USE, INSTALLATION AND MAINTENANCE
INSTRUCTIONS FOR BUILT-IN HOT PLATES
Dear Customer
Thank you for purchasing a Blanco Cooktop.
Before we continue telling you about this cooktop, we cordially invite you to become part of the Blanco family by
subscribing to ongoing information and invitations. Please visit our website where you can subscribe and request
fill in the subscription details.
You will find that the clean lines and modern look of your Blanco Cooktop blends perfectly with your kitchen décor.
It is easy to use and performs to a high standard.
Blanco also makes a range of products that will enhance your kitchen such as ovens, rangehoods, dishwashers,
microwaves, sinks and taps.
There are models to complement your new Blanco Cooktop.
Of course we make every effort to ensure that our products meet all your requirements, and our Customer
Relations department is at your disposal, to answer your questions and to listen to all your suggestions (see back
cover of manual).
Please complete the warranty section of this manual and keep your receipt as proof of purchase. Retain all
documents relating to the purchase of this products.
Blanco is committed to providing increasingly efficient products that are easy to use, respect the environment and
are attractive and reliable.
BLANCO
MODELS: BCGC74 - BCGC52
CRYSTAL GLASS COOKTOP
MOD.: .......................
We ask that you carefully read the instructions within this booklet to enable you to abtain quality results from the outset.
The appliance must be installed only by an authorised person in compliance with the instructions provided. The manufacturer
declines all responsability for improper installation which may harm persons and animals and damage property.
The appliance must be used for the purpose for which it was expressly designed. Any other use (eg heating rooms) is considered to
be improper and consequently dangerous. The manufacturer declines all responsability for damage resulting from improper and
irresponsible use.
The manufacturer shall not be held responsible for any inaccuracies in this handbook due to printing or transcription errors. The
designs in the figures are purely indicative.
The manufacturer also reserves the right to make any modifications to the products as may be considered necessary, useful or in
the interests of the user, without jeopardizing the main functional and safety features on the products themselves.
If your cooktop requires service, please contact your local customer service centre or your nearest Blanco agent listed at the back of
this booklet.
COD. 01019GG - 18.07.2006
USE
HOW TO USE THE BURNERS
In order to achieve maximum efficiency with the least
possible gas consumption:
- Use adequate pans for each burner (consult the
following table and fig. 2).
- When the pan comes to the boil, set the knob to the
reduced rate position (small flame fig. 1).
- Always place a lid on the pans.
1) BURNERS
A diagram is screen-printed above each knob on the
front panel. This diagram indicates to which burner
the knob in question corresponds. After having
opened the gas mains or gas bottle tap, light the
burners as described below:
- Manual ignition
Push and turn the knob corresponding to the
required burner in an anticlockwise direction until it
reaches the full on position (large flame fig. 1), then
place a lighted match near the burner.
Burners
Power ratings
Pan Ø in cm
Natural
U-LPG
Ultra rapid
Semirapid
Auxiliary
11.9 MJ 11.9 MJ
22 ÷ 28
16 ÷ 18
10 ÷ 14
- Electrical ignition
6.3 MJ
3.6 MJ
6.3 MJ
3.6 MJ
Push and turn the knob corresponding to the
required burner in an anticlockwise direction until it
reaches the full on position (large flame fig. 1), then
depress and release the ignition button.
WARNINGS:
- Burners with flame failure device may only be
ignited when the relative knob has been set to
the Full on position (large flame fig. 1).
- Matches can be used to ignite the burners in a
blackout.
- Never leave the appliance unattended when the
burners are being used. Make sure there are no
children in the near vicinity. Particularly make
sure that the pan handles are correctly
positioned and keep a check on foods requiring
oil and grease to cook since these products can
easily catch fire.
- Automatic electrical ignition
Push and turn the knob corresponding to the
required burner in an anticlockwise direction until it
reaches the full on position (large flame fig. 1), then
depress the knob.
