Cisco Systems Cisco MGX 8800 User Manual

About This Guide

This section desribes the audience, purpose, and organization of the Cisco MGX 8800/8900 Series

Hardware Installation Guide. It also explains the conventions used to present information in this guide.

Audience

Purpose

This guide is intended for use by installers, operators, network designers, and managers responsible for

installing, configuring, or maintaining Cisco MGX switches or media gateways. These users should be

familiar with telecommunications products and networking systems.

This hardware installation guide describes how to set up and install the Cisco MGX 8850, Cisco MGX

8850/B, Cisco MGX 8950, Cisco MGX 8830 and Cisco MGX 8830/B switches. It also describes how to

setup and install the MGX 8880 Media Gateway.

After completing the installation procedures covered in this guide, refer to the appropriate related

documents to configure the switch or gateway. Refer to “Documentation” later in this preface for

guidance on which documents to use.

Organization

This guide is organized as follows:

•

Chapter 1, “Product Overviews,” provides an overview of the MGX switches, MGX media gateway,

and their related components.

•

Chapter 2, “Illustrated Card List for MGX Switches and the MGX 8880 Media Gateway,” provides

an overview of all cards used in Cisco MGX switches and the MGX 8880 Media Gateway from

MGX software Releases 2 through 5.1.

•

Chapter 3, “Preparing for Installation,” lists site specifications and tools required for installing each

switch or gateway and its related components.

Chapter 4, “Planning for Card Redundancy, Line Redundancy, and Bulk Distribution,” describes

how to plan for card redundancy, line redundancy, and bulk distribution.

Chapter 5, “Installing the Cisco MGX Switch or Gateway,” contains procedures for installing each

Cisco MGX chassis, whether in a rack or in a Cisco-supplied cabinet.

Cisco MGX 8800/8900 Series Hardware Installation Guide

Releases 2 - 5.2, Part Number OL-4545-01, Rev. H0, May 2006

xxxiii

Scope of this Guide

Table 1

Conventions Used in this Guide (continued)

Convention

{ }

Definition

Sample

offset-list {in | out} offset

Braces indicate a required choice.

[{ }]

Braces within a bracket indicate a required [{letter\number}Enter]

choice within an optional element.

Notes, Warnings, and Cautions

This section explains the conventions used for notes, warnings, and cautions.

Note

A Note highlights helpful information, such as suggestions or references to material not covered in the

guide.

Tip

Caution

Warning

A Tip contains information that might help you solve a problem or save time.

A Caution emphasizes a situation in which equipment can be damaged or data can be corrupted or lost.

A Warning emphasizes a safety concern, where a very serious and hazardous situation could result if

instructions are not carefully adhered to.

Notes about Warnings

Warnings used in this document are translated into many languages in the Regulatory Compliance and

Safety Information for Cisco Multiservice Switch Products (MGX, BPX, and SES).

There are 3 types of Warnings in hardware guides:

•

EMC (electromagnetic compatibility)

Safety

Telecom

Warning statements are numbered. The numbering makes it clearer which Warning translation goes with

which source Warning.

Scope of this Guide

This guide consolidates the following guides into one document and adds information about MGX

Release 5 (and greater) hardware features. Thus, this guide covers all MGX switches supported by

software Release 2.0 through 5.1, and makes the following guides obsolete:

•

Cisco MGX 8850 Hardware Installation Guide, Release 2

Cisco MGX 8850 Hardware Installation Guide, Release 2.1

Cisco MGX 8800/8900 Series Hardware Installation Guide

Releases 2 - 5.2, Part Number OL-4545-01, Rev. H0, May 2006

xxxv

Scope of this Guide

•

Cisco MGX 8950 Hardware Installation Guide, Release 2.1

Cisco MGX 8850 (PXM45 and PXM1E) Hardware Installation Guide, Release 3

Cisco MGX 8950 Hardware Installation Guide, Release 3

Cisco MGX 8830 Hardware Installation Guide, Release 3

Cisco MGX 8850 (PXM1E/PXM45), Cisco MGX 8950, and Cisco MGX 8830 Hardware Installation

Guide, Releases 2 Through 4

New Hardware Introduced in Releases 4.0.10 through 5.3

This guide was updated to describe the modules and hardware introduced in MGX Releases 4.0.10

through 5.1 (see Table 2).

Table 2

Hardware Introduced in Releases 4.0.10 or 5.3, by Chassis

Hardware Introduced in MGX

Release 4.0.10 through 5.1

MGX 8850 MGX 8850 MGX

MGX

MGX 8830 8830/B

MGX

MGX 8950 8880

(PXM1E)

(PXM45)

8850/B

MGX 8880 Media Gateway

MGX 8850/B

—

MGX 8830/B

—

AXSM-16-155-XG 16-port OC3

Module with VSVD

MGX8950-EXTDR-CONconnector —

card

—

RCON-IT05-8850 connector card¹

RCON-IT03-8850 connector card¹

RCON-IT03-8830 connector card¹

—

MGX-VXSM-4-155 Voice Switch

Service Module (VXSM),

4 OC3/STM-1

—

MGX-VXSM-48T1E1 Voice Switch —

Service Module (VXSM)

—

MPSM-8-T1E1Multiprotocol

Service Module

—

MPSM-T3E3-155 Multiprotocol

Service Module

MPSM-16-T1E1 Multiprotocol

Service Module

SRME/B Enhanced Service

Resource Module

MGX-VXSM-T3

—

1. Pre-installed in chassis.

Cisco MGX 8800/8900 Series Hardware Installation Guide

Releases 2 - 5.2, Part Number OL-4545-01, Rev. H0, May 2006

xxxvi

Documentation

New Back Cards Introduced in Releases 4.0.10 through 5.3

The following back cards were introduced in MGX Releases 4.0.10 through 5.1:

BNC-3-T3E3 3-port T3E3

MCC-16-E1-1N

•

MGX-2GE

MGX-2OC12POS

MGX-BNC-3T3-M

MGX-STM1-EL-1

RBBN-16-T1E1-1N

RED-16-T1E1

SFP-2-155

SMB-2-155-EL

VXSM-BC-3T3

MGX-RJ45-5-ETH

Documentation

A Finding Cisco User Documentation Online document ships with your product. That guide contains

general information about how to locate Cisco MGX, BPX, SES, and CWM documentation online.

