|
CD-WRITER
5232IM
CD-ReWritable Drive
User’s Manual
FCC Compliance Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
1. this device may not cause harmful interference, and
2. this device must accept any interference received, including interference that
may cause undesired operation.
FCC Warning Statement
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can emit radio frequency energy
and, if not installed or used in accordance with the instructions, may cause
interference to radio communications. However, television reception interference
can be determined by turning the equipment off and on. The user is encouraged to
correct the interference by one or more of the following measures:
•
•
•
Reorient or relocate the receiving antenna
Increase the separation between the equipment and the receiver
Connect the equipment into an outlet different from that to which the receiver
is connected
•
Consult the dealer or an experienced radio/TV technician for help.
CAUTION
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
FOR EUROPE
“The drive is in conformity with the EMC directive and low-voltage
directive.”
Table of Contents
INTRODUCTION
1
SYSTEM REQUIREMENTS
PACKAGE CONTENTS
2
2
INSTALLATION
3
HOST INTERFACE CONNECTIONS
HARDWARE INSTALLATION
DRIVER INSTALLATION
Windows Environment
SOFTWARE INSTALLATION
Windows Environment
3
4
6
6
6
6
CONNECTION & OPERATION
7
FRONT PANEL
REAR VIEW
7
8
TECHNICAL DATA
9
TROUBLESHOOTING
12
CD-WRITER 5232IM
INTRODUCTION
CD-WRITER 5232IM is a half-height CD-ReWritable drive of standard
IDE interface. It supports maximum 52X speed writing ability on CD-R
discs, 32X speed on CD-RW discs and 52X speed reading performance.
The drive backs up all writing modes and different CD formats and it
automatically recognizes the media placed in the drive, whether a CD, a
CD-R or a CD-RW. With the bundled CD-RW mastering software, CD-
WRITER 5232IM is an ideal model for creating customized audio and
data CDs, and for archiving or distributing big files to achieve data
interchange and backup.
Here are some important features of CD-WRITER 5232IM:
♦ 8X, 16X, 24X, 32X, 40X, 48X and 52X writing speed on CD-R
media
♦ 4X, 10X, 12X, 16X, 24X and 32X writing speed on CD-RW media
♦ Adopts Buffer Underrun Prevention technology (MTKSuperLink)
♦ Supports MultiRead function
♦ Supports writing modes of TAO, DAO, SAO and packet writing
♦ Large internal buffer: 2MB
♦ Advanced dust-sealed design
♦ Low power consumption
♦ Firmware upgrade possibility via Flash Memory
1
CD-WRITER 5232IM
System Requirements
For IBM compatible PCs, the system requirements recommended
are as follows:
♦ PC sufficient to run Windows 98/ME/2000/XP
♦ Pentium II 350MHz above with at least 64MB of memory
♦ Fast and sufficient hard disk space (minimum 200MB for
installation, 1GB or more is recommended.)
♦ IDE host interface supporting ATAPI MMC command
♦ Operating system: Microsoft Windows 98/ME/2000/XP
Package Contents
♦ CD-WRITER 5232IM
♦ Audio cable
♦ Application software disc
2
CD-WRITER 5232IM
INSTALLATION
Host Interface Connections
Most current mainboard models have two IDE ports (primary and
secondary) which can connect two IDE cables. Two IDE cables
allow you to connect up to four devices, but it is recommended that
you separate IDE ports for your hard drive and your CD-ReWritable
drive. This will ensure that your hard drive’s performance and speed
won’t be affected by having the CD-RW drive on the same cable.
If you connect only one device on the cable, you can set the jumper
as “master” or “slave”.
If you connect two devices (e.g. CD-ROM & CD-RW) on the same
cable, set different jumpers for each device (CD-ROM as “master”,
CD-RW as “slave” and vice versa.) The same rule applies to the
connection of having your hard disk and one other device on the
same cable.
CSEL
MASTER
SLAVE
JUMPER
3
CD-WRITER 5232IM
You may consider one of the two ways recommended below to
connect your drive.
♦
♦
To get the most stable performance for the CD-RW drive to write:
Primary IDE Master: Hard Disk
Primary IDE Slave: CD-ROM Drive
Secondary IDE Master: CD-RW drive
For best hard disk performance:
Primary IDE Master: Hard Disk
Secondary IDE Master: CD-ROM drive
Secondary IDE Salve: CD-RW drive
Hardware Installation
1. Turn off the power to the computer system and all peripheral
devices.
2. Disconnect all cables from the back of your computer, and then
remove the cover from the computer.
