CY7C1317CV18, CY7C1917CV18
CY7C1319CV18, CY7C1321CV18
18-Mbit DDR-II SRAM 4-Word
Burst Architecture
Features
Functional Description
■ 18-Mbit density (2M x 8, 2M x 9, 1M x 18, 512K x 36)
■ 300 MHz clock for high bandwidth
The CY7C1317CV18, CY7C1917CV18, CY7C1319CV18, and
CY7C1321CV18 are 1.8V Synchronous Pipelined SRAMs
equipped with DDR-II architecture. The DDR-II consists of an
SRAM core with advanced synchronous peripheral circuitry and
a two-bit burst counter. Addresses for read and write are latched
on alternate rising edges of the input (K) clock. Write data is
registered on the rising edges of both K and K. Read data is
driven on the rising edges of C and C if provided, or on the rising
edge of K and K if C/C are not provided. Each address location
is associated with four 8-bit words in the case of CY7C1317CV18
and four 9-bit words in the case of CY7C1917CV18 that burst
sequentially into or out of the device. The burst counter always
starts with a ‘00’ internally in the case of CY7C1317CV18 and
CY7C1917CV18. For CY7C1319CV18 and CY7C1321CV18,
the burst counter takes in the least two significant bits of the
external address and bursts four 18-bit words in the case of
CY7C1319CV18, and four 36-bit words in the case of
CY7C1321CV18, sequentially into or out of the device.
■ 4-word burst for reducing address bus frequency
■ Double Data Rate (DDR) interfaces
(data transferred at 600 MHz) at 300 MHz
■ Two input clocks (K and K) for precise DDR timing
❐ SRAM uses rising edges only
■ Two input clocks for output data (C and C) to minimize clock
skew and flight time mismatches
■ Echo clocks (CQ and CQ) simplify data capture in high-speed
systems
■ Synchronous internally self-timed writes
■ DDR-II operates with 1.5 cycle read latency when the DLL is
enabled
Asynchronous inputs include an output impedance matching
input (ZQ). Synchronous data outputs (Q, sharing the same
physical pins as the data inputs, D) are tightly matched to the two
output echo clocks CQ/CQ, eliminating the need to capture data
separately from each individual DDR SRAM in the system
design. Output data clocks (C/C) enable maximum system
clocking and data synchronization flexibility.
■ Operates similar to a DDR-I device with 1 cycle read latency in
DLL off mode
■ 1.8V core power supply with HSTL inputs and outputs
■ Variable drive HSTL output buffers
■ Expanded HSTL output voltage (1.4V–V
)
DD
All synchronous inputs pass through input registers controlled by
the K or K input clocks. All data outputs pass through output
registers controlled by the C or C (or K or K in a single clock
domain) input clocks. Writes are conducted with on-chip
synchronous self-timed write circuitry.
■ Available in 165-Ball FBGA package (13 x 15 x 1.4 mm)
■ Offered in both Pb-free and non Pb-free packages
■ JTAG 1149.1 compatible test access port
■ Delay Lock Loop (DLL) for accurate data placement
Configurations
CY7C1317CV18 – 2M x 8
CY7C1917CV18 – 2M x 9
CY7C1319CV18 – 1M x 18
CY7C1321CV18 – 512K x 36
Selection Guide
Description
300 MHz
300
278 MHz
278
250 MHz
250
200 MHz
200
167 MHz
167
Unit
MHz
mA
Maximum Operating Frequency
Maximum Operating Current
x8
x9
770
720
670
580
515
770
720
670
580
515
x18
x36
810
760
700
600
540
890
830
765
655
600
Cypress Semiconductor Corporation
Document Number: 001-07161 Rev. *D
•
198 Champion Court
•
San Jose, CA 95134-1709
•
408-943-2600
Revised June 18, 2008
CY7C1317CV18, CY7C1917CV18
CY7C1319CV18, CY7C1321CV18
Logic Block Diagram (CY7C1319CV18)
Burst
Logic
A
(1:0)
2
Write Write
Reg
Reg
Write
Reg
Write
Reg
20 18
A
A
(19:0)
Address
Register
(19:2)
18
LD
K
K
Output
R/W
CLK
Logic
Gen.
Control
C
C
DOFF
Read Data Reg.
72
36
CQ
CQ
V
18
18
18
18
REF
Reg.
Reg.
Reg.
Control
Logic
R/W
36
BWS
18
[1:0]
DQ
[17:0]
Logic Block Diagram (CY7C1321CV18)
Burst
Logic
A
(1:0)
2
Write Write
Reg
Reg
Write
Reg
Write
Reg
19 17
A
A
(18:0)
Address
Register
(18:2)
36
LD
K
K
Output
Logic
Control
CLK
R/W
Gen.
C
C
DOFF
Read Data Reg.
144
72
CQ
V
36
36
36
36
REF
Reg.
Reg.
Reg.
Control
Logic
CQ
R/W
72
36
BWS
DQ
[3:0]
[35:0]
Document Number: 001-07161 Rev. *D
Page 3 of 31
CY7C1317CV18, CY7C1917CV18
CY7C1319CV18, CY7C1321CV18
Pin Configuration
The pin configuration for CY7C1317CV18, CY7C1917CV18, CY7C1319CV18, and CY7C1321CV18 follow.
165-Ball FBGA (13 x 15 x 1.4 mm) Pinout
CY7C1317CV18 (2M x 8)
1
CQ
NC
NC
NC
NC
NC
NC
DOFF
NC
NC
NC
NC
NC
NC
TDO
2
NC/72M
NC
3
4
R/W
A
5
6
K
7
8
LD
A
9
10
NC/36M
NC
11
CQ
DQ3
NC
NC
DQ2
NC
NC
ZQ
A
B
C
D
E
F
A
NWS
NC/144M
A
1
NC
NC
NC
DQ4
NC
DQ5
NC/288M
A
K
NWS
A
NC
NC
NC
NC
NC
NC
0
NC
V
V
NC
V
NC
SS
SS
SS
SS
NC
V
V
V
V
V
V
V
V
V
V
V
V
V
V
NC
SS
SS
DD
DD
DD
DD
DD
SS
SS
SS
SS
SS
SS
SS
SS
SS
SS
SS
DD
DD
DD
DD
DD
NC
V
V
V
V
V
V
V
V
V
V
V
V
V
V
NC
DDQ
DDQ
DDQ
DDQ
DDQ
DDQ
DDQ
DDQ
DDQ
DDQ
DDQ
DDQ
DDQ
DDQ
NC
V
V
V
V
V
V
V
V
V
V
NC
G
H
J
NC
NC
V
V
V
V
REF
REF
DDQ
DDQ
NC
NC
NC
NC
DQ1
NC
NC
NC
DQ0
NC
NC
NC
TDI
K
L
NC
NC
NC
NC
DQ7
A
NC
NC
NC
NC
NC
A
DQ6
NC
V
V
V
V
NC
SS
SS
SS
SS
M
N
P
R
V
V
NC
SS
SS
SS
NC
V
A
A
A
A
C
C
A
A
A
V
NC
SS
NC
A
A
A
A
NC
TCK
TMS
CY7C1917CV18 (2M x 9)
1
CQ
NC
NC
NC
NC
NC
NC
DOFF
NC
NC
NC
NC
NC
NC
TDO
2
NC/72M
NC
3
4
5
NC
6
K
7
8
9
10
NC/36M
NC
11
CQ
DQ3
NC
A
B
C
D
E
F
A
R/W
A
NC/144M
LD
A
A
NC
NC
NC
DQ4
NC
DQ5
NC/288M
A
K
BWS
A
NC
NC
NC
NC
NC
NC
0
NC
V
V
NC
V
NC
SS
SS
SS
SS
NC
V
V
V
V
V
V
V
V
V
V
V
V
V
V
NC
NC
SS
SS
DD
DD
DD
DD
DD
SS
SS
SS
SS
SS
SS
SS
SS
SS
SS
SS
DD
DD
DD
DD
DD
NC
V
V
V
V
V
V
V
V
V
V
V
V
V
V
NC
DQ2
NC
DDQ
DDQ
DDQ
DDQ
DDQ
DDQ
DDQ
DDQ
DDQ
DDQ
DDQ
DDQ
DDQ
DDQ
NC
V
V
V
V
V
V
V
V
V
V
NC
G
H
J
NC
NC
NC
V
V
V
V
REF
ZQ
REF
DDQ
DDQ
NC
NC
NC
NC
DQ1
NC
NC
K
L
NC
NC
NC
NC
DQ7
A
NC
NC
NC
NC
NC
A
NC
DQ6
NC
V
V
NC
DQ0
NC
SS
SS
SS
SS
M
N
P
R
V
V
V
V
NC
SS
SS
SS
NC
V
A
A
A
A
C
C
A
A
A
V
NC
NC
SS
NC
A
A
A
A
NC
DQ8
TDI
TCK
TMS
Note
1. NC/36M, NC/72M, NC/144M, and NC/288M are not connected to the die and can be tied to any voltage level.
Document Number: 001-07161 Rev. *D
Page 4 of 31
CY7C1317CV18, CY7C1917CV18
CY7C1319CV18, CY7C1321CV18
Pin Configuration (continued)
[1]
The pin configuration for CY7C1317CV18, CY7C1917CV18, CY7C1319CV18, and CY7C1321CV18 follow.
