USER GUIDE
Concept Combo 2300
CORDED AND
DIGITAL CORDLESS
TELEPHONE
UK BTP Ver 3, Dec 07
Before operating this set,
please read these instructions carefully.
Note:This guide is for the corded part only. For instructions on how to use
the cordless part see the "Combo 2300 Cordless Handset" user guide.
Important note — emergency calls
The CC2300 cordless handset is not designed for
making emergency calls when the mains power fails.
But, if there’s a power failure, you can use the base
unit telephone to make an Emergency Call, by lifting
up the corded handset instead of using the
speakerphone.
Note: After lifting the handset you will need to wait
for several seconds to get dial tone, before keying in
the telephone number to make the call.
Also you cannot dial numbers from memories when
the mains power is off.
*** Before operating this set, please read these
instructions carefully.
If you need help …..
Binatone Helpline (for UK only)
Monday to Friday from 9:00am to 5:00pm
Tel: 0845 345 9677
**Please note that all calls are charged at local rate
Or visit our website:
http://www.binatoneonline.com
Unpacking your CC2300 system
In the box, you will find:
Ƶ the base unit telephone
Ƶ a telephone line cable for the base unit
Ƶ a mains power adapter for the base unit
Ƶ the cordless handset (up to five, depending on
which CC2300 system you’ve bought)
Ƶ two 1.2V 550mA rechargeable batteries and a
battery compartment cover for each handset
Ƶ up to five charger pods, each with a mains power
supply for multi handset systems
Ƶ two user guides, one for the corded phone and one
for the cordless handset.
Keep the packaging materials in a safe place in case
you later need to transport the unit.
Keep your sales (till) receipt, which is your
guarantee.
Where to find it
Delete(DEL)
Press to delete
messages, memos,
stored numbers or
Caller Display records.
Up-Down(CDS)
Intercom
Press to make an intercom
call or to transfer a call
Press to access the
Caller display records
and scroll through them
LCD Display
Press to change earpiece
speakerphone volume
Press to scroll through the
lists and menu options
Phonebook/Back
/C
Press to access phonebook
records
Press to exit present menu
One-touch Memory
M1, M2, M3
Menu/Ok
Press to access menu
Press as “OK” key to
confirm your operation
Press to call numbers
stored on One Touch
memory
/P
Press to redial the
last number
Press while dialing a
number to insert a pause
Speakerphone
Press to call or answer a call
by using the speakerphone.
MUTE
SOS Call
Press to mute/
un-mute microphone
during a call
Press and hold for 2 seconds
to activate the SOS call
Microphone
For speakerphone
R(Recall)
You may need this function
if your phone is connected
to a PBX, or if you use BT
and answering
machine recording.
Calling Features.
Important:
When the instruction simply say ‘press’ a button, this means you should press it briefly then
release it.
When the instruction say ‘press and hold’ a button, this means you should keep it pressed
until the display changes or you hear a tone.
Binatone Help Line : 0845 345 9677
1
What's on the display?
The display of your telephone contains one line with the Time/Date
and Icons, one line of numbers and one line of text.
Number field: shows the telephone
numbers
Character field: shows the Menu,
name and status of a call
What do the symbols mean?
Talk
xꢀ This will display when the user picks up the
handset
Ring Off
xꢀ This will display when the ringer is set to
OFF
Phonebook
Voicemail
xꢀ This will display when you are in the
phonebook menu
xꢀ
This will display when you have a new Voice
Mail message. (This is a caller id service and
is not usually available from UK network
providers.)
Repeat CID
xꢀ This will display when the same caller has
called more than once
New CID
xꢀ This will display when there is a new CID
entry or if one is being viewed
Sequence
xꢀ Indicates the sequence number of the CID
record
Hands free/speakerphone
xꢀ This will display when the speakerphone is
in use
A.M.
P.M.
xꢀ This will display if it is A.M., in the 12 hour
clock mode
xꢀ This is display if it is P.M., in the 12 hour
clock mode
Binatone Help Line : 0845 345 9677
2
Contents
Page
Page
1
Where to find it
xꢀ To delete a contact in the phonebook 13
xꢀ To delete all contacts in your phonebook
14
What’s on the display?
2
xꢀ What the symbols mean?
2
xꢀ To edit a contact in your phonebook 14
xꢀ To store a last number redial in your
Read First before Use
xꢀ Choosing a site for base unit and
charger pod
xꢀ Mains power connection
xꢀ If you have a broadband line
5
15
phonebook
xꢀ Making calls from the phonebook
16
5
5
5
xꢀ Reviewing phonebook memory status16
16
16
16
xꢀ Direct Memory Call
xꢀ To Store the telephone number
xꢀ To Speed-Dial the telephone number
Installation and Set-up
6
xꢀ Choose a suitable site for the base unit
6
Caller Display (CDS)/Caller ID (CID) 17
xꢀ New CID log
17
17
18
18
xꢀ Connect the mains power lead and the
telephone line cord into the base unit 6
xꢀ Plug the main adaptor into your wall
xꢀ To review the CID list
xꢀ To delete a Caller ID record
xꢀ To delete all Caller ID records
xꢀ To Store a Caller ID contact in
phonebook
socket
6
xꢀ Connect the base unit to the telephone
18
line
6
Ringer volume, and melody
xꢀ To change ringer volume
19
19
Desk/Wall mount installation
7
7
7
Desk Mount
xꢀ
xꢀ Wall Mount
Using multi-handset
21
Basic settings
9
xꢀ To set Date and Time
9
xꢀ To make intercom calls
xꢀ To Transfer intercom call
xꢀ To set up a three-way conference
21
21
22
Making and answering calls
xꢀ To make call
xꢀ To make a call from redial list
10
10
10
SOS call function
25
xꢀ To make a call from caller display (CID)
xꢀ How SOS call functipn works
xꢀ How to terminate SOS call function
25
25
list
10
10
xꢀ To answer a call
xꢀ To Set SOS number
25
xꢀ To Mute or un-mute the microphone 11
xꢀ To change the earpiece or speakerphone
volume during a call
11
xꢀ Emergency call without mains power 11
Memory/Phonebook management
12
xꢀ To create a contact in your phonebook
13
Binatone Help Line : 0845 345 9677
3
Advanced use of your Phone
26
xꢀ To Turn key tones on/off
26
26
27
27
28
xꢀ To Set flash (Recall) time
xꢀ To Set Dialling Mode (Tone/Pulse)
xꢀ To Set Base to default settings
xꢀ To Change the PIN code
Troubleshooting
29
31
31
32
33
Cleaning and Care
Declaration of Conformity
Guarantee and Service
Technical Details
Connection and conditions for use.
