RC 9021 .. - Dual Fuel Cookers
Manual for Installation, Use and Maintenance
GB
Customer Care Department • The
Group Ltd. • Harby Road • Langar • Nottinghamshire • NG13 9HY
3
Features and Technical Data
Gas Burners
1. Auxiliary burner (A)
1.00 kW
2. Semi-Rapid burner (SR) 1.75 kW
3. Semi-Rapid burner (SR) 1.75 kW
4. Rapid burner (R)
5. Triple Ring burner (TR)
3.00 kW
3.50 kW
Note:
The electric ignition is incorporated in the knobs.
The appliance has a safety valve system fitted, the flow of gas will be stopped if and when the flame should
accidentally go out.
3
5
4
1
2
Conventional
oven
Multifunction
main oven
Fig. 1
4
Control Panel
Controls Description
1. Front right burner control knob
2. Rear right burner control knob
3. Central burner control knob
4. Rear left burner control knob
5. Front left burner control knob
6. Multifunction main oven switch knob
7. Multifunction main oven thermostat knob
8. Electronic programmer (main oven only)
9. Conventional oven thermostat knob
10. Conventional oven switch knob
Pilot Lamps:
11. Main oven thermostat indicator light
12. Conventional oven thermostat indicator light
Please note: This appliance incorporates a safety cooling fan which you will hear operating whenever
the oven or grill are in use. The cooling fan may also operate when the oven is switched off. This fan is to
reduce the external temperature of the appliance and cool the internal components.
12
11
A
U
T
O
Fig. 2
8
7
6
5
4
3
2
1
10
9
5
Electronic Programmer (Main Oven Only)
The electronic programmer is a device that groups together the following functions:
– 24 hour clock with illuminated display
– Timer (up to 23 hours and 59 minutes)
– Programme for automatic oven cooking
– Programme for semi-automatic oven cooking.
Description of the illuminated symbols:
Description of the buttons:
Symbols Description
Symbols
Description
Programmer in automatic position
but not programmed.
AUTO
flashing
Timer
Programmer in automatic position
with program set.
AUTO
always lit
Cooking time
End of cooking time
Automatic cooking taking place.
Timer in operation
Manual position and cancellation of
the set cooking program
To increase the numbers on the
digital display
Program error.
and
AUTO
flashing
(The time of day lies between the
calculated cooking start and end
time).
To decrease the numbers on the
digital display.
Note:
Select a function by the respective button and, in 5 seconds, set the required time with the
(“one-hand” operation).
/
buttons
After a power cut the display resets to zero and cancels the set programs.
A
U
T
O
Fig. 3
Fig. 4
6
Electronic Clock (fig. 4)
The programmer is equipped with an electronic clock with illuminated numbers which indicates hours
and minutes. Upon immediate connection of the oven or after a power cut, three zeros will flash on the
programmer display.
To set the correct time of day it is necessary to push the
you have set the correct time. In another way push simultaneously the
time push the or button.
button and then the
or
button until
two buttons and at the same
Note: If the clock is reset it deletes any previously set programs.
Normal Cooking without the Use of the Programmer
To manually use the oven, that is, without the aid of the programmer, it is necessary to cancel the flashing
AUTO by pushing the button (AUTO will be switched off and the symbol will go on - Fig. 5).
Attention: If the AUTO is steadily lit (which means a cooking program has already been set), the program
can be cancelled and switched to manual by pushing the button
If the oven is switched on, you must switch off manually.
.
Electronic Timer
The timer program consists only of a buzzer which may be set for a maximum period of 23 hours and 59
minutes. If the AUTO is flashing push the
To set the time, push the button and the
button.
or
until you obtain the desired time in the panel
(fig. 6). Having finished the setting, the clock hour will appear on the panel and the
illuminated.
symbol will be
The countdown will start immediately and may be seen at any moment on the panel by simply pressing
the button
At the end of the time, the
.
symbol will disappear and the buzzer will sound and continue for
approximately 7 minutes or until a button is pressed (not the
After a short time the display will revert back to the time of day.
/
buttons).
Setting the Frequency of the Audible Signal
The buzzer has 3 different tones and can be changed by pressing the
of day is displayed.
button, but only when the time
Fig. 5
Fig. 6
7
Automatic Oven Cooking
To cook food automatically in the oven, it is necessary to:
1. Set the length of the cooking time
2. Set the end of the cooking time
3. Set the temperature and the oven cooking program.
These operations are done in the following way:
1. Set the length of the cooking period by pushing the
decrease if you have passed the desired time (fig. 7). The AUTO and the
button and the
button to increase, or
symbol will illuminate.
to
2. Set the end of the cooking time by pressing the
button (the cooking time already added to the clock
time will appear), and the
the button.
After this setting, the
button (fig. 8); if you pass the desired time you may get back by pushing
symbol will disappear. If after this setting, the AUTO flashes on the display
and a buzzer sounds, it means there was an error in the programming, that is that the cooking cycle has
been superimposed on the clock. In this case, modify the end of cooking time or the cooking period
itself by following again the above mentioned instructions.
3. Set the temperature and the cooking program by using the switch and thermostat knobs of the oven
(see specific chapters).
Now the oven is programmed and everything will work automatically, that is the oven will turn on at the
right moment to end the cooking at the established hour.
During cooking, the
symbol remains illuminated.
By pushing the button you can see the time that remains until the end of cooking.
