Daewoo d Color Television 20V4FCN DTQ 14V1FSN User Manual

S/M No.:CN001N-010  
Service Manual  
ColorTelevision  
CHASSIS : CN-001N  
Model :  
DTQ-14V1FCN/20V1FCN  
DTQ-14V5FCN/20V4FCN  
DTQ-14V1FSN/20V1FSN  
DTQ-14V5FSN/20V4FSN  
DTQ-14V3FSN/20V3FSN  
DTQ-14U1FSN/20U1FSN  
DTQ-14V1FSPN/20V1FSPN  
DTQ-14V5FSPN/20V4FSPN  
DTQ-14U1FSPN/20U1FSPN  
U.S.A  
Canada  
Middle America  
(AC 110V)  
Mexico,Chile,  
Peru (AC 220V)  
DTQ-20V4FCN  
DTQ-14V1FCN  
DTQ-14V5FCN  
DTQ-14V3FCN  
DTQ-14U1FSN  
DAEWOO ELECTRONICS CO., LTD  
http : //svc.dwe.co.kr  
Dec. 2000  
PRODUCT SAFETY SERVICING GUIDELINES FOR AUDIO - VIDEO PRODUCTS  
CAUTION : DO NOT ATTEMPT TO MODIFY THIS PRODUCT IN ANY WAY.  
NEVER PERFORM CUSTOMIZED INSTALLATIONS WITHOUT MANUFAC-  
TURER'S APPROVAL. UNAUTHORIZED MODIFICATIONS WILL NOT ONLY VOID  
THE WARRANTY, BUT MAY LEAD TO YOUR BEING LIABLE FOR ANT RESULT-  
ING PROPERTY DAMAGE OR USER INJURY.  
SERVICE WORK SHOULD BE PERFORMED ONLY AFTER YOU ARE THOR-  
OUGHLY FAMILIAR WITH ALL OF THE FOLLOWING SAFETY CHECKS AND  
SERVICING GUIDELINES. TO DO OTHERWISE, INCREASES THE RISK OF  
POTENTIAL HAZARDS AND INJURY TO THE USER.  
SUBJECT : X-RADIATION  
1. BE SURE PROCEDURES AND INSTRUCTIONS TO ALL SERVICE PERSON-  
NEL COVER THE SUBJECT OF X-RADIATION. THE ONLY POTENTIAL  
SOURCE OF X-RAYS IN CURRENT T.V. RECEIVERS IS THE PICTURE TUBE.  
HOWEVER, THIS TUBE DOES NOT EMIT X-RAYS WHEN THE HIGH VOLT-  
AGE IS AT THE FACTORY SPECIFIED LEVEL. THE PROPER VALUE IS  
GIVEN IN THE APPLICABLE SCHEMATIC. OPERATION AT HIGHER VOLT-  
AGES MAY CAUSE A FAILURE OF THE PICTURE TUBE OR HIGH VOLTAGE  
SUPPLY AND UNDER CERTAIN CIRCUMSTANCES, AMY PRODUCE RADIA-  
TION IN EXCESS OF DESIRABLE LEVELS.  
WHILE SERVICING, USE AN ISOLATION TRANSFORMER FOR PROTECTION  
FROM A.C. LINE SHOCK.  
2. ONLY FACTORY SPECIFIED C.R.T ANODE CONNECTORS MUST BE USED.  
DEGAUSSING SHIELDS ALSO SERVE AS X-RAY SHIELD IN COLOR SETS.  
ALWAYS RE-INSTALL THEM.  
SAFETY CHECKS  
AFTER THE ORIGINAL SERVICE PROBLEM HAS BEEN CORRECTED, A CHECK  
SHOULD BE MADE OF THE FOLLOWING:  
3. IT IS ESSENTIAL THAT SERVICE PERSONNEL HAVE AVAILABLE AN ACCU-  
RATE AND RELIABLE HIGH VOLTAGE METER. THE CALIBRATION OF THE  
METER SHOULD BE CHECKED PERIODICALLY AGAINST A REFERENCE  
STANDARD. SUCH AS THE ONE AVAILABLE AT YOUR DISTRIBUTOR.  
4. WHEN THE HIGH VOLTAGE CIRCUITRY IS OPERATING PROPERLY THERE  
IS NO POSSIBILITY OF AN X-RADIATION PROBLEM. EVERY TIME A COLOR  
CHASSIS IS SERVICED, THE BRIGHTNESS SHOULD BE RUN UP AND  
DOWN WHILE MONITORING THE HIGH VOLTAGE WITH A METER TO BE  
CERTAIN THAT THE HIGH VOLTAGE DOES NOT EXCEED THE SPECIFIED  
VALUE AND THAT IT IS REGULATING CORRECTLY. WE SUGGEST THAT  
YOU AND YOUR SERVICE ORGANIZATION REVIEW TEST PROCEDURES  
SO THAT VOLTAGE REGULATION IS ALWAYS CHECKED AS A STANDARD  
SERVICING PROCEDURE, AND THAT THE HIGH VOLTAGE READING BE  
RECORDED ON EACH CUSTOMER’S INVOICE.  
5. WHEN TROUBLESHOOTING AND MAKING TEST MEASUREMENTS IN A  
PRODUCT WITH A PROBLEM OF EXCESSIVE HIGH VOLTAGE, AVOID  
BEING UNNECESSARILY CLOSE TO THE PICTURE TUBE AND THE HIGH  
VOLTAGE SUPPLY. DO NOT OPERATE THE PRODUCT LONGER THAN IS  
NECESSARY TO LOCATE THE CAUSE OF EXCESSIVE VOLTAGE.  
6. REFER TO HV, B+ AND SHUTDOWN ADJUSTMENT PROCEDURES  
DESCRIBED IN THE APPROPRIATE SCHEMATIC AND DIAGRAMS (WHERE  
USED).  
SUBJECT:FIRE & SHOCK HAZARD  
1. BE SURE THAT ALL COMPONENTS ARE POSITIONED IN SUCH A WAY AS  
TO AVOID POSSIBILITY OF ADJACENT COMPONENT SHORTS. THIS IS  
ESPECIALLY IMPORTANT ON THOSE MODULES WHICH ARE TRANS-  
PORTED TO AND FROM THE REPAIR SHOP.  
2. NEVER RELEASE A REPAIR UNLESS ALL PROTECTIVE DEVICES SUCH AS  
INSULATORS, BARRIERS, COVERS, SHIELDS, STRAIN RELIEFS, POWER  
SUPPLY CORDS, AND OTHER HARDWARE HAVE BEEN REINSTALLED PER  
ORIGINAL DESIGN. BE SURE, THAT THE SAFETY PURPOSE OF THE  
POLARIZED LINE PLUG HAS NOT BEEN DEFEATED.  
3. SOLDERING MUST BE INSPECTED TO DISCOVER POSSIBLE COLD SOL-  
DER JOINTS, SOLDER SPLASHES OF SHARP SOLDER POINTS. BE CER-  
TAIN TO REMOVE ALL LOOSE FOREIGN PARTICLES.  
4. CHECK FOR PHYSICAL EVIDENCE OF DAMAGE OR DETERIORATION TO  
PARTS AND COMPONENTS, FOR FRAYED LEADS, DAMAGED INSULATION  
(INCLUDING A.C. CORD), AND REPLACE IF NECESSARY. FOLLOW ORIGI-  
NAL LAYOUT, LEAD LENGTH AND DRESS.  
5. NO LEAD OR COMPONENT SHOULD TOUCH A RECEIVING TUBE OR A  
RESISTOR RATED AT 1 WATT OR MORE. LEAD TENSION AROUND PRO-  
TRUDING METAL SURFACES MUST BE AVOIDED.  
6. ALL CRITICAL COMPONENTS SUCH AS FUSES, FLAMEPROOF RESISTOR,  
CAPACITORS, ETC. MUST BE REPLACED WITH EXACT FACTORY TYPES.  
DO NOT USE REPLACEMENT COMPONENTS OTHER THAN THOSE SPECI-  
FIED OR MAKE UNRECOMMENDED CIRCUIT MODIFICATIONS.  
SUBJECT : IMPLOSION  
1. ALL DIRECT VIEWED PICTURE TUBES ARE EQUIPPED WITH AN INTEGRA  
IMPLOSION PROTECTION SYSTEM. BUT CARE SHOULD BE TAKEN TO  
AVOID DAMAGE DURING INSTALLATION. AVOID SCRATCHING THE  
TUBE. OF SCRATCHED REPLACE IT.  
7. AFTER RE-ASSEMBLY OF THE STE ALWAYS PERFORM AN A.C. LEAKAGE  
TEST ON ALL EXPOSED METALLIC PARTS OF THE CABINET. (THE CHAN-  
NEL SELECTOR KNOB, ANTENNA TERMINALS, HANDLE AND SCREWS) TO  
BE SURE THE SET IS SAFE TO OPERATE WITHOUT DANGER OF ELECTRI-  
CAL SHOCK. DO NOT USE A LINE ISOLATION TRANSFORMER DURING  
THIS TEST USE AN A.C. VOLTMETER, HAVING 5000 OHMS PER VOLT OR  
MORE SENSITIVITY, IN THE FOLLOWING MANNER : CONNECT A 1500 OHM  
10 WATT RESISTOR, PARALLELED BY A .15 MFD. 150V A.C. TYPE CAPACI-  
TOR BETWEEN A KNOWN GOOD EARTH GROUND (WATER POPE, CON-  
DUIT, ETC.) AND THE EXPOSED METALLIC PARTS, ONE AT A TIME.  
MEASURE THE A.C. VOLTAGE ACROSS THE COMBINATION OF 1500 OHM  
RESISTOR AND .15 MFD CAPACITOR. REVERSE THE A.C. PLUG AND  
REPEAT A.C. VOLTAGE MEASUREMENTS FOR EACH EXPOSED METALLIC  
PART. VOLTAGE MEASURED MUST NOT EXCEED .75 VOLTS R.M.S THIS  
CORRESPONDS TO 0.5 MILLIAMP A.C. NAY VALUE EXCEEDING THIS LIMIT  
CONSTITUTES A POTENTIAL SHOCK HAZARD AND MUST BE CORRECTED  
IMMEDIATELY.  
2. USE ONLY RECOMMENDED FACTORY REPLACEMENT TUBES.  
SUBJECT : TIPS ON PROPER INSTALLATION  
1. NEVER INSTALL ANY PRODUCT IN A CLOSED-IN RECESS, CUBBYHOLE OR  
CLOSELY FITTING SHELF SPACE, OVER OR CLOSE TO HEAT DUCT, OR IN  
THE PATH OF HEATED AIR FLOW.  
2. AVOID CONDITIONS OF HIGH HUMIDITY SUCH AS: OUTDOOR PATIO  
INSTALLATIONS WHERE DEW IS A FACTOR, NEAR STEAM RADIATORS  
WHERE STEAM LEAKAGE IS A FACTOR, ETC.  
3. AVOID PLACEMENT WHERE DRAPERIES MAY OBSTRUCT REAR VENTING.  
THE CUSTOMER SHOULD ALSO AVOID THE USE OF DECORATIVE  
SCARVES OR OTHER COVERINGS WHICH MIGHT OBSTRUCT VENTILA-  
TION.  
4. WALL AND SHELF MOUNTED INSTALLATIONS USING A COMMERCIAL  
MOUNTING KIT, MUST FOLLOW THE FACTORY APPROVED MOUNTING  
INSTRUCTIONS. A PRODUCT MOUNTED TO A SHELF OR PLATFORM MUST  
RETAIN ITS ORIGINAL FEET (OR THE EQUIVALENT THICKNESS IN SPAC-  
ERS)TO PROVIDE ADEQUATE AIR FLOW ACROSS THE BOTTOM, BOLTS  
OR SCREWS USED FOR FASTENERS MUST NOT TOUCH ANY PARTS OR  
WIRING. PERFORM LEAKAGE TEST ON CUSTOMIZED INSTALLATIONS.  
5. CAUTION CUSTOMERS AGAINST THE MOUNTING OF A PRODUCT ON  
SLOPING SHELF OR A TILTED POSITION, UNLESS THE PRODUCT IS  
PROPERLY SECURED.  
A.C. VOLTMETER  
0.15 uF  
GOOD EARTH GROUND  
SUCH AS THE WATER  
PIPE, CONDUIT, ETC.  
PLACE THIS PROBE  
ON EACH EXPOSED  
METAL PART  
1500  
OHM  
10WATT  
6. A PRODUCT ON A ROLL-ABOUT CART SHOULD BE STABLE ON ITS MOUNT-  
ING TO THE CART. CAUTION THE CUSTOMER ON THE HAZARDS OF TRY-  
ING TO ROLL A CART WITH SMALL CASTERS ACROSS THRESHOLDS OR  
DEEP PILE CARPETS.  
7. CAUTION CUSTOMERS AGAINST THE USE OF A CART OR STAND WHICH  
HAS NOT BEEN LISTED BY UNDERWRITERS LABORATORIES. INC. FOR  
USE WITH THEIR SPECIFIC MODEL OF TELEVISION RECEIVER OR  
GENERICALLY APPROVED FOR USE WITH T.V.S OF THE SAME OR  
LARGER SCREEN SIZE.  