You can connect your Concept Combo 2300 to a direct exchange line (DEL) - a line
connected to a local exchange, with its own phone number; to an extension on an approved
compatible PBX. Do not connect the Concept Combo 2300 as an extension to a payphone.
The ringer equivalence numbers (RENs) of all instruments (phones, fax machines, etc.)
connected to an exchange line must not add up to more than 4 - otherwise, one or more
of them may not ring and/or answer calls correctly. The Concept Combo 2300 has a
REN of 1, and most other telephones have a REN of 1 unless marked otherwise.
Binatone Help Line : 0845 345 9677
4
Read First Before Use
Choosing a site for the base unit and charger pod
The base unit and charger pod(s) should be placed on a level surface, in a position where:
xꢀ the mains adapter plug will reach an easily accessible 230-VAC switched mains
supply socket - never try to lengthen the mains power cable
xꢀ the base unit's telephone line cable will reach your telephone line socket or
extension socket
xꢀ it is not close to a sink, bath or shower, or anywhere else where it might get wet
xꢀ it is not close to other electrical equipment - fridges, washing machines,
microwave ovens, fluorescent lights, televisions etc.
xꢀ if the base comes into contact with liquids, disconnect it promptly and use a soft
cloth to dry it; if you believe that the liquid has seeped into the unit, do not
reconnect the base station. Contact the Binatone helpline.
xꢀ it is away from hot, humid conditions and strong sunlight
Mains power connection
IMPORTANT - The CC2300 base unit must be used with the mains adapter supplied
with the unit.
Using any other adapter will result in non-compliance with EN60950, and will
invalidate any approval given to this apparatus.
If you have a Broadband line
If you connect your telephone to a line with a broadband connection, you will need to
insert a micro-filter between the telephone and the telephone line; otherwise you may
get interference between the telephone and the broadband, which could cause
problems.
In a home with broadband, every telephone must have a micro-filter connected, not
just the one at the telephone point that your modem is connected to. If you need more
broadband micro-filters, contact your broadband supplier.
Binatone Help Line : 0845 345 9677
5
Installation and Set-up
1/ Choose a suitable site for the
base unit (see page 5)
2/ Connect the mains power lead
and the telephone line cord into the
base unit
Plug one end of the telephone line
cord into the jack on the back of the
base (the other end will plug into the
telephone wall socket later)
See the note
on page 5
3/ Plug the mains adaptor into your wall
socket. If you have one or more charger pods,
plug the mains adaptors accordingly
Make sure that the 230VAC, 50hz mains socket is switched OFF
when you plug the mains adapter into the socket.
See the note
on page 5
4/ Connect the base unit to the telephone line
Insert the telephone line plug into the socket then
switch mains power back ON.
—
Make sure the mains socket is switched on
the phone won’t work without electrical power
Binatone Help Line : 0845 345 9677
6
Desk/Wall mount installation
Desk Mount
To place the CC2300 on a desk, connect
the stand to the bottom of the phone in the
slots near the rear of the base as shown below.
Insert the rigid clips of the stand into the slots
on the bottom of the phone (nearer the centre
of the base ). Press down firmly until the
flexible clips clicks into place.
To remove the stand, (1) pinch the flexible
clips, (2) pull back the stand, and then (3)
slide up and forward as shown below.
Wall Mount
To place the CC2300 on a wall, connect the
stand to the bottom of the phone in the slots
near the front of the base as shown below.
Binatone Help Line : 0845 345 9677
7
Desk/Wall mounting continued...
Insert the rigid clips of the stand into the slots
on the bottom of the phone (nearer the centre
of the base). Press down firmly until the flexible
clips clicks into place.
To remove the stand, (1) pinch the flexible
clips, (2) pull back the stand, and then (3)
slide up and forward as shown below.
Mark two points on the wall that are 77 mm
apart to lay the fixing centers as shown below.
BE CAREFULto check that there are no
electrical wires hidden in the wall. Fix two screws
at the marked locations, leaving approximately
7mm between the wall and the the screw head.
Hang the telephone on the screws using the
wall mount slots. You may need to remove the
telephone from the wall and tighten the screws
so that the telephone is securely fixed and does
not wobble. Place the Handset on the cradle with
the parking hook on the cradle arranged to fit
in the parking recess under the earpiece on
the Handset.
Binatone Help Line : 0845 345 9677
8
Basic settings
To set Date and Time
Note:If you subscribe to Caller Display (see page 17) your SC3410 time and date settings
will be automatically updated by the network when you receive an incoming call.
The Caller Display service only sends the month and date, not the year, so you may still
need to set the year, as this is used to calculate the day for the answering machine time stamp.