Documentation Notes for these Product Releases

This release includes new hardware or features for the following releases:

•

Cisco MGX Release 5.2 introduces the Cisco MGX 8850/B multiservice switch

Cisco MGX Release 5.2, for these multiservice switches:

–

Cisco MGX 8850 (PXM1E)

Cisco MGX 8850 (PXM45)

Cisco MGX 8950

Cisco MGX 8830

•

Cisco MGX Release 1.3, for these multiservice switches:

–

Cisco MGX 8850 (PXM1)

Cisco MGX 8230

Cisco MGX 8250

•

Cisco MGX Release 5.2, for the Route Processor Modules (RPM-XF and RPM-PR)

Cisco WAN Manager Release 15.1. CWM Release 15 introduced a helpful new documentation

feature: web-based online help. To invoke online help, press F1 on a PC, press the Help key on a

UNIX workstation, or select Help from the main or popup menu. Cisco WAN Manager online help

has been updated for Release 15.1.

Cisco MGX 8800/8900 Series Hardware Installation Guide

Releases 2 - 5.2, Part Number OL-4545-01, Rev. H0, May 2006

xxxvii

Documentation

Other components of multiservice WAN products, such as the Service Expansion Shelf (SES) and WAN

switching software have no new features for this release.

Related Documentation

This section describes the user guides and release notes that support this release of Cisco Multiservice

Switch products.

User Guide—Order of Use

Use the guides listed here in the following order:

Step 1

Refer to the documents that ship with your product. Observe all safety precautions.

•

Regulatory Compliance and Safety Information for Cisco Multiservice Switch Products (MGX, BPX,

and SES)—This document familiarizes you with safety precautions for your product.

•

Finding Cisco User Documentation Online—This document explains how to find documentation for

MGX, BPX, and SES multiservice switches and media gateways as well as CWM network

management software. These documents are available only online.

•

Installation Warning Card—This document provides precautions about installing your cards. It

explains such subjects as removing the shipping tab and inserting cards properly into the correct

slots.

Step 2

Step 3

Refer to the release notes for your product.

If your network uses the CWM network management system, upgrade CWM. (If you are going to install

CWM for the first time, do so after Step 4.) Upgrade instructions are included in the following

documents:

•

Cisco WAN Manager Installation Guide, Release 15.3.00

Cisco WAN Manager User’s Guide, Release 15.3.00

Step 4

Step 5

If your network contains MGX and SES products, refer to this guide for planning information:

Cisco PNNI Network Planning Guide for MGX and SES Products

Refer to these guides for information about installing cards and cables in the MGX chassis:

•

Cisco MGX 8800/8900 Hardware Installation Guide, Releases 2 - 5.3 for installing cards and cables

in these chassis.

•

Cisco MGX 8xxx Edge Concentrator Installation and Configuration Guide for installing cards and

cables in the Cisco MGX 8230, Cisco MGX 8250, or Cisco MGX 8850 (PXM1) chassis.

Step 6

Step 7

Refer to the guides that help you configure your MGX switch and processor cards:

•

Cisco MGX 8800/8900 Series Configuration Guide, Release 5.2 for these chassis.

Cisco MGX 8xxx Edge Concentrator Installation and Configuration Guide for the Cisco MGX 8230,

Cisco MGX 8250, or Cisco MGX 8850 (PXM1) chassis.

Refer to the guide that supports the additional cards you intend to install in your switch. For example:

•

Services guides can help you establish ATM, Frame Relay, or circuit emulation services on your

switch.

•

VISM guides can help you set up your switch as a voice gateway, and an RPM guide can help you

implement IP on the switch.

Cisco MGX 8800/8900 Series Hardware Installation Guide

Releases 2 - 5.2, Part Number OL-4545-01, Rev. H0, May 2006

xxxviii

Documentation

Step 8

Note

Additional guides, such as command reference guides and error message documentation, can help with

the daily operation and maintenance of your switch.

User guide titles may be different for earlier software releases. The titles shown in Table 3 are for the

September 2005 release.

User Guide Titles and Descriptions

Table 3 lists the technical guides and release notes that support the September 2005 multiservice switch

product releases. User documentation and release notes in Table 3 are listed in order of use and include

information about which multiservice switch or media gateway the document supports.

The Cisco MGX 8230, Cisco MGX 8250, and Cisco MGX 8850 (PXM1) switch documentation was not

updated for the September 2005 release. Therefore, some information about configuring and using the

new MPSM-8-T1E1 card in these switches is included in the following guides:

•

Cisco ATM Services (AUSM/MPSM-8-T1E1) Configuration Guide and Command Reference for

MGX Switches, Release 5.2

Cisco Frame Relay Services (FRSM/MPSM-8-T1E1) Configuration Guide and Command Reference

for MGX Switches, Release 5.2

Cisco Circuit Emulation Services (CESM/MPSM-8-T1E1) Configuration Guide and Command

Reference for MGX Switches, Release 5.2

Information about how to install or upgrade to the MPSM-8-T1E1 card in Cisco MGX 8230, Cisco

MGX 8250, and Cisco MGX 8850 (PXM1) switches is in the Release Notes for Cisco MGX 8230, Cisco

MGX 8250, and Cisco MGX 8850 (PXM1) Switches, Release 1.3.14.

Note

Refer to each product’s release notes for the latest information on features, bug fixes, and more.

Terms

Two main types of ATM cards are used in MGX switches: AXSM and AUSM. AXSM stands for ATM

Switching Service Module. AUSM stands for ATM UNI (User Network Interface) Service Module.

CWM stands for Cisco WAN Manager, our multiservice switch network management system.

Legacy service module refers to a previously introduced card. For this release, the term is used

specifically for the CESM-8-T1E1, FRSM-8-T1E1, and AUSM-8-T1E1 cards, which can now be

replaced by the new MPSM-8-T1E1 card.

MPSM stands for Multiprotocol Service Module.

RPM stands for Route Processor Module.

SES stands for Service Expansion Shelf.