SUBJECT : GRAPHIC SYMBOLS  
THE LIGHTNING FLASH WITH ARROWHEAD SYMBOL,  
WITHIN AN EQUILATERAL TRIANGLE, IS INTENDED  
TO ALERT THE SERVICE PERSONNEL TO THE PRES-  
ENCE OF UNINSULATED “DANGEROUS VOLTAGE”  
THAT MAY BE OF SUFFICIENT MAGNITUDE TO CON-  
STITUTE A RISK OF ELECTRIC SHOCK.  
8. CAUTION CUSTOMERS AGAINST THE USE OF EXTENSION CORDS,  
EXPLAIN THAT A FOREST OF EXTENSIONS SPROUTING FROM A SINGLE  
OUTLET CAN LEAD TO DISASTROUS CONSEQUENCES TO HOME AND  
FAMILY.  
THE EXCLAMATION POINT WITHIN AN EQUILATERAL  
TRIANGLE IS INTENDED TO ALERT THE SERVICE  
PERSONNEL TO THE PRESENCE OF IMPORTANT  
SAFETY INFORMATION ON SERVICE LITERATURE.  
2
PRODUCT SAFETY SERVICING GUIDELINES FOR COLOR TELEVISION RECEIVERS  
CAUTION : Do not attempt to modify this product in any way. Unau-  
thorized modifications will not only void the warranty, but may lead to  
your being liable for any resulting property damage or user injury.  
Service work should be performed only after you are thoroughly  
familiar with all of the following safety checks and servicing guide-  
lines. To do otherwise, increases the risk of potential hazards and  
injury to the user.  
GRAPHIC SYMBOLS :  
The lightning flash with arrowhead symbol,  
within an equilateral triangle, is intended to alert  
the service personnel to the presence of uninsu-  
lated “dangerous voltage” that may be of suffi-  
cienty magnitude to constitute a risk of electric  
shock.  
SAFETY CHECKS  
The exclamation point within an equilateral tri-  
angle is intended to alert the service personnel  
to the presence of important safety information  
in service literature.  
After the original service problem has been corrected, a check should  
be made of the following:  
SUBJECT : FIRE & SHOCK HAZARD  
Fuse symbol is printed on pcb adjacent to the  
fuse, with “RISK OF FIRE REPLACE FUSE AS  
MARKED”. The symbol is explained in the ser-  
vice manual with the following wording or equiv-  
alent.  
1. Be sure that all components are positioned in such a way as to  
avoid possibility of adjacent component shorts. This is especially  
important on those chassis which are transported to and from the  
repair shop.  
2. Never release a repair unless all protective devices such as insula-  
tors, barriers, covers, shields, strain reliefs, and other hardware  
have been reinstalled per original design.  
“CAUTION : FOR CONTINUED PROTECTION AGAINST FIRE  
HAZARD, REPLACE ONLY WITH SAME TYPE (4A, 125V)” and  
ATTENTION: AFIN D’ASSU UNE PROTECTION PERMANENTE  
3. Soldering must be inspected to discover possible cold solder joints,  
frayed leads, damaged insulation (including A.C. cord), solder  
splashes or sharp solder points. Be certain to remove all loose for-  
eign particals.  
CONTRE LES RISQUES D’INCENDIE, REMPLACER UNIQUE-  
MENT PAR UN FUSIBLE DE MEME TYPE ET DE ”4A, 125V”.  
SUBJECT : X-RADIATION  
4. Check for physical evidence of damage or deterioration to parts  
and components, and replace if necessary follow original layout,  
lead length and dress.  
1. Be sure procedures and instructions to all service personnel cover  
the subject of X-rays in current T.V. receivers is the picture tube.  
However, this tube does not emit X-rays when the high voltage is  
at the factory specified level. The proper value is given in the appli-  
cable schematic. Operation at higher voltages may cause a failure  
of the picture tube or high voltage supply and, under certain cir-  
cumstances, may produce radiation in excess of desirable levels.  
2. Only factory specified C.R.T. anode connectors must be used.  
Degaussing shields also serve as X-ray shield in color sets.  
Always re-install them.  
5. No leads or components should touch a receiving tube or a resistor  
rated at 1 watt or more. Lead tension around protruding metal sur-  
faces must be avoided.  
6. All critical components such as fuses, flameproof resistors, capaci-  
tors, etc. must be replaced with exact factory types. Do not use  
replacement components other than those specified or make  
unrecommended circuit modifications.  
7. After re-assembly of the set always perform an A.C. leakage test  
on all exposed metallic parts of the cabinet, (the channel selector  
knob, antenna terminals, handle and screws) to be sure the set is 3. It is essential that the serviceman has available an accurate and  
safe to operate without danger of electrical shock. Do not use a  
line isolation transformer during this test. Use an A.C. voltmeter,  
having 5000 ohms per volt or more sensitivity, in the following  
reliable high voltage meter. The calibration of the meter should be  
checked perio - dically against a reference standard. Such as the  
one available at your distributor.  
manner : connect a 1500 ohm 10 watt resistor, paralleled by a 15 4. When the high voltage circuitry is operating properly there is no  
mfd. 150V A.C. type capacitor between a known good earth  
ground (9water pipe, conduit, etc.) and the exposed metallic parts,  
one at a time. Measure the A.C. voltage across the combination of  
1500 ohm resistor and 0.15 MFD capacitor. Reverse the A.C. plug  
and repeat A.C. voltage measurements for each exposed metallic  
part. Voltage measured must not exceed 0.75 volts R.M.S. This  
corresponds to 0.5 milliamp A.C. Any value exceeding this limit  
constitutes a potential shock hazard and must be corrected imme-  
diately.  
possibility of an X-radiation problem. Every time a color chassis is  
serviced, the brightness should be run up and down while monitor-  
ing the high voltage with a meter to be certain that the high voltage  
does not exceed the specified value and that it is regulating cor-  
rectly. We suggest that you and your service organization review  
test procedures so that voltage regulation is always checked as a  
standard servicing procedure. And that the high voltage reading be  
recorded on each customer’s invoice.  
5. When troubleshooting and making test measurements in a receiver  
with a problem of excessive high voltage, avoid being unnecessarily  
close to the picture tub eand the high voltage compartment.  
Do not operate the chassis longer than is necessary to locate the  
cause of excessive voltage.  
A.C. VOLTMETER  
6. Refer to HV, B+and Shutdown adjustment procedures described in  
the appropriate schematic and diagrams(where used).  
0.15 uF  
Good earth ground,  
such as the water  
pipe, conduit, etc.  
Place this probe  
on each exposed  
metal part.  
1500 OHM  
10WATT  
3
4. Wall and shelf mounted installations using a commercial mounting  
kit, must follow the factory approved mounting instructions. A  
receiver mounted to a shelf or platform must retain its original  
feet(or the equivalent thickness in spacers) to provide adequate  
are flow across the bottom, bolts or screws used for fasteners  
must not touch and parts or wiring. Perform leakage test on cus-  
tomized installations.  
SUBJECT : IMPLOSION  
1. All direct viewed picture tubes are equipped with an integral implo-  
sion protection system, but care should be taken to avoid damage  
during installation. Avoid scratching the tube. If scratched, replace  
it.  
2. Use only recommended factory replacement tubes.  
5. Caution customers against the mounting of a receiver on sloping  
shelf or a tilted position, unless the receiver is properly secured.  
6. A receiver on a roll-about cart should be stable on its mounting to  
the cart. Caution the customer on the hazards of trying to roll a cart  
with small casters across thresholds or deep pile carpets.  
7. Caution customers against the use of a cart or stand which has not  
been listed by underwriters laboratories, inc. For use with their  
specific model of television receiver or generically approved for  
use with T.V.’s of the same or larger screen size.  
SUBJECT : TIPS ON PROPER INSTALLATION  
1. Never install any receiver in closed-in recess, cubbyhole or closely  
fitting shelf space over, or close to heat duct, or in the path of  
heated air flow.  
2. Avoid conditions of high humidity such as : Outdoor patio installa-  
tions where dew is a factor. Near steam radiators where steam  
leakage is a factor, etc.  
3. Avoid placement where draperies may obstruct rear venting. The  
customer should also avoid the use of decorative scarves or other  
coverings which might obstruct ventilation.  
4
SPECIFICATIONS  
DTQ-14/20V1FCN  
MODEL DTQ-14V5/20V4FCN  
DTQ-14/20V1FSN  
DTQ-14/20V1FSPN  
DTQ-14V5/20V4FSPN  
DTQ-14/20U1FSN DTQ-14/20U1FSPN  
REMARKS  
ITEMS  
DTQ-14V5/20V4FSN  
DTQ-14/20V3FSN  
TV STANDARD  
POWER INPUT  
NTSC-M  
AC 120V 60 Hz  
AC 220V 50/60 Hz  
14 = 55W  
20 = 68W  
POWER CONSUMPTION  
TUNING SYSTEM  
Frequency Synthesizer ( FS ) Tuning System  
VHF : 2 ~ 13 (12)  
UHF : 14 ~ 69 (56)  
CATV : 1 ~ 125 (125)  
TUNING RANGES  
SOUND OUTPUT  
SPEAKER  
1.3 W  
1.3 W+1.3 W  
3 W 8 ohm  
1.3 W  
ANTENNA INPUT  
IMPEDANCE  
75 ohm Unbalanced  
AUXILIARY  
INPUT TERMINAL  
Front : Video, Audio  
Rear : Video, Audio  
Picture IF Carrier Frequency : 45.75 MHz  
Sound IF Carrier Frequency : 41.25 MHz  
Color Sub-Carrier Frequency : 42.17 MHz  
INTERMEDIATE  
FREQUENCIES  
REMOTE CONTROL  
R-43A01  
3-Language OSD  
With CAPTION  
SPECIAL FUNCTIONS  
Wake-up On/Off Time  
Sleep Timer  
Power Restore  
5
BLOCK DIAGRAM  
6
ALIGNMENT INSTRUCTIONS  
1. SERVICE MODE ADJUSTMENTS  
Follow the steps below whenever service adjustment is required. See Table- A and Table- B to determine if  
service adjustments are required.  
1) How to enter the service mode using the user remote control.  
·
·
·
Turn the set on.  
Direct the remote control to the reception window of TV.  
Push buttons of remote control in sequence as follows.  
1
®
MUTE  
®
DISPLAY  
®
MUTE  
·
Then, the screen will appear as follows.  
S2  
S5  
S6  
S8  
S9  
SCRN  
IFC  
GEO  
W/B  
DP  
S12 FACT  
S7  
PTRN NORMAL  
·
Using the channel up or channel down button, select the item you wish to adjust.  
(The color of selected item turns into the red.)  
·
Press the volume up or down button to enter in the service mode you wish to adjust.  
2) How to memorize the adjusted values in the service mode.  
·
Must press DISPLAY button the state which the screen is displaying each of service menus  
after all adjustments are completed each of all service menu.  
Table-A : Adjust the values of service mode when a part is replaced.  
ADJUSTMENT  
PART  
NOTES  
REPLACED  
NECESSARY UNNECESSARY  
I701  
(U-COM)  
Data is stored in I703.  
O
O
I101  
(MAIN)  
Initial setting values are written from I701.  
Adjusting Items  
S5  
S6  
S8  
S9  
RFAGCD  
I703  
(EEPROM)  
O
O
H.PHASE/V.POSI/V.SIZE  
RD/BD/RB/GB/BB  
Subbrightness  
CRT  
Adjust items related to picture tube only.(White Balance adjustment)  
7
ALIGNMENT INSTRUCTIONS  
Table-B  
DATA  
RANGE  
MODE  
ADJUSTMENT ITEMS  
Screen Adjustment  
REMARKS  
INITIAL  
S2  
-
-
Auto RF AGC  
-
-
Video Level (VIDEOL)  
RF AGC Delay (RFAGCD)  
FM Level (FM.LEV)  
AGC Point  
7
0 ~ 7  
0 ~ 63  
0 ~ 31  
-
Must be set to 7  
*
Align RF AGC threshold  
Must be set to 20  
S5  
8
3.75  
Select AGC reference voltage  
A/D VALUE  
-
-
Horizontal Phase(H.PHASE)  
Vertical Position (V.POSI)  
Vertical Size (V.SIZE)  
NO SD POWER OFF  
Vertical S-Correction (V SC)  
Vertical Linearity (V LIN)  
Internal Black  
*
0 ~ 31  
0 ~ 63  
0 ~ 127  
-
Align sync to flyback pulse, using internal cross pattern(S7)  
Align vertical DC bias, using internal cross pattern(S7)  
Align vertical amplitude, using internal cross pattern(S7)  
Automatically turn off in 15min for no received signal.  