165-Ball FBGA (13 x 15 x 1.4 mm) Pinout
CY7C1319CV18 (1M x 18)
1
CQ
NC
NC
NC
NC
NC
NC
DOFF
NC
NC
NC
NC
NC
NC
TDO
2
NC/72M
DQ9
NC
3
4
R/W
A
5
6
K
7
8
LD
A
9
10
NC/36M
NC
11
CQ
A
B
C
D
E
F
A
BWS
NC/144M
A
1
NC
NC/288M
A
K
BWS
A1
NC
NC
NC
NC
NC
NC
DQ8
NC
0
NC
V
V
A0
V
DQ7
NC
SS
SS
SS
SS
NC
DQ10
DQ11
NC
V
V
V
V
V
V
NC
SS
SS
DD
DD
DD
DD
DD
SS
SS
SS
SS
SS
SS
SS
SS
SS
SS
SS
DD
DD
DD
DD
DD
NC
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
NC
DQ6
DQ5
NC
DDQ
DDQ
DDQ
DDQ
DDQ
DDQ
DDQ
DDQ
DDQ
DDQ
DDQ
DDQ
DDQ
DDQ
DQ12
NC
V
V
V
V
V
V
V
V
V
V
NC
G
H
J
DQ13
NC
V
V
V
V
REF
ZQ
REF
DDQ
DDQ
NC
NC
NC
DQ14
NC
NC
DQ4
NC
NC
K
L
NC
NC
NC
NC
NC
A
DQ3
DQ2
NC
DQ15
NC
V
V
V
V
NC
SS
SS
SS
SS
M
N
P
R
NC
V
V
DQ1
NC
SS
SS
SS
NC
DQ16
DQ17
A
V
A
A
A
A
C
C
A
A
A
V
NC
SS
NC
A
A
A
A
NC
DQ0
TDI
TCK
TMS
CY7C1321CV18 (512K x 36)
1
CQ
NC
NC
NC
NC
NC
NC
DOFF
NC
NC
NC
NC
NC
NC
TDO
2
3
4
5
BWS
BWS
A
6
K
7
8
9
10
NC/72M
NC
11
A
B
C
D
E
F
NC/144M NC/36M
R/W
A
BWS
BWS
A1
LD
A
A
CQ
2
3
1
DQ27
NC
DQ18
DQ28
DQ19
DQ20
DQ21
DQ22
K
NC
NC
NC
NC
NC
NC
DQ8
DQ7
DQ16
DQ6
DQ5
DQ14
ZQ
0
V
V
A0
V
DQ17
NC
SS
SS
SS
SS
DQ29
NC
V
V
V
V
V
V
SS
SS
DD
DD
DD
DD
DD
SS
SS
SS
SS
SS
SS
SS
SS
SS
SS
SS
DD
DD
DD
DD
DD
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
DQ15
NC
DDQ
DDQ
DDQ
DDQ
DDQ
DDQ
DDQ
DDQ
DDQ
DDQ
DDQ
DDQ
DDQ
DDQ
DQ30
DQ31
V
V
V
V
V
V
V
V
V
V
G
H
J
NC
V
V
V
V
REF
REF
DDQ
DDQ
NC
NC
DQ32
DQ23
DQ24
DQ34
DQ25
DQ26
A
NC
DQ13
DQ12
NC
DQ4
DQ3
DQ2
DQ1
DQ10
DQ0
TDI
K
L
NC
NC
NC
NC
NC
A
DQ33
NC
V
V
SS
SS
SS
SS
M
N
P
R
V
V
V
V
DQ11
NC
SS
SS
SS
DQ35
NC
V
A
A
A
A
C
C
A
A
A
V
SS
A
A
A
A
DQ9
TMS
TCK
Document Number: 001-07161 Rev. *D
Page 5 of 31
CY7C1317CV18, CY7C1917CV18
CY7C1319CV18, CY7C1321CV18
Pin Definitions
Pin Name
DQ
IO
Pin Description
Input Output- Data Input Output Signals. Inputs are sampled on the rising edge of K and K clocks during valid write
Synchronous operations. These pins drive out the requested data during a read operation. Valid data is driven out on
the rising edge of both the C and C clocks during read operations or K and K when in single clock mode.
[x:0]
When read access is deselected, Q
are automatically tri-stated.
[x:0]
CY7C1317CV18 − DQ
[7:0]
CY7C1917CV18 − DQ
[8:0]
CY7C1319CV18 − DQ
CY7C1321CV18 − DQ
[17:0]
[35:0]
LD
Input-
Synchronous Load. This input is brought LOW when a bus cycle sequence is defined. This definition
Synchronous includes address and read/write direction. All transactions operate on a burst of 4 data (two clock periods
of bus activity).
NWS ,
Input-
Nibble Write Select 0, 1 − Active LOW (CY7C1317CV18 only). Sampled on the rising edge of the K
0
NWS
Synchronous and K clocks during write operations. Used to select which nibble is written into the device during the
1
current portion of the write operations. Nibbles not written remain unaltered.
NWS controls D
and NWS controls D
.
0
[3:0]
1
[7:4]
All the Nibble Write Selects are sampled on the same edge as the data. Deselecting a Nibble Write Select
ignores the corresponding nibble of data and it is not written into the device.
BWS ,
Input-
Byte Write Select 0, 1, 2, and 3 − Active LOW. Sampled on the rising edge of the K and K clocks during
0
BWS ,
Synchronous write operations. Used to select which byte is written into the device during the current portion of the Write
1
BWS ,
operations. Bytes not written remain unaltered.
2
BWS
CY7C1917CV18 − BWS controls D
3
0
[8:0]
CY7C1319CV18 − BWS controls D
and BWS controls D
[17:9].
0
[8:0]
1
CY7C1321CV18 − BWS controls D
, BWS controls D
, BWS controls D
and BWS controls
0
[8:0]
1
[17:9]
2
[26:18]
3
D
.
[35:27]
All the Byte Write Selects are sampled on the same edge as the data. Deselecting a Byte Write Select
ignores the corresponding byte of data and it is not written into the device.
A, A0, A1
Input-
Address Inputs. These address inputs are multiplexed for both read and write operations. Internally, the
Synchronous device is organized as 2M x 8 (4 arrays each of 512K x 8) for CY7C1317CV18 and 2M x 9 (4 arrays each
of 512K x 9) for CY7C1917CV18, 1M x 18 (4 arrays each of 256K x 18) for CY7C1319CV18, and 512K
x 36 (4 arrays each of 128K x 36) for CY7C1321CV18.
CY7C1317CV18 – Because the least two significant bits of the address internally are “00”, only 19 external
address inputs are needed to access the entire memory array.
CY7C1917CV18 – Because the least two significant bits of the address internally are “00”, only 19 external
address inputs are needed to access the entire memory array.
CY7C1319CV18 – A0 and A1 are the inputs to the burst counter. These are incremented internally in a
linear fashion. 20 address inputs are needed to access the entire memory array.
CY7C1321CV18 – A0 and A1 are the inputs to the burst counter. These are incremented internally in a
linear fashion. 19 address inputs are needed to access the entire memory array.
R/W
C
Input-
Synchronous Read/Write Input. When LD is LOW, this input designates the access type (read when
Synchronous R/W is HIGH, write when R/W is LOW) for the loaded address. R/W must meet the setup and hold times
around the edge of K.
Input Clock Positive Input Clock for Output Data. C is used in conjunction with C to clock out the read data from
the device. C and C can be used together to deskew the flight times of various devices on the board back
C
Input Clock Negative Input Clock for Output Data. C is used in conjunction with C to clock out the read data from
the device. C and C can be used together to deskew the flight times of various devices on the board back
K
Input Clock Positive Input Clock Input. The rising edge of K is used to capture synchronous inputs to the device
and to drive out data through Q
edge of K.
when in single clock mode. All accesses are initiated on the rising
[x:0]
K
Input Clock Negative Input Clock Input. K is used to capture synchronous data being presented to the device and
to drive out data through Q when in single clock mode.
[x:0]
Document Number: 001-07161 Rev. *D
Page 6 of 31
CY7C1317CV18, CY7C1917CV18
CY7C1319CV18, CY7C1321CV18
Pin Definitions (continued)
Pin Name
IO
Pin Description
CQ
Output Clock CQ Referenced with Respect to C. This is a free running clock and is synchronized to the input clock
for output data (C) of the DDR-II. In single clock mode, CQ is generated with respect to K. The timing for
CQ
ZQ
Output Clock CQ Referenced with Respect to C. This is a free running clock and is synchronized to the input clock
for output data (C) of the DDR-II. In single clock mode, CQ is generated with respect to K. The timing for
Input
Output Impedance Matching Input. This input is used to tune the device outputs to the system data bus
impedance. CQ, CQ, and Q output impedance are set to 0.2 x RQ, where RQ is a resistor connected
[x:0]
between ZQ and ground. Alternatively, this pin can be connected directly to V
, which enables the
DDQ
minimum impedance mode. This pin cannot be connected directly to GND or left unconnected.
DOFF
Input
DLL Turn Off − Active LOW. Connecting this pin to ground turns off the DLL inside the device. The timing
in the DLL turned off operation is different from that listed in this data sheet. For normal operation, this
pin can be connected to a pull up through a 10 Kohm or less pull up resistor. The device behaves in DDR-I
mode when the DLL is turned off. In this mode, the device can be operated at a frequency of up to 167
MHz with DDR-I timing.
TDO
Output
Input
Input
Input
N/A
TDO for JTAG.
TCK
TCK Pin for JTAG.
TDI
TDI Pin for JTAG.
TMS
TMS Pin for JTAG.
NC
Not Connected to the Die. Can be tied to any voltage level.
Not Connected to the Die. Can be tied to any voltage level.
Not Connected to the Die. Can be tied to any voltage level.
Not Connected to the Die. Can be tied to any voltage level.
Not Connected to the Die. Can be tied to any voltage level.
Reference Voltage Input. Static input used to set the reference level for HSTL inputs, outputs, and AC
NC/36M
NC/72M
NC/144M
NC/288M
N/A
N/A
N/A
N/A
V
Input-
REF
Reference measurement points.
V
V
V
Power Supply Power Supply Inputs to the Core of the Device.
DD
Ground
Ground for the Device.
SS
Power Supply Power Supply Inputs for the Outputs of the Device.
DDQ
Document Number: 001-07161 Rev. *D
Page 7 of 31
CY7C1317CV18, CY7C1917CV18
CY7C1319CV18, CY7C1321CV18
Write Operations
Functional Overview
Write operations are initiated by asserting R/W LOW and LD
LOW at the rising edge of the positive input clock (K). The
address presented to address inputs is stored in the write
address register and the least two significant bits of the address
are presented to the burst counter. The burst counter increments
the address in a linear fashion. On the following K clock rise the
The CY7C1317CV18, CY7C1917CV18, CY7C1319CV18, and
CY7C1321CV18 are synchronous pipelined Burst SRAMs
equipped with a DDR interface, which operates with a read
latency of one and half cycles when DOFF pin is tied HIGH.