VISM stands for Voice Interworking Service Module.

VXSM stands for Voice Switch Service Module.

Cisco MGX 8800/8900 Series Hardware Installation Guide

Releases 2 - 5.2, Part Number OL-4545-01, Rev. H0, May 2006

xxxix

Documentation

Table 3

User Guides and Release Notes for Cisco MGX and BPX Switches and Media Gateways

MGX

8850

MGX

8850

MGX

8850

BPX

MGX

with SES 8230 Rel. 8250 Rel. (PXM1)

8830

(PXM1E) (PXM45) 8950

8880

Document Title and Part Number

Overview and Safety Documents

Rel. 4

1.3

Rel. 1.3

Rel. 5.3

Rel. 5.3.

Finding Cisco User Documentation

Online

DOC-7814807=

Installation Warning Card

DOC-7812348=

Regulatory Compliance and Safety

Information for Cisco Multiservice

Switch Products (MGX, BPX, and

SES)

DOC-7814790=

Release Notes for the Cisco MGX

8880 Media Gateway, Release

5.3.00

—

OL-8892-01

Release Notes for Cisco MGX 8850

(PXM1E/PXM45), Cisco MGX

8950, and Cisco MGX 8830

Switches, Release 5.3.00

OL-8891-01

Release Notes for Cisco MGX 8230,

Cisco MGX 8250, and Cisco MGX

8850 (PXM1) Switches, Release

1.3.14

—

OL-8973-01

Release Notes for the Cisco Voice

Switch Service Module (VXSM),

Release 5.3.00

—

OL-10285-01

Release Notes for Cisco WAN

Manager, Release 15.3.00

OL-10216-01

Release Notes for the Cisco Voice

Interworking Service Module

(VISM), Release 3.3.25

—

OL-8428-01

Cisco MGX 8800/8900 Series Hardware Installation Guide

Releases 2 - 5.2, Part Number OL-4545-01, Rev. H0, May 2006

Documentation

Table 3

User Guides and Release Notes for Cisco MGX and BPX Switches and Media Gateways (continued)

MGX

8850

MGX

8850

MGX

8850

BPX

MGX

with SES 8230 Rel. 8250 Rel. (PXM1)

8830

(PXM1E) (PXM45) 8950

8880

Document Title and Part Number

Rel. 4

1.3

Rel. 1.3

Rel. 5.3

Rel. 5.3.

Release Notes for Cisco MGX

Route Processor Module (RPM-XF)

IOS Release 12.4(6)T1 for

PXM45-based Switches, Release

5.3.00

—

OL-8893-01

Release Notes for Cisco MGX

Route Processor Module (RPM-PR)

IOS Release 12.4(6)T1 for MGX

Releases 1.3.14 and 5.3.00

—

OL-8894-01

Cisco MGX 8230 Edge

Concentrator Overview, Release

1.1.3¹

—

DOC-7812899=

Cisco MGX 8250 Edge

Concentrator Overview, Release

1.1.3¹

—

DOC-7811576=

Cisco MGX 8850 Multiservice

Switch Overview, Release 1.1.3¹

—

OL-1154-01

Hardware Installation Guides

Cisco MGX 8800/8900 Hardware

Installation Guide, Releases 2 - 5.3

—

OL-4545-01

Cisco Service Expansion Shelf

Hardware Installation Guide,

Release 1¹

—

DOC-786122=

Planning and Configuration Guides

Cisco PNNI Network Planning

Guide for MGX and SES Products

—

OL-3847-01

Cisco MGX 8800/8900 Series

—

Configuration Guide, Release 5.2

OL-6482-01

Cisco MGX 8800/8900 Series Hardware Installation Guide

Releases 2 - 5.2, Part Number OL-4545-01, Rev. H0, May 2006

xli

Documentation

Table 3

User Guides and Release Notes for Cisco MGX and BPX Switches and Media Gateways (continued)

MGX

8850

MGX

8850

MGX

8850

BPX

MGX

with SES 8230 Rel. 8250 Rel. (PXM1)

8830

(PXM1E) (PXM45) 8950

8880

Document Title and Part Number

Rel. 4

1.3

Rel. 1.3

Rel. 5.3

Rel. 5.3.

Cisco WAN Manager Installation

Guide, Release 15.3.00

OL-10358-01

Cisco WAN Manager User’s Guide,

Release 15.3.00

OL-10427-01

Cisco MGX 8850 Edge

—

Concentrator Installation and

Configuration, Release 1.1.3¹

DOC-7811223=

Cisco SES PNNI Controller

Software Configuration Guide,

Release 3¹

—

DOC-7814258=

Cisco MGX 8230 Edge

—

Concentrator Installation and

Configuration, Release 1.1.3¹

DOC-7811215=

Cisco MGX 8250 Edge

—

Concentrator Installation and

Configuration, Release 1.1.3¹

DOC-7811217=

Service Module Configuration and Reference Guides

Cisco MGX Route Processor

—

Module (RPM-PR) Installation and

Configuration Guide, Release 5.2¹

OL-7349-01

Frame Relay Software

—

Configuration Guide and Command

Reference for the Cisco MGX 8850

FRSM12 Card, Release 3¹

DOC-7810327=

Cisco ATM Services

—

(AUSM/MPSM-8-T1E1)

Configuration Guide and Command

Reference for MGX Switches,

Release 5.2²

OL-6479-01

Cisco MGX 8800/8900 Series Hardware Installation Guide

Releases 2 - 5.2, Part Number OL-4545-01, Rev. H0, May 2006

xlii

Documentation

Table 3

User Guides and Release Notes for Cisco MGX and BPX Switches and Media Gateways (continued)

MGX

8850

MGX

8850

MGX

8850

BPX

MGX

with SES 8230 Rel. 8250 Rel. (PXM1)

8830

(PXM1E) (PXM45) 8950

8880

Document Title and Part Number

Rel. 4

1.3

Rel. 1.3

Rel. 5.3

Rel. 5.3.

