®
CUBX-L/CUBX-E
Socket 370 ATX Motherboard
USER’S MANUAL
Special Features
CUBX-L
• UltraDMA/33 Support
• 2 USB Ports
CUBX-E
• UltraDMA/100 Support
• 5 USB Ports (2 standard, 3 upgradeable)
ASUS CONTACT INFORMATION
ASUSTeK COMPUTER INC. (Asia-Pacific)
Marketing
Address:
Telephone:
Fax:
150 Li-Te Road, Peitou, Taipei, Taiwan 112
+886-2-2894-3447
+886-2-2894-3449
Email:
Technical Support
MB/Others (Tel): +886-2-2890-7121 (English)
Notebook (Tel):
+886-2-2890-7122 (English)
Desktop/Server (Tel):+886-2-2890-7123 (English)
Fax:
+886-2-2895-9254
www.asus.com.tw
Email:
WWW:
FTP:
ftp.asus.com.tw/pub/ASUS
ASUS COMPUTER INTERNATIONAL (America)
Marketing
Address:
6737 Mowry Avenue, Mowry Business Center, Building 2
Newark, CA 94560, USA
Fax:
Email:
+1-510-608-4555
Technical Support
Fax:
+1-510-608-4555
www.asus.com
ftp.asus.com/Pub/ASUS
Email:
WWW:
FTP:
ASUS COMPUTER GmbH (Europe)
Marketing
Address:
Fax:
Harkortstr. 25, 40880 Ratingen, BRD, Germany
+49-2102-442066
Email:
[email protected] (for marketing requests only)
Technical Support
Hotline:
Fax:
Support (Email):
WWW:
MB/Others: +49-2102-9599-0 Notebook: +49-2102-9599-10
+49-2102-9599-11
www.asuscom.de/de/support (for online support)
www.asuscom.de
FTP:
ftp.asuscom.de/pub/ASUSCOM
ASUS CUBX-L/CUBX-E User’s Manual
3
CONTENTS
1. INTRODUCTION .............................................................................. 7
1.1 How This Manual Is Organized .................................................. 7
1.2 Item Checklist ............................................................................. 7
2. FEATURES ......................................................................................... 8
2.1 The ASUS CUBX-L/CUBX-E Motherboard ............................. 8
2.1.1 Specifications .................................................................. 8
2.1.2 Special Features ............................................................. 10
2.1.3 Performance Features .................................................... 10
2.1.4 Intelligence .................................................................... 11
2.2 Motherboard Components ........................................................ 12
2.2.1 Component Locations .................................................... 13
3. HARDWARE SETUP ...................................................................... 14
3.1 CUBX-L/CUBX-E Motherboard Layout ................................. 14
3.2 Layout Contents ........................................................................ 15
3.3 Hardware Setup Procedure ....................................................... 17
3.4 Motherboard Settings ................................................................ 17
3.5 System Memory (DIMM) ......................................................... 22
3.5.1 General DIMM Notes .................................................... 22
3.5.2 Memory Installation ...................................................... 23
3.6 Central Processing Unit (CPU) ................................................. 25
3.7 Expansion Cards ....................................................................... 26
3.7.1 Expansion Card Installation Procedure ......................... 26
3.7.2 Assigning IRQs for Expansion Cards............................ 27
3.7.3 Accelerated Graphics Port (AGP) ................................. 29
3.8 Connectors ................................................................................ 30
3.9 Starting Up the First Time ........................................................ 41
4. BIOS SETUP..................................................................................... 42
4.1 Managing and Updating Your BIOS ......................................... 42
4.1.1 Upon First Use of the Computer System....................... 42
4.1.2 Updating BIOS Procedures (only when necessary) ...... 43
4.2 BIOS Setup Program ................................................................ 45
4.2.1 BIOS Menu Bar ............................................................. 46
4.2.2 Legend Bar .................................................................... 46
4.3 Main Menu ................................................................................ 48
4.3.1 Primary & Secondary Master/Slave .............................. 49
4.3.2 Keyboard Features ......................................................... 52
4
ASUS CUBX-L/CUBX-E User’s Manual
CONTENTS
4.4 Advanced Menu ........................................................................ 54
4.4.1 Chip Configuration ........................................................ 58
4.4.2 I/O Device Configuration .............................................. 60
4.4.3 PCI Configuration ......................................................... 62