Must be set to 6  
*
*
YES  
0
S6  
S7  
S8  
0 ~ 31  
0 ~ 31  
-
20  
-
Must be set to 16  
Display internal BLACK pattern  
Display internal 100% WHITE  
Display internal 60% WHITE  
Internal 100% White  
Internal 60% White  
Internal Cross Pattern  
Red Drive (RD)  
-
-
-
-
-
-
Display internal CROSS pattern  
Align RED OUT AC level  
*
0 ~ 127  
0 ~ 15  
0 ~ 127  
0 ~ 255  
0 ~ 255  
0 ~ 255  
0 ~ 127  
0 ~ 27  
0 ~ 27  
0 ~ 27  
Green Drive (GD)  
Blue Drive (BD)  
10  
*
Must be set to 10  
Align BLUE OUT AC level  
Red Bias (RB)  
*
Align RED OUT DC level  
Green Bias (GB)  
Blue Bias (BB)  
*
Align GREEN OUT DC level  
*
Align BLUE OUT DC level  
Subbrightness  
*
Align common RGB DC level  
Contrast  
10  
27  
15  
S9  
Tint  
Color  
S12  
Forwarding Mode  
-
Factory Initialization  
*
indicates the items with different settings each of sets  
2. ASSEMBLY ADJUSTMENTS  
1) SCREEN ADJUSTMENT (S2)  
·
·
·
Enter the service mode and select service adjustment S2.  
You cna see the one horizontal line on the screen.  
Adjust the Screen Control Volume (located on FBT) so that the horizontal line onscreen may be  
disappeared.  
·
Press the volume up or down button to exit in the screen adjustment mode.  
NOTE  
IN THE SCREEN ADJUSTMENT MODE, DONT PRESS OTHER BUTTONS EXCEPT VOLUME UP OR DOWN BUTTON.  
8
ALIGNMENT INSTRUCTIONS  
2) FOCUS ADJUSTMENT  
Turn in a local station and adjust the Focus Control knob (located on FBT) for best picture  
details at high light condition.  
·
3) RF AGC DELAY ADJUSTMENT (S5)  
·
·
·
Receive a good local channel.  
Enter the service mode and select service adjustment S5.  
You can see the OSD as shown in below.  
IF  
CONTROL  
RFAGC  
AUTO  
START  
VIDEOL  
7
RFAGCD  
FM.LEV  
10  
8
AGC POINT  
3.75  
A/D VALUE : 8DH  
¡ã ¡å MOVE ¢¸ ¢º ADJUST RECALL : SET  
·
·
Select RFAGCD item, press the volume up or down button until noise or beat in picture disappears.  
Press the DISPLAY button to memorize the data.  
4) GEOMETRIC ADJUSTMENTS (S6)  
·
·
Enter the service mode and select service adjustment S7.  
Whenever you select the “S7” using the volume up or down button, the screen is changing like this.  
NORMAL  
BLACK  
WHITE100  
WHITE60  
CROSS  
·
·
·
Using the volume up or down button, select internal cross pattern.  
Select service adjustment S6  
You can see the OSD as shown in below.  
GEOMETRY  
H. PHASE 20  
V. POSI 29  
V. SIZE 70  
NO SD POWER OFF YES  
V
V
SC  
0
LIN  
20  
¡ã ¡å MOVE ¢¸ ¢º ADJUST RECALL : SET  
4-1. Horizontal Position Adjustment  
·
Select H.PHASE item, adjust H.PHASE data value to obtain proper horizontal centering of the  
internal cross pattern at the left and right of the screen.  
4-2. Vertical Position Adjustment  
·
Select V.POSI item, adjust V.POSI data value to center the raster properly on thescreen.  
9
ALIGNMENT INSTRUCTIONS  
4-3. Vertical Size Adjustment  
·
Select “V.SIZE” item, adjust “V.SIZE” data value to proper vertical size as follows.  
5) WHITE BALANCE ADJUSTMENT(S8)  
·
·
·
Receive a good local channel.  
Enter the service mode and select service adjustment S8.  
You can see the OSD as shown in below.  
RD  
GD  
BD  
58  
10  
65  
RB  
GB  
BB  
105  
160  
100  
¡ã ¡å MOVE ¢¸ ¢º ADJUST RECALL : SET  
·
·
Using volume up or volume down, adjust service adjustment data of RD/GD/BD and RB/GB/BB until a good gray  
scale with normal whites is obtained.ALIGNMENT INSTRUCTIONS  
Press the DISPLAY button to memorize the data.  
6) DIGITAL PRESET(D.P) ADJUSTMENTS(S9)  
SUBBRIGHTNESS ADJUSTMENT  
·
·
·
Receive a good local channel.  
Enter the service mode and select service adjustment S9.  
You can see the OSD as shoown in below.  
D.P.  
SUB BRIGHTNESS  
CONTRAST  
TINT  
64  
10  
27  
15  
COLOR  
¡ã ¡å MOVE ¢¸ ¢º ADJUST RECALL : SET  
10  
ALIGNMENT INSTRUCTIONS  
·
·
Select Subbrightness item, adjust Subbrightness data value to obtain normal brightness level.  
Press the DISPLAY button to memorize the data.  
CONTRAST  
Fixed value = 27  
·
TINT  
·
Fixed value = 32  
COLOR  
·
Fixed value = 20  
7) FACTORY OUTGOING MODE (S12 : FACT)  
·
·
If you select the S12, then the set becomes factory outgoing status.  
You can see the OSD “outgoing OK”  
11  
ALIGNMENT INSTRUCTIONS  
3. PARENTAL CONTROL PASSWORD SETTINGS  
If user forget Parental Control Password as follows.  
1) CHANGE THE PASSWORD.  
• Turn the set on.  
• Direct the remote control to the reception window of your TV/VCR  
• Using the MENU buttons, select the Special menu.  
• Using the the channel up ( ¡ã ) or down ( ¡å ) duttons, select prental control.  
• Using the volume up ( ¢º ), set the password Menu.  
• Push buttons of remote control in sequence as follows.  
2
2
1
1
• Parental control password is reset.  
• Using the 0~9 buttons, enter the password.  
• Using the 0~9 buttons, repeat the password.  
Special  
Parental control  
Closed Caption : OFF  
Enter the Password  
# # # #  
CC on Mute : OFF  
Power Restore : OFF  
Parental Control  
[0 - 9] : Adjust  
n
Exit  
Select  
Enter  
n
Exit  
Parental control  
Parental control  
Enter New Password  
Repeat the Password  
# # # #  
n
n
[0 - 9] : Adjust  
Exit  
[0 - 9] : Adjust  
Exit  
2) RESET THE PASSWORD  
• Turn the set on.  
• Direct the remote control to the reception window of your TV/VCR.  
• Push buttons of remote control in sequence as follows.  
1 › MUTE › INFO › MUTE  
• Then, the screen will appear as follows.  
FIELE SVC  
S2 SCRN V.=02h RCCR=00h  
S5 IFC  
S6 GEO  
S8 W/B  
S9 DP  
S12 FACT  
S7 PTRN NORMAL  
¢º S10 SOUND  
• Using the channel up (¡ã ) or down ( ¡å ) buttons, select S12 FACT.  
Press the volume up ( ¢º ) button, the set becomes factory outgoing status.  
• Parental control password is reset.  
• Using the MENU buttons, select the parental control menu, set the new password.  
12  
VOLTAGE CHART  
MODE  
MODE  
LOC  
I101  
PIN  
LOC  
PIN  
ON  
OFF  
0
ON  
OFF  
0
1
2.37  
2.3  
44  
45  
46  
47  
48  
49  
50  
51  
52  
53  
54  
2.73  
1.94  
2.36  
2.44  
4.25  
4.25  
3.56  
3.04  
1.98  
2.39  
3.11  
2
0
0
3
2.63  
2.22  
2.88  
2.88  
0
0
4
0.49  
0
0
5
0.51  
0.51  
0
6
0
70  
8
0
4.92  
2.25  
2.29  
4.9  
0.57  
0
0.65  
0.32  
0
9
10  
11  
12  
13  
14  
15  
16  
17  
18  
19  
20  
21  
22  
23  
24  
25  
26  
27  
28  
29  
30  
31  
32  
33  
34  
35  
36  
37  
38  
39  
40  
41  
42  
43  
0.28  
4.89  
4.84  
0
0.3  
4.85  
3.94  
1.5  
MODE  
LOC  
I301  
PIN  
ON  
OFF  
0
1
2
3
4
5
6
7
0
0
1.53  
1.53  
0
0
13.35  
26.34  
2.22  
2.22  
25.85  
2.33  
0
0
3.63  
0
0
8.04  
2.52  
2.63  
2.59  
0.2  
0
0
0
0
0
0
0
MODE  
MODE  
LOC  
I401  
PIN  
0
ON  
OFF  
0
0.22  
2.56  
5.14  
2.65  
0.69  
0.81  
1.71  
0
0
1
7.62  
0
20  
3
0
4.23  
2.2  
0.16  
1.37  
1.4  
0
5.05  
0.6  
LOC  
I601  
PIN  
ON  
OFF  
1
14.55  
7.56  
7.81  
0.87  
10.92  
(MONO ONL2Y)  
5.52  
5.87  
0.82  
0
3
NC  
2.79  
0
NC  
0.31  
0
4
50  
60  
70  
80  
90  
10  
11  
12  
13  
14  
15  
16  
0
0
0
0
0.36  
3.41  
0.55  
2.81  
3.27  
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0.35  
0
0
0
0
0
0
0
0
2.52  
4.95  
0
0
0.5  
0
13  
VOLTAGE CHART  
MODE  
MODE  
LOC  
I701  
PIN  
LOC  
I703  
PIN  
ON  
4.9  
OFF  
4.89  
4.8  
4.99  
4.99  
0
ON  
0
OF  
0
1
1
2
4.81  
5.04  
5.04  
20  
30  
40  
5
0
3
0
4
0
50  
6
4.89  
4.86  
4.86  
4.83  
0
1.9  
2.68  
4.97  
5.04  
0
1.9  
2.66  
4.92  
4.99  
0
6
7
70  
8
8
5.04  
4.99  
9
MODE  
LOC  
I801  
PIN  
10  
11  
12  
13  
14  
15  
16  
17  
18  
19  
20  
21  
22  
23  
24  
25  
ON  
OF  
2.22  
0
0.49  
4.89  
4.89  
3.37  
2.47  
3.52  
4.99  
4.99  
0
1
2
3
4
5
6
7
6.72  
163.8  
14.4  
4.53  
2.35  
7.55  
5.04  
4.12  
173.53  
11.02  
3.21  
3.91  
3.45  
4.55  
4.95  
3.4  
2.69  
0
4.65  
4.14  
0
0
0
0
0
0
0
NC  
NC  
0
NC  
NC  
0
MODE  
LOC  
I701  
PIN  
ON  
0
OFF  
0
26  
27  
28  
29  
30  
31  
32  
33  
34  
35  
36  
3.81  
4.97  
4.77  
5.04  
4.08  
5.04  
0
3.46  
4.92  
4.71  
4.99  
0
4.99  
0
5.04  
0
4.99  
0
0
0
14  
VOLTAGE CHART  
MODE  
MODE  
LOC  
PIN  
LOC  
PIN  
ON  
5.02  
3.32  
2.49  
38.6  
0
OFF  
ON  
5.02  
0
OFF  
5
C
0
C
E
B0  
C
E
B
C
E
B
C
E
B
C
E
B
C
E
B
C
E
B
Q201  
E
3.28  
Q703  
0
B
2.48  
0
C
42.28  
4.93  
4.95  
4.32  
5.02  
0.21  
0.07  
2.89  
0
4.9  
4.92  
4.29  
4.2  
5
Q401  
Q402  
Q403  
Q404  
Q602  
Q701  
Q702  
E
0
Q704  
Q707  
Q760  
Q804  
Q805  
Q851  
B0  
C
0
132  
0
0
E
0
B0  
C
0
4.9  
0
0.59  
0
0
E
0
0
B
0
0.66  
0
0
0.68  
0
C
10.1  
0
0.4  
E
0
133.1  
132.6  
12.31  
5.02  
5.6  
119.38  
118.96  
5
B0  
C
0
9.71  
1.69  
2.31  
5.02  
0
0
E
0
10.88  
5.59  
0
B
0
C
4.99  
0
4.01  
0
E
0
B0  
C
0
0
0.68  
5.02  
0
5
E
0
B0  
0
15  
WAVEFORMS  
(1) I101 PIN 19  
(2) I101 PIN 20  
(3) I101 PIN 21  
(5) I101 PIN 40  
(7) I101 PIN 46  
(4) I101 PIN 23  
(5) I101 PIN 44  
(8) I301 PIN7  
16  
WAVEFORMS  
(9) I701 PIN 7  
(10) I701 PIN 17  
(12) I801 PIN 2  
1) I701 PIN 18  
(13) T402 PIN 25.5V  
(14) T402 PIN 10.5V  
(15) T402 PIN HEATER  
(16) T402 PIN 200V  
17  
WAVEFORMS  
(17) T401 PIN H.V.  
(18) T801 PIN 133V  
(19) Q403 COLLECTOR  
(20) CRT SOCKET PIN B  
(21) CRT SOCKET PIN R  
(22) CRT SOCKET PIN G  
18  
SCHEMATIC DIAGRAM  
19  
EXPLODED VIEW  
1. DTQ-14V1FSN  
20  
EXPLODED VIEW  
2. DTQ-14V3FSN  
21  
EXPLODED VIEW  
3. DTQ-14V5FCN / FSN  
22  
EXPLODED VIEW  
4. DTQ-14U1FSN  
23  
EXPLODED VIEW  
5. DTQ-20V1FSN  
24  
EXPLODED VIEW  
6. DTQ-20V3FSN  
25  
EXPLODED VIEW  
7. DTQ-20V4FSN  
26  
EXPLODED VIEW  
8. DTQ-20U1FSN  
27  
ELECTRICAL PARTS LIST  
CAUTION  
I“ is a safety part, so it must be used the same part.  