If the time and date are set on the cordless handset, it will automatically be set on
the base unit, and vice-versa.
The format for the date is YYYY-MM-DD, and the time is HH:MM in 12 hour format
Press the MENU/OK button.
Then press the UP or DOWN button until "SETTINGS" is displayed.
or
or
Then press the MENU/OK to confirm.
The display will show “DELETE HS”,
Press the UP or DOWN button until "DATE & TIME" is displayed.
Then press the MENU/OK to confirm.
The 'year' will be flashing.
or
or
Press the UP or DOWN button to set the year.
Press the MENU/OK to confirm.
The 'month' will be flashing.
Press the
or DOWN button to set the month
UP
Press the
to confirm.
MENU/OK
The 'date' will be flashing.
or
or
or
Press the UP or DOWN button to set the date
Press the MENU/OK to confirm.
The 'hour' will be flashing.
Press the UP or DOWN button to set the hour, including the AM/PM setting
Press the MENU/OK to confirm.
The 'minutes' will be flashing.
Press the UP or DOWN button to set the minutes.
Press the MENU/OK to confirm.
Press the "PHONEBOOK" button to return to the previous menu.
You will hear a beep and the display will show "DATE & TIME".
Press the “PHONEBOOK” button to return to the previous menu.
Binatone Help Line : 0845 345 9677
9
Making and answering calls
To make a call
Pick up the handset and the TALK
SPEAKERPHONE button and the SPEAKERPHONE icon
icon will appear,or press
will appear.
a call
Also the display will show “LINE IN USE”.
Use the keypad to enter the number you wish to dial.
When you have finished the call place the handset back on the base.
You can also make a call by using the Pre-Dialling function:
Dial the required telephone number first, and if you make a mistake you can
correct it by using the DEL button to delete digits and then add the right ones.
Pick up the handset or press the Speakerphone button.
The number will be dialled out automatically using the handset or
speakerphone mode selected.
* To insert a pause in the dialling sequence, press the RD/P button, which will then show
a P in the number.
To make a call from the redial list
The phone remembers the last 10 dialled numbers. The list is in order, with the most recent
message at the top.
a call from the redial list
Press the REDIAL/PAUSE button to view the redial list.
Press the UP or DOWN button until you see the number of the person you want to call.
or
Press the SPEAKERPHONE button or pick up the handset to make the call.
To make a call from Caller Display (CID) list
Press the UP or DOWN button to show the first entry in the CID list.
If your list is empty, the display will show “EMPTY”.
Press the UP or DOWN button until you see the number of the person you
want to call.
or
Press the SPEAKERPHONE button or pick up the handset to make the call.
To answer a call
When the phone rings:
Pick up the handset or press the SPEAKERPHONE button to answer the call.
Binatone Help Line : 0845 345 9677
10
To Mute or Un-mute the microphone
During a call press the MENU/OK button and the display will show
“CALL MUTED”.
To un-mute, press the MENU/OK button and the display will show
“LINE IN USE”.
To change the earpiece or speakerphone volume during a call
t
During a call press the UP button to increase or DOWN button to decrease he
Volume.
or
EMERGENCY CALL WITHOUT MAINS POWER
The CC2300 corded base unit can make an emergency call with the corded handset
when the mains AC power is disconnected.
xꢀ Pick up the corded handset.
After lifting the handset you will need to wait for several seconds to get dial tone,
before keying in the telephone number to make the call.
It is not possible to dial numbers from memories when the mains power is off.
xꢀ When the mains power is off, you can also answer an incoming call with the
corded handset.
When the phone rings, pick up the corded handset. After lifting the handset you
will need to wait for several seconds before you can hear the calling person's voice
or before they can hear you.
Binatone Help Line : 0845 345 9677
11
Memory/Phonebook management
How to enter characters?
To enter the characters, press the button
where you see the character e.g. if you want to
insert the letter ‘A’ you press ‘2’
if you want to
insert the letter ‘B’ you press twice and for ‘C’,
three times etc. If you want to insert ‘AA’ then
you will have to wait for the first ‘A’ to stop
flashing then insert the second ‘A’. Press
DEL
twice for space,
to delete single characters
DEL
and press and hold
to delete the whole text.
Telephone Keypad characters
1st 2nd 3rd 4th 5th 6th 7th 8th 9th 10th 11th 12th 13th 14th
?
!
_
B
E
H
K
N
Q
U
X
0
,
C
F
I
?
2
3
4
5
6
S
8
Z
-
!
(
)
:
;
.
1
A
”
’
á
Ç
Æ
D
G
í
J
L
~
~
M
O
R
V
Y
+
N
P
7
ú
T
W
space
9
@
=
/
\
[
]
*
#
Binatone Help Line : 0845 345 9677
12
To create a contact in your phonebook
The Phonebook can store up to 150 names (maximum 12 characters) and numbers
(maximum 20 digits) in the memory.
Also, you can select a different ringer melody for each entry, but this will only work if
you subscribe to CID (see page 17).
Press the MENU/OK button, to see “PHONE BOOK”.
Press the MENU/OK button, to see “LIST”.
Press the DOWN button, to see "NEW ENTRY".
Press the MENU/OK button and the display will show a flashing bar at the
beginning of the name position.
Key in the name using the digit keys (maximum 12 characters). If you
make any mistakes press DELETE button to delete.
When you have finished press the MENU/OK button to confirm, and the display
will move the flashing bar to the beginning of the number position.
Key in the number using the digit keys (maximum 20 digits).
If you make any mistakes use the DELETE button to delete.
Press the MENU/OK button to confirm and the display will show
“MELODY 1”.
Use the UP or DOWN buttons to scroll through the melodies.
