DTC-20,21
DTY-21,25,28,29
DTZ-24,28,29
HELPLINE NUMBER : 0870 100 2525
With queries, please quote the page number, reference number and model number
GB
SET-UP MANUAL
Colour Television
CONTENTS
REMOTE CONTROL & TV CONNECTIONS . . . . . . . . . . . . . . . . . . . . . . 3
IMPORTANT SAFEGUARDS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
START UP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
CONNECTING EXTERNAL EQUIPMENT . . . . . . . . . . . . . . . . . . . . . . . 5
DAILY USE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
MENUS DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
TELETEXT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
2
REMOTE CONTROL & TV CONNECTIONS
LOCAL CONTROL
DTC-20,21 / DTY-21,25,28,29
DTZ-24,28 / DTZ-29U7
DTZ-29U3
Front
B1 MAIN POWER button
B6 REMOTE sensor
B2 FRONT VIDEO INPUT socket
B3 FRONT AUDIO INPUT (L + R) socket
B4 HEADPHONE socket
B7 TV / AV button
B8 VOLUME UP/DOWN buttons
B9 PROGRAM UP/DOWN buttons
B10 FRONT PANEL S-VIDEO jack
B5 STAND-BY indicator
Rear
C1 SCART 1 socket
C2 SCART 2 socket
C3 AERIAL jack
REMOTE CONTROL UNIT
TV mode
TELETEXT mode
A1
A2
A3
A4
A5
A6
POWER
SOUND MUTE
NUMBER 0..9
SLEEP
TV / AV
PROGRAM UP
(CURSOR UP)
VOLUME DOWN
A1
A2
A3
A4
A5
A6
A7
A8
A9
POWER
SOUND MUTE
NUMBER 0..9
.
.
PAGE UP
VOL/BRIGHT
CANCEL
PAGE HOLD
A7
(CURSOR LEFT)
A8
A9
A10
.
.
.
A10 SUBPAGE
A11 RED
A12 GREEN
A11 SKIP
A12 MOVE
A13 3D(SOUND EFFECT)
A14 MODE
A15 ZOOM
A13
A14
A15
A16
A17
.
.
.
.
.
A16 RECALL
A18 INDEX
A17 NORMAL
A18 OK/PRESET
A19 MENU
A20 VOLUME UP
(CURSOR RIGHT)
A21 PROGRAM DOWN
(CURSOR DOWN)
A22 TV TELETEXT
A19 VOL/BRIGHT
MENU SELECTION
A20 VOL/BRIGHT
A21 PAGE DOWN
A22 TELETEXT TV
A23 HEIGHT
A24 REVEAL
A25 CYAN
A23
A24
A25
.
.
.
A26 YELLOW
A26 DELETE / FREEZE
3
IMPORTANT SAFEGUARDS
WATER AND MOISTURE
The apparatus shall not be exposed to dripping or splashing water and no object filled with liquids, such as vases , should be
placed on the apparatus.
HEAT
Never place the set near heat sources.
Never put a naked flame, such as a candle, on the top of TV set.
VENTILATION
Do not cover the ventilation openings in the cabinet and never place the set in a confined space such as in a bookcase
or built-in cabinet unless proper ventilation is provided. Leave a minimum 10 cm gap all around the unit.
OBJECT ENTRY
Do not insert foreign objects, such as needles and coins, in the ventilation openings.
LIGHTNING STRIKE
You should disconnect the set from the mains and the aerial system during thunderstorms.
CLEANING
Unplug the set from the mains while cleaning.
AFTER MOVING THE SET
If the set is moved or turned, the MAIN POWER button must be switched off for at least 15 minutes
in order to take out colour patches on the screen.
INSTALLATION
Batteries
Open remote control battery
Insert the main plug into a
230V 50Hz AC power socket.
Connect aerial to aerial jack (C3).
compartment (at the rear) and insert
two 1.5V type AAA batteries. Warning:
be careful to respect battery polarities.
SWITCHING ON AND OFF
Power on the TV set using front panel MAIN POWER button (B1).
Select your preferred language from the LANGUAGE menu (see section START UP on
page 5).
Press the remote control MENU button (A19) to enter the main menu.
Select Install menu to tune and memorise TV programs.
