SV500 Pyrolytic Oven
Manual for Installation, Use and Maintenance
Customer Care Department • The
Group Ltd. • Harby Road • Langar • Nottinghamshire • NG13 9HY
Important
Read the user instructions carefully before using the oven for the first time.
Clean the oven regularly.
Remove spills as soon as they occur.
Always use oven gloves when removing shelves and trays from the ovens.
Do not allow children near the oven when in use.
Do not lean on the oven door, or place heavy items on the door. Make sure that children do not climb or sit on the door when
it is open.
Do not pull the oven by the handle.
Do not allow fat or oils to build up on the oven shelves, grill pan or oven base.
Do not place any cooking utensils or plates directly on the oven base.
Cook on all functions with the oven door closed.
Do not grill food containing fat without using the grill pan grid.
Do not cover the grill pan grid or the oven walls with aluminium foil.
Do not use the oven tray for roasting.
Do not perform maintenance or cleaning of the oven without first switching off the electricity supply. If the oven has recently
been used, allow to cool.
Do not use steam cleaners to clean the oven.
Do not place hot enamel parts in water. Leave them to cool first.
Do not allow vinegar, coffee, milk, saltwater, lemon or tomato juice to remain in contact with enamel parts.
Do not use abrasive cleaners or powders that will scratch the surface of the enamel.
Do not attempt to repair the internal workings of your oven.
The oven can require increased ventilation on pyrolytic programmes. This can be achieved either from an open window or the
use of a fan.
The oven is equipped with a cooling fan which will continue to run after the cooking programme has ended.
First use of the oven
Before using the oven for the first time we recommend that you clean the oven with soapy water, rinse carefully and then heat
on the fan oven function for 15 minutes at 220. A slightly unpleasant smell may be produced, caused by grease remaining on the
oven elements from the production process.
Using the touch control
The touch controls should be used with the flat of your finger, rather than the fingertip.
2
Using your oven
A
B
C
D
E
Fig.2
A
B
Display
Temperature Control Knob
Function Control Knob
Oven Light
C
D
E
Shelf supports
3
The Control Panel and Display
A
B
C
D
E
F
I
H
G
Fig.3
A
B
C
D
E
Clock display
Door lock indicator
Eco cooking indicator
Minute minder indicator
End time indicator
Cooking time indicator
Time setting keys
F
G
H
I
Timer selection key
Temperature display
4
Fitting Out Your Appliance
1. Side racks (E on fig. 4)
The side racks allow five different cooking heights for the drip
tray and shelf.
When cooking using the grill functions and rotisserie, use the
drip tray or shelf at height 5 to collect the juices from the food.
2. Drip tray (figure 4)
Fig. 4
The enamel drip tray can be used for baking cakes or placed
underneath the shelf to collect the juices from grilling. Avoid
placing roasts or meats directly in the drip tray, as this will cause
significant splattering on the oven walls. Do not put the drip
tray on the base of the oven except on the grill functions.
REAR
3. Anti-tilt shelf (figure 5)
The metal shelf can be used to hold all dishes and baking trays.
It can also be used over the drip tray for barbecuing in the oven.
FRONT
Fig. 5
4. Dish (figure 6)
This can be used as a cooking dish, half-filled with water as a
bain-marie/double boiler, or as an alternate to the enamel drip
tray. Avoid placing roasts or meats directly in the drip tray, as
this will cause significant splattering on the oven walls. Do not
put the drip tray on the base of the oven except on the grill
functions.
Fig. 6
5. Rotisserie
The rotisserie roasts meat evenly within the oven, cooking the
food in its juices as it rotates.
To use the rotisserie:
1. Insert the dish at shelf level one or on the base of the oven
to collect the juices from the meat
2. Slide one clip onto the rotisserie. Place the joint onto the
centre of the rotisserie, then slide the second clip onto the
rotisserie. Slide both clips into the joint and then tighten
them to hold the joint in place.
Fig. 7
3. Put the rotisserie onto the frame.
4. Gently slide the frame onto the middle shelf level of the
oven ensuring the pointed end of the rotisserie is fully
inserted into the niche at the back of the oven.