Cisco Frame Relay Services

(FRSM/MPSM-8-T1E1)

Configuration Guide and Command

Reference for MGX Switches,

Release 5.2²

—

OL-6480-01

Cisco Circuit Emulation Services

(CESM/MPSM-8-T1E1)

—

Configuration Guide and Command

Reference for MGX Switches,

Release 5.2²

OL-6481-01

Cisco MGX Route Processor

—

Module (RPM-XF) Installation and

Configuration Guide, Release 5.2¹

OL-6594-01

Cisco ATM Services (AXSM)

Configuration Guide and Command

Reference for MGX Switches,

Release 5.2

OL-6484-01

Cisco ATM and Frame Relay

Services (MPSM-T3E3-155 and

MPSM-16-T1E1) Configuration

Guide and Command Reference for

MGX Switches, Release 5.2

—

OL-6487-01

Cisco Voice Switch Services

Configuration Guide for MGX

Switches and Media Gateways,

Release 5.3

—

OL-10284-01

Cisco Voice Interworking Services

(VISM) Configuration Guide and

Command Reference, Release 3.3

OL-5358-01

Reference Guides

Cisco MGX 8230 Multiservice

Gateway Error Messages, Release

1.1.3¹

—

DOC-78112113=

Cisco MGX 8800/8900 Series Hardware Installation Guide

Releases 2 - 5.2, Part Number OL-4545-01, Rev. H0, May 2006

xliii

Documentation

Table 3

User Guides and Release Notes for Cisco MGX and BPX Switches and Media Gateways (continued)

MGX

8850

MGX

8850

MGX

8850

BPX

MGX

with SES 8230 Rel. 8250 Rel. (PXM1)

8830

(PXM1E) (PXM45) 8950

8880

Document Title and Part Number

Rel. 4

1.3

Rel. 1.3

Rel. 5.3

Rel. 5.3.

Cisco MGX 8230 Multiservice

Gateway Command Reference,

Release 1.1.3¹

—

DOC-7811211=

Cisco MGX 8250 Multiservice

Gateway Command Reference,

Release 1.1.3¹

—

DOC-7811212=

Cisco MGX 8250 Multiservice

Gateway Error Messages, Release

1.1.3¹

DOC-7811216=

Cisco MGX 8800 Series Switch

Command Reference, Release

1.1.3¹

DOC-7811210=

Cisco MGX 8800 Series Switch

System Error Messages, Release

1.1.3¹

DOC-7811240=

Cisco SES PNNI Controller

—

Command Reference, Release 3¹

DOC-7814260=

Cisco MGX 8800/8900 Series

Command Reference, Release 5.2

—

OL-6483-01

Cisco Voice Switch Services

Command Reference for MGX

Switches and Media Gateways,

Release 5.3

—

OL-10283-01

Cisco WAN Manager SNMP Service

Agent, Release 15.3.00

OL-10190-01

Cisco WAN Manager Database

Interface Guide, Release 15.3.00

OL-10140-01

1. This document was not updated for the September 2005 release.

Cisco MGX 8800/8900 Series Hardware Installation Guide

Releases 2 - 5.2, Part Number OL-4545-01, Rev. H0, May 2006

xliv

Documentation

2. Some configuration and command information is included in this guide for using the multiprotocol service module (MPSM-8-T1E1/MPSM-16-T1E1) in

a Cisco MGX 8230, MGX 8250, or MGX 8850 (PXM1) switch.

Note

For the September 2005 product release, there are no new features for the Service Expansion Shelf (SES)

of the BPX switch and BPX WAN switching software. Therefore, documentation for these items was not

updated. Table 3 lists the most recent user guides and release notes for these products.

Table 3 also lists the latest documentation available for the Cisco MGX 8230, Cisco MGX 8250, and

Cisco MGX 8850 (PXM1) switches. These switches use the PXM1 processor card. Although there are

new features in MGX Release 1.3 for these switches, only the release notes were updated. And the

following guides contain some information about configuring the MPSM-8-T1E1 and MPSM-16-T1E1

cards for use in these switches:

•

Cisco Circuit Emulation Services (CESM/MPSM-8-T1E1) Configuration Guide and Command

Reference for MGX Switches, Release 5.2

Cisco Frame Relay Services (FRSM/MPSM-8-T1E1) Configuration Guide and Command Reference

for MGX Switches, Release 5.2

Cisco ATM Services (AUSM/MPSM-8-T1E1) Configuration Guide and Command Reference for

MGX Switches, Release 5.2

Table 4 lists the documents that ship with product.

Table 5 contains alphabetized titles and descriptions of all the guides and release notes listed in Table 3.

Table 4

Documents that Ship with Multiservice Switch Products

Document Title

Description

Finding Cisco User Documentation Online

DOC-7817081=

Describes how to find the guides and release notes that support

multiservice switches and network management products.

These documents are available only online. This guide ships

with product.

Installation Warning Card

Contains precautions that you should take before you

insert a card into a slot. This Warning Card ships with

product.

DOC-7812348=

Regulatory Compliance and Safety Information for Cisco

Multiservice Switch Products (MGX, BPX, and SES)

Provides regulatory compliance information, product

warnings, and safety recommendations for all the Cisco MGX

multiservice switches: MGX 8230, MGX 8250, MGX 8850

(PXM1), MGX 8850 (PXM45), MGX 8850 (PXM1E), MGX

8830 and MGX 8950. Also provides such information for the

MGX 8880 Media Gateway. This guide ships with product.

DOC-7814790=

Cisco MGX 8800/8900 Series Hardware Installation Guide

Releases 2 - 5.2, Part Number OL-4545-01, Rev. H0, May 2006

xlv

Documentation

Table 5

User Guides and Release Notes for Cisco Multiservice Switch Products

Document Title

Description

Cisco ATM and Frame Relay Services (MPSM-T3E3-155 and Provides software configuration procedures for provisioning

MPSM-16-T1E1) Configuration Guide and Command

Reference for MGX Switches, Release 5.2

ATM and Frame Relay connections on the new

MPSM-T3E3-155 multiprotocol service module. Also

describes all MPSM-T3E3-155 commands.