4.4.4 Shadow Configuration ................................................... 65
4.5 Power Menu .............................................................................. 66
4.5.1 Power Up Control .......................................................... 68
4.5.2 Hardware Monitor ......................................................... 70
4.6 Boot Menu ................................................................................ 71
4.7 Exit Menu ................................................................................. 73
5. SOFTWARE SETUP ....................................................................... 75
5.1 Install Operating System ........................................................... 75
5.2 Start Windows ........................................................................... 75
5.3 Installing Drivers and Software ................................................ 75
6. SOFTWARE REFERENCE ........................................................... 79
6.1 ASUS PC Probe ........................................................................ 79
6.2 ASUS Update ............................................................................ 84
7. APPENDIX........................................................................................ 85
7.1 PCI-L101 Fast Ethernet Card ................................................... 85
7.2 ASUS CIDB Intrusion Detection Module ................................ 87
7.3 Glossary .................................................................................... 89
INDEX ................................................................................................... 93
ASUS CUBX-L/CUBX-E User’s Manual
5
FCC & DOC COMPLIANCE
Federal Communications Commission Statement
This device complies with FCC Rules Part 15. Operation is subject to the following
two conditions:
•
•
This device may not cause harmful interference, and
This device must accept any interference received, including interference that
may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installa-
tion. This equipment generates, uses and can radiate radio frequency energy and, if
not installed and used in accordance with manufacturer's instructions, may cause
harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interfer-
ence by one or more of the following measures:
•
•
•
Re-orient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment to an outlet on a circuit different from that to which the
receiver is connected.
•
Consult the dealer or an experienced radio/TV technician for help.
WARNING! Any changes or modifications to this product not expressly ap-
proved by the manufacturer could void any assurances of safety or performance
and could result in violation of Part 15 of the FCC Rules.
Reprinted from the Code of Federal Regulations #47, part 15.193, 1993. Washington DC: Office of the
Federal Register, National Archives and Records Administration, U.S. Government Printing Office.
Canadian Department of Communications Statement
This digital apparatus does not exceed the Class B limits for radio noise emissions
from digital apparatus set out in the Radio Interference Regulations of the Canadian
Department of Communications.
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
6
ASUS CUBX-L/CUBX-E User’s Manual
1. INTRODUCTION
1.1 How This Manual Is Organized
This manual is divided into the following sections:
1. INTRODUCTION
2. FEATURES
3. HARDWARE SETUP
4. BIOS SETUP
Manual information and checklist
Production information and specifications
Intructions on setting up the motherboard.
Intructions on setting up the BIOS
5. SOFTWARE SETUP
6. SOFTWARE REFERENCE
7. APPENDIX
Intructions on setting up the included software
Reference material for the included software
Optional items and general reference
1.2 Item Checklist
Please check that your package is complete. If you discover damaged or missing
items, please contact your retailer.
Package Contents
Optional Items
(1) ASUS Motherboard
ASUS CIDB chassis intrusion de-
tection module
(1) Ribbon cable for internal
UltraDMA/33 IDE drives
ASUS IrDA-compliant infrared
module
(1) Ribbon cable for one 5.25” and
ASUS PCI-L101 Wake-On-LAN
10/100 Ethernet Card
two 3.5” floppy disk drives
(1) Bag of spare jumper caps
(1) ASUS Support CD with
drivers and utilities
(1) This Motherboard User’s
Manual
(1) 40-pin 80-conductor ibbon cable
for internal UltraDMA100/66/33
IDE drives (only for CUBX-E)
(1) Promise ATA100 Support Disk
(only for CUBX-E)
ASUS CUBX-L/CUBX-E User’s Manual
7
2. FEATURES
2.1 The ASUS CUBX-L/CUBX-E
Motherboard
TheASUS CUBX-L/CUBX-E is carefully designed for the demanding PC user who
wants advanced features processed by the fastest CPU.