(there are 10 melodies to choose from).
or
Press the MENU/OK button to confirm your selection. You will hear
a confirmation tone, and the display will return to “NEW ENTRY”.
*If there is no more space in the phonebook, “MEMORY FULL” will appear on the
display.
To delete a contact in your phonebook
Press the MENU/OK button, to see “PHONE BOOK”.
Press the MENU/OK button, to see "LIST".
Press the DOWN button repeatedly until you see “DEL RECORD”.
Press the MENU/OK button. The display will show the first name and
number in your phonebook.
Binatone Help Line : 0845 345 9677
13
Use the UP or DOWN buttons to scroll through the list
until you see the contact you want to delete.
or
Press the MENU/OK button and the display will show “CONFIRM?”.
Press the MENU/OK button to confirm if you really want to delete this
entry, or press the PHONEBOOK/CANCEL to save the contact.
In either case, the display will return to the previous menu option.
To delete all contacts in your phonebook
Press the MENU/OK button, to see “PHONE BOOK”.
Press the MENU/OK button, to see "LIST".
Press the DOWN button repeatedly until you see "DELETE ALL".
Press the MENU/OK button and the display will show “CONFIRM?”.
Press the MENU/OK to confirm,
or press the PHONEBOOK/CANCEL button to save the contacts.
In either case, the display will return to the previous menu option.
To edit a contact in your phonebook
Press the MENU/OK button, to see “PHONE BOOK”.
Press the MENU/OK.
Press the DOWN button repeatedly until you see “EDIT RECORD”.
Press the MENU/OK button and the display will show the first
name and number in your phonebook.
Scroll UP or DOWN until you see the contact you want to edit.
or
Then press the MENU/OK button and a flashing bar will appear at
the end of the name.
Use the keypad to enter characters or DELETE button to delete.
Press the MENU/OK button to confirm, and the display will move the
flashing bar to the end of the number position.
Use the keypad to enter digits or the DELETE button to delete.
Binatone Help Line : 0845 345 9677
14
Once you have finished press MENU/OK button to confirm and the
display will show “MELODY 1”.
Scroll UP or DOWN to select a melody..
or
Then press the MENU/OK button to confirm, and the
display will go back to the previous menu.
To store a last number redial in your phonebook
Press the REDIAL/PAUSE button to review the last number redial list.
or
Scroll UP or DOWN to find the number you want to store.
Press the MENU/OK button. Then the display will show "ADD TO PB?".
Press the MENU/OK button to confirm, and the display will show a flashing
bar at the beginning of the name position.
Key in the name for this redial number into the phonebook.
Press the MENU/OK button to confirm the name.
The display will move the flashing bar to the end of the number position.
If the number needs modifying use the keypad to enter digits or
the DELETE button to delete.
Press the MENU/OK button to confirm the number, and
the display will show "MELODY 1".
or
Use the UP or DOWN buttons to scroll through the melodies.
Press the MENU/OK button to confirm your selection.
You will hear a confirmation tone, and the display will return to the last
number redial list.
Binatone Help Line : 0845 345 9677
15
Making calls from the phonebook
Either press the PHONEBOOK/CANCEL button once, or the MENU/OK
button three times, and you will see the 1st number and name in the phonebook.
Scroll UP or DOWN to select the name and number of the person
you want to call.
or
Note: For a short-cut to finding the name, you can press the digit buttons to go
directly to the first entry beginning with the corresponding letters of that key,
and then scroll from there.
Then pick up the handset or press the SPEAKERPHONE button to make the call.
Reviewing phonebook memory status
This allows you to review how many records in the phonebook are occupied.
The phonebook allows up to 150 names and numbers.
Press the MENU/OK button, to see “PHONE BOOK”.
Press the MENU/OK button, and then
press the UP or DOWN buttons until you see "MEM STATUS".
Press the MENU/OK. Then the display will show the phonebook
memory space available e.g. if you have saved 30 names and numbers in
your phonebook, it would display 30/150.
Press the PHONE BOOK/BACK until you return to idle mode.
Direct Memory Call
There are three Direct Memory buttons M1 and M2 and M3 on the corded base.
To Store the telephone number
In idle mode, enter the telephone number you want to store.
Press and hold M1 key for more than 2 econds, until you hear the confirmation
tone to indicate the number has been stored.
To Speed-Dial the telephone number
In idle mode, briefly press M1 and the unit will automatically dial out the
telephone number in speakerphone mode.
Binatone Help Line : 0845 345 9677
16
Caller Display (CDS) / Caller ID (CID)
To subscribe to this feature, you need to contact your service provider, and there may be
a charge for this service . Caller Display lets you see the phone numbers of your callers on
the display, before you answer.
The base and each handset will store its own CID list independently. Both answered and
unanswered calls are stored, up to a maximum of 20 calls. When the caller display list is full,
any new caller display entry will replace the oldest record.
The base and each handset will store its own CID list independently. Both answered and
unanswered calls are stored, up to a maximum of 20 calls. When the caller display list is
full, any new caller display entry will replace the oldest record.
The caller display information includes:
- the caller's number (up to 20 digits)
- the date and time of the call
- the caller's name (up to 12 characters) if the incoming number matches an entry
in the Phonebook
Note: it will also display the caller's name if the network sends it, but this is not normally
available in the UK.
New CID log
If you receive a new call, the display will show the
of the caller.
icon with the name and number
If there are no items on the CID list, the display will show NO CALLS.
The display may also show the following:
UNAVAILABLE – if the number of the caller is unavailable, e.g. from an international call.
WITHHELD – if the call is from someone who has withheld their number, e.g. by dialling 141.
To review the CID list
.
Press the MENU/OK button, to see PHONEBOOK
Press the DOWN button, to see "CALL LOG".