2” is a recommendable part for essential stock.  
LOC  
PART CODE  
PART NAME  
DESCRIPTION  
REMARK  
LOC  
40  
PART CODE  
PART NAME  
FLUX SOLVENT  
DESCRIPTION  
REMARK  
ZZ100  
ZZ110  
10  
48B4343A01  
PTACPWH394  
4850A02510  
4850Q00810  
4850A00250  
4.86E+09  
TRANSMITTER REMOCON R-43A01 (AA)  
2291050301  
2291140501  
2TP07545CL  
2291051001  
2291130215  
CCYB2H103K  
CMYH3C722H  
CMYE2D434J  
CL1UC3104M  
CMYH3C332J  
CEYN2D331P  
CH1BFE472M  
CH1BFE472M  
DLH2PR----  
DPBS208GUF  
5F1GB4021L  
1DCT814B--  
PTC2SW7101  
1LA7841---  
IM-1000  
ACCESSORY AS  
ANT ROD  
DTQ-14P2FC  
50  
WAX COVER  
TAPE OPP  
S3BW216B (L=600 MM)  
R6P/LN  
80  
45X50 CLEAR  
30  
BATTERY  
90  
FLUX KILLER  
GREASE SILICON  
C CERA  
KFT-7  
40  
TRANS ANT MATCHING  
MANUAL INSTRUCTION  
BAG INSTRUCTION  
COVER BACK AS  
COVER BACK  
CLOTH BLACK  
PACKING AS  
IMT-06  
100  
G-600  
10000  
M821  
ZZ120  
M211  
M211B  
ZZ130  
10  
DTQ-20V1FS  
C403  
C404  
C406  
C801  
C802  
C804  
C881  
C882  
D703  
D801  
F801  
I101  
500V B 0.01MF K  
1.6KV BUP 7200PF H  
200V PU 0.43MF J  
WORLD AC250V 0.1UF M R.47  
1.6KV BUP 3300PF J  
200V LHS 330MF  
AC400V 4700PF M U/C/V  
AC400V 4700PF M U/C/V  
LH-2P-R  
4858213800  
PTBCSHH488  
4852151400  
4857817640  
PTPKCPH488  
6520010100  
485803871D  
4858186700  
4858210600  
58G0000078  
48519A4710  
PTCACAH488  
PTRTPWH394  
58D0000082  
2233030001  
2TC26019BE  
2224050026  
4850PM001-  
48A96R004-  
48A96314C3  
4851931800  
4856013350  
4856215402  
7172401412  
4853214800  
4855415800  
4855613600  
4856013351  
4856812001  
7178301011  
PTFMSJH488  
4852067200  
PTSPPWH407  
4850703S50  
4858314010  
L.D.P.E T0.05X250X400  
DTQ-14V1FCN  
FR HIPS BK  
C MYLAR  
C MYLAR  
C LINE ACROSS  
C MYLAR  
FELT 100X20X0.7  
DTQ-14V1FCN  
18M/M J D O  
C ELECTRO  
C CERA AC  
C CERA AC  
LED BLOCK  
DIODE BRIDGE  
FUSE GLASS TUBE  
IC CHROMA  
HEAT SINK ASS‘Y  
IC VERTICAL  
HEAT SINK  
STAPLE PIN  
I
I
M801  
M811  
M821  
ZZ131  
ZZ132  
ZZ140  
CRT1  
V01  
BOX CARTON  
PAD  
SW-2  
EPS 14V1  
BAG P.E  
L.D.P.E T0.03X1000X900  
DC-1400  
PBS208GU-CA (FORMING)  
UL/CSA TL 4A 125V MF51  
DCT814B  
COIL DEGAUSSING  
CRT GROUND NET  
CABINET AS  
2
2
I
1401S-1015-1P  
DTQ-14V1FCN  
"NTSC 14"" ITC CRT AS"  
ODY-M1489  
I301  
1LA7841--- + 7174300811  
LA7841  
CRT AS  
2
I
I301  
2
COIL DY  
I
I301A  
I301B  
I401  
4857027101  
7174300811  
1K1A7805P1  
1TDA7267--  
1DW8634NA1  
124LC04B--  
1MA8630---  
1LTV817C--  
1DP133----  
SPCC T1.0+SN  
TT2 RND 3X8 MFZN  
KIA7805API  
V02  
PAINT LOCK  
760G  
SCREW TAPPTITE  
IC REGULATOR  
IC AUDIO AMP  
IC MICOM  
V03  
TAPE CLOTH  
BOND SILICON  
MAGNET CP  
19X30 BEIGE  
V04  
RTV 122 CARTRIDGE  
NY-225 (MINI NECK)  
HMR 28 SR (|0X54)  
A34KQV42X  
I601  
TDA7267  
2
2
2
2
V05  
I701  
DW863432V-NA1  
24LC04B  
V06  
RUBBER WEDGE  
CRT BARE  
I703  
IC MEMORY  
IC POWER  
V901  
M191  
M201A  
M201B  
M211A  
M321  
M541  
M561  
M601  
M681  
SP01A  
ZZ200  
M201  
ZZ202  
PA601  
SP01  
ZZ290  
10  
I801  
MA8630  
I
BUTTON CTRL  
SCREW CRT FIXING  
WASHER RUBBER  
SCREW TAPPTITE  
BRKT  
4939100+5536001  
25X80 BK  
I802  
IC PHOTO COUPLER  
IC ERROR AMP  
IC PREAMP  
JACK PIN BOARD  
JACK PIN BOARD  
COIL CHOKE  
COIL VCO  
LTV-817C  
I803  
DP133  
2
CR T2.0  
IL701  
JP02  
JP03  
L111  
L501  
L801  
M681  
P401  
P501  
PWC1  
Q402  
Q902  
Q903  
Q904  
R801  
R881  
RLY1  
1KRT30----  
KRT30  
TT2 TRS 4X14 MFZN BK  
FR HIPS BK  
4859109950  
4859109150  
58C5580019  
58N0000042  
5PLF24A1--  
4856812001  
4859240020  
4850708N11  
4859907910  
TKSC5386--  
TKTC3229--  
TKTC3229--  
TKTC3229--  
RX07C229JF  
DEC7R0M140  
5SC0101338  
PH-JB-9710A  
PH-JB-9615C  
SPEC PLATE  
150ART P/E FILM (C/TV)  
COPPER T0.4  
25X140 YL  
TRF-9225 (0.55UH)  
TRF-V008  
MARK BRAND  
SCREW CRT FIXING  
TIE CABLE  
FILTER LINE  
TIE CABLE  
LF-24A1  
I
NYLON66 DA100  
TT2 WAS 3X10 MFZN  
DTQ-14V1FCN  
FR HIPS BK  
NYLON66 DA100  
YFW500-05  
SCREW TAPPTITE  
MASK FRONT AS  
MASK FRONT  
SPEAKER AS  
CONNECTOR  
SPEAKER  
CONN WAFER  
CONNECTOR  
CORD POWER AS  
TR  
BIC-08T-25T+C-20T+ULW=300  
ME301P+TER=1830  
KSC5386  
2
2
I
DTQ-14J4FC  
YH025-03+35098+ULW=200  
SP-5070F01 3W 8 OHM  
DTQ-14V1FCN  
S62S-PB37-SB1  
RS 60-1.2 1.6A  
DF-2012U  
TR  
KTC 3229  
2
2
TR  
KTC 3229  
PTMPMSH488 PCB MAIN MANUAL AS  
TR  
KTC 3229  
2193100710  
2193011101  
2291050615  
SOLDER POWER BAR  
SOLDER WIRE  
R CEMENT  
7W 2.2 0HM J 15MM 4P  
ECPAC7R0M140  
DQ5D1-O(M)/GJ-SS-105LM  
20  
POSISTOR  
30  
FLUX SOLDER  
SW RELAY  
I
28  
ELECTRICAL PARTS LIST  
LOC  
PART CODE  
PART NAME  
VARISTOR  
DESCRIPTION  
SVC471D14A  
REMARK  
LOC  
PART CODE  
PART NAME  
DESCRIPTION  
1/10 0 OHM 2012  
REMARK  
RS801  
SCT1  
DSVC471D14  
4859303930  
I
JC703  
JC704  
RC105  
RC150  
RC151  
RC154  
RC156  
RC223  
RC224  
RC225  
RC226  
RC228  
RC229  
RC451  
RC452  
RC453  
RC454  
RC455  
RC503  
RC508  
RC509  
RC510  
RC511  
RC525  
RC526  
RC530  
RC531  
RC533  
RC541  
RC542  
RC548  
RC551  
RC556  
RC557  
RC558  
RC559  
RC561  
RC562  
RC565  
RC566  
RC567  
RC568  
RC570  
RC572  
RC573  
RC576  
RC577  
RC629  
RC630  
HRFT000-CA  
HRFT000-CA  
HRFT153JCA  
HRFT153JCA  
HRFT104JCA  
HRFT473JCA  
HRFT473JCA  
HRFT224JCA  
HRFT224JCA  
HRFT392JCA  
HRFT101JCA  
HRFT103JCA  
HRFT750JCA  
HRFT153JCA  
HRFT113JCA  
HRFT103JCA  
HRFT102JCA  
HRFT331JCA  
HRFT752JCA  
HRFT102JCA  
HRFT102JCA  
HRFT561JCA  
HRFT822JCA  
HRFT102JCA  
HRFT102JCA  
HRFT561JCA  
HRFT561JCA  
HRFT390JCA  
HRFT682JCA  
HRFT332JCA  
HRFT824JCA  
HRFT121JCA  
HRFT000-CA  
HRFT182JCA  
HRFT103JCA  
HRFT331JCA  
HRFT561JCA  
HRFT914JCA  
HRFT123JCA  
HRFT123JCA  
HRFT103JCA  
HRFT472FCA  
HRFT103JCA  
HRFT223JCA  
HRFT102JCA  
HRFT000-CA  
HRFT201JCA  
HRFT102JCA  
HRFT104JCA  
R CHIP  
R CHIP  
R CHIP  
R CHIP  
R CHIP  
R CHIP  
R CHIP  
R CHIP  
R CHIP  
R CHIP  
R CHIP  
R CHIP  
R CHIP  
R CHIP  
R CHIP  
R CHIP  
R CHIP  
R CHIP  
R CHIP  
R CHIP  
R CHIP  
R CHIP  
R CHIP  
R CHIP  
R CHIP  
R CHIP  
R CHIP  
R CHIP  
R CHIP  
R CHIP  
R CHIP  
R CHIP  
R CHIP  
R CHIP  
R CHIP  
R CHIP  
R CHIP  
R CHIP  
R CHIP  
R CHIP  
R CHIP  
R CHIP  
R CHIP  
R CHIP  
R CHIP  
R CHIP  
R CHIP  
R CHIP  
R CHIP  
SOCKET CRT  
FILTER SAW  
ISMG03S INCHANG  
TSF5241P  
2
I
1/10 0 OHM 2012  
SF101  
T401  
5PTSF5241P  
50D10A3---  
1/10 15K OHM J 2012  
1/10 15K OHM J 2012  
1/10 100K OHM J 2012  
1/10 47K OHM J 2012  
1/10 47K OHM J 2012  
1/10 220K OHM J 2012  
1/10 220K OHM J 2012  
1/10 3.9K OHM J 2012  
1/10 100 OHM J 2012  
1/10 10K OHM J 2012  
1/10 75 OHM J 2012  
1/10 15K OHM J 2012  
1/10 11K OHM J 2012  
1/10 10K OHM J 2012  
1/10 1K OHM J 2012  
1/10 330 OHM J 2012  
1/10 7.5K OHM J 2012  
1/10 1K OHM J 2012  
1/10 1K OHM J 2012  
1/10 560 OHM J 2012  
1/10 8.2K OHM J 2012  
1/10 1K OHM J 2012  
1/10 1K OHM J 2012  
1/10 560 OHM J 2012  
1/10 560 OHM J 2012  
1/10 39 OHM J 2012  
1/10 6.8K OHM J 2012  
1/10 3.3K OHM J 2012  
1/10 820K OHM J 2012  
1/10 120 OHM J 2012  
1/10 0 OHM 2012  
TRANS DRIVE  
FBT  
TD-10A3  
T402  
50H0000198  
50M3541T2-  
FSA37012M  
2
I
2
I
I
T801  
TRANS SMPS  
TUNER VARACTOR  
CRYSTAL QUARTZ  
FILTER CERA  
PCB CHIP MOUNT B AS  
C CHIP CERA  
C CHIP CERA  
C CHIP CERA  
C CHIP CERA  
C CHIP CERA  
C CHIP CERA  
C CHIP CERA  
C CHIP CERA  
TSM-3541T2  
U102  
4859719130  
DT5-NF20F  
X701  
5XYR03276C  
5PYXT4R5MB  
PTMPJ2H488  
HCBK103KCA  
HCBK103KCA  
HCBK103KCA  
HCBK103KCA  
HCBK103KCA  
HCBK102KCA  
HCQK101JCA  
HCQK101JCA  
C-001R 32.768000KHZ 20PPM  
XT 4.5MB  
Z501  
ZZ200  
CC151  
CC152  
CC153  
CC154  
CC155  
CC528  
CC551  
CC552  
CC556  
CC560  
CC562  
CC567  
CC568  