4
START UP
LANGUAGE MENU
The very first time that you turn on the TV, the LANGUAGE menu will appear on the screen. Its purpose is to enable you to select the language that will be
used for all the OSD (On Screen Display) menus. The user must enter a choice of language before proceeding further.
The language entered at this stage can still be modified at any later time, by entering the LANGUAGE menu (accessed from the FEATURES menu: see later
section under MENU DESCRIPTION).
The descriptions used in the menu are those of the country code (e.g. GB = English, NL = Holland etc).
LANGUAGE
BG
F
CZ
FIN
N
D
GB
NL
S
DK
GR
P
E
H
I
PL
RO
RUS
Selection is made by use of the remote control CURSOR UP (A6) / CURSOR DOWN (A21) keys and CURSOR RIGHT (A20) / LEFT (A7) keys.
Once you are satisfied with your selection, push the OK button (A18) to confirm your choice. The choice will briefly highlight in red, after which the menu
will disappear.
Note : The languages shown are subject to modification without prior notice.
AUTOMATIC TUNING
Automatic Tuning System
If you have a satellite decoder: If your decoder is connected to the TV set by the aerial jack (C3), you must power on the demodulator and tune
Sky News before starting ATSS .
ATSS = Automatic Tuning and Sorting System. To start the ATSS function:
- Select„ATSS„ function.
- Adjust to the required country.
- Press and hold the OK button (A18) to start the automatic tuning.
The ATSS function has started when the phrase„Please Wait !”appears (in red characters ) in the help instructions box, below the Install menu.
When the ATSS function is finished, the stored programs are displayed on screen using Edit menu presentation (to Exit tuning before automatic
tuning is finished, press the remote control MENU button (A19) ).
CONNECTING EXTERNAL EQUIPMENT
The rear Scart1 (C1), Scart2 (C2) sockets, the front AV socket (B2) (B3), and the S-VHS socket (B10, option: real flat TVs) are three dedicated
sockets to connect audio-video equipment.
Rear
REAR SCART 1 SOCKET (AV1)
This socket (C1) has video / audio inputs and outputs. It is recommended to
connect to this socket automatic AV switching equipment such as pay-TV
decoders, video games, DVD players and most VCR’s.
In most cases, when connecting powered equipment to this socket, the TV
set switches automatically to AV mode. If not, then use the TV/AV buttons
(A5) or (B7) to select AV1.
REAR SCART 2 SOCKET (AV2)
This socket (C2) has video / audio inputs and outputs. Automatic AV
switching equipment(for example most VCR’s) can be connected to this
socket.
In most cases, when connecting powered equipment to this socket, the TV
set switches automatically to AV mode. If not, then use the TV/AV buttons
(A5) or (B7) to select AV2.
You can also receive an S-VHS signal with REAR SCART2 socket, by
selecting SVHS2 with the TV / AV buttons (A5) or (B7).
VCR / DVD / Video Game / Pay-TV decoder Important:
If your video equipment does not have SCART socket(s), or
if you wish to use only the aerial (RF) connection (not
recommended), then you should make use of PR 00 on the
TV set for best performance.
5
TV/AV SELECTION
Front
Allows to switch between TV and external modes.
By repeatedly pressing the remote control TV / AV (A5) or the TV front panel TV /
AV (B7) button, the on-screen display is changed as shown (SVHS3 is an option):
AV1 > AV2 > SVHS2 > AV3 > SVHS3 > TV
Remark: If the signal source from the rear SCART1 socket (AV1) is RGB (e.g.
normally from a DVD player) then AV1 RGB will be displayed.
HEADPHONE SOCKET
To hear TV sound with
headphones, insert a 3.5mm
headphone plug into the
headphone socket (B4). The
speaker’s sound will be
automatically cut off.
FRONT AV SOCKET (AV3)
VIDEO GAME
The front AV socket (B2) - (B3)
has audio and video inputs. To
switch from TV to these inputs,
use the TV / AV buttons (A5) or
(B7) and select AV3.
FRONT S-VIDEO JACK (Option for DTZ-24,28,29)
The front S-VIDEO jack (B10) has video inputs only.
It is necessary to connect the audio inputs to socket (B3)
in order to have audio and video. To switch from TV to
these inputs, use the TV / AV buttons (A5) or (B7) and
select SVHS3.
