Durabrand DBTV2500 User Manual

DBTV2500  
SERVICE MANUAL  
COLOR TELEVISION RECEIVER  
ORIGINAL  
MFR’S VERSION B  
Design and specifications are subject to change without notice.  
Change of IC101  
DIFFERENCES  
MFR'S VERSION B  
DESCRIPTION  
MFR'S VERSION D  
DESCRIPTION  
PART NO.  
PART NO.  
I56F07045A IC  
A3I058G01B MAIN PCB ASS'Y  
REF. NO.  
IC101  
I56F07044A IC  
OEC7044A  
TMX456A  
OEC7045A  
TMX456A  
PCB010 A3I058G01A MAIN PCB ASS'Y  
SPEC.NO. M3I0-62G  
O/R NO. A073521  
SERVICING NOTICES ON CHECKING  
1. KEEP THE NOTICES  
6. AVOID AN X-RAY  
As for the places which need special attentions,  
they are indicated with the labels or seals on the  
cabinet, chassis and parts. Make sure to keep the  
indications and notices in the operation manual.  
Safety is secured against an X-ray by consider-  
ing about the cathode-ray tube and the high  
voltage peripheral circuit, etc.  
Therefore, when repairing the high voltage pe-  
ripheral circuit, use the designated parts and  
make sure not modify the circuit.  
Repairing except indicates causes rising of high  
voltage, and it emits an X-ray from the cathode-  
ray tube.  
2. AVOID AN ELECTRIC SHOCK  
There is a high voltage part inside. Avoid an  
electric shock while the electric current is  
flowing.  
3. USE THE DESIGNATED PARTS  
The parts in this equipment have the specific  
characters of incombustibility and withstand  
voltage for safety. Therefore, the part which is  
replaced should be used the part which has  
the same character.  
7. PERFORM A SAFETY CHECK AFTER  
SERVICING  
Confirm that the screws, parts and wiring which  
were removed in order to service are put in the  
original positions, or whether there are the  
portions which are deteriorated around the  
serviced places serviced or not. Check the  
insulation between the antenna terminal or  
external metal and the AC cord plug blades.  
And be sure the safety of that.  
Especially as to the important parts for safety  
which is indicated in the circuit diagram or the  
table of parts as a  
mark, the designated  
parts must be used.  
4. PUT PARTS AND WIRES IN THE  
ORIGINAL POSITION AFTER  
ASSEMBLING OR WIRING  
(INSULATION CHECK PROCEDURE)  
1. Unplug the plug from the AC outlet.  
2. Remove the antenna terminal on TV and turn  
on the TV.  
3. Insulation resistance between the cord plug  
terminals and the eternal exposure metal  
[Note 2] should be more than 1M ohm by  
using the 500V insulation resistance meter  
[Note1] .  
There are parts which use the insulation  
material such as a tube or tape for safety, or  
which are assembled in the condition that  
these do not contact with the printed board.  
The inside wiring is designed not to get closer  
to the pyrogenic parts and high voltage parts.  
Therefore, put these parts in the original  
positions.  
4. If the insulation resistance is less than 1M  
ohm, the inspection repair should be  
required.  
5. TAKE CARE TO DEAL WITH THE  
CATHODE-RAY TUBE  
[Note 1]  
In the condition that an explosion-proof cathode-  
ray tube is set in this equipment, safety is  
secured against implosion. However, when  
removing it or serving from backward, it is  
dangerous to give a shock. Take enough care to  
deal with it.  
If you have not the 500V insulation  
resistance meter, use a Tester.  
[Note 2]  
External exposure metal: Antenna terminal  
HOW TO ORDER PARTS  
Please include the following informations when you order parts. (Particularly the VERSION LETTER.)  
1. MODEL NUMBER and VERSION LETTER  
The MODEL NUMBER can be found on the back of each product and the VERSION LETTER can be  
found at the end of the SERIAL NUMBER.  
2. PART NO. and DESCRIPTION  
You can find it in your SERVICE MANUAL.  
IMPORTANT  
Inferior silicon grease can damage IC's and transistors.  
When replacing an IC's or transistors, use only specified silicon grease (YG6260M).  
Remove all old silicon before applying new silicon.  
A1-1  
CONTENTS  
A1-1  
A1-1  
A1-1  
A2-1  
A3-1~A3-4  
B-1, B-2  
C-1  
C-1  
C-1  
SERVICING NOTICES ON CHECKING......................................................................................................  
HOW TO ORDER PARTS ...........................................................................................................................  
IMPORTANT................................................................................................................................................  
CONTENTS .................................................................................................................................................  
GENERAL SPECIFICATIONS ....................................................................................................................  
DISASSEMBLY INSTRUCTIONS ...............................................................................................................  
SERVICE MODE LIST.................................................................................................................................  
CONFIRMATION OF USING HOURS .........................................................................................................  
NOTE FOR THE REPLACING OF MEMORY IC ........................................................................................  
ELECTRICAL ADJUSTMENTS ..................................................................................................................  
MAJOR COMPONENTS LOCATION GUIDE .............................................................................................  
BLOCK DIAGRAM ......................................................................................................................................  
PRINTED CIRCUIT BOARDS  
D1-1~D2-1  
D3-1  
E-1, E-2  
F-1~F-4  
MAIN/CRT...........................................................................................................................................  
SCHEMATIC DIAGRAMS  
G-1, G-2  
G-3, G-4  
G-5, G-6  
G-7, G-8  
G-9, G-10  
H-1, H-2  
I-1  
MICON/TUNER..................................................................................................................................  
CHROMA ...........................................................................................................................................  
DEFLECTION/CRT ............................................................................................................................  
POWER .............................................................................................................................................  
SOUND ..............................................................................................................................................  
WAVEFORMS .............................................................................................................................................  
MECHANICAL EXPLODED VIEW ..............................................................................................................  
MECHANICAL REPLACEMENT PARTS LIST ..........................................................................................  
ELECTRICAL REPLACEMENT PARTS LIST ............................................................................................  
J1-1  
J2-1, J2-2  
A2-1  
GENERAL SPECIFICATIONS  
G-1.Outline of the Product  
25 inch( 626 mmV):Measured diagonally  
Color CRT  
100 degree deflection  
G-2.Broadcasting System  
US  
System  
NTSC  
M
G-3.Color System  
PAL  
SECAM or Monochrome signal  
G-4.NTSC Playback(PAL 60Hz)  
G-5.NTSC 3.58+4.43/PAL60Hz  
G-6.Antenna Input Impedance  
Yes  
Yes  
No  
No  
VHF/UHF 75 ohm unbalanced  
G-7.Tuner and Receiving  
Contactless Electric tuner  
1Tuner System  
2Tuner System  
channel Tuner  
Oscar(W/O HYPER)  
France CATV)  
Oscar(W/ HYPER)  
Others  
Receiving channel  
(USA)  
2-69 ,  
4A  
,
A-5~A-1 , A~I , J~W , W+1~W+84  
Tuning System  
Frequency syn.  
Voltage syn.  
Others  
G-8.Preset Channel  
-- channels  
G-9.Intermediate Frequency  
Picture(fP)  
45.75 MHz  
41.25 MHz  
4.50 MHz  
MHz  
MHz  
MHz  
MHz  
MHz  
MHz  
Sound (fS)  
fP-fS  
G-10.Stereo/Dual TV Sound  
Yes( NICAM  
GERMAN  
Yes  
USA  
JAPAN)  
No  
G-11.Tuner Sound Muting  
G-12.Power Source  
No  
120  
V
AC 50Hz  
AC 60Hz  
G-13.Power Consumption:  
115 W at AC  
W at DC  
120  
120  
V
V
V
60 Hz  
60 Hz  
Stand by:  
Per Year:  
8
-
W at AC  
kWh / Year  
G-14.Dimensions(Approx.)  
618 mm(W)  
504 mm(D)  
525 mm(H)  
G-15.Weight(Approx.)  