Press the MENU/OK button, to see “RECEIVED”.
Press the MENU/OK button, to see the most recent record in the CID list.
icon will
Press the UP or DOWN buttons to scroll through the CID list. The NEW
or
or
be displayed in the idle screen until all new calls have been viewed in the CID list.
Note: To go directly to the first record of the CID list,press the UP or DOWN
buttons in standby mode.
*If you wish to call directly from the CID list, press the SPEAKERPHONE button or lift up
the handset to dial the number automatically.
Binatone Help Line : 0845 345 9677
17
To d
record
To delete a Caller ID record
Repeat the steps above to review the CID list, and to locate
the record you want to delete.
Press the MENU/OK button, to see ADD to PB?
Press the DOWN button, to see DELETE?
Press the MENU/OK button twice, you will hear the completion tone
and the display will return to the Caller ID list.
To delete all Caller ID records
Repeat the steps above to review the CID list.
Press the MENU/OK button, to see ADD to PB?
Press the DOWN button twice to see DELETE ALL?
Press the MENU/OK button twice, you will hear the completion tone
and the display will show EMPTY
.
To store a Caller ID contact in the phonebook
Repeat the steps above to review the CID list, and to locate the record you want to
store in the phonebook.
Press the MENU/OK button to see “ADD TO PB ?”.
Press the MENU/OK button to confirm, and the display will show a flashing bar at
the beginning of the name position
Enter name using keypad.
Press the MENU/OK button to confirm the name.
The display will move the flashing bar to the end of the number position.
If the number needs modifying use the keypad to enter digits or
the DELETE button to delete.
Press the MENU/OK button to confirm the number, and the
display will show "MELODY 1".
Use the UP or DOWN buttons to scroll through the melodies.
or
Press the MENU/OK button to confirm your selection.
You will hear a confirmation tone, and the display will return to the CID list.
Binatone Help Line : 0845 345 9677
18
Ringer volume, melody
To change ringer volume
You can adjust the volume level of the intercom ringer (INT RING) and the external call
ringer (EXT RING) independently, with settings from 1 (quietest) to 5 (loudest), or turned OFF.
Press the MENU/OK button.
Scroll DOWN until you see “SETTINGS”.
Then press the MENU/OK button.
Scroll DOWN until you see “RING SETUP”.
Press the MENU/OK button. Then it will display “INT RING” or scroll
DOWN to select “EXT RING”.
Press the MENU/OK button. The display will show “MELODY”.
Scroll DOWN until you see “VOLUME”.
Then press the MENU/OK button to select and the display will show
“VOLUME 2”.
Press the UP or DOWN button to scroll through the volume settings
(from OFF, 1 to 5).
or
Then press the MENU/OK button to confirm the setting
Press the PHONEBOOK/BACK button to return to the previous menu
To change ringer melody
There are 10 base ringer melodies from 1 to 10
Press the MENU/OK button.
Scroll DOWN until you see “SETTINGS”.
Binatone Help Line : 0845 345 9677
19
Then press the MENU/OK button.
Scroll DOWN until yiu see “RING SETUP”.
Press the MENU/OK button. Then it will display “INT RING” or scroll
DOWN to select “EXT RING”.
Press the MENU/OK button. The display will show “MELODY”.
Then press the MENU/OK button to select and the display will show
“MELODY 1”.
or
Press the UP or DOWN button to scroll through the Melody list (from 1 to 10).
Then press the MENU/OK button to confirm the setting.
Press the PHONEBOOK/CANCEL button to return to the previous menu.
Binatone Help Line : 0845 345 9677
20
Using a multi-handset system
To Make Intercom calls
Press the INTERCOM button. If you have only one cordless handset registered
to the base, the display will show "CALLING HS1" and the base will beep.
If you have more than one handset registered to the base, the display will
show "HS?" with the registered handset numbers above, and the base will
output a continuous beep, until you press the number for the handset you
want to intercom. Then the display will change, for example, to "CALLING HS2",
if it is handset 2 that is being called.
If you enter a number that is not available the base will return to idle mode.
If you do not enter any number for 1 minute the handset will return to idle mode.
The handset being called will ring with its selected melody and display
"BASE CALLING".
To cancel the intercom call press the INTERCOM button again.
Receiving an intercom call from a cordless handset.
When the phone rings and the display shows "HS 1 CALLING", you can answer
the call by pressing the SPEAKERPHONE button or picking up the handset.
If you want to end the intercom, press the SPEAKERPHONE button or
replace the handset.
To Transfer intercom call
During a call, it is possible to transfer a call to another handset.
During an external call, if you want to transfer the call to a cordless handset,
press the INTERCOM button. The external call will be put on hold.
If the base has only one cordless handset registered it will immediately start calling
that handset, but if more than one handset is registered enter the number for the
handset you want to transfer the call to.
[1][2]…
When the handset answers the intercom call, simply hang-up at the base to
transfer the call.
Binatone Help Line : 0845 345 9677
21
If the handset does not answer within 30 seconds, the transfer will be cancelled and
the external call reconnected to the base.
Alternatively, once the intercom ringing starts and the display shows, for example,
"CALLING HS1", you can hang-up the phone to transfer the call automatically.
The display will change to "TRANSFER HS1". The called handset will ring for 1
minute, but if it does not answer, both the base and handset will ring for another
minute.If neither answers, the ringing will stop and the external call will be released.
Receiving a transfer call from a cordless handset.
When you have an intercom call transfer your handset will ring and the
.
display will show “HS 1 CALLING”
To answer the call, pick up the handset and you will be connected.
If you want to end the intercom transfer, hang-up the phone.
