®
Digital I/O
PCIDIO 24H
High-Density, PCI-Bus, Parallel Digital Board with
24 Channels, 24mA/Channel Sink
PCIDIO 48H
High-Density, PCI-Bus, Parallel Digital Board with
48 Channels, 24mA/Channel Sink
PCIDIO 96H
High-Density, PCI-Bus, Parallel Digital Board with
96 Channels, 24mA/Channel Sink
USER’S MANUAL
VER. 2.5 • OCT 2000
&
No part of this manual may be reproduced without permission.
CyberResearch®, Inc.
25 Business Park Dr., Branford, CT 06405 USA
203-483-8815 (9am to 5pm EST) FAX: 203-483-9024
©Copyright 2003
All Rights Reserved.
October 2000
The information in this document is subject to change without prior notice in order
to improve reliability, design, and function and does not represent a commitment
on the part of CyberResearch, Inc.
In no event will CyberResearch, Inc. be liable for direct, indirect, special,
incidental, or consequential damages arising out of the use of or inability to use
the product or documentation, even if advised of the possibility of such damages.
This document contains proprietary information protected by copyright. All rights
are reserved. No part of this manual may be reproduced by any mechanical,
electronic, or other means in any form without prior written permission of
CyberResearch, Inc.
TRADEMARKS
“CyberResearch,” “PCIDIO 24H,” “PCIDIO 48H,” and “PCIDIO 96H” are trademarks
of CyberResearch, Inc. Other product names mentioned herein are used for
identification purposes only and may be trademarks and/or registered trademarks
of their respective companies.
• NOTICE •
CyberResearch, Inc. does not authorize any CyberResearch product for use in life
support systems, medical equipment, and/or medical devices without the written
approval of the President of CyberResearch, Inc. Life support devices and
systems are devices or systems which are intended for surgical implantation into
the body, or to support or sustain life and whose failure to perform can be
reasonably expected to result in injury. Other medical equipment includes devices
used for monitoring, data acquisition, modification, or notification purposes in
relation to life support, life sustaining, or vital statistic recording. CyberResearch
products are not designed with the components required, are not subject to
the testing required, and are not submitted to the certification required to ensure
a level of reliability appropriate for the treatment and diagnosis of humans.
Table of Contents
Chapter 1 Introduction.............................................................. 1
1.1
1.1.1
1.1.2
1.1.3
Features.........................................................................................................2
Digital I/O Ports.....................................................................................2
Timer/Counter and Interrupt System..............................................2
Miscellaneous ......................................................................................2
1.2
1.3
1.4
Applications...................................................................................................2
Specifications ...............................................................................................3
Software Support.........................................................................................4
1.4.1
1.4.2
1.4.3
1.4.4
1.4.5
1.4.6
Programming Library .........................................................................4
PCI LVIEW: LabVIEW® Driver ..........................................................5
PCI VEE: HP-VEE Driver ..................................................................5
PCI DAQB: ActiveX Controls...........................................................5
DASYLabTM PRO.................................................................................5
PCI DDE: DDE Server and InTouchTM...........................................5
Chapter 2 Installation................................................................ 7
2.1
2.2
2.3
What You Have..............................................................................................7
Unpacking......................................................................................................8
PCB Layout....................................................................................................9
2.3.1
2.3.2
2.4
2.5
2.6
PCIDIO 48H/24H PCB Layout..........................................................9
PCIDIO 96H PCB Layout ................................................................10
Hardware Installation................................................................................11
Device Installation for Windows Systems...........................................12
Connector Pin Assignment......................................................................13
2.6.1
Pin Assignment of PCIDIO 24H/48H/96H.....................................13
2.7
Jumpers Description ................................................................................17
2.7.1
2.7.2
2.8
Power on Status of Ports.................................................................17
12V Power Supply Configuration ..................................................18
Termination Boards Connection ............................................................18
Table of Contents
i
·
Chapter 3 Registers Format................................................... 20
3.1
3.2
PCI PnP Registers......................................................................................20
I/O Address Map.........................................................................................21
Chapter 4 Operation Theorem............................................... 22
4.1
4.1.1
4.1.2
4.1.3
4.1.4
4.1.5
4.1.6
4.1.7
Digital I/O Ports...........................................................................................22
Introduction.........................................................................................22
8255 Mode 0........................................................................................22
Special Function of the DIO Signals..............................................22
Digital I/O Port Programming..........................................................23
Control Word.......................................................................................23
Power on Configuration...................................................................24
Note for Output Data.........................................................................24
4.2
4.2.1
4.2.2
4.2.2
4.2.3
Timer/Counter Operation.........................................................................25
Introduction.........................................................................................25
General Purpose Timer/Counter....................................................25
Cascaded 32 Bits Timer...................................................................26
Event Counter and Edge Control...................................................26
4.3
4.3.1
4.3.2
4.3.3
4.3.4
Interrupt Multiplexing................................................................................26
Architecture........................................................................................26
IRQ Level Setting...............................................................................27
Note for Dual Interrupts ...................................................................27
Interrupt Source Control..................................................................28
4.4
12V and 5V Power Supply........................................................................29
Chapter 5 C/C++ Libraries...................................................... 30
5.1
5.2
Libraries Installation................................................................................30
Programming Guide ..................................................................................31
5.2.1
5.2.2
5.3
5.4
5.5
5.6
5.7
5.8
Naming Convention...........................................................................31
Data Types ..........................................................................................31
_DIO48H/96H_Initial.................................................................................32
Digital Input..................................................................................................33
Digital Output...............................................................................................35
Configuration Port......................................................................................36
Configuration Channel..............................................................................37
Set Interrupt Control..................................................................................39
Timer Start...................................................................................................40
Timer Read..............................................................................................41
Timer Stop...............................................................................................42
Cascaded Timer.....................................................................................43
5.9
5.10
5.11
5.12
ii · Table of Contents
5.13
5.14
5.15
5.16
5.17
Get IRQ Status.........................................................................................44
Clear IRQ..................................................................................................45
Software Reset.......................................................................................45
Interrupt Start under Windows...........................................................46
Interrupt Stop under Windows...........................................................47
Product Service ...................................................................... 48
Warranty ................................................................................. 49
Table of Contents iii
·
How to Use This Guide
This manual is designed to help you use the 24H/48H/96H series products. It
describes how to modify and control various functions on the cards to meet
your requirements. It is divided into five chapters:
l
l
Chapter 1, Introduction, gives an overview of the product features.
applications, and specifications.
Chapter 2, Installation, describes how to install the 24H/48H/96H series
products. The layout of are shown, the jumper settings, the connectors
specifications, and the notes for installation are described.
l
Chapter 3, Registers Format, describes the low-level register structure
and format of the PCIDIO 24H/48H/96H.
lChapter 4, Operation Theorem, describes more details about the
versatile functions, including DIO, timer / counter, and interrupt systems.
l
Chapter 5, C/C++ Library specifies the software library of C language
under DOS environment that makes you can operate the functions on
this card easily.
1
Introduction
The PCIDIO 24H/48H/96H series products are general purpose digital I/O cards.
This series includes three cards:
l PCIDIO 24H: 24-CH DIO card
l PCIDIO 48H: 48-CH DIO card
l PCIDIO 96H: 96-CH DIO card
The 48H series products are multi-function digital I/O boards used for
industrial PC with a PCI bus. The cards are plug-and-play, therefore it is
not necessary to set any jumpers for configuration of I/O address or interrupt
resources.
PCIDIO 48H and PCIDIO 96H are 48-channel and 96-channel DIO cards
respectively. PCIDIO 24H is a reduced version of PCIDIO 48H, all the functions
are exactly the same as PCIDIO 48H except there are 24 channels only.
The PCIDIO 48H emulates two industry standard 8255 Programmable
Peripheral Interface (PPI) chips operated under mode zero configuration.
The PCIDIO 96H emulates four PPI chips. These two cards are compatible
not only on hardware connectors but also on software programming.
