at a normal video aspect ratio of 4:3.
Wide
Provide the image at a wide screen ratio of 16:9.
Custom
Adjust the screen scale and position manually with this
function.
Press the SELECT button at Custom and the "Custom" is
displayed on the screen for a few seconds and then the
Aspect dialog box appears.
Scale H/V.................. Adjust the Horizontal/Vertical
screen scale.
H&V........................... When set to "On", the aspect ratio
is fixed. The "Scale V" appears
dimmed and becomes unavailable.
Adjust the "Scale H", then the
screen scale is automatically
modified based on the aspect
ratio.
Press the SELECT
button at Common
or Reset, to display
a confirmation box.
Position H/V .............. Adjust the Horizontal/Vertical
screen position.
Common ................... Save the adjusted scale to all
the inputs. Press the SELECT
button at Common to display a
confirmation box. To save the
scale, press the SELECT button at
"Yes". When Custom is selected,
the saved scale is used.
Reset......................... Reset the all adjusted values.
Press the SELECT button at Reset
to display a confirmation box. To
reset, press the SELECT button at
"Yes".
Notes:
• Wide cannot be operated when 720p,
1035i, or 1080i is selected in the AV
System Menu (p.39).
• When no signal is detected, "Normal" is
set automatically and the Aspect dialog
box disappears.
• The adjustable range for Scale H/V and
Position H/V is limited depending on the
input signal.
44
Setting
Setting
This projector has Setting menu that allows you to set up
the other various functions described as follows:
Setting Menu (Language)
Press the MENU button to display the On-Screen
Menu. Press the Point ◄► buttons to move the red
1
Setting Menu icon
frame pointer to the Setting Menu icon.
Set the red frame pointer
to the item and press the
SELECT button.
Press the Point ▲▼ buttons to move the red frame
pointer to the item that you want to set and then press
the SELECT button. The Setting dialog box appears.
2
Press the SELECT
button at Language
item, the Language
Menu appears.
Language
The language used in the On-Screen Menu is available in
English, German, French, Italian, Spanish, Portuguese,
Dutch, Swedish, Finnish, Polish, Hungarian, Romanian,
Russian, Chinese, Korean, or Japanese.
See the next pages for other items.
45
Setting
Auto setup
This function enables Input search, Auto Keystone
correction and Auto PC adjustment by pressing the AUTO
SETUP button on the top control or the AUTO SET button
on the remote control. Settings for those functions can be
altered as follows:
Input search
This function detects the input signal automatically. When
finding a signal, the search will stop. Use the Point ◄►
buttons to select one of the following.
S e l e c t A u t o s e t u p
and this box appears.
Choose the desired
setting for Input search,
Auto keystone and Auto
PC adj. with the Point ◄
► buttons.
Off . . . . Input search does not work.
On1 . . . Input search works under the situation below.
• When pressing the AUTO SETUP button on the top
control or the AUTO SET button on the remote control.
On2 . . . Input search works under the situation below.
• When turning on the projector with pressing the POWER
ON/STAND-BY button on the top control or on the remote
control.
• When pressing the AUTO SETUP button on the top
control or the AUTO SET button on the remote control.
• When missing the current input signal.
Notes:
• Input search, Auto PC Adj. and Auto
Keystone cannot be set "Off" at the
same time.
• Auto Keystone adjusts automatically
by pressing the AUTO SETUP button
either it is set on "Auto" or "Manual" in
setting menu.
• If the No show or Freeze function is active, cancel it to
activate the Input search. It is also unavailable when
On-Screen menu is displayed.
• While Input Search is set On1 or On2, the status of
Input and Lamp mode are displayed every time the
signal is switched.
• Auto Keystone corrects vertical
distortion only, not correct horizontal
distortion.
• If any of the COMPUTER 1/2, VIDEO, S-VIDEO
or COMPONENT buttons on the remote control, or
AUTO SETUP button on the top control is pressed
while Input search is on, Input search will stop.
• The Auto Keystone cannot work
when Ceiling feature is set "On" in the
Setting menu (p.50).
• Perfect correction of the image
distortion cannot be ensured with the
Auto setup function. If the distortion is
not corrected properly by pressing the
AUTO SETUP button, adjust manually
by pressing the KEYSTONE button
on the remote control or selecting
Keystone in the Setting menu (pp.22,
24, 47).
Auto PC Adj
On . . . . Enables Auto PC Adjustment when pressing the
AUTO SETUP button on the top control.
Off . . . . Disables Auto PC Adjustment.
Auto Keystone
Auto . . . Always works and corrects keystone distortion
according to the projector's tilt.
• Fine sync, Total dots, Horizontal and
Vertical position of some computers
cannot be fully adjusted with the Auto
PC Adjustment function. When the
image is not provided properly with
this operation, manual adjustments are
required (pp.29–30).
Manual . Works only when pressing the AUTO SETUP
button on the top control or the AUTO SET
button on the remote control.
Off . . . . Disables Auto Keystone.
46
Setting
Keystone
This function corrects distortion of a projected image.
Select either Store or Reset with the Point ◄► buttons,
and then press the SELECT button. The keystone dialog
box appears. Correct keystone with the Point ▲▼ buttons.
see page 22.
Store . . . . store the keystone correction even when the
AC power cord is unplugged.
Reset . . . . reset the keystone correction when the AC
power cord is unplugged.
Blue back
Press the Point ◄► buttons to switch On/Off. When this
function is "On", a blue image is displayed while the input
signal is not detected.
Display
Press the Point ◄► buttons to switch Off/Countdown off/
On. This function decides to display On-Screen Displays.
Off. . . . . . . . . . . . . Do not show On-Screen Displays,
except.
Countdown off . . . Show the input image instead of
the countdown when turning on the
projector. Use this function when you
want to project the image as early as
possible even when the lamp is not
bright enough.
On. . . . . . . . . . . . . Show all the On-Screen Displays.
Use this function when you want
to project images after the lamp
becomes bright enough. Factory
default setting is this mode.
● On-Screen Menu
● "Power off?" message
● P-Timer
● "No signal" message for Power management item
(p.50)
● "Please wait ..." for Auto PC adjustment.
● Arrows for panning mode in the Screen Menu (p.34).
47
Setting
Logo (Logo and Logo PIN code lock settings)
This function allows you to customize the screen logo with
Logo select, Capture, and Logo PIN code lock functions.
Note:
When On is selected in Logo PIN code lock function,
Logo select and Capture functions cannot be
selected.
Logo select
Logo select
This function decides the start-up display as follows:
User. . . . the image you captured
Default. . the factory-set logo
Off . . . . . countdown only
Capture
This function enables you to capture the image being
projected and use it for a start-up display or interval of
presentations.
After capturing the projected image, go to the Logo
select function and set it to "User". Then the captured
image is displayed when turning on the projector next
time or pressing the NO SHOW button. (p.24)
To capture the image, select [Yes]. To cancel the
Capture function, select [No].
Capture
Notes:
• Before capturing an image, select Standard in the
Image Select Menu to capture a proper image.
(pp.31-32, 40-41)
• A signal from a computer can be captured up to
XGA (1024x768). A signal from video equipment
can be captured except for 720p, 1035i, and
1080i.
Select [Yes] to capture
the projected image.
• When capturing the image that has been adjusted
by the Keystone function, the adjustment data is
automatically reset and the projector captures an
image without keystone adjustment.
Select [Yes] to
stop capturing.
• When the Logo PIN code lock function is "On",
Capture menu cannot be selected.
• When starting to capture a new image, the
previously stored image is cleared even if you
cancel the capturing.
• "User" cannot be selected when the image is not
captured.
48
Setting
Logo PIN code lock
Logo PIN code lock
This function prevents an unauthorized person from
changing the screen logo.
Off . . . . . . the screen logo can be changed freely from
the Logo select menu. (p.48)
On . . . . . . the screen logo cannot be changed without
the Logo PIN code.
If you want to change the Logo PIN code lock setting,
enter a Logo PIN code along the following steps. The
initial Logo PIN code is set "4321" at the factory.