To Set up a three-way conference
During an external call it is possible to conference in another handset.
During a call, press INTERCOM button and enter the number of the handset
you want to connect to, by using the keypad.
The display will show the handset name you have entered and the other
handset will ring. If the number you have entered is not available, you will
hear an ERROR tone and the call will be returned to the original handset.
If you do not enter any number within 30seconds the call will also be
returned to the original handset.
Once the other handset answers the call, press STAR( ) button and the display
will change from "INTERCOM" to "CONFERENCE", and both the base and the
cordless handset will be connected to the external call.
When either the base or the handset hangs up, the other will still be
connected to the external call.
Receiving a conference call.
When you receive intercom ringing from a handset, answer the call and the
display will show "INTERCOM".
Then wait for the other handset to initiate the three-way conference call.
Either handset can just hang-up to end the call and the other handset will
still be connected.
Binatone Help Line : 0845 345 9677
22
Page / locate a handest
Press the INTERCOM button. If you have only one cordless handset registered
to the base, the display will show "CALLING HS1" and the base will beep.
If you have more than one handset registered to the base, the display will
show "HS?" with the registered handset numbers above, and the base will
output a continuous beep, until you press the number for the handset you
want to page. Then the display will change, for example, to "CALLING HS2",
if it is handset 2 that is being paged.
If you enter a number that is not available the base will return to idle mode.
If you do not enter any number for 1 minute the handset will return to idle mode.
Handset registration
To register new handsets to the base:
The handset(s) supplied with your CC2310 system are already registered
!
Ð the first one as handset number 1, the second as number 2...etc
You don't need to re-register them, unless you have a problem.
To check whether a handset is registered, make sure mains power to the base
unit is switched on and the handset is within range. The handset's display
should show its number, and the `signal level' symbol on the display should
show three bars. If the display shows "UNREGISTERED" , you need to re-register
the handset using the following process:
You need to operate the base and handset together:
1. On the handset, press the MENU/OK button to see "PHONEBOOK".
2. Press the UP button twice to see "REGISTRATION".
3. Press the MENU/OK button to see "BASE 1".
If the handset already has a registration to a base there is a "+" on the right side of
the display, and you should choose another base number if you don't want to
lose that one.
Binatone Help Line : 0845 345 9677
23
4. Press the DOWN button to select a base number (BASE 1, 2,3 or 4)
5. Press the MENU/OK button to see "PIN ?"
Key in the 4 digit PIN code for the base - the CC2300 default PIN code is 0000
6. Press the MENU/OK button to confirm, and the
display will flash
"SEARCHING 1" (or 2,3,4)
7. At the same time, on the base, press the MENU/OK button to see
"PHONEBOOK"
8. Press the UP button tweice to see
"REGISTRATION"
9. Press the MENU/OK button to see
"SEARCHING" flash on base display
After a short delay, if the registration is successful, there will be a
confirmation beep, and the Handset display will go back to idle mode with
tnhuemnbeewr shhaonwdnse(et.gu.pHaS1th, rHeSe-2w).aTyhceobnafeserednicspelay will also go back to
idle mode.
To de-register a handset
You may need to do this if you need to replace a faulty handset. Call the Binatone help
line if you need more advice.
To de-register a handset using the CC2300 base menu
With the base in idle mode:
1. Press the MENU/OK button to see "PHONEBOOK"
2 .Press the DOWN button twice to see"SETTINGS"
3. Press the MENU/OK button to see "DELETE HS"
4. Press the MENU/OK button to see " HS 1 " (or 2,3, 4)
Press UP or DOWN button to select the handset you want to de-register.
5. Press the MENU/OK button to confirm, and the selected handset will be
de-registered. (The display on the handset that has been deleted
will show "UNREGISTERED".)
Press the PHONEBOOK/BACK button to return to the previous menu
*
at any time.
Note: Handsets can also be de-registered using another cordless handset,
as described in the cordless handset user guide.
Binatone Help Line : 0845 345 9677
24
SOS call function
The SOS call function is very useful for people at home to make an emergency
call to ask for help from their relatives, police, doctor, etc.
How SOS call function works
xꢀ Press and hold SOS button
for more than 2 seconds.
The line is automatically seized and dials to each of the pre-stored SOS numbers,
xꢀ
starting with the first. and it will wait for 1 minute and then drop the call.
xꢀ The line is automatically seized and dials to each of the pre-stored SOS numbers,
will wait for 1 minute and then drop the call.
xꢀ Then it makes another call to the second SOS number, if programmed, and sends the
lannouncement to ine for another 1 min.
xꢀ Finally it will make another call to the third SOS number, if programmed,
and send the announcement to line for another 1 minute.
How to terminate SOS call function
xꢀ When the SOS call function is active, you can only terminate this function by lifting
up the corded handset on the base. It can not be terminated by using any buttons
on the cordless handset.
To Set SOS numbers
User is allowed to set up to 3 SOS numbers and 1 SOS voice recording.
Press the MENU/OK/MUTE. Scroll DOWN until you see “SOS SETTINGS”.
Press the MENU/OK/MUTE and you will see “SOS NUMBER”.
Press the MENU/OK/MUTE and you will see “SOS NUMBER 1”.
or
Scroll UP or DOWN to select SOS NUMBER 1 to 3.
Then press the MENU/OK/MUTE to select the one you want to program.
Enter the phone number.
Then press the MENU/OK/MUTE. You will hear a beep and the number is
saved.
If you want to save more SOS numbers, press the DOWN to select the next
location you want to program,and repeat above steps.
Press the PHONE BOOK/BACK until you return to idle mode
.