5. Unscrew and remove the handle. After cooking, screw the
handle back onto the rotisserie so you can remove the joint
without any risk of injury.
Please note: The clips on the are sharp – take carewhen
using the rotisserie.
5
General Settings and Use
Clock
To set the clock when the time and the clock indicator are flashing (for example, when the oven is first switched on) touch
or until the correct time shows on the display, then touch to confirm the selection. The oven will beep to confirm
the selection and the clock and clock indicator will stop flashing.
To set the clock once the time has been set (when the clock is not flashing) touch and hold
for three seconds until the
clock and the clock indicator flashes. Touch or until the correct time shows on the display, then touch to confirm
the selection. The oven will beep to confirm the selection and the clock and clock indicator will stop flashing.
Please note: the clock will set automatically if no key is touched for eight seconds.
Minute minder
This oven is equipped with a minute minder to count down for a maximum of 60 minutes. To set the timer, touch so the
display flashes 0:00 and the minute minder indicator flashes. Touch or until the required time shows on the display.
The minute minder will set after eight seconds delay and starting counting down. To start the minute minder immediately,
touch
.
The display will show the time remaining and the minute minder indicator will stay lit. At the end of the countdown, the
minute minder indicator will flash and the oven will beep intermittently for approximately 2 minutes. To stop the end of
timer alerts before that time, touch any key.
To check on the progress of the minute minder during cooking, touch until the minute minder indicator flashes and the
time remaining will show on the display.
To cancel the minute minder touch until the minute minder indicator flashes and then touch or until the display
shows 0:00.
General Settings and Use
Display brightness adjustment
Set the clock to 00:10.
Touch and
Touch or
together for 10 seconds until the display shows –CO–.
until the required brightness shows on the screen.
After eight seconds delay, the oven will confirm the setting. Then set the clock to the correct time of day.
6
General Settings and Use
To programme the oven
Turn the function control knob to the required programme.
The display will flash the temperature preset for the programme (as detailed on page 8) and start cooking immediately.
To change the temperature, turn the temperature control knob until the required temperature shows on display. The
temperature will flash on the display whilst the oven heats up. Once the oven has reached the required temperature, the
oven will beep three times and the temperature display will stop flashing.
To set the cooking time (the cooking starts immediately, and finishes at a programmed time to a maximum of 9 hours
59 minutes), touch once so the cooking time indicator flashes and the display shows 0:00. Then touch or until
the required cooking time (in minutes) shows on the display and after eight seconds delay the oven will confirm the
programme. The cooking time indicator will stay lit and the cooking time will show on the display.
To set a delayed programme (the cooking starts and finishes at a programmed time up to 23 hours 59 minutes), first set
the cooking time as above, then immediately touch so the end time indicator flashes and the display flashes the time
the programme is due to end (current time + cooking time). Then touch or
until the required end time shows on the
display, and after eight seconds delay the oven will confirm the programme. The cooking and end time indicators will stay
lit, the current time will show on the display and the oven light will switch off. When the programme starts cooking, the
end time indicator will switch off, the cooking time will show on the display and the oven light will switch back on.
To cancel a programme, touch once so the cooking time indicator flashes, then touch
until the display shows 0:00.
At the end of the programme, the oven will beep intermittently for approximately two minutes, and the cooking time
indicator will flash. To stop the beep, touch any of the keys.
Please note: The function control knob must be turned to 0 to switch off the oven completely after a
programme is finished, and before any new cooking can start.
If the oven must be preheated, switch on the oven as above. Once the preheat is complete, the upper bars on the
temperature indicator on the display will stay lit and the oven will beep three times, pause, and beep three times again.
7
General Settings and Use
Oven functions
Each of the oven functions uses different elements within the oven to offer you the best choice of cooking every time.
The cooking functions are explained below. The pyrolytic functions are explained on page xxx.
1. Fan Oven – preset 180 (range available 35-235)
Using the fan element and the fan, this cooking function blows the hot air into and around the oven cavity.
Temperatures are achieved quicker, reducing or even removing the need for preheating.