To Enter the Logo PIN code
Select a number by pressing the Point ▲▼ buttons. And
then press the Point ►button to fix the number and move
the pointer. The number changes to "". If you fixed
an incorrect number, move the pointer to the number
you want to correct by pressing the Point ◄ button, and
then select the correct number by pressing the Point ▲▼
buttons.
Logo PIN code lock Dialog Box
Repeat this step to complete entering a four-digit number.
After a correct Logo PIN code is entered, the
following dialog box appears.
After entering the four-digit number, move the pointer to
"Set" by pressing the Point ►button. Press the SELECT
button so that you can change the Logo PIN code lock
setting.
If you entered an incorrect Logo PIN code, "Logo PIN
code" and the number () turns red. Enter a correct
Logo PIN code all over again.
Select On/Off by pressing the Point ◄► buttons or
change the Logo PIN code.
To Change the Logo PIN code
Logo PIN code can be changed to your desired four-digit
number. Select "Logo PIN code change" with the Point
▼button and press the SELECT button. Set a new Logo
PIN code.
Be sure to note the new Logo PIN code and keep it on
hand. If you lost the number, you could no longer change
the Logo PIN code setting. For details on PIN code
setting, refer to relevant instructions of the PIN code lock
function on pages 53 and 54.
CAUTION:
WHEN yOU HAVE CHANGED THE LOGO PIN CODE,
WRITE DOWN THE NEW PIN CODE IN COLUMN OF
THE LOGO PIN CODE NO MEMO ON PAGE 7ꢀ, AND
KEEP IT SECURELy SHOULD THE LOGO PIN CODE
BE LOST OR FORGOTTEN, THE PROjECTOR CAN NO
LONGER BE OPERATED
4ꢀ
Setting
Ceiling
Ceiling
When this function is "On", the picture is top/bottom and
left/right reversed. This function is used to project the
image from a ceiling mounting the projector.
Rear
When this function is "On", the picture is left/right reversed.
This function is used to project the image to a rear
projection screen.
Rear
Standby mode
This function is available when the projector is turned off
and in Stand-by. It is recommended to use Eco under
normal condition.
Normal . . . . . . . . . . normal power consumption in
Stand-by condition.
Eco. . . . . . . . . . . . . lower power consumption than
Normal mode in Stand-by condition.
Power management
Power management
For reducing power consumption as well as maintaining
the lamp life, the Power management function turns off the
projection lamp when the projector is not used for a certain
period.
When the input signal is interrupted and no button is
pressed for more than 30 seconds, the timer display with
"No signal" appears. The countdown starts to turn off the
lamp.
Time left before Lamp is off.
Select one of the operations:
Ready. . . . . . . . When the lamp has been fully cooled
down, the POWER indicator changes
to green blinking. In this condition, the
projection lamp is turned on if the input
signal is reconnected or any button
on the top control or remote control is
pressed.
Press the SELECT button
at Power management
and this box appears.
Choose one of three
settings with the Point ◄
Shut down . . . . When the lamp has been fully cooled
down, the power is turned off.
Off . . . . . . . . . . Power management function is off.
► buttons, and go to the
timer with the Point ▲▼
buttons and set time with
the Point ◄►buttons.
Then set the countdown timer with the Point ◄►buttons.
Note:
Factory default is " Ready, 5 min".
50
Setting
On start
On start
When this function is "On", the projector is automatically
turned on just by connecting the AC power cord to a wall
outlet.
Note:
Be sure to turn the projector off properly (see "Turning
Off the Projector" on page 19). If the projector is
turned off in the incorrect sequence, the On start
function does not operate properly.
Closed Caption
Closed Caption
Closed Caption is a function that displays the audio portion
of a TV program as text on the screen. If the input signal
contains closed captions, you can turn on the feature and
switch the channels. Press the Point ◄► buttons to select
CC1, CC2, CC3 or CC4.
If the closed caption is not clear, you can change the text
from Color to White.
Notes:
The Closed Caption is available only under the
situation below.
• When the input signal is NTSC of composite and
S-video, and the system is set according to the
signal or set on "Auto".
• The system must be set on NTSC or Auto in Video
System Selection. (P.39)
• The icon of Closed Caption is displayed in gray
while it is not available.
• The closed caption is unavailable when On-Screen
menu and P-Timer are displayed.
Lamp control
This function allows you to change brightness of the
screen.
Normal. . . . . normal brightness
Auto . . . . . . . brightness according with the input
signal
Eco . . . . . . . lower brightness reduces the lamp
power consumption and extends the
lamp life.
Note:
Lamp mode cannot be changed for a while after
turning on the projector. Lamp needs some time to
stabilize after the power is turned on. Stored lamp
mode will be active after the lamp is stabilized.
51
Setting
Filter control
Filter control
You can replace the filter with this function. Press the
SELECT button at Filter control to display a confirmation
box. To replace, press the SELECT button at “YES” and
the electrically operated filter starts to scroll.
Note:
• Filter replacement icon and “Please wait...”
message appear on the screen when the filter
is being scrolled.
• The filter cannot be rewound.
• When the filter is replaced, the total accumulatedtime
of the filter use is automatically set to 0.
Move the red frame pointer to
"filter control" and press the
SELECT button.
Remote control
This projector provides two different remote control codes:
the factory-set initial code (Code 1) and the secondary
code (Code 2). This switching function prevents remote
control interference when operating several projectors or
video equipment at the same time.
When operating the projector in "Code 2", both the
projector and the remote control must be switched to
"Code 2".
Remote control
Press and hold
M E N U a n d
IMAGE buttons
for more than 5
seconds.
To change the code for the projector:
Select either "Code 1" or "Code 2" in this Setting Menu.
To change the code for the remote control:
Press and hold both the MENU and IMAGE buttons
together for 5 seconds or more. After changing the code,
make sure the remote control operates properly.
Note:
If the batteries are removed from the remote control
for a long period of time, the remote control code will
be reset.
52
Setting
Security (Key lock and PIN code lock settings)
Key lock
This function allows you to use Key lock and PIN code
lock function to set the security for the projector operation.
Key lock
This function locks operation of the top control or the
remote control.
It is useful to prevent operation by an unauthorized
person.
. . . . . . not locked.
. . . . . . lock the operation of the top
control. To unlock, use the
remote control.
. . . . . . lock the operation of the remote
control. To unlock, use the top
control.
Select Key lock.
Choose one of
the alternatives
with the Point ▲
▼ buttons and
select [Yes] to
activate it.
If the top control accidentally becomes locked and you
do not have the remote control or there is something
wrong with your remote control, contact the dealer
where you purchased the projector or the service
center.
PIN code lock
This function prevents the projector from being
operated by an unauthorized person and provides the
following settings for security options.
PIN code lock
Off . . . . . the projector is not locked with a
PIN code.
On1 . . . . require to enter a PIN code every time
turning on the projector.
On2 . . . . require to enter a PIN code to operate
the projector once the power cord is
disconnected; as long as the AC power
cord is connected, the projector can be
operated without a PIN code.
Whenever to change the PIN code lock setting or the
PIN code (the four-digit number), you are required to
enter the PIN code. The "1234" is set as the initial PIN
code at the factory.
When the projector is locked
with the PIN code, the PIN
code lock mark appears on
the menu bar.
53
Setting
Enter a PIN code
To Enter the PIN code
Select a number by pressing the Point ▲▼ buttons. And
then press the Point ►button to fix the number and move
the pointer. The number changes to "". If you fixed
an incorrect number, move the pointer to the number
you want to correct by pressing the Point ◄ button, and
then select the correct number by pressing the Point ▲▼
buttons.
Repeat this step to complete entering a four-digit number.
After entering the four-digit number, move the pointer to
"Set" by pressing the Point ►button. Press the SELECT
button so that you can change the following PIN code lock
settings.
The input numbers change
to "" for security.
If you entered an incorrect PIN code, "PIN code" and the
number () turns red. Enter a correct PIN code all
over again.
To Change the PIN code lock setting
Select Off, On1, or On2 with the Point ◄► buttons and
then move the red frame pointer to "Quit" with the Point ▼
button. Press the SELECT button to close the dialog box.