2.1.1 Specifications
•
Latest Intel Processor Support
Intel Pentium® III
Intel Celeron™
Intel Celeron™
100MHz FSB Coppermine core
66MHz FSB Coppermine core
66MHz FSB Mendocino
FC-PGA
FC-PGA
PPGA
•
Intel AGPset: Features Intel’s 440BX AGPset with I/O subsystems and front-side
bus(FSB)platform, whichbooststhetraditional66MHzexternalbusspeedto100MHz.
•
JumperFree™ Mode: Allows processor settings and easy overclocking of fre-
quency and Vcore voltage all through BIOS setup when JumperFree™ mode is
enabled. Easy-to-use DIP switches instead of jumpers are included to allow
manual adjustment of the processor’s external frequency.
•
•
Anti-Boot Virus BIOS: Features a programmable BIOS, offering enhanced
Advanced Configuration Power Interface (ACPI) support for Windows 98 com-
patibility, built-in firmware-based virus protection through Trend ChipAway Virus
codes, and autodetection of most devices for virtually automatic setup.
PC100 Memory Support: Equipped with four DIMM sockets to support Intel
PC100-compliant SDRAMs (8, 16, 32, 64, 128, or 256MB) up to 1 GB. These
new SDRAMs are necessary to meet the critical enhanced 100MHz bus speed
requirement.
•
•
Peripheral Wake Up: Supports modem, PS/2 keyboard, PS/2 mouse, and LAN
card wake up functions from sleep or soft-off mode.
PC Health Monitoring: Provides an easier way to examine and manage system
status information, such as CPU and system voltages, temperatures, and fan
status through the onboard hardware ASIC and the bundled LDCM by Intel or
PC Probe from ASUS.
•
•
AGP Slot: Supports an Accelerated Graphics Port card for high performance,
component level interconnect targeted at 3D graphical display applications us-
ing a 1X or 2X mode bus.
PCI/ISA Expansion Slots: Provides five 32-bit PCI (rev 2.2) and two ISA ex-
pansion slots. PCI supports up to 133MB/s maximum throughput.
ASUS CUBX-L/CUBX-E User’s Manual
8
2. FEATURES
•
•
Multi-I/O: Provides two high-speed UART compatible serial ports and one paral-
lel port with EPP and ECP capabilities.
UltraDMA/33 Bus Master IDE: Comes with an onboard PCI Bus Master IDE
controller with two connectors that support four UltraDMA/33 IDE devices on
two channels. Supports UltraDMA/33, PIO Modes 3 and 4, and Bus Master IDE
DMA Mode 2, as well as Enhanced IDE devices, such as Tape Backup, CD-
ROM, CD-R/RW, and LS-120 drives.
•
Wake-On-LAN Connector: Supports Wake-On-LAN activity through an op-
tional ASUS PCI-L101 10/100 Fast Ethernet PCI card (see 7.1 PCI-L101 LAN
Card) or a similar ethernet card.
•
Suspend and Go: Suspend-to-RAM (STR) provides maximum power savings
as an alternative to leaving the computer ON and QuickStart™ so that you do
not have to wait for a long time for system bootup (see Suspend-to-RAM Ca-
pability in 4.5 Power Menu for more information).
•
•
Promise PCI-ATA100 Support (only on CUBX-E): Provides support to PCI-
ATA100 controller to provide Ultra DMA/100 solutions.
Supports Up to 5 USB Ports (only on CUBX-E): Provides support for up to
five USB ports right out of the box.
ASUS CUBX-L/CUBX-E User’s Manual
9
2. FEATURES
2.1.2 Special Features
•
ACPI Ready: Advanced Configuration Power Interface (ACPI) provides more
Energy Saving Features for operating systems that support OS Direct Power
Management (OSPM) functionality. With these features implemented in the OS,
PCs can be ready around the clock, yet satisfy all the energy saving standards.
To fully utilize the benefits of ACPI, an ACPI-supported OS such as Windows
98 must be used.
•
•
Easy Installation: Incorporates BIOS that supports autodetection of hard disk
drives, PS/2 mouse, and Plug and Play devices to make the setup of hard disk
drives, expansion cards, and other devices virtually automatic.
