Install the Rechargeable Battery
Pack into the Handset
Follow these steps before using your cordless handset:
• Make sure the handset is registered to main base unit.
• Fully charge the battery pack.
Press down on the handset battery
1
case cover (use the finger indention
for a better grip) and slide the cover
downward to remove.
Plug the battery pack connector (red
2
& black wires) into the jack inside the
battery compartment. (The connector
notches fit into the grooves of the
jack only one-way.) Match the wire
colors to the polarity label in the
battery compartment, and push the
connector in until you hear a click.
Make sure you have a good connection
3
by slightly pulling on the battery wires.
If the connection is secure, the battery
jack will remain in place.
Place the battery case cover back on
the handset by sliding it upwards
until it clicks into place.
4
Place the handset in the charging
cradle with the keypad facing forward.
5
• Use only the Uniden battery (BT-446)
supplied with your phone.
Replacement batteries are also available
through the Uniden Parts Department.
(See page 2.)
• Recharge your handset on a regular
basis by returning the handset to the
charger after each phone call.
Rechargeable Nickel-Metal-Hydride Batteries
Must Be Recycled or Disposed of Properly
– 3 –
Battery Information
Low battery alert
When the batteries are very low and need to be charged, the phone is
programmed to eliminate functions in order to save power.
The batteries need to be charged when:
- The empty battery icon
appears.
- Low Battery appears in the display.
If the phone is in standby mode, none of the keys will operate.
If you are on a call, complete your conversation as quickly as possible,
and return the handset to the charging cradle.
Cleaning the battery charging contacts
To maintain a good charge, it is
important to clean the charging
contacts on both the handset and
the charger once a month. Using
water only, dampen a cloth to clean
the charging contacts. Then make
sure to go back over the charging
contacts with a dry cloth before
returning the handset to the
charger to charge.
Caution: Do not use paint thinner, benzene, alcohol, or other chemical
products. Doing so may discolor the surface of the telephone and
damage the finish.
Connect the Charger
Connect the AC adapter to the DC
1
IN 9V jack and to a standard 120V
AC wall outlet.
Set the charger on a desk or
2
tabletop, and place the handset in
the charger with the keypad
facing forward.
– 4 –
Make sure the charge LED illuminates. If the LED does not
illuminate, check to see that the AC adapter is plugged in and that
the handset makes good contact with the charger charging contacts.
3
• Use only the supplied AD-310 AC adapter. Do not use
any other AC adapter.
• Place the charger close to the AC outlet so that you can
unplug the AC adapter easily.
Register the Handset
YOU NEED TO REGISTER THE DCX640 TO THE MAIN BASE BEFORE USE!
Before registering the handset,
1
1
the battery pack must be charged
DCX640
Charge the handset
Handset
for 15-20 hours.
for 15-20 hours.
Place the extra handset
2
Charger
in the main base unit to
begin registration. (Picture is the
DCX640
Handset
2
DCT646 series main base.)
While the handset is registering,
Handset Registeringwill
appear in the LCD. When
Place the DCX640
handset in the main
base to register.
3
Main Base
Registration Complete
is displayed, the handset has
been registered to the base.
If Registration Failed
appears, please try these
ꢀꢀꢀꢀ*CPFUGV
ꢀꢀ4GIKUVGTKPI
ꢀꢀ4GIKUVTCVKQP
ꢀꢀꢀ%QORNGVG
DCX640 Handset
+
3
Main Base
steps again.
• The handset can be registered when the main base is in
standby mode.
• Standby Mode - The handset is not in use and talk/flash
has not been pressed.
Using the DCX640 with the
Integrated Answering Device
If the original unit has a built-in answering system, you can check
your new messages, skip, repeat, or delete your messages with the
DCX640 handset. For more detailed instructions, see the owner’s
manual supplied with the original unit.
– 5 –
1) Press select/ on the handset in standby mode.
ꢀ
2) After the announcement, enter a command in the following list within
30 seconds.
3) To quit, hang up or press end.
Command
Function
Command
Function
1
2
3
4
5
Repeat a Message
6
7
8
9
0
Answering System On
Memo Record/Stop
Greeting Message Record/Stop
Answer System Off
Playing incoming Messages
Skipping a Message
Deleting a Message
Stop Operation
Help Guidance
• If you press end before the answering system answers, the phone
will return to standby mode.
• When the answering system does not answer within 6 seconds, you
will hear a beep and the phone will return to standby mode.
• When you receive a call, remote operation is canceled.
I.C. Notice
TERMINAL EQUIPMENT
NOTICE: This equipment meets the applicable Industry Canada Terminal Equipment Technical
Specifications. This is confirmed by the registration number. The abbreviation, IC, before the
registration number signifies that registration was performed based on a Declaration of
Conformity indicating that Industry Canada technical specifications were met. It does not
imply that Industry Canada approved the equipment.