Net  
Gross:  
:
27  
29  
kg ( 59.9 lbs)  
kg ( 64.3 lbs)  
G-16.Cabinet Material  
Cabinet Front:  
PS  
ABS  
94HB  
94V2  
94V0  
DECABROM  
NON-DECA  
Back Panel:  
PS  
ABS  
94HB  
94V2  
94V0  
DECABROM  
NON-DECA  
A3-1  
GENERAL SPECIFICATIONS  
Power Fuse  
G-17.Protector:  
G-18.Regulation  
Safety  
UL  
CSA  
NF  
SAA  
SI  
CE  
SEV  
BS  
SEMKO  
NOM  
NEMKO  
HOMOLO  
DENTORI  
FEMKO  
SABS  
UNE  
DEMKO  
CNS  
IEC65  
SISIR  
NONE  
NZ  
AS3159  
GOST  
Radiation  
FCC  
DOC  
FTZ  
PTT  
CE  
HOMOLO  
NONE  
SEV  
UNE  
SABA  
CNS  
SI  
NF  
NZ  
CISPR13  
DENTORI  
AS/NZS  
X-Radiation  
PTB  
DHHS  
HWC  
DENTORI  
NONE  
G-19.Temperature  
Operation  
Storage  
5
-20  
˚C~ 40 ˚C  
˚C~ 60 ˚C  
G-20.Operating Humidity  
Less than  
80  
%RH  
G-21.Clock and Timer  
Sleep Timer  
Yes Max 120  
Yes  
Yes  
Min.( 10 Min. Step)  
Programs  
Programs  
No  
No  
No  
On/Off Timer  
Wake Up Timer  
G-22.Timer back up Time  
More than  
-- Minutes (at Power Off Mode)  
Din Type  
G-23.Terminals  
VHF/UHF Antenna Input  
F-Type  
France Type  
Front Video Input  
Rear Video Input  
Rear Video Output  
Front Audio Input  
Rear Audio Input  
Rear Audio Output  
21 Pin  
(RCA ø8.3)  
(RCA ø8.3)  
(RCA ø8.3)  
(RCA ø8.3)  
(RCA ø8.3)  
(RCA ø8.3)  
DC Jack(Center +)  
AC Outlet  
S Input(Front)  
Ear Phone Jack(ø3.5)  
Ext Speaker  
S Input(Rear)  
Head Phone Jack(ø3.5)  
Diversity  
G-24.Indicator  
Power  
)
Stand By  
On Timer  
NONE  
(
(
)
(
)
G-25.Display  
On Screen Display  
Menu  
Clock Set( 12H 24H)  
Hotel Lock  
System Selec  
Area Code  
NICAM Auto Off  
Audio  
Pin Code Registration  
Brightness  
Tint(NTSC Only)  
Bass  
Back Light  
Picture Menu  
Mid Night Theater  
GAME  
On/Off Timer  
CH Tuning  
Picture  
Language  
V-Chip  
Contrast  
Sharpness  
Treble  
Sound 1/2  
Guide CH Set  
CATV  
Control Level  
Sound  
Color  
Tuning  
Balance  
Stereo,Audio Output,Bilingual  
Stereo,Audio Output, SAP  
Stereo,Audio Output  
AV  
Sleep Timer  
Channel  
Sound Mute  
Clock  
Pin Code  
Hotel Lock  
A3-2  
GENERAL SPECIFICATIONS  
G-26.OSD Language  
Eng  
Ger  
Fre  
Fre  
Spa  
Spa  
Ita  
Ita  
Por  
Por  
Jpn  
Jpn  
OSD Language Setting  
Eng  
Ger  
Not Applicable  
G-27.Speaker  
Position  
Size  
Imp.  
Front  
1.5 x 2.7 inches  
Side  
pcs  
Bottom  
4
ohm x  
075 + 0.75  
0.5 + 0.5 W (Typical)  
2
Power  
Max  
10%  
W
G-28.EXT Speaker  
Yes  
--  
W
Imp  
No Need  
--  
ohm  
G-29.Carton  
Master Carton:  
Content:  
Need  
---- Set  
---- ----  
---- mm(W)  
Description of Origin Yes  
Gift Box  
Material  
Material:  
/
Corrugated Carton  
---- mm(D)  
No  
Dimensions:  
---- mm(H)  
Double/Brown Corrugated Carton ( with Photo Label)  
Double/White Corrugated Carton ( with Photo Label)  
Double Full Color Carton W/Photo  
Dimensions:  
Design:  
689 mm(W)  
As Per BUYER 's  
577 mm(D)  
620 mm(H)  
Description of Origin:  
Yes  
No  
Drop Test  
Natural Dropping At 1 Corner / 3 Edges / 6 Surfaces  
Height 25cm 31cm 46cm  
204 Sets / 40' container  
62cm  
80cm  
Container Stuffing:  
G-30.Accessories  
Owner's Manual ( W/Guarantee Card) [ English/French ]  
AC Plug Adapter  
Battery (UM- 4 x 2  
Safety Tip  
Channel Film  
Remote Control Unit  
Toll Free Insert Sheet  
)
Guarantee Card  
Registration Card  
Quick Set-Up Sheet  
Information Sheet  
Audio-Video Cord (RCA)  
Warning Sheet  
Schematic Diagram  
U/V Mixer  
75 ohm Coaxial Cable ( Single Shield  
300 ohm to 75 ohm VHF Antenna Adaptor  
21pin Cable  
Double Shield)  
Car Cord  
Rod Antenna  
One Pole  
Loop Antenna  
G-31.Other Features  
Two Pole ( F-Type  
F-Type  
Din Type  
Din Type  
France Type)  
France Type)  
(
Auto Degauss  
Auto Shut Off  
Canal+  
CATV(181CH)  
Anti-Theft  
Rental  
Auto Search  
CH Allocation  
SAP  
Channel Lock  
Just Clock Function  
Game Position  
TopText  
Full OSD  
Premiere  
Comb Filter  
Auto CH Memory  
Hotel Lock  
Fastext  
Closed Caption  
V-Chip  
Unitext  
Picture Menu  
Mid Night Theater  
A3-3  
GENERAL SPECIFICATIONS  
G-32.Switch  
Front  
Power(Tact)  
System Select  
Main Power SW  
Channel Up/Reset  
Channel Down/Enter  
Sub Power  
Volume Up/Set Up  
Volume Down/Set Down  
Menu:Vol UP + Vol Down  
Rear  
AC/DC  
Degauss  
TV/CATV Selector  
Main Power SW  
G-33.Magnetic Field  
BV :  
BH :  
BV :  
BH :  
+0.45G  
0.18G  
-0.15G  
0.15G  
BV :  
BH :  
BV :  
BH :  
+0.35G  
0.30G  
-0.25G  
0.15G  
BV :  
+0.25G  
0.30G  
-0.50G  
0.30G  
BH  
:
BV :  
BH :  
G-34.Remote Control Unit:  
Glow in Dark Remocon  
RC- 74  
Yes  
No  
Power Source:  
D.C  
3
V
Battery UM - 4 x 2  
Total 26 Key  
Power  
Stand By  
0
1
2
3
4
5
Quick View  
Status  
Time Select  
Time Set  
Muting  
CH Skip  
CH1/CH2  
Channel  
Text/Mix/TV  
Display Cancel  
Initial  
TV/AV  
Bar Select  
PAL/SECAM  
Volume Up  
Volume Down  
CH Call  
CH Down  
CH Up  
CH Down/Page Down  
CH Up/Page Up  
Page +/-  
6
7
8
9
Store  
Program  
10  
Reveal  
F/T/B  
11  
Sleep  
Hold  
12  
1
Aft/Skip  
Preset  
List  
Rotate  
2
0/10  
Tone 1/2  
Info  
Mono/Auto  
5.5/6.5MHz  
Auto Memory  
Auto  
Call  
Reset  
Browse  
Std/Auto  
Memory  
Band Select  
Search  
TV/Caption/Text  
Expand  
Red  
Menu  
Enter  
Add  
Clock/Program  
Clock/Set  
Ch Set  
Cyan  
Delete  
Set +  
Normal  
Yellow  
Set -  
Color System  
Wide Selecy  
Auto Wide On/Off  
Picture Position  
Direct Change/Auto Search  
Picture Menu  
Random  
Tuning Up/Time Text  
Tuning Down/Reset  
Navi  
Green  
Nicam/Mono  
Tone A/B  
FM Transmitter  
Back Light  
Audio Select  
Mid Night Theater  
A3-4  
DISASSEMBLY INSTRUCTIONS  
3. After one side is removed, pull in the opposite direction to  
remove the other.  
1. REMOVAL OF ANODE CAP  
Read the following NOTED items before starting work.  
NOTE  
* After turning the power off there might still be a potential  
voltage that is very dangerous. When removing the  
Anode Cap, make sure to discharge the Anode Cap's  
potential voltage.  
Take care not to damage the Rubber Cap.  
INSTALLATION  
1. Clean the spot where the cap was located with a small  
*
Do not use pliers to loosen or tighten the Anode Cap  
terminal, this may cause the spring to be damaged.  
amount of alcohol. (Refer to Fig. 1-3.)  
REMOVAL  
1. Follow the steps as follows to discharge the Anode Cap.  
(Refer to Fig. 1-1.)  
Location of Anode Cap  
Connect one end of an Alligator Clip to the metal part of a  
flat-blade screwdriver and the other end to ground.  
While holding the plastic part of the insulated Screwdriver,  
touch the support of the Anode with the tip of the  
Screwdriver.  
A cracking noise will be heard as the voltage is discharged.  
GND on the CRT  
Fig. 1-3  
NOTE  
Confirm that there is no dirt, dust, etc. at the spot where  
the cap was located.  
2. Arrange the wire of the Anode Cap and make sure the  
wire is not twisted.  
3. Turn over the Rubber Cap. (Refer to Fig. 1-4.)  
CRT  
Screwdriver  
Support  
Alligator Clip  
GND on the CRT  
Fig. 1-1  
2. Flip up the sides of the Rubber Cap in the direction of the  
arrow and remove one side of the support.  
(Refer to Fig. 1-2.)  
Rubber Cap  
Fig. 1-4  
CRT  
Support  
Fig. 1-2  
B-1  
DISASSEMBLY INSTRUCTIONS  
4. Insert one end of the Anode Support into the anode button,  
then the other as shown in Fig. 1-5.  
Support  
CRT  
Fig. 1-5  
5. Confirm that the Support is securely connected.  
6. Put on the Rubber Cap without moving any parts.  
2. REMOVAL OF DEFLECTION YOKE  
(Refer to Fig. 2-1)  
1. Loosen the screw 1.  
2. Remove the Convergence • Purity Magnet in the  
direction of arrow (A).  
3. Loosen the screw 2.  
4. Remove the 3 Wedges.  
5. Remove the Deflection Yoke in the direction of arrow  
(B).  
2
1
Wedge  
(B)  
(A)  
Convergence •  
Purity Magnet  
Deflection Yoke  
Wedge  
Fig. 2-1  
INSTALLATION  
Install new Deflection Yoke in reverse steps of REMOVAL.  
NOTE  
After adjusting the purity and the convergence, fix the  
screw 2 and lock the wedges.  
B-2  
SERVICE MODE LIST  
This unit provided with the following SERVICE MODES so you can repair, examine and adjust easily.  
To enter the Service Mode, press both set key and remote control key for more than 1 second.  