Both cooking temperatures and cooking times can be reduced for a more energy efficient cooking
programme.
Perfect for cooking white meat, fish and vegetables moist.
2. Conventional Oven – preset 240 (range available 35-275)
This function uses the top and bottom heating elements only.
Natural convection creates a perfect cooking zone in the centre of the oven, ideal for dark fruit cakes and
pastries.
Preheating is recommended with the conventional oven function.
3. Fanned Grill – preset 200 (range available 180-230)
This function uses the fan to circulate the heat from the grill element around the food.
This function can be used in conjuction with the rotisserie, which will turn until the door is opened. When the
rotisserie is used, put the drip tray on the lowest shelf level.
Foods cook quickly on both sides without the need for turning or preheating the oven.
This function is recommended for all roast meats, and to retain the moist texture of fish steaks.
4. Conventional Eco Oven – preset 200 (range available 35-275)
This function uses the top and bottom heating elements only, saving approximately 25% of the energy whilst
maintaining the cooking performance.
Natural convection creates a perfect cooking zone in the centre of the oven, ideal for dark fruit cakes and
pastries.
Preheating is recommended with the conventional eco oven function.
Please note: cooking time may be slower as a result of the energy savings gained.
This function is used to obtain the results indicated on the energy label in compliance with European standard
EN 50304 and in accordance with European Directive 2002/40/CE.
5. Fan With Lower Heat – preset 205 (range available 35-275)
This function circulates the heat produced by the bottom element, with a small amount of heat from the grill
and the fan.
The shelf should be on the lowest shelf support setting.
This function is recommended for quiches, fruit tarts etc to cook the crust thoroughly. This function is also
recommended for dishes that rise (e.g. cakes and soufflés) where a crust on the top is not required.
6. Low temperature cooking– preset 80 (range available 35-100)
Using the fan and a limited amount of heat, this oven function circulates the air around the oven cavity,
allowing for dough proving, plate heating and defrosting.
Meats should be placed on a dish to catch liquids from the defrosting process. These liquids are not edible.
8
General Settings and Use
7. Full Grill – preset 275 (range available 180-275)
The grill function radiates the heat from the grill element.
The fully temperature variable grill is ideal for grilling anything up to a full family meal (full grill)
This function can be used in conjuction with the rotisserie, which will turn until the door is opened. When the
rotisserie is used, put the drip tray on the lowest shelf level.
FOR EACH GRILL FUNCTION, PLEASE NOTE:
• Always grill with the oven door closed.
• Put the grill pan as close to the grill as possible.
• You are recommended not to grill for more than 30 minutes at a time.
• Preheat the grill for approximately five minutes with the oven door closed.
9
Pyrolysis Programmes
This oven can clean itself by a process known as pyrolysis, heating the cavity to a temperature of 500C. This will burn off
the residue from spattering and spillages caused by cooking.
Pyrolytic programmes should be used when the oven smokes during preheating or cooking or if the oven smells even when
cold. It is not necessary to run a pyrolytic programme after every use of the oven, as shown in the table below. Do not wait
until the oven is coated in grease to run a pyrolytic programme.
Amount of residue
Light
Type of food cooked
Biscuits, vegetables, pastry
Meats, fish, stuffed vegetables
Joints of meat on the rotisserie
Frequency of pyrolysis
Not required
Medium
Every three uses.
Heavy
After each use if there was extensive splattering
The smoke produced by pyrolysis is broken down by passing through a catalyser.
This oven has 2 pyrolytic programmes:
Pyrolysis – 2 hour programme
Pyrolysis Eco – 1 hour 30 minute programme.
Turn the function control knob to the required programme.
The programme begins immediately. The display stops flashing and the temperature symbol lights up. Once the oven
reaches temperature, the door locks shut and is shown on the display to indicate the door is locked.
At the end of the programme, the timer display flashes 0:00. The oven door will be locked for up to 30 minutes until the
end of the cooling time.
Turn the function control knob to 0.
When the oven is cool, use a damp cloth to remove the white ashes. The oven is ready for use.