OL-6487-01

Cisco ATM Services (AUSM/MPSM-8-T1E1) Configuration

Provides software configuration procedures for provisioning

Guide and Command Reference for MGX Switches, Release connections and managing the AUSM cards supported in this

5.2

release. Also describes all AUSM commands. Includes

software configuration procedures for provisioning

connections and managing the MPSM-8-T1E1 card as an

AUSM card replacement.

OL-6479-01

Cisco ATM Services (AXSM) Configuration Guide and

Command Reference for MGX Switches, Release 5.2

Explains how to configure the AXSM cards and provides a

command reference that describes the AXSM commands in

detail. The AXSM cards covered in this guide are the

AXSM-XG, AXSM/A, AXSM/B, AXSM-E, and

AXSM-32-T1E1-E.

OL-4548-01

Cisco Circuit Emulation Services (CESM/MPSM-8-T1E1)

Configuration Guide and Command Reference for MGX

Switches, Release 5.2

Provides software configuration procedures for provisioning

connections and managing the Circuit Emulation Service

Module (CESM) cards supported in this release. Also

describes all CESM commands. Includes software

configuration procedures for provisioning connections and

managing the MPSM-8-T1E1 card as a CESM card

replacement.

OL-6481-01

Cisco Frame Relay Services (FRSM/MPSM-8-T1E1)

Configuration Guide and Command Reference for MGX

Switches, Release 5.2

Provides software configuration procedures for provisioning

connections and managing the Frame Relay Service Module

(FRSM) cards supported in this release. Also describes all

FRSM commands. Includes software configuration

procedures for provisioning connections and managing the

MPSM-8-T1E1 card as an FRSM card replacement.

OL-6480-01

Cisco MGX 8230 Edge Concentrator Installation and

Configuration, Release 1.1.3

Provides installation instructions for the Cisco MGX 8230

edge concentrator.

DOC-7811215=

Cisco MGX 8230 Edge Concentrator Overview, Release 1.1.3 Describes the system components and function of the

Cisco MGX 8250 edge concentrator.

DOC-7812899=

Cisco MGX 8230 Multiservice Gateway Command Reference, Provides detailed information on the general command line

Release 1.1.3

interface commands.

DOC-7811211=

Cisco MGX 8230 Multiservice Gateway Error Messages,

Release 1.1.3

Provides error message descriptions and recovery

procedures.

DOC-78112113=

Cisco MGX 8250 Edge Concentrator Installation and

Configuration, Release 1.1.3

Provides installation instructions for the Cisco MGX 8250

edge concentrator.

DOC-7811217=

Cisco MGX 8800/8900 Series Hardware Installation Guide

Releases 2 - 5.2, Part Number OL-4545-01, Rev. H0, May 2006

xlvi

Documentation

Table 5

User Guides and Release Notes for Cisco Multiservice Switch Products (continued)

Description

Document Title

Cisco MGX 8250 Edge Concentrator Overview, Release 1.1.3 Describes the system components and function of the

Cisco MGX 8250 edge concentrator.

DOC-7811576=

Cisco MGX 8250 Multiservice Gateway Command Reference, Provides detailed information on the general command line

Release 1.1.3

interface commands.

DOC-7811212=

Cisco MGX 8250 Multiservice Gateway Error Messages,

Release 1.1.3

Provides error message descriptions and recovery

procedures.

DOC-7811216=

Cisco MGX 8800 Series Switch Command Reference, Release Provides detailed information on the general command line

1.1.3

for the Cisco MGX 8850 (PXM1), Cisco MGX 8250, and

Cisco MGX 8230 edge concentrators.

DOC-7811210=

Cisco MGX 8800 Series Switch System Error Messages,

Release 1.1.3

Provides error message descriptions and recovery procedures

for Cisco MGX 8850 (PXM1), Cisco MGX 8250, and

Cisco MGX 8230 edge concentrators.

DOC-7811240=

Cisco MGX 8800/8900 Hardware Installation Guide,

Releases 2 - 5.3

Describes how to install the Cisco MGX 8950, the

Cisco MGX 8850 (PXM1E/PXM45), the Cisco MGX

8850/B (PXM1E/PXM45), and the Cisco MGX 8830

switches. Also describes how to install the MGX 8880 Media

Gateway. This document explains what each switch does and

covers site preparation, grounding, safety, card installation,

and cabling. The Cisco MGX 8850 switch uses either a

PXM45 or a PXM1E controller card and provides support for

both serial bus-based and cell bus-based service modules.

The Cisco MGX 8830 switch uses a PXM1E controller card

and supports cell bus-based service modules. The Cisco

MGX 8950 supports only serial bus-based service modules.

The Cisco MGX 8880 uses a PXM45/C controller card, and

supports only serial bus-based service modules. This

hardware installation guide replaces all previous hardware

guides for these switches.

OL-4545-01

Cisco MGX 8800/8900 Series Configuration Guide, Release Describes how to configure the Cisco MGX 8880 Media

5.2

Gateway. Also describes how to configure Cisco MGX 8850

(PXM1E), Cisco MGX 8850 (PXM45), the Cisco MGX

8850/B (PXM1E/PXM45), and Cisco MGX 8830 switches to

operate as ATM edge switches and the Cisco MGX 8950

switch to operate as a core switch. This guide also provides

some operation and maintenance procedures.

OL-6482-01

Cisco MGX 8800/8900 Series Command Reference, Release Describes the PXM commands that are available in the CLI

5.2

of the Cisco MGX 8850 (PXM45), Cisco MGX 8850

(PXM1E), Cisco MGX 8950, and Cisco MGX 8830 switches.

Also describes the PXM commands that are available in the

CLI of the Cisco MGX 8880 Media Gateway.

OL-6483-01

Cisco MGX 8800/8900 Series Hardware Installation Guide

Releases 2 - 5.2, Part Number OL-4545-01, Rev. H0, May 2006

xlvii

Documentation

Table 5

User Guides and Release Notes for Cisco Multiservice Switch Products (continued)

Document Title

Description

Cisco MGX 8850 Edge Concentrator Installation and

Configuration, Release 1.1.3

Provides installation instructions for the Cisco MGX 8850

(PXM1) edge concentrator.

DOC-7811223=

Cisco MGX 8850 Multiservice Switch Overview, Release 1.1.3 Describes the system components and function of the

Cisco MGX 8850 (PXM1) edge concentrator.

