Dell Computer Monitor 2709W User Manual

Dell™ 2709W Flat Panel Monitor User's Guide  
About Your Monitor  
Solving Problems  
Setting Up the Monitor  
Appendix  
Operating the Monitor  
Notes, Notices, and Cautions  
Throughout this guide, blocks of text may be accompanied by an icon and printed in bold type or in italic type. These blocks are notes, notices, and cautions,  
and they are used as follows:  
NOTE: A NOTE indicates important information that helps you make better use of your computer.  
NOTICE: A NOTICE indicates either potential damage to hardware or loss of data and tells you how to avoid  
the problem.  
CAUTION: A CAUTION indicates the potential for property damage, personal injury, or death.  
Some warnings may appear in alternate formats and may be unaccompanied by an icon. In such cases, the specific presentation of the caution is mandated by  
regulatory authority.  
Information in this document is subject to change without notice.  
© 2008 Dell™ Inc. All rights reserved.  
Reproduction in any manner whatsoever without the written permission of Dell Inc. is strictly forbidden.  
Trademarks used in this text: Dell, the DELL logo are trademarks of Dell Inc; Microsoft and Windows either registered trademarks or trademarks of Microsoft Corporation in the  
United States and/or other countries. ENERGY STAR is a registered trademark of the U.S. Environmental Protection Agency. As an ENERGY STAR partner, Dell Inc. has determined  
that this product meets the ENERGY STAR guidelines for energy efficiency.  
Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks and names or their products. Dell Inc. disclaims any  
proprietary interest in trademarks and trade names other than its own.  
Model 2709Wb  
July 2008  
Rev. A02  
 
3
Input Source Select  
4
5
6
OSD menu select  
EXIT  
Power button (with power light indicator)  
Back View  
Back view  
Back View with monitor stand  
Label  
Description/Use  
VESA mounting holes (100mm)  
(Behind attached VESA Plate)  
1
2
To mount the monitor.  
Connectors label  
To indicate the positions and types of connectors.  
3
4
5
6
7
8
Service Tag label  
To contact Dell for express service.  
To help secure your monitor.  
Security lock slot  
Dell Soundbar mounting brackets  
Barcode serial number label  
Regulatory rating label  
Cable management slot  
To attach the optional Dell Soundbar.  
To contact Dell for technical support.  
Lists the regulatory approvals.  
To organize cables by placing them through the slot.  
Side View  
Right side  
Left side  
Label Description  
1
2
Card reader. See Card Reader Specifications for more information.  
USB downstream ports  
Bottom View  
Bottom view  
Label Description  
1
2
3
4
AC power cord connector  
DC power connector for Dell™ Soundbar  
DisplayPort connector  
HDMI connector  
5
DVI connector-1  
6
DVI connector-2  
7
VGA connector  
8
Composite video connector  
Component video connectors  
Audio out (rear)  
9
10  
11  
12  
13  
14  
Audio out (SUB/CTR)  
Audio out (front)  
USB upstream port  
USB downstream ports  
Monitor Specifications  
The following sections give you information about the various power management modes and pin assignments for various connectors for your monitor.  
Power Management Modes  
If you have VESA's DPMS compliance display card or software installed in your computer, the monitor automatically reduces its power consumption when not in  
use. This is referred to as Power Save Mode. If input from keyboard, mouse or other input devices is detected by the computer, the monitor will automatically  
"wake up". The following table shows the power consumption and signaling of this automatic power-saving feature:  
VESA Modes  
Horizontal  
Sync  
Vertical Sync  
Video  
Power  
Indicator  
Power Consumption  
Normal operation  
Active  
Active  
Active  
Blue  
160 W (maximum)*  
105 W (normal)**  
Active-off mode  
Switch off  
Inactive  
-
Inactive  
-
Blanked  
-
Amber  
Off  
Less than 2 W  
Less than 1 W  
* With Audio and USB  
** Without Audio and USB  
Activate the computer and wake up the monitor to gain access to the OSD.  
NOTE: This monitor is ENERGY STAR®-compliant as well as TCO '03 power management  
compatible.  
NOTE: Zero power consumption in OFF mode can only be achieved by disconnecting the main cable from the  
monitor.  
Pin Assignments  
VGA Connector  
Pin  
Number  
15-pin Side of the  
Connected Signal Cable  
1
2
3
4
5
6
7
Video-Red  
Video-Green  
Video-Blue  
GND  
Self-test  
GND-R  
GND-G  
   