The cooking program may be cancelled at any time by pushing
.
At the end of the cooking time the oven will turn off automatically, the
symbol will turn off, AUTO
will flash and a buzzer will be sound, which can be turned off by pushing any of the buttons except the
buttons.
/
Turn the switch and thermostat knobs to zero and put the programmer onto “manual” by pressing the
button.
Attention: After a power cut the clock resets to zero and cancels the set programs. After a power cut,
three zeros will flash on the display.
A
U
T
A
U
T
O
O
Fig. 7
Fig. 8
8
Semi - Automatic Cooking
This is used to switch the oven off automatically after the desired cooking time has elapsed.
There are two ways to set the semi-automatic cooking function:
1. Set the length of time you need to cook the food by pushing the
advance, or to go backwards (Fig. 9).
This sets the desired “stop” time.
button and the
button to
button to
AUTO and the
symbol will be on.
or
2. Set the time you need the food to stop cooking by pushing the
button and the
advance, or
AUTO and the
to go backwards if you have passed the desired time (Fig. 10).
symbol will be on.
Then set the temperature and the cooking program (see the relevant sections).
The oven is switched on and it will switch off automatically at the end of the desired time.
During cooking, the
symbol remains on and by pressing the button
you can see the time that
remains until the end of the cooking.
The cooking program can be cancelled at any moment by pushing the
button.
At the end of the cooking period, the oven and the symbol will disappear, AUTO will flash and a buzzer
will sound and can be stopped by pushing any of the buttons except the buttons.
/
Turn the function selector switch and thermostat knobs to zero and put the programmer onto “manual”
by pressing the button.
Attention: After a power cut the clock resets to zero and cancels the set programs. After a power cut,
three zeros will flash on the display.
A
U
T
A
U
T
O
O
Fig. 9
Fig. 10
9
How to Use the Hob Burners
Hob Burners
Each hob burner is controlled by a separate gas valve operated
by a control knob (fig. 11) which has 3 positions marked on the
control panel, these are:
– Symbol
: Tap closed (burner off)
– Symbol
– Symbol
: High (maximum)
: Low (minimum)
Push in and turn the knob anti-clockwise to the selected
position.
The maximum aperture position permits rapid boiling of liquids,
whereas the minimum aperture position allows slower warming
of food or maintaining boiling conditions of liquids.
To reduce the gas flow to minimum, rotate the knob further anti-
clockwise to point the indicator towards the small flame symbol.
Other intermediate operating adjustments can be achieved by
positioning the indicator between the maximum and minimum
aperture positions, not between the maximum aperture and
closed positions.
Fig. 11
Note: When the hob is not being used, set the gas knobs to their closed positions and also
close the cock valve on the gas bottle or the main gas supply line.
Lighting of the Hob Burners
To ignite the burner, the following instructions are to be followed:
1 - Press in the corresponding knob and turn counter-clockwise to the full flame position marked by the
symbol (fig. 11) and hold the knob in until the flame has been lit.
In the case of a mains failure light the burner with a match or lighted taper.
2 - Wait about ten seconds after the gas lighting before releasing the knob (starting time for the valve).
3 - Adjust the gas valve to the desired power.
Important
If the burner flame should go out for some reason, the safety valve will automatically stop the gas flow.
To re-light the burner, return the knob to the closed position, wait for at least 1 minute and then
repeat the lighting procedure.
If your local gas supply makes it difficult to light the burner with the knob set to maximum, set the knob
to minimum and repeat the operation.
10
Choice of Burner
The burner must be choosen according to the diameter of the
pans and energy required. Saucepans with handles which are
excessively heavy, in relationship to the weight of the pan, are
safer as they are less likely to tip. Pans which are positioned
centrally on burners are more stable than those which are offset.
It is far safer to position the pan handles in such a way that they
cannot be accidentally knocked.
Fig. 12
When deep fat frying fill the pan only one third full of oil.
DO NOT cover the pan with a lid and DO NOT leave the pan unattended.
In the unfortunate event of a fire, leave the pan where it is and turn off all controls. Place a damp cloth or
correct fitting lid over the pan to smother the flames.
DO NOT use water on the fire.
Leave the pan to cool for at least 30 minutes.
Do not use pans with concave or convex bases
Burner Size
Auxiliary
Semi-Rapid
Rapid
Minimum Pan Diameter (cm)
Maximum Pan Diameter (cm)
12
16
24
26
-
14
24
26
28
36
Triple Ring
Wok
Correct Use of Triple-Ring Burner
The flat-bottomed pans are to be placed directly onto the pan-support.
To use the WOK you need to place the proper stand in order to avoid any faulty operation of the triple-
ring burner (Figs. 13 - 14).
Important: The wok pan stand (fig. 14) MUST BE PLACED ONLY over the pan-rest for the triple-ring
burner.
WRONG
CORRECT
Fig. 13
Fig. 14
11
How to Use the Multifunction Main Oven
General Features
Attention:
The oven door
becomes very hot
during operation.
As its name indicates, this is an oven that presents particular features from
an operational point of view.
In fact, it is possible to insert 7 different programmes to satisfy every
cooking need.
The 7 positions, thermostatically controlled, are obtained by 4 heating
elements which are:
– Bottom element
– Top element
– Grill element
1200 W
1000 W
2000 W
2200 W
– Circular element
Note:
Upon first use, it is advisable to operate the oven for 30 minutes in the position
and for another 30
minutes at the maximum temperature (thermostat knob on position 250) in the positions
eliminate possible traces of grease on the heating elements.
and
, to
Clean the oven and accessories with warm water and washing-up liquid.
