Audiovox LCM4000 User Manual

LCM-4000  
4" Active Matrix LCD Monitor  
Owner’s Manual  
SPECIFICATIONS  
1. Type:  
Color Liquid Crystal Display (LCD)  
Monitor  
2. Display Screen Size: 4 inches  
(82.1 x 61.8mm) ( W x H )  
Element : TFT LCD  
Format : 480 (W) x 234 (H) dot  
Total 112,320 dot  
3. Back Light:  
Cold Cathode Fluorescent Lamp  
+12 VDC  
4. Power Source:  
5. Power Consumption: 11W  
6. Connection Terminals: Video/Audio Input Jacks (RCA)  
External Power Jack (DC IN 12V)  
IR Jack  
7. Operating Temperature: 32°F - 104°F  
(0°C - 40°C)  
8. Storage Temperature: -4°F - 176°F  
(-20°C - +80°C)  
9. Cabinet Dimensions: 5.4 in x 3.9 in X 1.14 in (WxHxD)  
(136 x 98.3 x 29 mm)  
10. Weight:  
1 lb (400g)  
NTSC  
11. Video Format:  
3
CONTROLS AND INDICATORS  
FRONT PANEL  
1
2
3
4
5
6
1. Power On LED Indicator  
2. Power On/Off Switch  
3. Remote Control Sensor  
4. Picture Select  
5. On Screen Adjustment Up Button  
6. On Screen Adjustment Down Button  
4
REAR PANEL  
To Optional  
IR Transmitter  
Part Number IRT456  
11  
NOTE(B)  
12  
8
7
10  
NOTE(A)  
9
7. Power Input Connector:  
Red = +12 VDC  
Black = ground  
8. Video Signal Input Connector  
9. IR Repeater Connector  
10. IR Repeater Transmitter  
11. Audio Right Channel Input Connector  
12. Audio Left Channel Input Connector  
5
Note A : This cable (10) is utilized to connect to Video Cas-  
sette Players that do not accept the IR Repeater 1/8"  
(3.5mm) style plug (9). The IR Repeater Transmitter is  
provided with an adhesive that allows it to adhere to  
Video Cassette Player remote sensor. Remove the  
backing covering the adhesive and place the IR Re-  
peater Transmitter directly over the Video Cassette  
Player remote sensor.  
Note B :  
Connector (11) and (12) are Audio input Jacks reserved  
for optional IR Wireless Transmitter use (IRT456).  
IR Wireless Transmitter is a device for transmitting  
(audio sound without using wires) to IR Headphones.  
Please contact Audiovox dealers for this optional ac-  
cessory.  
OPERATION  
1. Connect the monitor power input plug (7) to a DC power  
source (Red plug +12 VDC, Black plug (-) to ground).  
2. Connect the external video source output signal (from VCP/  
DVD, TV Etc.) to the VIDEO IN jack (8).  
3. Press power On/Off button (2) to turn the monitor on and off.  
The LED power indicator will light red.  
4. Press the Picture Select button (4) to adjust the picture  
display characteristics. The adjustments will be shown on  
the On Screen Display in the following sequence: Contrast,  
Brightness, Color, and TINT.  
5. While in the picture select mode (video adjustment), press  
the up button (5) to increase the selected adjustment level  
or press the down button (6) to decrease the level.  
6
GENERAL INSTALLATION INFORMATION  
1. Installation will vary from vehicle to vehicle, as headrests in  
vehicles are not standard.  
2. This unit is intended for installation by professional installers.  
3. The kit consists of the screen assembly, a mounting hous-  
ing, key to remove screen from housing, wiring harness,  
remote control unit and remote control unit batteries.  
4. To release screen from housing, slide the key on either the  
right or left side of the screen between the housing and  
screen assembly to release the two clips which hold the  
screen assembly in the housing.  
5. To install the screen assembly into the housing simply  
insert the screen assembly until you hear the clips click into  
the locking position.  
6. Headrests will have to be cut to install the screen assembly  
housing.  
Caution - Do not over-cut the headrest beyond the height and  
width of the housing.  
7. To fasten the housing to the headrest, use either screws or  
tie wraps. Find a suitable mounting surface in the headrest  
to secure the housing.  
Caution - Use the proper length screws, which will vary with  
each headrest. If a suitable mounting surface cannot be  
found, use tie wraps to secure the housing.  
8. Attach the wiring to the screen, through the housing into and  
down the headrest and seat before permanently mounting  
the housing and screen assembly.  
9. Follow the wiring diagram in the owner’s manual for proper  
wiring connections.  
7
NOTE: A Remote Control Unit is included which will perform  
the Functions and adjustments of Operation items 3,  
4, and 5 as well as additional features as noted below.  
REMOTE CONTROL FUNCTIONS:  
LCD/VCP: ........Power button for LCD/VCP  
REPLAY: ..........Press to rewind tape and automatically go to  
play mode.  
PICTURE SEL: .On ScreenDisplay(OSD)forcolor, tint,brightness,  
contrast. Use ± to adjust  
REW: ............... Rewinds tape  
FWD: ............... Fast Forward tape  
PLAY: ...............Plays tape  
STOP: ..............Stops tape  
CAUTION  
1. Do not operate the monitor at temperatures below 32°F  
(0°C) or above 104°F (40°C).  
2. Keep the monitor clean and dry.  
3. Always seek qualified personnel to perform repairs. Never  
attempt your own repairs.  
4. Do not drop the monitor or expose to strong impacts.  
5. Do not expose to direct sunlight for extended periods of  
time.  
© 2000 Audiovox Electronics Corp., Hauppauge, NY  
128-5969  
8

Gateway HX2000 User Manual
Electrolux WLXRABOOOC User Manual
Electrolux WLWWAAOOOC User Manual
Dell UltraSharp 2209WA User Manual
Cypress MoBL CY62148BN User Manual
Cleveland Range Inc Convection Oven CR28 FP User Manual
BenQ Computer Monitor G2400WA User Manual
Asus Computer Monitor MB19 User Manual
AOC Computer Monitor V27M User Manual
AOC 2230 User Manual