8
GND-B  
9
Computer 5V/3.3V  
GND-sync  
GND  
10  
11  
12  
13  
14  
15  
DDC data  
H-sync  
V-sync  
DDC clock  
DVI Connector  
Pin  
Number  
24-pin Side of the Connected Signal  
Cable  
1
TMDS RX2-  
TMDS RX2+  
TMDS Ground  
Floating  
2
3
4
5
Floating  
6
DDC Clock  
DDC Data  
7
8
Floating  
9
TMDS RX1-  
TMDS RX1+  
TMDS Ground  
Floating  
10  
11  
12  
13  
14  
15  
16  
17  
18  
19  
20  
21  
22  
23  
24  
Floating  
+5V/+3.3V power  
Self test  
Hot Plug Detect  
TMDS RX0-  
TMDS RX0+  
TMDS Ground  
Floating  
Floating  
TMDS Ground  
TMDS Clock+  
TMDS Clock-  
Composite Video Connector  
Luma composite chroma  
Component Video Connector  
Pin Number  
3-pin Side of the Connected Signal Cable (Cable not  
included)  
1
2
3
Y (Luminance signal)  
Pb (Color differential signal)  
Pr (Color differential signal)  
DisplayPort Connector  
Pin  
Number  
20-pin Side of the Connected Signal  
Cable  
1
ML0(p)  
GND  
2
3
ML0(n)  
ML1(p)  
GND  
4
5
6
ML1(n)  
ML2(p)  
GND  
7
8
9
ML2(n)  
ML3(p)  
GND  
10  
11  
12  
13  
14  
15  
16  
17  
18  
19  
20  
ML3(n)  
GND  
GND  
AUX(p)  
GND  
AUX(n)  
HPD  
Re-PWR  
PWR  
HDMI Connector  
Pin  
Number  
19-pin Side of the Connected Signal  
Cable  
1
TMDS DATA 2+  
TMDS DATA 2 SHIELD  
TMDS DATA 2-  
TMDS DATA 1+  
TMDS DATA 1 SHIELD  
TMDS DATA 1-  
TMDS DATA 0+  
TMDS DATA 0 SHIELD  
TMDS DATA 0-  
TMDS CLOCK  
2
3
4
5
6
7
8
9
10  
11  
12  
13  
14  
15  
16  
17  
18  
19  
TMDS CLOCK SHIELD  
TMDS CLOCK-  
Floating  
Floating  
DDC CLOCK (SDA)  
DDC DATA (SDA)  
GROUND  
+5V POWER  
HOT PLUG DETECT  
Flat Panel Specifications  
Screen type  
Active matrix - TFT LCD  
Screen dimensions  
Preset display area:  
27 inches (27-inch diagonal viewable image size)  
581.76 mm (22.9 inches)  
363.6 mm (14.30 inches)  
Horizontal  
Vertical  
Pixel pitch  
0.303 mm  
Viewing angle  
Luminance output  
Contrast ratio  
Faceplate coating  
Backlight  
178° (Vertical) typical, 178° (Horizontal) typical  
400 cd/m ²(typ)  
1300:1 (typ), 3000:1 (typ, Dynamic Contrast on)  
Antiglare with hard-coating 3H  
8 CCFL U-type system  
Response Time  
Color Gamut  
6ms panel typical (Grey to Grey))/16ms typical (Black to White)  
110%* typical  
* 2709W Color Gamut (Typical) is based on CIE1976 (110%) and CIE1931 (102%) .  
Resolution  
Horizontal scan range  
Vertical scan range  
30 kHz to 81 kHz (automatic)  
56 Hz to 76 Hz  
Optimal preset resolution  
Highest preset resolution  
1920 x 1200 at 60 Hz  
1920 x 1200 at 60 Hz  
Video Supported Modes  
Video display capabilities (DVI playback)  
480p/576p/720p/1080p (Supports HDCP)  
Video display capabilities (Composite playback) NTSC/PAL  
Video display capabilities (HDMI playback)  
480i/480p/576i/576p/720p/1080i/1080p  
Video display capabilities (Component playback) 480i/480p/576i/576p/720p/1080i/1080p  
Preset Display Modes  
The following table lists the preset modes for which Dell guarantees image size and centering:  
Display Mode  
Horizontal  
Frequency (kHz)  
Vertical  
Frequency (Hz)  
Pixel Clock  
(MHz)  
Sync Polarity  
(Horizontal/Vertical)  
VGA, 720 x 400  
31.5  
31.5  
37.5  
37.9  
46.9  
48.4  
60.0  
67.5  
64.0  
80.0  
75.0  
74.5  
70.1  
59.9  
75.0  
60.3  
75.0  
60.0  
75.0  
75.0  
60.0  
75.0  
60.0  
60.0  
28.3  
25.2  
-/+  
-/-  
VGA, 640 x 480  
VESA, 640 x 480  
VESA, 800 x 600  
VESA, 800 x 600  
VESA, 1024 x 768  
VESA, 1024 x 768  
VESA, 1152 x 864  
VESA, 1280 x 1024  
VESA, 1280 x 1024  
VESA, 1600 x 1200  
VESA, 1920 x 1200  
31.5  
-/-  
40.0  
+/+  
+/+  
-/-  
49.5  
65.0  
78.8  
+/+  
+/+  
+/+  
+/+  
+/+  
+/-  
108.0  
108.0  
135.0  
162.0  
154.0  
Electrical  
The following table lists the electrical specification:  
Video input signals  
Analog RGB, 0.7 Volts +/-5%, 75 ohm input impedance  
Digital DVI-D TMDS, 600mV for each differential line, 50 ohm input  
impedance  
HDMI, 600mV for each differential line, 100 ohm input impedance  
per differential pair  
DisplayPort, 600mV for each differential line, 100 ohm input  
impedance per differential pair  
Composite, 1 volt(p-p), 75 ohm input impedance  
Component: Y, Pb, Pr are all 0.5~1volt(p-p), 75 ohm input  
impedance  
Synchronization input signals  
separate horizontal and vertical,  
3.3V CMOS or 5V TTL level, positive or negative sync.  
SOG (Sync on green)  
AC input voltage/frequency/current  
Inrush current  
100 to 240 VAC/50 or 60 Hz + 3 Hz/2.0A (Max.)  
120V: 40A (Max.)  
240V: 80A (Max.)  
Physical Characteristics  
The following table lists the physical characteristics:  
Connector type  
l
l
l
l
l
l
D-sub: blue connector  
DVI-D: white connector  
DisplayPort: black connector  
Composite  
Component  
HDMI  
Signal cable type  
l
l
l
D-sub: Detachable, Analog, 15pin, shipped attached to the  
monitor  
DVI-D: Detachable, Digital, 24pin, shipped detached from  
the monitor  
DisplayPort: Detachable, Digital, 20pin, shipped detached  
from the monitor  
Composite  
Component  
HDMI  
l
l
l
NOTE: The composite, component and HDMI cables are  
not included with the monitor.  
Dimensions (with stand)  
Height (Compressed)  
451.9 mm (17.79 inches)  
541.9 mm (21.33 inches)  
632.1 mm (24.89 inches)  
200.0 mm (7.87 inches)  
Height (Extended)  
Width  
Depth  
Dimensions (without stand)  
Height  
413.9 mm (16.30 inches)  
632.1 mm (24.89 inches)  
88.4 mm (3.48 inches)  
Width  
Depth  
Stand Dimensions  
Height (Compressed)  
Height (Extended)  
Width  
306 mm (12.05 inches)  
396 mm (15.59 inches)  
320 mm (12.60 inches)  
200.0 mm (7.87 inches)  
Depth  
Weight  
Weight with packaging  
14.3 kg (31.53 lb)  
Weight with stand assembly and  
cables  
12.2 kg (26.90 lb)  
Weight without stand assembly  
(For wall mount or VESA mount  
considerations - no cables)  
8.3 kg (18.30 lb)  
2.7 kg (5.95 lb)  
Weight of stand assembly  
Environmental  
The following table lists the environmental limitation:  
Temperature  
0° to 40°C (32° to 104°F)  
Operating  
Storage: -20° to 60°C (-4° to 140°F)  
Shipping: -20° to 60°C(-4° to 140°F)  
Nonoperating  
Humidity  
10% to 80% (noncondensing)  
Operating  
Storage: 5% to 90% (noncondensing)  
Shipping: 5% to 90%(noncondensing)  
Nonoperating  
Altitude  
3,657.6 m (12,000 ft) max  
12,192 m (40,000 ft) max  
Operating  
Nonoperating  
Thermal dissipation  
375 BTU/hour (maximum)  
195 BTU/hour (typical)  
Universal Serial Bus (USB) Interface  
This monitor supports High-Speed Certified USB 2.0 interface.  
Transfer speed  
Data Rate  
Power  
Consumption  
High speed  
Full speed  
Low speed  
480 Mbps  
12 Mbps  
1.5 Mbps  
2.5W (Max., each port)  
2.5W (Max., each port)  
2.5W (Max., each port)  
USB Upstream Connector  
Pin Number  
4-pin Side of the connector  
1
2
3
4
DMU  
VCC  
DPU  
GND  
USB Downstream Connector  
Pin Number  
4-Pin Side of the Signal Cable  
1
2
3
4
VCC  
DMD  
DPD  
GND  
USB Ports  
l
l
1 upstream - rear  
4 downstream - 2 on rear; 2 on left side  
 