Every PPI connector offers has 3 ports: PA, PB, and PC. The PC can also be
subdivided into 2 nibble-wide ( 4-bit) ports - PC Upper and PC Low. Each
connector is corresponding to one PPI chip with 24 DIO points.
Introduction
1
·
PCIDIO 24H/48H/96H are equipped with 1,2, and 4 50-pin male ribbon
connectors respectively.
1.1
Features
The 24H/48H/96H series products provide the following advanced features:
1.1.1 Digital I/O Ports
l 24/48/96 TTL/DTL compatible digital I/O lines
l Emulates industry standard mode 0 of 8255 PPI
l Buffered circuits for higher driving
l Direct interface with OPTO-22 compatible I/O module
l Output status read-back
1.1.2 Timer/Counter and Interrupt System
l A 32 bits timer to generate watchdog timer interrupt
l A 16 bits event counter to generate event interrupt
l Programmable interrupt source
l Dual interrupt system
1.1.3 Miscellaneous
l Provide 12V and 5V power supply on OPTO-22 connectors
l On board resettable fuses to protect power supply for external devices
1.2
Applications
l Programmable mixed digital input & output
l Industrial monitoring and control
l Digital I/O control
l Contact closure, switch/keyboard monitoring
l Connects with OPTO-22 compatible modules
l Useful with A/D and D/A to implement a data acquisition & control
system
2 · Introduction
1.3
Specifications
I/O channels
24-bit for PCIDIO 24H
48-bit for PCIDIO 48H
96-bit for PCIDIO 96H
Digital Input Signal
Digital Output Signal
Logic High Voltage:2.0 V to 5.25V
Logic Low Voltage: 0.0 V to 0.80V
Logic High Current: 20.0 uA
Logic Low Current: -0.2 mA
Logic High Voltage: Minimum 2.4 V
Logic Low Voltage: Maximum 0.5V
Logic High Current: -15.0 mA
Logic Low Current: 24.0 mA
Operating Temperature
Storage Temperature
Humidity
0 C ~ 60 C
°
°
-20 C ~ 80 C
°
°
5% ~ 95% non-condensing
I/O Connectors
50-pin male ribbon cable connectors for
PCIDIO 24H/48H/96H or
Bus
PCI bus for PCIDIO 24H/48H/96H
Power Consumption
PCIDIO 24H :
(without external devices) 330mA @5VDC (Typical)
350mA @5VDC (Maximum)
PCIDIO 48H:
500mA @5VDC (Typical)
540mA @5VDC (Maximum)
PCIDIO 96H:
860mA @5VDC (Typical)
940mA @5VDC (Maximum)
Transfer Rate
PCB Dimension
500 K bytes/sec (Maximum)
PCIDIO 24H : 148mm x 102mm
PCIDIO 48H: 148mm x 102mm
PCIDIO 96H: 166mm x 102mm
Introduction
3
·
1.4
Software Support
CyberResearch provides versatile software drivers and packages for users’
different approach to built-up a system. We not only provide programming
library such as DLL for many Windows systems, but also provide drivers for
many software package such as LabVIEW®, HP VEETM, DASYLabTM
,
and InTouchTM
.
All the software options are included with the software CD. Some
software drivers are protected with a serial licensed code. Without the
software serial number, you can still install them and run the demo version
for two hours for demonstration purposes. Please contact CyberResearch
to purchase the formal license serial code.
1.4.1 Programming Library
For customers who are writing their own programs, we provide function
libraries for many different operating systems, including:
l DOS Library: Borland C/C++ and Microsoft C++, the functions
descriptions are included in this user’s guide.
l
l
Windows 95 DLL: For VB, VC++, Delphi, BC5, the functions descriptions
are included in this user’s guide.
PCI DASK: Include device drivers and DLL for Windows 98, Windows
N, Windows 2000 and XP. DLL is binary compatible across Windows 98,
Windows NT, Windows 2000 and XP. That means all applications
developed with PCI DASK are compatible across Windows 98,
Windows NT, Windows 2000 and XP. The developing environment can be
VB, VC++, Delphi, BC5, or any Windows programming language that
allows calls to a DLL. The user’s guide and function reference manual
of PCI DASK are in the CD. Please refer the PDF manuals under
the following directory: \\Manuals\
l The above software drivers are shipped with the board. Please refer to
the “Software Installation Guide” to install these drivers.
4 · Introduction
1.4.2 PCI LV: LabVIEW® Driver
PCI LV contains the VIs, which are used to interface with NI’s
LabVIEW® software package. The PCI LV supports Windows
95/98/NT/2000. The LabVIEW® drivers are free and shipped with the board.
You can install and use them without license. For detail information about
PCI LV, please refer to the user’s guide on the CD.
(\\Manuals\PCI LV 1-2.pdf)
1.4.3 PCI VEE: HP-VEE Driver
The PCI VEE includes the user objects, which are used to interface with
HP VEE software package. PCI VEE supports Windows 95/98/NT. The
HP-VEE drivers are free shipped with the board. You can install and use
them without license. For detail information about PCI VEE, please refer
to the user’s guide in the CD.
(\\Manuals\PCI VEE Man_d.pdf)
1.4.4 PCI DAQB: ActiveX Controls
We suggest the customers who are familiar with ActiveX controls and
VB/VC++ programming use the PCI DAQB ActiveX Control components
library for developing applications. The PCI DAQB is designed under
Windows NT/98. For more detailed information about PCI DAQB, please
refer to the user’s guide on the CD.
(\\Manual_PDF\Software\PCI DAQB\PCI DAQB Manual.pdf)
1.4.5 DASY PRO
DASY PRO is an easy-to-use software package, which provides easy-setup
instrument functions such as FFT analysis. Please contact us to get
DASY PRO, which includes DASYLab and CyberResearch® hardware drivers.
1.4.6 PCI DDE: DDE Server and InTouchTM
DDE stands for Dynamic Data Exchange specifications. The PCI DDE
includes the PCI cards’ DDE server. The PCI DDE server is included with
the CD. It requires a license. The DDE server can be used
conjunction with any DDE client under Windows NT.
Introduction
5
·
6 · Introduction
2
Installation
This chapter describes how to install the 24H/48H/96H series products. At first,
the contents in the package and unpacking information that you should be
careful of are described.
l Check what you have (section 2.1)
l Unpacking (section 2.2)
l Check the PCB (section 2.3)
l Hardware installation (section 2.4)
l Device Installation for Windows System (section 2.5)
l Connector pin assignment (section 2.6)
l Jumpers setup (section 2.7)
l Termination boards connection (section 2.8)
2.1
What You Have
In addition to this User's Manual, the package includes the following items:
l The PCI board
l CyberResearch®CD
l Software Installation Guide
If any of these items is missing or damaged, contact CyberResearch immediately.
Be sure to save the shipping materials and carton in case the item is returned,
or you want to ship or store the product in the future.
Installation
7
·
2.2
Unpacking
Your card contains sensitive electronic components that can be easily
damaged by static electricity.
The card should be put on a grounded anti-static mat. The operator should
wear an anti-static wristband, grounded at the same point as the anti-static
mat.
Inspect the card module carton for obvious damage. Shipping and
handling may cause damage to your module. Be sure there is no shipping
and handling damage on the module before processing.
After opening the card module carton, extract the system module and place
it only on a grounded anti-static surface with components side up.
Again inspect the module for damages. Press down on all the socketed
IC's to make sure that they are properly seated. Do this only with the
module place on a firm flat surface.
Note: DO NOT APPLY POWER TO THE CARD IF IT HAS BEEN DAMAGED.
You are now ready to install your 24H/48H/96H series product.
