Computer Tech Link CTL 5xn User Manual

COLOR MONITOR  
Model No : CTL 5xn  
FEDERAL COMMUNICATIONS COMMISSION RADIO  
FREQUENCY INTERFERENCE STATEMENT  
NOTE: This equipment has been tested and found to comply with the  
limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.  
These limits in a residential installation. This equipment generates, uses  
and can radiate radio frequency energy and, if not installed and used in  
accordance with the instructions, may cause harmful interference to  
radio communications. However, there is no guarantee that interference  
will not occur in a particular installation. If this equipment does cause  
harmful interference to radio or television reception, which can be  
determined by turning the equipment off and on, the user is  
encouraged to try to correct the interference by one or more of the  
following measures :  
ƒ¡Reorient or relocate the receiving antenna.  
ƒ¡Increase the separation between the equipment and receiver.  
ƒ¡Connect the equipment to an outlet on a circuit different from that to  
which the receiver is connected.  
ƒ¡Consult the dealer or an experienced radio, TV technician for help.  
CAUTION: Any changes or modifications not expressly approved by the  
part responsible for compliance could void the user's authority  
to operate the equipment.  
CANADIAN DEPARTMENT OF COMMUNICATIONS  
COMPLIANCE STATEMENT  
This digital apparatus does not exceed the Class A/ Class B (whichever  
is applicable) limits for radio noise emissions from digital apparatus set  
out in the Radio Interference Regulations of the Canadian Department of  
Communications.  
Avis de conformité aux normes du Ministère des Communications du  
Canada.  
Le present appareil numérique n¡emet pas de bruits radioélectriques  
depassant les limites applicables aux appareils numériques de Class  
A/ de Class B (selon le cas) prescrites dans le règlement sur le brouillage  
radioélectrique édicte par le ministère des communications du canada.  
The power cord is used as a main disconnect device. Disconnect the power  
cord before servicing.  
The outlet must be installed near the monitor and must be easily accessible.  
As an ENERGY STAR Partner, Daewoo Electronics Co., Ltd. has determined that  
this product meets the Energy Star guidelines for energy efficiency.  
CONTENTS  
Introduction  
1
2
Product Features  
Setup  
Installing the Tilt/ Swivel Stand  
3
3
Connecting the D-Sub Signal Cable  
Connecting to Your Macintosh Computer  
Connecting the Power Cord  
Power Management System  
DDC for Plug & Play  
4
4
4
5
5
Operation & Adjustment  
Specifications  
6
9
Factory Preset Timings  
10  
11  
Troubleshooting  
Appendix  
Description for D-sub Connector  
INTRODUCTION  
This manual explains how to correctly install, operate and get the  
best performance from your monitor. Please read this user's  
manual carefully before installing your monitor, then keep it near  
your monitor for quick reference.  
First, please check that the contents of the carton box corresponds  
with the following checklist :  
¡ Color monitor  
¡ Power cord  
¡ Tilt/ swivel stand  
¡ User's manual  
¡ Warranty Handbook  
¡ Warranty Registration Card  
If there is any item missing or damaged, please contact your  
dealer. Please keep the carton box and packing materials so that  
you may properly store or transport your monitor.  
1
PRODUCT FEATURES  
¡ The convenient and user-friendlly on-screen display allows for  
easy and accurate adjustments of horizontal and vertical screen  
size and position, geometry and screen color.  
¡ The monitor supports a safe working environment in strict  
compliance with the MPR¥–standard for low emissions.  
¡ The monitor complies with the VESA Display Data Channel  
(DDC) specification for “Plug & Play” compatibility. Advanced  
m icrocircu itry m akes set-u p and configu ration fast and  
effortless.  
¡ The monitor features Advanced Color Controls for fine-tuning  
to meet your own personal tastes or application requirements.  
Use the on-screen controls to adjust the color temperature, RB  
gain value for the best possible screen color and intensity.  
¡ Just activate the higher refresh rates of the monitor to stabilize  
the screen and eliminate the annoying flicker that contributes to  
eye-strain and headaches.  
¡ The “borderless” full-screen display capability works under all  
grap hic m od es and p rovid es a larger view ing area than  
conventional monitors, giving you a better picture with more  
workspace.  
2
SETUP  
INSTALLING THE TILT/SWIVEL STAND  
1. Ensure that the power to the monitor is off.  
2. Set the monitor face down with the underside facing you.  
Please be careful so as not to scratch the monitor screen.  
3. Align the four hooks on the stand with the guide holes of  
bottom chassis of the monitor.  
4. Insert the hooks into the guide holes.  
5. Slide the tilt/ swivel stand toward the front of the monitor until  
the latch locks in position.  
6. Turn the monitor and the stand upright.  
2
PUSH  
1
PUSH  
F R O N T  
<Removing the tilt/swivel stand>  
If you want to remove the tilt/ swivel stand on the monitor, press  
the latch and pull the tilt/ swivel stand toward the back of the  
monitor. Lift the stand to separate.  