When DOFF pin is set LOW or connected to V the device
SS
behaves in DDR-I mode with a read latency of one clock cycle.
data presented to D
is latched and stored into the 18-bit
[17:0]
Accesses are initiated on the rising edge of the positive input
clock (K). All synchronous input timing is referenced from the
rising edge of the input clocks (K and K) and all output timing is
referenced to the rising edge of the output clocks (C/C, or K/K
when in single clock mode).
write data register, provided BWS
are both asserted active.
[1:0]
On the subsequent rising edge of the negative input clock (K) the
information presented to D is also stored into the write data
[17:0]
register, provided BWS
are both asserted active. This
[1:0]
process continues for one more cycle until four 18-bit words (a
total of 72 bits) of data are stored in the SRAM. The 72 bits of
data are then written into the memory array at the specified
location. Therefore, Write accesses to the device can not be
initiated on two consecutive K clock rises. The internal logic of
the device ignores the second write request. Write accesses can
be initiated on every other rising edge of the positive input clock
(K). Doing so pipelines the data flow such that 18 bits of data can
be transferred into the device on every rising edge of the input
clocks (K and K).
All synchronous data inputs (D
) pass through input registers
[x:0]
controlled by the rising edge of the input clocks (K and K). All
synchronous data outputs (Q ) pass through output registers
[x:0]
controlled by the rising edge of the output clocks (C/C, or K/K
when in single-clock mode).
All synchronous control (R/W, LD, BWS
) inputs pass through
[0:X]
input registers controlled by the rising edge of the input clock (K).
CY7C1319CV18 is described in the following sections. The
same basic descriptions apply to CY7C1317CV18,
CY7C1917CV18, and CY7C1321CV18.
When Write access is deselected, the device ignores all inputs
after the pending write operations are completed.
Read Operations
Byte Write Operations
The CY7C1319CV18 is organized internally as four arrays of
256K x 18. Accesses are completed in a burst of four sequential
18-bit data words. Read operations are initiated by asserting
R/W HIGH and LD LOW at the rising edge of the positive input
clock (K). The address presented to address inputs is stored in
the read address register and the least two significant bits of the
address are presented to the burst counter. The burst counter
increments the address in a linear fashion. Following the next K
clock rise, the corresponding 18-bit word of data from this
Byte write operations are supported by the CY7C1319CV18. A
write operation is initiated as described in the Write Operations
section. The bytes that are written are determined by BWS and
0
BWS , which are sampled with each set of 18-bit data words.
1
Asserting the appropriate Byte Write Select input during the data
portion of a write latches the data being presented and writes it
into the device. Deasserting the Byte Write Select input during
the data portion of a write enables the data stored in the device
for that byte to remain unaltered. This feature can be used to
simplify read/modify/write operations to a byte write operation.
address location is driven onto Q
, using C as the output
[17:0]
timing reference. On the subsequent rising edge of C the next
18-bit data word from the address location generated by the
Single Clock Mode
burst counter is driven onto Q
. This process continues until
[17:0]
The CY7C1319CV18 can be used with a single clock that
controls both the input and output registers. In this mode the
device recognizes only a single pair of input clocks (K and K) that
control both the input and output registers. This operation is
identical to the operation if the device had zero skew between
the K/K and C/C clocks. All timing parameters remain the same
in this mode. To use this mode of operation, tie C and C HIGH at
power on. This function is a strap option and not alterable during
device operation.
all four 18-bit data words have been driven out onto Q
. The
[17:0]
requested data is valid 0.45 ns from the rising edge of the output
clock (C or C, or K and K when in single clock mode, for 200 MHz
and 250 MHz device). To maintain the internal logic, each read
access must be allowed to complete. Each Read access
consists of four 18-bit data words and takes two clock cycles to
complete. Therefore, Read accesses to the device can not be
initiated on two consecutive K clock rises. The internal logic of
the device ignores the second read request. Read accesses can
be initiated on every other K clock rise. Doing so pipelines the
data flow such that data is transferred out of the device on every
rising edge of the output clocks (C/C or K/K when in single-clock
mode).
DDR Operation
The CY7C1319CV18 enables high-performance operation
through high clock frequencies (achieved through pipelining) and
double data rate mode of operation. The CY7C1319CV18
requires a single No Operation (NOP) cycle when transitioning
from a read to a write cycle. At higher frequencies, some appli-
cations may require a second NOP cycle to avoid contention.
The CY7C1319CV18 first completes the pending read transac-
tions, when read access is deselected. Synchronous internal
circuitry automatically tri-states the output following the next
rising edge of the positive output clock (C). This enables a
seamless transition between devices without the insertion of wait
states in a depth expanded memory.
If a read occurs after a write cycle, address and data for the write
are stored in registers. The write information must be stored
because the SRAM cannot perform the last word write to the
array without conflicting with the read. The data stays in this
register until the next write cycle occurs. On the first write cycle
Document Number: 001-07161 Rev. *D
Page 8 of 31
CY7C1317CV18, CY7C1917CV18
CY7C1319CV18, CY7C1321CV18
after the read(s), the stored data from the earlier write is written
into the SRAM array. This is called a posted write.
Echo Clocks
Echo clocks are provided on the DDR-II to simplify data capture
on high-speed systems. Two echo clocks are generated by the
DDR-II. CQ is referenced with respect to C and CQ is referenced
with respect to C. These are free running clocks and are synchro-
nized to the output clock of the DDR-II. In the single clock mode,
CQ is generated with respect to K and CQ is generated with
If a read is performed on the same address on which a write is
performed in the previous cycle, the SRAM reads out the most
current data. The SRAM does this by bypassing the memory
array and reading the data from the registers.
Depth Expansion
Depth expansion requires replicating the LD control signal for
each bank. All other control signals can be common between
banks as appropriate.
DLL
These chips use a Delay Lock Loop (DLL) that is designed to
function between 120 MHz and the specified maximum clock
frequency. During power up, when the DOFF is tied HIGH, the
DLL is locked after 1024 cycles of stable clock. The DLL can also
be reset by slowing or stopping the input clocks K and K for a
minimum of 30 ns. However, it is not necessary to reset the DLL
to lock to the desired frequency. The DLL automatically locks
1024 clock cycles after a stable clock is presented. The DLL may
be disabled by applying ground to the DOFF pin. When the DLL
is turned off, the device behaves in DDR-I mode (with one cycle
latency and a longer access time). For information refer to the
application note DLL Considerations in QDRII™/DDRII.
Programmable Impedance
An external resistor, RQ, must be connected between the ZQ pin
on the SRAM and V to enable the SRAM to adjust its output
SS
driver impedance. The value of RQ must be 5x the value of the
intended line impedance driven by the SRAM. The allowable
range of RQ to guarantee impedance matching with a tolerance
of ±15% is between 175Ω and 350Ω, with V
output impedance is adjusted every 1024 cycles at power up to
account for drifts in supply voltage and temperature.
= 1.5V. The
DDQ
Document Number: 001-07161 Rev. *D
Page 9 of 31
CY7C1317CV18, CY7C1917CV18
CY7C1319CV18, CY7C1321CV18
Application Example
Figure 1 shows two DDR-II used in an application.
Figure 1. Application Example
R = 250ohms
R = 250ohms
SRAM#2
SRAM#1
ZQ
ZQ
DQ
A
DQ
A
CQ/CQ#
LD# R/W# C C# K K#
CQ/CQ#
LD# R/W# C C#
K
K#
DQ
Addresses
Cycle Start#
R/W#
Return CLK
Source CLK
Return CLK#
Source CLK#
BUS
MASTER
(CPU
or
Vterm = 0.75V
R = 50ohms
Vterm = 0.75V
ASIC)
Echo Clock1/Echo Clock#1
Echo Clock2/Echo Clock#2
Truth Table
The truth table for the CY7C1317CV18, CY7C1917CV18, CY7C1319CV18, and CY7C1321CV18 follows.
Operation
K
LD R/W
DQ
DQ
DQ
DQ
Write Cycle:
L-H
L
L
D(A1) at K(t + 1)↑ D(A2) at K(t + 1)↑ D(A3) at K(t + 2)↑ D(A4) at K(t + 2)↑
Load address; wait one cycle;
input write data on four consecutive K
and K rising edges.
Read Cycle:
L-H
L
H Q(A1) at C(t + 1)↑ Q(A2) at C(t + 2)↑ Q(A3) at C(t + 2)↑ Q(A4) at C(t + 3)↑
Load address; wait one and a half cycle;
read data on four consecutive C and C
rising edges.
NOP: No Operation
L-H
H
X
X
X
High-Z
High-Z
High-Z
High-Z
Standby: Clock Stopped
Stopped
Previous State
Previous State
Previous State
Previous State
Notes
2. X = “Don’t Care,” H = Logic HIGH, L = Logic LOW, ↑ represents rising edge.
3. Device powers up deselected with the outputs in a tri-state condition.
4. On CY7C1319CV18 and CY7C1321CV18, “A1” represents address location latched by the devices when transaction was initiated and “A2”, “A3”, “A4” represents the
addresses sequence in the burst. On CY7C1317CV18 and CY7C1917CV18, “A1” represents A + ‘00’ and “A2” represents A + ‘01’, “A3” represents A + ‘10’ and “A4”
represents A + ‘11’.
5. “t” represents the cycle at which a read/write operation is started. t + 1 and t + 2 are the first and second clock cycles succeeding the “t” clock cycle.
6. Data inputs are registered at K and K rising edges. Data outputs are delivered on C and C rising edges, except when in single clock mode.
7. It is recommended that K = K and C = C = HIGH when clock is stopped. This is not essential, but permits most rapid restart by overcoming transmission line charging
symmetrically.