Set Key  
Remocon Key  
Operations  
0
Releasing of V-CHIP PASSWORD.  
Initialization of the factory.  
VOL. (-) MIN  
VOL. (-) MIN  
VOL. (-) MIN  
1
6
NOTE: Do not use this for the normal servicing.  
POWER ON total hours is displayed on the screen.  
Refer to the "CONFIRMATION OF USING HOURS".  
Can be checked of the INITIAL DATA of MEMORY IC.  
Refer to the "NOTE FOR THE REPLACING OF MEMORY IC".  
Writing of EEPROM initial data.  
NOTE: Do not use this for the normal servicing.  
VOL. (-) MIN  
VOL. (-) MIN  
8
9
Display of the Adjustment MENU on the screen.  
Refer to the "ELECTRICAL ADJUSTMENT" (On-Screen Display Adjustment).  
CONFIRMATION OF USING HOURS  
POWER ON total hours can be checked on the screen. Total hours are displayed in 16 system of notation.  
ADDRESS  
DATA  
1. Set the VOLUME to minimum.  
2. Press both VOL. DOWN button on the set and Channel  
button (6) on the remote control for more than 1 second.  
3. After the confirmation of using hours, turn off the power.  
Initial setting content of MEMORY IC.  
INIT 00 83  
0010  
POWER ON total hours.  
= (16 x 16 x 16 x thousands digit value)  
+ (16 x 16 x hundreds digit value)  
+ (16 x tens digit value)  
CRT ON  
FIG. 1  
+ (ones digit value)  
NOTE FOR THE REPLACING OF MEMORY IC  
If a service repair is undertaken where it has been required to change the MEMORY IC, the following steps should be taken to  
ensure correct data settings while making reference to TABLE 1.  
INI INI INI INI INI INI INI INI INI INI INI  
ADDRESS  
00 01 02 03 04 05 06 07 08 09 0A  
DATA  
A0 01 A2 09 02 63 24 18 A1 21  
44  
Table 1  
1.  
2.  
Enter DATA SET mode by setting VOLUME to minimum.  
Press both VOL. DOWN button on the set and Channel button (6) on the remote control for more than 1 second.  
ADDRESS and DATA should appear as FIG 1.  
3.  
ADDRESS is now selected and should "blink". Using the SET + or - keys on the remote, step through the ADDRESS until  
required ADDRESS to be changed is reached.  
4.  
5.  
6.  
7.  
8.  
Press ENTER to select DATA. When DATA is selected, it will "blink".  
Again, step through the DATA using SET + or - until required DATA value has been selected.  
Pressing ENTER will take you back to ADDRESS for further selection if necessary.  
Repeat steps 3 to 6 until all data has been checked.  
When satisfied correct DATA has been entered, turn POWER off (return to STANDBY MODE) to finish DATA input.  
The unit will now have the correct DATA for the new MEMORY IC.  
C-1  
ELECTRICAL ADJUSTMENTS  
1. BEFORE MAKING ELECTRICAL  
2. BASIC ADJUSTMENTS  
ADJUSTMENTS  
2-1: RF AGC DELAY  
Read and perform these adjustments when repairing the  
circuits or replacing electrical parts or PCB assemblies.  
1. Receive an 80dB monoscope pattern.  
2. Connect the digital voltmeter to TP001.  
3. Activate the adjustment mode display of Fig. 1-1 and  
press the channel button (02) on the remote control to  
select "RF DELAY".  
4. Press the VOL. UP/DOWN button on the remote control  
until the digital voltmeter is 1.80 ± 0.05V.  
CAUTION  
• Use an isolation transformer when performing any  
service on this chassis.  
• Before removing the anode cap, discharge electricity  
because it contains high voltage.  
• When removing a PCB or related component, after  
unfastening or changing a wire, be sure to put the wire  
back in its original position.  
Inferior silicon grease can damage IC's and transistors.  
• When replacing IC's and transistors, use only specified  
silicon grease (YG6260M).  
2-2: CUT OFF  
1. Adjust the unit to the following settings.  
R.DRIVE=10, B.DRIVE=10, R.BIAS=64, G.BIAS=64,  
B.BIAS=64, BRIGHTNESS=126, CONTRAST=100.  
2. Place the set with Aging Test for more than 15 minutes.  
3. Activate the adjustment mode display of Fig. 1-1 and  
press the channel button (01) on the remote control to  
select "CUT OFF".  
Remove all old silicon before applying new silicon.  
Prepare the following measurement tools for electrical  
adjustments.  
4. Adjust the Screen Volume until a dim raster is obtained.  
1. Synchro Scope  
2. Digital Voltmeter  
2-3: WHITE BALANCE  
NOTE: Adjust after performing CUT OFF adjustment.  
On-Screen Display Adjustment  
1. Place the set with Aging Test for more than 10 minutes.  
2. Receive the with 100% signal from the pattern generator.  
3. Using the remote control, set the brightness and contrast to  
normal position.  
4. Activate the adjustment mode display of Fig. 1-1 and press  
the channel button (10) on the remote control to select  
"R.BIAS".  
1. In the condition of NO indication on the screen.  
Press the VOL. DOWN button on the set and the  
Channel button (9) on the remote control for more than  
1 second to appear the adjustment mode on the screen  
as shown in Fig. 1-1.  
5. Using the VOL. UP/DOWN button on the remote control,  
adjust the R.BIAS.  
TV  
6. Press the CH. UP/DOWN button on the remote control to  
select the "R.DRIVE", "B.DRIVE", "G.BIAS" or "B.BIAS".  
7. Using the VOL. UP/DOWN button on the remote control,  
adjust the R.DRIVE, B.DRIVE, G.BIAS or B.BIAS.  
8. Perform the above adjustments 6 and 7 until the white  
color is looked like a white.  
00 OSD  
15  
Fig. 1-1  
2-4: FOCUS  
2. Use the Channel UP/DOWN button or Channel button  
(0-9) on the remote control to select the options shown  
in Fig. 1-2.  
3. Press the MENU button on the remote control to end  
the adjustments.  
1. Receive the monoscope pattern.  
2. Turn the Focus Volume fully counterclockwise once.  
3. Adjust the Focus Volume until picture is distinct.  
2-5: SUB TINT/SUB COLOR  
1. Receive the color bar pattern.  
NO. FUNCTION  
00 OSD H  
01 CUT OFF  
02 RF DELAY  
03 VIF VCO  
04 H VCO  
05 H PHASE  
06 V SIZE  
07 V SHIFT  
08 R DRIVE  
09 B DRIVE  
10 R BIAS  
NO. FUNCTION  
13 BRIGHTNESS  
14 CONTRAST  
15 COLOR  
2. Connect the synchro scope to TP023.  
3. Activate the adjustment mode display of Fig. 1-1 and  
press the channel button (16) on the remote control to  
select "TINT".  
4. Press the VOL. UP/DOWN button on the remote control  
until the waveform becomes as shown in Fig. 2-1.  
5. Connect the synchro scope to TP022.  
6. Press the CH DOWN button once to set to "COLOR"  
mode.  
16 TINT  
17 SHARPNESS  
18 FM LEVEL  
19 LEVEL  
20 SEPARATION 1  
21 SEPARATION 2  
22 TEST MONO  
23 TEST STEREO  
24 X-RAY TEST  
7. Press the VOL. UP/DOWN button on the remote control  
until the red color level is adjusted to 110% of the white  
level. (Refer to Fig. 2-2)  
11 G BIAS  
12 B BIAS  
Fig. 1-2  
D1-1  
ELECTRICAL ADJUSTMENTS  
TV  
Fig. 2-1  
00 OSD  
15  
A
B
Fig. 2-3  
0%  
2-9: OSD HORIZONTAL  
110%  
1. Activate the adjustment mode display of Fig. 1-1.  
2. Press the VOL. UP/DOWN button on the remote  
control until the difference of A and B becomes  
minimum. (Refer to Fig. 2-3)  
100%  
Fig. 2-2  
2-10: VERTICAL VCO  
1. Place the set with Aging Test for more than 15 minutes.  
2. Receive an 80dB monoscope pattern.  
3. Connect the digital voltmeter between the pin 5 of  
CP601.  
4. Activate the adjustment mode display of Fig. 1-1 and  
press the channel button (03) on the remote control to  
select "VIF VCO".  
2-6: HORIZONTAL PHASE  
1. Receive the center cross signal from the Pattern  
Generator.  
2. Using the remote control, set the brightness and  
contrast to normal position.  
Fig. 1-1 and  
(05) on the remote control to  
3. Activate the adjustment mode display of  
5. Press the VOL. UP/DOWN button on the remote control  
until the digital voltmeter is 2.5V.  
press the channel button  
select "H.PHASE".  
4. Press the VOL. UP/DOWN button on the remote  
control until the SHIFT quantity of the OVER SCAN on  
right and left becomes minimum.  
2-11: SUB BRIGHTNESS  
1. Receive the black pattern*. (RF Input)  
2. Activate the adjustment mode display of Fig. 1-1 and  
press the channel button (13) on the remote control to  
select "BRIGHTNESS".  
3. Press the VOL. UP/DOWN button on the remote control  
unit the screen begin to shine.  
2-7: VERTICAL SIZE  
NOTE: Adjust after performing adjustments in section 2-6  
1. Receive the crosshatch signal from the Pattern  
Generator.  
2. Using the remote control, set the brightness and  
contrast to normal position.  
2-12: SUB CONTRAST  
Fig. 1-1 and  
3. Activate the adjustment mode display of  
1. Receive the color bar pattern.  
(06) on the remote control to  
2. Activate the adjustment mode display of Fig. 1-1 and  
press the channel button (14) on the remote control to  
select "CONTRAST".  