NOTICE: The Ringer Equivalence Number (REN) for this terminal equipment is marked on the
equipment itself. The REN assigned to each terminal equipment provides an indication of the
maximum number of terminals allowed to be connected to a telephone interface. The
termination on an interface may consist of any combination of devices subject only to the
requirement that the sum of the Ringer Equivalence Numbers of all the devices does not
exceed five.
RADIO EQUIPMENT
The term “IC:” before the radio certification number only signifies that Industry Canada
technical specifications were met.
Operation is subject to the following two conditions: (1) this device may not cause
interference, and (2) this device must accept any interference, including interference that
may cause undesired operation of the device. “Privacy of communications may not be ensured
when using this telephone.”
THE FCC WANTS YOU TO KNOW
Changes or modifications to this product not expressly approved by Uniden, or operation of
this product in any way other than as detailed by the owner's manual, could void your
authority to operate this product.
Uniden works to reduce lead content in our PVC coated cords in our products and accessories.
Warning!
The cords on this product and/or accessories contain lead, a chemical known to the State of
California to cause birth defects or other reproductive harm. Wash hands after handling.
– 6 –
One Year Limited Warranty
Important: Evidence of original purchase is required for warranty service.
WARRANTOR: UNIDEN AMERICA CORPORATION (“Uniden”)
ELEMENTS OF WARRANTY: Uniden warrants, for one year, to the original retail owner, this Uniden Product to
be free from defects in materials and craftsmanship with only the limitations or exclusions set out below.
WARRANTY DURATION: This warranty to the original user shall terminate and be of no further effect 12
months after the date of original retail sale. The warranty is invalid if the Product is (A) damaged or not
maintained as reasonable or necessary, (B) modified, altered, or used as part of any conversion kits,
subassemblies, or any configurations not sold by Uniden, (C) improperly installed, (D) serviced or
repaired by someone other than an authorized Uniden service center for a defect or malfunction covered
by this warranty, (E) used in any conjunction with equipment or parts or as part of any system not
manufactured by Uniden, or (F) installed or programmed by anyone other than as detailed by the owner’s
manual for this product.
STATEMENT OF REMEDY: In the event that the product does not conform to this warranty at any time while
this warranty is in effect, warrantor will either repair or replace the defective unit and return it to you
without charge for parts, service, or any other cost (except shipping and handling) incurred by warrantor or
its representatives in connection with the performance of this warranty. Warrantor may replace the unit
with a new or refurbished unit. THE LIMITED WARRANTY SET FORTH ABOVE IS THE SOLE AND ENTIRE
WARRANTY PERTAINING TO THE PRODUCT AND IS IN LIEU OF AND EXCLUDES ALL OTHER WARRANTIES OF ANY
NATURE WHATSOEVER, WHETHER EXPRESSED, IMPLIED OR ARISING BY OPERATION OF LAW, INCLUDING, BUT
NOT LIMITED TO ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
THIS WARRANTY DOES NOT COVER OR PROVIDE FOR THE REIMBURSEMENT OR PAYMENT OF INCIDENTAL OR
CONSEQUENTIAL DAMAGES. Some states do not allow this exclusion or limitation of incidental or
consequential damages so the above limitation or exclusion may not apply to you.
LEGAL REMEDIES: This warranty gives you specific legal rights, and you may also have
other rights which vary from state to state. This warranty is void outside the United States of America
and Canada.
PROCEDURE FOR OBTAINING PERFORMANCE OF WARRANTY: If, after following the instructions in the
owner’s manual you are certain that the Product is defective, pack the Product carefully (preferably in its
original packaging). The Product should include all parts and accessories originally packaged with the
Product. Include evidence of original purchase and a note describing the defect that has caused you to
return it. The Product should be shipped freight prepaid, by traceable means, to warrantor at:
Uniden America Corporation
Parts and Service Division
4700 Amon Carter Blvd.
Fort Worth, TX 76155
(800) 297-1023, 8 a.m. to 5 p.m. Central, Monday through Friday
May be covered under one or more of the following U.S. patents:
4,523,058 4,595,795 4,797,916 5,381,460 5,426,690 5,434,905
5,491,745 5,493,605 5,533,010 5,574,727 5,581,598 5,650,790
5,660,269 5,661,780 5,663,981 5,671,248 5,696,471 5,717,312
5,732,355 5,754,407 5,758,289 5,768,345 5,787,356 5,794,152
5,801,466 5,825,161 5,864,619 5,893,034 5,912,968 5,915,227
5,929,598 5,930,720 5,960,358 5,987,330 6,044,281 6,070,082
6,125,277 6,253,088 6,314,278 6,418,209
– 7 –
|