WARNING:
The door is hot, use the handle.
ATTENTION - MOST IMPORTANT
Pay special attention not to touch the hot heating element
inside the oven cavity.
Operating Principles
Heating and cooking in the MULTI-FUNCTION oven are obtained in the following ways:
a. by normal convection
The heat is produced by the upper and lower heating elements.
b. by forced convection
A fan sucks in the air contained in the oven muffle, which sends it through the circular heating element
and then sends it back through the muffle. Before the hot air is sucked back again by the fan to repeat
the described cycle, it envelops the food in the oven, provoking a complete and rapid cooking.
It is possible to cook several dishes simultaneously.
c. by semi-forced convection
The heat produced by the upper and lower heating elements is distributed throughout the oven by the
fan.
d. by radiation
The heat is radiated by the infra red grill element.
e. by radiation and ventilation
The irradiated heat from the infra red grill element is distributed throughout the oven by the fan.
f. by ventilation
The food is defrosted by using the fan only function without heat.
12
Thermostat Knob (fig. 15)
This only sets the cooking temperature and does not switch the oven on.
Rotate clockwise until the required temperature is reached (from 50 to 250°C).
The light between the thermostat and the function selector will illuminate when the oven is switched on
and turns off when the oven reaches the correct temperature.
The light will cycle on and off during cooking in line with the oven temperature.
Fig. 15
Fig. 16
Function Selector knob (fig. 16)
Rotate the knob clockwise to set the oven for one of the following functions.
Oven Light
By setting the knob to this position, only the oven light comes on.
It remains on in all the cooking modes.
Traditional Convection Cooking
The upper and lower heating elements come on. The heat is dispersed by natural convection and the
temperature must be set to between 50° and 250°C via the thermostat knob.
The oven must be preheated before cooking.
Recommended for:
Food that requires the same degree of cooking both inside and out, for example roasts, spare pork ribs,
meringues etc.
13
Grilling
The infrared grill element comes on. The heat is dispersed by radiation.
Use with the oven door closed and the thermostat knob to position 225°C for max 15 minutes, then
to position 175°C.
For cooking hints, see the chapter “USE OF THE GRILL”.
Recommended for:
Intense grilling, browning, cooking au gratin and toasting etc.
It is recommended that you do not grill for longer than 30 minutes at any one time.
Caution: the oven door becomes very hot during operation. Keep children well out of reach.
Defrosting Frozen Foods
Only the oven fan comes on. Use with the thermostat knob set to “ ” - other positions have no effect.
The food is thawed by ventilation without heating.
Recommended for:
Quick thawing of frozen foods; one kg requires approximately 1 hour.
Thawing times vary according to the quantity and type of food to be thawed.
Hot Air Cooking
The circular element and fan come on. The heat is dispersed by forced convection and the temperature can
be regulated to between 50° and 250°C via the thermostat knob. The oven does not require preheating.
Recommended for:
Food which has to be well-cooked outside and soft or rosy inside, for example lasagne, lamb, roast beef,
whole fish etc.
14
Ventilated Grill Cooking
The infrared grill element and the fan come on. The heat is dispersed mainly by radiation and the fan then
distributes it all over the oven.
Use with the door closed. The temperature can be regulated via the thermostat knob to between 50°
and 175° max.
The oven must be preheated for approximately 5 minutes. For cooking hints, see the chapter “GRILLING
AND AU GRATIN.
Recommended for:
Grilling where quick browning on the outside is required to keep the juices in.
For example: veal steaks, chops, hamburgers etc.
It is recommended that you do not grill for longer than 30 minutes at any one time.
Caution: the oven door becomes very hot during operation. Keep children well out of reach.
Maintaining Temperature After Cooking or Slowly Heating Foods
The upper heating element, the circular element and the fan come on.
The heat is dispersed by forced convection with greater intensity in the upper part.
The temperature can be set to between 50° and 150°C via the thermostat knob.
Recommended for:
Keeping food warm after any type of cooking. Slow heating of cooked food.
Convection Cooking with Ventilation
The upper and lower heating elements come on and the fan.
The heat coming from above and below is dispersed by convection with ventilation.
The temperature can be set to between 50° and 250°C via the thermostat knob.
Recommended for:
Voluminous dishes and large quantities which require the same degree of cooking both inside and out, for
example rolled roasts, turkey, roast legs, cakes etc.
15
Cooking Advice
Sterilization
Sterilization of foods to be conserved, in full and hermetically sealed jars, is done in the following way:
a. Set the switch to position
.
b. Set the thermostat knob to position 185 °C and preheat the oven.
c. Fill the dripping pan with hot water.
d. Set the jars onto the dripping pan making sure they do not touch each other and the door and set the
thermostat knob to position 135 °C.
When sterilization has begun, that is, when the contents of the jars start to bubble, turn off the oven
and let cool.
Regeneration
Set the switch to position
and the thermostat knob to position 150° C.
Bread becomes fragrant again if wet with a few drops of water and put into the oven for about 10 minutes
at the highest temperature.
