USER GUIDE
3-PORT FIREWIRE® PCI CARD
Model: 29970
INTRODUCTION
Thank you for purchasing the 3-Port FireWire PCI Card. This product conveniently adds three 400 Mbps 6-
pin ports to your PC or Mac desktop computer with this easy-to-use FireWire PCI controller card. This 32-
bit card is fully hot-swappable and daisy-chainable up to 63 devices in peer-to-peer configuration. Plug-
and-play so you can download and edit your digital video (DV) for cameras/camcorders; or use with hard
disks, scanners, set-top boxes and other high-tech appliances. We recommend that you read this
manual thoroughly and retain for future reference.
2
FEATURES
™ Supports 100/200/400 Mbps transfer rate
™ Compliant to IEEE 1394-1995 and 1394a supplement
™ 32-bit PCI Card compliant
™ Supports up to 63 devices in peer-to-peer configuration
™ Compliant with Open Host Controller Interface (OHCI) 1.0 specification
3
SYSTEM REQUIREMENTS
™ Windows® 98SE/Me/2000/XP/Vista/7 and Mac® OS 10.X.X or higher
4
PACKAGE CONTENTS
™ (1) 3-Port FireWire PCI Card
™ User Manual
5
DEVICE INSTALLATION
This section will explain how to install the FireWire card into your computer.
Step 1
Power off the computer, then disconnect the power cord.
Step 2
Remove each screw found on the back of the computer and remove the shell from the computer.
Step 3
With the power cord disconnected from your computer, you can touch the metal part of the case to ground
yourself. This will discharge any static electricity which can damage your computer.
Step 4
Locate an available PCI slot. This will be in the area of your computer where other cards that look similar
to this one are installed.
Step 5
Visually confirm that the Firewire 1394 port will fit into the available slot you have chosen.
6
DEVICE INSTALLATION
Step 6
If necessary, remove the knockout on the back of the computer which corresponds to the PCI slot you
have confirmed as your selection. If there is a screw, place it in a safe spot as you will be using it to
attach the FireWire 1394 Port.
Step 7
Push the FireWire 1394 Port card firmly into the PCI slot. Apply pressure as needed until the edge
connector is completely sealed.
Step 8
Once the FireWire 1394 is fully seated, the gold edge connectors are completely in the slot.
Step 9
Mount the 1394 Port in place with a screw. Make sure the screw is firmly tightened so the 1394 Port does
not slide out of its seated position.
Step 10
Replace the computes shell and screw it in place.
Step 11
Now that your FireWire 1394 card is installed and the shell is in place, you can safely connect the power
cable.
7
DRIVER INSTALLATION-WINDOWS 98SE/ME/WINDOWS 2000
When you initially connect your FireWire 1394 card, Windows will automatically detect you have a new
device the first time you power on your computer and thus request the device software drivers. Please
follow the step-by-step instructions below to install the drivers.
Step 1
At the Add New Hardware Wizard, click on “Next”
Step 2
Select the option “Search for the best driver for your devices (Recommend)”, and click on “Next”.
Step 3
Select the option “CD-ROM driver” then click on “Next”.
8
DRIVER INSTALLATION-WINDOWS 98SE/ME/WINDOWS 2000
Step 4
Click “Next” and then “Finish” respectively.
Step 5
Reboot your computer for setup to take effect.
Verify Installation
From the main desktop, click on My Computer, then double-click on Control PanelÆ SystemÆ Device
Manager and you will see the FireWire card listed in the device list.
9
DRIVER INSTALLATION-WINDOWS XP
Step 1
At the Add New Hardware Wizard, click on “Next”
Step 2
Select the option “Search for the best driver for your devices (Recommend)”, and click on “Next”
Step 3
Select the option “Specify the location”, and type in C: then click on “Next”
Step 4
Click “Next” and then “Finish” respectively.
Step 5
Select “Yes” to reboot the computer for the setup to take effect
10
DRIVER INSTALLATION-WINDOWS XP
Verify Installation
From the main desktop, click on “My Compute”, and then double-click on “Control Panel”,
“System”, and “Device Manager”.
11
DRIVER INSTALLATION-WINDOWS VISTA/ WINDOWS 7
Step 1
Start power to run Windows Vista or Windows 7
Step 2
Windows will automatically detect you have a new device the first time you power on your PC and thus
request the devices software drivers.
Step 3
Detect you have device to Install device software
12
DRIVER INSTALLATION-WINDOWS VISTA/ WINDOWS 7
Step 4
Install the driver “VIA OHCI Compliant IEEE 1394 Host ontroller”
Step 5
Check “Device Manager” to “IEEE 1394 Bus host controllers” and the “VIA OHCI Compliant IEEE
1394 Host Controller”
13
TROUBLESHOOTING
If after installing the drive and loading the software and you find that the PCI 1394 card is not functional,
try these suggestions first.
• Are ports active on the card conflicting with equivalent ports in the computer?
• Is the card inserted snugly into the slot on the main board?
14
CABLES TO GO™ ONE YEAR WARRANTY
At Cables To Go, we want you to be totally confident in your purchase. That is why we offer a one year
warranty on this device. If you experience problems due to workmanship or material defect for the duration
of this warranty, we will repair or replace this device. To request a Return Merchandise Authorization
Cables To Go
3555 Kettering Blvd.
Moraine, OH 45439
1-800-506-9607
©2010. Cables To Go. Microsoft , XP, and Vista are either registered trademarks or trademarks of Microsoft Corporation in
the United States and/or other countries. Mac is either a registered trademark or trademark of Apple. This product is not
endorsed or manufactured by Microsoft Corporation or Apple.
15
16
For more information on this product or to check for updated drivers,
manuals or frequently asked questions please visit our website.
VER. 1.0.3.22.10
|