3. Insert the CD-ReWritable drive into one of the vacant 5.25" drive
bays and secure it with screws to your PC.
ꢀ In order to prevent interference between the CD-ReWritable drive and the
computer, please make sure to mount the drive using all four mounting
screws.
4. Connect the 40-pin IDE cable from one of the IDE ports on the
mainboard to the 40-pin connector of your CD-ReWritable drive.
Also, connect the power supply cable to the back of the CD-
ReWritable drive.
4
CD-WRITER 5232IM
ꢀ The red-edge of the IDE Cable must be connected to Pin 1 on the CD-
ReWritable drive.
5. If you have a sound card that can be connected to this CD-
ReWritable drive, you can connect the drive (as Audio-out) and the
sound card (as Audio-in) with a 4-pin audio cable. (See figure above.)
If your mainboad is integrated with built-in sound system, plug the 4-
pin audio cable into the CD-IN connector on the mainboard as
Audio-in.
6. Re-attach the cover of your computer, and reconnect all power cords.
5
CD-WRITER 5232IM
Driver Installation
Windows Environment
CD-WRITER 5232IM is a PnP device, and Windows 98/ME/2000/XP
can automatically detect the drive and load the appropriate driver.
If Windows cannot detect the drive, you can operate manually:
1.
Click the Control Panel Icon in My Computer and then click
Add New Hardware. The Add New Hardware window appears.
2.
The program will automatically search for your new drive and
load the appropriate driver.
Software Installation
The bundled mastering software gives you the complete solution for
making audio/data CDs right from your desktop. It allows you to copy
files from your computer to a recordable compact disc. In addition,
the audio CDs you create can be played in your home or car CD
player. For the CD-RW media, you can write and erase data on the
CD as you do with a floppy disk.
Windows Environment
(1) Run install.exe or setup.exe
or
(2) Refer to the manual in the software disc.
6
CD-WRITER 5232IM
CONNECTION & OPERATION
Front Panel
1
2
3
4
1. LED Indicator
Flashes “green” while verifying or reading a disc/ writing a CD-
R/CD-RW disc.
2. Disc Tray
This is the tray for the disc. Place the disc in the tray, then press
the Close/Eject button or lightly push the tray to close it.
3. Emergency Eject Hole
When the Close/Eject button can’t work properly and the disc tray
can’t be opened, you can insert a paper clip or a small rod into
this hole for manual ejection. Please make sure to power off the
system before you do that.
4. Close/Eject button
This button opens and closes the disc tray. If the tray is closed,
pressing the button will eject it. If the drive is playing, pressing
this button will stop it.
7
CD-WRITER 5232IM
NOTE: The front panel is subject to change without notice.
Rear View
1. Digital Audio Output Connector
If your sound card has a digital audio IEC958 format connector, you
can connect it to this digital audio output connector with a 2-pin
audio cable.
2. Analog Audio Output Connector
This connector allows you to connect the drive to your sound card
with a 4-pin audio cable.
3. Device Configuration Jumper
Set the jumper to Master, Slave or Cable Select according to your
system configuration.
4. IDE Interface Connector
Plug one end of the 40-pin IDE cable here to join the 40-pin IDE
connector on the motherboard. The red-edge of the IDE cable must
be connected to Pin 1 of each connector.
5. Power Supply Connector
By plugging the computer’s power supply cable here, you can
connect the CD-RW drive and your computer system.