OR
CAMCORDER
DAILY USE
SWITCHING ON TV SET
1) If stand-by indicator (B5) is red, then the TV set is in
stand-by mode.
2) If stand-by indicator (B5) is not lit, then the TV
set is powered off.
3) If stand-by indicator (B5) is flashing red, and
green then the TV set is in child-lock mode. It
is necessary to use the remote control POWER
button (A1), NUMBER 0….9 buttons (A3), or
PROGRAM UP (A6) / DOWN (A21) buttons.
The front panel PROGRAM UP/DOWN buttons
(B9) will not function.
You can switch on using the remote control POWER
button (A1), the NUMBER 0….9 buttons (A3), or
PROGRAM UP (A6) / DOWN (A21) buttons.
The front panel PROGRAM UP/DOWN buttons (B9)
can also be used.
You must press the TV set front panel MAIN
POWER button (B1).
If a picture does not appear, then the stand-by
indicator will be lighted red.
In this case, use the remote control as
indicated in 1).
Once on, the stand-by indicator turns to green and
the picture appears on the screen.
Once on, the stand-by indicator turns to green
and the picture appears on the screen.
1) Pressing the remote control POWER button
(A1), you can switch off to stand-by mode
(low power consumption mode) which also
allows quick restart by remote control
(see above: SWITCHING ON TV SET).
2) Pressing the TV set front panel MAIN POWER
button (B1), you can completely power off the
TV set.
In this case, you must use the same front
panel POWER button (B1) to switch on again
(see above: SWITCHING ON TV SET).
SWITCHING OFF TV SET
Remark: If a broadcast signal is not present after 30 minutes, the TV set will be automatically turned to stand-by mode.
6
PROGRAM SELECTION (FROM 0 TO 99)
Direct selection
Up / Down selection
Use the remote control NUMBER 0….9 buttons (A3).
For two digits program numbers, enter the second digit within 2 seconds.
Use the remote control PROGRAM UP (A6) / DOWN (A21) buttons or the
TV set front panel PROGRAM UP / DOWN buttons (B9).
SOUND CONTROL
Mono forcing, dual language
- If you are unable to get good sound
quality for a program due to poor
reception, you can force a change
from stereo to mono transmission
by pressing the remote control
MODE button (A14). Then the
program status display will indicate
„MONO”with a icon.
Volume adjustment
Use the remote control VOLUME UP (A20) / DOWN (A7) buttons or
the TV set front panel VOLUME UP / DOWN buttons (B8).
- On the other hand, during a
program with dual language
transmission, the MODE button
(A14) allows you to toggle between
the first and second language. The
program status display will indicate
„DUAL 1”or„DUAL 2”(plus NICAM
according to the received signal).
- To return to initial state, press again
the MODE button (A14).
Mute
Mute the sound by pressing the remote control
SOUND MUTE button (A2).
Then, logo is displayed. The previous sound
setting is returned after pressing the same button
a second time.
If a sound related function is used (e.g. VOLUME, 3D)
then the MUTE will also be cancelled.
Sound effects
A SPATIAL sound effect is available, using the remote
control 3D (A13) button.
The following display appears:
Spatial sound effect
SPATIAL
Sound transmission mode
STEREO
Clock
18:30
To return to initial sound effect, press again the 3D (A13) button.
The following display appears:
No sound effect
OFF
Sound transmission mode
STEREO
Clock
18:30
As an option, the sound effects PANORAMA and Dolby Virtual are
available with the same button. For other adjustments such as
BALANCE, EQUALIZER or AVL(option), use the SOUND menu
(page10).
Manufactured under license from Dolby Laboratories,„Dolby”
and the double-D symbol are trademarks of Dolby Laboratories.
7
PICTURE CONTROL
You can select three pictures settings, by using the remote control NORMAL button (A17) :
- Normal I (standard hard picture)
- Normal II (standard soft picture)
- Favourite
For other adjustments: BRIGHTNESS, CONTRAST, COLOUR, SHARPNESS, NOISE REDUCTION, use the PICTURE menu.
If an NTSC signal is received, then the TINT adjustment will also be available.