3. Press the VOL. UP/DOWN button on the remote control  
unit the nit for more than 200 nit.  
press the channel button  
select "V.SIZE".  
4. Press the VOL. UP/DOWN button on the remote control  
until the rectangle on the center of the screen becomes  
square.  
5. Receive a broadcast and check if the picture is normal.  
2-8: VERTICAL SHIFT  
NOTE: Adjust after performing adjustments in section 2-7  
1. Receive the crosshatch signal from the Pattern  
Generator.  
2. Using the remote control, set the brightness and  
contrast to normal position.  
Fig. 1-1  
3. Activate the adjustment mode display of  
(07) on the remote control to  
and press the channel button  
select "V.SHIFT".  
4. Press the VOL. UP/DOWN button on the remote  
control until the horizontal line becomes fit to the notch  
of the shadow mask.  
D1-2  
ELECTRICAL ADJUSTMENTS  
3-3: STATIC CONVERGENCE  
NOTE  
Adjust after performing adjustments in section 3-2.  
3. PURITY AND CONVERGENCE  
ADJUSTMENTS  
NOTE  
1. Receive the crosshatch pattern from the color bar  
generator.  
2. Combine red and blue of the 3 color crosshatch pattern  
on the center of the screen by adjusting the pair of  
4 pole magnets.  
1. Turn the unit on and let it warm up for at least 30  
minutes before performing the following adjustments.  
2. Place the CRT surface facing east or west to reduce the  
terrestrial magnetism.  
3. Turn ON the unit and demagnetize with a Degauss Coil.  
3. Combine red/blue (magenta) and green by adjusting the  
pair of 6 pole magnets.  
3-1: STATIC CONVERGENCE (ROUGH ADJUSTMENT)  
1. Tighten the screw for the magnet. Refer to the adjusted  
CRT for the position. (Refer to Fig. 3-1)  
If the deflection yoke and magnet are in one body,  
untighten the screw for the body.  
2. Receive the green raster pattern from the color bar  
generator.  
3. Slide the deflection yoke until it touches the funnel  
side of the CRT.  
4. Adjust center of screen to green, with red and blue on the  
sides, using the pair of purity magnets.  
5. Switch the color bar generator from the green raster  
pattern to the crosshatch pattern.  
6. Combine red and blue of the 3 color crosshatch pattern  
on the center of the screen by adjusting the pair of  
4 pole magnets.  
7. Combine red/blue (magenta) and green by adjusting the  
pair of 6 pole magnets.  
3-4: DYNAMIC CONVERGENCE  
NOTE  
Adjust after performing adjustments in section 3-3.  
1. Adjust the differences around the screen by moving  
the deflection yoke upward/downward and right/left.  
(Refer to Fig. 3-2-a)  
2. Insert three wedges between the deflection yoke and  
CRT funnel to fix the deflection yoke.  
(Refer to Fig. 3-2-b)  
R G B  
R G B  
R
G
B
8. Adjust the crosshatch pattern to change to white  
by repeating steps 6 and 7.  
R
G
B
3-2: PURITY  
UPWARD/DOWNWARD SLANT RIGHT/LEFT SLANT  
NOTE  
Fig. 3-2-a  
Adjust after performing adjustments in section 3-1.  
1. Receive the green raster pattern from color bar  
generator.  
2. Adjust the pair of purity magnets to center the  
color on the screen.  
Adjust the pair of purity magnets so the color at the  
ends are equally wide.  
WEDGE  
WEDGE  
3. Move the deflection yoke backward (to neck side)  
slowly, and stop it at the position when the whole  
screen is green.  
4. Confirm red and blue colors.  
5. Adjust the slant of the deflection yoke while watching the  
screen, then tighten the fixing screw.  
WEDGE  
DEFLECTION YOKE  
DEFLECTION YOKE SCREW  
MAGNET SCREW  
WEDGE POSITION  
Fig. 3-2-b  
PURITY MAGNETS  
6 POLE MAGNETS  
4 POLE MAGNETS  
Fig. 3-1  
D2-1  
MAJOR COMPONENTS LOCATION GUIDE  
TU001  
FB401  
TP001  
CP601  
FOCUS VOLUME  
SCREEN VOLUME  
MAIN PCB  
TP023  
TP024  
J801  
TP022  
CRT PCB  
D3-1  
BLOCK DIAGRAM  
Q351  
MUTE SW.  
TU001  
11  
CHROMA IC  
IC601 M61203BFP  
CH UP  
X602  
3.579545MHz  
IC351 AN7523  
4
VOL UP  
CH DOWN  
VOL DOWN  
POWER  
1
X' TAL  
5
32  
AUDIO OUT  
REG OUT  
50  
33  
6
2
4
MICON IC  
IC101 OEC7044A  
SOUND IC  
SP351  
62  
RF AGC OUT  
CF601  
SAW FILTER  
9
64  
1
VIF IN (1)  
VIF IN (2)  
Q606  
REG.  
5
AUDIO MUTE  
KEY2  
P. CON+15V  
26  
Q801  
RED OUT  
CVIN  
40  
30  
28  
20  
Y SW OUT  
R IN  
17  
R OUT  
G OUT  
RED R 42  
14  
15  
KEY1  
27  
41  
40  
39  
Q803  
GREEN G  
BLUE B  
G IN  
GREEN OUT  
B OUT 16  
B IN  
Q603  
REG.  
OS101  
BLANK BL  
10 REMOCON  
Q802  
27 FAST BLK  
REG OUT  
41  
6
1
2
3
BLUE OUT  
H. SYNC  
1
12  
29  
5
INV FBP OUT  
V PULSE OUT  
SCL  
FBP IN  
Q608  
V. SYNC  
SCL1  
2
CUT OFF  
START UP  
VCC  
19  
7
34  
32  
25  
POWER  
SDA1  
36  
H OUT  
SDA  
10  
42  
RESET  
19 XIN  
MCU RESET  
X101  
8MHz  
Q402  
H. DRIVE  
Q401  
H. OUTPUT  
VREG VCC  
55  
6
5
SDA  
MEMORY IC  
SCL IC199  
S-24C02BDP-1A  
17 V OUT  
XOUT  
20  
Q101  
Q501  
POWER  
X_RAY_TEST  
30  
X-RAY TEST SW  
V-OUT IC  
IC401 LA78041  
POWER REG. IC  
IC501  
STR30110  
PUMP UP  
6
11  
B
8
G
R
-
CRT  
AMP  
DEGAUSS COIL  
L502  
+
Heater  
10  
4
3
Q403  
X-RAY TEST SW.  
VCC  
6
9
F
D501~D504  
RECTIFIER  
7
2
5
+B  
RY101  
1
IC402  
KIA7805API  
4
3
P. CON+5V  
REG IC  
DY  
2
1
3
FB401  
D127  
L501  
4
1
P. CON+5V  
9
F
1
2
3
5
D404  
5
S
10  
HV  
3
F501  
AC IN  
E-1  
E-2  
PRINTED CIRCUIT BOARDS  
MAIN/CRT (INSERTED PARTS)  
SOLDER SIDE  
CP802A  
D405  
R422  
C401  
TP501  
CP803A  
CP601  
R509  
W010  
TU001  
D605  
TP001  
R001  
R429_1  
IC501  
D410  
D422  
HS501  
R002  
C404  
C412  
W818  
C004  
D408  
D404  
FB401  
D401  
W019  
L406  
R503  
D407  
D402  
R508  
Q403  
R506  
W004  
R412  
W897  
W088  
W074  
R410  
W014  
S104Y  
CP401_1  
R427  
W831  
W817  
HS401  
W813  
IC401  
R502  
*
R417  
W059  
T401_1  
*
S803X  
R407_2  
W823  
W824  
R177  
IC351_1  
C359_1  
R655  
R448_1  
C133  
C506_1  
S801Y  
D126  
R640  
D127  
S801X  
D609  
C351  
Q351  
W007  
C647  
RY101  
D617  
CP351_1  
S809Y  
R443_1  
S809X  
S802Y  
Q606  
CP502  
L501  