Simultaneous Cooking of Different Foods
The MULTI-FUNCTION oven set on position
and
gives a simultaneous heterogeneous cooking
of different foods. Different foods such as fish, cake and meat can be cooked together without mixing the
smells and flavors together. This is possible since the fats and vapors are oxidized while passing through
the electrical element and therefore are not deposited onto the foods.
The only precaution to follow are:
– The cooking temperatures of the different foods must be as close to as possible, with a maximum
difference of 20° - 25 °C.
– The introduction of the different dishes in the oven must be done at different times in relation to the
cooking times of each one.
The time and energy saved with this type of cooking is obvious.
Grilling and “Au Gratin”
Grilling may be done without the roasting jack on position
completely envelops the food that is to be cooked.
of the switch, because the hot air
Set the thermostat to position 175 °C and after having preheated the oven, simply place the food on
the rack.
Close the door and let the oven operate with the thermostat on position 175 °C, until grilling is done.
Adding a few dabs of butter before the end of the cooking time gives the golden “au gratin” effect.
Grilling with the oven door closed.
It is recommended that you do not grill for longer than 30 minutes at any one time.
Caution: the oven door becomes very hot during operation. Keep children well out of reach.
16
Roasting
To obtain classical roasting, it is necessary to remember:
– that it is advisable to maintain a temperature between 180° and 200 °C.
– that the cooking time depends on the quantity and the type of foods.
Use of the Grill
– Preheat the oven for about 5 minutes.
– Introduce the food to be cooked, positioning the rack as close to the grill as possible.
– The dripping pan should be placed under the rack to catch the cooking juices and fats.
Grilling with the oven door closed.
Do not grill for longer than 30 minutes at any one time.
Caution: the oven door becomes very hot during operation. Keep children well out of reach.
17
How to Use the Conventional Oven
General Features
Attention:
The oven door
becomes very hot
during operation.
As its name indicates, this is an oven that presents particular features from
an operational point of view. The conventional oven is provided with 3
heating elements which are:
– Bottom element
– Top element
800 W
700 W
– Grill element
1450 W
Note:
Upon first use, it is advisable to operate the oven at the maximum temperature (thermostat knob on
position 250) for 60 minutes in the position and for another 15 minutes in the position to eliminate
possible traces of grease on the heating elements. liquid.
WARNING:
The door is hot, use the handle.
ATTENTION - MOST IMPORTANT
Pay special attention not to touch the hot heating element
inside the oven cavity.
Thermostat Knob (fig. 18)
This only sets the cooking temperature and does not switch the oven on.
Rotate clockwise until the required temperature is reached (from 50 to 250°C).
The light between the thermostat and the function selector will illuminate when the oven is switched on
and turns off when the oven reaches the correct temperature.
The light will cycle on and off during cooking in line with the oven temperature.
Fig. 17
Fig. 18
18
Function Selector Knob (fig. 17)
Rotate the knob clockwise to set the oven for one of the following functions.
Oven Light
By setting the knob to this position, only the oven light comes on.
It remains on in all the cooking modes.
Traditional Convection Cooking
The upper and lower heating elements come on.
The heat is dispersed by natural convection and the temperature must be set to between 50° and 250°C
via the thermostat knob. The oven must be preheated before cooking.
In the
position the rotisserie motor come on for cooking with the rotisserie.
Recommended for:
Food that requires the same degree of cooking both inside and out, for example roasts, spare pork ribs,
meringues etc.
Traditional Grilling
The infrared grill element comes on. The heat is dispersed by radiation.
Use with the oven door closed and the thermostat knob to position 225°C for max 15 minutes, then
to position 175°C.
In the
position the rotisserie motor come on for cooking with the rotisserie.
For cooking hints, see the chapter “USE OF THE GRILL”.
Recommended for:
Intense grilling, browning, cooking au gratin and toasting etc.
It is recommended that you do not grill for longer than 30 minutes at any one time.
Caution: the oven door becomes very hot during operation.
Keep children well out of reach.
19
Use of the Grill
Switch the grill on, setting the two knobs:
– Function selector to
or
position.
– Thermostat selector to position 225°C for 15 minutes then to 175°C.
Leave to warm up for approximately 5 minutes with the door closed.
Place the food inside positioning the rack as near as possible to the grill.
Insert the drip pan under the rack to collect the cooking juices.
Grilling with the oven door closed and do not for longer than 30 minutes at any one time.
Attention: the oven door becomes very hot during operation.
Keep children away.
Rotisserie
The oven is equipped with a rotisserie.
This device is made up of:
– an electrical motor mounted on the rear part of the oven
– a stainless steel rod, equipped with a detachable athermic handle and 2 recordable forks
– a rod support to be inserted into the central rack holders of the oven.
Use of the Rotisserie
– Insert the dripping pan into the lowest rack holders of the oven and insert the rod support into the
intermediate rack holders.
– Put the meat to be cooked onto the rod, being careful to secure it in the center with the special forks.
– Insert the rod into the motor opening and rest it onto the support of the spit collar; then remove the
grip by turning it to the left.
The rotation direction of the rotisserie can be either clockwise or counter-clockwise.
Fig. 19
20
Do’s and do not’s
– Do always grill with the oven door closed.
– Do read the user instructions carefully before using the cooker for first time.
– Do allow the oven to heat for one and a half hours, before using for the first time, in order to expel any
smell from the new oven insulation, without the introduction of food.
– Do clean your oven regularly.
– Do remove spills as soon as they occur.