Document Number: 001-07161 Rev. *D
Page 10 of 31
CY7C1317CV18, CY7C1917CV18
CY7C1319CV18, CY7C1321CV18
Burst Address Table
(CY7C1319CV18, CY7C1321CV18)
First Address (External)
Second Address (Internal)
Third Address (Internal)
Fourth Address (Internal)
X..X00
X..X01
X..X10
X..X11
X..X01
X..X10
X..X11
X..X00
X..X10
X..X11
X..X00
X..X01
X..X11
X..X00
X..X01
X..X10
Write Cycle Descriptions
The write cycle description table for CY7C1317CV18 and CY7C1319CV18 follows.
BWS / BWS /
0
1
K
Comments
K
NWS
NWS
1
0
L
L
L
L
L–H
–
During the data portion of a write sequence :
CY7C1317CV18 − both nibbles (D
) are written into the device,
[7:0]
CY7C1319CV18 − both bytes (D
) are written into the device.
[17:0]
–
L–H
–
L-H During the data portion of a write sequence :
CY7C1317CV18 − both nibbles (D
) are written into the device,
) are written into the device.
[7:0]
CY7C1319CV18 − both bytes (D
[17:0]
L
H
H
L
–
During the data portion of a write sequence :
CY7C1317CV18 − only the lower nibble (D
) is written into the device, D
) is written into the device, D
remains unaltered.
remains unaltered.
[3:0]
[7:4]
CY7C1319CV18 − only the lower byte (D
[8:0]
[17:9]
L
L–H During the data portion of a write sequence :
CY7C1317CV18 − only the lower nibble (D
) is written into the device, D
) is written into the device, D
remains unaltered.
remains unaltered.
[17:9]
[3:0]
[7:4]
CY7C1319CV18 − only the lower byte (D
[8:0]
H
H
L–H
–
–
During the data portion of a write sequence :
CY7C1317CV18 − only the upper nibble (D
) is written into the device, D
) is written into the device, D
remains unaltered.
[3:0]
[7:4]
CY7C1319CV18 − only the upper byte (D
remains unaltered.
[17:9]
[8:0]
L
L–H During the data portion of a write sequence :
CY7C1317CV18 − only the upper nibble (D
) is written into the device, D
) is written into the device, D
remains unaltered.
remains unaltered.
[7:4]
[3:0]
[8:0]
CY7C1319CV18 − only the upper byte (D
[17:9]
H
H
H
H
L–H
–
–
No data is written into the devices during this portion of a write operation.
L–H No data is written into the devices during this portion of a write operation.
Write Cycle Descriptions
The write cycle description table for CY7C1917CV18 follows.
BWS
K
L–H
–
K
Comments
During the data portion of a write sequence, the single byte (D
0
L
L
–
) is written into the device.
) is written into the device.
[8:0]
L–H During the data portion of a write sequence, the single byte (D
[8:0]
H
H
L–H
–
–
No data is written into the device during this portion of a write operation.
L–H No data is written into the device during this portion of a write operation.
Note
8. Is based on a write cycle that was initiated in accordance with the Write Cycle Descriptions table. NWS , NWS , BWS , BWS , BWS , and BWS can be altered on
0
1
0
1
2
3
different portions of a write cycle, as long as the setup and hold requirements are achieved.
Document Number: 001-07161 Rev. *D
Page 11 of 31
CY7C1317CV18, CY7C1917CV18
CY7C1319CV18, CY7C1321CV18
Write Cycle Descriptions
The write cycle description table for CY7C1321CV18 follows.
BWS
BWS
BWS
BWS
3
K
K
Comments
0
1
2
L
L
L
L
L–H
–
During the data portion of a write sequence, all four bytes (D
the device.
) are written into
) are written into
[35:0]
L
L
L
H
H
L
L
H
H
H
H
L
L
H
H
H
H
H
H
L
–
L–H
–
L–H During the data portion of a write sequence, all four bytes (D
the device.
[35:0]
–
During the data portion of a write sequence, only the lower byte (D
) is written
) is written
[8:0]
[8:0]
into the device. D
remains unaltered.
[35:9]
L
L–H During the data portion of a write sequence, only the lower byte (D
into the device. D remains unaltered.
[35:9]
H
H
H
H
H
H
L–H
–
–
During the data portion of a write sequence, only the byte (D
) is written into
) is written into
[17:9]
the device. D
and D
remains unaltered.
[8:0]
[35:18]
L
L–H During the data portion of a write sequence, only the byte (D
the device. D and D remains unaltered.
[17:9]
[8:0]
[35:18]
H
H
H
H
L–H
–
–
During the data portion of a write sequence, only the byte (D
) is written into
) is written into
) is written into
) is written into
[26:18]
[26:18]
[35:27]
[35:27]
the device. D
and D
remains unaltered.
[17:0]
[35:27]
L
L–H During the data portion of a write sequence, only the byte (D
the device. D and D remains unaltered.
[17:0]
[35:27]
H
H
L–H
–
–
During the data portion of a write sequence, only the byte (D
the device. D remains unaltered.
[26:0]
L
L–H During the data portion of a write sequence, only the byte (D
the device. D remains unaltered.
[26:0]
H
H
H
H
H
H
H
H
L–H
–
–
No data is written into the device during this portion of a write operation.
L–H No data is written into the device during this portion of a write operation.
Document Number: 001-07161 Rev. *D
Page 12 of 31
CY7C1317CV18, CY7C1917CV18
CY7C1319CV18, CY7C1321CV18
Instruction Register
IEEE 1149.1 Serial Boundary Scan (JTAG)
Three-bit instructions can be serially loaded into the instruction
register. This register is loaded when it is placed between the TDI
page 16. Upon power up, the instruction register is loaded with
the IDCODE instruction. It is also loaded with the IDCODE
instruction if the controller is placed in a reset state, as described
in the previous section.
These SRAMs incorporate a serial boundary scan Test Access
Port (TAP) in the FBGA package. This part is fully compliant with
IEEE Standard #1149.1-2001. The TAP operates using JEDEC
standard 1.8V IO logic levels.
Disabling the JTAG Feature
It is possible to operate the SRAM without using the JTAG
feature. To disable the TAP controller, TCK must be tied LOW
When the TAP controller is in the Capture-IR state, the two least
significant bits are loaded with a binary “01” pattern to allow for
fault isolation of the board level serial test path.
(V ) to prevent clocking of the device. TDI and TMS are inter-
SS
nally pulled up and may be unconnected. They may alternatively
be connected to V through a pull up resistor. TDO must be left
unconnected. Upon power up, the device comes up in a reset
state, which does not interfere with the operation of the device.
Bypass Register
DD
To save time when serially shifting data through registers, it is
sometimes advantageous to skip certain chips. The bypass
register is a single-bit register that can be placed between TDI
and TDO pins. This enables shifting of data through the SRAM
with minimal delay. The bypass register is set LOW (V ) when
the BYPASS instruction is executed.
Test Access Port—Test Clock
The test clock is used only with the TAP controller. All inputs are
captured on the rising edge of TCK. All outputs are driven from
the falling edge of TCK.
SS
Boundary Scan Register
Test Mode Select (TMS)
The boundary scan register is connected to all of the input and
output pins on the SRAM. Several No Connect (NC) pins are also
included in the scan register to reserve pins for higher density
devices.
The TMS input is used to give commands to the TAP controller
and is sampled on the rising edge of TCK. This pin may be left
unconnected if the TAP is not used. The pin is pulled up inter-
nally, resulting in a logic HIGH level.
The boundary scan register is loaded with the contents of the
RAM input and output ring when the TAP controller is in the
Capture-DR state and is then placed between the TDI and TDO
pins when the controller is moved to the Shift-DR state. The
EXTEST, SAMPLE/PRELOAD, and SAMPLE Z instructions can
be used to capture the contents of the input and output ring.
Test Data-In (TDI)
The TDI pin is used to serially input information into the registers
and can be connected to the input of any of the registers. The
register between TDI and TDO is chosen by the instruction that
is loaded into the TAP instruction register. For information on
loading the instruction register, see the TAP Controller State
unconnected if the TAP is unused in an application. TDI is
connected to the most significant bit (MSB) on any register.
the bits are connected. Each bit corresponds to one of the bumps
on the SRAM package. The MSB of the register is connected to
TDI, and the LSB is connected to TDO.
Identification (ID) Register
Test Data-Out (TDO)
The ID register is loaded with a vendor-specific, 32-bit code
during the Capture-DR state when the IDCODE command is
loaded in the instruction register. The IDCODE is hardwired into
the SRAM and can be shifted out when the TAP controller is in
the Shift-DR state. The ID register has a vendor code and other
The TDO output pin is used to serially clock data out from the
registers. The output is active, depending upon the current state
The output changes on the falling edge of TCK. TDO is
connected to the least significant bit (LSB) of any register.
Performing a TAP Reset
A Reset is performed by forcing TMS HIGH (V ) for five rising
TAP Instruction Set
DD
edges of TCK. This Reset does not affect the operation of the
SRAM and can be performed while the SRAM is operating. At
power up, the TAP is reset internally to ensure that TDO comes
up in a high-Z state.
Eight different instructions are possible with the three-bit
instruction register. All combinations are listed in Instruction
RESERVED and must not be used. The other five instructions
are described in this section in detail.
TAP Registers
Instructions are loaded into the TAP controller during the Shift-IR
state when the instruction register is placed between TDI and
TDO. During this state, instructions are shifted through the
instruction register through the TDI and TDO pins. To execute
the instruction once it is shifted in, the TAP controller must be
moved into the Update-IR state.
Registers are connected between the TDI and TDO pins to scan
the data in and out of the SRAM test circuitry. Only one register
can be selected at a time through the instruction registers. Data
is serially loaded into the TDI pin on the rising edge of TCK. Data
is output on the TDO pin on the falling edge of TCK.
Document Number: 001-07161 Rev. *D
Page 13 of 31
CY7C1317CV18, CY7C1917CV18
CY7C1319CV18, CY7C1321CV18
IDCODE
PRELOAD places an initial data pattern at the latched parallel
outputs of the boundary scan register cells before the selection
of another boundary scan test operation.