CC569  
CC570  
CC571  
CC573  
CC575  
CC580  
CC612  
CC662  
CC752  
CC753  
CC754  
CC755  
CC756  
CC757  
CC758  
CC759  
CC760  
CC768  
CC780  
CC796  
CC900  
CC902  
CC903  
CC904  
JC701  
JC702  
DTQ-14V1FCN  
50V X7R 0.01MF K 2012  
50V X7R 0.01MF K 2012  
50V X7R 0.01MF K 2012  
50V X7R 0.01MF K 2012  
50V X7R 0.01MF K 2012  
50V X7R 1000PF K 2012  
50V CH 100PF J 2012  
50V CH 100PF J 2012  
50V CH 8PF D 2012  
50V X7R 0.01MF K 2012  
50V CH 18PF J 2012  
50V CH 180PF J 2012  
50V X7R 0.01MF K 2012  
50V X7R 0.01MF K 2012  
50V Y5V 0.1MF Z 2012  
50V Y5V 0.1MF Z 2012  
50V Y5V 0.1MF Z 2012  
50V X7R 1000PF K 2012  
50V X7R 1500PF K 2012  
50V Y5V 0.1MF Z 2012  
50V X7R 0.015MF K 2012  
50V CH 18PF J 2012  
50V CH 18PF J 2012  
50V X7R 0.01MF K 2012  
50V X7R 0.01MF K 2012  
50V CH 220PF J 2012  
50V X7R 0.033MF K 2012  
50V CH 100PF J 2012  
50V CH 100PF J 2012  
50V CH 100PF J 2012  
50V CH 100PF J 2012  
50V X7R 0.01MF K 2012  
50V X7R 0.01MF K 2012  
50V X7R 1000PF K 2012  
50V CH 270PF J 2012  
50V CH 270PF J 2012  
50V CH 270PF J 2012  
1/10 0 OHM 2012  
HCQK809DCA C CHIP CERA  
HCBK103KCA  
HCQK180JCA  
HCQK181JCA  
HCBK103KCA  
HCBK103KCA  
HCFK104ZCA  
HCFK104ZCA  
HCFK104ZCA  
HCBK102KCA  
HCBK152KCA  
HCFK104ZCA  
HCBK153KCA  
HCQK180JCA  
HCQK180JCA  
HCBK103KCA  
HCBK103KCA  
HCQK221JCA  
HCBK333KCA  
HCQK101JCA  
HCQK101JCA  
HCQK101JCA  
HCQK101JCA  
HCBK103KCA  
HCBK103KCA  
HCBK102KCA  
HCQK271JCA  
HCQK271JCA  
HCQK271JCA  
HRFT000-CA  
HRFT000-CA  
C CHIP CERA  
C CHIP CERA  
C CHIP CERA  
C CHIP CERA  
C CHIP CERA  
C CHIP CERA  
C CHIP CERA  
C CHIP CERA  
C CHIP CERA  
C CHIP CERA  
C CHIP CERA  
C CHIP CERA  
C CHIP CERA  
C CHIP CERA  
C CHIP CERA  
C CHIP CERA  
C CHIP CERA  
C CHIP CERA  
C CHIP CERA  
C CHIP CERA  
C CHIP CERA  
C CHIP CERA  
C CHIP CERA  
C CHIP CERA  
C CHIP CERA  
C CHIP CERA  
C CHIP CERA  
C CHIP CERA  
R CHIP  
1/10 1.8K OHM J 2012  
1/10 10K OHM J 2012  
1/10 330 OHM J 2012  
1/10 560 OHM J 2012  
1/10 910KOHM J 2012  
1/10 12K OHM J 2012  
1/10 12K OHM J 2012  
1/10 10K OHM J 2012  
1/10 4.7K OHM F 2012  
1/10 10K OHM J 2012  
1/10 22K OHM J 2012  
1/10 1K OHM J 2012  
1/10 0 OHM 2012  
1/10 200 OHM J 2012  
1/10 1K OHM J 2012  
1/10 100K OHM J 2012  
R CHIP  
1/10 0 OHM 2012  
29  
ELECTRICAL PARTS LIST  
LOC  
PART CODE  
PART NAME  
DESCRIPTION  
REMARK  
LOC  
PART CODE  
PART NAME  
C ELECTRO  
DESCRIPTION  
REMARK  
RC655  
RC701  
RC704  
RC705  
RC706  
RC707  
RC731  
RC732  
RC733  
RC734  
RC735  
RC736  
RC737  
RC738  
RC750  
RC751  
RC752  
RC755  
RC756  
RC770  
RC775  
RC776  
RC778  
RC781  
RC782  
RC783  
RC784  
RC786  
RC787  
RC788  
RC791  
RC792  
RC793  
RC794  
RC799  
RC813  
RC862  
RC913  
RC914  
RC915  
RC917  
RC918  
RC919  
RC923  
RC924  
RC925  
ZZ200  
C105  
HRFT162JCA  
HRFT220JCA  
HRFT102JCA  
HRFT472JCA  
HRFT472JCA  
HRFT102JCA  
HRFT103JCA  
HRFT132JCA  
HRFT132JCA  
HRFT132JCA  
HRFT102JCA  
HRFT103JCA  
HRFT103JCA  
HRFT471JCA  
HRFT472JCA  
HRFT471JCA  
HRFT471JCA  
HRFT102JCA  
HRFT102JCA  
HRFT103JCA  
HRFT472JCA  
HRFT472JCA  
HRFT103JCA  
HRFT102JCA  
HRFT331JCA  
HRFT472JCA  
HRFT514JCA  
HRFT102JCA  
HRFT472JCA  
HRFT472JCA  
HRFT102JCA  
HRFT102JCA  
HRFT102JCA  
HRFT102JCA  
HRFT103JCA  
HRFT363JCA  
HRFT363JCA  
HRFT121JCA  
HRFT121JCA  
HRFT121JCA  
HRFT241JCA  
HRFT241JCA  
HRFT241JCA  
HRFT471JCA  
HRFT471JCA  
HRFT471JCA  
PTMPJ0H488  
CEXF1C471V  
CEXF1E102V  
R CHIP  
R CHIP  
R CHIP  
R CHIP  
R CHIP  
R CHIP  
R CHIP  
R CHIP  
R CHIP  
R CHIP  
R CHIP  
R CHIP  
R CHIP  
R CHIP  
R CHIP  
R CHIP  
R CHIP  
R CHIP  
R CHIP  
R CHIP  
R CHIP  
R CHIP  
R CHIP  
R CHIP  
R CHIP  
R CHIP  
R CHIP  
R CHIP  
R CHIP  
R CHIP  
R CHIP  
R CHIP  
R CHIP  
R CHIP  
R CHIP  
R CHIP  
R CHIP  
R CHIP  
R CHIP  
R CHIP  
R CHIP  
R CHIP  
R CHIP  
R CHIP  
R CHIP  
R CHIP  
1/10 1.6K OHM J 2012  
1/10 22 OHM J 2012  
1/10 1K OHM J 2012  
1/10 4.7K OHM J 2012  
1/10 4.7K OHM J 2012  
1/10 1K OHM J 2012  
1/10 10K OHM J 2012  
1/10 1.3K OHM J 2012  
1/10 1.3K OHM J 2012  
1/10 1.3K OHM J 2012  
1/10 1K OHM J 2012  
1/10 10K OHM J 2012  
1/10 10K OHM J 2012  
1/10 470 OHM J 2012  
1/10 4.7K OHM J 2012  
1/10 470 OHM J 2012  
1/10 470 OHM J 2012  
1/10 1K OHM J 2012  
1/10 1K OHM J 2012  
1/10 10K OHM J 2012  
1/10 4.7K OHM J 2012  
1/10 4.7K OHM J 2012  
1/10 10K OHM J 2012  
1/10 1K OHM J 2012  
1/10 330 OHM J 2012  
1/10 4.7K OHM J 2012  
1/10 510K OHM J 2012  
1/10 1K OHM J 2012  
1/10 4.7K OHM J 2012  
1/10 4.7K OHM J 2012  
1/10 1K OHM J 2012  
1/10 1K OHM J 2012  
1/10 1K OHM J 2012  
1/10 1K OHM J 2012  
1/10 10K OHM J 2012  
1/10 36K OHM J 2012  
1/10 36K OHM J 2012  
1/10 120 OHM J 2012  
1/10 120 OHM J 2012  
1/10 120 OHM J 2012  
1/10 240 OHM J 2012  
1/10 240 OHM J 2012  
1/10 240 OHM J 2012  
1/10 470 OHM J 2012  
1/10 470 OHM J 2012  
1/10 470 OHM J 2012  
DTQ-14V1FCN  
C410  
C414  
C415  
C502  
C510  
C514  
C602  
C646  
C812  
C813  
C814  
C820  
C912  
ZZ200  
10  
CEXF2E100V  
CEXF1V471V  
CEXF1C102V  
CEXF1C102V  
CEXF1C471V  
CEXF1C471V  
CEXF1C102V  
CEXF1C471V  
CEXF1C102V  
CCXB3A221K  
CEXF2C101V  
CEXF2C101V  
CCXB3D102K  
PTMPJBH488  
2TM18006BE  
D1N4937G--  
DRGP15J---  
D1N4937G--  
DZY160----  
250V RSS 10MF (10X20) TP  
35V RSS 470MF (10X20) TP  
16V RSS 1000MF (10X20) TP  
16V RSS 1000MF (10X20) TP  
16V RSS 470MF (10X12.5)TP  
16V RSS 470MF (10X12.5)TP  
16V RSS 1000MF (10X20) TP  
16V RSS 470MF (10X12.5)TP  
16V RSS 1000MF (10X20) TP  
1KV B 220PF K (TAPPING)  
160V RSS 100MF (16X25) TP  
160V RSS 100MF (16X25) TP  
2KV B 1000PF K (TAPPING)  
DTQ-14V1FCN  
C ELECTRO  
C ELECTRO  
C ELECTRO  
C ELECTRO  
C ELECTRO  
C ELECTRO  
C ELECTRO  
C ELECTRO  
C CERA  
C ELECTRO  
C ELECTRO  
C CERA  
PCB MAIN M-10 AS  
TAPE MASKING  
DIODE  
6.2X500  
D802  
D807  
D813  
D824  
E001  
E002  
E003  
E004  
E005  
E006  
E007  
E008  
E009  
E012  
E013  
E014  
E016  
E017  
E018  
E019  
E020  
E021  
E024  
E025  
E026  
E027  
E028  
E029  
E030  
E031  
E100  
E101  
E102  
E103  
1N4937G (TAPPING)  
RGP15J  
DIODE  
DIODE  
1N4937G (TAPPING)  
ZY160  
DIODE ZENER  
EYE LET  
4856310300  
4856310300  
4856310300  
4856310300  
4856310300  
4856310300  
4856310300  
4856310300  
4856310300  
4856310300  
4856310300  
4856310300  
4856310300  
4856310300  
4856310300  
4856310300  
4856310300  
4856310300  
4856310300  
4856310300  
4856310300  
4856310300  
4856310300  
4856310300  
4856310300  
4856310300  
4856310600  
4856310600  
4856310600  
4856310600  
BSR T0.2 (R1.6)  
EYE LET  
BSR T0.2 (R1.6)  
EYE LET  
BSR T0.2 (R1.6)  
EYE LET  
BSR T0.2 (R1.6)  
EYE LET  
BSR T0.2 (R1.6)  
EYE LET  
BSR T0.2 (R1.6)  
EYE LET  
BSR T0.2 (R1.6)  
EYE LET  
BSR T0.2 (R1.6)  
EYE LET  
BSR T0.2 (R1.6)  
EYE LET  
BSR T0.2 (R1.6)  
EYE LET  
BSR T0.2 (R1.6)  
EYE LET  
BSR T0.2 (R1.6)  
EYE LET  
BSR T0.2 (R1.6)  
EYE LET  
BSR T0.2 (R1.6)  
EYE LET  
BSR T0.2 (R1.6)  
EYE LET  
BSR T0.2 (R1.6)  
EYE LET  
BSR T0.2 (R1.6)  
EYE LET  
BSR T0.2 (R1.6)  
EYE LET  
BSR T0.2 (R1.6)  
EYE LET  
BSR T0.2 (R1.6)  
EYE LET  
BSR T0.2 (R1.6)  
EYE LET  
BSR T0.2 (R1.6)  
EYE LET  
BSR T0.2 (R1.6)  
EYE LET  
BSR T0.2 (R1.6)  
EYE LET  
BSR T0.2 (R1.6)  
EYE LET  
BSR T0.2 (R1.6)  
EYE LET  
BSR T0.2 (R2.3)  
PCB MAIN (RHU) AS  
C ELECTRO  
EYE LET  
BSR T0.2 (R2.3)  
16V RSS 470MF (10X12.5)TP  
25V RSS 1000MF (13X20) TP  
EYE LET  
BSR T0.2 (R2.3)  
C310  
C ELECTRO  
EYE LET  
BSR T0.2 (R2.3)  
30  
ELECTRICAL PARTS LIST  
LOC  
PART CODE  
PART NAME  
EYE LET  
DESCRIPTION  
BSR T0.2 (R2.3)  
REMARK  
LOC  
PART CODE  
PART NAME  
C MYLAR  
DESCRIPTION  
100V 0.22MF J  
REMARK  
E104  
E105  
E106  
E107  
E108  
E109  