NOTE: The monitor's 2.0 USB interface functions only if the computer is USB 2.0 compatible.  
NOTE: The monitor's USB interface works only when the monitor is on or in power save mode. If you switch  
the monitor off and then switch it on, the attached peripherals may take a few seconds to resume normal  
functionality.  
Card Reader Specifications  
Overview  
l
l
l
l
The Flash Memory Card Reader is a USB storage device that allows users to read and write information from and into the memory card.  
The Flash Memory Card Reader is automatically recognized by Microsoft® Windows® 2000, Windows® XP and Windows Vista®.  
Once installed and recognized, each separate memory card (slot) appears as a separate drive/drive letter.  
All standard file operations (copy, delete, drag-and-drop, etc.) can be performed with this drive.  
Features  
The Flash Memory Card Reader has the following features:  
l
l
l
l
l
Supports Microsoft® Windows® 2000, Windows® XP and Windows Vista® operating systems  
No Microsoft® Windows® 9X support from Dell  
Mass Storage Class device (No drivers are required under Microsoft® Windows® 2000, Windows® XP and Windows Vista®)  
USB-IF certification  
Supports various memory card media  
The following table lists the memory cards supported:  
Slot Number  
Flash memory cards type  
1
2
Compact Flash type I/II Card (CF I/II)/CF form factor ATA hard drives to USB 2.0 bus  
xD-Picture Card  
Memory Stick Card (MS)/High Speed Memory Stick (HSMS)/Memory Stick Pro Card (MS  
PRO)/Memory Stick Duo (with Adapter)  
Secure Digital Card (SD)/Mini Secure Digital (with Adapter)/TransFlash Card (with  
Adapter)  
MultiMedia Card (MMC)/Reduced Size MultiMedia Card (with Adapter)  
Maximum Card Capacity Supported by the 2709W card reader  
Card type  
Support Specification  
Memory Card Support Maximum  
Spec Version Capacity by Spec  
USB2602-NU-05  
(For  
2709W)  
CF  
Compact Flash Specification  
2.0  
128GB  
Supported  
Supported  
Supported  
Supported  
MS  
Memory Stick Standard Format Specification  
Memory Stick Pro Standard Format Specifications  
Memory Stick Duo Standard Format Specifications  
SmartMedia™ Electrical Specification  
1.40-00  
1.01-01  
1.10-00  
1.40  
128MB  
MSPRO  
MSDuo  
32GB  
128MB/32GB  
SM  
SmartMediaPhysical Format Specifications  
1.40  
256MB  
Supported  
 
SmartMediaLogical Format Specifications  
xD Picture Card Specification  
1.30  
1.2  
xD  
2GB  
Supported  
Supported  
Supported  
SD  
SD Memory Card Specifications  
2.0  
32GB  
32GB  
MMC  
MultiMedia Card System Specification  
4.2  
NOTE: MSPRO includes MSPRO Duo and MS Micro.  
NOTE: xD includes TypeM and TypeH.  
NOTE: SD includes HS-SD, MiniSD and SD Micro. SD v2.0 spec includes SDHC.  
NOTE: MMC includes MMCPlus, RS-MMC, MMC Mobile and MMC micro.  
General  
Connection type  
USB 2.0 High Speed Device (USB Full Speed Device compatible)  
Supported OS  
Microsoft® Windows® 2000, Windows® XP and Windows Vista®  
Performance  
Transfer Speed  
Read: 480 Mb/s (max.)  
Write: 480 Mb/s (max.)  
Plug and Play Capability  
You can install the monitor in any Plug and Play-compatible system. The monitor automatically provides the computer system with its Extended Display  
Identification Data (EDID) using Display Data Channel (DDC) protocols so the system can configure itself and optimize the monitor settings. If required, the  
user can select different settings, but in most cases monitor installation is automatic.  
Maintenance Guidelines  
Caring for Your Monitor  
CAUTION: Read and follow the Safety Instructions before cleaning the monitor.  
CAUTION: Before cleaning the monitor, unplug the monitor from the electrical  
outlet.  
For best practices, follow the instructions in the list below while unpacking, cleaning, or handling your monitor:  
l
To clean your antistatic screen, lightly dampen a soft, clean cloth with water. If possible, use a special screen-cleaning tissue or solution suitable for the  
antistatic coating. Do not use benzene, thinner, ammonia, abrasive cleaners, or compressed air.  
l
l
l
Use a lightly-dampened, warm cloth to clean the plastics. Avoid using detergent of any kind as some detergents leave a milky film on the plastics.  
If you notice a white powder when you unpack your monitor, wipe it off with a cloth.  
Handle your monitor with care as dark-colored monitors may scratch and show white scuff marks more than lighter-colored monitors.  
     
Appendix  
Dell™ 2709W Flat Panel Monitor User's Guide  
CAUTION: Safety Instructions  
CAUTION: Use of controls, adjustments, or procedures other than those specified in this documentation may result in exposure to shock,  
electrical hazards, and/or mechanical hazards.  
For information on safety instructions, see the Safety Information.  
FCC Notice (U.S. Only) and Other Regulatory Information  
For FCC notices and other regulatory information, see the regulatory compliance website located at www.dell.com\regulatory_compliance.  
Contacting Dell  
To contact Dell electronically, you can access the following websites and by phone:  
l
l
For support through the web, go to support.dell.com.  
For customers in the United States, call 800-WWW-DELL (800-999-3355).  
NOTE: If you do not have an active Internet connection, you can find contact information on your purchase invoice, packing slip, bill, or Dell product  
catalog.  
Dell provides several online and telephone-based support and service options. Availability varies by country and product, and some services may not be  
available in your area. To contact Dell for sales, technical support, or customer service issues:  
1. Visit support.dell.com.  
2. Verify your country or region in the Choose A Country/Region drop-down menu at the bottom of the page.  
3. Click Contact Us on the left side of the page.  
4. Select the appropriate service or support link based on your need.  
5. Choose the method of contacting Dell that is convenient for you.  
     