8 · Installation
2.3
PCB Layout
2.3.1 PCIDIO 48H/24H PCB Layout
Figure 2.3.1 PCIDIO 48H/24H PCB Layout
Installation
9
·
2.3.2 PCIDIO 96H PCB Layout
PCI
Controller
CN1 CN2
CN3 CN4
Figure 2.3.2 PCIDIO 96H PCB Layout
10 · Installation
2.4
Hardware Installation
PCI configuration
The PCI cards are equipped with a plug and play PCI controller,
it can request base addresses and interrupts in accordance with the PCI
standard. The system BIOS will install the system resource based on the
PCI cards’ configuration registers and system parameters (which are set
by system BIOS). Interrupt assignment and memory usage (I/O port
locations) of the PCI cards can be assigned by system BIOS only. These
system resource assignments are done on a board-by-board basis. It is
not suggested to assign the system resource by any other methods.
PCI slot selection
The PCI card can be inserted to any PCI slot without any configuration for
system resource. Please note that the PCI system board and slot must
provide bus-mastering capability to operate this board properly.
PCI Installation Procedures
1. Turn off your computer
2. Turn off all accessories (printer, modem, monitor, etc.) connected
to
your computer.
3. Remove the cover from your computer.
4. Set up jumpers on the PCI card.
5. Select a 32-bit PCI slot. PCI slots are shorter than ISA or EISA slots, and
are usually white or ivory.
6. Before handling the PCI cards, discharge any static buildup on your
body by touching the metal case of the computer. Hold the edge and do
not touch the components.
7. Position the board into the PCI slot you selected.
8. Secure the card in place at the rear panel of the system.
Installation 11
·
2.5 Device Installation for Windows Systems
Once Windows 95/98/2000/XP has started, the Plug and Play function of
Windows system will find the new PCIDAQ cards. If this is the first
time you're installing a PCIDAQ card in your Windows system, you will be
prompted to input the device information source. Please refer to the
“Software Installation Guide” for the steps of installing the device.
12 · Installation
2.6
Connector Pin Assignment
2.6.1 Pin Assignment of PCIDIO 24H/48H/96H
The I/O ports of PCIDIO 24H/48H/96H emulate the mode 0 configuration of
the 8255 general purpose programmable peripheral interface. The cards
come equipped with 50-pin male IDC connectors that interface with OPTO-
22. Figure 2.4 shows the circuits and pinout of PCIDIO 24H/48H/96H's
connectors (CN1~CN4) .
JPn
1
2
3
+12V
FUSE
CNn
1
PnC7
2
PnC6
PnC5
3
5
4
6
PnC4
PnC3
7
9
8
10
PnC2
PnC1
11
13
12
14
PnC0
PnB7
15
17
16
18
PnB6
PnB5
19
21
20
22
PnB4
PnB3
23
25
24
26
PnB2
PnB1
27
29
28
30
PnB0
PnA7
31
33
32
34
PnA6
PnA5
35
37
36
38
PnA4
PnA3
39
41
40
42
PnA2
PnA1
43
45
44
46
PnA0
47
49
48
50
HEADER 25X2
+5V
FUSE
Figure 2.6.1 pin assignments and power signals of PCIDIO 24H/48H/96H
Installation 13
·
2.6.1 Continued
Figure 2.6.1 pin assignments and power signals of PCIDIO 24H/48H/96H
The DIO pin names are specified as PnXb, where
n : means the connector reference number n=1~4.
X : means the port name, X= ‘A’ , ‘B’ or ‘C’
b : means the bit number of a port, b=0~7
For example, P1C4 means bit 4 of port C on connector CN1.
Note: 1. The pinout of the CN1 ~ CN4 connectors are identical.
2. The power supply pins are protected by resetable fuses. Refer to
section 4.4 for details of the power supply.
14 · Installation
For Your Notes
Installation 15
·
For Your Notes
16 · Installation
2.7
Jumpers Description
The 48H/96H DIO cards are ‘plug-and-play’, thus it is not necessary to setup
the card configurations to fit the computer system. However, to fit users’
versatile operation environment, there are still a few jumpers to set the
power-on status of ports and the usage of the +12V output pins.
2.7.1 Power on Status of Ports
For every port on the PCIDIO 48H/96H cards, the power-on status is set as input,
therefore, the voltage could be pulled high, pulled low, or floating. It is
dependent on the jumper setting. Table 2.1 lists the reference number of
the jumpers and the corresponding port names.
Jumper
JA1
Port Name
Remarks
for PCIDIO 24H/48H/96H
P1A (Port A of CN1)
for PCIDIO 24H/48H/96H,
JB1
JC1
P1B (Port B of CN1)
P1C (Port C of CN1)
for PCIDIO 24H/48H/96H,
JA2
JB2
JC2
JA3
JB3
JC3
JA4
JB4
JC4
P2A (Port A of CN2)
P2B (Port B of CN2)
P2C (Port C of CN2)
P3A (Port A of CN3)
P3B (Port B of CN3)
P3C (Port C of CN3)
P4A (Port A of CN4)
P4B (Port B of CN4)
P4C (Port C of CN4)
for PCIDIO 48H/96H
for PCIDIO 48H/96H
for PCIDIO 48H/96H
for PCIDIO 96H
for PCIDIO 96H
for PCIDIO 96H
for PCIDIO 96H
for PCIDIO 96H
for PCIDIO 96H
Table 2.1 Jumpers and Port names list
The physical meaning of all the jumpers are identical. The power on status
of each port can be set independently. The default is to pull all signals high.
The following diagram uses JA1 as an example to show the possible
configurations.
1. Port A of CN1 are power-on pulled high. ‘H’
1
2
JA1
2. Port A of CN1 are power-on pulled low. ‘L’
JA1
1
2
3. Port A of CN1 are power-on floating. (The jumper is removed)
JA1
1
2
Installation 17
·
2.7.2 12V Power Supply Configuration
Pin 2 and pin 4 of the CN1 ~ CN4 50-pin OPTO-22 connectors can be
configured as 12V power supply or ground. Please refer to Figure 2.4 for
the 12 volts power supply position. JP1~JP4 of the 12V power are for
CN1~CN4 respectively. Connections with ground are set as default. The
following diagram shows the setting of JP2, connecting the pin 2 and pin 4
of CN2 to ground.
(12V)1
2(Ground) JP2
2.8
Termination Boards Connection
There are many termination boards that can connect with PCIDIO 48H/96H
for isolated I/O expansion.
1. TB 24R/12, TP DIN024R-24
The TB 24R/12 and TP DIN024R-24 provide 24 Form C relays for digital output control.
PCIDIO 96H
PCIDIO 48H
TB 24R/12
or TP DIN024R-24
2. TB 24P, TP 5024ISO
The TB 24P and TP 5024ISO provide 24 opto-isolated digital input channels.
PCIDIO 96H
TB 24P
PCIDIO 48H
or TP 5024ISO
18 · Installation
For Your Notes
Installation 19
·
Intentionally Blank
3
Registers Format
Detailed descriptions of the register's format are specified in this
chapter. This information is quite useful for the programmers who wish to
handle the card through low-level programming. However, we suggest
users understand more about the PCI interface before beginning any low-level
programming. In addition, the contents of this chapter can help users
understand how to use a software driver to manipulate this card.
3.1
PCI PnP Registers
This PCI card functions as a 32-bit PCI target device to any master on the
PCI bus. There are three types of registers: PCI Configuration Registers
(PCR), Local Configuration Registers (LCR) and PCIDAC 082 registers.
The PCR, which is compliant with PCI-bus specifications, is initialized
and controlled by the plug & play (PnP) PCI BIOS. User's can study the PCI
BIOS specification to understand the operation of the PCR.
The PCI bus controller PCI-9050 is provided by PLX technology Inc.
technology’s web site to download relative information. It is not necessary
for users to understand the details of the LCR if you use the software library.
The PCI PnP BIOS assigns the base address of the LCR. The assigned
address is located at offset 14h of PCR.
The PCIDAC 0812 registers are shown in the next section. The base address,
which is also assigned by the PCI PnP BIOS, is located at offset 18h of
PCR. Therefore, users can read the 18h of PCR to know the base address
by using the BIOS function call.
Please do not try to modify the base address and interrupt which assigned
by the PCI PnP BIOS, it may cause a resource conflict in your system.