01
BBC1
01
BBC1
01
BBC1
NORMAL I
NORMAL II
FAVOURITE
18:30
18:30
18:30
SLEEP FUNCTION
The set will turn off (to stand-by mode) after a period of time that you can select. By repeated use of the remote control SLEEP
button (A4), you can enter one of the following settings :
OFF 20 min 40 min 60 min 80 min 100 min 120 min OFF
01
BBC1
STEREO
Remaining time (minutes)
before TV set switches off
20
The SLEEP time remaining (before TV turn-off) can be seen again at any time by one
touch on the remote control SLEEP button (A4).
A second touch (while the status display is active) will modify the SLEEP time remaining.
Television Format 4:3
The following picture formats are
available:
FORMAT SELECTION
AUTO setting :
AUTO 14:9 16:9 FULL SCREEN AUTO
If picture format signalling data is
received, then the most appropriate
ZOOM format will be automatically
selected. In the absence of this data, the
default ZOOM format will be selected(see
page 13, ZOOM AUTO function under
FEATURES MENU).
Television Format 16:9
The following picture formats are
available:
AUTO 4:3 ZOOM 14:9 ZOOM 16:9
FULL SCREEN PANORAMA AUTO
Otherwise, the preferred mode of the user
can be forced by repeated pressing of the
remote control ZOOM button (A15):
8
MENUS LANGUAGE SELECTION, CHILD LOCK, CLOCK
SETTING, WAKE UP, NOISE REDUCTION
These functions are available in the Features menu (see description page 13).
CHILD LOCK
Alternatively, the user can enter the time manually using the CLOCK
function. However, if this is done the clock will not be periodically
updated as would happen if the time is set automatically. We
recommend that the user choose (if available) a CLOCK PROG
which allows the time to be updated automatically.
This function only allows the TV to be turned on using the remote
control. Once the user has set this CHILD LOCK to ON or OFF, it will
remain in this condition until the user changes it again.
WAKE UP
DEFAULT ZOOM CONTROL
It is necessary to have set the clock (either manually or
automatically) in order to be able to use this function. If the clock is
not set (--:-- is shown) then the WAKE TIME and WAKE PROG. will
not be selectable.
The default setting for WAKE TIME is in the„OFF”position. After
each use (the TV turns on according to the previous setting) the
WAKE TIME will be returned to the„OFF”position, conserving
always the last time setting entered ready for re-use.
If the ZOOM control is set to AUTO (A15, see page 8, FORMAT
SELECTION), then the picture format presented is controlled by the
received picture format signalling data embedded in the
transmission. In the absence of this signalling data (as can often be
the case) a default format must be used. This default format can be
selected by the ZOOM AUTO function.
LANGUAGE
This can be changed at any time by the user in the LANGUAGE
menu (accessed via the FEATURES menu).
CLOCK SETTING
The TV will automatically attempt to set the clock when powered on
(with the MAIN POWER button). It takes as reference information
embedded in the teletext signal of the channel defined by CLOCK
PROG. Therefore, automatic clock setting is only possible if teletext
is available on this channel.
If no time is captured automatically (the clock will show - - : - -), then
the TV will try again to set the clock whenever turning on from
standby mode.
MENUS DESCRIPTION
MAIN MENU
All menus are removed within 60 seconds if you don’t press any button.
PICTURE
SOUND
INSTALL
Press the remote control MENU button (A19) to display the main menu.
Then, you have the choice between several sub-menus:
If you want to Exit the main menu, press the MENU button (A19) a
second time.
FEATURES
- To select one of the sub-menus, use the remote control CURSOR UP
(A6), DOWN (A21) buttons.
- To enter the selected sub-menu, press the remote control OK button (A18).
Remark: In AV mode the INSTALL menu is not available, and will not be selectable.
HOW TO USE THE SUB-MENUS
The sub-menus referred to here are: PICTURE, SOUND, INSTALL, FEATURES.
- Adjustthe function using :
- Select the desired Position
by using the remote
control CURSOR UP (A6) or
DOWN (A21) buttons.
- The remote control
CURSOR LEFT (A7) or
RIGHT (A20) buttons if
you want to modify the
function value
- The remote control
NUMBER 0...9 buttons (A3)
to enter directly new data.