Both programmes can be run immediately or as a delayed programme by setting the end time as with normal cooking.
Please note: Before any pyrolytic programme, remove all shelves, trays and other accessories from the oven
and clean up any major spills to avoid the risk of fire or excessive smoke.
Do not hang towels or cloths on the oven handle during pyrolysis.
10
Cleaning and Maintenance
IMPORTANT:
Always disconnect the appliance from the power supply before undertaking any cleaning or maintenance.
You should always allow the oven to cool fully after use before undertaking any cleaning or maintenance.
You should only use non-abrasive cleaners. Any abrasive cleaners (including Cif) will scratch the surface and could erase
the control panel markings. You should not cleaning products with a chlorine or acidic base.
Any spillages should be cleaned off immediately, especially any alkaline or acidic substances (lemon juice, vinegar etc.)
Stainless steel
Stainless steel can be effectively cleaned by simply using a dilute solution of water and mild detergent and drying to a shine
with a clean cloth. Proprietary stainless steel cleaners are available. We recommend the CDA E-Cloth available from the
CDA Sales Team for cleaning stainless steel surfaces.
Enamelled parts
All enamelled parts must be cleaned with a sponge and soapy water only, or other non-abrasive products. Suitable
proprietary chemical cleaners may be used after first consulting with the manufacturer’s recommendations and testing a
small sample on the oven cavity.
PLEASE NOTE: Steam cleaners must not be used to clean this appliance.
Do not store flammable material in the oven.
When correctly installed, your product meets all safety requirements laid down for this type of product.
However, special care should be taken around the rear or the underneath of the appliance as these areas are
not designed or intended to be touched and may contain sharp or rough edges that could cause injury.
11
Changing the Oven Lamp
Before any maintenance is started involving electrical
parts, the oven must be disconnected from the power
supply.
Bulb
If the oven has been in use, let the oven cavity and the
heating elements cool down before attempting any
maintenance.
Never replace the bulb with bare hands as contamination
from your fingers can cause premature failure. Always
use a clean cloth or gloves.
Unscrew
Fig. 8
Protective cover
Changing the bulb
Unscrew the protective cover.
Carefully remove the bulb and replace with a new one suitable
for high temperatures with the same specification as the
original bulb.
Refit the protective cover.
WRONG
WRONG
CORRECT
Fig. 9
12
Care and Maintenance
Cleaning the interior of the door
Open the door completely and insert two of the red stoppers
supplied with the oven, as shown in figure 10.
Then insert the other two red stoppers in the A slots, as shown
in figure 11.
Lever the stoppers to lift the frame and the glass from the door,
as shown in figure 12.
Fig. 10
Remove the inner frame and the panes of glass as shown
in figure 13, ensuring you put them on a soft flat surface to
prevent damage.
A
Fig. 11
Fig. 12
Fig. 13
13
Care and Maintenance
Clean the panes of glass using a soft sponge and washing up
liquid.
Do not soak the glass in water.
Do note use abrasive cleaning products, metallic scrapers or
scouring sponges. These could scuff the surface and cause the
glass to shatter.
Rinse with clean water and dry off with a lint-free cloth.
Fig. 14
The inner glass assembly can be removed for cleaning if
necessary. Each pane of glass has a black corner pad which
much be replaced in their original position, as shown in fig. 16.
Replace the inner glass assembly in the door so that L and R and
located on the hinge side.
Replace the inner glass so that PYROLYSIS faces you.
Replace the clean panes in the door, taking care to slot the
frame under the spigot next to the hinge, as shown in figure 14.
Reattach the frame by tightening it against the door until the
frame clicks into place.
Do not push down on the door itself as this may damage your
oven.
Fig. 15
Finally remove the red stoppers from the hinge slots.
L
R
Fig. 16
CLAC
CLAC
Fig. 17
14
Troubleshooting
If the oven is not functioning correctly, check the advice below prior to calling CDA Customer Care.
Problem
Possible Cause
Advice
Check the oven is switched on at the
cooker point and the fuse/circuit
breaker has not activated.