Setting Up Your Monitor  
Dell™ 2709W Flat Panel Monitor  
If you have a Delldesktop or a Dellportable computer with internet access  
1. Go to http://support.dell.com, enter your service tag, and download the latest driver for your graphics card.  
2. After installing the drivers for your Graphics Adapter, attempt to set the resolution to 1920x1200 again.  
NOTE: If you are unable to set the resolution to 1920x1200, please contact Dell™ to inquire about a Graphics Adapter that supports these resolutions.  
 
Setting Up Your Monitor  
Dell™ 2709W Flat Panel Monitor  
If you have non Delldesktop, portable computer, or graphic card  
1. Right-click on the desktop and click Properties.  
2. Select the Settings tab.  
3. Select Advanced.  
4. Identify your graphics controller supplier from the description at the top of the window (e.g. NVIDIA, ATI, Intel etc.).  
5. Please refer to the graphic card provider website for updated driver (for example, http://www.ATI.com OR http://www.NVIDIA.com ).  
6. After installing the drivers for your Graphics Adapter, attempt to set the resolution to 1920x1200 again.  
NOTE: If you are unable to set the resolution to 1920x1200, please contact the manufacturer of your computer or consider purchasing a graphics adapter  
that will support the video resolution of 1920x1200.  
 
Operating the Monitor  
Dell™ 2709W Flat Panel Monitor User's Guide  
Using the Front Panel  
Use the buttons on the front of the monitor to adjust the image settings.  
1-3  
1
Shortcut keys  
Use this key for direct access to the control menu that you define in the personalize menu.  
*The default settings are Preset Modes Select, Brightness/Contrast Select and Input Source Select.  
Use this button for different displays on your monitor.  
Preset Modes Select  
Brightness/Contrast  
Input Source Select  
2
Use this button for direct access to the "Brightness/Contrast" control menu.  
3
Use Input Source Select button to select between different video signals that may be connected to your monitor.  
l
l
l
l
l
l
l
VGA input  
DVI-D 1 input  
DVI-D 2 input  
DisplayPort input  
HDMI input  
Component video input  
Composite video input  
Displays the source selection bar. Press  
you want.  
and  
buttons to move between the setting options and press  
to select the in  
 
If either VGA or DVI-D input is selected and both VGA and DVI-D cables are not connected, a floating dialog box as shown below  
or  
If either Composite, or Component input is selected and the cables are not connected or the video source is turned off, the scr  
not have an image. If any button is pressed (except power button), the monitor displays the following message:  
or  
4
5
Use this key to open the on-screen display (OSD). See Using the OSD Menu.  
Use this key to exit the OSD menu.  
OSD Menu  
Exit  
6
Use the power button to turn the monitor on and off.  
Power button  
(with power light  
indicator)  
The blue light indicates the monitor is on and fully functional. An amber light indicates power save mode.  
Using the OSD Menu  
NOTE: If you change the settings and then either proceed to another menu, or exit the OSD menu, the monitor  
automatically saves the changes. The changes are also saved if you change the settings and then wait for the  
OSD menu to disappear.  
1. Press  
to launch the OSD menu and display the main menu.  
Main Menu for Analog (VGA) Input  
 