Move the pointer to "Set" by pressing
the Point ► button. And then press
To Change the PIN code
the SELECT button.
The PIN code can be changed to your desired four-digit
number.
Change the PIN code lock setting
Select "PIN code change" with the Point ▼ button, and
press the SELECT button to display the New PIN code
input dialog box.
Select a number by pressing the Point ▲▼ buttons. And
then press the Point ►button to fix the number and move
Select a desired setting with the
Point ◄► buttons.
the pointer. Repeat it to complete entering a four-digit
number. After entering the four-digit number, move the
pointer to "Set" by pressing the Point ►button. Then press
Change the PIN code
the SELECT button.
CAUTION:
WHEN yOU HAVE CHANGED THE PIN CODE, WRITE
DOWN THE NEW PIN CODE IN COLUMN OF THE
PIN CODE NO MEMO ON PAGE 7ꢀ, AND KEEP IT
SECURELy IF yOU FORGET yOUR PIN CODE, THE
PROjECTOR CAN NO LONGER BE STARTED
Select PIN code change and
press the SELECT button. The
New PIN code input dialog box
appears.
The input numbers are being
displayed for confirmation.
54
Setting
Fan
This function provides the following alternatives in the
cooling fans' operation after turning off the projector. (p.19)
L1. . . . . . normal operation
L2. . . . . . slower and lower-sound than the normal
operation (L1), but it takes longer to cool the
projector down.
Warning log
This function records anomalous operations while the
projector is in operation and use it when diagnosing faults.
Up to 10 warning logs are displayed with the latest warning
message at the top of the list, followed by previous warning
messages in chronological order.
Note:
When the Factory default function is executed, all the
warning log records will be deleted.
Lamp counter
Lamp replacement icon
This function is used to reset the lamp replacement
counter. When replacing the projection lamp, reset the
lamp replacement counter by using this function. See
page 62 for operation.
This icon appears on the screen when the
end of lamp life is reached.
Note:
Do not reset the Lamp replacement counter without
implementation of lamp replacement. Be sure to
reset the Lamp replacement counter only after
replacing the lamp.
Note:
This icon also appears at turning on and
selecting input source.
55
Setting
Filter counter
Filter counter
This function is used to set a frequency for the filter
replacement.
Use the Point ▲▼ buttons to move the red frame pointer
to Filter counter and then press the SELECT button.
A dialog box appears showing the Used time option and
the Scrolls remaining option.
Set the red frame pointer
to the item and press the
SELECT button.
Used Time . . . . . . . . Show the total accumulated time
of the filter use, timer setting option and the
Reset options. When the projector reaches
a time set in the timer setting, the Filter
replacement icon (Fig. 1) appears on the
screen and the total accumulated time turns
red, indicating that the filter replacement is
necessary. If the filter is out of scroll and
the projector reaches a time set in the
timer setting, Fig. 2 appears on the screen,
indicating that the filter cartridge replacement
is necessary.
Use the Point ◄► buttons to
set the timer. Select from (Off/
400H/700H/1000H) depending
on the use environment.
Fig.1 Filter replacement icon
Filter replacement icon appears on
the screen at a set time.
Scrolls remaining. . . . Show the scroll counter and
the Reset options. When the filter scroll is
counted down to 1 (Scroll counter on the
screen is showing “0 scroll(s)” ), the last scroll
icon (Fig. 3) appears on the screen. When
the filter scroll is counted down to 0, the Filter
cartridge replacement icon (Fig. 4) appears
on the screen and the WARNING FILTER
indicator lights orange, indicating that the filter
cartridge replacement is necessary.
Fig.2
Fig.3 Last scroll icon
Last scroll icon appears on the screen
when the filter is down to the last scroll.
Fig.4 Filter cartridge replacement icon
Filter cartridge replacement icon
appears on the screen when the filter
scroll is counted down to 0 scroll.
To set a timer, press the SELECT button on Used time
option. Move the red arrow pointer to the timer setting
option and use the Point ◄►buttons to select from (Off/
400H/700H/1000H) depending on the use environment.
When replacing the Filter cartridge, reset the Filter
counter and the Scroll counter (p.59).
Note:
• Fig.1, Fig. 2, Fig. 3 and Fig. 4 appear at
turning on and selecting input source.
• Fig.1, Fig. 2, Fig. 3 and Fig. 4 will not appear
when the Display function is set to “Off”
(p.47), during “Freeze” (p.23), or “No show”
(p.24).
Note:
• Do not reset the counter(s) when the filter or the filter cartridge
are not replaced.
• Timer setting notifies that the filter needs replacement. To replace
the filter, use the filter control function (p.52).
Factory default
Factory default
Factory default
Select Factory default and this
box appears. Select [Yes], and
the next box appears.
This function returns all setting values except for the user
logo, PIN code lock, Logo PIN code lock, and the lamp
counter to the factory default settings.
Quit
Exit the Setting Menu.
Select [Yes] to
activate it.
56
Maintenance and Care
Filter Instructions
Filter prevents dust from accumulating on the optical elements inside the projector. Should the filter
becomes clogged with dust particles, it will reduce cooling fans’ effectiveness and may result in internal heat
buildup and adversely affect the life of the projector. This projector has an electrically operated filter which
helps you to replace the filter easily. The projector monitors the condition of the filter at all time and replaces
a filter with a new one automatically when it detects the clogging.
If the projector reaches a time set in the timer setting (p.56), a
Filter replacement icon (Fig.1) appears on the screen and the
WARNING FILTER indicator on the top control lights up . When
you see this icon, replace the filter as soon as possible (p.52).
If the filter is out of scroll and the projector reaches a time set in
the timer setting, Fig. 2 appears on the screen, indicating that
the filter cartridge replacement is necessary.
Fig.1 Filter replacement icon
When the filter scroll is counted down to 1, the Last scroll icon
(Fig.3) appears on the screen, indicating that there is one scroll
left in the filter cartridge (p.56).
Fig.2
If the projector detects that the filter is clogged and no scroll
is left in the filter cartridge, a Filter cartridge replacement icon
(Fig. 4) appears on the screen and the WARNING FILTER
indicator on the top control lights up . When you see this icon,
replace the filter cartridge (p.58) and reset the Filter counter
(p.59) and the Scroll counter (p.59).
Fig.3 Last scroll icon
Fig.4 Filter cartridge replacement icon
When the filter is being scrolled using the Filter control function
in the setting menu (p.52), a Filter replacement icon and
“Please wait...” message (Fig.5) appear on the screen and the
WARNING FILTER indicator blinks slow (approx. 2 seconds
ON, 2 seconds OFF).
Fig.5 Filter replacement icon and “Please
wait...” message.
The WARNING FILTER indicator blinks fast when the projector
detects an abnormal condition, the filter cartridge is not
installed properly, or the filter scroll is not working properly .
Note:
• Fig.1, Fig.2, Fig.3, Fig. 4 and Fig.5 will not appear when the
Display function is set to “Off” (p.47), during “Freeze” (p.23),
or “No show” (p.24).
•
•
Make sure that the projection lamp is turn off
when you are replacing the filter cartridge.
If you replace the filter cartridge when the
projection lamp is turn on, the projector will be
shut down automatically for safety purpose.
When you forget to reset the filter counter,
the projector cannot recognize the correct
number of remaining scrolls and may cause a
breakdown.
• The filter cannot be rewinded.
• The filter can be scrolled 9 times since the filter cartridge has
10 scrolls.
• The filter cartridge is disposable. Do not clean and reuse the
filter cartridge.
• Do not expose the filter cartridge to water or liquid, or it may
cause a breakdown.
• Replace the filter cartridge after all the scroll is used up. If
you replace the filter cartridge when there are some scrolls
left in the filter cartridge, the filter counter and the scroll
counter do not recognize the correct number of remaining
scrolls and the reset function cannot work properly. It may
cause a breakdown.
• Do not use the filter cartridge with other projector. The filter
counter and the scroll counter do not recognize the correct
number of remaining scrolls of the used filter cartridge and
the reset function cannot work properly. It may cause a
breakdown.