E110  
E111  
E114  
E115  
E116  
E117  
L807  
L811  
L841  
P601  
P801A  
P801B  
R601  
R814  
ZZ200  
C101  
C102  
C103  
C104  
C106  
C107  
C212  
C235  
C301  
C302  
C303  
C305  
C307  
C308  
C311  
C401  
C405  
C408  
C411  
C412  
C413  
C416  
C417  
C418  
C451  
C452  
C501  
C507  
4856310600  
4856310600  
4856310600  
4856310600  
4856310600  
4856310600  
4856310600  
4856310600  
4856310600  
4856310600  
4856310600  
4856310600  
5MC0000100  
5MC0000100  
5MC0000100  
485923162S  
4857417500  
4857417500  
RF01Z688K-  
RS02Z828JS  
PTMPJRH488  
CEXF1H109V  
CEXF1C101V  
CEXF1H339V  
CMXM2A333J  
CEXF1H109V  
CEXF1H228V  
CEXF1H100V  
CEXD1H229F  
CMXM2A103J  
CEXF1H479V  
CEXF1H100V  
CEXF1H101V  
CXSL2H100D  
CMXM2A104J  
CEXD1H229Q  
CCXB2H102K  
CEXF2C109V  
CEXF1C470V  
CEXF1H100V  
CCXB2H102K  
CCXB2H102K  
CCXB2H102K  
CCXB2H102K  
CMXM2A104J  
CEXF1C101V  
CEXF1C221V  
CMXL1H105J  
CMXM2A224J  
C508  
C509  
C511  
C512  
C513  
C516  
C517  
C518  
C519  
C520  
C525  
C555  
C575  
C601  
C603  
C604  
C634  
C701  
C702  
C703  
C704  
C705  
C780  
C807  
C809  
C810  
C811  
C818  
C819  
C845  
C850  
C876  
F801A  
F801B  
L601  
L805  
L901  
Q201  
Q401  
Q403  
Q404  
Q570  
Q575  
Q701  
Q702  
Q703  
Q704  
Q707  
Q804  
CMXM2A224J  
CEXF1H109V  
CMXM2A333J  
CEXF1H108V  
CEXF1H109V  
CEXF1H229V  
CMXM2A473J  
CEXF1H478V  
CEXF1H478V  
CEXF1H109V  
CEXF1H109V  
CEXF1H109V  
CEXF1E101V  
CMXM2A103J  
CEXF1H108V  
CEXF1H470V  
CEXF1H479V  
CEXF1H470V  
CEXF1C221V  
CEXF1H109V  
CEXF1H229V  
CEXF1H109V  
CEXF1H109V  
CMXM2A103J  
CMXM2A102J  
CCXB2H222K  
CCXB2H222K  
CEXF1C101V  
CEXF1H479V  
CEXF2A100V  
CMXM2A104J  
CEXF1C101V  
4857415001  
EYE LET  
BSR T0.2 (R2.3)  
C ELECTRO  
C MYLAR  
C ELECTRO  
C ELECTRO  
C ELECTRO  
C MYLAR  
C ELECTRO  
C ELECTRO  
C ELECTRO  
C ELECTRO  
C ELECTRO  
C ELECTRO  
C MYLAR  
C ELECTRO  
C ELECTRO  
C ELECTRO  
C ELECTRO  
C ELECTRO  
C ELECTRO  
C ELECTRO  
C ELECTRO  
C ELECTRO  
C MYLAR  
C MYLAR  
C CERA  
50V RSS 1MF (5X11) TP  
100V 0.033MF J (TP)  
EYE LET  
BSR T0.2 (R2.3)  
EYE LET  
BSR T0.2 (R2.3)  
50V RSS 0.1MF (5X11) TP  
50V RSS 1MF (5X11) TP  
50V RSS 2.2MF (5X11) TP  
100V 0.047MF J (TP)  
EYE LET  
BSR T0.2 (R2.3)  
EYE LET  
BSR T0.2 (R2.3)  
EYE LET  
BSR T0.2 (R2.3)  
EYE LET  
BSR T0.2 (R2.3)  
50V RSS 0.47MF (5X11) TP  
50V RSS 0.47MF (5X11) TP  
50V RSS 1MF (5X11) TP  
50V RSS 1MF (5X11) TP  
50V RSS 1MF (5X11) TP  
25V RSS 100MF (6.3X11) TP  
100V 0.01MF J (TP)  
EYE LET  
BSR T0.2 (R2.3)  
EYE LET  
BSR T0.2 (R2.3)  
EYE LET  
BSR T0.2 (R2.3)  
EYE LET  
BSR T0.2 (R2.3)  
COIL BEAD  
COIL BEAD  
COIL BEAD  
CONN WAFER  
TERM PIN  
TERM PIN  
R FUSIBLE  
R M-OXIDE FILM  
PCB MAIN RADIAL AS  
C ELECTRO  
C ELECTRO  
C ELECTRO  
C MYLAR  
HC-3550  
HC-3550  
HC-3550  
50V RSS 0.1MF (5X11) TP  
50V RSS 47MF (6.3X11) TP  
50V RSS 4.7MF (5X11) TP  
50V RSS 47MF (6.3X11) TP  
16V RSS 220MF (8X11.5) TP  
50V RSS 1MF (5X11) TP  
50V RSS 2.2MF (5X11) TP  
50V RSS 1MF (5X11) TP  
50V RSS 1MF (5X11) TP  
100V 0.01MF J (TP)  
YW025-03 (STICK)  
DA-IB0214(D2.3/DY PIN)  
DA-IB0214(D2.3/DY PIN)  
1W 0.68 OHM K (TAPPING)  
2W 0.82 OHM J SMALL  
DTQ-14V1FCN  
50V RSS 1MF (5X11) TP  
16V RSS 100MF (6.3X11) TP  
50V RSS 3.3MF (5X11) TP  
100V 0.033MF J (TP)  
50V RSS 1MF (5X11) TP  
50V RSS 0.22MF (5X11) TP  
50V RSS 10MF (5X11) TP  
50V RND 2.2MF (5X11) TP  
100V 0.01MF J (TP)  
100V 1000PF J (TP)  
C ELECTRO  
C ELECTRO  
C ELECTRO  
C ELECTRO  
C MYLAR  
500V B 2200PF K (TAPPING)  
500V B 2200PF K (TAPPING)  
16V RSS 100MF (6.3X11) TP  
50V RSS 4.7MF (5X11) TP  
100V RSS 10MF (6.3X11) TP  
100V 0.1MF J (TP)  
I
I
C CERA  
C ELECTRO  
C ELECTRO  
C ELECTRO  
C MYLAR  
C ELECTRO  
CLIP FUSE  
CLIP FUSE  
COIL CHOKE  
COIL CHOKE  
COIL PEAKING  
TR  
C ELECTRO  
C ELECTRO  
C ELECTRO  
C CERA  
50V RSS 4.7MF (5X11) TP  
50V RSS 10MF (5X11) TP  
50V RSS 100MF (8X11.5) TP  
500V SL 10PF D (TAPPING)  
100V 0.1MF J (TP)  
16V RSS 100MF (6.3X11) TP  
PFC5000-0702  
4857415001  
PFC5000-0702  
C MYLAR  
58CX430599  
58CX430599  
5CPX221J--  
AZ-9004Y 940K TP  
C ELECTRO  
C CERA  
50V RT 2.2MF (6.3X11) TP  
500V B 1000PF K (TAPPING)  
160V RSS 1MF (6.3X11) TP  
16V RSS 47MF (5X11) TP  
50V RSS 10MF (5X11) TP  
500V B 1000PF K (TAPPING)  
500V B 1000PF K (TAPPING)  
500V B 1000PF K (TAPPING)  
500V B 1000PF K (TAPPING)  
100V 0.1MF J (TP)  
AZ-9004Y 940K TP  
220UH J (RADIAL)  
C ELECTRO  
C ELECTRO  
C ELECTRO  
C CERA  
TKSC945CY-  
TKSC2330Y-  
TKSC945CY-  
TKSC945CY-  
TKTA1266Y-  
TKTA1275Y-  
TKSC945CY-  
TKSC945CY-  
TKSC945CY-  
TKTA1266Y-  
TKSC945CY-  
TKTA1275Y-  
KSC 945C-Y (TAPPING)  
KSC2330Y (TP)  
TR  
TR  
KSC 945C-Y (TAPPING)  
KSC 945C-Y (TAPPING)  
KTA1266Y (TP)  
TR  
C CERA  
TR  
C CERA  
TR  
KTA1275Y (TP)  
C CERA  
TR  
KSC 945C-Y (TAPPING)  
KSC 945C-Y (TAPPING)  
KSC 945C-Y (TAPPING)  
KTA1266Y (TP)  
C MYLAR  
TR  
C ELECTRO  
C ELECTRO  
C MYLAR  
16V RSS 100MF (6.3X11) TP  
16V RSS 220MF (8X11.5) TP  
50V MEU 1MF J  
TR  
TR  
TR  
KSC 945C-Y (TAPPING)  
KTA1275Y (TP)  
C MYLAR  
100V 0.22MF J  
TR  
31  
ELECTRICAL PARTS LIST  
LOC  
PART CODE  
PART NAME  
DESCRIPTION  
KTC3205Y (TP)  
REMARK  
LOC  
PART CODE  
PART NAME  
DESCRIPTION  
1N4148 (TAPPING)  
REMARK  
Q805  
Q851  
R301  
R302  
R303  
R305  
R403  
R411  
R412  
R413  
R414  
R418  
R420  
R817  
R913  
R914  
R915  
SW701  
SW702  
SW703  
SW704  
SW705  
SW706  
X502  
ZZ200  
10  
TKTC3205Y-  
TKSC945CY-  
RN01B471JS  
RN01B471JS  
RN01B129JS  
RN01B331JS  
RN01B562JS  
RN01B229JS  
RN01B369JS  
RN01B229JS  
RN01B229JS  
RN02B150JS  
RN02B620JS  
RN01B471JS  
RN02B123JS  
RN02B123JS  
RN02B123JS  
5S50101090  
5S50101090  
5S50101090  
5S50101090  
5S50101090  
5S50101090  
5XEX3R579C  
PTMPJAH488  
2TM14006LB  
2TM10006LB  
4859813791  
DUZ33B----  
TR  
TR  
D701  
D704  
D790  
D812  
D841  
D851  
J001  
J002  
J009  
J025  
J050  
J057  
J113  
J114  
J501  
J511  
J533  
J551  
J601  
J602  
J705  
J709  
J711  
J717  
J719  
J722  
J727  
J731  
J735  
J747  
J748  
J750  
J758  
J801  
J811  
J888  
J922  
J923  
J925  
J926  
J927  
J928  
J933  
J938  
J939  
J941  
J942  
J946  
J950  
D1N4148---  
DIODE  
KSC 945C-Y (TAPPING)  
1W 470 OHM J SMALL  
1W 470 OHM J SMALL  
1W 1.2 OHM J SMALL  
1W 330 OHM J SMALL  
1W 5.6K OHM J SMALL  
1W 2.2 OHM J SMALL  
1W 3.6 OHM J SMALL  
1W 2.2 OHM J SMALL  
1W 2.2 OHM J SMALL  
2W 15 OHM J SMALL  
2W 62 OHM J SMALL  
1W 470 OHM J SMALL  
2W 12K OHM J SMALL  
2W 12K OHM J SMALL  
2W 12K OHM J SMALL  
THVH472GCA  
DUZ3R9B---  
D1N4148---  
DIODE ZENER  
DIODE  
UZ-3.9B  
R METAL FILM  
R METAL FILM  
R METAL FILM  
R METAL FILM  
R METAL FILM  
R METAL FILM  
R METAL FILM  
R METAL FILM  
R METAL FILM  
R METAL FILM  
R METAL FILM  
R METAL FILM  
R METAL FILM  
R METAL FILM  
R METAL FILM  
SW TACT  
1N4148 (TAPPING)  
DUZ5R6BM--  
D1N4937G--  
DUZ8R2BM--  
85801065GY  
85801065GY  
85801065GY  
85801065GY  
85801065GY  
85801065GY  
85801065GY  
85801065GY  
85801065GY  
85801065GY  
85801065GY  
85801065GY  
85801065GY  
85801065GY  
85801065GY  
85801065GY  
85801065GY  
85801065GY  
85801065GY  
85801065GY  
85801065GY  
85801065GY  
85801065GY  
85801065GY  
85801065GY  
85801065GY  
85801065GY  
85801065GY  
85801065GY  
85801065GY  
85801065GY  
85801065GY  
85801065GY  
85801065GY  
85801065GY  
85801065GY  
85801065GY  
85801065GY  
85801065GY  
85801065GY  
85801065GY  
85801065GY  
85801065GY  
DIODE ZENER  
DIODE  
UZ-5.6BM  
1N4937G (TAPPING)  
DIODE ZENER  
WIRE COPPER  
WIRE COPPER  
WIRE COPPER  
WIRE COPPER  
WIRE COPPER  
WIRE COPPER  
WIRE COPPER  
WIRE COPPER  
WIRE COPPER  
WIRE COPPER  
WIRE COPPER  