20 · Registers Format
3.2
I/O Address Map
All the 48H registers are 8 bits. The users can access these registers
only by 8 bits I/O instructions. The following table shows the registers map,
including descriptions and their offset addresses relative to the base
address. Please refer to the chapter 4 for more detailed operation of every
registers.
Offset
Write
Read
Boards
0x00
0x01
0x02
0x03
0x04
0x05
0x06
0x07
0x08
0x09
0x0A
0x0B
0x0C
0x0D
0x0E
0x0F
0x10
0x11
0x12
P1A
P1B
P1C
P1Ctrl
P2A
P1A
P1B
P1C
Not used
P2A
P2B
P2C
Not used
P3A
P3B
P3C
Not used
P4A
P4B
P4C
PCIDIO 24H
PCIDIO 48H
PCIDIO 96H
PCIDIO 48H
PCIDIO 96H
P2B
P2C
P2Ctrl
P3A
P1AE(1)
P1BE (1)
PCIDIO 96H
P3B
P3C
P3Ctrl
P4A
P4B
P4C
P4Ctrl
P1CE (1) (1) doesn't apply to
Not used PCIDIO series
P2AE (1)
P2BE (1)
P2CE (1)
Not used
Not used
Timer/Counter #0
Timer/Counter #1
Timer/Counter #2
Timer/Counter
Mode Control
Timer/Counter #0
Timer/Counter #1
Timer/Counter #2
Timer/Counter
Mode Status
PCIDIO 24H
PCIDIO 48H
PCIDIO 96H
0x13
not applicable
ISC: Interrupt
Source Control
Clear Interrupt
0x20
0x30
Not used
Not used
Registers Format · 21
4
Operation Theorem
4.1
Digital I/O Ports
4.1.1 Introduction
The 48H/96H products can emulate one/two/four mode 0 configuration of
8255 programmable peripheral interface (PPI) chips. There are 24 DIO
signals for every PPI.
4.1.2 8255 Mode 0
The basic functions of 8255 mode 0 are:
l Two 8-bit I/O ports- - port A (PA) and port B (PB)
l Two nibble-wide (4-bit) ports C- - PC upper and PC lower
l Each port can be used as either input or output
l Outputs are latched whereas inputs are buffered
l 16 different input/output configurations are available
4.1.3 Special Function of the DIO Signals
Two I/O signals (PC0 and PC3) of CN1 and CN2 can be used to generate
hardware interrupt. Refer to section 4.3 for details about the interrupt
control. In addition, the P1C4 signals can be used as input signal of event
counter.
22 · Operation Theorem
4.1.4 Digital I/O Port Programming
Users can write the digital output value to or read back the digital signal
level from the PPI ports by using the software library. Here we define the
port name in Table 4.1. These port names are used both in software library
and all through this manual. The programming for PCIDIO 24H/48H
and PCIDIO 96H are fully compatible.
Connector
Numbers
CN1
CN2
CN3
CN4
P1A
P1B
P2A
P2B
P3A
P3B
P4A
P4B
Port
Names
P1C
P2C
P3C
P4C
P1CTRL
P2CTRL
P3CTRL
P4CTRL
Table 4.1 I/O Port Names
There are four ports on every 8255 PPI, including port A,B,C and the control
port. PA, PB and PC could be written or read but the control port is write
only. Refer to chapter 5 for details about programming of DIO ports.
4.1.5 Control Word
The control word written in the control port is used to setup PA, PB and PC
as input or output port. Figure 4.1 shows the format of the control word.
Table 4.2 shows the 16 possible control words and the respective I/O
configurations .
D7 D6 D5 D4 D3 D2 D1 D0
? ?
X X X ? ? X
1/0 : Input/Output of Port C low nibble
1/0 : Input/Output of Port B
1/0 : Input/Output of Port C high nibble
1/0 : Input/Output of Port A
X : don't care
Figure 4.1 Control Word Format
Operation Theorem · 23
Control
Word
00H
01H
02H
03H
08H
09H
0AH
0BH
10H
11H
12H
13H
18H
19H
1AH
D
4
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
D
3
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
D
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
D
0
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
PORT
A
PORT C
UPPER
O/P
O/P
O/P
O/P
I/P
I/P
I/P
I/P
O/P
O/P
O/P
O/P
I/P
PORT
B
O/P
O/P
I/P
PORT C
LOWER
O/P
I/P
O/P
I/P
O/P
I/P
O/P
I/P
O/P
I/P
O/P
I/P
O/P
I/P
O/P
I/P
O/P
O/P
O/P
O/P
O/P
O/P
O/P
O/P
I/P
I/P
I/P
I/P
I/P
I/P
O/P
O/P
I/P
I/P
O/P
O/P
I/P
I/P
O/P
O/P
I/P
I/P
I/P
I/P
I/P
I/P
I/P
1BH*
I/P
Table 4.2 Summary of control word (D0 - D4)
(* power on default configuration)
4.1.6 Power on Configuration
The default configuration after power on, hardware reset or software reset
sets all ports as input ports, and therefore, users don’t have to worry about
damaging the external devices when system is power on. In addition, the
default signal level can be pulled high or pulled low by setting the jumpers.
Refer to section 2.7 for setting the power on status of the DIO ports.
4.1.7 Note for Output Data
Be careful of the initial condition of digital output signals. If users set the
control word as output port after power on, the previous uncertain output
value will be put on the output pins immediately. Therefore, BE SURE TO
WRITE A SAFE VALUE TO THE PORTS BEFORE CONFIGURING THEM AS
OUTPUT PORTS.
24 · Operation Theorem
4.2
Timer/Counter Operation
4.2.1 Introduction
One 8254 programmable timer/counter chip is installed in 48H/96H series.
There are three counters in one 8254 chip and 6 possible operation modes
for each counter. The block diagram of the timer/counter system is shown
in Figure 4.2.
8254 Chip
Trigger
Edge
Control
P1C4
C
G
C
G
C
G
Event IRQ
Timer IRQ
Counter #0
Timer #1
Timer #2
O
O
O
'H'
'H'
'H'
2 MHz Clock
Figure 4.2 Timer/counter system of 48H/96H series.
The timer #1 and timer #2 of the 8254 chip are cascaded as a 32-bit
programmable timer. In software library, the timer #1 and #2 are always
set as mode 2 (rate generator).
In software library, the counter #0 is used as an event counter, that is,
interrupt on terminal count of 8254 mode 0 . Please refer to chapter 5 for
programming the timer/counter functions.
4.2.2 General Purpose Timer/Counter
The counter 0 is a general purpose timer/counter for users applications. It
can be used as an event counter, or used for measuring frequency, or other
functions. The following Mode are provided by the 82C54 chip.
l Mode 0: Interrupt on Terminal Count
l Mode 1: Programmable One-Shot.
l Mode 2: Rate Generator.
l Mode 3: Square Wave Rate Generator.
l Mode 4: Software Triggered Strobe.
l Mode 5: Hardware Triggered Strobe.
Operation Theorem · 25
The 8254 timer/ counter IC occupies 4 I/O address. Users can refer to
Tundra's or Intel's data sheet for a full description of the 8254 features. You
can download the 8254 data sheet from the following web site:
or
4.2.2 Cascaded 32 Bits Timer
The input clock frequency of the cascaded timers is 2MHz. The output of the
timer is send to the interrupt circuit (refer to section 4.3). Therefore, the
maximum and minimum watchdog timer interrupt frequency is
(2MHz)/(2*2)=500KHz
respectively.
and
(2MHz)/(65535*65535)=
0.000466Hz
4.2.3 Event Counter and Edge Control
The counter #0 of the 8254 chip can be used as an event counter. The
input of counter #0 is PC4 of CN1 (P1C4). The counter clock trigger
direction (H to L or L to H) is programmable. The gate control is always
enabled. The output is send to interrupt system which named as event IRQ.
If counter #0 is set as 8254 mode 0, the event counter IRQ will generate
when the counter value is counting down to zero.