• Do not forget to reset the filter counter and the
scroll counter in the setting menu after replacing
the filter cartridge. If you forget to reset the filter
counter and the scroll counter, the projector cannot
recognize the correct number of remaining scrolls
and may cause a breakdown.
• When the projector is kept used for 3 minutes
without getting the filter cartridge replaced
after the Fig.4 appears on the screen, the
projector is turned off automatically to prevent
the damage of optical components.
57
Maintenance and Care
Replacing the Filter Cartridge
Filter cover
Turn off the projector, and unplug the AC power cord from
the AC outlet.
1
First, clean up the dust on the projector and around the air
vents.
2
Loosen 2 screws of the filter cover with a screwdriver and
open the filter cover.
3
Rotate the handle of the filter and pull out the filter
cartridge.
4
Put the new one back into the position and rotate back
Screws
5
the handle. Make sure that the filter cartridge is properly
and fully inserted. Close the filter cover and tighten the 2
screws back into position.
Connect the AC power cord to the projector and turn on the
projector.
6
Reset the filter counter and the scroll counter (p.59).
7
CLOSE
CAUTION
Make sure the filter cartridge is inserted in the projector.
If the filter cartridge is not inserted, the projector cannot
be turned on.
handle
Do not put anything into the air vents. Doing so may
result in malfunction of the projector.
RECOMMENDATION
We recommend avoiding dusty/smoky environments when
operating the projector. Usage in these environments may
cause a poor image quality.
OPEN
When using the projector under dusty or smoky conditions,
dust may accumulate on a lens, liquid crystal panels, or
optical elements inside the projector. Such condition may
degrade the quality of the projected image.
When the symptoms above are noticed, contact your
authorized dealer or service station for proper cleaning.
handle
ORDER REPLACEMENT FILTER CARTRIDGE
Filter cartridge
Replacement filter cartridge can be ordered through
your dealer. When ordering, give the following
information to the dealer.
●
●
Model No. of your projector
LC-XS25/LC-XS30
Replacement Filter Cartridge
Service Parts No. 610 339 7665
58
Maintenance and Care
Resetting the Filter Counter
Filter counter
Be sure to reset the Filter counter after replacing the filter
cartridge.
Press the MENU button to display the On-Screen
1
Menu. Use the Point ◄► buttons to move the red
frame pointer to the Setting Menu icon.
Set the red frame pointer
to the item and press the
SELECT button.
Use the Point ▲▼buttons to move the red frame
2
pointer to Filter counter and then press the SELECT
button. A dialog box appears showing the Used time
option and the Scrolls remaining option. Use the
Point ▲▼ buttons to select Used time.
Select Reset and
the “Filter counter
Reset?” appears.
Used time shows the total accumulated time of
3
the filter use, a timer setting option, and the Reset
option. Select Reset and the “Filter counter Reset?”
appears. Select [Yes] to continue.
S e l e c t [ Ye s ] ,
t h e n a n o t h e r
confirmation box
appears.
Another confirmation dialog box appears, select
[Yes] to reset the Filter counter.
4
Select [Yes] again
to reset the Filter
counter.
Resetting the Scroll Counter
Be sure to reset the Scroll counter after replacing the filter cartridge.
Press the MENU button to display the On-Screen
Menu. Use the Point ◄► buttons to move the red
frame pointer to the Setting Menu icon.
Scroll counter
1
2
Use the Point ▲▼ buttons to move the red frame
pointer to Filter counter and then press the SELECT
button. A dialog box appears showing the Used time
option and the Scrolls remaining option. Use the
Point ▲▼ buttons to select Scroll(s) remaining.
Set the red frame pointer
to the item and press the
SELECT button.
Scroll(s) remaining shows the number of the
remaining scrolls and the Reset option. Select
Reset and the “Scroll counter Reset?” appears.
Select [Yes] to continue.
3
4
Select Reset and
the “Scroll counter
Reset?” appears.
Another confirmation dialog box appears, select
[Yes] to reset the Scroll counter.
S e l e c t [ Ye s ] ,
t h e n a n o t h e r
confirmation box
appears.
Select [Yes] again
to reset the Scroll
counter.
5ꢀ
Maintenance and Care
Lamp Replacement
When the life of the projection lamp of this projector
draws to an end, the Lamp replacement icon appears on
the screen and LAMP REPLACE indicator lights yellow.
Replace the lamp with a new one promptly. The timing
when the LAMP REPLACE indicator should light is
depending on the lamp mode.
Top Control
This indicator is yellow
when the life of the
projection lamp draws to
an end.
Lamp replacement icon
Note:
The Lamp replacement icon will not
appear when the Display function is set
to “Off” (p.47), during “Freeze” (p.23), or
“No show” (p.24).
CAUTION
Allow a projector to cool, for at least 45 minutes before you open the Lamp cover. The inside of the
projector can become very hot.
CAUTION
For continued safety, replace with a lamp of the same type. Do not drop a lamp or touch a glass
bulb! The glass can shatter and may cause injury.
CAUTION
When replacing the lamp because it has stopped illuminating, there is a possibility that the lamp may
be broken.
If replacing the lamp of a projector which has been installed on the ceiling, you should always
assume that the lamp is broken, and you should stand to the side of the lamp cover, not underneath
it. Remove the lamp cover gently. Small pieces of glass may fall out when the lamp cover is opened.
If pieces of glass get into your eyes or mouth, seek medical advice immediately.
Refer to the next page for replacing a lamp.
60
Maintenance and Care
Lamp Cover
Follow these steps to replace the lamp.
Turn off the projector and disconnect the AC power
cord. Allow the projector to cool for at least 45
minutes.
1
Loosen the screw with a screwdriver, slide and open
the lamp cover.
2
Loosen 2 screws of the lamp with a screwdriver and
pull out the lamp upwards vertically by grasping the
handle.
3
Replace the lamp with a new one and tighten the 2
4
screws back into position. Make sure that the lamp is
set properly. Replace the lamp cover and tighten the
screw.
Screw
Handle
Screw
Connect the AC power cord to the projector and turn
on the projector.
5
Reset the lamp replacement counter
See "Resetting the Lamp Counter" on the next page .
6
Screw
Lamp
ORDER REPLACEMENT LAMP
Replacement lamp can be ordered through your dealer. When ordering a projection lamp, give
the following information to the dealer.
● Model No. of your projector
● Replacement Lamp Type No.
: LC-XS25/LC-XS30
: POA-LMP127
(Service Parts No. 610 339 8600)
61
Maintenance and Care
Resetting the Lamp Counter
Be sure to reset the Lamp replacement counter after the lamp is replaced. When the Lamp replacement
counter is reset, the LAMP REPLACE indicator stops lighting.
Turn the projector on, press the MENU button to
1
To reset the lamp counter, move the
display the On-Screen Menu. Press the Point ◄►
pointer to Reset and then press the
buttons to move the red frame pointer to the Setting
Menu icon.
SELECT button. “Lamp replacement
counter Reset?” dialog box is displayed.
Press the Point ▲▼ buttons to move the red frame
pointer to the Lamp counter function and then press
the SELECT button. The first dialog box appears and
shows the total accumulated time of the lamp usage
and the reset option. If you select "Reset", a "Lamp
replacement counter Reset?" message appears.
Select [Yes] to continue.
2
Another confirmation dialog box appears, select [Yes]
to reset the Lamp replacement counter.
3
Select [Yes],
then another
confirmation
Note:
box appears.
Do not reset the Lamp replacement counter without
implementation of lamp replacement. Be sure to reset
the Lamp replacement counter only after replacing the
lamp.
Select [Yes] again
to reset the lamp
counter.
LAMP HANDLING PRECAUTIONS
This projector uses a high-pressure lamp which must be handled carefully and properly.
Improper handling may result in accidents, injury, or create a fire hazard.
● Lamp life may differ from lamp to lamp and according to the environment of use. There is no guarantee of
the same life for each lamp. Some lamps may fail or terminate their life in a shorter period of time than other
similar lamps.