Or  
Main Menu for non Analog (non VGA) Input  
NOTE: Auto Adjust is only available when you are using the analog (VGA) connector.  
2.Press the  
and  
buttons to move between the setting options. As you move from one icon to another, the option name is highlighted. See the table  
for a complete list of all the options available for the monitor.  
3.Press the  
button once to activate the highlighted option.  
4.Press  
5. Press  
and  
button to select the desired parameter.  
to enter the slide bar and then use the  
and  
buttons, according to the indicators on the menu, to make your changes.  
6.Press  
return to the main menu or  
to exit the OSD menu.  
Icon  
Menu and Submenus  
Brightness/Contrast  
Description  
Allows you to adjust the brightness and contrast.  
Brightness  
Contrast  
Brightness adjusts the luminance of the backlight.  
Press the button to increase brightness and Press the  
button to decrease brightness (min 0 ~ max 100).  
Adjust Brightness first, and then adjust Contrast only if further adjustment is necessary.  
Press the button to increase contrast and Press the button to decrease contrast (min 0 ~ max 100).  
The Contrast function adjusts the degree of difference between the darkest and lightest areas on the monitor screen.  
Back  
Press  
to go back to the main menu.  
Auto Adjust  
Even though your computer recognizes your monitor on startup, the Auto Adjustment function optimizes the display setting  
NOTE: In most cases, Auto Adjust produces the best image for your configuration. This option is only available when you a  
connector.  
Input  
The Input Source menu is to select between different video signals that may be connected to your monitor.  
Source  
Auto Select  
Scan for Sources. Press  
to scan for available input signals.  
VGA  
Select VGA input when you are using the analog (VGA) connector. Press  
Select DVI-D input when you are using the Digital (DVI) connector. Press  
to select the VGA input source.  
to select the DVI input source.  
DVI-D 1 & 2  
DisplayPort  
HDMI  
Select DisplayPort input when you are using DisplayPort connector. Press  
to select the DisplayPort input source.  
Select HDMI input when you are using HDMI connector. Press  
to select the HDMI input source.  
Component  
Composite  
Back  
Select Component input when you are using component video connector. Press  
Select Composite input when you are using composite video connector. Press  
to select the component input source.  
to select the composite input source.  
Press  
to go back to the main menu.  
Color Settings  
Allows you to set the image mode and color format.  
Image mode submenu for VGA/DVI-D input  
NOTE: Image modes are different between the VGA/DVI-D and Video inputs  
Allows you to set the color format to:  
Input Color Format  
PC RGB-Suitable for normal PC graphics display over DVI  
HD YPbPr-Suitable for HD video playback over DVI.  
Gamma  
Allows you to set the color mode to PC or Mac.  
Mode Select  
Allows you to set the display mode to Graphics or Video. If your computer is connected to your monitor, choose Graphics. If  
Preset modes  
VGA/DVI-D input  
Standard  
Mode suitable for desktop applications.  
Multimedia  
Mode for multimedia applications, eg video playback.  
Game  
Warm  
Mode suitable for gaming applications.  
Select warm mode to obtain a red tint. This color setting is typically used for color-intensive applications (photograph image  
Cool  
Select cool mode to obtain a bluish tint. This color setting is typically used for text based applications (spreadsheets, progra  
Adobe RGB  
This mode is compatible with Adobe RGB (1998).  
Emulates 72% NTSC color.  
sRGB  
Custom (RGB)  
Use the  
Use the  
or  
or  
button to increase or decrease each of the three colors (R, G, B) independently, in single-digit increments  
button to increase or decrease each of the six colors (R, G, B, C, M, Y) independently, in single-digit increm  
Custom (RGBCMY)  
Video input  
Movie  
Game  
Sports  
Nature  
Hue  
Mode suitable for movie playback.  
Mode suitable for game applications.  
Mode suitable for sports scenes.  
Mode suitable for nature scenes.  
This feature can make the video image color shift from green to purple. Use this feature to adjust the skin tone. Use  
increases the green hue in the image  
or  
increases the purple hue in the image  
NOTE: Hue adjustment is only available for video input.  
Saturation  
Allows you to adjust the color saturation of the video image. Use  
makes video image looks monochrome  
or  
button to adjust the saturation from '0' to '100'  
makes video image looks colorful  
NOTE: Saturation adjustment is only available for video input.  
Reset Color Settings  
Back  
Returns your monitor color settings to those that were set at the time of manufacture.  
Press  
to go back to the main menu.  
Display Settings  
Adjusts the image ratio as 1:1, Aspect or full screen.  
Wide Mode  
NOTE: Wide Mode adjustment is not required at optimal preset resolution 1920 x 1200.  
Horizontal Position  
Vertical Position  
Use the  
Use the  
and  
and  
buttons to adjust image left and right. Minimum is '0' (-). Maximum is '100' (+).  
buttons to adjust image up and down. Minimum is '0' (-). Maximum is '100' (+).  
Sharpness  
Zoom  
This feature can make the image look sharper or softer. Use  
Use the Zoom function to zoom in to specific area of interest.  
or  
to adjust the sharpness from '0' to '100' .  
Using the  
and  
keys to zoom in and out.  
The Phase and Pixel Clock adjustments allow you to adjust your monitor to your preference. These settings are accessed th  
'Image Settings'.  
Pixel Clock  
Phase  
Use the  
and  
buttons to adjust for best image quality.  
If satisfactory results are not obtained using the Phase adjustment, use the Pixel Clock (coarse) adjustment and then use P  
NOTE: Pixel Clock and Phase Adjustments are only available for "VGA" input.  
Dynamic Contrast  
Allows you to increase the level of contrast to provide sharper and more detailed image quality.  
Display Info Displays the monitor's current settings.  
Resets the display settings to the original factory settings.  
Reset Display Settings  
Back  
Press  
to go back to the main menu.  
PIP Settings  
This function brings up a window displaying image from another input source.  
PIP/PBP submenu when PIP/PBP OFF (main source is VGA/DVI-D input)  
PIP/PBP submenu when PIP/PBP ON (main source is VGA/DVI-D input)  
NOTE: When using DVI source, the contrast adjustment is not available.  
There are two modes: Picture in Picture (PIP) and Picture by Picture (PBP)  
PIP Mode  
Use  
and  
to browse and  
to select "Off", "PIP" or "PBP".  
When PIP/PBP is activated, select "Swap" to exchange the input source for the main screen and PIP/PBP window.  
When PIP/PBP  
activated  
Select an input signal for PIP/PBP. (VGA/DVI-D 1/DVI-D 2/DP (DisplayPort)/HDMI/Composite/Component)  
PIP Source  
Use  
and  
to browse and  
to select.  
to select.  
Select PIP window size.  
Use and to browse and  
Size  
Position  
Select PIP window position.  
Use and to browse and  
to select.  
Adjust the brightness level of the picture in PIP/PBP Mode.  
reduces the brightness  
Brightness  
Contrast  
increases the brightness  
Adjust the contrast level of the picture in PIP/PBP Mode.  
reduces the contrast  
increases the contrast  
This function shifts the color of PIP/PBP image to green or purple. This is used to adjust for desired flesh tone color.  
shifts image color towards green  
Hue  
shifts image color towards purple  
Adjust the color saturation of PIP/PBP image.  
makes the image look more monochrome  
makes the image look more colorful  
Saturation  
Press  
to go back to the main menu.  
Back  
Other Settings  
Language  
Language option to set the OSD display to one of five languages (English, Espanol, Francais, Deutsch, Japanese).  
Allows you to adjust the OSD background from opaque to transparent.  
Menu Transparency  
Menu Timer  
OSD Hold Time: Sets the length of time the OSD will remain active after the last time you pressed a button.  
Use the  
and  
buttons to adjust the slider in 5 second increments, from 5 to 60 seconds.  
Menu Lock  
Controls user access to adjustments. When selected, no user adjustments are allowed. All buttons are locked except the m  
NOTE: When the OSD is locked, pressing the menu button for 15 seconds will unlock and allow user access to all applicabl  
pressing the menu button for 15 seconds will activate the Menu Lock function.  
Button Sound The monitor beeps everytime a new option is selected in the menu. This button enables or disables the sound.  
Turns the Audio Power on or off during power save mode.  
Power Save Audio  
Audio Configuration Switches between 2.0 and 5.1 audio output.  
DDC/CI  
DDC/CI (Display Data Channel/Command Interface) allows your monitor parameters (brightness, color balance etc) to be a  
can disable this feature by selecting "Disable".  
Enable this feature for best user experience and optimum performance of your monitor.  
If an image appears to be stuck on the monitor, select LCD Conditioning to help eliminate any image retention. Using the L  
LCD Conditioning several hours. Severe cases of image retention are known as burn-in, the LCD Conditioning feature does not remove burn-  
Reset all OSD settings to the factory preset values.  
Factory Reset  
Press  
to go back to the main menu.  
Back  
Personalize There are three shortcut keys on the front panel. Select one control menu for each shortcut key to allow direct access.  
OSD Warning Messages  
When the monitor does not support a particular resolution mode you will see the following message :  
or  
or  
or  
This means that the monitor cannot synchronize with the signal that it is receiving from the computer. See Monitor Specifications for the Horizontal and Vertical fr  
ranges addressable by this monitor. Recommended mode is 1920 X 1200.  
When monitor enters Power Save mode, the following message appears :  
or  
or  
Activate the computer and wake up the monitor to gain access to the OSD  
If you press any button other than the power button one of the following messages will appear depending on the selected input:  
VGA/DVI-D/HDMI/DisplayPort input  
or  
 