WIRE COPPER  
WIRE COPPER  
WIRE COPPER  
WIRE COPPER  
WIRE COPPER  
WIRE COPPER  
WIRE COPPER  
WIRE COPPER  
WIRE COPPER  
WIRE COPPER  
WIRE COPPER  
WIRE COPPER  
WIRE COPPER  
WIRE COPPER  
WIRE COPPER  
WIRE COPPER  
WIRE COPPER  
WIRE COPPER  
WIRE COPPER  
WIRE COPPER  
WIRE COPPER  
WIRE COPPER  
WIRE COPPER  
WIRE COPPER  
WIRE COPPER  
WIRE COPPER  
WIRE COPPER  
WIRE COPPER  
WIRE COPPER  
WIRE COPPER  
WIRE COPPER  
WIRE COPPER  
UZ-8.2B  
AWG22 1/0.65 TIN COATING  
AWG22 1/0.65 TIN COATING  
AWG22 1/0.65 TIN COATING  
AWG22 1/0.65 TIN COATING  
AWG22 1/0.65 TIN COATING  
AWG22 1/0.65 TIN COATING  
AWG22 1/0.65 TIN COATING  
AWG22 1/0.65 TIN COATING  
AWG22 1/0.65 TIN COATING  
AWG22 1/0.65 TIN COATING  
AWG22 1/0.65 TIN COATING  
AWG22 1/0.65 TIN COATING  
AWG22 1/0.65 TIN COATING  
AWG22 1/0.65 TIN COATING  
AWG22 1/0.65 TIN COATING  
AWG22 1/0.65 TIN COATING  
AWG22 1/0.65 TIN COATING  
AWG22 1/0.65 TIN COATING  
AWG22 1/0.65 TIN COATING  
AWG22 1/0.65 TIN COATING  
AWG22 1/0.65 TIN COATING  
AWG22 1/0.65 TIN COATING  
AWG22 1/0.65 TIN COATING  
AWG22 1/0.65 TIN COATING  
AWG22 1/0.65 TIN COATING  
AWG22 1/0.65 TIN COATING  
AWG22 1/0.65 TIN COATING  
AWG22 1/0.65 TIN COATING  
AWG22 1/0.65 TIN COATING  
AWG22 1/0.65 TIN COATING  
AWG22 1/0.65 TIN COATING  
AWG22 1/0.65 TIN COATING  
AWG22 1/0.65 TIN COATING  
AWG22 1/0.65 TIN COATING  
AWG22 1/0.65 TIN COATING  
AWG22 1/0.65 TIN COATING  
AWG22 1/0.65 TIN COATING  
AWG22 1/0.65 TIN COATING  
AWG22 1/0.65 TIN COATING  
AWG22 1/0.65 TIN COATING  
AWG22 1/0.65 TIN COATING  
AWG22 1/0.65 TIN COATING  
AWG22 1/0.65 TIN COATING  
SW TACT  
THVH472GCA  
SW TACT  
THVH472GCA  
SW TACT  
THVH472GCA  
SW TACT  
THVH472GCA  
SW TACT  
THVH472GCA  
CRYSTAL QUARTZ  
PCB MAIN AXIAL AS  
TAPE MASKING  
TAPE MASKING  
PCB MAIN  
HC-49U 3.579545M (TP)  
DTQ-14V1FCN  
3M #232 6.0X2000M  
3M #232-MAP-C 6.2X2000M  
246X246 S1B  
20  
A001  
D101  
D221  
D301  
D311  
D312  
D401  
D405  
D406  
D407  
D408  
D409  
D501  
D502  
D503  
D504  
D505  
D541  
D571  
D572  
D573  
D574  
DIODE ZENER  
DIODE  
UZ-33B  
D1N4148---  
1N4148 (TAPPING)  
1N4004S  
D1N4004S--  
DBZX55C62-  
85801065GY  
D1N4937G--  
D1N4937G--  
D1N4937G--  
D1N4937G--  
D1N4937G--  
D1N4148---  
DIODE  
DIODE ZENER  
WIRE COPPER  
DIODE  
BZX55C-62  
AWG22 1/0.65 TIN COATING  
1N4937G (TAPPING)  
1N4937G (TAPPING)  
1N4937G (TAPPING)  
1N4937G (TAPPING)  
1N4937G (TAPPING)  
1N4148 (TAPPING)  
1N4148 (TAPPING)  
1N4148 (TAPPING)  
UZ-9.1BM  
DIODE  
DIODE  
DIODE  
DIODE  
DIODE  
D1N4148---  
DIODE  
D1N4148---  
DIODE  
DUZ9R1BM--  
D1N4148---  
DIODE ZENER  
DIODE  
1N4148 (TAPPING)  
UZ-9.1BM  
DUZ9R1BM--  
D1N4148---  
DIODE ZENER  
DIODE  
1N4148 (TAPPING)  
1N4148 (TAPPING)  
1N4148 (TAPPING)  
1N4148 (TAPPING)  
1N4148 (TAPPING)  
D1N4148---  
DIODE  
D1N4148---  
DIODE  
D1N4148---  
DIODE  
D1N4148---  
DIODE  
32  
ELECTRICAL PARTS LIST  
LOC  
J953  
PART CODE  
PART NAME  
WIRE COPPER  
DESCRIPTION  
REMARK  
LOC  
PART CODE  
PART NAME  
DESCRIPTION  
1/4 330 OHM J  
REMARK  
85801065GY  
85801065GY  
85801065GY  
85801065GY  
85801065GY  
85801065GY  
85801065GY  
85801065GY  
85801065GY  
85801065GY  
85801065GY  
85801065GY  
85801065GY  
5CPZ330K02  
5CPZ470K04  
5CPZ150K02  
5CPZ220K02  
RD-4Z472J-  
RD-4Z102J-  
RD-4Z682J-  
RN-4Z1603F  
RN-4Z1502F  
RD-4Z273J-  
RD-4Z333J-  
RD-4Z222J-  
RD-4Z113J-  
RD-4Z472J-  
RD-2Z751J-  
RD-2Z121J-  
RD-4Z302J-  
RD-2Z151J-  
RD-2Z151J-  
RD-4Z102J-  
RD-4Z152J-  
RD-4Z302J-  
RD-4Z102J-  
RD-4Z331J-  
AWG22 1/0.65 TIN COATING  
AWG22 1/0.65 TIN COATING  
AWG22 1/0.65 TIN COATING  
AWG22 1/0.65 TIN COATING  
AWG22 1/0.65 TIN COATING  
AWG22 1/0.65 TIN COATING  
AWG22 1/0.65 TIN COATING  
AWG22 1/0.65 TIN COATING  
AWG22 1/0.65 TIN COATING  
AWG22 1/0.65 TIN COATING  
AWG22 1/0.65 TIN COATING  
AWG22 1/0.65 TIN COATING  
AWG22 1/0.65 TIN COATING  
33UH K (AXIAL 3.5MM)  
47UH 10.5MM K (LAL04TB)  
15UH K (AXIAL 3.5MM)  
22UH K (AXIAL 3.5MM)  
1/4 4.7K OHM J  
R592  
R593  
R602  
R604  
R703  
R709  
R743  
R744  
R746  
R747  
R763  
R776  
R777  
R780  
R789  
R790  
R796  
R802  
R804  
R805  
R806  
R808  
R809  
R810  
R818  
R819  
R820  
R822  
R835  
R851  
R854  
R855  
R888  
R901  
R910  
R911  
R912  
RD-4Z331J-  
RD-4Z331J-  
RD-2Z271J-  
RD-4Z682J-  
RD-4Z101J-  
RD-4Z392J-  
RD-4Z472J-  
RD-4Z242J-  
RD-4Z752J-  
RD-4Z243J-  
RD-4Z201J-  
RD-4Z473J-  
RD-4Z102J-  
RD-4Z471J-  
RD-4Z102J-  
RD-4Z102J-  
RD-4Z472J-  
RD-4Z205J-  
RD-4Z201J-  
RD-4Z152J-  
RD-4Z562J-  
RD-4Z102J-  
RD-4Z102J-  
RD-4Z102J-  
RD-4Z135J-  
RD-4Z561J-  
RD-4Z392J-  
RD-4Z363J-  
RD-4Z114J-  
RD-4Z472J-  
85801065GY  
85801065GY  
RC-2Z565KP  
RD-4Z474J-  
RD-2Z332J-  
RD-2Z332J-  
RD-2Z332J-  
R CARBON FILM  
R CARBON FILM  
R CARBON FILM  
R CARBON FILM  
R CARBON FILM  
R CARBON FILM  
R CARBON FILM  
R CARBON FILM  
R CARBON FILM  
R CARBON FILM  
R CARBON FILM  
R CARBON FILM  
R CARBON FILM  
R CARBON FILM  
R CARBON FILM  
R CARBON FILM  
R CARBON FILM  
R CARBON FILM  
R CARBON FILM  
R CARBON FILM  
R CARBON FILM  
R CARBON FILM  
R CARBON FILM  
R CARBON FILM  
R CARBON FILM  
R CARBON FILM  
R CARBON FILM  
R CARBON FILM  
R CARBON FILM  
R CARBON FILM  
WIRE COPPER  
J954  
J955  
J956  
J957  
J959  
J963  
J964  
J965  
J966  
J967  
J970  
J977  
L112  
L502  
L533  
L701  
R165  
R227  
R351  
R352  
R353  
R359  
R360  
R361  
R362  
R401  
R405  
R416  
R417  
R501  
R502  
R554  
R569  
R570  
R579  
R591  
WIRE COPPER  
WIRE COPPER  
WIRE COPPER  
WIRE COPPER  
WIRE COPPER  
WIRE COPPER  
WIRE COPPER  
WIRE COPPER  
WIRE COPPER  
WIRE COPPER  
WIRE COPPER  
WIRE COPPER  
COIL PEAKING  
COIL PEAKING  
COIL PEAKING  
COIL PEAKING  
R CARBON FILM  
R CARBON FILM  
R CARBON FILM  
R METAL FILM  
R METAL FILM  
R CARBON FILM  
R CARBON FILM  
R CARBON FILM  
R CARBON FILM  
R CARBON FILM  
R CARBON FILM  
R CARBON FILM  
R CARBON FILM  
R CARBON FILM  
R CARBON FILM  
R CARBON FILM  
R CARBON FILM  
R CARBON FILM  
R CARBON FILM  
R CARBON FILM  
1/4 330 OHM J  
1/2 270 OHM J  
1/4 6.8K OHM J  
1/4 100 OHM J  
1/4 3.9K OHM J  
1/4 4.7K OHM J  
1/4 2.4K OHM J  
1/4 7.5K OHM J  
1/4 24K OHM J  
1/4 200 OHM J  
1/4 47K OHM J  
1/4 1K OHM J  
1/4 470 OHM J  
1/4 1K OHM J  
1/4 1K OHM J  
1/4 4.7K OHM J  
1/4 2M OHM J  
1/4 1K OHM J  
1/4 200 OHM J  
1/4 1.5K OHM J  
1/4 5.6K OHM J  
1/4 1K OHM J  
1/4 6.8K OHM J  
1/4 160K OHM F  
1/4 15K OHM F  
1/4 27K OHM J  
1/4 1K OHM J  
1/4 33K OHM J  
1/4 1K OHM J  
1/4 2.2K OHM J  
1/4 1.3M OHM J  
1/4 560 OHM J  
1/4 3.9K OHM J  
1/4 36K OHM J  
1/4 110K OHM J  
1/4 4.7K OHM J  
AWG22 1/0.65 TIN COATING  
AWG22 1/0.65 TIN COATING  
1/2 5.6M OHM K  
1/4 470K OHM J  
1/2 3.3K OHM J  
1/2 3.3K OHM J  
1/2 3.3K OHM J  
1/4 11K OHM J  
1/4 4.7K OHM J  
1/2 750 OHM J  
1/2 120 OHM J  
1/4 3K OHM J  
1/2 150 OHM J  
1/2 150 OHM J  
WIRE COPPER  
1/4 1K OHM J  
R CARBON COMP  
R CARBON FILM  
R CARBON FILM  
R CARBON FILM  
R CARBON FILM  
I
1/4 1.5K OHM J  
1/4 3K OHM J  
1/4 1K OHM J  
1/4 330 OHM J  
33  
DAEWOO ELECTRONICS CO., LTD  
686, AHYEON-DONG MAPO-GU  
SEOUL, KOREA  
C.P.O. BOX 8003 SEOUL, KOREA  
TELEX : DWELEC K28177-8  
CABLE : “DAEWOOELEC”  
E-mail : [email protected]  
FAX : 02) 360-7877  
TEL: 02) 360-7806  
Appendix  
IC DESCRIPTION  
U-COM(I701)  
X’TAL:32.768 KHz  
1
IC DESCRIPTION  
Appendix  
1. Abstract.  
This specification is 1-Tuner Mono Model for North/South America, CCD 1-Chip MICOM LC863228A.  
It is developing software specification for tuning only NTSC  
2. H/W Outline.  
1) ROM : 28,672 x 8bits.tsc  
: 15,872 x 8 bits for CGROM.  
2) RAM : 512 x 8bits.  
: 352 x 9bits.(for CRT Display)  
3) OSD Function.  