● If the projector indicates that the lamp should be replaced, i.e., if the LAMP REPLACE indicator lights up,
replace the lamp with a new one IMMEDIATELY after the projector has cooled down. (Follow carefully the
instructions in the Lamp Replacement section of this manual.) Continuous use of the lamp with the LAMP
REPLACE indicator lighted may increase the risk of lamp explosion.
● A Lamp may explode as a result of vibration, shock or degradation as a result of hours of use as its lifetime
draws to an end. Risk of explosion may differ according to the environment or conditions in which the projector
and lamp are being used.
IF A LAMP EXPLODES, THE FOLLOWING SAFETy PRECAUTIONS SHOULD BE TAKEN
If a lamp explodes, disconnect the projector's AC plug from the AC outlet immediately. Contact an authorized
service station for a checkup of the unit and replacement of the lamp. Additionally, check carefully to ensure that
there are no broken shards or pieces of glass around the projector or coming out from the cooling air circulation
holes. Any broken shards found should be cleaned up carefully. No one should check the inside of the projector
except those who are authorized trained technicians and who are familiar with projector service. Inappropriate
attempts to service the unit by anyone, especially those who are not appropriately trained to do so, may result in
an accident or injury caused by pieces of broken glass.
62
Maintenance and Care
WARNING TEMP indicator
The WARNING TEMP. indicator shows the state of the function which protects the projector. Check the state
of the WARNING TEMP. indicator and the POWER indicator to take proper maintenance.
The projector is shut down and the WARNING TEMP
indicator is blinking red
Top Control
WARNING TEMP.
blinking red
When the temperature inside the projector reaches a
certain level, the projector is automatically shut down to
protect the inside of the projector. The POWER indicator
is blinking while the projector is being cooled down. When
the projector has cooled down sufficiently (to its normal
operating temperature), it can be turned on again by
pressing the POWER ON/STAND-BY button.
Note:
After the temperature inside the projector returns to
normal, the WARNING TEMP. indicator still continues
to blink. When the projector is turned on again, the
WARNING TEMP. indicator stops blinking.
Then check the matters below:
– Did you provide appropriate space for the projector to
be ventilated? Check the installing condition to see if
ventilation slots are not blocked.
– Is the projector not installed near the ventilation duct of
air-conditioning equipment which may be hot? Install
the projector away from the ventilation duct of air-
conditioning equipment.
– Is the air filter clean? Replace the filter periodically.
(p.52)
The projector is shut down and the WARNING TEMP
indicator emits a red light
Top Control
When the projector detects an abnormal condition, it is
automatically shut down to protect the inside and the
WARNING TEMP. indicator becomes red. In this case,
disconnect the AC power cord and reconnect it, and then
turn the projector on once again for check. If the projector
cannot be turned on and the WARNING TEMP. indicator
emits a red light, disconnect the AC power cord and
contact the service station for check and repair.
WARNING TEMP.
lights red
CAUTION
DO NOT LEAVE THE PROJECTOR WITH THE
AC POWER CORD CONNECTED UNDER THE
ABNORMAL CONDITION. IT MAY RESULT IN
FIRE OR ELECTRIC SHOCK.
63
Maintenance and Care
Cleaning the Lens Cover
Follow these steps to clean the lens cover.
Disconnect the AC power cord before cleaning.
1
Softly wipe the lens cover with a cleaning cloth that
2
contains a small amount of non-abrasive camera lens
cleaner, or use lens cleaning paper or a commercially
available air blower to clean the lens. Avoid using
an excessive amount of cleaner. Abrasive cleaners,
solvent, or other harsh chemicals might scratch the
surface.
Cleaning the Projector Cabinet
Follow these steps to clean the projector cabinet.
Disconnect the AC power cord before cleaning.
1
Softly wipe the projector body with a soft, dry cleaning
2
cloth. When it is heavily soiled, use a small amount of
mild detergent and finish with a soft, dry cleaning cloth.
Avoid using an excessive amount of cleaner. Abrasive
cleaners, solvent, or other harsh chemicals might
scratch the surface.
When the projector is not in use, put the projector in
an appropriate carrying case to protect it from dust and
scratches.
3
64
Appendix
Troubleshooting
Before calling your dealer or service center for assistance, check the items below once again.
– Make sure you have properly connected the projector to peripheral equipment as described on
pages14-16.
– Make sure all equipment is connected to AC outlet and the power is turned on.
– When you operate the projector with a computer and it does not project an image, restart the computer.
Problem
– Solutions
No power
– Plug the power cord of the projector into the AC outlet.
– See if the POWER indicator lights red.
– Wait until the POWER indicator stops blinking to turn on the
projector again. The projector can be turned on after the POWER
indicator turns red. (See page 18.)
– Check the WARNING TEMP. indicator. If the WARNING TEMP.
indicator lights red, the projector cannot be turned on.
(See page 63.)
– Check the projection lamp. (See page 60.)
– Unlock the Key lock function. (See page 53.)
– See if the filter cartridge is inserted.
The initial display is not shown
– Make sure "Off" or "Countdown off" are not chosen at Display
function.(see page 47)
The initial display is not same as
– Make sure "User" or "Off" are not chosen at Logo (select) as the
default set. (see page 48)
the default set
Input signal switches
automatically (or does not
switch automatically)
– Make sure Input search function is adjusted properly. (See page
46)
Image is out of focus
– Adjust the focus of the projector. (See page 22.)
– Provide proper distance between the projector and the projection
screen. (See page 13.)
– Check the lens cover to see if it needs cleaning. (See page 64.)
– Moving the projector from a cool to warm place may result in
moisture condensation on the projection lens. If this occurs, leave
the projector off and wait until condensation evaporates.
No image
– Check the connection between your computer or video equipment
and the projector. (See pages 14-16.)
– See if the input signal is correctly output from your computer.
For some laptop computers, you may need to change the setting
for the monitor output when connecting to a projector. See your
computer’s instruction manual for the setting.
– It takes about 30 seconds to display an image after turning on
the projector. See if the selected system is corresponding to your
computer or video equipment. (See pages 27 and 39.)
– Select a correct input source once again through menu operation.
(See pages 25,26, 37 and 38.)
– Make sure the temperature is not out of the specified operating
temperature (41°F ~ 95°F[5°C ~ 35°C]).
65
Appendix
Image is Left/Right reversed
Image is Top/Bottom reversed
– Check the Ceiling/Rear function. (See page 50.)
– Check the Ceiling function. (See page 50.)
No sound
– Check audio cable connections from the audio input source.
– Adjust the audio source.
– Press the VOLUME + button. (See page 23.)
– Press the MUTE button. (See page 23.)
– Is the image projected? You will hear the sound only when the
image is projected.
The color is strange
– Check the Input signal, color system, video system or computer
system mode.
– Make sure the "Blackboard" or "Colorboard" is not selected on
Image select menu. (see pages 31, 32, 40, 41.)
Some displays are not seen
during operations
– Check the Display item. (See page 47.)
Auto PC adjustment function
does not work
– Check the Input signal. Auto PC function can not work when
480p, 575p, 720p, 480i, 575i, 1035i or 1080i is selected, or digital
signal is input into DVI terminal. (see Page 28)
The setting does not remain after
turning off power
– Make sure you select "Store" after adjusting setting. Some settings
can not be stored if not registered with "Store". (see pages 30, 43)
Power management does not
work
– Power management function can not work while "Freeze" or "No
Show" function is running. (see pages 23,24)
Capture function does not work
– Check the connection and the input signal to see if there is signal.
Auto setup does not work
properly
– Make sure "Off" is not selected at any function of "Auto setup". (see
page 46)
– Make sure "On" is not selected at the Ceiling function. (see page
50)
Auto keystone does not work
properly even when the projector
is tipped
– Make sure the Auto keystone function is not set to "Manual". Press
the AUTO SETUP button on the top control or the AUTO SET
button on the remote control. (see pages 22, 46)
The image is distorted or runs
off
– Check PC adjustment menu or Screen menu and adjust them.