OL-1154-01

Cisco MGX and Service Expansion Shelf Error Messages,

Release 5.0

Provides error message descriptions and recovery

procedures.

OL-6485-01

Cisco MGX Route Processor Module (RPM-XF) Installation Describes how to install and configure the Cisco MGX Route

and Configuration Guide, Release 5.2

Processor Module (RPM-XF) in the Cisco MGX 8850

(PXM45), Cisco MGX 8880 (PXM45), and Cisco MGX 8950

switch. Also provides site preparation procedures,

troubleshooting procedures, maintenance procedures, cable

and connector specifications, and basic Cisco IOS

configuration information.

OL-6954-01

Cisco MGX Route Processor Module (RPM-PR) Installation Describes how to install and configure the Cisco MGX Route

and Configuration Guide, Release 5.2

Processor Module (RPM/B or RPM-PR) in the

Cisco MGX 8850 (PXM1), the Cisco MGX 8250, and the

Cisco MGX 8230 edge concentrators. Also provides site

preparation procedures, troubleshooting procedures,

maintenance procedures, cable and connector specifications,

and basic Cisco IOS configuration information.

OL-7349-01

Cisco PNNI Network Planning Guide for MGX and SES

Products

Provides guidelines for planning a PNNI network that uses

Cisco MGX 8830, Cisco MGX 8850 (PXM45 and PXM1E),

Cisco MGX 8950, or Cisco BPX 8600 switches or the

MGX 8880 Media Gateway. When connected to a PNNI

network, each Cisco BPX 8600 Series switch requires an SES

for PNNI route processing.

OL-3847-01

Cisco Service Expansion Shelf Hardware Installation Guide, Provides instructions for installing and maintaining an SES

Release 1

controller.

DOC-786122=

Cisco SES PNNI Controller Command Reference, Release 3 Describes the commands used to configure and operate the

SES PNNI controller.

DOC-7814260=

Cisco SES PNNI Controller Software Configuration Guide,

Release 3

Describes how to configure, operate, and maintain the SES

PNNI controller.

DOC-7814258=

Cisco Voice Interworking Services (VISM) Configuration

Guide and Command Reference, Release 3.3

Describes how to install and configure the Voice

Interworking Service Module (VISM) in the Cisco

MGX 8830, Cisco MGX 8850 (PXM45), and Cisco MGX

8850 (PXM1E) multiservice switches. Provides site

preparation procedures, troubleshooting procedures,

maintenance procedures, cable and connector specifications,

and Cisco CLI configuration information.

OL-5358-01

Cisco MGX 8800/8900 Series Hardware Installation Guide

Releases 2 - 5.2, Part Number OL-4545-01, Rev. H0, May 2006

xlviii

Documentation

Table 5

User Guides and Release Notes for Cisco Multiservice Switch Products (continued)

Document Title

Description

Cisco Voice Switch Services (VXSM) Configuration and

Command Reference Guide for MGX Switches, Release 5

Describes the features and functions of the new Voice Switch

Service Module (VXSM) in the Cisco MGX 8880 Media

Gateway and in the Cisco MGX8850 (PXM45 and PXM1E)

multiservice switches. Also provides configuration

procedures, troubleshooting procedures, and Cisco CLI

configuration information.

OL-4625-01

Cisco WAN Manager Database Interface Guide, Release

15.3.00

Provides information about accessing the CWM Informix

database that is used to store information about the network

elements.

OL-6261-01

Cisco WAN Manager Installation Guide, Release 15.3.00

Provides procedures for installing Release 15.1 of the CWM

network management system.

OL-6259-01

Cisco WAN Manager SNMP Service Agent, Release 15.3.00 Provides information about the CWM Simple Network

Management Protocol service agent, an optional adjunct to

CWM that is used for managing Cisco WAN switches

through SNMP.

OL-6260-01

Cisco WAN Manager User’s Guide, Release 15.3.00

Describes how to use the CWM Release 15.1 software, which

consists of user applications and tools for network

management, connection management, network

OL-6257-01

configuration, statistics collection, and security management.

Note

The CWM interface now has built-in documentation

support in the form of online Help. On a PC, press F1

to access Help; on a UNIX workstation, press the

Help key. Alternatively, on either system you can

select Help from the main or popup menu.

Frame Relay Software Configuration Guide and Command

Describes how to use the high-speed Frame Relay

Reference for the Cisco MGX 8850 FRSM12 Card, Release 3 (FRSM-12-T3E3) commands that are available in the CLI of

the Cisco MGX 8850 (PXM45) switch.

DOC-7810327=

Release Notes for Cisco MGX 8230, Cisco MGX 8250, and

Cisco MGX 8850 (PXM1) Switches, Release 1.3.14

Provides new feature, upgrade, and compatibility

information, as well as information about known and

resolved anomalies.

OL-4539-01

Release Notes for Cisco MGX 8850 (PXM1E/PXM45), Cisco Provides new feature, upgrade, and compatibility

MGX 8950, and Cisco MGX 8830 Switches, Release 5.3.00

information, as well as information about known and

resolved anomalies.

OL-6478-01

Release Notes for the Cisco MGX 8880 Media Gateway,

Release 5.3.00

Provides new feature and compatibility information, as well

as information about known and resolved anomalies.

OL-6493-01

Release Notes for Cisco MGX Route Processor Module

Provides upgrade and compatibility information, as well as

(RPM-PR) IOS Release 12.4(6)T1 for MGX Releases 1.3.14 information about known and resolved anomalies.

and 5.3.00

OL-7292-01

Cisco MGX 8800/8900 Series Hardware Installation Guide

Releases 2 - 5.2, Part Number OL-4545-01, Rev. H0, May 2006

xlix

Obtaining Documentation

Table 5

User Guides and Release Notes for Cisco Multiservice Switch Products (continued)

Document Title

Description

Release Notes for Cisco MGX Route Processor Module

Provides upgrade and compatibility information, as well as

(RPM-XF) IOS Release 12.4(6)T1 for PXM45-based Switches, information about known and resolved anomalies.