4.3
Interrupt Multiplexing
4.3.1 Architecture
The 48H/96H series products have a powerful and flexible interrupt
multiplexing circuit which is suitable for many applications. The board
could accept Dual Interrupts. The dual interrupt means that the hardware
can generate two interrupt request signals at the same time and the
software can service these two request signals by ISR. Note that the dual
interrupts do not mean that the card occupies two IRQ levels.
The two interrupt request signals (INT1 and INT2) comes from digital input
signals or the timer/counter output. An interrupt source multiplexer (MUX) is
used to select the IRQ sources. Fig 4.3 shows the interrupt system.
26 · Operation Theorem
4.3.2 IRQ Level Setting
There is only one IRQ level requested by this card, although it is a dual
interrupt system. The motherboard circuits will transfer INTA# to one of the
PC IRQ levels. The IRQ level is set by the PCI plug and play BIOS and
saved in the PCI controller. Users can get the IRQ level setting by software
library.
P1C0
~P1C0 & P1C3
Event Counter
INT1
INT2
INT1
MUX
IRQ
Flip-
Flops
PCI
Controller
INTA#
INT2
MUX
P2C0 (*)
~P2C0 & P2C3 (*)
Timer IRQ
Clear IRQ
Fig 4.3 Dual Interrupt System of PCIDIO 24H/48H/96H
(*) Note: This interrupt is not available in PCIDIO 24H
4.3.3 Note for Dual Interrupts
The PCI controller of PCIDIO 24H/48H/96H can receive two hardware IRQ
sources. However, a PCI controller can generate only one IRQ to PCI bus,
the two IRQ sources must be distinguished by the ISR of the application
software if the two IRQs are both used.
The application software can use the “_dioxxh_Get_Irq_Status” function to
distinguish which interrupt is inserted. After an ISR is completed, users must
check if another IRQ is also asserted, then clear current IRQ to allow the
next IRQ coming in.
The two IRQs are named as INT1 and INT2. In PCIDIO 24H/48H/96H, INT1
comes from P1C0, P1C3 or the event counter interrupt. INT2 comes from
P2C0, P2C3 or the timer interrupt. However in PCIDIO 24H, INT2 only comes
from timer interrupt. The sources of INT1 and INT2 is selectable by the
Interrupt Source Control (ISC) Register.
Operation Theorem · 27
4.3.4 Interrupt Source Control
In ISC register (offset 0x20), there are four bits to control the IRQ sources of
INT1 and INT2.
If the application need only one IRQ, you can disable one of the IRQ
sources by software. If your application doesn't need any IRQ source, you
can disable both interrupts. However, the PCI BIOS still assigns an IRQ level
to the PCI card and occupies the PC resource if you only disable the IRQ
sources without changing the initial condition of the PCI controller.
It is not recommended to change the initial condition of the PCI card through
a user's own application software. If users want to disable the IRQ level,
they can use the utility "util DIO 48H.exe" or "util DIO 96H.exe to change
the power on an interrupt setting.
The table 4.3 shows the register format of the ISC (address offset 0x20).
This register is write only. The 4 LSBs are used to control the source of
INT1 and INT2.
INT1
D3 D2 D1 D0 IRQ Sources
IRQ Trigger Condition
Disable
Mode 1
Mode 2
Mode 3
INT2
X
X
X
X
X
X
X
X
0
0
1
1
0
1
0
1
INT1 disable
~P1C0
P1C0 OR ~P1C3 (see following)
Event Counter Counter count down to 0
--
falling edge of P1C0
D3 D2 D1 D0 IRQ Sources
IRQ Trigger Condition
Disable
Mode 1
Mode 2
Mode 3
0
0
1
1
0
1
0
1
X
X
X
X
X
X
X
X
INT2 disable
~P2C0
P2C0 OR ~P2C3 (see following) (*)
Timer Output Timer count down to 0
--
falling edge of P2C0(*)
Table 4.3 ISC register format
(*) Note: Not available on PCIDIO 24H.
Then the IRQ sources is set as “P1C0 OR ~P1C3”, the IRQ trigger
conditions are summarized in table 4.4.
P1/2C0 P1/2C3 IRQ Trigger Condition
High
X
X
Low
PC0=‘H’ disable all IRQ
PC3=‘L’ disable all IRQ
Low
0->1
1->0 PC3 falling edge trigger when PC0=L
High PC0 rising edge trigger when PC3=H
Table 4.4 IRQ Trigger conditions
Because the P1/P2C0 and P1/P2C3 are external signals, the users can
utilize the combination of the four signals to generate a proper IRQ.
28 · Operation Theorem
4.4
12V and 5V Power Supply
The OPTO-22 compatible connectors provide external devices the +12 volts
and +5 volts power supply. To avoid short or overload of the power supply,
resetable fuses are added on all the output power. Refer to Figure 2.5.
The maximum current for 5 volts on every connector is 0.5 A. If the load
current is larger than 0.5 A, the resistance of resetable fuse will increase
because of the rising temperature. The rising resistance will cause the
power supply drop and reduce current. If the overload or short condition is
removed, the fuse will get to normal condition. It is not necessary to repair
or re-install the fuse.
The maximum current of 12 volts for all the four connectors is also 0.5 A.
The action of the fuse is the same as which used for +5V power. The
limitation is more restrictive than 5V power supply because the PCI bus can
not provide large current.
Operation Theorem · 29
5
C/C++ Libraries
This chapter describes the software library for operating these card. Only
the functions in DOS library and Windows 95 DLL are described. Please
refer to the PCI DASK function reference manual, which is included with
the CD, for the descriptions of the Windows 98/NT/2000/XP DLL functions.
The functions of PCIDIO 48H can also be applied to PCIDIO 24H.
Therefore, in the following section, there are no special functions for the
PCIDIO 24H. The software driver of PCIDIO 24H is fully compatible
with that of PCIDIO 48H. In the following sections, each function call that
has a name associated with “DIO48H" can be applied to PCIDIO 24H directly.
The function prototypes and some useful constants are defined in the
header files LIB directory (DOS) and INCLUDE directory (Windows 95). For
Windows 95 DLL, the developing environment can be Visual Basic 4.0 or
above, Visual C/C++ 4.0 or above, Borland C++ 5.0 or above, Borland
Delphi 2.x (32-bit) or above, or any Windows programming language that
allows calls to a DLL. It provides the C/C++, VB, and Delphi include files.
5.1
Libraries Installation
Please refer to the “Software Installation Guide” for the detail information
about how to install the software libraries for DOS, or Windows 95 DLL, or
PCI DASK for Windows 98/NT/2000/XP.
The device drivers and DLL functions of Windows 98/NT/2000/XP are included
with PCI DASK. Please refer the PCI DASK user’s guide and function
reference, which are included in the CyberResearch® CD, for detailed
programming information.
30 · C/C++ Libraries
5.2
Programming Guide
5.2.1 Naming Convention
The functions of the PCIDAQ PCI cards' software driver use full-names to
represent a function's real meaning. The naming convention rules are:
In DOS Environment:
_DIO48H_Initial()
_{hardware_model}_{action_name}. e.g.
.
All functions in the PCIDIO 48H driver are used by the board as
{hardware_model}. But they can be used by PCIDIO 48H and PCIDIO 24H.
In order to recognize the difference between the DOS library and Windows 95
W
library, a capital " " is put on the head of each function name of the
W_DIO48H_Initial()
Windows 95 DLL driver. e.g.
.
5.2.2 Data Types
We defined some data type in DIO48H.h (DOS) and Acl_pci.h (Windows
95). These data types are used by the PCIDAQ Card library. We suggest you
to use these data types in your application programs. The following table
shows the data type names and their range.