3
CONNECTING THE D-SUB SIGNAL CABLE  
1. Turn off the computer and monitor.  
2. Connect the 15 pin D-sub connector to the output port of the  
video card in your computer.  
3. Tighten the screws of connector.  
CONNECTING TO YOUR MACINTOSH COMPUTER  
1. Turn off the computer and monitor.  
2. Attach the Macintosh cable adapter to the Macintosh video  
card.  
3. Tighten the screws on the cable adapter.  
4. Connect the signal cable provided with your monitor to the  
other end of the Macintosh cable adapter.  
5. Tighten the screws between the Macintosh cable adapter and  
the signal cable.  
CONNECTING THE POWER CORD  
1. Plug the power cord into the AC receptacle located at the back  
of the monitor.  
2. Plug the other end of the power cord into the AC outlet.  
If your power cord is PC to Monitor type, plug the other end of the  
power cord into the AC receptacle in the computer.  
4
POWER MANAGEMENT SYSTEM  
If you use the monitor with a computer which complies with the  
power saving program, you can set the monitor to go blank when  
the system has remained unused for a period of time. To specify  
the period or to disable this feature, set the system timeout field  
of the computer's system setup program or use special software  
for power saving. See the computer user's manual for the details  
of using the system setup. While the monitor is in power saving  
m od e (blank screen), it consu m es less p ow er than norm al  
state;the color of the power LED will indicate the state. To restore  
the screen image, press any key of your keyboard or move your  
mouse. If the signal cable is connected loosely or disconnected,  
the power saving feature will operate.  
DISPLAY DATA CHANNEL (DDC) FOR PLUG & PLAY  
If you use the monitor with a computer which complies with  
DDC1/ 2B of VESA, the Host-Video Card automatically  
configures itself without your intervention in a way that best fits  
the attached monitor.  
The Display Data Channel, DDC, allows the monitor to inform  
the host system about configuration information for optimum  
use of the monitor . Use of the Video Card utility is not required  
to match the resolutions and refresh rates of the monitor and  
video card.  
5
OPERATION & ADJUSTMENT  
+
EXIT  
ADJUST  
SELECT  
MENU  
: Launch OSD(On-Screen Display) Menus  
: Select the next function  
MENU  
: Select the previous function  
: Increase the value of any selected function  
: Decrease the value of any selected function  
+
EXIT  
: Exit OSD Menus & Launch OSD Menus, when no OSD  
Key Process  
MENU  
1024X768  
60Hz  
1024X768  
60Hz  
CONTRAST  
BRIGHTNESS  
H.POSITION  
H.SIZE  
CONTRAST  
BRIGHTNESS  
H.POSITION  
H.SIZE  
V.POSITION  
V.SIZE  
V.POSITION  
V.SIZE  
50  
50  
+
+
Register Value change  
Register Value change  
MENU  
MENU  
1024X768  
60Hz  
1024X768  
60Hz  
PINCUSHION  
PINCUSHION  
TRAPEZOID  
COLOR TEMP.  
R. GAIN  
TRAPEZOID  
COLOR TEMP.  
R. GAIN  
B. GAIN  
B. GAIN  
DEGAUSSING  
RECALL  
DEGAUSSING  
RECALL  
50  
USER 9300 6550
+
+
Color Select  
Register Value change  
EXIT  
OSD OFF  
6
1 . OSD(On -Screen Display) Men u 1  
Adjust the contrast of image, the  
CONTRAST  
difference between light and dark areas  
on the screen.  
50  
50  
Adjust the brightness of the entire  
display.  
BRIGHTNESS  
Adjust the position of the display horizontally  
(left or right).  
H. POSITION  
50  
Adjust the display width (horizontal size).  
H. SIZE  
V. POSITION  
V. SIZE  
50  
50  
50  
Adjust the position of the display vertically  
(up or down).  
Adjust the display height (vertical size).  
7
2 . OSD (On -Screen Display) Men u 2  
Adjust the left and right margins for more  
convex or more concave margins.  
PINCUSHION  
+
ƒUImage turns to  
ƒUImage turns to  
by  
by  
.
.
50  
50  
Adjust the trapezoid of the screen by moving  
the lines inward or outward.  
TRAPEZOID  
+
ƒUImage turns to  
ƒUImage turns to  
by  
by  
.
.
Choose different preset color temperatures or  
set your own customized color parameters.  
COLOR TEMP.  
USER  
9300  
6550  
Adjust the red gain.  
R. GAIN  
50  
50  
Adjust the blue gain.  
B. GAIN  
Degauss the display and restore image quality  
DEGAUSSING  
NO YES  
Reset the screen to the Factory Preset Display  
settings.  