Release 5.3.00

OL-7059-01

Release Notes for the Cisco Voice Interworking Service

Module (VISM), Release 3.3.25

Provides new feature, upgrade, and compatibility

information, as well as information about known and

resolved anomalies.

OL-5357-01

Release Notes for the Cisco Voice Switch Service Module

(VXSM), Release 5.3.00

Provides new feature, upgrade, and compatibility

information, as well as information about known and

resolved anomalies.

OL-7088-01

Release Notes for Cisco WAN Manager, Release 15.3.00

Provides new feature, upgrade, and compatibility

information, as well as information about known and

resolved anomalies.

OL-6495-01

Obtaining Documentation

Cisco documentation and additional literature are available on Cisco.com. Cisco also provides several

ways to obtain technical assistance and other technical resources. These sections explain how to obtain

technical information from Cisco Systems.

Cisco.com

You can access the most current Cisco documentation at this URL:

http://www.cisco.com/techsupport

You can access the Cisco website at this URL:

http://www.cisco.com

You can access international Cisco websites at this URL:

http://www.cisco.com/public/countries_languages.shtml

Product Documentation DVD

The Product Documentation DVD is a comprehensive library of technical product documentation on a

portable medium. The DVD enables you to access multiple versions of installation, configuration, and

command guides for Cisco hardware and software products. With the DVD, you have access to the same

HTML documentation that is found on the Cisco website without being connected to the Internet.

Certain products also have .PDF versions of the documentation available.

The Product Documentation DVD is available as a single unit or as a subscription. Registered Cisco.com

users (Cisco direct customers) can order a Product Documentation DVD (product number

DOC-DOCDVD= or DOC-DOCDVD=SUB) from Cisco Marketplace at this URL:

http://www.cisco.com/go/marketplace/

Cisco MGX 8800/8900 Series Hardware Installation Guide

Releases 2 - 5.2, Part Number OL-4545-01, Rev. H0, May 2006

Documentation Feedback

Ordering Documentation

Registered Cisco.com users may order Cisco documentation at the Product Documentation Store in the

Cisco Marketplace at this URL:

http://www.cisco.com/go/marketplace/

Nonregistered Cisco.com users can order technical documentation from 8:00 a.m. to 5:00 p.m.

(0800 to 1700) PDT by calling 1 866 463-3487 in the United States and Canada, or elsewhere by

calling 011 408 519-5055. You can also order documentation by e-mail at

[email protected] or by fax at 1 408 519-5001 in the United States and Canada,

or elsewhere at 011 408 519-5001.

Documentation Feedback

You can rate and provide feedback about Cisco technical documents by completing the online feedback

form that appears with the technical documents on Cisco.com.

You can submit comments about Cisco documentation by using the response card (if present) behind the

front cover of your document or by writing to the following address:

Cisco Systems

Attn: Customer Document Ordering

170 West Tasman Drive

San Jose, CA 95134-9883

We appreciate your comments.

Cisco Product Security Overview

Cisco provides a free online Security Vulnerability Policy portal at this URL:

http://www.cisco.com/en/US/products/products_security_vulnerability_policy.html

From this site, you will find information about how to:

•

Report security vulnerabilities in Cisco products.

Obtain assistance with security incidents that involve Cisco products.

A current list of security advisories, security notices, and security responses for Cisco products is

available at this URL:

http://www.cisco.com/go/psirt

To see security advisories, security notices, and security responses as they are updated in real time, you

can subscribe to the Product Security Incident Response Team Really Simple Syndication (PSIRT RSS)

feed. Information about how to subscribe to the PSIRT RSS feed is found at this URL:

http://www.cisco.com/en/US/products/products_psirt_rss_feed.html

Cisco MGX 8800/8900 Series Hardware Installation Guide

Releases 2 - 5.2, Part Number OL-4545-01, Rev. H0, May 2006

Obtaining Technical Assistance

Reporting Security Problems in Cisco Products

Cisco is committed to delivering secure products. We test our products internally before we release them,

and we strive to correct all vulnerabilities quickly. If you think that you have identified a vulnerability

in a Cisco product, contact PSIRT:

•

For Emergencies only—[email protected]

An emergency is either a condition in which a system is under active attack or a condition for which

a severe and urgent security vulnerability should be reported. All other conditions are considered

nonemergencies.

•

For Nonemergencies—[email protected]

In an emergency, you can also reach PSIRT by telephone:

•

1 877 228-7302

1 408 525-6532

Tip

We encourage you to use Pretty Good Privacy (PGP) or a compatible product (for example, GnuPG) to

encrypt any sensitive information that you send to Cisco. PSIRT can work with information that has been

encrypted with PGP versions 2.x through 9.x.

Never use a revoked or an expired encryption key. The correct public key to use in your correspondence

with PSIRT is the one linked in the Contact Summary section of the Security Vulnerability Policy page

at this URL:

http://www.cisco.com/en/US/products/products_security_vulnerability_policy.html

The link on this page has the current PGP key ID in use.

If you do not have or use PGP, contact PSIRT at the aforementioned e-mail addresses or phone numbers

before sending any sensitive material to find other means of encrypting the data.

Obtaining Technical Assistance

Cisco Technical Support provides 24-hour-a-day award-winning technical assistance. The Cisco

Technical Support & Documentation website on Cisco.com features extensive online support resources.

In addition, if you have a valid Cisco service contract, Cisco Technical Assistance Center (TAC)

engineers provide telephone support. If you do not have a valid Cisco service contract, contact your

reseller.

Cisco Technical Support & Documentation Website

The Cisco Technical Support & Documentation website provides online documents and tools for

troubleshooting and resolving technical issues with Cisco products and technologies. The website is

available 24 hours a day, at this URL:

http://www.cisco.com/techsupport

Cisco MGX 8800/8900 Series Hardware Installation Guide

Releases 2 - 5.2, Part Number OL-4545-01, Rev. H0, May 2006

lii

Obtaining Technical Assistance

Access to all tools on the Cisco Technical Support & Documentation website requires a Cisco.com user

ID and password. If you have a valid service contract but do not have a user ID or password, you can

http://tools.cisco.com/RPF/register/register.do

Note

Use the Cisco Product Identification (CPI) tool to locate your product serial number before submitting

a web or phone request for service. You can access the CPI tool from the Cisco Technical Support &

Documentation website by clicking the Tools & Resources link under Documentation & Tools. Choose

Cisco Product Identification Tool from the Alphabetical Index drop-down list, or click the Cisco

Product Identification Tool link under Alerts & RMAs. The CPI tool offers three search options: by

product ID or model name; by tree view; or for certain products, by copying and pasting show command

output. Search results show an illustration of your product with the serial number label location

highlighted. Locate the serial number label on your product and record the information before placing a

service call.