- Lighting burners equipped with flame failure
device
The knobs of burners equipped with flame failure
device must be turned in an anticlockwise direction
until they reach the full on position (large flame
fig. 1) and come to a stop. Now depress the knob in
question and repeat the previously indicated
operations.
- Do not spray aerosols in the vicinity of this
appliance while it is in operation.
Keep the knob depressed for about 10 seconds
once the burner has ignited.
- This appliance is not to be installed in marine
craft. Where this appliance is installed in a
caravan, it shall not be used as a space heater.
- Do not store or use flammable liquids or items in
the vicinity of the hotplate.
Note: you are advised not to try and light a burner if
the flame divider (Burner Cap) is not correctly placed.
In the event of burner flames being accidentally
extinguished, turn off the burner control and do not
attempt to re-ignite the burner for at least 1 minute.
FIG. 1
FIG. 2
3
USE
Notes:
Use of a gas cooking appliance produces heat and moisture in the room in which it is installed. The
room must therefore be well ventilated by keeping the natural air vents clear (fig. 3) and by activating
the mechanical aeration device (rangehood or electric fan fig. 4 and fig. 5).
Intensive and lengthy use of the appliance may require additional ventilation. This can be achieved by
opening a window or by increasing the power of the mechanical exhausting system if installed.
Star Trivet: use star trivet whenever using a small pot.
Abnormal Operation:
Any of the following are considered to be abnormal operation and may require servicing:
- Yellow tipping of the hob burner flame.
- Sooting up of cooking utensils.
- Burners not igniting properly.
- Burners failing to remain alight.
- Burners extinguished by cupboard doors.
- Gas valves which are difficult to turn.
In case the appliance fails to operate correctly, contact the authorised service provider in your area.
Do not place anything, eg. flame tamer, asbestos
Symbol 1
Symbol 2
Symbol 3
mat, between pan and pan support as serious
damage to the appliance my result.
Do not remove the pan support and enclose the
burner with a wok stand as this will concentrate and
deflect heat onto the hotplate.
Do not use large pots or heavy weights which can
bend the pan support or deflect flame onto the
hotplate.
(*) Air inlet - minimum section 100 cm2
FIG. 3
FIG. 4
FIG. 5
4
CLEANING
IMPORTANT:
established by the rounded corners, which
should be set towards the side edge of the hot
plate.
- Do not force the taps if they are difficult to open
or close. Contact the technical assistance
service for repairs.
Always disconnect the appliance from the gas
and electricity mains before carrying out any
cleaning operation.
2) HOT PLATE
Periodically wash the hot plate, the cast iron pan
support, the enamelled burner caps “C” and the
burner heads “M” (see fig. 6) with lukewarm soapy
water. Following this, all parts should be thoroughly
rinsed and dried. Never wash them while they are
still warm and never use abrasive powders. Do not
allow vinegar, coffee, milk, salted water, lemon or
tomato juice from remaining in contact with the
enamelled surfaces for long periods of time.
- Do not use steam jets for cleaning the cooktop.
PREVENTATIVE MAINTENANCE
This cooktop should not require ongoing
maintenance provided you ensure:
- All spillages are cleaned up as soon as they occur.
- Burners are kept clean.
- Burner ports are free of debris, food any anything
else that may cause an obstruction.
- Electrode and thermocouples are kept clean.
- Burners are re-assembled correctly.
- Do not get water in the area where the injectors are
located.
WARNINGS:
Comply with the following instructions, before
remounting the parts:
- Check that burner head slots “M” (fig. 6) have
not become clogged by foreign bodies.
- Check that enamelled burner cap “C” (fig. 6)
have correctly positioned on the burner head. It
must be steady.
- The exact position of the pan support is
FIG. 6
5
INSTALLATION
mm above the construction above the top of the
TECHNICAL INFORMATION FOR THE
INSTALLER
burner and no construction shall be within 450 mm
above the top of the burner. A minimum depth of 60
mm from the top of the work surface must be
provided for this appliance.