Type Name
U8
Description
Range
0 to 255
-32768 to 32767
0 to 65535
8-bit ASCII character
16-bit signed integer
16-bit unsigned integer
32-bit signed integer
32-bit single-precision
floating-point
I16
U16
I32
U32
-2147483648 to 2147483647
0 to 4294967295
F32
32-bit single-precision -3.402823E38 to 3.402823E38
floating-point
F64
64-bit double-precision -1.797683134862315E308 to
floating-point
Boolean logic value
1.797683134862315E309
TRUE, FALSE
Boolean
C/C++ Libraries 31
·
5.3
_DIO48H/96H_Initial
@ Description
The cards are initialized by this function. The software library could be used
to control multiple cards.
@ Syntax
C/C++ (DOS)
U16 _DIO48H_Initial (U16 *existCards, PCI_INFO
*pciInfo)
U16 _DIO96H_Initial (U16 *existCards, PCI_INFO
*pciInfo)
C/C++ (Windows 95)
U16 W_DIO48H_Initial (U16 *existCards, PCI_INFO
*pciInfo)
U16 W_DIO96H_Initial (U16 *existCards, PCI_INFO
*pciInfo)
Visual Basic (Windows 95)
W_DIO48H_Initial (existCards As Integer, pciInfo As
PCI_INFO) As Integer
W_DIO96H_Initial (existCards As Integer, pciInfo As
PCI_INFO) As Integer
@ Argument
existCards: The
numbers
of
installed
PCIDIO
24H/48H/96H cards.
The returned
value shows how many PCIDIO 24H/48H/96H
cards are installed in your system.
It is a structure to record the PCI bus
pciinfo:
plug
information which is decided by p&p
BIOS. The PCI_INFO structure is
defined in ACL_PCI.H The base I/O
address and the interrupt channel
number are stored in pciinfo.
and
play
initiallization
@ Return Code
ERR_NoError
ERR_PCIBiosNotExist
32 · C/C++ Libraries
5.4
Digital Input
@ Description
This function is used to read 8-bit digital input data from digital input ports.
You can get the 8-bit data from _DIO48H_DI by using this function. The written
data and read in data is 8-bit data. Each data is mapped to a signal as the
table below.
D7 D6 D5 D4 D3 D2 D1
D0
PA7 PA6 PA5 PA4 PA3 PA2 PA1 PA0
PB7 PB6 PB5 PB4 PB3 PB2 PB1 PB0
PC7 PC6 PC5 PC4 PC3 PC2 PC1 PC0
@ Syntax
PCIDIO 24H/48H:
C/C++ (DOS)
U16 _DIO48H_DI (U16 cardNo, U16 channelPort, U8
*diData)
U16 _DIO96H_DI (U16 cardNo, U16 channelPort, U8
*diData)
C/C++ (Windows 95)
U16 W_DIO48H_DI (U16 cardNo, U16 channelPort, U16
*diData)
U16 W_DIO96H_DI (U16 cardNo, U16 channelPort, U16
*diData)
Visual Basic (Windows 95)
W_DIO48H_DI (ByVal cardNo As Integer, ByVal
channelPort As Integer, diData As Integer) As
Integer
W_DIO96H_DI (ByVal cardNo As Integer, ByVal
channelPort As Integer, diData As Integer) As
Integer
@ Argument
cardNo:
diData:
card number to select board
return 8-bit value from digital port.
channelPort: port of each channel
C/C++ Libraries 33
·
PCI_CH0_PA: CH1’s Port A
PCI_CH0_PB: CH1’s Port B
PCI_CH0_PC: CH1’s Port C
PCI_CH0_PCU: CH1’s Port C Upper Nibble
PCI_CH0_PCL: CH1’s Port C Low Nibble
PCI_CH1_PA: CH2’s Port A
PCI_CH1_PB: CH2’s Port B
PCI_CH1_PC: CH2’s Port C
PCI_CH1_PCU: CH2’s Port C Upper Nibble
PCI_CH1_PCL: CH2’s Port C Low Nibble
PCI_CH2_PA: CH2’s Port A
PCI_CH2_PB: CH2’s Port B
PCI_CH2_PC: CH2’s Port C
PCI_CH2_PCU: CH2’s Port C Upper Nibble
PCI_CH2_PCL: CH2’s Port C Low Nibble
PCI_CH3_PA: CH3’s Port A
PCI_CH3_PB: CH3’s Port B
PCI_CH3_PC: CH3’s Port C
PCI_CH3_PCU: CH3’s Port C Upper Nibble
PCI_CH3_PCL: CH3’s Port C Low Nibble
PCI_CH0_PAE: CH1’s Port A uses External
Latch
PCI_CH0_PBE: CH1’s Port B uses External
Latch
PCI_CH0_PCE: CH1’s Port C uses External
Latch
PCI_CH1_PAE: CH2’s Port A uses External
Latch
PCI_CH1_PBE: CH2’s Port B uses External
Latch
PCI_CH1_PCE: CH2’s Port C uses External
Latch
Note: 1.CH2 and CH3 are only available for PCIDIO 96H.
2.Only CH0 is available for PCIDIO 24H.
@ Return Code
ERR_NoError
34 · C/C++ Libraries
5.5
Digital Output
@ Description
This function is used to write data to digital output ports.
@ Syntax
C/C++ (DOS)
U16 _DIO48H_DO (U16 cardNo, U16 channelPort, U8
doData)
U16 _DIO96H_DO (U16 cardNo, U16 channelPort, U8
doData)
C/C++ (Windows 95)
U16 W_DIO48H_DO (U16 cardNo, U16 channelPort, U16
doData)
U16 W_DIO96H_DO (U16 cardNo, U16 channelPort, U16
doData)
Visual Basic (Windows 95)
W_DIO48H_DO (ByVal cardNo As Integer, ByVal
channelPort As Integer, ByVal doData As
Integer) As Integer
W_DIO96H_DO (ByVal cardNo As Integer, ByVal
channelPort As Integer, ByVal doData As
Integer) As Integer
@ Argument
cardNo:
channelPort: The same as channelPort in section 5.5.
doData: value will be written to digital output
card number to select board
port
@ Return Code
ERR_NoError
C/C++ Libraries 35
·
5.6
Configuration Port
@ Description
This function is used to configure the Input or Output of each Port. Each I/O
Port of PCIDIO 24H/48H/96H is either input or output, so it has to configure
as input or output before I/O operations are applied.
@ Syntax
C/C++ (DOS)
U16 _DIO48H_Config_Port (U16 cardNo, U16
channelPort, U16 direction);
U16 _DIO96H_Config_Port (U16 cardNo, U16
channelPort, U16 direction)
C/C++ (Windows 95)
U16 W_DIO48H_Config_Port (U16 cardNo, U16
channelPort, U16 direction);
U16 W_DIO96H_Config_Port (U16 cardNo, U16
channelPort, U16 direction)
Visual Basic (Windows 95)
W_DIO48H_Config_Port (ByVal cardNo As Integer, ByVal
channelPort As Integer, ByVal direction As
Integer) As Integer
W_DIO96H_Config_Port (ByVal cardNo As Integer, ByVal
channelPort As Integer, ByVal direction As
Integer) As Integer
@ Argument
cardNo:
card number to select board
The same as channelPort in section 5.5.
port I/O direction
channelPort:
direction:
INPUT_PORT:
OUTPUT_PORT:
the port is configure as INPUT
the port is configure as OUTUT
@ Return Code
ERR_NoError
36 · C/C++ Libraries
5.7
Configuration Channel
@ Description
This function is used to configure the Input or Output of each Channel. Each
I/O Port of PCIDIO 24H/48H/96H is either input or output, so it has to
configure as input or output before I/O operations are applied.