8
CD-WRITER 5232IM
TECHNICAL DATA
Performance
Transfer rate
Read:
CD-ROM/CD-R:
7800kb/s (up to 52X)
CD-RW: 6000kb/s (up to 40X)
Write:
CD-R 7800kb/s (up to 52X)
CD-RW 4800kb/s (up to 32X)
Access time
100ms at ⅓ stroke(52X CD-ROM)
180ms at full stroke(52X CD-ROM)
120ms at ⅓ stroke (52X CD-RW)
200ms at full stroke (32X CD-RW)
Data buffer
2MB
CD format support
CD-Audio, CD-EXTRA, CD-ROM,
CD-ROM XA, CD-I, Video CD,
Photo CD, CD-Text
Writing modes
Writing speed
TAO (Track at once), DAO (Disc
At Once), SAO (Session at once),
Multi-session, Incremental Packet
Writing (fixed and variable packet
size)
CD-R:
8X/16X/24X/32X/40X/48X/52X
CD-RW:
4X/10X/12X/16X/24X/32X
Specification
Interface
IDE
9
CD-WRITER 5232IM
Form factor
Disc loading
5.25" Half Height
Tray (motorised)
Audio output level
Line out = 0.6 ± 10%Vrms
Headphone out = 0.6± 10%Vrms
Power
5 VDC & 12VDC
Dimensions
Height
41.8 ± 0.2 mm
148.6 ± 0.3 mm
177.0 ± 0.3mm
Width
Depth
Weight
1 kg
Disc Specification
Capacity
120mm disc: 74min
650MBytes
700MBytes
800MBytes
Mode-1
Mode-1
Mode-1
80min
90min
80mm disc:
18min
21min
158Mbytes
184MBytes
Mode-1
Mode-1
Disc Type
CD-Recordable media (Orange
Book Part II), CD-ReWritable
media (Orange Book Part III)
10
CD-WRITER 5232IM
Environment
Temperature
Operating
5°C to 45°C
Non-operating
-20°C to 60°C
Humidity
Operating
Non-operating
8% ~ 80%RH
5% ~ 95%RH
11
CD-WRITER 5232IM
TROUBLESHOOTING
To help you get more familiar with CD-WRITER 5232IM, the following FAQ
lists some common problems you might encounter. Please read it for
reference before you request RMA support from your dealer.
Q1. CD-WRITER 5232IM cannot be recognized.
(1) The drive might not be connected properly. Please check whether the
IDE cable and power connector are tightly connected.
(2) Check if there is jumper conflict. Normally, if 2 drives connected with
one IDE cable, the jumper has to separate one to MASTER & the other
to SLAVE.
(3) If Windows can’t detect CD-WRITER 5232IM, click on the “Add New
Hardware” in the Control Panel. Windows will start detecting.
Q2. CD-WRITER 5232IM doesn’t have power.
Please check if the power cord is connected securely.
Q3. The CD-RW drive cannot read some general discs.
Please check if the disc has deep scratches, fingerprints, or other
contaminants on the discs surface. Clean the disc if it’s necessary.
Q4. There is noise while reading.
If the disc used is eccentric or there are labels stuck on the disc surface, it
will cause noise.
Q5. The drive can’t read former session(s) of the CD-R disc which has
been written twice or more times.
Before writing CD-R discs with data copy, remember to choose “Import
session” so as to read the former sessions.
Q6. The external speaker doesn’t have sound when playing music CD.
12
CD-WRITER 5232IM
(1) Please check if the audio cable is connected to the audio connector
properly.
(2) Check both rear side of the CD-RW drive and sound card on M/B (If
Audio chipset is on board). If they are well connected, check if the
sound card is working.
Q7. The tray cannot be ejected.
There are two possible reasons:
(1) Need to be ejected by the application.
Some of the burning or playing application will lock the drive. You have
to eject by application and close it so as to restore the use of panel
buttons.
(2) The CD is inserted incorrectly.
Please insert a paper clip or small rod into the emergency hole on the
front panel for manual ejection.
Q8. CD-WRITER 5232IM drive cannot write.
We suggest as follows:
(1) Use the burning software which is provided by original supplier and
bundled with this CD-ReWritable drive or download the update file from
internet.
(2) More capacity of hard disk is needed if using hard disk as temporary
buffer.
(3) Place the disc correctly.
(4) The blank disc needs full format first if using packet writing software.
Q9. “Buffer underrun” always occurs while writing discs.
Here are some suggestions:
(1) Close the screen saver & TSR (Terminate and Stay Resident).
(2) Quit other redundant application when burning.
(3) Select good quality and high-speed supported blank discs.
13
CD-WRITER 5232IM
(4) Increase main memory capacity.
(5) Select other burning software.
(6) De-fragment the hard disk.
(7) Keep the source & destination discs clean. (no scratches, fingerprints or
contamination.)
(8) Copy data as image file to hard drive to avoid buffer underrun.
(9) Keep the system clean. Do not install redundant driver or application to
reduce system loading as well as confliction.
(10) Enable Buffer Underrun Protection mode if your software supports it.
Q10. Does this CD-RW drive support over-burning?
Yes, but please use burning software which supports this function.
Q11. What burning software supports this CD-RW drive?
Software such as Adaptec EasyCD Creator, Ahead Nero-Burning ROM,
NTI CDMaker…etc.
Q12. Does CD-WRITER 5232IM support CD-Text & SAO (Session At
Once) function?
Yes, it does support CD-Text & SAO function and you may edit the title or
content into your music CD.
14
3100552360
Version 1.0
March 2004
|