¡¤ Screen Display.  
¡¤ RAM  
: 36 characters x 16 lines.(by software)  
: 352 words. (9 bits per word)  
: 36 words. x 8 lines.  
Display area.  
1st control area. : 8 words. x 8 lines.  
¡¤ Characters.  
244 patterns programmable.  
Up to 244 kinds of 16 x 17 dot characters.  
Up to 244 kinds of 8 x 9 dot characters.  
or  
Up to 244 kinds of 16 x 32 dot characters used 16K bytes.  
¡¤ Various characters attributes.  
Character colors.  
: 16 colors  
Character background colors. : 16 colors  
Fringe / shadow colors.  
Full screen colors.  
Rounding.  
: 16 colors  
: 16 colors  
Underline.  
Italic character.(slanting)  
¡¤ Attribute can be changed without spacing.  
¡¤ Vertical display start line number can be set for each row independently.(Row can be overlapped.)  
¡¤ Horizontal display start position can be set for each row independently.  
¡¤ Different display modes can be set for each row independently.  
Caption and Text mode/ OSD mode 1/ OSD mode 2(Quarter size)/ Simplified graphic mode.  
¡¤ Ten character sizes.  
Horiz. x Vert. = (1x1),(1x2),(2x2),(2x4),(0.5x0.5)  
(1.5x1),(1.5x2),(3x2),(3x4),(0.75x0.5)  
¡¤ Shuttering and scrolling on each row.  
3. System Feature.  
1) The system for TV tuning is Frequency Synthesis type.  
2) Closed Captions function is interior designed.  
2
IC DESCRIPTION  
Appendix  
3) On Screen Displays function is interior designed.  
4) Package.  
: 36 PIN SDIP.  
2
5) Tuner (Pre-scaler.)  
: I C Bus.  
/PLL IC : TAU 6014-S(SIEMENS).  
6) Remocon.  
: The IC of Transmission (MITSUBISHI M50560)  
2
2
7) E PROM.  
: 24C04(I C Bus)  
à
Apply one byte Read/Write mode.  
8) 6-Local Key.  
9) Option S/W  
10) IF/V/C/D IC  
: A/D Input Control.(Power, Ch Up/Down, Vol Up/Down, Menu)  
: Port Input Option Check.  
:DTC814(LA79814)  
4. Function.  
1) C. C. D. function.  
- A section of C. C. D. operates FCC based specification.  
2) C. C. D. controlled function.  
- Closed Caption Mode. (Off<-->C1<-->C2<-->T1<-->T2<-->Off)  
- CC On Mute.(Off <-->C1<-->C2<-->Off)  
- Closed Caption is prior to CC On Mute.  
3) Tuning Function.  
2
- I C Bus.  
- PLL IC Interface.  
- FS 181 Channel (AIR 2-69CH, CABLE 1-125CH)  
- AFT Operation(Fine Tuning ) -2.5Fn+2.5MHz  
- AIR/CABLE (STD, HRC, IRC ). Only Cable 5,6CH is that AFT range is cover over  
broad-band. -2.5MHzFn+3.5MHz.  
.
- Memorize Channels.(If a channel is broadcasting, the channel is memorized.)  
- Direct Tuning(09KEY)  
- Channel Up/Down.(Memorized Channels) -> The Ch Up/Down buttons on the Remocon and on the front panel  
are same function.  
- Search Channel Up/Down.(If No-Memory or only 1CH is Memory)  
- Channel Memory.(ADD/DELETE)  
- Channel Review Function.  
- Last Channel Memory Function.  
4) OSD Function.  
- In Line(Video) Mode, Things(Items) that is concerned with Air and Cable disappear in the Menu.  
- Channel, AV display.  
- Small & Graphic ICON Menu.  
2
- Volume / Picture control --> I C Bus Control  
5) The Others Function.  
- Video/Audio Mute Function.  
- If a Channel is no signal, after 15 minutes is Auto-Power Off Function.  
3
IC DESCRIPTION  
Appendix  
- Auto Power On Function.(Power Restore function in the Special Menu)  
- Heat Run Function. --- OSD White Back-Ground  
- Sleep Timer.  
- Wake Up Time Function.  
- Off Time Function.  
- Remote Reception & Control.  
- Auto Tint.----------------------- (Option)  
- Power Restore.  
- Input(TV/Line) Controlled function. ----------------------- (Option)  
- Reception.(Air/Cable : Factory Initial Condition)  
- Blue Background.-----------------------------------------------(Option)  
- 3-Language (North America : ENG/SPA/FRA, South America : ENG/SPA/POR ).  
2
2
- E PROM Interface (I C Bus Control)  
- CH 6 TRAP Function.(IS-31 )  
- PLL IC Band Data.(Control Byte 2-->P3~P0)  
VHF L  
VHF H  
: 1  
: 2  
CH6 TRAP : 5 (IS-31) AIR(Cable) CH 6 Only  
UHF : 8  
5. The Table of Option and Schedule.  
Model Name  
Pin  
Option  
Auto Tint  
Application  
Reference  
- Low(DC_0V) : ON(Auto Tint)  
- High(DC_5V) : OFF  
- Low(DC_0V) : Blue Back  
- High(DC_5V) : No Blue Back  
- Low(DC_0V) :Normal  
- High(DC_5V) : Prison  
- Low(DC_0V) : Mono  
- High(DC_5V) :Stereo  
- No Use.  
CN - 001N  
#30  
O
#32  
#33  
#34  
Bule Back  
Prison  
O
O
O
X
Mono/Stereo  
#35  
#36  
Caption  
TV only  
- No Use.  
- Low(DC_0V) :TV/Video  
- High(DC_5V) :TV/Only  
- Use. (No Use.)  
O
6
Tatal Sun  
4
IC DESCRIPTION  
Appendix  
6. Pin Description  
PIN  
1
Terminal  
Name  
Explanation  
Remarks  
P10/SDA0 ROM Data Main  
IC Data  
6 bit input/output port  
Input/output can be Specified for each bit  
Other function.  
ROM CLK  
P11/SCLK0  
2
3
4
Main IC CLK  
P10 IIC0 data I/O  
P11 IIC0 clock output.  
P12 IIC1 data I/O  
P12/SDA1  
Tuner Data  
P13 IIC1 clock output.  
P13/SCLK1  
VSS  
Tuner CLK  
GND  
GND  
5
6
7
8
Negative power supply.  
XT1  
XT2  
It uses 32.768KHz X-TAL.  
10 pin is input terminal for crystal oscillator.  
11 pin is output terminal for crystal oscillator.  
XT1  
XT2  
+5V ( 0.5V)  
Positive power supply.  
VDD  
VDD  
9
Power, Ch up/down, Vol up/down, Menu  
P04/AN4  
P05/AN5  
KEY-IN  
AFT-IN  
Dc value that comes from the 10 pin of LA76810/14  
10  
Connect this port to AGC of Tuner  
Default Voltage : 3.75V  
Variable Voltage : 3.25V, 3.5V, 4.0V  
11  
12  
P06/AN6  
P07/AN7  
AGC-IN  
Use only japan Model.  
This port uses when is Stand - By status  
Condition : Input AC Power On  
Power off : High (DC 5V) Output. (Red)  
Power on : Low (DC 0V) Output.  
ST-BY(H)  
Reset terminal.  
Active Low  
13  
14  
/RES  
Filter  
/FES  
FILT  
Filter terminal for PLL  
Output terminal  
CVSB IN  
TV/VID  
/VS  
15  
16  
17  
CVIN  
P01  
/VS  
/HS  
R
Video signal input terminal  
TV Mode : High Line(Video) Mode : Low  
Vertical synchronization signal input terminal  
Horizental synchronization signal input terminal  
Red output terminal of RGB image  
18  
19  
20  
/HS  
R
Green output terminal of RGB image  
G
G
5
IC DESCRIPTION  
Appendix  
PIN  
21  
Terminal  
B
Name  
B
Explanation  
Blue output terminal of RGB image  
Fast blanking control signal  
Switch TV image Signal and caption / OSD image signal  
Output terminal  
22  
23  
24  
BL  
P31  
P32  
BL  
Audio Mute  
Power On  
Use only read data of LA76814/10  
Use when does power off/on  
Power off: Output Low(DC 0V)  
Power on: Output High(DC 5V)  
25  
26  
27  
28  
P70/INT0  
P71/INT1  
P72/INT2  
P73/INT3  
Bus Stop  
No Use  
Relay On/Off  
A/V Detection  
Remocon In  
Relay On/Off Terminal  
Detect port of Front A/V  
Input of Remocon Signal  
High: RF only mode  
Low: RF/AV mode  
29  
P14/PWM1  
P15/PWM2  
RF(H)/AV(L)  
AUTO TINT  
Low (DC-0V) : On(Auto Tint)  
High (DC-5V) : Off  
30  
31  
32  
Use only to control Sound of Stereo mode  
P16/PWM3 PWM VOLUME  
High (DC-5V) : No Blue Back  
Low (DC-0V) : Blue Back  
P17  
P00  
BLUE BACK  
PRISON  
Low (DC-0V) : Normal  
High (DC-5V) : Prison  
33  
Low (DC-0V) : Mono  
High (DC-5V) : Stereo  
34  
35  
36  
P01  
P02  
P03  
MONO/STEREO  
CAPTION  
No Use  
Low (DC-0V) : TV/Video  
High (DC-5V) : TV Only  
TV ONLY(H)  
Output form and existence of pull- up resistor for every port can be specified for each bit.  
At port 1, Programable pull- up resistor provided when specifing either COOS or N- ch open drain output.  
Port status in reset.  
Teriminal  
Port 0  
I/O  
Pull- up resistor status at selection pull- up option.  
Pull- up resistor OFF, ON after reset release.  
Programmable pull- resistor OFF.  
I
I
Port 1  
6
IC DESCRIPTION  
Appendix  
I101  
DCT814(LA76814) : IC VIDEO PROCESSOR  
1
54  
53  
52  
51  
50  
49  
48  
47  
46  
45  
44  
43  
42  
41  
40  
39  
38  
37  
36  
35  
34  
33  
32  
31  
30  
29  
28  
AUDIO OUT  
FM OUTPUT  
SIF INPUT  
2
SIF APC FILTER  
SIF OUTPUT  
3
PIF AGC  
4
RF AGC OUT  
EXT. AUDIO INPUT  
VCO FILTER  
5
PIF INPUT1  
6
PIF INPUT2  
VCO COIL1  
7
IF GND  
VCO COIL2  
8
IF VCC  
APC FILTER  
9
FM FILTER  
VIDEO OUTPUT  
10  
11  
12  
13  
14  
15  
16  
17  
18  
19  
20  
21  
22  
23  
24  
25  
26  
27  
AFT OUTPUT  
BUS DATA  
BLACK LEVEL DETECTOR  
INT. VIDEO INPUT(S-C IN)  
VIDEO/VER. VCC  
EX. VIDEO INPUT(Y IN)  
VIDEO/VER./BUS GND  
VIDEO OUTPUT  
BUS CLOCK  
ABL IN  
OSD RED INPUT  
OSD GREEN INPUT  
OSD BLUE INPUT  
FAST BLANKING INPUT  
RGB VCC  
CHROMA AFC1 FILTER  
3.58 CRYSTAL  
fsc OUTPUT  
RED OUTPUT  
GREEN OUTPUT  
BLUE OUTPUT  
B.AKB INPUT  
VERTICAL OUTPUT  
RAMP ALC FILTER  
HOR./BUS VCC  
HOR. AFC FILTER  
HORIZONTAL OUTPUT  
CHROMA AFC2 FILTER  
X-RAY INPUT  
CCD/HOR. GND  
CCD FILTER  
CCD VCC  
CLOCK(4MHz) OUTPUT  
VCO IREF  
FBP INPUT  
7
Appendix  
TROUBLESHOOTING GUIDE  
1. NO POWER  
8
TROUBLESHOOTING GUIDE  
Appendix  
2. NO PICTURE  
NG : GO to the figure c  
OK : Go the figure d  
Check the waveform of I101 #46  
1701  
MICOM  
9
TROUBLESHOOTING GUIDE  
Appendix  
3. NO SOUND  
NG : Go to the figure e  
OK : Go to the figure f g  
Check audio output signal of I101 #1  
1701  
MICOM  
10  
TROUBLESHOOTING GUIDE  
Appendix  
4. CH DON’T STOP  
NG : Loss of signal or weak signal  
OK : Go to the figure h  
Check the input signal conditions  
11  
TROUBLESHOOTING GUIDE  
Appendix  
5. NO COLOR  
6. NO VERTICAL DEFLECTION  
12  
TROUBLESHOOTING GUIDE  
Appendix  
7. NO ON-SCREEN DISPLAY  
8. REMOTE CONTROL DOES NOT OPERATE  
13  

HP Hewlett Packard HP Pavilion 20xi 20 C4D33AA#ABA User Manual
HP Hewlett Packard Hewlett Packard Computer Monitor L1945W User Manual
GE 28041xx1 User Manual
Fisher Paykel Sol X CT560 User Manual
Electrolux 922216 User Manual
Electrolux 922014 User Manual
Eizo TX D7 User Manual
Cypress CY62136VN User Manual
CyberResearch CPEX P4 24 X User Manual
Asus Computer Hardware AB P 2600 User Manual