(see pages 29-30, 34-35)
PIN code dialog box appears at
the start-up
– PIN code lock is being set. Input a PIN code (1234 or numbers you
have set). (See pages 18, 53 and 54.)
66
Appendix
The Remote Control does not
– Check the batteries.
– Make sure there is no obstruction between the projector and
remote control.
work
– Make sure you are not too far from the projector when using the
remote control. Maximum operating range is 16.4' (5 m).
– Make sure the code of the remote control is conformed to that of
the projector. (See page 52.)
– Unlock the Key lock function for the remote control. (See page 53.)
Indicator blinks or lights
– Check the status of the projector with referring to "Indicators and
projector Condition". (see page 71-72 )
The exclamation mark appears
on the screen
– Your operation is invalid. Operate correctly.
The Top Control does not work
– Unlock the Key lock function for the top control of the projector.
Unable to unlock the Logo PIN
code lock, Security key lock or
Security PIN code lock
– Contact the dealer where you purchased the projector or the
service center.
WARNING:
High voltages are used to operate this projector Do not attempt to open the cabinet
If problems still persist after following all operating instructions, contact the dealer where you purchased the
projector or the service center. Give the model number and explain about the problem. We will advise you
how to obtain service.
This symbol on the nameplate means
The CE Mark is a Directive
the product is Listed by Underwriters
conformity mark of the
Laboratories Inc. It is designed and
European Community (EC).
manufactured to meet rigid U.L. safety
standards against risk of fire, casualty and
electrical hazards.
67
Appendix
Menu Tree
Computer Input/Video Input
Computer 1 (Analog)
Go to System (1)
Input
Computer 1 (Digital)
Computer 2
RGB (PC digital)
RGB (AV HDCP)
Quit
RGB
Component
Go to System (1)
Go to System (2)
RGB (Scart)
Quit
Video
Auto
Go to System (3)
Go to System (3)
Go to System (3)
Video
S-video
Quit
Sound
Volume
Mute
Sound
0 - 63
On/Off
Quit
Computer Input
System (1)
Mode 1
Mode 2
SVGA 1
- - - -
Auto PC Adj.
Fine sync.
Total dots
PC Adjust
0 - 31
Horizontal
Vertical
Current mode
H-sync freq.
V-sync freq.
Quit
Clamp
Display area - H
Display area - V
Reset
Yes/No
Mode 1
Mode 2
Mode 3
Mode 4
Mode 5
Quit
Mode free
Store
Mode 1
Mode 2
Mode 3
Mode 4
Mode 5
Quit
Quit
68
Appendix
Video Input
Dynamic
Auto
1080i
1035i
720p
575p
480p
575i
System (2)
Image Select
Standard
Real
Blackboard (Green)
4 Colors
Colorboard
Image 1
Image 2
Image 3
Image 4
480i
Auto
PAL
SECAM
NTSC
System (3)
NTSC 4.43
PAL-M
PAL-N
Contrast
0 - 63
0 - 63
High
Image Adjust
Brightness
Color temp.
Image Select
Dynamic
Standard
Mid
Cinema
Blackboard (Green)
Low
XLow
Adj.
4 Colors
Colorboard
Image 1
Image 2
Image 3
Image 4
Red
0 - 63
0 - 63
0 - 63
0 - 15
0 - 15
Yes/No
Image 1
Image 2
Image 3
Image 4
Quit
Green
Blue
Sharpness
Gamma
Reset
Store
Contrast
Image Adjust
0 - 63
0 - 63
0 - 63
0 - 63
Brightness
Color
Tint
Color temp.
High
Mid
Low
Quit
XLow
Adj.
Red
0 - 63
Green
Normal
True
Screen
0 - 63
0 - 63
0 - 15
Blue
Sharpness
Gamma
Noise reduction
Wide
Full
0 - 15
Off
Scale
Custom
H/V
On/Off
H&V
L1
L2
Off
L1
L2
Position
Common
Reset
Quit
H/V
Yes/No
Yes/No
Progressive
Digital zoom +
Digital zoom –
Film
Yes/No
Reset
Store
Image 1
Image 2
Image 3
Image 4
Quit
Quit
6ꢀ
Appendix
Normal
Wide
Keystone
Blue back
Display
Logo
Screen
Setting
Store/Reset
On/Off
On/Countdown off/Off
Logo select
Off
Scale
Custom
H/V
H&V
On/Off
Default
Position
Common
Reset
Quit
H/V
User
Yes/No
Yes/No
Capture
Yes/No
Logo PIN code lock
Logo PIN code entry
Off
On
Logo PIN code change
Setting
Quit
Quit
English
German
French
Setting
Language
Ceiling
Rear
On/Off
On/Off
Italian
Standby mode
Eco/Normal
Spanish
Portuguese
Dutch
Power management
Off
Ready
Shut down
Swedish
Finnish
Polish
Timer (1-30 Min.)
Quit
On/Off
Hungarian
Romanian
Russian
Chinese
Korean
Japanese
Quit
On start
Closed Caption
Off/CC1/CC2/CC3/CC4
Color/White
Quit
Lamp control
Filter control
Normal/Auto/Eco
Yes/No
Auto setup
Input search
Remote control
Security
Code 1/Code 2
Off
On 1
On 2
Key lock
Off
Projector
Auto PC adj.
Remote Control
Quit
PIN code lock
PIN code lock entry
Off
On
Auto Keystone
Off
On1
Off
On2
PIN code change
Auto
Manual
Quit
Quit
Quit
Fan
L1/L2
Warning log
Lamp counter
Hour(s)
Reset
Quit
Filter counter
Used time/Scrolls remaining
Yes/No
Factory default
Quit
70
Appendix
Indicators and Projector Condition
Check the indicators for the projector condition.
The projector is operating normally
Indicators
WARNING
TEMP
red
LAMP
REPLACE
yellow
WARNING
FILTER
orange
POWER
red/green
Projector Condition
The projector is off. (The AC power cord is unplugged.)
The projector is in stand-by mode. Press the POWER
ON/STAND-BY button to turn on the projector.
The projector is operating normally.
green
The projector is preparing for stand-by or the projection
lamp is being cooling down.
blinking fast
red
The projector cannot be turned on until cooling is completed.
The projector is in the Power management mode.
blinking fast
green
The filter is scrolled using the Filter control function in the
setting menu.
green
When the filter is being scrolled, the Filter replacement
icon and “Please wait...” message (Fig. 1) appear on the
screen for about 30 seconds.
Fig.1 Filter replacement icon and “Please wait...”
The projector is detecting abnormal condition
Indicators
LAMP
REPLACE
yellow
WARNING WARNING
POWER
red/green
Projector Condition
TEMP
FILTER
orange
red
The temperature inside the projector is elevated close to
the abnormally high level.
green
The temperature inside the projector is abnormally high.
The projector cannot be turned on. When the projector
is cooled down enough and the temperature returns to
normal, the POWER indicator lights red and the projector
can be turned on. (The WARNING TEMP. indicator
keeps blinking.) Check and replace the filter.
blinking fast red blinking fast red
• • • red
• • • green / orange / yellow
• • •blinking fast
• • • off
• • • blinking slow
(approx. 2 seconds ON,
2 seconds OFF)
(approx. 0.5 seconds ON, 0.5
seconds OFF)
71
Appendix
Indicators
LAMP
REPLACE
yellow
WARNING WARNING
POWER
red/green
Projector Condition
TEMP.
red
FILTER
orange
The projector has been cooled down enough and the
temperature returns to normal. When turning on the
projector, the WARNING TEMP. indicator stops blinking.
Check and replace the filter.
red
The lamp has been used overtime. Replace the lamp
immediately and then reset the lamp counter. The
indicator will be turned off after resetting the counter.
Any
yellow
If the Filter counter reached a time set in the timer setting,
a Filter replacement icon (Fig.2) appears on the screen
and the WARNING FILTER indicator on the top control
lights up. Replace the filter as soon as possible. If the
filter is out of scroll and the projector reaches a time set
in the timer setting, Fig. 3 appears on the screen and the
WARNING FILTER indicator lights up. Replace the filter
cartridge as soon as possible.If the filter is clogged and
no scroll is left in the filter cartridge,
Any
orange
Fig.2 Filter replacement icon
a Filter cartridge replacement icon (Fig.4) appears on the
screen and the WARNING FILTER indicator lights up.