CF604  
CF603  
CC004  
CP802B  
C630  
W092  
S104X  
C631  
D608  
Q801  
W805  
C636  
C624  
IC402  
W108  
Q501  
C129  
IC199  
S803Y  
W812  
Q101  
L601  
S106Y  
Q802  
Q803  
TP023  
S106X  
R815  
C625  
CF601  
S105Y  
Q603  
TP022  
TP024  
C125  
R806  
W042  
W041  
C661  
C639  
*
W071  
D603  
W011  
W806  
W837  
X101_1  
L603  
W029  
C802_1  
CP803B  
D610  
CP806  
FH502  
F501 FH501  
D104  
SW102  
SW105  
D612  
6.3A125V  
D103  
OS101  
SW104  
SW101  
SW103  
F-1  
F-2  
PRINTED CIRCUIT BOARDS  
MAIN/CRT (CHIP MOUNTED PARTS)  
SOLDER SIDE  
R638  
C113  
R642  
C699  
17  
IC601  
49  
IC101  
C634_1  
1
33  
R603  
R111  
C642  
R611  
F-4  
F-3  
A
B
C
D
E
F
G
H
MICON/TUNER SCHEMATIC DIAGRAM  
(MAIN PCB)  
8
8
TU001 NJH3021U268  
ACCESORY  
ATC001  
NXC0032-010010  
TP001  
TM101  
R25-1127  
C003  
FROM DEFLECTION/CRT  
P_CON+5V  
50V4.7 KA  
7
7
OS101  
PIC-28143SY-2  
FROM POWER  
GND  
R001  
S809X  
+B  
68K1/2W  
R002  
FROM/TO CHROMA  
68K 1/2W  
AGC  
IF  
6
6
I2C_OFF  
VD  
HD  
MICON IC  
IC101  
3
OEC7044A  
RED R  
R123  
0
0
4.9  
OSD_R  
OSD_G  
OSD_B  
P50/H.SYNC  
P51/V.SYNC  
4.7K  
R122  
4.9  
GREEN G  
BLUE B  
4.7K  
R121  
4
0
0
0
P00/EXT MUTE  
P01/I2C_OFF  
P02/AUDIO MUTE  
P03/(Surround)  
P04  
4.7K  
R120  
R116  
47K  
4.9  
0
OSD_BLK  
OUT1/BLANK BL  
P20/AV2  
R117  
47K  
4.7K  
5
5
R111  
10K  
0
NC  
GND  
SCL  
0
0
NC  
P21/AV1  
SDA  
POWER  
4.9  
0
P22/POWER  
0
NC  
0
TO SOUND  
P05/(Center_SP) P10/DEGAUSS_H  
AUDIO_MUTE  
R114  
10K  
4.9  
4.8  
4.8  
3.9  
INT2/P.FAIL  
INT1/REMOCON  
P23/SYNC  
P24  
SCL1  
SCL2  
C117  
0
NC  
270P B  
R105  
TO POWER  
POWER  
D104  
R115  
47K  
4
3
2
4
3
2
MTZJ6.8B  
5.0  
4.7K  
C116  
SDA1  
SDA2  
FROM/TO DEFLECTION/CRT  
X-RAY_TEST  
0
NC  
0
NC  
270P B  
R106  
16.0  
X-RAY TEST SW  
Q101  
DTC114TS  
X-RAY  
0
4.7K  
0
0
NC  
P25/ON_TIMER AD1/X_RAY_TEST  
W812  
R107  
10K  
0
4.9  
3.0  
0
AVCC  
HLF  
X-RAY  
AD4/AFT  
R130  
1K  
C122  
FROM CHROMA  
AFT  
C121  
3.2  
4.9  
50V1 KA  
200P CH  
D101  
MTZJ6.8B  
MTZJ6.8B  
C120  
FROM CHROMA  
SYNC  
0.8  
3.4  
0
V.HOLD  
CVIN  
CNVSS  
Xin  
AD5/KEY1  
AD6/KEY2  
R112  
0.001 Y  
C124  
D103  
2
4.9  
4.9  
2.2K  
R113  
Y_VIDEO  
50V 0.1 KA  
AT+5V  
RESET  
C130  
0.001  
R119  
1K  
2.2K  
RESET  
OSC1  
B
C114  
10P CH  
1
3.7  
4.2  
0
3.6  
C113  
Xout  
OSC2  
VCC  
4.1  
4.9  
X101_1  
CST8.00MTW  
10P CH  
VSS  
C119  
5.0  
5.0  
0
5.0  
0.68 TF  
C118  
R126  
2.7K  
R101  
560  
5
4
6
3
7
2
8
1
R128  
560  
6.3V 470  
YK  
0
0
0
0
THE DC VOLTAGE AT EACH PART WAS MEASURED  
NOTE:THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME  
OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE  
CAUTION: SINCE THESE PARTS MARKED BY  
CRITICAL FOR SAFETY,USE ONES  
ARE  
ATTENTION: LES PIECES REPAREES PAR UN  
ETANT  
CAUTION: DIGITAL TRANSISTOR  
NOTE:  
TUNER VIDEO SIGNAL  
R.SIGNAL  
DANGEREUSES AN POINT DE VUE SECURITE  
NUTILISER QUE CELLS DECRITES  
WITH THE DIGITAL TESTER WHEN THE COLOR BROADCAST  
WAS RECEIVED IN GOOD CONDITION AND PICTURE IS NORMAL.  
DESCRIBED IN PARTS LIST ONLY  
1
1
PCB010  
TMX456  
G.SIGNAL  
DANS LA NOMENCLATURE DES PIECES  
B.SIGNAL  
DEFLECTION SIGNAL  
A
B
C
D
E
F
G
H
G-1  
G
-2  
A
B
C
D
E
F
G
H
CHROMA SCHEMATIC DIAGRAM  
8
8
(MAIN PCB)  
TO MICON/TUNER  
SYNC  
Y_VIDEO  
AT+5V  
6
4.8  
10.6  
5.5  
FROM POWER  
P_CON+15V  
REG.  
Q603  
8.2  
8.8  
15.0  
REG.  
2SD734  
7
7
S802Y S802X  
RESET  
7
Q606  
2SD734  
CF604  
EFCT4R5MW5  
FROM POWER  
AT+15V  
W828  
R615  
470  
CF603  
EFCT4R5YS5A  
R638 6.8K  
D607  
C661 0.01 Y  
R646 12K  
1SS133  
6
6
2.9 2.3  
0
46  
8.2  
45  
8.2 3.9 4.8 5.5 3.4 0 NC  
44 43 42 41 40 39  
0
0
2.9 3.3 2.0 8.8  
TO SOUND  
GND  
48  
47  
38  
37  
36  
35  
34  
33  
C638  
R634  
10K  
10K  
2.3  
3.0  
2.3  
3.2  
3.5  
2.6  
50V4.7 NA  
D605  
R611  
5
R612  
5.6K  
R642  
100K  
AUDIO_OUT  
11E1-EIC  
C604 50V 1 KA  
0
AUDIO BYPASS  
EXT AUDIO IN  
R IN  
C642 0.001  
Y
5.0  
0
V PULSE OUT  
G OUT  
C623 0.0033  
M
3.8  
3.1  
9.2  
3.0  
2.6  
0
FM DIRECT OUT  
VIF VCO F/B  
46 SW REG CONT  
47 LIMITER IN  
48 IF AGC  
34 EXT C in  
33 8.7V REG OUT  
32 X’TAL  
C632 50V 2.2 KA  
0
FAST BLK  
SPOT KILLER  
fsc OUT  
R618 10M1/4W  
5
5
C610  
49 QIF OUT  
31 ACL/ABCL  
7.3  
VREG Vcc  
50 AUDIO OUT  
50V 0.22 YK  
C645  
0
NC  
VIF APC FILTER  
VIF VIDEO OUT  
VIF GND  
16V 47 YK  
D614  
5.0  
5.0  
5.6  
2.5  
FROM/TO DEFLECTION/CRT  
MTZJ6.2B  
VIDEO CHROMA Vcc  
V RAMP CAP  
S106Y  
ABCL  
C613_1  
TF  
0
1
C621 0.01  
B
P_CON+5V  
V_FEEDBACK  
R641  
20K  
3.2  
2.9  
1.8  
AFT OUT  
QIF IN  
V RAMP FEEDBACK  
B IN  
W819  
C626  
64 VIF IN  
1 VIF IN  
17 V OUT  
16 B OUT  
0
D615 MTZJ6.2B  
0.001 Y  
R606  
10K  
8.2  
4
3
2
4
3
2
RF AGC OUT  
STRAT UP Vcc  
C654 0.022  
F
C606  
50V 0.1 KA  
2.9  
1.8  
CHROMA IC  
IC601  
RF AGC FILTER  
8.2  
4.5  
SAW FILTER  
CF601  
SAF45MFY220ZR  
R644  
V_OUT  
GND  
1001/4W  
D616  
10  
5
4
3
2
M61203BFP  
1
2
3
4
5
6
7
8
9
10  
4.9  
11  
12  
13  
14  
15  
16  
4.8  
0
1.5  
5.0 5.0  
2.7 4.9  
6.2 6.2  
0
3.5 4.9 4.9 4.0 4.0  
MTZJ6.2B  
11  
12  
13  
9
H_OUT  
H_SYNC  
R627 100  
R630 100  
R631 100  
8
B.OUT  
G.OUT  
R.OUT  
CLAMP  
FROM/TO MICON/TUNER  
L601  
1.2uH  
TEST POINT  
AFT  
AGC  
IF  
R617 2.7K  
CP601  
TKC-M06X-A1  
CUT OFF  
Q608  
2SA1015Y  
B.OUT  
6
5
4
3
2
1
0.8  
0
D603  
D604  
INT.MONI  
IIC_OFF  
SDA  
GND  
0.1  
1SS133 1SS133  
HD  
POWER  
OSD_B  
OSD_BLK  
OSD_G  
VD  
SCL  
GND  
OSD_R  
I2C_OFF  
SDA  
SCL  
DEFLECTION SIGNAL  
AUDIO SIGNAL  
LUMINANCE SIGNAL  
TUNER VIDEO SIGNAL  
R.SIGNAL  
G.SIGNAL  
B.SIGNAL  
THE DC VOLTAGE AT EACH PART WAS MEASURED  
NOTE:  
NOTE:THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME  
OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE  
WITH THE DIGITAL TESTER WHEN THE COLOR BROADCAST  
WAS RECEIVED IN GOOD CONDITION AND PICTURE IS NORMAL.  