- Store (if needed) by
pressing the remote
control OK button (A18).
- Then Exit to main menu by
pressing the MENU button
(A19).
9
(For operating instructions, see page 9, HOW TO USE THE SUB-MENUS)
PICTURE MENU
- Select and adjust the level of each function : BRIGHTNESS, CONTRAST,
COLOUR, SHARPNESS, TINT (if available).
PICTURE
FAVOURITE
- The above modified values are automatically stored in FAVOURITE mode.
- NOISE REDUCTION feature can be activated or not.
BRIGHTNESS
CONTRAST
COLOUR
SHARPNESS
TINT
- The OK (A18) or NORMAL button will select the picture presets FAVOURITE,
NORMAL I, NORMAL II. The currently selected preset is displayed in the menu header.
- The FAVOURITE preset contains the settings that you last entered.
If the NTSC standard is detected (eg from VHS player connected to AV1), then
TINT will available. Otherwise TINT will be displayed, but not selectable.
NOISE RED.
ON
SOUND MENU
(For operating instructions, see page 9,HOW TO USE THE SUB-MENUS)
SOUND
VOLUME
BALANCE
EQUALIZER
AVL
NORMAL
OFF
- Select VOLUME function to adjust the volume level.
- Select BALANCE function to adjust sound balance between the left and right speakers. If the indicator is highlighted in red, then the central balance
position has been found.
- Use the EQUALIZER function to select the sound presets MUSIC, SPEECH, NORMAL, FAVOURITE by use of the CURSOR LEFT (A7), RIGHT
(A20) buttons. The FAVOURITE preset contains the settings that you last entered into the EQUALIZER menu.
- The OK button (A18) will enter the EQUALIZER menu, and allow you to change the FAVOURITE settings.
- Automatic Volume Level (AVL, Option) feature has 4 levels according to your preference. This feature corrects for large volume level changes, such
as occur when passing from a movie to advertisements. The AVL solves this problem by equalizing the volume level, over a SHORT MEDIUM or
LONG period (referring to the time constant over which the equalizing effect lasts).
EQUALIZER MENU
- Select the equalizer band by use of the CURSOR LEFT (A7) or RIGHT (A20) buttons.
- Adjust the level of each of the 5 equalizer bands, 100Hz, 300Hz, 1000Hz, 3000Hz,
8000Hz, by use of the CURSOR UP (A6) and DOWN (A21) buttons.
EQUALIZER
NORMAL
- The above modified values are automatically stored in FAVOURITE mode.
- The OK button (A18) will select the picture presets MUSIC, SPEECH, NORMAL,
FAVOURITE. The currently selected preset is displayed in the menu header.
- The FAVOURITE preset always contains the settings that you last entered.
100
300
1k
3k
8k
10
INSTALL MENU
(For operating instructions, see page 9,HOW TO USE THE SUB-MENUS)
Country
Automatic tuning system
INSTALL
Program list edition
TV system modification
Channel number
ATSS
EDIT
GB
TV system
SYSTEM
CHANNEL
FREQUENCY
NAME
PROGRAM
STORE TO
GB
C46
671,25
ABCDEFG
09
Channel number
Channel Frequency
Channel name
Channel Frequency
Channel name
09
Program number
Program number
Program storage number
Program storage number
Automatic Tuning System
If you have a satellite decoder: If your decoder is connected to the TV set by the aerial jack (C3), you must power on the demodulator and
tune Sky News before starting ATSS.
ATSS = Automatic Tuning and Sorting System. To start the ATSS function:
- Select„ATSS”function.
- Adjust to the required country.
- Press and hold the OK button (A18) to start the automatic tuning.
The ATSS function has started when the phrase„Please Wait!”appears (in red characters) in the help instructions box, below the Install
menu.
When the ATSS function is finished, the stored programs are displayed on screen using Edit menu presentation (to Exit tuning before
automatic tuning finished, press the remote control MENU button (A19))
Program List Edition
This allows you to easily manipulate the existing program order allocation, by using Edit menu functions described below.
EDIT
Program number
Station name
PR
03
02
00
99
98
97
NAME
BBC1
BBC2
- - - -
- - - -
- - - -
- - - -
CH
SKIP
C23
C33
S41
S41
S41
S41
Channel number
Skip code
: Program skipped
Nothing : Program not skipped
To enter the EDIT menu: From Install menu, select„Edit”, and press the OK button
(A18): the EDIT menu appears.