Replace the filter cartridge as soon as possible.
Note:
Fig.3
Fig.2, Fig.3 and Fig.4 icon will not appear when the
Display function is set to “Off” (p.47), during “Freeze”
(p.23), or “No show” (p.24).
Fig.4 Filter cartridge replacement icon
The filter cartridge is not installed in the projector. Check
the filter compartment to see if the filter cartridge is
installed in the projector. When the filter cartridge is
installed and the indicators continue to light and blink,
read the column below.
blinking fast
orange
blinking fast
yellow
The projector detects an abnormal condition and cannot
be turned on. Unplug the AC power cord and plug it again
to turn on the projector. If the projector is turned off again,
unplug the AC power cord and contact the dealer or
the service center. Do not leave the projector on. It may
cause an electric shock or a fire hazard.
When the filter detects clogging, reaches a time set in the timer setting or runs out of the filter scroll, the WARNING
FILTER indicator lights orange. When this indicator lights orange, replace the filter or the filter cartridge with a new
one promptly. Reset the Filter counter and Scroll counter after replacing the filter cartridge (p.59).
When the projection lamp reaches its end of life, the LAMP REPLACE indicator lights yellow. When this indicator
lights yellow, replace the projection lamp with a new one promptly. Reset the lamp counter after replacing the lamp
(p.62).
72
Appendix
Compatible Computer Specifications
Basically this projector can accept the signal from all computers with the V, H-Frequency below mentioned
and less than 140 MHz of Dot Clock for Analog signal and 110 MHz of Dot Clock for digital signal.
When selecting these modes, PC adjustment can be limited.
ON-SCREEN
DISPLAy
H-Freq
(kHz)
V-Freq
(Hz)
ON-SCREEN
DISPLAy
H-Freq
(kHz)
V-Freq
(Hz)
RESOLUTION
RESOLUTION
VGA 1
VGA 2
640 x 480
720 x 400
640 x 400
640 x 480
640 x 480
640 x 480
640 x 480
640 x 480
640 x 480
––––––––
––––––––
800 x 600
800 x 600
800 x 600
800 x 600
800 x 600
800 x 600
800 x 600
800 x 600
800 x 600
800 x 600
800 x 600
832 x 624
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
31.47
31.47
31.47
37.86
37.86
37.50
43.269
34.97
35.00
15.734
15.625
35.156
37.88
46.875
53.674
48.08
37.90
34.50
38.00
38.60
32.70
38.00
49.72
48.36
68.677
60.023
56.476
60.31
48.50
44.00
63.48
36.00
62.04
61.00
35.522
46.90
47.00
58.03
60.24
59.88
70.09
70.09
74.38
72.81
75.00
85.00
66.60
66.67
SXGA 1
SXGA 2
SXGA 3
SXGA 4
SXGA 5
SXGA 6
SXGA 7
SXGA 8
SXGA 9
SXGA 10
SXGA 11
SXGA 12
SXGA 13
SXGA 14
SXGA 15
SXGA 16
SXGA 17
SXGA 18
SXGA 19
SXGA 20
SXGA +1
SXGA +2
SXGA +3
MAC21
MAC
1152 x 864
1280 x 1024
1280 x 1024
1280 x 1024
1280 x 1024
1280 x 1024
1280 x 1024
1280 x 1024
1280 x 1024
1280 x 960
1152 x 900
1152 x 900
1280 x 1024
1280 x 1024
1280 x 1024
1280 x 1024
1152 x 900
1280 x 1024
1280 x 1024
1280 x 1024
1400 x 1050
1400 x 1050
1400 x 1050
1152 x 870
1280 x 960
1280 x 1024
––––––––
64.20
62.50
63.90
63.34
63.74
71.69
81.13
63.98
79.976
60.00
61.20
71.40
50.00
50.00
63.37
76.97
61.85
46.43
63.79
91.146
63.979
65.346
65.121
68.68
75.00
80.00
31.47
31.25
37.50
45.00
33.75
33.75
28.125
48.36
47.70
48.36
56.16
47.776
60.289
68.633
75.00
81.25
87.5
70.40
58.60
60.00
59.98
60.01
67.19
76.107
60.02
75.025
60.00
65.20
75.60
VGA 3
VGA 4
VGA 5
VGA 6
VGA 7
MAC LC13
MAC 13
480i
60.00
(Interlace)
50.00
(Interlace)
575i
SVGA 1
SVGA 2
SVGA 3
SVGA 4
SVGA 5
SVGA 6
SVGA 7
SVGA 8
SVGA 9
SVGA 10
SVGA 11
MAC 16
XGA 1
56.25
60.32
75.00
85.06
72.19
61.03
55.38
60.51
60.31
51.09
60.51
74.55
60.00
84.997
75.03
70.07
74.92
60.02
54.58
79.35
86.00
(Interlace)
94.00
(Interlace)
60.01
72.00
66.00
86.70
(Interlace)
60.18
85.024
60.190
60.116
59.902
75.06
75.08
75.08
59.88
50.00
50.00
60.00
XGA 2
XGA 3
MAC
XGA 4
480p
XGA 5
575p
––––––––
XGA 6
720p
720p
––––––––
––––––––
XGA 7
60.00
(Interlace)
1035i
––––––––
XGA 8
60.00
(Interlace)
87.17
(Interlace)
1080i
––––––––
XGA 9
50.00
(Interlace)
1080i
––––––––
XGA 10
XGA 11
XGA 12
XGA 13
XGA 14
XGA 15
MAC 19
77.07
75.70
86.96
(Interlace)
WXGA 1
WXGA 2
WXGA 3
WXGA 4
WXGA 6
WXGA 7
WXGA 8
UXGA 1
UXGA 2
UXGA 3
UXGA 4
1366 x 768
1360 x 768
1376 x 768
1360 x 768
1280 x 768
1280 x 768
1280 x 768
1600 x 1200
1600 x 1200
1600 x 1200
1600 x 1200
60.00
60.00
60.00
72.00
59.87
74.893
84.837
60.00
65.00
70.00
75.00
58.20
58.30
72.00
75.08
93.75
73
Appendix
When the input signal is digital from DVI terminal, refer to the chart below.
ON-SCREEN
DISPLAy
H-Freq
(KHz)
V-Freq
(Hz)
ON-SCREEN
DISPLAy
H-Freq
(KHz)
V-Freq
(Hz)
RESOLUTION
RESOLUTION
D-VGA
D-480p
640 x 480
640 x 480
768 x 575
800 x 600
1024 x 768
1366 x 768
1360 x 768
1376 x 768
1360 x 768
1366 x 768
1280 x 768
1280 x 768
31.47
59.94
59.88
50.00
60.32
60.00
60.00
60.00
60.00
72.000
50.000
59.870
74.893
D-SXGA1
D-SXGA2
D-SXGA3
D-SXGA+1
D-720p
1280 x 1024
1280 x 1024
1280 x 1024
1400 x 1050
1280 x 720
1280 x 720
1920 x 1035
1920 x 1080
1920 x 1080
63.98
60.276
31.65
63.97
37.50
45.00
33.75
33.75
28.125
60.02
58.069
29.80
60.19
50.00
60.00
31.47
D-575p
31.25
D-SVGA
37.879
43.363
48.36
D-XGA
D-WXGA 1
D-WXGA 2
D-WXGA 3
D-WXGA 4
D-WXGA 5
D-WXGA 6
D-WXGA 7
D-720p
60.00
47.70
D-1035i
(Interlace)
60.00
48.36
D-1080i
(Interlace)
50.00
56.160
46.500
47.776
60.289
D-1080i
(Interlace)
Notes:
• When the input signal is D-SXGA 1, D-SXGA 2, D-SXGA 3, or D-SXGA+1, images may not be
displayed properly depending on computers.
• The specifications are subject to change without notice.