The oven does not heat up
There is no power supply to the oven
The padlock on the display is flashing
The oven light is not working
Door lock system fault
Light fault
Call CDA Customer Care
Replace the bulb
The pyrolysis programmes do not start
The door is not properly closed
Door lock system fault
Close the door completely
Call CDA Customer Care
The oven is at the required temperature
The oven starts beeping during cooking
The oven starts beeping at the end of
the cooking programme
The programme has finished
The oven display will show error codes if there is a fault with the appliance. These are detailed below. Before calling CDA
Customer Care, take note of the error code as this will help when attempting to resolve the problem.
Error Code
F01
Fault
Temperature sensor error
F02
Overheated oven . First ensure there is adequate ventilation to the oven as described on page 16.
F03
Pyrolysis failure (door locked)
Door interlock
F04
F05
Other cooking fault
F10
Information only – power cut during cooking
Auto stop. The oven is equipped with an auto stop function to automatically switch off the oven if it is in
continuous use for more than 23 hours and 30 minutes.
AUTO
15
Installation
Important
If the oven is being installed into a built under oven housing unit ensure that the front rail at the top of the unit is not
installed as it could restrict ventilation.
Ensure that air can flow freely around the housing area. If the oven is being installed into a fully enclosed built-under oven
housing unit it may be necessary to cut a small slot in the top of the plinth fitted under the unit. Cut a section 400mm
wide and a minimum of 15mm high to allow air to pass under the unit. Alternatively cut a section 400 x450mm in the base
of the carcass as indicated.
Failure to allow adequate ventilation to the appliance may result in overheating or damage to adjacent units and could
invalidate the warranty.
The walls of the kitchen units must be able to withstand temperatures of 75℃ above ambient (typically this is between
90℃ and 100℃). This appliance is type X installation.
When correctly installed ensure that there is a gap of 6mm minimum between the sides of the oven and adjacent
furniture doors.
Lift the oven carefully into position on the shelf, taking care NOT to lift it by the door handle. If you open the oven door,
you will see 2 screw holes, 1 on each side of the oven. The oven should then be secured to the housing by fitting screws
into these holes. Remember the housing should not be free standing but be secured to the wall and/or adjacent fittings.
How to install your oven
You will need the following housing area fit your oven correctly.
560
Dimensions
Height (mm)
Width (mm)
Depth (mm)
Oven
594
Housing
585
550
585
592
560
561
550 (min)
The oven is designed to fit into a cabinet of 600mm width. The
oven can be built in or built under the kitchen units, but you
must ensure that it is properly ventilated. In the diagram the
built-in oven is ventilated by means of a space at the top of the
kitchen cabinet. There are many other methods of ventilating
your oven - Consult a qualified engineer for advice.
70
550
fig. 18
16
Mains Electricity Connection
Warning! This appliance must be earthed
We recommend that the appliance is connected by a qualified electrician, who is a member
of the N.I.C.E.I.C. and who will comply with the I.E.E. and local regulations.
This appliance is intended to be connected to fixed wiring and is not suitable for
connection to a 13A plug or 13A supply.
This appliance is intended to be connected to fixed wiring by a double pole switch, having
a contact separation of at least 3mm in all poles. The switch must be positioned no further
than 2m from the appliance.
This appliance is supplied with a 3 core mains cable; the wires are in accordance with the
following code:
Green and Yellow = Earth
Green/yellow
Blue = Neutral
Blue
Brown = Live
Brown
N L
Fig. 19
Please note:
•
The mains cable must only be replaced by a qualified electrician or service engineer
and must be of equivalent or better rating (i.e. 1.5mm2, HO5V2V2-F HO5RR-F,
HO5RN-F).
•
The marking of the current rating of the fuse or circuit breaker protecting this appliance
should be marked on the socket outlet (16A).
•
Assembly and electrical connection should be carried out by specialised personnel.
•
•
When installing this product we recommend you seek the help of another individual.
The mains isolation switch must be accessible after installation.
17
18
To contact our Customer Care Department, or for Service,
please contact us on the details below.
Customer Care Department • The
Group Ltd. • Harby Road • Langar • Nottinghamshire • NG13 9HY
|