The current program being displayed is highlighted in blue (on the central line). In the
above case, the current program is PR00. The 3 previous, and 3 following programs,
are always displayed. Any program from 00 to 99 can be selected, by using the
remote control CURSOR UP (A6) / DOWN (A21) buttons.
The memorised programs can be modified as follows :
11
Channel skipping
Channel deleting
Channel order changing
- You can select skip„YES”or
„NO”using the remote control
RED„Skip”button (A11).
A program with skip„YES”
doesn’t appear on screen
when changing channels with
the PROGRAM UP (A6) /
DOWN (A21) buttons.
- Select the program to delete using
the remote control CURSOR UP
(A6) / DOWN (A21) buttons.
- Press the remote control YELLOW
„Delete”button (A26). The deleted
program is moved to program
number 99 with skip changed to
„YES”. The existing 99 program is
moved to program number 98 and
so on.
- Select the program to move using the
remote control CURSOR UP (A6) / DOWN
(A21) buttons.
- Press the remote control GREEN„Move”
button (A12): the program line background
is highlighted in green, and can be moved
to another position using the remote control
CURSOR UP (A6)/ DOWN (A21) buttons.
- When the desired position is reached,
confirm the new position pressing the
remote control GREEN„Confirm” button
(A12). Then the program line background
will return again to grey.
Channel searching
Manual Channel Tuning
- Select the„Frequency”function.
- Press, and hold for more than 1
second, the remote control
CURSOR RIGHT (A20) [LEFT
(A7)] buttons to start up [down]
manual tuning.
- Searching will stop automatically at
the next channel found (to stop
tuning, press the remote control
MENU button (A19)).
Choose a starting point
- Select with„Program”the
Enter station name
program from which you want
to start manual tuning. Then the
channel number, the frequency,
the name and the program
number of this program are
displayed in the Install menu.
It is possible to enter your own choice of name
for each program. You can change an existing
name, or enter a name where none exists. If
none exists„- - - - - - -”will be shown in the
Install menu, and program status display ( see
the section PROGRAM STATUS DISPLAY on
page 8).
- Select the„NAME”function.
Note: You can directly locate a
program by entering the data
into the„channel”or the
„frequency”function.
- Select one of the 7 character positions by
using the remote control CURSOR RIGHT
(A20) / LEFT (A7) buttons to move the cursor.
- Then use the CURSOR UP (A6) /DOWN (A21)
buttons to select the desired character for
that position.
- Repeat the last two instructions for other
positions, as desired.
- Once the name has been entered, press the
OK button (A18) to store it. The name will be
memorised to the program number currently
shown on the„Store To”line. The„Store To”
program number will highlight in red briefly.
Store program in memory
Perform fine tuning
TV system modification
If necessary, you can modify the
TV system :
- Select„system”function.
- Adjust choosing between
FRANCE (L/L’), GB (I), EURO
(B/G), E/ EURO (D/K) systems.
- Select the„store to”function
- If you are unable to get a good
picture or reasonable quality sound
due to poor reception, it is possible
to perform fine tuning.
- Select the„frequency”function.
- Press, for less than 1 second, the
remote control CURSOR
- Enter the program number you want to
store to either by using the remote control
CURSOR RIGHT (A20) / LEFT (A7) buttons, or
directly by using the remote control NUMBER
0...9 buttons (A3).
- Press the OK button (A18) to confirm.
Then, the program displayed on
the screen is changed to the
chosen system.
RIGHT(A20) [LEFT(A7)] buttons to
perform up [down] fine tuning in
steps of 0.05MHz (50 kHz).
Remarks: this function can also be used if you
want to copy a program already
memorised to another program
number.
12
FEATURES MENU
See section near the end of section DAILY USE for a more detailed explanation of these functions.
(For operating instructions see page 9, HOW TO USE THE SUB-MENUS)
1. When switched to ON:
1. Adjust this value ON or OFF.
Prevents the use of the TV set without remote
control
- In stand-by mode, the stand-by indicator flashes
red and green to indicate the CHILD LOCK is set.