or  
Video Input  
or  
In PIP mode, when the monitor does not sense the selected second signal input, one of the following messages will appear depending upon the selected input  
as long as the OSD screen is closed.  
1. VGA  
2. DVI-D 1  
3. DVI-D 2  
4. HDMI  
or  
or  
or  
5. DisplayPort  
6. Composite  
7. Component  
or  
or  
If either VGA, DVI-D, HDMI or DisplayPort input is selected and all VGA, DVI-D, HDMI and DisplayPort cables are not connected, a floating dialog box as shown be  
or  
or  
or  
NOTE: When the cable is connected back to the input of the monitor, any active PIP/PBP window will disappear. Please enter PIP/PBP submenu to bring bac  
NOTE: The PIP/PBP functions can bring up a picture from a second image source. Thus you can watch images from 1 PC source (D-Sub, DVI, HDMI or Display  
Source (Composite or Component). The functions will not allow for 2 PC sources or 2 Video sources to perform PIP/PBP.  
See Solving Problems for more information.  
Setting the Optimal Resolution  
1. Right-click on the desktop and select Properties.  
2. Select the Settings tab.  
3. Set the screen resolution to 1920 x 1200.  
4. Click OK.  
If you do not see 1920 x 1200 as an option, you may need to update your graphics driver. Depending on your computer, complete one of the following  
procedures.  
If you have a Dell desktop or portable computer:  
¡
Go to support.dell.com, enter your service tag, and download the latest driver for your graphics card.  
If you are using a non-Dell computer (portable or desktop):  
¡
¡
Go to the support site for your computer and download the latest graphic drivers.  
Go to your graphics card website and download the latest graphic drivers.  
 
Using the Dell Soundbar (Optional)  
The Dell Soundbar is a stereo two channel system adaptable to mount on Dell flat panel displays. The Soundbar has a rotary volume and on/off control to  
adjust the overall system level, a blue LED for power indication, and two audio headset jacks.  
1. Attach mechanism  
2. Headphone connectors  
3. Power indicator  
4. Power/Volume control  
Using the Tilt, Swivel and Vertical Extension  
Tilt/Swivel  
With the built-in pedestal, you can tilt and/or swivel the monitor for the most comfortable viewing angle.  
   
NOTE: Stand is attached when the monitor is shipped from the factory.  
Vertical Extension  
Stand extends vertically up to 90+5mm.  
Setting Up Your Monitor  
Dell™ 2709W Flat Panel Monitor  
Important instructions to set the display resolution to 1920x1200 (Optimal)  
For optimal display performance while using the Microsoft® Windows® operating systems, set the display resolution to 1920 x 1200 pixels by performing the  
following steps:  
1. Right-click on the desktop and click Properties.  
2. Select the Settings tab.  
3. Move the slider-bar to the right by pressing and holding left-mouse button and adjust the screen resolution to 1920x1200.  
4. Click OK.  
If you do not see 1920x1200 as an option, you may need to update your graphics driver. Please choose the scenario below that best describes the  
computer system you are using, and follow the provided directions:  
 
Dell™ 2709W Flat Panel Monitor  
Information in this document is subject to change without notice.  
© 2008 Dell Inc. All rights reserved.  
Reproduction in any manner whatsoever without the written permission of Dell Inc. is strictly forbidden.  
Trademarks used in this text: Dell, the DELL logo, are trademarks of Dell Inc; Microsoft and Windows either registered trademarks or trademarks of Microsoft Corporation in the  
United States and/or other countries. Adobe is a trademark of Adobe Systems Incorporated, which may be registered in certain jurisdictions. ENERGY STAR is a registered trademark  
of the U.S. Environmental Protection Agency. As an ENERGY STAR partner, Dell Inc. has determined that this product meets the ENERGY STAR guidelines for energy efficiency.  
Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks and names or their products. Dell Inc. disclaims any  
proprietary interest in trademarks and trade names other than its own.  
Model 2709Wb  
July 2008  
Rev. A02  
 
Setting Up the Monitor  
Dell™ 2709W Flat Panel Monitor User's Guide  
Connecting Your Monitor  
To connect your monitor to the computer perform the following steps/instructions:  
l
l
Turn off your computer and disconnect the power cable.  
Connect either the white (digital DVI-D) display connector cable, the blue (analog VGA) display connector cable, or the black DisplayPort cable to the  
corresponding video port on the back of your computer. Do not use all the cables on the same computer. Use all the cables only when they are  
connected to different computers with appropriate video systems.  
Connecting the White DVI Cable  
NOTE: Your monitor supports two DVI ports. You can either choose DVI-D 1 or DVI-D 2 via source select  
button.  
Connecting the Blue VGA Cable  
Connecting the Black DisplayPort Cable  
NOTE: The graphics are used for the purpose of illustration only. Appearance of the the computer may vary.  
After you have completed connecting the DVI/VGA/DisplayPort cable, follow the procedure below to complete setting up your monitor:  
Plug the power cables for your computer and monitor into a nearby outlet.  
l
 
l
l
Turn on the monitor and the computer.  
If your monitor displays an image, installation is complete. If it does not display an image, see Solving Problems.  
Use the cable management slot on the monitor stand to organize the cables.  
Organizing Your Cables  
After attaching all necessary cables to your monitor and computer, (See Connecting Your Monitor for cable attachment,) use the cable management slot to  
neatly organize all cables as shown above.  
Attaching the Soundbar  
1. Working from the rear of the monitor, attach Soundbar by aligning the two slots with the two tabs along the bottom rear of the monitor.  
2. Slide the Soundbar to the left until it snaps into place.  
3. Connect the Soundbar with the DC power connector.  
4. Insert the mini stereo plug from the rear of the Soundbar into the computer's audio output jack.  
NOTICE: Do not use with any device other than Dell Soundbar  
NOTE: Soundbar Power Connector +12V DC output is for optional Soundbar only.  
   
