5” LCD
Color Monitor
OWNER’S MANUAL
OWNER’S MANUAL
In extremely cold temperatures, the movement of the picture may be slow
and the picture may be dark, but this is not a malfunction. The set will work
normally once the temperature increases.
Small black and shiny dots inside the liquid crystal panel are normal for liquid
crystal product.
DESCRIPTION
The VMA5091 is a TFT active matrix color LCD monitor which delivers a striking
picture and superior image resolution. The VMA5091 can be used to enjoy video
images with the Clarion video sources, even if no TV tuner is connected.
PACKAGE CONTENTS
5" monitor
Headrest Mounting Bezel
Two Trim Rings
5m long cable with 3 male connectors (Video, Power/Ground, 3.5m IR)
Hardware (One 1/4-20 with nut and washer)
BUTTON AND CONNECTOR LOCATIONS
1
5
7
8
4
3
2
6
9
1
2
3
4
5
Power Button
6
7
8
9
8 Pin DIN Pigtail
Video Input
IR Sensor
Picture Select Down
Picture Select Up
Picture Control Button
Power Connector
IR Remote Out
VMA5091
WIRING PRECAUTIONS
Read all wiring precautions. If you are not sure of the connections, contact your
authorized Clarion dealer.
1. Disconnect the negative (-) lead of the battery before making any power
connections.
2. When creating passage holes for the power wires, use grommets to elimi-
nate any sharp edges created during drilling. This will protect the wire from
being nicked and causing a short circuit.
3. When connecting the ground lead, fasten the ground lead (black) securely to
a clean metal plate on the vehicle.
NOTE: The VMA5091 monitor displays video images only. It does not provide
audio output. Refer to the owner's manual of the connected device for informa-
tion on audio output.
INSTALLATION
The VMA5091 is a 5" monitor with an Infrared (IR) eye. It will accept a video
signal from any video source with composite video out. The IR eye will work
directly with any Clarion video source product with an IR Eye Input.
1. Install Mounting Bezel in vehicle headrest.
2. Once a location has been determined, connect the IR, Video RCAs and
power cables to the designated sources.
3. Feed the cables through the mounting location.
4. Plug the cable into the monitor's 8 Pin Din connector. Mount the monitor in
the designated mounting bezel.
8 Pin Mini DIN Connector
1
2
3
4
5
6
7
8
DC 12V
IR Out
Ground
Video Input
A/V Signal Ground
NC
NC
NC
VIDEO
IN
ACCESSORY (RED)
GROUND (BLACK)
IR REMOTE
OUT
OWNER’S MANUAL
MOUNTING OPTIONS
Your Clarion VMA5091 monitor comes with a special mounting bezel, perfect for
headrest mounting applications. The included trim rings allow the monitor to be
installed at various angles to guarantee a perfect install. In addition to this
mounting bezel, the VMA5091 has a 1/4-20 threaded hole as well as a slot on
the back to accommodate a variety of mounting options.
Trim
1/4-20 Threaded
Insert
Ring
Mounting
Bezel
Monitor
PICTURE ADJUSTMENT
To adjust the picture brightness, contrast, tint, color, etc., use the Picture + and -
buttons located on the front panel of the VMA5091. Press the + button to
increase the picture brightness, contrast, etc. Press the - button to decrease
the picture brightness, contrast, etc.
CARE AND MAINTENANCE
Cleaning the cabinet:
Use a soft, dry cloth to gently wipe off any dirt.
Do not use benzene, thinner, car cleaner, etc., as these substances may
damage the cabinet or cause the paint to peel.
Cleaning the LCD panel:
Use a soft, dry cloth to gently wipe off any dust.
The surface is easily scratched; do not rub it with hard objects.
VMA5091
SPECIFICATIONS
GENERAL SPECIFICATIONS:
Power Requirement:
Power Consumption:
Weight:
DC 12V (9-16V)
0.8A Max. (0.8A or Less)
1.3lb (0.6kg)
Dimensions:
5.5" x 4.4" x 1.2"
(140 x 110.9 x 30 mm) (W x H x D)
41 - 104 degrees F
Extension Cable with (male connectors
Video Input Power Connector, 3.5mm IR
Remote Out), Mounting Bezel, 2 Trim Rings
Operation Temperature:
Supplied Accessories:
MONITOR SPECIFICATIONS:
Display Type:
Screen Size:
Color TFT Active Matrix LCD
5" screen
Pixels:
600 x 234
Screen Resolution:
Video System:
140,400 Dots
NTSC/PAL
OWNER’S MANUAL
NOTES:
|