- The front panel TV buttons (B7, B8, B9) become
inactive and the TV will only respond to the
remote control.
2. Wake up function
This function is only selectable when the clock
is set. The TV set turns on from stand-by at the
WAKE TIME with the programme entered on the
WAKE PROG. line. Put the TV set on stand-by with
the remote control
2. Switch the WAKE UP function OFF or ’ON’(the
time will be shown e.g. 07:15) with the remote
control CURSOR LEFT (A7) /RIGHT (A20) buttons
- Enter the wake up time with the remote control
0...9 NUMBER (A3) buttons.
3. Shared with WAKE TIME.
FEATURES
3. Adjust TV turn-on program number
4. TV clock setting
This function allows user to enter the time
manually.
CHILD LOCK
WAKE TIME
WAKE PROG.
CLOCK
OFF
OFF
04
4. Adjust TV clock. Clock will start at 0 seconds
upon entry of the 4th figure.
The prog. no. which can be used to automatically
seize the time at turn on can be entered here.
Note : If you turn off the set with the main power
button, the clock setting is lost. An automatic
attempt is made to set the clock again at power
on.
- -:- -
01
CLOCK PROG
ZOOM AUTO
LANGUAGE
4:3
GB
5. Choose your preferred default format with the
remote control CURSOR LEFT (A7) /RIGHT (A20)
buttons.
Note : For 4:3 TVs FULL SCREEN is represented
by 4:3. For 16:9 TVs FULL SCREEN is repre-
sented by 16:9.
5. This function is only selectable when the default
picture format is currently active (see also
FORMAT SELECTION, AUTO setting, page 8). This
selects the default format to be used only when
the format selected with the ZOOM button (A15)
is AUTO, and no picture format signalling data is
received.
6. The currently selected LANGUAGE is displayed.
Press the OK button (A18) to access the menu
and change the selection.
6. LANGUAGE menu entry.
LANGUAGE MENU
- Select the preferred LANGUAGE by use of the CURSOR LEFT
(A7), RIGHT (A20) buttons, and the CURSOR UP (A6) or DOWN
(A21) buttons.
- Press the OK button (A18) to confirm the selection (the choice
will be highlighted in red).
LANGUAGE
BG
F
CZ
FIN
N
D
GB
NL
S
DK
GR
P
E
H
I
PL
Note : The languages shown are subject to modification without
RO
RUS
prior notice.
13
TELETEXT
ENTERING/LEAVING TELETEXT MODE
- Select the desired program with teletext.
- Press the remote control TELETEXT ( ) button (A22) to select teletext
mode. The initial page (or the last page viewed if you have already used
teletext in the present channel) appears.
- Teletext And Teletext (TAT) function (OPTION): if you want to watch two teletext pages on
same screen, press the TELETEXT ( )button (A22) again. When entering into TAT mode, the
active teletext page is on the left hand part of the screen, at the base of the screen a menu
coloured page links is available. The passive page, on the left hand part, is locked to the active
page, usually it display the next page in the list.
Using the remote control RIGHT (A20) / LEFT (A7) buttons, you can change the active page.
For example, you can held the index page (press HOLD button (A9)); on one side of the screen
and change the active page to the other side for navigation.
- Picture And Teletext (PAT) function (OPTION) : If you want to watch the TV program
and use teletext at the same time, press the TELETEXT button (A22)
again. Teletext will be displayed on the right hand part of the screen, and
the whole TV picture will be compressed into left hand part of the
screen.
- To return to TV mode, press again the TELETEXT ( ) button (A22).
PAGE SELECTION
- You can directly enter the 3 figure page number by using the remote control NUMBER 0...9 buttons (A3).
- You can sequentially select teletext pages by pressing the remote control PAGE UP (A6) / DOWN (A21) buttons.
- At the base of the screen a menu of coloured page links is available, showing either page numbers or a title with headings (eg Sport, News)
in RED, GREEN, YELLOW or CYAN colour. These pages can be accessed by using the corresponding coloured buttons (A11, A12, A26, A25)
on the remote control.
Once a request is made, the page number is shown in the extreme top left corner of the screen. If the requested page is not
immediately available the rolling header will be active until the page arrives.