– Do always use oven gloves when removing food shelves and trays from the oven.
– Do not allow children near the cooker when in use.
– Do not allow fat or oils to build up in the oven trays, or oven base.
– Do not place cooking utensils or plates directly onto the oven base.
– Do not grill food containing fat without using the grid.
– Do not cover the grilling grid with aluminium-foil.
– Do not use the oven tray for roasting.
– Do not place hot enamel parts in water. Leave them to cool first.
– Do not allow vinegar, coffee, milk, saltwater, lemon or tomato juice to remain in contact with enamel
parts (inside the oven and on the oven tray).
– Do not use abrasive cleaners or powders that will scratch the surface of the stainless steel and the
enamel.
– Do not attempt to repair the internal workings of your cooker.
– Do remove the protective film before the first use.
– Fire risk! Do not store flammable material in the oven or in the storage compartment.
21
For Your Safety
– The product should only be used for its intended purpose which is for the cooking of domestic
foodstuffs.
– Under no circumstances should any external covers be removed for servicing or maintenance except by
suitably qualified personnel.
– Attention: The appliance gets very hot, mainly around the cooking areas. It is very important
that children are not left alone in the kitchen when you are cooking.
– Household appliances are not intended to be played with by children.
– Keep children away from the appliance during use.
– Children, or persons with a disability which limits their ability to use the appliance, should have a
responsible person to instruct them in its use. The instructor should be satisfied that they can use the
appliance without danger to themselves or their surroundings.
– Do not operate your appliance by means of an external timer or separate remote-control system.
Important Notes
Installation, and any demonstration, information or adjustments are not included in the warranty.
The cooker must be installed by a suitably qualified and registered person in accordance with the relevant
Standards.
22
Care and Maintenance
Important:
As a safety measure, before you start cleaning the cooker be sure to disconnect it from the mains supply.
Do not use cleaning products with a chlorine or acidic base.
Do not use a steam cleaner because the moisture can get into the appliance thus make it
unsafe.
The use of suitable protective clothing/gloves is recommended when handling or cleaning of
this appliance.
Warning
When correctly installed, your product meets all safety requirements laid down for this type of product
category.
However special care should be taken around the rear or the underneath of the appliance as these areas are
not designed or intended to be touched and may contain sharp or rough edges, that may cause injury.
Flexible Tube
From time to time, check the flexible tube connecting the gas supply to the cooker.
It must be always in perfect condition; in case of damage arrange for it to be replaced by a suitably qualified
and registered installer.
Gas Taps
If a tap becomes stiff, do not force; contact your Local Service Centre.
Cleaning the Hob
Spillage on the hob can usually be removed by a damp soapy cloth. More obstinate stains can be removed
by rubbing gently with a soapy nylon (non metal) scouring pad or mild household cleaner.
Enamelled Parts
All the enamelled parts must be cleaned with a sponge and soapy water only or other non-abrasive
products.
Dry preferably with a micro fibre or soft cloth.
23
Stainless Steel, Aluminium, Painted Parts and Silk-Screen Printed Surfaces
Clean using an appropriate product. Always dry thoroughly.
Stainless steel surfaces: can be cleaned with an appropriate stainless steel cleaner.
IMPORTANT: these parts must be cleaned very carefully to avoid scratching and abrasion. You are advised
to use a soft cloth and neutral soap.
CAUTION: Do not use abrasive substances or non-neutral detergents as these will irreparably
damage the surface.
Changing the Oven Light
1. Disconnect the electrical power supply (for example, by switching off the main power switch).
2. Unscrew the light cover
3. Fit a new bulb.
4. Refit the cover.
Note:
Use only bulbs designed to resist up to 300°C with the following characteristics: 230 V, type E14 and same
power (check watt power as stamped in the bulb itself) of the replaced bulb.
24
Burners and Grids
– These parts can be removed and cleaned with appropriate products.
– After cleaning, the burners and their flame spreaders must be well dried and correctly replaced.
– It is very important to check that the burner flame spreader and the cap have been correctly positioned.
Failure to do so can cause serious problems.
– Check that the electrode “S” (figs. 20-22) is always clean to ensure trouble-free sparking.
– Check that the sensor “T” (figs. 20-22) next to each burner is always clean to ensure correct operation
of the safety valves.
– Both the sensor and ignition plug must be very carefully cleaned.
– Note: To avoid damage to the electric ignition do not use it when the burners are not in
place.
Correct Positioning of the Burners (Auxiliary, Semi-Rapid and Rapid Burners)
– It is very important to check that the burner flame spreader “F” and the cap “C” have been correctly
positioned (see figs. 20 and 21). Failure to do so can cause serious problems.
C
F
Ignitor “S”
Sensor “T”
Fig. 20
Fig. 21
25
Correct Position of Triple Ring Burner
The triple ring burner must be correctly positioned (see fig. 22); the burner ribs must be fitted in their
housing as shown by the arrow.
The burner correctly positioned must not rotate (fig. 23).
Then position the cap “A“ and the ring “B“ (figs. 23 - 24)
Sensor “T”
Ignitor “S”
Fig. 22
A
B
Fig. 23
Fig. 24
26
Removal of the Inner Glass Door Panel
– The inner glass door panel can easily be removed for cleaning by unscrewing the four screws (fig. 25).
– When re-assembly ensure that the inner glass is correctly positioned and do not over tighten the
screws.