This appliance shall be installed only by authorised
personnel and in accordance with the manufacturer’s
installation instructions, local gas fitting regulations,
municipal building codes, water supply regulations,
electrical wiring regulations, AS 5601/AG 601 – Gas
Installations and any other statutory regulations.
4) FIXING THE HOT PLATE
The hot plate has a special seal which prevents
liquid from infiltrating into the cabinet. Strictly comply
with the following instructions in order to correctly
apply this seal:
3) INSTALLING THE HOT PLATE
Check that the appliance is in a good condition after
having removed the outer packaging and internal
wrappings from around the various loose parts. In
case of doubt, do not use the appliance and contact
qualified personnel.
Never leave the packaging materials (cardboard,
bags, polystyrene foam, nails, etc.) within
children’s reach since they could become
potential sources of danger.
The measurements of the opening made in the top
of the modular cabinet and into which the hot plate
will be installed are indicated in fig. 7.
Always comply with the measurements given for
the hole into wich the appliance will be recessed
(see fig. 7).
- Take off all the movable parts of the hob.
- Cut the seal in 4 parts of the necessary length to
positioning it on the 4 edges of the crystal.
- Overturn the hot plate and correctly position seal
“E” (fig. 8) under the edge of the hob itself, so that
the outer side of the seal perfectly matches the
outer perimetral edge of the hob. The ends of the
strips must fit together without overlapping.
- Evenly and securely fix the seal to the hob,
pressing it in place with the fingers.
- Remove the strip of protective paper from the seal.
Fit the hot plate into the hole in the cabinet and lock
it in place with the relative fixing screws “F” of the
fixing hooks “G” (see fig. 9).
Any adjoining wall surface situated within 200 mm
from the edge of any hob burner must be a suitable
non-combustible material for a height of 150 mm for
the entire length of the hob. Any combustible
construction above the hotplate must be at least 600
COMPLY WITH THE DIMENSIONS
Overall Dimensions: 680 x 500 mm
A
B
2B
4B
480
328
645
470
FIG. 7
FIG. 8
FIG. 9
6
INSTALLATION
Natural Gas
5) LOCATION AND VENTILATION
Natural Gas installations require the connection of a gas
regulator at the appliance. This regulator is supplied with
the appliance on purchase.
Assemble the regulator (noting the gas flow direction) and
transition pieces (supplied with the appliance), in
accordance with figure 10.
The transition piece on the supply side of the regulator
must be provided by the installer.
The appliance is factory set for Natural Gas. The test point
pressure should be adjusted to 1.00 kPa with the wok
burner operating at maximum.
Ventilation must be in accordance with
AS5601/AG 601 – Gas Installations.
In general, the appliance should have adequate ventilation for
complete combustion of gas, proper flueing and to maintain
temperature of immediate surroundings within safe limits.
The wall and bench surfaces must be capable of sustaining
temperatures of 75°C.
All laminates, fixing adhesive and surfacing materials should
be certified suitable for this temperature.
6) GAS CONNECTION
This gas connection is male 1/2” BSP and is situated at the
rear of the appliance, 415 mm from the right hand side and
55 mm from the rear of the cooktop.
Liquified Petroleum Gas
In a Universal LPG installation the gas regulation is made
at the gas cylinder and regulation at the appliance is not
required. The supply pressure should be 2.75 kPa. To
connect supply to the appliance use transition pieces as
shown in figure 11. These pieces are supplied with the
appliance on purchase.
A. The hotplate can be connected with rigid pipe as specified
in AS5601 table 3.1.
B. If installing with a hose assembly, install with a hose
assembly that complies with AS/NZS 1869 (AGA
Approved), 10mm ID, class B or D, no more than 1.2m long
and in accordance with AS5601. Ensure that the hose does
not contact the hot surfaces of the hotplate, oven,
dishwasher or any other appliance that may be installed
underneath or next to the hotplate. The hose should not be
subjected to abrasion, kinking or permanent deformation and
should be able to be inspected along its entire length with the
cooktop in the installed position.