Submitting a Service Request

Using the online TAC Service Request Tool is the fastest way to open S3 and S4 service requests. (S3

and S4 service requests are those in which your network is minimally impaired or for which you require

product information.) After you describe your situation, the TAC Service Request Tool provides

recommended solutions. If your issue is not resolved using the recommended resources, your service

request is assigned to a Cisco engineer. The TAC Service Request Tool is located at this URL:

http://www.cisco.com/techsupport/servicerequest

For S1 or S2 service requests, or if you do not have Internet access, contact the Cisco TAC by telephone.

(S1 or S2 service requests are those in which your production network is down or severely degraded.)

Cisco engineers are assigned immediately to S1 and S2 service requests to help keep your business

operations running smoothly.

To open a service request by telephone, use one of the following numbers:

Asia-Pacific: +61 2 8446 7411 (Australia: 1 800 805 227)

EMEA: +32 2 704 55 55

USA: 1 800 553-2447

For a complete list of Cisco TAC contacts, go to this URL:

http://www.cisco.com/techsupport/contacts

Definitions of Service Request Severity

To ensure that all service requests are reported in a standard format, Cisco has established severity

definitions.

Severity 1 (S1)—An existing network is down, or there is a critical impact to your business operations.

You and Cisco will commit all necessary resources around the clock to resolve the situation.

Severity 2 (S2)—Operation of an existing network is severely degraded, or significant aspects of your

business operations are negatively affected by inadequate performance of Cisco products. You and Cisco

will commit full-time resources during normal business hours to resolve the situation.

Cisco MGX 8800/8900 Series Hardware Installation Guide

Releases 2 - 5.2, Part Number OL-4545-01, Rev. H0, May 2006

liii

Obtaining Additional Publications and Information

Severity 3 (S3)—Operational performance of the network is impaired, while most business operations

remain functional. You and Cisco will commit resources during normal business hours to restore service

to satisfactory levels.

Severity 4 (S4)—You require information or assistance with Cisco product capabilities, installation, or

configuration. There is little or no effect on your business operations.

Obtaining Additional Publications and Information

Information about Cisco products, technologies, and network solutions is available from various online

and printed sources.

•

The Cisco Product Quick Reference Guide is a handy, compact reference tool that includes brief

product overviews, key features, sample part numbers, and abbreviated technical specifications for

many Cisco products that are sold through channel partners. It is updated twice a year and includes

the latest Cisco offerings. To order and find out more about the Cisco Product Quick Reference

Guide, go to this URL:

http://www.cisco.com/go/guide

•

Cisco Marketplace provides a variety of Cisco books, reference guides, documentation, and logo

merchandise. Visit Cisco Marketplace, the company store, at this URL:

http://www.cisco.com/go/marketplace/

Cisco Press publishes a wide range of general networking, training and certification titles. Both new

and experienced users will benefit from these publications. For current Cisco Press titles and other

information, go to Cisco Press at this URL:

http://www.ciscopress.com

•

Packet magazine is the Cisco Systems technical user magazine for maximizing Internet and

networking investments. Each quarter, Packet delivers coverage of the latest industry trends,

technology breakthroughs, and Cisco products and solutions, as well as network deployment and

troubleshooting tips, configuration examples, customer case studies, certification and training

information, and links to scores of in-depth online resources. You can access Packet magazine at

this URL:

http://www.cisco.com/packet

iQ Magazine is the quarterly publication from Cisco Systems designed to help growing companies

learn how they can use technology to increase revenue, streamline their business, and expand

services. The publication identifies the challenges facing these companies and the technologies to

help solve them, using real-world case studies and business strategies to help readers make sound

technology investment decisions. You can access iQ Magazine at this URL:

http://www.cisco.com/go/iqmagazine

or view the digital edition at this URL:

http://ciscoiq.texterity.com/ciscoiq/sample/

•

Internet Protocol Journal is a quarterly journal published by Cisco Systems for engineering

professionals involved in designing, developing, and operating public and private internets and

intranets. You can access the Internet Protocol Journal at this URL:

http://www.cisco.com/ipj

Cisco MGX 8800/8900 Series Hardware Installation Guide

Releases 2 - 5.2, Part Number OL-4545-01, Rev. H0, May 2006

liv

Obtaining Additional Publications and Information

•

Networking products offered by Cisco Systems, as well as customer support services, can be

obtained at this URL:

http://www.cisco.com/en/US/products/index.html

Networking Professionals Connection is an interactive website for networking professionals to share

questions, suggestions, and information about networking products and technologies with Cisco

experts and other networking professionals. Join a discussion at this URL:

http://www.cisco.com/discuss/networking

•

World-class networking training is available from Cisco. You can view current offerings at

this URL:

http://www.cisco.com/en/US/learning/index.html

Cisco MGX 8800/8900 Series Hardware Installation Guide

Releases 2 - 5.2, Part Number OL-4545-01, Rev. H0, May 2006

Obtaining Additional Publications and Information

Cisco MGX 8800/8900 Series Hardware Installation Guide

Releases 2 - 5.2, Part Number OL-4545-01, Rev. H0, May 2006

lvi

Hanns G HSG1040 User Manual
GE Monogram ZGU385L User Manual
GE JGP337 User Manual
Frigidaire FFEC3024LB User Manual
Electrolux SG 414 User Manual
Eizo EIZO FlexScan L661 User Manual
Diamond Multimedia SKU 4350PE512HS User Manual
Diamond Multimedia BizView BV200 PCI User Manual
Blodgett CN14E User Manual
Belkin WIRELESS P74775UK User Manual