Do not use harsh abrasive cleaners or sharp metal scrapers to clean the oven door glass since
they can scratch the surface, which may result in shattering of the glass.
Fig. 25
Storage Compartment
– The storage compartment is accessible through the pivoting panel.
Attention: Do not store flammable material in the oven, or the storage compartment.
Fig. 26
27
Inside of Oven
The oven should always be cleaned after use when it has cooled down.
The cavity should be cleaned using a mild detergent solution and warm water. Suitable proprietary
chemical cleaners may be used after first consulting with the manufacturers recommendations and testing
a small sample of the oven cavity. Abrasive cleaning agents or scouring pads/cloths should not be used
on the cavity surface.
NOTE: The manufacturers of this appliance will accept no responsibility for damage caused by chemical
or abrasive cleaning.
Let the oven cool down and pay special attention no to touch the hot heating elements inside
the oven cavity.
Assembling and Dismantling of the Side Runner Frames
– Fit the side runner frames into the holes on the side walls inside the oven (Fig. 27).
– Slide the tray and rack into the runners (Fig. 28).
The rack must be fitted so that the safety catch, which stops it sliding out, faces the inside of the oven.
– To dismantle, operate in reverse order.
Fig. 28
Fig. 27
28
Removing the Oven Door
Fig. 29a
Please operate as follows:
– Open the door completely.
– The swivel retainers of the rh and lh hinges (fig. 29a) are
hooked onto the metal bar above them (fig. 29b).
– Lift the oven door slightly. The noch on the bottom of the
hinge will disengage (fig. 29c).
– Now pull the oven door forwards off the appliance. Release
both hinge sections from the slots (fig. 29d).
Fig. 29b
Door Assembly
– Grip the door (as indicated in figure 29) and refit it in reverse
order of removing procedure.
Fig. 29c
Fig. 29d
Fig. 29
29
FOR THE INSTALLER
Location
The appliance may be installed in a kitchen, Kitchen/diner or a bed sitting room, but not in a room or
space containing a bath or a shower.
The appliance must not be installed in a bed-sitting room of less than 20m3.
The appliance is designed and approved for domestic use only and should not be installed in a commercial,
semi commercial or communal environment.
Your product will not be guaranteed if installed in any of the above environments and could affect any
third party or public liability insurances you may have.
This cooker has class “2/1” overheating protection so that it can be installed next to
cabinet.
a
– If the cooker is installed adjacent to furniture which is higher than the gas hob cooktop, a gap of at least
200mm must be left between the side of the cooker and the furniture.
– The furniture walls adjacent to the cooker must be made of material resistant to heat.
– The veneered synthetic material and the glue used must be resistant to a temperature of 90°C in order
to avoid ungluing or deformations.
– Curtains must not be fitted immediately behind appliance or within 500mm of the sides.
– It is essential that the cooker is positioned as stated below.
– If the cooker is located on a pedestal it is necessary to provide safety measures to prevent falling out.
– The cooker must be installed by a qualified technician and in compliance with local safety
standards.
200 mm
500 mm
Fig. 30
30
Assembling the Backguard
– Remove the two spacers “A” and the
screw “B” from the rear of the cooktop.
– Assemble the backguard as shown in
figure 31 and fix it by screwing the central
screw “B” and the spacers “A”.
B
A
Fig. 31
Fitting the Adjustable Feet
– The adjustable feet must be fitted to the base of the cooker before use.
– Rest the rear of the cooker an a piece of the polystyrene packaging exposing the base for the fitting of
the feet.
– Fit the 4 legs by screwing them tight into the support base as shown in picture 32.
WARNING
When raising cooker to upright position always ensure two people carry out this manoeuvre
to prevent damage to the adjustable feet (fig. 34).
Fig. 32
Fig. 33
31
Warning
To move the cooker always ensure two people carry out this
manoeuvre to prevent damage to the appliance (fig. 34).
Warning
Be carefull: do not lift the cooker by the door handle
(fig. 35).
Warning
When moving cooker to its final position DO NOT DRAG
(fig. 36).
Lift feet clear of floor (fig. 34).
Fig. 34
Levelling the Cooker
The cooker may be levelled by screwing the lower ends of
the feet IN or OUT (fig. 37).
Fig. 35
Fig. 37
Fig. 36
32
Stability Bracket
We recommend a stability bracket is fitted to the cooker.
The type shown in fig. 39 can be purchased from most plumbers merchants and do it yourself (D.I.Y.)
shops.
Existing slot in
rear of cooker
Brackets
Dotted line showing the
position of cooker when fixed
Fig. 38
Fig. 39
Outline of cooker backplate
at the engagement slot
Wall fixing
Floor fixing
33
Provision for Ventilation
– The appliance should be installed into a room or space with an air supply in accordance with BS 5440-2:
2000.
– For rooms with a volume of less than 5m3 - permanent ventilation of 100cm2 free area will be required.
– For rooms with a volume of between 5m3 and 10m3 a permanent ventilation of 50 cm2 free area will be
required unless the room has a door which opens directly to the outside air in which case no permanent
ventilation is required.
– For rooms with a volume greater than 10m3 - no permanent ventilation is required.
Note: Regardless of room size, all rooms containing the appliance must have direct access to
the outside air via an openable window or equivalent.
– Where there are other fuel burning appliances in the same room, BS 5440-2: 2000 should be consulted
to determine the correct amount of free area ventilation requirements.