WARNING:
THE BURNER FLAME MUST BE ADJUSTED BY THE
INSTALLER.
FAULTY INSTALLATION WILL NOT BE COVERED
UNDER WARRANTY.
Unions compatible with the hose fittings must be used and
all connections tested for gas leaks.
The gas supply connection for the hose assembly must be
accessible.
FIG. 11
FIG. 10
7
INSTALLATION
a) Data Label
7) ELECTRICAL CONNECTION
The Data Label is located on the underside of the
hotplate. A duplicate Data Label is supplied to adhere
in an accessible area next to the hotplate. This
hotplate is suitable for Natural Gas and Universal
LPG; ensure that the available gas supply matches
the Data Label.
The appliance is supplied with a 1800 mm long
flexible supply lead.
The point of attachment for this lead is located at
the rear and on the underside of the appliance
380 mm from the right hand side.
The voltage and power consumption are detailed on
the underside of the appliance. Ensure that the
appliance is correctly rated to the supply.
Connect appliance by way of a switched power
point.
b) Before Leaving
Check that there are no gas leaks, but do not use a
naked flame to detect gas leaks. Ignite all burners to
ensure correct operation of gas valves, burners,
ignition and if fitted, flame failure valves. Turn gas
taps to low flame position and observe stability of the
flame. When satisfied with the hotplate, please
instruct the user on the correct method of operation.
In case the appliance falls to operate correctly after
all checks have been carried out, refer to the
authorised service provider in your area.
THE APPLIANCE MUST BE EARTHED
Ensure that this power point is properly earthed.
Look at the connection wiring diagrams
(fig. 12 or 12/A).
FIG. 12
FIG. 12/A
8
ADJUSTMENTS
Always disconnect the appliance from the
- Insert a small screwdriver “D” into hole “C” (fig. 13)
and turn the throttle screw to the right or left until the
burner flame has been adequately regulated to the
“Reduced rate” position.
Check that the flame does not go out when the knob
is sharply switched from the “Full on” to the “Reduced
rate” position.
electricity main before making any adjustments.
All seals must be replaced by the technician at
the end of any adjustments or regulations.
Our burners do not require primary air
adjustment.
8) TAPS
Our taps are suitable for all gas, they are male conical
type.
It is understood that only burners operating with
Natural gas should be subjected to the above
mentioned adjustments. The screw must be fully
locked when the burners operate with Liquid gas.
“Reduced rate” adjustment
- Switch on the burner and turn the relative knob to
the “Reduced rate” position (small flame fig. 1).
- Remove knob “M” (fig. 13) of the tap, which is simply
pressed on to its rod.
FIG. 13
9
CONVERSIONS
9) U-LPG TO NATURAL GAS
CONVERSION PROCEDURE
10) NATURAL GAS TO UNIVERSAL
LPG CONVERSION PROCEDURE
Appliance models: Gas crystal glass hotplate
models:
Appliance models: Gas crystal glass hotplate
models:
BCGC74 4 Burners
BCGC52 2 Burners
BCGC74 4 Burners
BCGC52 2 Burners
1. Remove each burner cap and burner skirt.
2. Remove the U-LPG main injector with a
7 mm/VF tube spanner and replace with the
appropriate size Natural Gas main injector for each
burner. The following injector sizes are required for
Natural Gas:
1. Remove each burner cap and burner skirt.
2. Remove the Natural Gas main injector with a
7 mm/VF tube spanner and replace with the
appropriate size U-LPG main injector for each
burner. The following injector sizes are required for
U-LPG:
Burner
Main injector
Burner
Main injector
Wok
Semi Rapid
Auxiliary
1.55 mm
1.12 mm
0.85 mm
Wok
Semi Rapid
Auxiliary
0.95 mm
0.70 mm
0.53 mm
3. Shut off gas supply to the appliance.
4. Disconnect gas inlet pipe from the U-LPG Gas
test point inlet fitting.