The IDCODE instruction loads a vendor-specific, 32-bit code into
the instruction register. It also places the instruction register
between the TDI and TDO pins and shifts the IDCODE out of the
device when the TAP controller enters the Shift-DR state. The
IDCODE instruction is loaded into the instruction register at
power up or whenever the TAP controller is supplied a
Test-Logic-Reset state.
The shifting of data for the SAMPLE and PRELOAD phases can
occur concurrently when required, that is, while the data
captured is shifted out, the preloaded data can be shifted in.
BYPASS
When the BYPASS instruction is loaded in the instruction register
and the TAP is placed in a Shift-DR state, the bypass register is
placed between the TDI and TDO pins. The advantage of the
BYPASS instruction is that it shortens the boundary scan path
when multiple devices are connected together on a board.
SAMPLE Z
The SAMPLE Z instruction connects the boundary scan register
between the TDI and TDO pins when the TAP controller is in a
Shift-DR state. The SAMPLE Z command puts the output bus
into a High-Z state until the next command is supplied during the
Update IR state.
EXTEST
The EXTEST instruction drives the preloaded data out through
the system output pins. This instruction also connects the
boundary scan register for serial access between the TDI and
TDO in the Shift-DR controller state.
SAMPLE/PRELOAD
SAMPLE/PRELOAD is a 1149.1 mandatory instruction. When
the SAMPLE/PRELOAD instructions are loaded into the
instruction register and the TAP controller is in the Capture-DR
state, a snapshot of data on the input and output pins is captured
in the boundary scan register.
EXTEST OUTPUT BUS TRI-STATE
IEEE Standard 1149.1 mandates that the TAP controller be able
to put the output bus into a tri-state mode.
The user must be aware that the TAP controller clock can only
operate at a frequency up to 20 MHz, while the SRAM clock
operates more than an order of magnitude faster. Because there
is a large difference in the clock frequencies, it is possible that
during the Capture-DR state, an input or output undergoes a
transition. The TAP may then try to capture a signal while in
transition (metastable state). This does not harm the device, but
there is no guarantee as to the value that is captured.
Repeatable results may not be possible.
The boundary scan register has a special bit located at bit #47.
When this scan cell, called the “extest output bus tri-state,” is
latched into the preload register during the Update-DR state in
the TAP controller, it directly controls the state of the output
(Q-bus) pins, when the EXTEST is entered as the current
instruction. When HIGH, it enables the output buffers to drive the
output bus. When LOW, this bit places the output bus into a
High-Z condition.
To guarantee that the boundary scan register captures the
correct value of a signal, the SRAM signal must be stabilized
long enough to meet the TAP controller's capture setup plus hold
times (t and t ). The SRAM clock input might not be captured
correctly if there is no way in a design to stop (or slow) the clock
during a SAMPLE/PRELOAD instruction. If this is an issue, it is
still possible to capture all other signals and simply ignore the
value of the CK and CK captured in the boundary scan register.
This bit can be set by entering the SAMPLE/PRELOAD or
EXTEST command, and then shifting the desired bit into that cell,
during the Shift-DR state. During Update-DR, the value loaded
into that shift-register cell latches into the preload register. When
the EXTEST instruction is entered, this bit directly controls the
output Q-bus pins. Note that this bit is pre-set HIGH to enable
the output when the device is powered up, and also when the
TAP controller is in the Test-Logic-Reset state.
CS
CH
Once the data is captured, it is possible to shift out the data by
putting the TAP into the Shift-DR state. This places the boundary
scan register between the TDI and TDO pins.
Reserved
These instructions are not implemented but are reserved for
future use. Do not use these instructions.
Document Number: 001-07161 Rev. *D
Page 14 of 31
CY7C1317CV18, CY7C1917CV18
CY7C1319CV18, CY7C1321CV18
TAP Controller State Diagram
The state diagram for the TAP controller follows.
[9]
TEST-LOGIC
1
RESET
0
1
1
1
SELECT
TEST-LOGIC/
SELECT
0
IR-SCAN
IDLE
DR-SCAN
0
0
1
1
CAPTURE-DR
0
CAPTURE-IR
0
0
1
0
1
SHIFT-DR
1
SHIFT-IR
1
EXIT1-DR
0
EXIT1-IR
0
0
0
PAUSE-DR
1
PAUSE-IR
1
0
0
EXIT2-DR
1
EXIT2-IR
1
UPDATE-IR
0
UPDATE-DR
1
1
0
Note
9. The 0/1 next to each state represents the value at TMS at the rising edge of TCK.
Document Number: 001-07161 Rev. *D
Page 15 of 31
CY7C1317CV18, CY7C1917CV18
CY7C1319CV18, CY7C1321CV18
TAP Controller Block Diagram
0
Bypass Register
2
1
1
1
0
0
0
Selection
TDI
Selection
Circuitry
TDO
Instruction Register
Circuitry
31 30
29
.
.
2
Identification Register
.
106
.
.
.
2
Boundary Scan Register
TCK
TMS
TAP Controller
TAP Electrical Characteristics
Over the Operating Range
Parameter
Description
Output HIGH Voltage
Test Conditions
= −2.0 mA
Min
1.4
1.6
Max
Unit
V
V
V
V
V
V
I
I
I
I
I
V
V
OH1
OH2
OL1
OL2
IH
OH
OH
OL
OL
Output HIGH Voltage
Output LOW Voltage
Output LOW Voltage
Input HIGH Voltage
= −100 μA
= 2.0 mA
0.4
0.2
V
= 100 μA
V
0.65V
V
+ 0.3
V
DD
DD
Input LOW Voltage
–0.3
–5
0.35V
5
V
IL
DD
Input and Output Load Current
GND ≤ V ≤ V
DD
μA
X
I
Notes
10. These characteristics pertain to the TAP inputs (TMS, TCK, TDI and TDO). Parallel load levels are specified in the Electrical Characteristics Table.
11. Overshoot: V (AC) < V + 0.85V (Pulse width less than t /2).
/2), Undershoot: V (AC) > −1.5V (Pulse width less than t
IH
DDQ
CYC
IL
CYC
12. All Voltage referenced to Ground.
Document Number: 001-07161 Rev. *D
Page 16 of 31
CY7C1317CV18, CY7C1917CV18
CY7C1319CV18, CY7C1321CV18
TAP AC Switching Characteristics
Over the Operating Range
Parameter
Description
Min
Max
Unit
ns
t
t
t
t
TCK Clock Cycle Time
TCK Clock Frequency
TCK Clock HIGH
50
TCYC
TF
20
MHz
ns
20
20
TH
TCK Clock LOW
ns
TL
Setup Times
t
t
t
TMS Setup to TCK Clock Rise
TDI Setup to TCK Clock Rise
Capture Setup to TCK Rise
5
5
5
ns
ns
ns
TMSS
TDIS
CS
Hold Times
t
t
t
TMS Hold after TCK Clock Rise
TDI Hold after Clock Rise
5
5
5
ns
ns
ns
TMSH
TDIH
CH
Capture Hold after Clock Rise
Output Times
t
t
TCK Clock LOW to TDO Valid
TCK Clock LOW to TDO Invalid
10
ns
ns
TDOV
TDOX
0
TAP Timing and Test Conditions
Figure 2 shows the TAP timing and test conditions.
Figure 2. TAP Timing and Test Conditions
0.9V
ALL INPUT PULSES
1.8V
50Ω
0.9V
TDO
0V
Z = 50
Ω
0
C = 20 pF
L
t
t
TH
TL
GND
(a)
Test Clock
TCK
t
TCYC
t
TMSH
t
TMSS
Test Mode Select
TMS
t
TDIS
t
TDIH
Test Data In
TDI
Test Data Out
TDO
t
TDOV
t
TDOX
Notes
13. t and t refer to the setup and hold time requirements of latching data from the boundary scan register.
CS
CH
14. Test conditions are specified using the load in TAP AC Test Conditions. t /t = 1 ns.
R
F
Document Number: 001-07161 Rev. *D
Page 17 of 31
CY7C1317CV18, CY7C1917CV18
CY7C1319CV18, CY7C1321CV18
Identification Register Definitions
Value
Instruction Field
Description
CY7C1317CV18
CY7C1917CV18
000
CY7C1319CV18
000
CY7C1321CV18
Revision Number
(31:29)
000
000
Version number.
Cypress Device ID 11010100011000101 11010100011001101 11010100011010101 11010100011100101 Defines the type of
(28:12)
SRAM.
Cypress JEDEC ID
(11:1)
00000110100
1
00000110100
1
00000110100
1
00000110100
1
Allows unique
identification of
SRAM vendor.
ID Register
Presence (0)
Indicates the
presence of an ID
register.
Scan Register Sizes
Register Name
Bit Size
Instruction
Bypass
3
1
ID
32
107
Boundary Scan
Instruction Codes
Instruction
EXTEST
Code
000
Description
Captures the input and output ring contents.
IDCODE
001
Loads the ID register with the vendor ID code and places the register between TDI and TDO.
This operation does not affect SRAM operation.
SAMPLE Z
010
Captures the input and output contents. Places the boundary scan register between TDI and
TDO. Forces all SRAM output drivers to a High-Z state.
RESERVED
011
100
Do Not Use: This instruction is reserved for future use.
SAMPLE/PRELOAD
Captures the input and output ring contents. Places the boundary scan register between TDI
and TDO. Does not affect the SRAM operation.
RESERVED
RESERVED
BYPASS
101
110
111
Do Not Use: This instruction is reserved for future use.
Do Not Use: This instruction is reserved for future use.
Places the bypass register between TDI and TDO. This operation does not affect SRAM
operation.