PCB010  
TMX456  
1
1
A
B
C
D
E
F
G
H
G-3  
G-4  
A
B
C
D
E
F
G
H
(MAIN PCB)  
DEFLECTION/CRT SCHEMATIC DIAGRAM  
CD802  
8
8
2E054401  
GND  
GND  
FROM/TO CHROMA  
GND  
CLAMP  
G.OUT  
B.OUT  
R.OUT  
5
4
3
2
1
5
4
3
2
1
GND  
CLAMP  
G.OUT  
B.OUT  
R.OUT  
CLAMP  
G.OUT  
B.OUT  
R.OUT  
CLAMP  
G.OUT  
CLAMP  
G.OUT  
B.OUT  
R.OUT  
B.OUT  
R.OUT  
V-OUT IC  
IC401 LA78041  
V_OUT  
CP802A  
CP802B  
51048-0510  
51048-0510  
V_FEEDBACK  
HS401  
763WAA0119  
L802  
HF57T18.5*10*10  
THERMAL  
PROTECTION  
PUMP  
UP  
CD801_1  
8M82025A  
CP801_1  
TS-80P-02-V1  
-
AMP  
+
1
2
VCC  
6
1
2
7
7
W831  
1
2
3
4
5
7
4.5 25.1 27.0  
0
53.0  
52.0  
4.4  
W817  
14  
3.2  
3.2  
3.2  
2.7  
18  
D403  
100.6  
2.7  
98.4  
2.7  
95.4  
V801  
19  
11E1-EIC  
A63AHC26X  
RED OUT  
Q801  
2SC4075-YAC  
GREEN OUT  
Q803  
2SC4075-YAC  
BLUE OUT  
Q802  
2SC4075-YAC  
R418  
9
10  
8
R
22K +-1%  
CC004  
R420  
6.8K  
G
6
6
6
B
11  
CC002  
CC006  
5
7
1
DY801  
7M062505  
TO DY  
TP022  
TP023  
TP024  
S803X  
4
3
2
1
4
3
2
1
R404  
2.7K 1/4W  
20  
22  
21  
X-RAY TEST SW.  
Q403  
DTA144ES  
MG801  
29MMSTAR  
R405  
18K 1/4W  
+-1%  
5
5
16.0  
9.6  
R401  
16.1  
CP401_1  
100K 1/4W  
+-1%  
TS-80P-04-V1  
C434  
100V 22 YK  
FROM/TO MICON/TUNER  
D402  
R424  
R409  
6.2K +-1%  
K001  
8115529  
X-RAY  
X-RAY_TEST  
P_CON+5V  
HZ11B1L  
12K +-1%  
K002  
8115529  
15  
C439  
SL  
500V22P  
K003  
8115529  
FROM/TO CHROMA  
H.DRIVE  
Q402  
2SC2621  
R429_1  
GND  
ABCL  
FB401  
3225010F  
4
3
2
4
3
2
1.8 2W  
0
R
B
G
27.0  
0
17.7  
W897  
17  
H_OUT  
0
COL  
130.0  
0.3  
1
HV  
H.OUTPUT  
Q401  
-0.1  
16  
H_SYNC  
P_CON+5V  
45.7  
2SD2499(LBOEC1)  
0
130.0  
T401_1  
5013001  
D410  
AU02A-EIC  
FOCUS  
135.0 VIDEO  
F
S
6
0
SCREEN  
1
B+  
135.0  
2
CP806  
005P-2100  
W891  
GND  
0
11  
P.CON+5V REG IC  
IC402 KIA7805API  
L406 18uH  
C416  
-1.9  
0
AFC  
HEA  
TER  
9
10  
8
ABL  
R428_1  
8.2 2W  
1.7  
7
200V  
PP  
0.018  
R422  
W838  
0
GND  
6.8K 1/2W  
C401  
1.5 E12  
4
GND  
C446  
C404  
8
NC  
2.0 E25  
3
IN  
1
GND OUT  
SL  
500V22P  
E8 0.8  
160V 1 MHE  
10V 470 YK  
5
2
3
7.8  
0
5.0  
D408  
AU02A-EIC  
R448_1  
W823  
W824  
D407  
3.3K 5W  
AU02A-EIC  
96.4  
NC  
TO SOUND  
6.4  
P_CON+5V  
SOUND+B  
0
C448  
22  
R443_1  
R445_1  
D422  
AU02A-EIC  
100V  
YK  
101.6  
100K  
1/4W  
4.7 2W  
0
FROM/TO POWER  
HEATER  
HEATER  
GND  
99.6  
HEATER  
GND  
4
3
2
1
4
3
2
1
J801  
0
GND  
GND  
180V  
CVT3275-5102  
+B  
GND  
GND  
GND  
180V  
180V  
CD803  
2E044101  
CP803A  
51052-0400  
CP803B  
51052-0400  
D404  
FBT+12V  
AU02A-EIC  
PCB110  
TCX315  
PCB010  
TMX456  
CAUTION: DIGITAL TRANSISTOR  
R.SIGNAL  
G.SIGNAL  
B.SIGNAL  
1
1
NOTE:THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME  
OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE  
THE DC VOLTAGE AT EACH PART WAS MEASURED  
CAUTION: SINCE THESE PARTS MARKED BY  
CRITICAL FOR SAFETY,USE ONES  
ARE  
ATTENTION: LES PIECES REPAREES PAR UN  
ETANT  
NOTE:  
DANGEREUSES AN POINT DE VUE SECURITE  
NUTILISER QUE CELLS DECRITES  
DANS LA NOMENCLATURE DES PIECES  
WITH THE DIGITAL TESTER WHEN THE COLOR BROADCAST  
WAS RECEIVED IN GOOD CONDITION AND PICTURE IS NORMAL.  
DESCRIBED IN PARTS LIST ONLY  
DEFLECTION SIGNAL  
A
B
C
D
E
F
G
H
G-5  
G
-
6  
A
B
C
D
E
F
G
H
POWER SCHEMATIC DIAGRAM  
8
8
(MAIN PCB)  
CAUTION:  
FOR CONTINUED PROTECTION AGAINST FIRE HAZARD,  
REPLACE ONLY WITH THE SAME TYPE 6.3A 125V (F501)  
FUSE.  
ATTENTION: POUR UNE PROTECTION CONTINUE LES RISQUES  
DINCEIE NUTILISER QUE DES FUSIBLE DE MEME  
TYPE 6.3A 125V (F501).  
6.3A 125V  
7
7
DEGAUSS COIL  
L502  
8R250009  
R502  
1.2 7W  
2
1
R640  
D609  
EM1C-EIC  
2.2K 10W  
R655  
CP502  
TV-50P-02-A1  
POWER REG.IC  
IC501 STR30110  
C647  
D501  
D502  
6
6
500V 0.001  
B
2.2K 10W  
RM11C-EIC  
RM11C-EIC  
MS501  
23MICA  
D504  
D503  
RY101  
1
2
3
4
5
ALKS321  
3
1
RM11C-EIC  
RM11C-EIC  
TH501  
PTAD14K2-3R0Q141  
0
137.3 179.6 136.6  
6.9  
P
H
2
TP501  
D125  
1SS133  
POWER  
Q501  
HS501  
763WAA0112  
2SC1815Y  
0
R504  
4.7K  
R177  
0.7  
D126  
5
W818  
5
0
EM1C-EIC 1.2K 10W  
C133  
R506  
NC  
AC120V_60HZ  
CD501  
0R614909  
6.3A 125V  
180 20W  
500V 0.001  
B
6.3A 125V  
F501  
L501  
9-000074  
BLACK  
WHITE  
FH502  
EYF-52BC  
FH501  
23706.3  
C501  
EYF-52BC  
250V 0.22 ECQUL  
D617  
11E1-EIC  
C646  
CP501  
THL-P03P-B1  
R515  
1.5 3W  
C132_1  
25V 2200 YK  
D608  
R643  
4
3
2
4
3
2
25V 2200 MHE  
S803Y  
33 1/2W  
RD15FB  
FBT+12V  
D127  
11E1-EIC  
+B  
W801  
W815  
GND  
FROM/TO MICON/TUNER  
FROM/TO DEFLECTION/CRT  
GND  
+B  
POWER  
TO CHROMA  
P_CON+15V  
AT+15V  
NOTE:THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME  
OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE  
THE DC VOLTAGE AT EACH PART WAS MEASURED  
CAUTION: SINCE THESE PARTS MARKED BY  
CRITICAL FOR SAFETY,USE ONES  
ARE  
ATTENTION: LES PIECES REPAREES PAR UN  
ETANT  
NOTE:  
DANGEREUSES AN POINT DE VUE SECURITE  
NUTILISER QUE CELLS DECRITES  
WITH THE DIGITAL TESTER WHEN THE COLOR BROADCAST  
WAS RECEIVED IN GOOD CONDITION AND PICTURE IS NORMAL.  
DESCRIBED IN PARTS LIST ONLY  
1
1
PCB010  
TMX456  
DANS LA NOMENCLATURE DES PIECES  
A
B
C
D
E
F
G
H
G-7  
G-8  
A
B
C
D
E
F
G
H
SOUND SCHEMATIC DIAGRAM  
8
8
FROM MICON/TUNER  
AUDIO_MUTE  
(MAIN PCB)  
FROM CHROMA  
7
7
AUDIO_OUT  
GND  
6
6
5
5
FROM DEFLECTION/CRT  
P_CON+5V  
SPEAKER  
SP351_2  
SA04A05AWA  
CP351_1  
TID-X02P-B2  
SOUND+B  
SOUND IC  
IC351_1  
1
2
1
2
AN7523  
SPEAKER  
4
3
2
4
3
2
SP351_2  
SA04A05AWA  
+
-
+
-
+
-
GND  
VCC  
1
5.7  
2
3
0
4
5
6
7
0
8
9
4.6  
4.6  
4.1  
1.6  
0
2.9  
NC  
W834  
24  
W820  
S801Y  
S801X  
S809Y  
W829  
W810  
23  
W813  
MUTE SW.  