5. Remove the U-LPG test point inlet fitting from the
appliance.
6. Fit the Natural Gas Regulator supplied in the
conversion kit.
7. Connect the gas supply to the Regulator.
8. Check for gas leaks. Do not use a naked flame to
check for gas leaks.
3. Remove the control knob, with a thin shaft blade
screwdriver down the centre of each gas valve
shaft, screw the by-pass injector fully clockwise.
4. Shut off gas supply to the appliance.
5. Disconnect gas inlet pipe from the Natural Gas
Regulator.
6. Remove the Natural Gas Regulator from the
appliance.
7. Fit the U-LPG test point inlet fitting supplied in
the conversion kit.
9. Adjust the gas pressure to 1.00 kPa.
10. Remove the control knob, with a thin shaft blade
screwdriver down the centre of each gas valve
shaft, screw the by-pass injector anti-clockwise.
Test the appliance on both high and low flame for
each burner. If the burner fails to remain alight or
the flame is not stable on the simmer setting, adjust
the by-pass screw, until flame is stable.
11. If not already removed, remove the “Only for
use with U-LPG” label adhered to the bottom panel
near the gas connection.
8. Connect the gas supply to the inlet fitting.
9. Check for gas leaks. Do not use a naked flame to
check for gas leaks.
10. Adjust the gas pressure to 2.75 kPa.
11. Test the appliance on both high and low flame
for each burner and check the gas pressure. If the
burner fails to remain alight or the flame is not
stable on the simmer setting, adjust the by-pass
screw until flame is stable.
12. If not already removed, remove the “Only for
use with Natural Gas” label adhered to the bottom
panel near the gas connection.
10
CONVERSIONS
BURNER ARRANGEMENT ON THE HOT PLATE
TABLE
BY
NORMAL
PRESSURE
INJECTOR
DIAMETER
NOMINAL HEAT
INPUT (MJ/h)
BURNERS
GAS
PASS
(1/100 mm)
N°
1
DESCRIPTION
(kPa)
(1/100 mm)
MAX.
85
85
U-LPG
NATURAL
2.75
1.00
95
155
11.9
11.9
ULTRA RAPID
SEMIRAPID
AUXILIARY
32
32
U-LPG
NATURAL
2.75
1.00
70
112
6.3
6.3
2
3
30
30
U-LPG
NATURAL
2.75
1.00
53
85
3.6
3.6
FIG. 14
11
SERVICING
WARNING:
Greasing the taps (see fig. 19 - 20)
Always disconnect the appliance from the
electricity and gas mains before proceeding
with any servicing operation.
If a tap becomes stiff to operate, it must be
immediately greased in compliance with the
following instructions:
Servicing should be carried out only by
authorised personnel.
- Remove the tap.
- Clean the cone and its housing using a cloth
soaked in diluent.
11) COMPONENTS REPLACEMENT
NOTE:
BEFORE ANY MAINTENANCE REQUIRING
REPLACEMENT OF A COMPONENT IS
- Lightly spread the cone with the relative grease.
- Fit the cone back in place, operate it several times
and then remove it again. Eliminate any excess
grease and check that the gas ducts have not
become clogged.
UNDERTAKEN
ENSURE
THAT
THE
ELECTRICAL LEAD HAS BEEN ISOLATED AND
REMOVED FROM THE POWER POINT.
- Fit all parts back in place, complying with the
demounting order in reverse.
To replace the components fit inside the hob, it is first
necessary to remove the hot palte itself from the
cabinet, to overturn it, unscrew screws “V” and to
remove part “T” (fig. 15).
After having carried out the above listed operations,
the burners (fig. 16), taps (fig. 17) and electrical
components can all be replaced (fig. 18).
- The tight closure test must be done using a foamy
liquid, the flame use is forbidden.