– The above requirements allow also for use of a gas oven and grill but if there are other gas burning
appliances in the same room, consult a qualified engineer.
34
Gas Installation
Important Note
This appliance is supplied for use on NATURAL GAS or LPG (check the gas regulation label attached on
the appliance).
– Appliances supplied for use on NATURAL GAS: they are adjusted for this gas only and cannot be used on
any other gas (LPG) without modification. The appliances are manufactured for conversion to LPG.
– Appliances supplied for use on LPG: they are adjusted for this gas only and cannot be used on any
other gas (NATURAL GAS) without modification. The appliances are manufactured for conversion to
NATURAL GAS.
If the NATURAL GAS/LPG conversion kit is not supplied with the appliance this kit can be purchased by
contacting the After-Sales Service.
Installation and Service Regulations (United Kingdom)
It is a legal requirement that all gas appliances are Installed and Serviced by a competent person in
accordance with the current editions of the following Standards and Regulations or those regulations
appropriate to the geographical region in which they are to be installed:
– Gas Safety (Installation and Use) Regulations
– Building Regulations
– British Standards
– Regulations for Electrical Installation
Installation and service of any gas product must be made by a suitably qualified and registered person
competent on the type of product being installed or serviced and holding a valid certificate of competence
for the work being carried out. Currently the proof of competence is the Accredited Certification Scheme
(ACS) or S/NVQ that has been aligned to the ACS.
It is also a requirement that all businesses or self employed installers are members of a class of person
approved by the Health and Safety Executive.
Failure to install the appliance correctly could invalidate any manufacturers warranty and lead to
prosecution under the above quoted regulation.
35
Gas Connection
The installation of the gas appliance to Natural Gas or LP Gas must be carried out by a suitably qualified
and registered installer. Installers shall take due account of the provisions of the relevant British Standards
Code of Practice, the Gas Safety Regulations and the Building Standards (Scotland) (Consolidation)
Regulations issued by the Scottish Development Department.
Installation to Natural Gas
Installation to Natural Gas must conform to the Code of Practice, etc.
The supply pressure for Natural Gas is 20 mbar.
The installation must conform to the relevant British Standards.
Installation to LP Gas
When operating on Butane gas a supply pressure of 28-30 mbar is required. When using Propane gas a
supply pressure of 37 mbar is required.
The installation must conform to the relevant British Standards.
Warning: Only a suitably qualified and registered installer, also with technical knowledge of electricity
should install the appliance. He should observe the Regulations and Codes of Practice governing such
installation of gas appliances.
Note: It is recommended that the gas connection to the appliance is installed with a flexible connecting
tube made to BS5386.
Notes:
– Flexible hoses can be used where the sited ambient temperature of the hose does not exceed
70°C. These hoses must be manufactured in accordance with BS669 part 1 and be of the
correct construction for the type of gas being used.
– Gas hoses designed for natural gas MUST NOT be used for supplying LPG gas (LPG gas hoses
can be identified by a either a red band or stripe on the rubber outer coating of the hose).
The hose should not be crushed or trapped or be in contact with sharp or abrasive edges.
Using a suitable leak detection fluid solution (e.g. Rocol) check each gas connection one at a time by
brushing the solution over the connection.
The presence of bubbles will indicate a leak.
If there is a leak, tighten the fitting and then recheck for leaks.
IMPORTANT!
Do not use a naked flame to test for leaks.
36
Gas Connection
Cat: II 2H3+
The gas supply must use the nearest gas inlet pipe which is located at the left or the right hand side at the
rear of the appliance (fig. 40).
The hose should also be connected in such away that it does not touch the floor.
To screw the connecting tube operate with two spanners (fig. 41).
The unused end inlet pipe must be closed with the plug interposing the gasket.
After connecting to the mains, check that the coupling are correctly sealed, using soapy
solution, but never a flame.
Fig. 41
Left gas
inlet pipe
Right gas
inlet pipe
Plug
1/2” BSP (male)
Fig. 40
37
Important Prescriptions for Gas Connection
Rear wall
Suggested area for
gas mains connection
Fig. 42
38
Conversion to Natural Gas or to LPG
Injectors Replacement of Top Burners
Every cooker is provided with a set of injectors for the various types of gas.
Injectors not supplied can be obtained from the After-Sales Service.
Select the injectors to be replaced according to the table at page 39.
The nozzle diameters, expressed in hundredths of a millimetre, are marked on the body of each injector.
To replace the injectors proceed as follows:
– Remove the pan supports, the burner caps and flame speaders.
– Using a wrench, substitute the nozzle injectors “J” (figs. 43 - 44) with those most suitable for the kind of
gas for which it is to be used (see “Table for the choice of the injectors”).
The burners are constructed in such a way so as not to require the regulation of the primary air.
Auxiliary,
Semi-Rapid
and Rapid
burners
Triple Ring
burner
J
J
Fig. 43
Fig. 44
Adjusting of the Minimum of the Top Burners
Considering that in the minimum position the flame must have a length of about 4 mm and must remain lit
even with a quick turn from the maximum position to that of minimum.
The flame adjustment is done in the following way:
– Turn on the burner
– Turn the tap to the MINIMUM position
– Take off the knob
– With a thin screwdriver turn the screw “F“ until adjustment is
correct (fig. 45).
Normally for LPG, tighten up the regulation screw.