@ Syntax
C/C++ (DOS)
U16 _DIO48H_Config_Channel (U16 cardNo, U16
channelNo, U16 ctrlValue)
U16 _DIO96H_Config_ Channel (U16 cardNo, U16
channelNo, U16 ctrlValue)
C/C++ (Windows 95)
U16 W_DIO48H_Config_Channel (U16 cardNo, U16
channelNo, U16 ctrlValue)
U16 W_DIO96H_Config_ Channel (U16 cardNo, U16
channelNo, U16 ctrlValue)
Visual Basic (Windows 95)
W_DIO48H_Config_Channel (ByVal cardNo As Integer,
ByVal channelNo As Integer, ByVal ctrlValue
As Integer) As Integer
W_DIO96H_Config_ Channel (ByVal cardNo As Integer,
ByVal channelNo As Integer, ByVal ctrlValue
As Integer) As Integer
@ Argument
cardNo:
card number to select board
channelNo: PCI_CH0, PCI_CH1, PCI_CH2, or PCI_CH3
ctrlValue: the control value to set up PA, PB, and PC
as input or output port.
C/C++ Libraries 37
·
ctrlValue Port A Port CU Port B Port CL
PORT_OOOO OUT
PORT_OOOI OUT
PORT_OOIO OUT
PORT_OOII OUT
PORT_OIOO OUT
PORT_OIOI OUT
PORT_OIIO OUT
PORT_OIII OUT
PORT_IOOO IN
PORT_IOOI IN
PORT_IOIO IN
PORT_IOII IN
PORT_IIOO IN
PORT_IIOI IN
PORT_IIIO IN
PORT_IIII IN
OUT
OUT
OUT
OUT
IN
IN
IN
IN
OUT
OUT
OUT
OUT
IN
IN
IN
IN
OUT
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
IN
OUT
OUT
IN
IN
OUT
OUT
IN
IN
OUT
OUT
IN
IN
The ctrlValue constants are defined in acl_pci.h and acl_pci.bas.
@ Return Code
ERR_NoError
38 · C/C++ Libraries
5.8
Set Interrupt Control
@ Description
This function is used to set the interrupt configuration. The interrupt
should be configured before the function starts.
@ Syntax
C/C++ (DOS)
void _DIO48H_Set_INT_Control(U16 cardNo, U16
ctrlValue);
void _DIO96H_Set_INT_Control(U16 cardNo, U16
ctrlValue);
C/C++ (Windows 95)
void W_DIO48H_Set_INT_Control(U16 cardNo, U16
ctrlValue);
void W_DIO96H_Set_INT_Control(U16 cardNo, U16
ctrlValue);
Visual Basic (Windows 95)
W_DIO48H_Set_INT_Control (ByVal cardNo As Integer,
ByVal ctrlValue As Integer)
W_DIO96H_Set_INT_Control (ByVal cardNo As Integer,
ByVal ctrlValue As Integer)
@ Argument
cardNo:
card number to select board
ctrlValue: the valid values of configuring the
interrupt
are
INT1:
0x00 à disable
0x01 à mode1
0x02 à mode2
0x03 à mode3
INT2:
0x00 à disable
0x04 à mode1
0x08 à mode2
0x0c à mode3
Please refer to the section 4.3.4 for detailed description.
C/C++ Libraries 39
·
5.9
Timer Start
@ Description
This function is used to set and start the timer0 of the on-board timer
8254.
@ Syntax
C/C++ (DOS)
void _DIO48H_Timer_Start(U16 cardNo, U16 timer0Mode,
U16 c0)
void _DIO96H_Timer_Start(U16 cardNo, U16 timer0Mode,
U16 c0)
C/C++ (Windows 95)
void W_DIO48H_Timer_Start(U16 cardNo, U16 timer0Mode,
U16 c0)
void W_DIO96H_Timer_Start(U16 cardNo, U16 timer0Mode,
U16 c0)
Visual Basic (Windows 95)
W_DIO48H_Timer_Start(ByVal cardNo As Integer, ByVal
timer0Mode As Integer, ByVal c0 As Integer)
W_DIO96H_Timer_Start(ByVal cardNo As Integer, ByVal
timer0Mode As Integer, ByVal c0 As Integer);
@ Argument
cardNo:
card number to select board
timer0Mode: the six modes of 8254, please refer to
section 4.2.2 for detailed description
c0:
the counter/timer value of time0.
40 · C/C++ Libraries
5.10 Timer Read
@ Description
This function is used to read the current count of the timer0 of the on-
board timer 8254 .
@ Syntax
PCIDIO 24H/48H:
C/C++ (DOS)
void _DIO48H_Timer_Read(U16 cardNo, U16
*counterValue);
void _DIO96H_Timer_Read(U16 cardNo, U16
*counterValue);
C/C++ (Windows 95)
void W_DIO48H_Timer_Read(U16 cardNo, U16
*counterValue);
void W_DIO96H_Timer_Read(U16 cardNo, U16
*counterValue);
Visual Basic (Windows 95)
W_DIO48H_Timer_Read(ByVal cardNo As Integer,
counterValue As Integer);
W_DIO96H_Timer_Read (ByVal cardNo As Integer,
counterValue As Integer);
@ Argument
cardNo:
counterValue:
card number to select board
the value of the current count
C/C++ Libraries 41
·
5.11 Timer Stop
@ Description
This function is used to stop the timer0 of the on-board timer 8254 .
@ Syntax
C/C++ (DOS)
void _DIO48H_Timer_Stop(U16 cardNo, U16
*counterValue);
void _DIO96H_Timer_Stop(U16 cardNo, U16
*counterValue);
C/C++ (Windows 95)
void W_DIO48H_Timer_Stop(U16 cardNo, U16
*counterValue);
void W_DIO96H_Timer_Stop(U16 cardNo, U16
*counterValue);
Visual Basic (Windows 95)
W_DIO48H_Timer_Stop (ByVal cardNo As Integer,
counterValue As Integer);
W_DIO96H_Timer_Stop (ByVal cardNo As Integer,
counterValue As Integer);
@ Argument
cardNo:
card number to select board
counterValue:
the value of current count when the
counter is stopped
42 · C/C++ Libraries
5.12 Cascaded Timer
@ Description
This function is used to set and start the cascaded timer1 and timer 2 of
the on- board timer 8254 .
@ Syntax
C/C++ (DOS)
void _DIO48H_Cascaded_Timer(U16 cardNo, U16 c1, U16
c2);
void _DIO96H_Cascaded_Timer(U16 cardNo, U16 c1, U16
c2);
C/C++ (Windows 95)
void W_DIO48H_Cascaded_Timer(U16 cardNo, U16 c1, U16
c2);
void W_DIO96H_Cascaded_Timer(U16 cardNo, U16 c1, U16
c2);
Visual Basic (Windows 95)
W_DIO48H_Cascaded_Timer (ByVal cardNo As Integer,
ByVal c1 As Integer, ByVal c2 As Integer)
W_DIO96H_Cascaded_Timer (ByVal cardNo As Integer,
ByVal c1 As Integer, ByVal c2 As Integer)
@ Argument
cardNo:
card number to select board
c1:
c2:
the value of divisor used in timer 1
the value of divisor used in timer 2
C/C++ Libraries 43
·
5.13 Get IRQ Status
@ Description
This function is used to read back the status of interrupt when interrupt
is inserted.
@ Syntax
C/C++ (DOS)
void _DIO48H_Get_IRQ_Status(U16 cardNo, U16
*int1Status, U16 *int2Status);
void _DIO96H_Get_IRQ_Status(U16 cardNo, U16
*int1Status, U16 *int2Status);
C/C++ (Windows 95)
void W_DIO48H_Get_IRQ_Status(U16 cardNo, U16
*int1Status, U16 *int2Status);
void W_DIO96H_Get_IRQ_Status(U16 cardNo, U16
*int1Status, U16 *int2Status);
Visual Basic (Windows 95)
W_DIO48H_Get_IRQ_Status (ByVal cardNo As Integer,
int1Status As Integer, int2Status As Integer);
W_DIO96H_Get_IRQ_Status (ByVal cardNo As Integer,
int1Status As Integer, int2Status As Integer);
@ Argument
cardNo:
int1Status: the status of INT1,
int1Status = 0 à no interrupt
int1Status = 1 à interrupt 1 inserted
int2Status: the status of INT2
card number to select board
int2Status = 0 à no interrupt
int2Status = 1 à interrupt 2 inserted
Please refer to section 4.3 for detailed description.