Solving Problems  
Dell™ 2709W Flat Panel Monitor User's Guide  
CAUTION: Before you begin any of the procedures in this section, follow the Safety Instructions.  
Troubleshooting Your Monitor  
Self-Test Feature Check (STFC)  
Your monitor provides a self-test feature that allows you to check whether your monitor is functioning properly. If your monitor and computer are properly  
connected but the monitor screen remains dark, run the monitor self-test by performing the following steps:  
1. Turn off both your computer and the monitor.  
2. Unplug the video cable from the back of the computer. To ensure proper Self-Test operation, remove both Digital (white connector) and the Analog (blue  
connector) cables from the back of computer.  
3. Turn on the monitor.  
The floating dialog box should appear on-screen (against a black background) if the monitor cannot sense a video signal and is working correctly.  
While in self-test mode, the power LED remains blue. Also, depending upon the selected input, one of the dialogs shown below will continuously scroll  
through the screen.  
or  
or  
4. This box also appears during normal system operation if the video cable becomes disconnected or damaged.  
5. Turn off your monitor and reconnect the video cable; then turn on both your computer and the monitor.  
If your monitor screen remains blank after you use the previous procedure, check your video controller and computer system, because your monitor is  
functioning properly.  
NOTE: Self test feature check is not available for Composite, and Component video modes.  
OSD Warning Messages  
For OSD-related issues, see OSD Warning Messages  
Common Problems  
The following table contains general information about common monitor problems you might encounter.  
Common Symptoms  
What You Experience  
No picture  
Possible Solutions  
No Video/ Power LED off  
l
l
Ensure that the video cable connecting the monitor and the computer is pr  
and secure.  
Verify that the power outlet is functioning properly using any other electric  
     
l
Ensure that the power button is depressed fully.  
No Video/ Power LED on  
Poor Focus  
No picture or no brightness  
l
l
l
Increase brightness & contrast controls via OSD.  
Perform monitor self-test feature check.  
Check for bent or broken pins in the video cable connector.  
Picture is fuzzy, blurry, or ghosting  
l
l
l
l
l
Perform Auto Adjust via OSD.  
Adjust the Phase and Pixel Clock controls via OSD.  
Eliminate video extension cables.  
Reset the monitor to Factory Settings.  
Change the video resolution to the correct aspect ration (16:10).  
Shaky/Jittery Video  
Wavy picture or fine movement  
l
l
l
l
l
Perform Auto Adjust via OSD.  
Adjust the Phase and Pixel Clock controls via OSD.  
Reset the monitor to Factory Settings.  
Check environmental factors.  
Relocate the monitor and test in another room.  
Missing Pixels  
LCD screen has spots  
l
l
Cycle power on-off.  
Pixel that is permanently off is a natural defect that can occur in LCD techn  
Stuck-on Pixels  
Brightness Problems  
LCD screen has bright spots  
Picture too dim or too bright  
l
l
Cycle power on-off.  
Pixel that is permanently off is a natural defect that can occur in LCD techn  
l
l
l
Reset the monitor to Factory Settings.  
Auto Adjust via OSD.  
Adjust brightness & contrast controls via OSD.  
Geometric Distortion  
Screen not centered correctly  
Screen has one or more lines  
l
l
l
Reset the monitor to Factory Settings.  
Auto Adjust via OSD.  
Adjust brightness & contrast controls via OSD.  
NOTE: When using 'DVI-D', the positioning adjustments are not available.  
Horizontal/Vertical Lines  
l
l
l
l
Reset the monitor to Factory Settings.  
Perform Auto Adjust via OSD.  
Adjust Phase and Pixel Clock controls via OSD.  
Perform monitor self-test feature check and determine if these lines are als  
mode.  
l
Check for bent or broken pins in the video cable connector.  
NOTE: When using 'DVI-D', the Pixel Clock and Phase adjustments are not avail  
Synchronization Problems  
Screen is scrambled or appears torn  
l
l
l
l
Reset the monitor to Factory Settings.  
Perform Auto Adjust via OSD.  
Adjust Phase and Pixel Clock controls via OSD.  
Perform monitor self-test feature check to determine if scrambled screen a  
test mode.  
l
l
Check for bent or broken pins in the video cable connector.  
Restart the computer in the safe mode.  
Safety Related Issues  
Intermittent Problems  
Visible signs of smoke or sparks  
Monitor malfunctions on & off  
l
l
Do not perform any troubleshooting steps.  
Contact Dell immediately.  
l
Ensure that the video cable connecting the monitor to the computer is con  
and is secure.  
l
l
Reset the monitor to Factory Settings.  
Perform monitor self-test feature check to determine if the intermittent pro  
self-test mode.  
Missing Color  
Wrong Color  
Picture missing color  
Picture color not good  
l
l
Perform monitor self-test feature check.  
Ensure that the video cable connecting the monitor to the computer is con  
and is secure.  
l
Check for bent or broken pins in the video cable connector..  
l
l
l
Change the Color Setting Mode in the Color Settings OSD to Graphics or V  
to the application.  
Try different Color Preset Settings in Color Settings OSD. Adjust R/G/B valu  
Settings OSD if the Color Management is turned off.  
Change the Input Color Format to PC RGB or YPbPr in the Advance Setting  
Image retention from a static  
image left on the monitor for a  
long period of time  
Faint shadow from the static image  
displayed appears on the screen  
l
l
Use the Power Management feature to turn off the monitor at all times wh  
more information, see Power Management Modes).  
Alternatively, use a dynamically changing screensaver.  
Video Problems  
   