Q351  
2SC1815Y  
2.9  
R354  
47K  
0
0
W814  
PCB010  
TMX456  
1
1
NOTE:THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME  
OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE  
THE DC VOLTAGE AT EACH PART WAS MEASURED  
CAUTION: SINCE THESE PARTS MARKED BY  
ARE  
ATTENTION: LES PIECES REPAREES PAR UN  
ETANT  
NOTE:  
AUDIO SIGNAL  
CRITICAL FOR SAFETY,USE ONES  
DESCRIBED IN PARTS LIST ONLY  
DANGEREUSES AN POINT DE VUE SECURITE  
NUTILISER QUE CELLS DECRITES  
WITH THE DIGITAL TESTER WHEN THE COLOR BROADCAST  
WAS RECEIVED IN GOOD CONDITION AND PICTURE IS NORMAL.  
DANS LA NOMENCLATURE DES PIECES  
A
B
C
D
E
F
G
H
G-9  
G-10  
WAVEFORMS  
MICON/TUNER  
1V 20µs/div  
11  
1 200mV 5ms/div  
6
0.5V 20µs/div  
1V 20µs/div  
12  
200mV 20µs/div  
7
2
0.5V 20µs/div  
13 1V 20µs/div  
3
20V 20µs/div  
8
200mV 20µs/div  
DEFLECTION/CRT  
200mV 5ms/div  
0.5V 5ms/div  
14  
4
9 200mV 20µs/div  
CHROMA  
15 20V 20µs/div  
0.5V 5ms/div  
10  
5
0.5V 2ms/div  
NOTE: The following waveforms were measured at the point of the corresponding  
balloon number in the schematic diagram.  
H-1  
WAVEFORMS  
16 2V 20µs/div  
21 50V 20µs/div  
22 50V 20µs/div  
200V 20µs/div  
17  
SOUND  
23  
18 10V 5ms/div  
0.5V 1ms/div  
19  
24 1V 1ms/div  
10V 5ms/div  
50V 20µs/div  
20  
NOTE: The following waveforms were measured at the point of the corresponding  
balloon number in the schematic diagram.  
H-2  
MECHANICAL EXPLODED VIEW  
111  
204  
204  
204  
204  
204  
113  
J801  
119  
205  
204  
204  
110  
116  
205  
105  
119  
PCB110  
114  
(CRT PCB)  
203  
L502  
205  
205  
101  
MS501  
FB401  
202  
102  
202  
103  
115  
V801  
104  
203  
115  
ATC001  
TU001  
112  
203  
PCB010  
(MAIN PCB)  
SP351  
201  
201  
117  
108  
118  
109  
201  
107  
120  
106  
I-1  
MECHANICAL REPLACEMENT PARTS LIST  
REF. NO. PART NO.  
DESCRIPTION  
101  
102  
103  
104  
105  
106  
107  
108  
109  
8995034000 CORD CLIP UL CO.  
---  
---  
---  
HEAT SINK  
HEAT SINK  
METAL SPACER  
741WUA0021 SPRING,EARTH  
701APJA036 CABINET,FRONT  
713WPA0096 GUIDE,REMOCON  
7230006856 SHEET,CAUTION  
735WPA0426 BUTTON ASS'Y  
110  
111  
112  
113  
114  
115  
116  
117  
118  
119  
702APA0086 CABINET,BACK  
722552A004 SHEET,RATING  
723000B179 FILM,DECORATION  
7232020733 SHEET,BRAND  
899HV3T001 HOLDER,ANODE WIRE  
762WPA0009 HOLDER,CRT WIRE  
8994201000 HOLDER,CRT WIRE  
7220001109 SHEET,HWC  
7240001041 SHEET,CSA WARNING  
---  
COATING CLIP  
120  
A3I062G720 CABINET,FRONT ASS'Y  
201  
202  
203  
204  
205  
8110630A04 SCREW,TAP TITE (P)  
8117D30A04 SCREW,TAPPING (B0)  
8109630802 SCREW,TAP TITE (B)  
8117540B04 SCREW,TAPPING (B0)  
8111J50D04 SCREW,TAPPING (A)  
BRAZIER  
WH8 BRAZIER 3x10  
BRAZIER  
TRUSS  
GW22  
3x10  
3x8  
4x20  
5x40  
---  
---  
---  
---  
---  
---  
J3I06201  
JB5U0100 POLYBAG  
792AHA0073 PACKAGE,TOP  
792AHA0074 PACKAGE,BOTTOM  
791AHA0021 FILM BAG  
INSTRUCTION BOOK  
793ACDA087 GIFT BOX  
J1-1  
ELECTRICAL REPLACEMENT PARTS LIST  
REF. NO. PART NO.  
DESCRIPTION  
RESISTORS  
REF. NO. PART NO.  
DESCRIPTION  
DIODES  
R135  
R177  
R401  
R404  
R405  
R406  
R407  
R408  
R409  
R417  
R418  
R424  
R428  
R429  
R430  
R443  
R448  
R501  
R502  
R506  
R507  
R509  
R515  
R640  
R647  
R655  
R803  
R805  
R807  
R001T6272J RC  
2.7K OHM 1/6W  
D604  
D605  
D607  
D608  
D609  
D610  
D611  
D612  
D614  
D615  
D616  
D617  
D1VT001330 DIODE, SILICON  
D2WT011E10 DIODE, SILICON  
D1VT001330 DIODE, SILICON  
D9201150B1 DIODE, ZENER  
D2WT0EM1C0 DIODE, SILICON  
D97U01201B DIODE, ZENER  
D97U01201B DIODE, ZENER  
D97U01201B DIODE, ZENER  
D97U06R21B DIODE, ZENER  
D97U06R21B DIODE, ZENER  
D97U06R21B DIODE, ZENER  
D2WT011E10 DIODE, SILICON  
ICS  
I56F07044A IC  
A3I051G015 IC  
I0FSP75230 IC  
I03TD80410 IC  
I1KA97805A IC  
I2B4901100 IC  
I06FC12030 IC  
1SS133T-77  
11E1-EIC  
1SS133T-77  
RD15FB  
EM1C-EIC  
MTZJ12B T-77  
MTZJ12B T-77  
MTZJ12B T-77  
MTZJ6.2B T-77  
MTZJ6.2B T-77  
MTZJ6.2B T-77  
11E1-EIC  
!
!
!
!
!
!
!
!
R5W2CF122J R, CEMENT  
R4X5T4104F R, METAL  
R002T4272J RC  
R4X5T4183F R, METAL  
R903N8332J RC  
1.2K OHM 10W  
100K OHM 1/4W  
2.7K OHM 1/4W  
18K OHM 1/4W  
3.3K OHM 1/8W  
R65581010J R, FUSE  
R4X5T6183F R, METAL  
R4X5T6622F R, METAL  
R4X5T6113F R, METAL  
R4X5T6223F R, METAL  
R4X5T6123F R, METAL  
R3X28A8R2J R, METAL  
R6558A1R8J R, FUSE  
R00106104J RC  
R6558A4R7J R, FUSE  
R5X2CD332J R, CEMENT  
R21202105K R, SOLID  
R5X2CE1R2J R, CEMENT  
R5W2CH181J R, CEMENT  
R655U4470J R, FUSE  
R4X5T6183F R, METAL  
R3X28B1R5J R, METAL  
R5X2CF222J R, CEMENT  
R00106182J RC  
1
OHM 1W  
18K OHM 1/6W  
6.2K OHM 1/6W  
11K OHM 1/6W  
22K OHM 1/6W  
12K OHM 1/6W  
8.2 OHM 2W  
1.8 OHM 2W  
100K OHM 1/6W  
4.7 OHM 2W  
3.3K OHM 5W  
1M OHM 1/2W  
1.2 OHM 7W  
180 OHM 20W  
47 OHM 1/4W  
18K OHM 1/6W  
1.5 OHM 3W  
2.2K OHM 10W  
1.8K OHM 1/6W  
2.2K OHM 10W  
12K OHM 2W  
12K OHM 2W  
12K OHM 2W  
!
!
!
IC101  
IC199  
IC351  
IC401  
IC402  
IC501  
IC601  
OEC7044A  
S-24C02BDP-1A  
AN7523  
!
!
!
!
!
!
LA78041  
KIA7805API  
STR30110  
M61203BFP  
!
TRANSISTORS  
!
!
!
!
Q101  
Q351  
Q401  
Q402  
Q403  
Q501  
Q603  
Q606  
Q608  
Q801  
Q802  
Q803  
TNYTJ03001 COMPOUND TRANSISTOR  
TC5T018154 TRANSISTOR, SILICON  
TDUU024990 TRANSISTOR, SILICON  
TC3Q026210 TRANSISTOR, SILICON  
TPYTD03001 COMPOUND TRANSISTOR  
TC5T018154 TRANSISTOR, SILICON  
TD3T007340 TRANSISTOR, SILICON  
TD3T007340 TRANSISTOR, SILICON  
TA5T010154 TRANSISTOR, SILICON  
TC3Q040750 TRANSISTOR, SILICON  
TC3Q040750 TRANSISTOR, SILICON  
TC3Q040750 TRANSISTOR, SILICON  
COILS &TRANSFORMERS  
021LA63R3K COIL  
DTC114TSTP  
2SC1815Y(TPE2)  
2SD2499(LBOEC1)  
2SC2621(D,E)-RAC  
DTA144ESTP  
2SC1815Y(TPE2)  
2SD734(E,F)-AA  
2SD734(E,F)-AA  
2SA1015Y(TPE2)  
2SC4075-YAC  
!
!
!
!
!
!