RECALL  
YES  
NO  
8
SPECIFICATIONS  
Picture Tube  
Type :15-inch, Flat Square Tube type  
(14-inch, viewing area)  
Dot Pitch : 0.28mm, MPR ¥–  
Face Treatment: Non-glare/ Anti-static  
Video  
Input Signal : R.G.B Analog  
Amp. Bandwidth : 60 MHz  
Input Sync : TTL, separate negative/ positive  
Scan Frequency  
Horizontal : 30 - 54 KHz  
Vertical : 50 - 120 Hz  
Max. Resolution  
Power Source  
Display Area  
1024 dots¡¿768 lines. (at 60 Hz)  
Free Voltage (100-240 Vac, 50/ 60Hz )  
Standard Display Area :  
264mm(H)¡¿198mm(V)  
Full Screen Size :284mm(H)¡¿212mm(V)  
Power Consumption Max. 80W  
State  
Recovery Time Power LED  
On  
None  
Green  
Stand-by  
Suspend  
Green:0.5second  
Amber:0.5second  
3 seconds  
Sleep  
Off  
-
-
Amber  
Off  
Regulatory Approvals  
Safety  
EMI  
: UL, CSA, DHHS  
: FCC-B  
9
Tilt /Swivel Range Tilt : 5¡£forward, 10¡£backward  
Swivel : ¡ 45¡£leftward, rightward  
Dimension  
368(W)¡¿394(D)¡¿382(H)mm  
(set with stand)  
Weight (net/Gross) 27.6/ 31.4 lbs  
12.5/ 14.2Kg  
Operating Environment  
Temperature : 10~4˚C/ 50~104˚F  
Relative Humidity : 8~80%  
Storage Environment  
Temperature : -20~45˚C/ -68~113˚F  
Relative Humidity : 5~90%  
FACTORY PRESET TIMINGS  
Resolution  
Mode  
VGA  
H.Freq (KHz)  
V. Freq (Hz)  
Remark  
(dots¡¿lines)  
720¡¿400  
640¡¿480  
640¡¿480  
800¡¿600  
1024¡¿768  
800¡¿600  
31.5  
31.5  
37.5  
46.9  
48.4  
53.7  
70  
60  
75  
75  
60  
85  
Non-interlaced  
Non-interlaced  
Non-interlaced  
Non-interlaced  
Non-interlaced  
Non-interlaced  
VGA  
VESA VGA 75  
VESA 46K  
VESA 1024/ 60  
VESA 800x600 @85Hz  
This monitor has stored above-mentioned six timings in factory. You  
can save up to 10 modes in the user memory automatically. Please note  
that if you save to user memory over ten times, the first mode saved  
will be replaced with your eleventh mode.  
10  
TROUBLESHOOTING  
Symptom  
Check  
No picture.  
Check if POWER SWITCH and COMPUTER  
POWER SWITCH are in the on position.  
‹q  
Check if the signal cable is correctly connected to  
the video card.  
‹q  
Check if the pins of D-sub connector are not bent.  
‹q  
Check if the computer is in the power saving mode.  
POWER LED is not lit. Check if POWER SWITCH is in the on position.  
‹q  
Check if the power cord is correctly connected.  
Image is unstable.  
Check if the signal cable is suitable to the video card.  
Image is not centered,  
too small, or too large.  
Adjust H&V SIZE or H&V POSITION to get the  
proper image.  
Picture bounces  
or a wave pattern  
is present in the  
picture.  
Keep the devices that may cause electrical interference  
away from the monitor.  
‹q  
See the FCC information at the front cover of the manual.  
Color looks  
blotchy.  
Operate DEGAUSSING once.  
Picture is blurred.  
Adjust CONTRAST and BRIGHTNESS.  
‹q  
Operate DEGAUSSING once.  
Edges of available  
area on the screen  
are not straight.  
Adjust PINCUSHION / TRAPEZOID .  
11  
APPENDIX  
DESCRIPTION FOR D-SUB CONNECTOR  
Pin  
Signal  
1
1
2
Red  
Green  
3
4
5
6
Blue  
GND  
GND (Self -Test)  
GND - Red  
6
10  
15  
7
8
GND - Green  
GND - Blue  
9
No Pin  
10  
11  
12  
13  
14  
15  
GND - H.Sync  
GND-V.Sync  
Bi-directional Data (SDA)  
Horizontal Sync  
Vertical Sync (VCLK)  
Data Clock (SCL)  
*GND = Ground  
S/N: 9978623903  

HP Hewlett Packard PAVILION VF52 User Manual
Hobart Corp Convection Oven KA7E User Manual
Heath Zenith DESA SPECIALTY PRODUCTSTM SL 5210 User Manual
Go Video VR3845 User Manual
GE JBP95 User Manual
GE Electric Built In JP328 JP626 User Manual
GE 25829 User Manual
Electrolux CSIG 404 User Manual
Bose 3 2 1 GS Series II, 3 2 1 Series II User Manual
Asus Computer Hardware C8HM70I User Manual