To facilitate the servicing technician’s task, here is a
chart with the types and sections of the powering
cables and the ratings of the electrical components.
It is advisable to change seal “D” each time a tap is
changed in order to ensure a perfect tightness.
FIG. 15
FIG. 16
FIG. 17
FIG. 18
FIG. 19
FIG. 20
12
SERVICING
CABLE TYPES AND SECTIONS
TYPE OF
HOT PLATE
TYPE OF
CABLE
SINGLE - PHASE
POWER SUPPLY
H05 RR - F
Section 3 X 0.75 mm2
Gas hot plate
ATTENTION!!!
If the power supply cable is replaced, the installer should leave the ground wire longer than the phase
conductors (fig. 21) and comply with the recommendations given in paragraph 8.
FIG. 21
13
TECHNICAL ASSISTANCE AND SPARE PARTS
MEA – BLANCO
TECHNICAL ASSISTANCE AND SPARE PARTS
NEW SOUTH WALES
SOUTH AUSTRALIA & NORTHERN TERRITORY
Head Office, Sales & Marketing Office
104 Vanessa Street
Kingsgrove NSW 2208
Agent and Sales Office
S C Lighting & Electrical Supplies
47 North Terrace
Telephone:
Facsimile:
02 9503 2888
02 9503 2810
Hackney SA 5069
Telephone:
Facsimile:
08 8362 4599
08 8362 4591
NSW Showroom*
40 Ebley Street
Bondi Junction NSW 2022
Telephone:
Service and Spare Parts
Prestige Appliance Repair Centre
02 9386 1190
02 9386 1671
Telephone:
Facsimile:
08 8352 2022
08 8352 3044
Facsimile:
Agent and Sales Office.
Hi –Performance Marketing
7 Coleman Street
Mascot NSW 2020
Telephone:
WESTERN AUSTRALIA
Agent and sales Office
Elite Appliance Marketing Pty Ltd
P.O. Box 2387, Warwick, 6024
Telephone:
Facsimile:
02 88354937
02 90048739
Facsimile:
08 9201 0311
08 9201 0366
Service and Spare Parts
All General Whitegoods Service
Service and Spare Parts
Metropolitan Appliance Repairs
Telephone:
Facsimile:
02 8788 8666
02 9756 1091
Telephone:
Facsimile:
08 9330 1724
08 9317 1296
AUSTRALIAN CAPITAL TERRITORY
TASMANIA
Service and Spare Parts
Detlevs Appliance & Electrical Care
1/88 Sheppard Street
Hume
Agent and Sales Office
Mark Pearce Agencies
23 Tranmere Road
ACT 2905
Telephone:
Facsimile:
Howrah TAS 7018
Tel/Fax: 03 6247 9215
02 6280 1033
02 6260 1035
VICTORIA
Service and Spare Parts
Electrical Equipment Service (Launceston)
State Office and Showroom*
35 Centre Road
Scoresby VIC 3179
Telephone:
Facsimile:
03 6339 3873
03 6339 4588
Telephone:
Facsimile:
03 8756 7888
03 8756 7907
Baldocks Appliance Service (Hobart)
Telephone:
Facsimile:
03 6234 5995
03 6234 8134
Service and Spare Parts
Advantage Appliances
Telephone:
03 9874 4222
03 9874 6917
Facsimile:
QUEENSLAND
BLANCO CUSTOMER SERVICE
1300 739 033
State Office and Showroom*
148 Robinson Road - East
Geebung
QLD 4034
Telephone:
Facsimile:
Website: www.meaappliances.com.au
07 3259 2555
07 3265 6933
* Showrooms open six days a week
Endeavour Appliances
Telephone:
Facsimile:
07 3872 7444
07 3852 2465
Platinum Appliance Service
Telephone:
Facsimile:
07 3862 1154
07 3862 1114
Roshad (Gold Coast)
Telephone
Facsimile
07 5535 7044
07 5535 7407
14
16
|