Binatone Help Line : 0845 345 9677
25
Advanced use of your phone
To Turn on/off key tone
Press the MENU/OK. Scroll DOWN until you see “SETTINGS”.
Press the MENU/OK and then you will see “DELETE HS”.
Then scroll DOWN until you see “KEY TONE”.
Press the MENU/OK and the display will show “ON”.
or
Press the UP or DOWN button to select ON or OFF on the display.
Press the MENU/OK button to confirm the option, and you will
hear the confirmation beeps.
The display will return to "KEY TONE".
Press the PHONE BOOK/BACK until you return to idle mode.
To Set Flash (Recall) time
The Recall (also called Flash) may be needed if you use BT calling functions or are
connected to a PABX.
The default setting of this CC2300 telephone is 100ms, and normally this
will be correct for the UK.
However, if necessary, you can select from 3 flash times: 100ms, 250ms and 600ms
to meet your telephone line or PABX requirement.
Press the MENU/OK. Scroll DOWN until you see “SETTINGS”.
Press the MENU/OK and then you will see “DELETE HS”.
Scroll DOWN until you see “FLASH TIME”.
Press the MENU/OK and the display will show the current setting of
the Flash time, e.g. "100" ms.
or
Press the UP or DOWN button to show the flash time you want on the display.
Press the MENU/OK button to confirm the option, and you will hear
the confirmation beeps. The display will return to "FLASH TIME".
until you return to idle mode.
Press the PHONE BOOK/BACK
Binatone Help Line : 0845 345 9677
26
To Set Dialling Mode (Tone/Pulse)
The default setting of this CC2300 telephone is TONE (also called Touch Tone, MF or DTMF),
and normally this will be correct for the UK, so will not need to be changed.
However, for some old telephone lines or PABX systems you may need to change
the dialling mode from Tone to Pulse.
Press the MENU/OK . Scroll DOWN until you see “SETTINGS”.
Press the MENU/OK and then you will see “DELETE HS”.
Scroll DOWN until you see “DIAL MODE”. Press the MENU/OK and the
display will show the current setting of Dialling Mode e.g. “TONE” or
“PULSE”.
or
Press the UP or DOWN button to show the dialling mode you want on the display.
Press the MENU/OK button to confirm the option, and you will hear the
confirmation beeps. The display will return to "DIAL MODE" .
Press the PHONE BOOK/BACK until you return to idle mode.
To Set Base to default settings
This allows you to restore base settings to their default settings:
Ext Ringer Melody = 1
Dial Mode = TONE
Int Ringer Volume = 5
Flash Time = 100ms
PIN CODE = 0000
Ext Ringer Volume = 5
Int Ringer Melody = 2
Key Tone = ON
Language = ENGLISH
The Caller Display (CID) and Redial lists will be erased, but the Phonebook memories
and TAM settings will remain unchanged.
Press the MENU/OK scroll DOWN until you see SETTINGS.
Press the MENU/OK then scroll DOWN until you see “BS DEFAULT”.
Press the MENU/OK and the display will show “PIN ?”.
Enter the PIN code using the keypad. (Default PIN is 0000)
Press the MENU/OK and you will hear the confirmation beeps and
the display will return to idle mode.
Binatone Help Line : 0845 345 9677
27
To Change the PIN code
Some functions (including handset registration) require a PIN code. The default PIN is 0000
but you are able to change to your personal 4-digit PIN.
Press the MENU/OK button.
Then scroll DOWN until you see “SETTINGS”.
Then press the MENU/OK button.
Then scroll DOWN until you see “MODIFY PIN”.
Press the MENU/OK button and the display will show
“PIN ?”.
Enter the PIN code using the keypad (if you haven’t changed it, the
default PIN is 0000).
Press the MENU/OK button and the display will show
“NEW PIN”.
Use the keypad to enter the new PIN (4 digits from 0-9).
Press the MENU/OK button to confirm and the display will show
“REPEAT”.
Use the keypad to enter the new PIN again and
press the MENU/OK button to confirm.
You will hear the confirmation beeps and the display will return to "MODIFY PIN".
Press the PHONE BOOK/BACK until you return to idle mode.
* If you enter the wrong PIN at any time you will hear an error tone and the display will return
to the previous menu.
Binatone Help Line : 0845 345 9677
28
Troubleshooting
ALWAYS check
first that:
xꢀ You have followed all the steps listed onpages 5 & 6 to install
and set up your CC2300
xꢀ All connectors are firmly inserted in their sockets
xꢀ Mains power to the base unit is switched on at the socket
xꢀ The handset’s batteries are correctly and securely installed
and are not run down
Everyday use
“I cannot make or
answer calls”
xꢀ Check that the base unit’s mains power adapter is plugged
in and power is switched on. The base unit needs mains
power for normal operation of the phone – only the basic
handset calling works without mains power.
xꢀ Make sure you are using the telephone line cable supplied
with your CC2300. Other telephone line cables might
not work.
xꢀ Switch off power at the mains socket, wait for a few
seconds and then switch back on. This may solve the
problem.
“I cannot make a
call”
xꢀ Only one handset (or the base unit) can be connected to the
outside line at once. If a cordless handset is already using
the line, you need to wait until it’s finished its call.
“The phone does
not ring”
xꢀ Check that the base unit’s mains power adapter is plugged
in and power is switched on. The base unit needs mains
power for normal operation of the phone – only the basic
handset calling works without mains power.
xꢀ Make sure you are using the telephone line cable that was
supplied with your CC2300. Other telephone line
cables might not work
Binatone Help Line : 0845 345 9677
29
“The Caller Display
feature isn’t
working”
xꢀ You need to subscribe to the Caller Display feature from
your network service provider. You should find contact
details on your phone bill.
xꢀ The caller may have withheld their number by dialling 141.