R5X2CF222J R, CEMENT  
R3X18A123J R, METAL OXIDE  
R3X18A123J R, METAL OXIDE  
R3X18A123J R, METAL OXIDE  
CAPACITORS  
C132  
C351  
C404  
C405  
C412  
C414  
C416  
C418  
C433  
C434  
C437  
C443  
C444  
C446  
C448  
C501  
C506  
C507  
C519  
C624  
C646  
C699  
E5EZF3222M CE  
E02LF1332M CE  
E02LT1471M CE  
E02LT2471M CE  
E02LT1471M CE  
E5EZT4101M CE  
P3N1F2183J CPP  
E5EZF3222M CE  
E02LT4471M CE  
E02LT8220M CE  
P411F3564J CMPP  
P414F9103H CMPP  
C01BBP7H2K CC  
E5EZTB010M CE  
E02LT8220M CE  
P2122B224M CMP  
E52SFC681M CE  
E5EZFB101M CE  
E5EZTB100M CE  
E02L01222M CE  
E02LF3222M CE  
CHGTY0214M CC  
2200 UF 25V  
3300 UF 10V  
470 UF 10V  
470 UF 16V  
470 UF 10V  
!
!
!
2SC4075-YAC  
2SC4075-YAC  
!
!
!
!
L101  
L406  
L501  
L502  
L601  
L603  
L605  
L607  
L801  
L802  
T401  
3.3 UH  
18 UH  
9-000074  
8R250009  
1.2 UH  
10 UH  
100 UF 35V  
021U6D180K COIL  
0.018 UF 200V  
2200 UF 25V  
470 UF 35V  
22 UF 100V  
0.56 UF 250V ECWF  
0.01 UF 1.6KV ECWH  
220 PF 2KV BP  
1UF 160V  
22 UF 100V  
0.22 UF 250V ECQUL  
680 UF 200V  
100 UF 160V  
10UF 160V  
2200 UF 10V  
2200 UF 25V  
0.01 UF 16V Y  
!
!
029K000074 COIL, LINE FILTER  
028R250009 COIL, DEGAUSS  
0216731R2K COIL  
021673100K COIL  
0216731R0J COIL  
021LA6150K COIL  
02167D101K COIL  
02A6A8A0A1 CORE, FERRITE  
045013001J TRANS, HORIZONTAL DRIVE  
JACK  
!
!
!
1
UH  
!
!
!
!
!
!
!
!
15 UH  
100 UH  
HF57T18.5*10*10  
5013001  
!
J801  
066C130015 SOCKET, CRT  
CVT3275-5102  
SWITCHES  
SW101  
SW102  
SW103  
SW104  
SW105  
0504201T31 SWITCH, TACT  
0504101T34 SWITCH, TACT  
0504201T31 SWITCH, TACT  
0504101T34 SWITCH, TACT  
0504201T31 SWITCH, TACT  
0504101T34 SWITCH, TACT  
0504201T31 SWITCH, TACT  
0504101T34 SWITCH, TACT  
0504201T31 SWITCH, TACT  
0504101T34 SWITCH, TACT  
P.C.BOARD ASSEMBLIES  
A3I058G01A PCB ASS'Y  
A3I057G11A PCB ASS'Y  
MISCELLANEOUS  
0632400008 ANT, UNIT  
120R614909 CORD, AC  
1207614909 CORD, AC  
068M82025A CORD, CONNECTOR  
122E054401 CORD, JUMPER  
122E044101 CORD, JUMPER  
1022T45R72 FILTER, SAW  
1011T4R504 FILTER, CERAMIC  
1011T4R517 FILTER, CERAMIC  
069W120019 CONNECTOR PCB SIDE  
069W340018 CONNECTOR PCB SIDE  
0697320039 CORD, UX CONNECTOR  
069W420029 CONNECTOR PCB SIDE  
0697260650 CONNECTOR PCB SIDE  
069W320018 CONNECTOR PCB SIDE  
SKHVBED010  
EVQ21505R  
SKHVBED010  
EVQ21505R  
SKHVBED010  
EVQ21505R  
SKHVBED010  
EVQ21505R  
SKHVBED010  
EVQ21505R  
or  
or  
or  
or  
or  
DIODES  
D001  
D101  
D103  
D104  
D125  
D126  
D127  
D401  
D402  
D403  
D404  
D405  
D407  
D408  
D410  
D411  
D422  
D501  
D502  
D503  
D504  
D601  
D602  
D603  
D94TA30013 DIODE, ZENER  
D97U06R81B DIODE, ZENER  
D97U06R81B DIODE, ZENER  
D97U06R81B DIODE, ZENER  
D1VT001330 DIODE, SILICON  
D2WT0EM1C0 DIODE, SILICON  
D2WT011E10 DIODE, SILICON  
D94TA27011 DIODE, ZENER  
D94TA11B11 DIODE, ZENER  
D2WT011E10 DIODE, SILICON  
D2WTAU02A0 DIODE, SILICON  
D97U06R21B DIODE, ZENER  
D2WTAU02A0 DIODE, SILICON  
D2WTAU02A0 DIODE, SILICON  
D2WTAU02A0 DIODE, SILICON  
D2WTAU02A0 DIODE, SILICON  
D2WTAU02A0 DIODE, SILICON  
D2WTRM11C0 DOIDE, SILICON  
D2WTRM11C0 DOIDE, SILICON  
D2WTRM11C0 DOIDE, SILICON  
D2WTRM11C0 DOIDE, SILICON  
D1VT001330 DIODE, SILICON  
D97U08R21B DIODE, ZENER  
D1VT001330 DIODE, SILICON  
HZ30-3L TD  
MTZJ6.8B T-77  
MTZJ6.8B T-77  
MTZJ6.8B T-77  
1SS133T-77  
EM1C-EIC  
!
11E1-EIC  
PCB010  
PCB110  
TMX456A  
TCX315A  
!
!
HZ27-1L TD  
HZ11B1L TD  
11E1-EIC  
!
!
ATC001  
CD501  
NXC0032-010010  
0R614909  
7614909  
!
AU02A-EIC  
MTZJ6.2B T-77  
AU02A-EIC  
AU02A-EIC  
AU02A-EIC  
AU02A-EIC  
AU02A-EIC  
RM11C-EIC  
RM11C-EIC  
RM11C-EIC  
RM11C-EIC  
1SS133T-77  
MTZJ8.2B T-77  
1SS133T-77  
or  
!
!
!
!
!
!
!
!
!
CD801  
CD802  
CD803  
CF601  
CF603  
CF604  
CP351  
CP401  
CP501  
CP502  
CP601  
CP801  
8M82025A  
122E054401  
122E044101  
SAF45MFY220ZR  
EFCT4R5YS5A  
EFCT4R5MW5  
TID-X02P-B2  
TS-80P-04-V1  
THL-P03P-B1  
TV-50P-02-A1  
TKC-M06X-A1  
TS-80P-02-V1  
!
!
!
J2-1  
ELECTRICAL REPLACEMENT PARTS LIST  
REF. NO. PART NO.  
DESCRIPTION  
MISCELLANEOUS  
CP806  
069W010010 CONNECTOR PCB SIDE  
067R005019 WIRE HOLDER  
067R005019 WIRE HOLDER  
067R104019 WIRE HOLDER  
067R104019 WIRE HOLDER  
027M062505 DY  
005P-2100  
51048-0510  
51048-0510  
51052-0400  
51052-0400  
7M062505  
23706.3  
CP802A  
CP802B  
CP803A  
CP803B  
DY801  
F501  
!
!
!
081PA6R302 FUSE  
FB401  
FH501  
FH502  
K001  
K002  
K003  
043225010F TRANSFORMER, FLYBACK  
06710T0006 HOLDER, FUSE  
06710T0006 HOLDER, FUSE  
129A000010 WEDGE  
129A000010 WEDGE  
129A000010 WEDGE  
3225010F  
EYF-52BC  
EYF-52BC  
8115529  
8115529  
8115529  
!
!
!
MG801  
MS501  
OS101  
RY101  
SP351  
TH501  
TM101  
TU001  
V801  
026A062704 MAGNET, CONVERGENCE  
128B000018 SHEET  
077Q014003 REMOTE RECEIVER  
0560V20115 RELAY  
29MMSTAR  
23MICA  
PIC-28143SY-2  
ALKS321  
SA04A05AWA  
PTAD14K2-3R0Q141  
R25-1127  
NJH3021U268  
A63AHC26X  
8MHz  
!
!
!
070C533016 SPEAKER  
DF40A3R0Q0 DEGAUSS, ELEMENT  
076R074180 TRANSMITTER  
0145W00049 TUNER, VHF-UHF  
0984250502 COLOR, PICTURE TUBE  
1002T00801 CERAMIC OSILLATOR  
100CT3R505 CRYSTAL HC-49/C  
!
!
X101  
X602  
3.579545MHz  
RESISTOR  
RC................... CARBON RESISTOR  
CAPACITORS  
CC................... CERAMIC CAPACITOR  
CE................... ALUMI ELECTROLYTIC CAPACITOR  
CP................... POLYESTER CAPACITOR  
CPP................. POLYPROPYLENE CAPACITOR  
CPL.................. PLASTIC CAPACITOR  
CMP................. METAL POLYESTER CAPACITOR  
CMPL............... METAL PLASTIC CAPACITOR  
CMPP.............. METAL POLYPROPYLENE CAPACITOR  
J2-2  
M3I0-62G  
A063519  
SPEC.NO.  
O/R NO.  

HP Hewlett Packard Hewlett Packard Computer Monitor S1922 User Manual
GE 681131692144 User Manual
GE 27911 User Manual
Electrolux 260728 User Manual
Dell Computer Monitor E1909W User Manual
Cypress CY7C1548V18 User Manual
Cypress CY7C1513V18 User Manual
Computer Tech Link CTL 5fln User Manual
Asus Computer Hardware B85MG User Manual
Asus Computer Hardware AB P 2600 User Manual