Document Number: 001-07161 Rev. *D
Page 18 of 31
CY7C1317CV18, CY7C1917CV18
CY7C1319CV18, CY7C1321CV18
Boundary Scan Order
Bit #
0
Bump ID
6R
Bit #
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
Bump ID
10G
9G
Bit #
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
Bump ID
6A
5B
5A
4A
5C
4B
3A
1H
1A
2B
3B
1C
1B
3D
3C
1D
2C
3E
2D
2E
1E
2F
Bit #
84
Bump ID
2J
1
6P
85
3K
2
6N
11F
11G
9F
86
3J
3
7P
87
2K
4
7N
88
1K
5
7R
10F
11E
10E
10D
9E
89
2L
6
8R
90
3L
7
8P
91
1M
1L
8
9R
92
9
11P
10P
10N
9P
93
3N
3M
1N
2M
3P
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
10C
11D
9C
94
95
96
10M
11N
9M
9D
97
11B
11C
9B
98
2N
2P
99
9N
100
101
102
103
104
105
106
1P
11L
11M
9L
10B
11A
Internal
9A
3R
4R
4P
10L
11K
10K
9J
5P
8B
5N
5R
7C
3F
6C
1G
1F
9K
8A
10J
11J
11H
7A
3G
2G
1J
7B
6B
Document Number: 001-07161 Rev. *D
Page 19 of 31
CY7C1317CV18, CY7C1917CV18
CY7C1319CV18, CY7C1321CV18
DLL Constraints
Power Up Sequence in DDR-II SRAM
■ DLL uses K clock as its synchronizing input. The input must
have low phase jitter, which is specified as t
DDR-II SRAMs must be powered up and initialized in a
predefined manner to prevent undefined operations.
.
KC Var
■ The DLL functions at frequencies down to 120 MHz.
Power Up Sequence
■ If the input clock is unstable and the DLL is enabled, then the
DLL may lock onto an incorrect frequency, causing unstable
SRAM behavior. To avoid this, provide1024 cycles stable clock
to relock to the desired clock frequency.
■ Apply power and drive DOFF either HIGH or LOW (all other
inputs can be HIGH or LOW).
❐ Apply V before V
.
DD
DDQ
❐ Apply V
before V
or at the same time as V
.
DDQ
REF
REF
❐ Drive DOFF HIGH.
■ Provide stable DOFF (HIGH), power, and clock (K, K) for 1024
cycles to lock the DLL.
Figure 3. Power Up Waveforms
K
K
Unstable Clock
> 1024 Stable clock
Stable)
DDQ
Start Normal
Operation
/
V
Clock Start (Clock Starts after V
DD
Stable (< +/- 0.1V DC per 50ns )
/
/
V
VDDQ
V
VDD
DD
DDQ
Fix High (or tie to V
)
DDQ
DOFF
Document Number: 001-07161 Rev. *D
Page 20 of 31
CY7C1317CV18, CY7C1917CV18
CY7C1319CV18, CY7C1321CV18
Current into Outputs (LOW) ........................................ 20 mA
Static Discharge Voltage (MIL-STD-883, M 3015).... >2001V
Latch up Current..................................................... >200 mA
Maximum Ratings
Exceeding maximum ratings may impair the useful life of the
device. These user guidelines are not tested.
Storage Temperature ................................. –65°C to +150°C
Ambient Temperature with Power Applied.. –55°C to +125°C
Operating Range
Ambient
Range
Commercial
Industrial
Temperature (T )
V
V
DDQ
Supply Voltage on V Relative to GND........–0.5V to +2.9V
A
DD
DD
0°C to +70°C
1.8 ± 0.1V
1.4V to
Supply Voltage on V
Relative to GND.......–0.5V to +V
DD
DDQ
V
DD
–40°C to +85°C
DC Applied to Outputs in High-Z .........–0.5V to V
+ 0.3V
DDQ
DC Input Voltage
.............................. –0.5V to V + 0.3V
DD
Electrical Characteristics
DC Electrical Characteristics
Over the Operating Range
Parameter
Description
Power Supply Voltage
IO Supply Voltage
Test Conditions
Min
1.7
1.4
Typ
Max
Unit
V
1.8
1.5
1.9
V
V
DD
V
V
V
V
V
V
V
I
V
DD
DDQ
OH
Output HIGH Voltage
Output LOW Voltage
Output HIGH Voltage
Output LOW Voltage
Input HIGH Voltage
Input LOW Voltage
Note 16
Note 17
V
V
/2 – 0.12
/2 – 0.12
– 0.2
V
V
/2 + 0.12
/2 + 0.12
V
DDQ
DDQ
DDQ
V
OL
DDQ
I
I
= −0.1 mA, Nominal Impedance
V
V
V
OH(LOW)
OL(LOW)
IH
OH
OL
DDQ
DDQ
= 0.1 mA, Nominal Impedance
V
0.2
V
SS
V
+ 0.1
V
+ 0.3
V
REF
DDQ
–0.3
V
– 0.1
V
IL
REF
Input Leakage Current
Output Leakage Current
Input Reference Voltage
GND ≤ V ≤ V
−5
−5
5
μA
μA
V
X
I
DDQ
I
GND ≤ V ≤ V
Output Disabled
5
OZ
I
DDQ,
V
Typical Value = 0.75V
0.68
0.75
0.95
770
770
810
890
720
720
760
830
670
670
700
765
REF
I
V
Operating Supply
V
= Max,
300 MHz
278 MHz
250 MHz
(x8)
(x9)
mA
DD
DD
DD
I
= 0 mA,
OUT
f = f
= 1/t
MAX
CYC
(x18)
(x36)
(x8)
mA
mA
(x9)
(x18)
(x36)
(x8)
(x9)
(x18)
(x36)
Notes
15. Power up: assumes a linear ramp from 0V to V (min) within 200 ms. During this time V < V and V
< V
DD
.
DD
IH
DD
DDQ
16. Outputs are impedance controlled. I = –(V
/2)/(RQ/5) for values of 175Ω < RQ < 350Ω.
OH
DDQ
17. Outputs are impedance controlled. I = (V
/2)/(RQ/5) for values of 175Ω < RQ < 350Ω.
OL
DDQ
18. V
(min) = 0.68V or 0.46V
, whichever is larger, V
(max) = 0.95V or 0.54V
, whichever is smaller.
REF
DDQ
REF
DDQ
19. The operation current is calculated with 50% read cycle and 50% write cycle.
Document Number: 001-07161 Rev. *D
Page 21 of 31
CY7C1317CV18, CY7C1917CV18
CY7C1319CV18, CY7C1321CV18
Electrical Characteristics (continued)
DC Electrical Characteristics
[12]
Over the Operating Range
Parameter
Description
Test Conditions
200 MHz
Min
Typ
Max
580
580
600
655
515
515
540
600
315
315
325
350
305
305
315
330
300
300
300
320
285
285
290
300
280
280
285
295
Unit
DD
I
V
Operating Supply
V
= Max,
(x8)
(x9)
mA
DD
DD
I
= 0 mA,
OUT
f = f
= 1/t
MAX
CYC
(x18)
(x36)
(x8)
167 MHz
300 MHz
278 MHz
250 MHz
200 MHz
167MHz
mA
mA
mA
mA
mA
mA
(x9)
(x18)
(x36)
(x8)
I
Automatic Power Down
Current
Max V
,
SB1
DD
Both Ports Deselected,
(x9)
V
≥ V or V ≤ V
IN
IH
IN
IL
f = f
Inputs Static
= 1/t
,
(x18)
(x36)
(x8)
MAX
CYC
(x9)
(x18)
(x36)
(x8)
(x9)
(x18)
(x36)
(x8)
(x9)
(x18)
(x36)
(x8)
(x9)
(x18)
(x36)
AC Electrical Characteristics
Over the Operating Range
Parameter
Description
Input HIGH Voltage
Input LOW Voltage
Test Conditions
Min
+ 0.2
REF
Typ
–
Max
Unit
V
V
V
–
IH
IL
V
–
–
V
– 0.2
V
REF
Document Number: 001-07161 Rev. *D
Page 22 of 31
CY7C1317CV18, CY7C1917CV18
CY7C1319CV18, CY7C1321CV18
Capacitance
Tested initially and after any design or process change that may affect these parameters.
Parameter
Description
Input Capacitance
Test Conditions
Max
Unit
pF
C
T = 25°C, f = 1 MHz, V = 1.8V, V = 1.5V
DDQ
5
6
7
IN
A
DD
C
C
Clock Input Capacitance
Output Capacitance
pF
CLK
O
pF
Thermal Resistance
Tested initially and after any design or process change that may affect these parameters.
165 FBGA
Package
Parameter
Description
Test Conditions
Unit
Θ
Thermal Resistance
(Junction to Ambient)
Test conditions follow standard test methods and
procedures for measuring thermal impedance, in
accordance with EIA/JESD51.
18.7
°C/W
JA
Θ
Thermal Resistance
(Junction to Case)
4.5
°C/W
JC
Figure 4. AC Test Loads and Waveforms
V
REF = 0.75V
0.75V
VREF
VREF
0.75V
R = 50Ω
OUTPUT
ALL INPUT PULSES
1.25V
Z = 50Ω
0
OUTPUT
Device
Under
Test
R = 50Ω
L
0.75V
Device
Under
0.25V
5 pF
VREF = 0.75V
Slew Rate = 2 V/ns
ZQ
Test
ZQ
RQ =
RQ =
250Ω
250Ω
INCLUDING
JIG AND
SCOPE
(a)
(b)
Note
20. Unless otherwise noted, test conditions assume signal transition time of 2V/ns, timing reference levels of 0.75V, V
= 0.75V, RQ = 250Ω, V
= 1.5V, input pulse
DDQ
REF
levels of 0.25V to 1.25V, and output loading of the specified I /I and load capacitance shown in (a) of AC Test Loads and Waveforms.