14
USEFUL TELETEXT FUNCTIONS
PAGE HOLD button ( ) (A9): Any teletext page or
subpage can be held on the screen by pressing the
PAGE HOLD button.
INDEX ( ) button (A18): Allows you to return directly to the
initial teletext page.
- The page number shown in the extreme top left corner
instead of page number the HOLD icon is shown in green.
- Press the HOLD button again to cancel hold mode
(the page number will return to white).
SUBPAGE ( ) button (A10):
- Press the SUBPAGE button (A10). In the extreme top left corner,
instead of the page number, ‘’S. . . .’’will be displayed. This is ready to
accept the subpage number.
- Enter directly the subpage number you want with the remote control
NUMBER 0..9 buttons (A3): for example to request the 2nd subpage,
type 0002.
- After a few seconds the subpage number is replaced by the page
number in the header. You can press again SUBPAGE button (A10), to
display the subpage number.
- If the requested page is not immedietly available the rolling header
will be active until the page arrives.
Warning: If the subpage is not available (does not exist), then the
header will roll continuously and no new page will be found.
Note : Teletext specification allows for subpage numbers 0000
to 3979 (the first figure is limited to the range 0..3, and
the third figure 0..7).
REVEAL ( ) button (A24): Press this button to reveal,
on certain pages, hidden information such as the
answer to a quiz.
- Press the button again to hide the information.
15
TELETEXT FORMAT PICTURE & SOUND CONTROL
Doubling character height
Repeatedly pressing the HEIGHT ( ) button (A23) doubles the character height in the following
order:
Upper half of the page (UP) > Lower half of the page (DOWN) > Return to normal height.
If the page is in UP or DOWN mode, then normal size is automatically set if :
- A new page request is made (e.g. CYAN, INDEX or PAGE UP/DOWN).
- CANCEL mode (A8) function is used.
- VOLUME menu is activated the with the MENU button (A19).
Note : The menu at the base of the screen is always visible
Volume and brightness control in teletext mode
VOLUME ( and sound MUTE), BRIGHTNESS controls are all possible in teletext. The BRIGHTNESS
control are dedicated to the teletext display.
- Access the VOLUME control by pressing the MENU button (A19) in teletext mode. A barograph will appear in the lower part of the screen
(as in TV mode). If MUTE is active a mute icon is also shown.
- A second press on the MENU button (A19) will access the BRIGHTNESS control.
- The active bargraph will timeout after 3-4 seconds (as in TV mode VOLUME control) or by pressing on the MENU button (A19) a third
time after brightness control
- Each control can be adjusted by using the remote control CURSOR RIGHT (A20) / LEFT (A7) buttons.
- Mute can always be activated by pressing the SOUND MUTE button (A2).
- Any change to the VOLUME level will cancel the SOUND MUTE.
WATCHING TV WHILE PAGE SEARCHING
The CANCEL function can be used to make the teletext page transparent, thus revealing
the TV picture:
- To enter cancel mode, press the CANCEL ( ) button (A8) while in teletext mode. The TV
program will reappear on the screen, while only the teletext page number or the cancel icon remains at the
top and left corner of the screen.
- You can enter a new page number in this mode only by using the remote control
NUMBER 0...9 buttons (A3), or with the INDEX ( ) button (A18).
- If a page has been requested, but has not yet arrived, cancel icon will be
displayed until the page arrives. Once arrived the page number will be displayed.
- The teletext page can be made visible again by pressing the CANCEL ( ) button (A8).
- It should be noted that the TV program cannot be changed while in cancel mode.
- The CANCEL function is not available in PAT and TAT mode.
WATCHING TV WITH TELETEXT SUBTITLES
If the actual teletext page is a news flash or subtitle page, then most of the TV picture becomes visible. In this situation the ZOOM
format chosen in TV mode is reactivated, where possible.
This is particularly useful while watching a program with the teletext subtitles. Only formats which do not allow the full height of the
TV picture to be seen are not possible in teletext mode, as these would not allow all teletext lines to be displayed.
Therefore only the formats ZOOM 14:9 AND ZOOM 16:9 (available with wide screen TV models) cannot be preserved with teletext
subtitles. In this situation the default format FULL SCREEN (equal to 16:9) will be used.
16
DMP3901900
|