44 · C/C++ Libraries
5.14 Clear IRQ
@ Description
This function is used to clear the interrupt generated from the 48H/96H
series.
@ Syntax
C/C++ (DOS)
void _DIO48H_CLR_IRQ(U16 cardNo);
void _DIO96H_CLR_IRQ(U16 cardNo);
C/C++ (Windows 95)
void W_DIO48H_CLR_IRQ(U16 cardNo);
void W_DIO96H_CLR_IRQ(U16 cardNo);
Visual Basic (Windows 95)
W_DIO48H_CLR_IRQ (ByVal cardNo As Integer);
W_DIO96H_CLR_IRQ (ByVal cardNo As Integer);
@ Argument
cardNo:
card number to select board
5.15 Software Reset
@ Description
This function is used to reset the I/O port configuration. After reseting the
24H/48H/96H, all the ports will be set as input ports. Note that this
function can not re-start the PCI bus and all the hardware setting won‘t be
change either.
@ Syntax
PCIDIO 24H/48H:
C/C++ (DOS)
U16 _DIO48H_Software_Reset (U16 cardNo)
U16 _DIO96H_Software_Reset (U16 cardNo)
C/C++ (Windows 95)
U16 W_DIO48H_Software_Reset (U16 cardNo)
U16 W_DIO96H_Software_Reset (U16 cardNo)
C/C++ Libraries 45
·
Visual Basic (Windows 95)
W_DIO48H_Software_Reset (ByVal cardNo As Integer) As
Integer
Integer
W_DIO96H_Software_Reset (ByVal cardNo As Integer) As
Integer
@ Argument
cardNo: card number which the DIO will be reset.
@ Return Code
ERR_NoError
5.16 Interrupt Start under Windows
@ Description
This function is only available with the Windows 95/98 driver. It is
used to initialize and start up the interrupt control. Please refer to section
4.3 for a detailed description of interrupt system. After calling this function,
every time an interrupt request signal generated, a software event is
signaled. So that in your program, you can use wait operation to wait for the
event. When the event is signaled, it means an interrupt is generated.
Please refer to the sample program DIO48Hint.c or DIO96Hint.c.
@ Syntax
C/C++ (Windows 95)
void W_DIO48H_INT_Start (U16 cardNo, U16 c1, U16 c2,
U16 ctrlValue, HANDLE *hIntEvent)
void W_DIO48H_INT_Start (U16 cardNo, U16 c1, U16 c2,
U16 ctrlValue, HANDLE *hIntEvent)
Visual Basic (Windows 95)
W_DIO48H_INT_Start (ByVal cardNo As Integer, ByVal c1
As Integer, ByVal c2 As Integer, ByVal
ctrlValue As Integer, hIntEvent As Long)
W_DIO96H_INT_Start (ByVal cardNo As Integer, ByVal c1
As Integer, ByVal c2 As Integer, ByVal
ctrlValue As Integer, hIntEvent As Long)
46 · C/C++ Libraries
@ Argument
cardNo: card number which the DIO will be reset.
c1: If the interrupt source is set as internal
timer source, this value is the frequency
divider of Timer#1.
c2: If the interrupt source is set as internal
timer source, this value is the frequency
divider of Timer#2.
ctrlValue:the value for INT mode setting. The
value can be set for INT1 is INT1_OFF,
INT1_P1C0, INT1_P1C3C0, or INT1_EVENT_IRQ.
The value can be set for INT2 is INT2_OFF,
INT2_P2C0, INT2_P2C3C0, or INT2_TIMER_IRQ.
Please refer to section 3.3.4 for detailed
description.
hIntEvent:the handle of the event for interrupt
signals.
@ Return Code
ERR_NoError
5.17 Interrupt Stop under Windows
@ Description
This function is only available in the Windows 95/98 driver. It is
used to disable the interrupt signal generation.
@ Syntax
C/C++ (Windows 95)
void W_DIO48H_INT_Stop (U16 cardNo)
void W_DIO96H_INT_Stop (U16 cardNo)
Visual Basic (Windows 95)
W_DIO48H_INT_Stop (ByVal cardNo As Integer)
W_DIO96H_INT_Stop (ByVal cardNo As Integer)
@ Argument
cardNo: card number which the DIO will be reset.
@ Return Code
ERR_NoError
C/C++ Libraries 47
·
Product Service
Diagnosis and Debug
CyberResearch, Inc. maintains technical support lines staffed by experienced
Applications Engineers and Technicians. There is no charge to call and we will
return your call promptly if it is received while our lines are busy. Most problems
encountered with data acquisition products can be solved over the phone. Signal
connections and programming are the two most common sources of difficulty.
CyberResearch support personnel can help you solve these problems, especially if
you are prepared for the call.
To ensure your call’s overall success and expediency:
1) Have the phone close to the PC so you can conveniently and quickly take action
that the Applications Engineer might suggest.
2) Be prepared to open your PC, remove boards, report back-switch or jumper
settings, and possibly change settings before reinstalling the modules.
3) Have a volt meter handy to take measurements of the signals you are trying to
measure as well as the signals on the board, module, or power supply.
4) Isolate problem areas that are not working as you expected.
5) Have the source code to the program you are having trouble with available so
that preceding and prerequisite modes can be referenced and discussed.
6) Have the manual at hand. Also have the product’s utility disks and any other
relevant disks nearby so programs and version numbers can be checked.
Preparation will facilitate the diagnosis procedure, save you time, and avoid repeated
calls. Here are a few preliminary actions you can take before you call which may
solve some of the more common problems:
1) Check the PC-bus power and any power supply signals.
2) Check the voltage level of the signal between SIGNAL HIGH and SIGNAL LOW,
or SIGNAL+ and SIGNAL– . It CANNOT exceed the full scale range of the board.
3) Check the other boards in your PC or modules on the network for address and
interrupt conflicts.
4) Refer to the example programs as a baseline for comparing code.
Product Service • 48
Warranty Notice
CyberResearch, Inc. warrants that this equipment as furnished will be free from
defects in material and workmanship for a period of one year from the confirmed
date of purchase by the original buyer and that upon written notice of any such
defect, CyberResearch, Inc. will, at its option, repair or replace the defective item
under the terms of this warranty, subject to the provisions and specific exclusions
listed herein.
This warranty shall not apply to equipment that has been previously repaired or
altered outside our plant in any way which may, in the judgment of the manufacturer,
affect its reliability. Nor will it apply if the equipment has been used in a manner
exceeding or inconsistent with its specifications or if the serial number has been
removed.
CyberResearch, Inc. does not assume any liability for consequential damages
as a result from our products uses, and in any event our liability shall not exceed
the original selling price of the equipment.
The equipment warranty shall constitute the sole and exclusive remedy of any Buyer
of Seller equipment and the sole and exclusive liability of the Seller, its successors
or assigns, in connection with equipment purchased and in lieu of all other war-
ranties expressed implied or statutory, including, but not limited to, any implied
warranty of merchant ability or fitness and all other obligations or liabilities of seller,
its successors or assigns.
The equipment must be returned postage prepaid. Package it securely and insure it.
You will be charged for parts and labor if the warranty period has expired.
Returns and RMAs
If a CyberResearch product has been diagnosed as being non-functional, is visibly
damaged, or must be returned for any other reason, please call for an assigned
RMA number. The RMA number is a key piece of information that lets us track and
process returned merchandise with the fastest possible turnaround time.
PLEASE CALL FOR AN RMA NUMBER!
Packages returned without an RMA number will be refused!
In most cases, a returned package will be refused at the receiving dock if its
contents are not known. The RMA number allows us to reference the history of
returned products and determine if they are meeting your application’s require-
ments. When you call customer service for your RMA number, you will be asked to
provide information about the product you are returning, your address, and
a contact person at your organization.
Please make sure that the RMA number is
prominently displayed on the outside of the box.
• Thank You •
Warranty • 49
|