F
Fig. 45
39
Table for the Choice of the Injectors
Cat: II 2H3+
G20 - 20 mbar
Burners
Nominal
Power
kW
Reduced
Power
kW
G30 - 28-30 mbar
G31 - 37 mbar
Ø Injector
Ø Injector
1/100 mm
1/100 mm
Auxiliary (A)
Semi-Rapid (SR)
Rapid (R)
1,00
1,75
3,00
3,50
0,30
0,45
0,75
1,50
50
65
85
95
72 (X)
97 (Z)
115 (Y)
135 (T)
Triple Ring (TR)
Increase of Air Necessary for Gas Combustion (2 m3/h x kW)
Burners
Air necessary for combustion (m3/h)
Auxiliary (A)
Semi-Rapid (SR)
Rapid (R)
2,00
3,50
6,00
7,00
Triple Ring (TR)
Lubrication of the Gas Taps
The operations must be executed by a qualified technician.
IMPORTANT: All intervention regarding installation maintenance and conversion of the
appliance must be fulfilled with original factory parts.
The manufacturer declines any liability resulting from the non-compliance of this obligation.
40
Electrical Installation
WARNING! Electricity can be extremely dangerous.
This appliance must be earthed.
The appliance must be connected to the electrical network verifying above all that the voltage corresponds
to the value indicated on the specifications plate and that the cables section of the electrical plant can bear
the load which is also indicated on the plate.
It is recommended that the appliance is connected directly to the mains by fixed wiring, placing a double
pole switch with minimum opening between the contacts of 3 mm.
The power supply cable must not touch the hot parts and must be positioned so that it does not exceed
75°C at any point.
Once the cooker has been installed, the switch must always be accessible.
Before effecting any intervention on the electrical parts the appliance must be disconnected
from the network.
Electrical Feeder Cable Connection
230 V
To connect the feeder cable to the cooker it is necessary to:
– Remove the screw that hold shield “A” behind the cooker
(fig. 47).
– Insert the feeder cable of the suitable section (as described in
L1
N
(L2
PE
the next chapter) into the cable clamp “D”.
– Connect the phase and earth cables to the terminal block “B”
according to the diagram in figure 46.
)
Fig. 46
– Pull the feeder cable and block it with cable clamp “D”.
– Re-mount shield “A”.
Feeder Cable Section
Type H05RRF
230 V~
3 x 2.5 mm2 (**)
PE
D
(**) - Connection with wall box connection.
Earth cable must be 2 cm longer than neutral and live
cables.
B
A
Fig. 47
41
Connection to Fixed Wiring
A double pole switch must be provided no further than 2 metres from the appliance to the electrical
supply.
The appliance should be connected to a DOUBLE POLE SWITCHED FUSED SPUR OUTLET, similar to
that shown in Fig. 48.
DOUBLE POLE SWITCHED
FUSED SPUR OUTLET
ON
FUSE
Use a suitable FUSE in accordance
with the appliance power rating.
Fig. 48
We recommend that the appliance is connected by a suitably qualified person who will comply with the
IEE and local regulation.
42
Appliance Servicing
CDA provide a quality and effective after-sales service to cover all your servicing needs.
Please attach your receipt to this page for safekeeping.
Please help us to help you by having the following information available when booking a service-call:
1. Model type, make and model – see the product data plate.
2. Evidence of installation / purchase date.
3. Retailer where appliance was purchased.
4. Clear and concise details of the fault.
5. Full address including postcode and any contact phone numbers.
Contact telephone numbers
CDA Customer Care Department
– Telephone: 01949 862012
– Fax: 01949 862003
– Email: [email protected]
43
Guarantee
CDA appliances carry a five-year parts and a one-year labour guarantee.
CDA will repair or replace any defect or part attributable to faulty material or workmanship. Within the
first year this will be free of both labour and parts charges. After the first year and within five years, the
parts will be supplied free of charge provided that the repair is carried out by an agent authorised by CDA
and the labour will be charged at the commercial rate applicable at the time of repair.
The appliance must have been installed by a suitably qualified person and in accordance with the
manufacturer’s instructions and current legislation. The guarantee does not cover faults caused by the
incorrect fitting of appliances.
Limit of Cover
– The guarantee does not cover cosmetic damage e.g. discolouration or oxidisation.
– Proof of purchase or installation date must be produced before a service-call will be booked.
– The appliance must be used for domestic purposes only. Appliances used for commercial or professional
purposes are not covered by the guarantee. Commercial warranty is available at extra cost.
– The appliance must not be modified or tampered with or repair attempted by any unauthorised
person.
– The guarantee does not cover damage caused in transit or by misuse, accident, abuse or neglect.
– The guarantee does not cover routine maintenance.
– Use of parts not supplied or recommended by |C|D|A| will invalidate the warranty.
– Rubber seals, filters, removable glass parts, control knobs and buttons, fuses and light bulbs will need
replacing periodically and are not covered by the guarantee.
– Second-hand or reconditioned appliances are not covered by the guarantee.
The conditions under which this guarantee is offered are in addition to the statutory rights of the domestic
purchaser and these statutory rights are not affected by this guarantee.
CDA reserve the right to change specification without prior notice.
Cod. 1103541- ß2
To contact our Customer Care Department, or for Service,
please contact us on the details below.
Customer Care Department • The
Group Ltd. • Harby Road • Langar • Nottinghamshire • NG13 9HY
|