74
Appendix
Technical Specifications
Mechanical Information
Projector Type
Multi-media Projector
Dimensions (W x H x D)
Net Weight
410.0 mm x 85.0 mm x 262.8 mm (Not including protrusions)
8.82lbs (4.0 kg)
Foot Adjustment
0˚ to 10.0˚
Panel Resolution
LCD Panel System
Panel Resolution
Number of Pixels
0.63" TFT Active Matrix type, 3 panels
1,024 x 768 dots
2,359,296 (1,024 x 768 x 3 panels)
Signal Compatibility
Color System
High Definition TV Signal
Scanning Frequency
PAL, SECAM, NTSC, NTSC4.43, PAL-M, and PAL-N
480i, 480p, 575i, 575p, 720p, 1035i, and 1080i
H-sync. 15 ~ 100 KHz, V-sync. 50 ~ 100 Hz
Optical Information
Projection Image Size (Diagonal)
Projection Lens
Adjustable from 40" to 300"
F 1.60-1.76 lens with f =22.33 mm ~ 26.80 mm with manual zoom and focus
Throw Distance
Projection Lamp
4.6' ~ 41.8' (1.4 m ~ 12.7 m)
220W
Interface
Video Input Jack
RCA Type x 1
S-video Input Jack
Audio Input Jacks
Computer Input 1/DVI-I
Computer Input 2/Component Input
Monitor Output
Mini DIN 4 pin x 1
RCA Type x 2
Digital/Analog RGB (DVI-I ) Terminal x 1
Analog RGB (Mini D-sub 15 pin) Terminal x 1
Analog RGB (Mini D-sub 15 pin) Terminal x 1
Computer2/ Component Audio Input Jack
Mini Jack (stereo) x 1
Computer1 Audio Input Jack
Control Input
Mini Jack (stereo) x 1
Mini D-sub 9 pin x 1
Audio Output Jack
Mini Jack (stereo) x 1 (Variable)
Audio
Internal Audio Amp
Built-in Speaker
7.0 W RMS
1 speaker, ø1.46" (37mm)
Power
Voltage and Power Consumption
AC 100 ~ 120 V (3.4A Max. Ampere), 50/60 Hz (The U.S.A and Canada)
AC 200 ~ 240 V (1.7A Max. Ampere), 50/60 Hz (Continental Europe and The U.K.)
Operating Environment
Operating Temperature
Storage Temperature
41˚F ~ 95˚F (5˚C ~ 35˚C)
14˚F ~ 140˚F (-10˚C ~ 60˚C)
Remote Control
Battery
Operating Range
Dimensions
Net Weight
AA or LR6 1.5 V ALKALINE TYPE x 2
16.4' (5 m)/±30˚
1.9" (W) x 0.87" (H) x 5.7" (D) (49 mm x 22 mm x 145.3 mm)
3.53 oz (100 g) (including batteries)
75
Appendix
Accessories
Owner's Manual (CD-ROM)
Quick Reference Guide
AC Power Cord
Remote Control and Batteries
VGA Cable
PIN Code Label
●
●
The specifications are subject to change without notice.
LCD panels are manufactured to the highest possible standards. Even though 99.99% of the pixels
are effective, a tiny fraction of the pixels (0.01% or less) may be ineffective by the characteristics of the
LCD panels.
Optional Parts
The parts listed below are optionally available. When ordering those parts, specify the item and Model
No. to the sales dealer.
Model No
COMPONENT-VGA Cable
SCART-VGA Cable
: AH-98771
: AH-98881
76
Appendix
Configurations of Terminals
COMPUTER INPUT/COMPONENT INPUT/MONITOR OUTPUT TERMINAL (ANALOG)
DVI-I (DIGITAL/ANALOG)
C1 C2
Analog Red Input
C1
C2
C3
C4
C5
Analog Green Input
Analog Blue Input
Analog Horiz. sync
Analog Ground (R/G/B)
1
9
2
3
4
5
6
7
8
10 11 12 13 14 15 16
17 18 19 20 21 22 23 24
C3 C4
C5
T.M.D.S. Data2–
T.M.D.S. Data2+
T.M.D.S. Data2 Shield
No Connect
T.M.D.S. Data1–
T.M.D.S. Data1+
T.M.D.S. Data1 Shield
No Connect
T.M.D.S. Data0–
1
2
3
4
5
6
7
8
ꢀ
17
18
1ꢀ
20
21
22
23
24
T.M.D.S. Data0+
T.M.D.S. Data0 Shield
No Connect
10
11
12
13
14
15
16
No Connect
No Connect
No Connect
DDC Clock
+5V Power
T.M.D.S. Clock Shield
T.M.D.S. Clock+
T.M.D.S. Clock–
DDC Data
Ground (for +5V)
Hot Plug Detect
Analog Vert. sync
Terminal : Analog RGB (Mini D-sub 15 pin)
1
2
3
4
5
6
7
8
Red (R/Cr) Input/R Output
Green (G/Y) Input/G Output
Blue (B/Cb/---) Input/B Output 11 Ground
9
5V / ---
5
4
3
2
1
10
9
8
7
6
10 Ground (Vert.sync.)
15
12
11
14
13
-----
Ground (Horiz.sync.)
Ground (Red)
12 DDC data / ---
Horiz. sync. Input/Output (Composite H/V sync.Input)
13
14 Vert. sync. Input/Output
15 DDC clock / ---
Ground (Green)
Ground (Blue)
CONTROL PORT CONNECTOR (D-sub ꢀ pin)
Serial
1
2
3
4
5
6
7
8
9
-----
R X D
T X D
-----
SG
-----
RTS
CTS
-----
77
Appendix
PIN Code Number Memo
Write down the PIN code number in the column below and keep it with this manual securely. If you forgot
or lost the number and unable to operate the projector, contact the service station.
PIN Code Lock No
Factory default set No: 1 2 3 4*
Logo PIN Code Lock No
Factory default set No: 4 3 2 1*
* Should the four-digit number be
changed, the factory set number
will be invalid.
While the projector is locked with the PIN code....
Put the label below (supplied) on in a prominent place of
the projector's body while it is locked with a PIN code.
7ꢀ
U.S.A.
Canada
EIKI International, Inc.
30251 Esperanza
Rancho Santa Margarita
CA 92688-2132
U.S.A.
Tel : 800-242-3454 (949)-457-0200
Fax : 800-457-3454 (949)-457-7878
E-Mail : [email protected]
EIKI CANADA - Eiki International, Inc.
P.O. Box 156, 310 First St. - Unit 2,
Midland, ON, L4R 4K8, Canada
Tel : 800-563-3454 (705)-527-4084
Fax : 800-567-4069 (705)-527-4087
E-Mail : [email protected]
Deutschland & Österreich
Eastern Europe
EIKI Deutschland GmbH
Am Frauwald 12
EIKI CZECH spol. s.r.o.
Um lecká 15
65510 Idstein
170 00 Praha 7
Deutschland
Czech Republic
Tel : 06126-9371-0
Fax : 06126-9371-14
E-Mail : [email protected]
Tel : +42 02 20570024
+42 02 20571413
Fax : +42 02 20571411
E-Mail : [email protected]
China
South East Asia
EIKI (Shanghai) Co., Ltd.
1. Dapu Road,
Golden Magnolia Plaza
#2109 Shanghai,
EIKI Industrial (M) Sdn Bhd
No. 3A-2C, 4th Floor, Jalan PJU 8/3A,
Perdana Business Centre,
Bandar Damansara Perdana,
47820 Petaling Jaya, Selangor
Malaysia
Tel : +603-7722-4362
Fax : +603-7722-4392
E-Mail : [email protected]
200023 China
Tel : 86-21-5396-0088
Fax : 86-21-5396-0318
E-mail : [email protected]
Japan & Worldwide
EIKI Industrial Company Limited.
4-12 Banzai-Cho, Kita-Ku, Osaka,
530-0028 Japan
Tel :
Fax :
+81-6-6311-9479
+81-6-6311-8486
©2008 Eiki International, Inc.
KK7BC
|