OL OH
Document Number: 001-07161 Rev. *D
Page 23 of 31
CY7C1317CV18, CY7C1917CV18
CY7C1319CV18, CY7C1321CV18
Switching Characteristics
Over the Operating Range
300 MHz
278 MHz
250 MHz
200 MHz
167 MHz
Cypress Consortium
Parameter Parameter
Description
(Typical) to the First Access
DD
Unit
Min Max Min Max Min Max Min Max Min Max
t
t
t
t
t
V
1
–
1
–
1
–
1
–
1
–
ms
ns
ns
ns
ns
POWER
CYC
KH
t
t
t
t
K Clock and C Clock Cycle Time
Input Clock (K/K and C/C) HIGH
Input Clock (K/K and C/C) LOW
3.3 8.4 3.6 8.4 4.0 8.4 5.0 8.4 6.0 8.4
KHKH
KHKL
KLKH
KHKH
1.32
1.32
–
–
–
1.4
1.4
1.6
–
–
–
1.6
1.6
1.8
–
–
–
2.0
2.0
2.2
–
–
–
2.4
2.4
2.7
–
–
–
KL
K Clock Rise to K Clock Rise and C 1.49
to C Rise (rising edge to rising edge)
KHKH
t
t
K/K Clock Rise to C/C Clock Rise 0.00 1.45 0.00 1.55 0.00 1.8 0.00 2.2 0.00 2.7
(rising edge to rising edge)
ns
KHCH
KHCH
Setup Times
t
t
t
t
Address Setup to K Clock Rise
0.4
0.4
–
–
0.4
0.4
–
–
0.5
0.5
–
–
0.6
0.6
–
–
0.7
0.7
–
–
ns
ns
SA
SC
AVKH
IVKH
Control Setup to K Clock Rise
(LD, R/W)
t
t
t
t
Double Data Rate Control Setup to 0.3
Clock (K/K) Rise
–
–
0.3
0.3
–
–
0.35
0.35
–
–
0.4
0.4
–
–
0.5
0.5
–
–
ns
ns
SCDDR
IVKH
(BWS , BWS , BWS , BWS )
0
1
2
3
SD
D
Setup to Clock (K/K) Rise
0.3
DVKH
[X:0]
Hold Times
t
t
t
t
Address Hold after K Clock Rise
0.4
0.4
–
–
0.4
0.4
–
–
0.5
0.5
–
–
0.6
0.6
–
–
0.7
0.7
–
–
ns
ns
HA
HC
KHAX
KHIX
Control Hold after K Clock Rise
(LD, R/W)
t
t
t
t
Double Data Rate Control Hold after 0.3
Clock (K/K) Rise
–
–
0.3
0.3
–
–
0.35
0.35
–
–
0.4
0.4
–
–
0.5
0.5
–
–
ns
ns
HCDDR
HD
KHIX
(BWS , BWS , BWS , BWS )
0
1
2
3
D
Hold after Clock (K/K) Rise
0.3
KHDX
[X:0]
Notes
21. When a part with a maximum frequency above 167 MHz is operating at a lower clock frequency, it requires the input timings of the frequency range in which it is being
operated and outputs data with the output timings of that frequency range.
22. This part has an internal voltage regulator; t
is the time that the power is supplied above V minimum initially before a read or write operation can be initiated.
DD
POWER
23. For DQ2 data signal on CY7C1917CV18 device, t is 0.5 ns for 200 MHz, 250 MHz, 278 MHz, and 300 MHz frequencies.
SD
Document Number: 001-07161 Rev. *D
Page 24 of 31
CY7C1317CV18, CY7C1917CV18
CY7C1319CV18, CY7C1321CV18
Switching Characteristics (continued)
[20, 21]
Over the Operating Range
300 MHz
278 MHz
250 MHz
200 MHz
167 MHz
Cypress Consortium
Parameter Parameter
Description
Unit
Min Max Min Max Min Max Min Max Min Max
Output Times
t
t
t
t
C/C Clock Rise (or K/K in single
clock mode) to Data Valid
–
0.45
–
–
0.45
–
–
0.45
–
–
0.45
–
–
0.50 ns
ns
CO
CHQV
CHQX
Data Output Hold after Output C/C –0.45
Clock Rise (Active to Active)
–0.45
–0.45
–0.45
–0.50
–
DOH
t
t
t
t
C/C Clock Rise to Echo Clock Valid
–
0.45
–
–
0.45
–
–
0.45
–
–
0.45
–
–
0.50 ns
ns
CCQO
CQOH
CHCQV
CHCQX
Echo Clock Hold after C/C Clock
Rise
–0.45
–0.45
–0.45
–0.45
–0.50
–
t
t
t
t
t
t
t
t
Echo Clock High to Data Valid
Echo Clock High to Data Invalid
–
0.27
–
0.27
–
0.30
–
0.35
–
0.40 ns
CQD
CQHQV
CQHQX
CQHCQL
CQHCQH
–0.27
1.24
1.24
–
–
–
–0.27
1.35
1.35
–
–
–
–0.30
1.55
1.55
–
–
–
–0.35
1.95
1.95
–
–
–
–0.40
2.45
2.45
–
–
–
ns
ns
ns
CQDOH
CQH
Output Clock (CQ/CQ) HIGH
CQ Clock Rise to CQ Clock Rise
CQHCQH
(rising edge to rising edge)
t
t
t
Clock (C/C) Rise to High-Z
(Active to High-Z)
–
0.45
–
–
0.45
–
–
0.45
–
–
0.45
–
–
0.50 ns
ns
CHZ
CHQZ
t
Clock (C/C) Rise to Low-Z
–0.45
–0.45
–0.45
–0.45
–0.50
–
CLZ
CHQX1
DLL Timing
t
t
t
t
t
t
Clock Phase Jitter
–
0.20
–
–
0.20
–
–
0.20
–
–
0.20
–
–
0.20 ns
KC Var
KC Var
DLL Lock Time (K, C)
K Static to DLL Reset
1024
30
1024
30
1024
30
1024
30
1024
30
–
–
Cycles
ns
KC lock
KC Reset
KC lock
KC Reset
–
–
–
–
Notes
24. These parameters are extrapolated from the input timing parameters (t
- 250 ps, where 250 ps is the internal jitter. An input jitter of 200 ps (t
) is already
KHKH
KC Var
included in the t
). These parameters are only guaranteed by design and are not tested in production.
KHKH
25. t
, t
are specified with a load capacitance of 5 pF as in (b) of AC Test Loads and Waveforms. Transition is measured ±100 mV from steady-state voltage.
CHZ CLZ
26. At any voltage and temperature t
is less than t
and t
less than t
.
CHZ
CLZ
CHZ
CO
Document Number: 001-07161 Rev. *D
Page 25 of 31
CY7C1317CV18, CY7C1917CV18
CY7C1319CV18, CY7C1321CV18
Switching Waveforms
Figure 5. Read/Write/Deselect Sequence
READ
(burst of 4)
4
READ
(burst of 4)
12
READ
(burst of 4)
2
WRITE
(burst of 4)
8
WRITE
(burst of 4)
10
NOP
1
NOP
6
NOP
7
3
5
9
11
13
K
t
t
t
t
KH KL
CYC
KHKH
K
LD
t
t
SC HC
R/W
A
A4
A2
A3
A0
A1
t
t
t
t
SA HA
HD
HD
t
t
SD
SD
DQ
Q00 Q01 Q02 Q03 Q10 Q11 Q12 Q13
D20 D21 D22 D23 D30 D31 D32 D33
Q40
t
t
CQD
t
CLZ
t
KHCH
CO
t
t
DOH
CQDOH
t
t
KHCH
CHZ
C
C
t
t
t
KH KL
t
KHKH
CYC
t
CCQO
t
CQOH
CQ
CQ
t
t
CQHCQH
CCQO
t
CQH
t
CQOH
DON’T CARE
UNDEFINED
Notes
27. Q00 refers to output from address A0. Q01 refers to output from the next internal burst address following A0, that is, A0 + 1.
28. Outputs are disabled (High-Z) one clock cycle after a NOP.
29. In this example, if address A4 = A3, then data Q40 = D30, Q41 = D31, Q42 = D32, and Q43 = D43. Write data is forwarded immediately as read results. This note
applies to the whole diagram.