COMMON SYMPTOMS  
No Video  
WHAT YOU EXPERIENCE  
POSSIBLE SOLUTIONS  
No signal indicator is displayed  
l
l
Check Video Input Selection  
¡
Composite: Yellow colored RCA jack  
Component: Red, Blue, Green colored RCA jacks  
¡
Low Quality DVD playback  
Blinking Video  
Picture not crisp and some color distortion  
Video is blinking or discontinuous  
Check DVD connection  
¡
Composite gives good picture  
Component: Red, Blue, Green colored RCA jacks  
¡
l
l
Check DVD connection  
¡
Composite gives good picture  
Component: Red, Blue, Green colored RCA jacks  
¡
Check if DVD player is HDCP compliant.  
¡
Some non-compliant players may exhibit blinking video and others w  
raster screen.  
Product Specific Problems  
SPECIFIC SYMPTOMS  
WHAT YOU EXPERIENCE  
POSSIBLE SOLUTIONS  
Screen image is too small  
Image is centered on screen, but does not  
fill entire viewing area  
l
l
l
Perform monitor reset on "Factory Reset"  
Cannot adjust the monitor with  
the buttons on the front panel  
OSD does not appear on the screen  
Turn the monitor off and unplug the power cord and then plug back and p  
The monitor will not go into  
power saving mode.  
No picture, the LED light is blue. When  
press "+", "-" or "Menu" key, the message  
" No Composite input signal " or " No  
Component input signal " will appear.  
Move mouse or hit any key on the keyboard on the computer or activate v  
access the OSD to set Audio to "off " state.  
No Input Signal when you press No picture, the LED light is blue. When you  
l
l
l
l
Check the signal source Make sure the Computer is not in power saving by  
mouse or pressing any key on the keyboard.  
Check to make sure Video Source to Composite or Component is powered  
video media.  
Check whether the signal cable is plugged in and seated properly. Re-plu  
if necessary.  
the controls.  
press "+", "-" or "Menu" key, the message  
" No Composite input signal " or " No  
Component input signal " will appear.  
Re-boot the computer or video player.  
The monitor will not fill the entire The picture can't fill the height or width of  
screen. the screen.  
l
Due to the non-standard formats of DVDs, the monitor may not show the  
pictures.  
NOTE: When choosing DVI-D, DisplayPort, HDMI, Composite or Component video, Auto Adjust function is not available.  
Universal Serial Bus (USB) Specific Problems  
SPECIFIC SYMPTOMS  
WHAT YOU EXPERIENCE  
POSSIBLE SOLUTIONS  
USB interface is not working  
USB peripherals are not working  
l
l
l
l
l
Check that your monitor is powered ON.  
Reconnect the upstream cable to your computer.  
Reconnect the USB peripherals (downstream connector).  
Switch off and then turn on the monitor again.  
Reboot the computer.  
High Speed USB 2.0 interface is  
slow.  
High Speed USB 2.0 peripherals working  
slowly or not at all.  
l
l
l
l
l
Check that your computer is USB 2.0 capable.  
Verify USB 2.0 source on your computer.  
Reconnect the upstream cable to your computer.  
Reconnect the USB peripherals (downstream connector).  
Reboot the computer.  
Troubleshooting the Dell™ Soundbar  
COMMON SYMPTOMS  
No Sound  
WHAT YOU EXPERIENCE  
POSSIBLE SOLUTIONS  
No power to Soundbar - the power  
indicator is off.  
(built-in DC power supply. i.e. 2709W)  
l
Turn the Power/Volume knob on the Soundbar clockwise to the middle pos  
power indicator (blue LED) on the front of the Soundbar is illuminated.  
Confirm that the power cable from the Soundbar is plugged into the monit  
Confirm that the monitor has power.  
If the monitor has no power, see Monitor Specific Troubleshooting for mon  
problem.  
l
l
l
     
No Sound  
Soundbar has power - power indicator is  
on.  
l
l
l
l
l
l
Plug the audio line-in cable into the computer's audio out jack.  
Set all Windows volume controls to their maximum.  
Play some audio content on the computer (i.e. audio CD, or MP3).  
Turn the Power/Volume knob on the Soundbar clockwise to a higher volum  
Clean and reseat the audio line-in plug.  
Test the Soundbar using another audio source (i.e. portable CD player).  
Distorted Sound  
Computer's sound card is used as the  
audio source.  
l
l
l
l
l
l
l
l
Clear any obstructions between the Soundbar and the user.  
Confirm that the audio line-in plug is completely inserted into the jack of th  
Set all Windows volume controls to their midpoints.  
Decrease the volume of the audio application.  
Turn the Power/Volume knob on the Soundbar counter-clockwise to a lowe  
Clean and reseat the audio line-in plug.  
Troubleshoot the computer's sound card.  
Test the Soundbar using another audio source (i.e. portable CD player).  
Distorted Sound  
Other audio source is used.  
l
l
l
l
l
Clear any obstructions between the Soundbar and the user.  
Confirm that the audio line-in plug is completely inserted into the jack of th  
Decrease the volume of the audio source.  
Turn the Power/Volume knob on the Soundbar counter-clockwise to a lowe  
Clean and reseat the audio line-in plug.  
Unbalanced Sound Output  
Sound from only one side of Soundbar  
l
l
Clear any obstructions between the Soundbar and the user.  
Confirm that the audio line-in plug is completely inserted into the jack of th  
audio source.  
l
l
l
l
Set all Windows audio balance controls (L-R) to their midpoints.  
Clean and reseat the audio line-in plug.  
Troubleshoot the computer's sound card.  
Test the Soundbar using another audio source (i.e. portable CD player).  
Low Volume  
Volume is too low.  
l
l
l
l
l
Clear any obstructions between the Soundbar and the user.  
Turn the Power/Volume knob on the Soundbar clockwise to the maximum v  
Set all Windows volume controls to their maximum.  
Increase the volume of the audio application.  
Test the Soundbar using another audio source (i.e. portable CD player).  
Troubleshooting the Card Reader  
NOTICE: Do not remove the device while reading or writing media. Doing so may cause loss of data or malfunction in the media.  
Problem  
Cause  
Solution  
Drive letter is not assigned.  
(Windows® XP only)  
Conflict with network drive letter.  
A. Right-click My Computer on the desktop, and then click Manage. Under Com  
Management, click Desk Management.  
B. In the list of drives in the right panel, right-click Removable Device and the  
Drive Letter and Paths.  
C. Click Change, and in the drop-down box, specify a drive letter for the Remo  
choosing one that is not assigned to the mapped network drives.  
D. Click OK, and then click OK again  
Drive letter is assigned, but the  
media is not accessible  
The media needs reformatting.  
Right-click the drive in Explorer and choose Format from the resulting menu.  
The media has been ejected  
during writing or erasing.  
Displays the error message, "Error copying Reinsert the media and write or erase again.  
file or folder."  
Format the media for writing or erasing the same folder or file name.  
Displays the error message, "Cannot write  
folder (folder name) or file (file name),"  
during writing, or, "Cannot remove folder  
(folder name) or file(file name),". While  
erasing, you cannot write or erase in the  
same folder or file name.  
Despite the disappearance of the Although the pop-up window disappears  
Format the media for writing or erasing the same folder or file name.  
pop-up window, the media has  
been ejected while the LED was  
blinking.  
during writing, if you eject your media  
while the LED is still blinking, then you  
cannot complete your action on the media.  
Cannot format or write on the  
media.  
Write protect switch is enabled.  
Verify that the write- protect switch of the media is unlocked.  
 

Electrolux 922044 User Manual
Dell Computer Monitor P2010H User Manual
Daewoo DTQ 27S3FC, DTQ 27S4FC, DTQ 25S3FC User Manual
Cypress CY7C1992BV18 User Manual
Cypress CY7C1516KV18 User Manual
Black Box Computer Hardware LMC5110C R3 User Manual
BenQ Computer Monitor G2220HDA User Manual
Belkin F5U140 User Manual
Aluratek Mini SD USB 2 0 User Manual
Adaptec Computer Hardware 1430SA User Manual