Or they may be calling from a network that does not transmit
the caller’s number (e.g. it may be an international call.)
“When I try to
make a call, I hear
Busy tone.”
xꢀ If you’re using a CC2300 multi-handset system, check
whether other handsets are already on a call.
“The volume in the
earpiece is low
xꢀ Make sure you’re holding the earpiece correctly over your
ear.
when I’m on a call”
xꢀ Adjust the volume using the UP/DOWN button.
Intercom and transfer
“I can’t transfer a
call”
xꢀ Make sure the other handset is in range of the base unit.
xꢀ Make sure you are dialling the correct number for the other
handset.
If the fault persists…
xꢀ Disconnect all other instruments connected to the same
line as the CC2300 and try to make a call
xꢀ Disconnect the base unit from the telephone line and plug
a different phone into the master telephone socket. Try
making a call. If this works, the line is OK.
xꢀ If the call does not work, and you are using a two-way
socket adapter, remove it and plug a telephone directly into
the socket. If the call now works, the adapter may be faulty.
xꢀ If you cannot make a call, the fault may be on the exchange
line. Contact the service provider (the BT engineers on 151
for UK only, or your cable company).
xꢀ If you still cannot identify the cause of the problem, contact
the Binatone on 0845 345 9677 (UK only).
Binatone Help Line : 0845 345 9677
30
Cleaning and care
ƒꢀDo not clean any part of your CC2300 with benzene, thinners or other
solvent chemicals – this may cause permanent damage which is not covered by
the Guarantee. When necessary, clean it with a damp cloth.
ƒꢀKeep your CC2300 away from hot, humid conditions or strong sunlight,
and don’t let it get wet.
ƒꢀEvery effort has been made to ensure high standards of reliability for your
CC2300. However, if something does go wrong, please do not try to repair
it yourself – consult your supplier or the Binatone Helpline.
Declaration of conformity
The cordless phone, identified as CC2300, complies with the essential protective
requirements and objectives of:
ƒꢀEC R&TTE Directive 1999/5/EC
ƒꢀEC Low Voltage Directive 2006/95/EC
ƒꢀEC EMC Directive 89/336/EEC
And conforms to the following relevant harmonized standards:
ƒꢀRadio: EN 301406 (TBR 6)
ƒꢀEMC: EN 301489
ƒꢀSafety: EN 60950
The conformity to the requirements is validated by the
symbol.
NOTE: In compliance with Directive 2002/96/EC, when you purchase
a product that comes with the symbol shown on the right, you are
required to dispose the electrical and electronic equipment by separate
waste collection and you cannot dispose of the product as normal
waste. This equipment and all its components, subsystems and
consumable materials form an integral part of this product and when
you decide to dispose them, you have to bring them to the local
recycling centres for appropriate waste disposal, in compliance with
the current regulations. Details about the location of these centres can
be obtained from your local authority.
Binatone Help Line : 0845 345 9677
31
Guarantee and service
The CC2300 is guaranteed for 12 months from the date of purchase shown on your
sales receipt. This guarantee does not cover any faults or defects caused by accidents,
misuse, fair wear and tear, neglect, faults on the telephone line, lightning, tampering with
the equipment, or any attempt at adjustment or repair other than through approved agents.
Please keep your sales (till) receipt – this is your guarantee. You should also keep
the original packaging material.
In the unlikely event that you need to return your CC2300 to our Repair Centre
while it is under guarantee, there will be a £5 handling charge.
While the unit is under Guarantee
1. Disconnect the base unit from the telephone line and the mains electricity supply
2. Pack up all parts of your CC2300, using the original packaging. Remember to
include the mains adapter
3. Return the unit to the shop where you bought it, making sure you take your sales
receipt.
After the Guarantee has expired
If the unit is no longer under Guarantee, first follow steps 1 and 2 as for repair under
Guarantee.
Then…
3. Call Binatone Helpline on 0845 345 9677 (for UK only) and ask for a quotation of
the repair charge and details of where to send your CC2300 for repair.
4. Make sure you include with your CC2300:
ƒꢀYour name and address
ƒꢀA cheque or postal order for the value of the repair charge
5. Return your CC2300 to the address given by the Service Department.
* This does not affect your statutory rights.
Binatone Help Line : 0845 345 9677
32
Technical details
Standard
Cordless Telecommunication
1.88 to 1.9 GHz (bandwidth = 20 MHz)
1.728 MHz
Frequency range
Channel bandwidth
Operating range
Operating time
Up to 300m outdoors; up to 50m indoors
Standby: 150 hours
Talking: 9 hours
Battery charge time: 24 hours
Temperature range
Electrical power
Operating 0 ºC to 40 ºC
Storage -20 ºC to 60 ºC
HANDSET – two pcs of AAA-size 550mAH NiMH 1.2V rechargeable batteries
Base UNIT – input 230VAC 50Hz; output 7.5VDC – 500mA
CHARGER POD – input 230VAC 50Hz; output 6VDC – 200mA
Port specification The
port with respect to EN41003.
port (connect to the mains power supply) is a SELV
The
port (connected to the telephone line) is a TNV port with respect to
EN41003.
PBX compatibility:
Timed break recall (flash): adjustable to 100ms (default), 250ms or 600ms
Pause length: 3 seconds
Dialling type: Tone (DTMF, dual tone multi-frequency) or Pulse (loop disconnect).
Network connection: This equipment is intended to be used in the UK only.
Operation on other countries' PSTN termination points cannot be guaranteed.
Binatone Telecom plc operates a policy of continuous improvement, and so
reserves the right to make changes to the products and functions without notice.
Binatone Help Line : 0845 345 9677
33
|