Document Number: 001-07161 Rev. *D
Page 26 of 31
CY7C1317CV18, CY7C1917CV18
CY7C1319CV18, CY7C1321CV18
Ordering Information
Not all of the speed, package and temperature ranges are available. Please contact your local sales representative or
Speed
(MHz)
Package
Diagram
Operating
Range
Ordering Code
Package Type
300 CY7C1317CV18-300BZC
CY7C1917CV18-300BZC
CY7C1319CV18-300BZC
CY7C1321CV18-300BZC
CY7C1317CV18-300BZXC
CY7C1917CV18-300BZXC
CY7C1319CV18-300BZXC
CY7C1321CV18-300BZXC
CY7C1317CV18-300BZI
CY7C1917CV18-300BZI
CY7C1319CV18-300BZI
CY7C1321CV18-300BZI
CY7C1317CV18-300BZXI
CY7C1917CV18-300BZXI
CY7C1319CV18-300BZXI
CY7C1321CV18-300BZXI
278 CY7C1317CV18-278BZC
CY7C1917CV18-278BZC
CY7C1319CV18-278BZC
CY7C1321CV18-278BZC
CY7C1317CV18-278BZXC
CY7C1917CV18-278BZXC
CY7C1319CV18-278BZXC
CY7C1321CV18-278BZXC
CY7C1317CV18-278BZI
CY7C1917CV18-278BZI
CY7C1319CV18-278BZI
CY7C1321CV18-278BZI
CY7C1317CV18-278BZXI
CY7C1917CV18-278BZXI
CY7C1319CV18-278BZXI
CY7C1321CV18-278BZXI
51-85180 165-Ball Fine Pitch Ball Grid Array (13 x 15 x 1.4 mm)
51-85180 165-Ball Fine Pitch Ball Grid Array (13 x 15 x 1.4 mm) Pb-Free
51-85180 165-Ball Fine Pitch Ball Grid Array (13 x 15 x 1.4 mm)
51-85180 165-Ball Fine Pitch Ball Grid Array (13 x 15 x 1.4 mm) Pb-Free
51-85180 165-Ball Fine Pitch Ball Grid Array (13 x 15 x 1.4 mm)
51-85180 165-Ball Fine Pitch Ball Grid Array (13 x 15 x 1.4 mm) Pb-Free
51-85180 165-Ball Fine Pitch Ball Grid Array (13 x 15 x 1.4 mm)
51-85180 165-Ball Fine Pitch Ball Grid Array (13 x 15 x 1.4 mm) Pb-Free
Commercial
Industrial
Commercial
Industrial
Document Number: 001-07161 Rev. *D
Page 27 of 31
CY7C1317CV18, CY7C1917CV18
CY7C1319CV18, CY7C1321CV18
Ordering Information (continued)
Not all of the speed, package and temperature ranges are available. Please contact your local sales representative or
Speed
(MHz)
Package
Diagram
Operating
Range
Ordering Code
Package Type
250 CY7C1317CV18-250BZC
CY7C1917CV18-250BZC
CY7C1319CV18-250BZC
CY7C1321CV18-250BZC
CY7C1317CV18-250BZXC
CY7C1917CV18-250BZXC
CY7C1319CV18-250BZXC
CY7C1321CV18-250BZXC
CY7C1317CV18-250BZI
CY7C1917CV18-250BZI
CY7C1319CV18-250BZI
CY7C1321CV18-250BZI
CY7C1317CV18-250BZXI
CY7C1917CV18-250BZXI
CY7C1319CV18-250BZXI
CY7C1321CV18-250BZXI
200 CY7C1317CV18-200BZC
CY7C1917CV18-200BZC
CY7C1319CV18-200BZC
CY7C1321CV18-200BZC
CY7C1317CV18-200BZXC
CY7C1917CV18-200BZXC
CY7C1319CV18-200BZXC
CY7C1321CV18-200BZXC
CY7C1317CV18-200BZI
CY7C1917CV18-200BZI
CY7C1319CV18-200BZI
CY7C1321CV18-200BZI
CY7C1317CV18-200BZXI
CY7C1917CV18-200BZXI
CY7C1319CV18-200BZXI
CY7C1321CV18-200BZXI
51-85180 165-Ball Fine Pitch Ball Grid Array (13 x 15 x 1.4 mm)
51-85180 165-Ball Fine Pitch Ball Grid Array (13 x 15 x 1.4 mm) Pb-Free
51-85180 165-Ball Fine Pitch Ball Grid Array (13 x 15 x 1.4 mm)
51-85180 165-Ball Fine Pitch Ball Grid Array (13 x 15 x 1.4 mm) Pb-Free
51-85180 165-Ball Fine Pitch Ball Grid Array (13 x 15 x 1.4 mm)
51-85180 165-Ball Fine Pitch Ball Grid Array (13 x 15 x 1.4 mm) Pb-Free
51-85180 165-Ball Fine Pitch Ball Grid Array (13 x 15 x 1.4 mm)
51-85180 165-Ball Fine Pitch Ball Grid Array (13 x 15 x 1.4 mm) Pb-Free
Commercial
Industrial
Commercial
Industrial
Document Number: 001-07161 Rev. *D
Page 28 of 31
CY7C1317CV18, CY7C1917CV18
CY7C1319CV18, CY7C1321CV18
Ordering Information (continued)
Not all of the speed, package and temperature ranges are available. Please contact your local sales representative or
Speed
(MHz)
Package
Diagram
Operating
Range
Ordering Code
Package Type
167 CY7C1317CV18-167BZC
CY7C1917CV18-167BZC
CY7C1319CV18-167BZC
CY7C1321CV18-167BZC
CY7C1317CV18-167BZXC
CY7C1917CV18-167BZXC
CY7C1319CV18-167BZXC
CY7C1321CV18-167BZXC
CY7C1317CV18-167BZI
CY7C1917CV18-167BZI
CY7C1319CV18-167BZI
CY7C1321CV18-167BZI
CY7C1317CV18-167BZXI
CY7C1917CV18-167BZXI
CY7C1319CV18-167BZXI
CY7C1321CV18-167BZXI
51-85180 165-Ball Fine Pitch Ball Grid Array (13 x 15 x 1.4 mm)
51-85180 165-Ball Fine Pitch Ball Grid Array (13 x 15 x 1.4 mm) Pb-Free
51-85180 165-Ball Fine Pitch Ball Grid Array (13 x 15 x 1.4 mm)
51-85180 165-Ball Fine Pitch Ball Grid Array (13 x 15 x 1.4 mm) Pb-Free
Commercial
Industrial
Document Number: 001-07161 Rev. *D
Page 29 of 31
CY7C1317CV18, CY7C1917CV18
CY7C1319CV18, CY7C1321CV18
Package Diagram
Figure 6. 165-Ball FBGA (13 x 15 x 1.4 mm), 51-85180
BOTTOM VIEW
PIN 1 CORNER
TOP VIEW
Ø0.05 M C
Ø0.25 M C A B
PIN 1 CORNER
-0.06
Ø0.50 (165X)
+0.14
1
2
3
4
5
6
7
8
9
10
11
11 10
9
8
7
6
5
4
3
2
1
A
B
A
B
C
D
C
D
E
E
F
F
G
G
H
J
H
J
K
K
L
L
M
M
N
P
R
N
P
R
A
A
1.00
5.00
10.00
13.00 0.10
B
13.00 0.10
B
0.15(4X)
NOTES :
SOLDER PAD TYPE : NON-SOLDER MASK DEFINED (NSMD)
PACKAGE WEIGHT : 0.475g
JEDEC REFERENCE : MO-216 / DESIGN 4.6C
PACKAGE CODE : BB0AC
SEATING PLANE
C
51-85180-*A
Document Number: 001-07161 Rev. *D
Page 30 of 31
CY7C1317CV18, CY7C1917CV18
CY7C1319CV18, CY7C1321CV18
Document History Page
Document Title: CY7C1317CV18/CY7C1917CV18/CY7C1319CV18/CY7C1321CV18, 18-Mbit DDR-II SRAM 4-Word
Burst Architecture
Document Number: 001-07161
Submission
Date
Orig. of
Change
Rev. ECN No.
Description of Change
**
433284
462615
See ECN
See ECN
NXR
NXR
New Data Sheet
*A
Changed t and t from 40 ns to 20 ns, changed t
, t
, t , t
, t
,
TH
TL
TMSS TDIS CS TMSH TDIH
t
from 10 ns to 5 ns and changed t
from 20 ns to 10 ns in TAP AC Switching
CH
TDOV
Characteristics table
Modified Power-Up waveform
*B 1523383
See ECN
VKN/AESA Converted from preliminary to final
Updated Logic Block diagram
Updated I /I specs
DD SB
Changed DLL minimum operating frequency from 80MHz to 120MHz
Changed t max spec to 8.4ns
CYC
Modified Switching waveform
Modified footnotes 20 and 28
*C 2507747
*D 2518624
See ECN
See ECN
VKN/PYRS Changed Ambient Temperature with Power Applied from “–10°C to +85°C” to
“–55°C to +125°C” in the “Maximum Ratings“ on page 21
Updated power up sequence waveform and its description
Added footnote #19 related to I
DD
Changed Θ spec from 28.51 to 18.7
JA
Changed Θ spec from 5.91 to 4.5
JC
NXR/PYRS Changed JTAG ID (31:29) from 001 to 000
Sales, Solutions, and Legal Information
Worldwide Sales and Design Support
Cypress maintains a worldwide network of offices, solution centers, manufacturer’s representatives, and distributors. To find the office
closest to you, visit us at cypress.com/sales.
Products
PSoC
PSoC Solutions
General
psoc.cypress.com
clocks.cypress.com
wireless.cypress.com
memory.cypress.com
image.cypress.com
psoc.cypress.com/solutions
psoc.cypress.com/low-power
psoc.cypress.com/precision-analog
psoc.cypress.com/lcd-drive
psoc.cypress.com/can
Clocks & Buffers
Wireless
Low Power/Low Voltage
Precision Analog
LCD Drive
Memories
Image Sensors
CAN 2.0b
USB
psoc.cypress.com/usb
© Cypress Semiconductor Corporation, 2006-2008. The information contained herein is subject to change without notice. Cypress Semiconductor Corporation assumes no responsibility for the use
of any circuitry other than circuitry embodied in a Cypress product. Nor does it convey or imply any license under patent or other rights. Cypress products are not warranted nor intended to be used
for medical, life support, life saving, critical control or safety applications, unless pursuant to an express written agreement with Cypress. Furthermore, Cypress does not authorize its products for use
as critical components in life-support systems where a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress products in life-support
systems application implies that the manufacturer assumes all risk of such use and in doing so indemnifies Cypress against all charges.
Any Source Code (software and/or firmware) is owned by Cypress Semiconductor Corporation (Cypress) and is protected by and subject to worldwide patent protection (United States and foreign),
United States copyright laws and international treaty provisions. Cypress hereby grants to licensee a personal, non-exclusive, non-transferable license to copy, use, modify, create derivative works of,
and compile the Cypress Source Code and derivative works for the sole purpose of creating custom software and or firmware in support of licensee product to be used only in conjunction with a Cypress
integrated circuit as specified in the applicable agreement. Any reproduction, modification, translation, compilation, or representation of this Source Code except as specified above is prohibited without
the express written permission of Cypress.
Disclaimer: CYPRESS MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH REGARD TO THIS MATERIAL, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES
OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. Cypress reserves the right to make changes without further notice to the materials described herein. Cypress does not
assume any liability arising out of the application or use of any product or circuit described herein. Cypress does not authorize its products for use as critical components in life-support systems where
a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress’ product in a life-support systems application implies that the manufacturer
assumes all risk of such use and in doing so indemnifies Cypress against all charges.
Use may be limited by and subject to the applicable Cypress software license agreement.
Document Number: 001-07161 Rev. *D
Revised June 18, 2008
Page 31 of 31
QDR RAMs and Quad Data Rate RAMs comprise a new family of products developed by Cypress, IDT, NEC, Renesas, and Samsung. All product and company names mentioned in this document
are the trademarks of their respective holders.
|