New Compliancy: Both the BIOS and hardware levels of this motherboard meet
the stringent requirements for PC’99 certification. The new PC’99 requirements
for systems and components are based on the following high-level goals: Sup-
port for Plug and Play compatibility and power management for configuring
and managing all system components, and 32-bit device drivers and installation
procedures for Windows95/98/NT . Color-coded connectors and descriptive icons
make identification easy as required by PC’99.
•
Symbios SCSI BIOS: Supports optional ASUS SCSI controller cards through
the onboard SYMBIOS firmware.
2.1.3 Performance Features
•
Concurrent PCI: Concurrent PCI allows multiple PCI transfers from PCI mas-
ter busses to the memory and processor.
•
SDRAM Optimized Performance: Supports the new generation memory - Syn-
chronous Dynamic RandomAccess Memory (SDRAM) which increases the data
transfer rate to 800MB/s max using PC100-compliant SDRAM.
•
High-Speed Data Transfer Interface: The CUBX-L motherboard supports
UltraDMA/33 and can handle data transfer rates up to 33MB/s. The CUBX-E
motherboard supports UltraDMA/100, which increases the data transfer rate to
100MB/s. UltraDMA/100 is backward compatible with DMA/66, DMA/33, and
DMA and with existing DMA devices and systems so there is no need to up-
grade current EIDE/IDE drives and host systems. (UltraDMA/66 and UltraDMA/
100 require a 40-pin 80-conductor cable to be enabled.)
ASUS CUBX-L/CUBX-E User’s Manual
10
2. FEATURES
2.1.4 Intelligence
•
Dual Function Power Button: Pushing the power button for less than 4 sec-
onds when the system is in the working state places the system into one of two
states: sleep mode or soft-off mode, depending on the BIOS or OS setting (see
PWR Button < 4 Secs in 4.5 Power Menu). When the power button is pressed
for more than 4 seconds, the system enters the soft-off mode regardless of the
BIOS setting.
•
•
Fan Status Monitoring and Alarm: To prevent system overheat and system
damage, the CPU, power supply, and system fans can be monitored for RPM
and failure. All fans are set for its normal RPM range and alarm thresholds.
Message LED (requires ACPI OS support): Turbo LEDs now act as informa-
tion providers. Through the way a particular LED illuminates, the user can de-
termine if a message has been received from a fax/modem. A simple glimpse
provides useful information to the user.
•
•
Remote Ring On (requires modem): This allows a computer with this mother-
board to be turned on remotely through an internal or external modem. With this
feature, users can access their computers from anywhere in the world!
System Resources Alert: Today’s operating systems such as Windows 95/98/
NT and OS/2, require much more memory and hard drive space to present enor-
mous user interfaces and run large applications. The system resource monitor
will warn the user before the system resources are used up to prevent possible
application crashes. Suggestions will give the user information on managing
their limited resources more efficiently.
•
Voltage Monitoring and Alert: System voltage levels are monitored to ensure
stable voltage to critical motherboard components. Voltage specifications are
more critical for future processors, so monitoring is necessary to ensure proper
system configuration and management.
ASUS CUBX-L/CUBX-E User’s Manual
11
2. FEATURES
2.2 Motherboard Components
See opposite page for locations.
Location
Processor Support Socket 370 for Pentium III/Celeron Processors ....................... 1
Feature Setting DIP Switches ................................................... 8
100/66MHz system bus (Frequency Multiples 2.0-8.0)
Chipsets Intel 440BX AGPset ................................................................. 3
Multi-I/O Chipset ................................................................... 16
Main Memory Maximum 1GB Supported
4 DIMM Sockets ...................................................................... 4
PC100/66 SDRAM Supported
Expansion Slots 5 PCI Slots .............................................................................. 17
2 ISA Slots .............................................................................. 12
1 Accelerated Graphics Port ................................................... 18
System I/O 2 UltraDMA/33 IDE Connectors ............................................. 5
2 UltraDMA/100 IDE Connectors (only on CUBX-E)............ 5
1 Floppy Disk Drive Connector ............................................... 9
Intel PIIX4E PCIset ................................................................ 10
1 Parallel Port Connector ....................................................... 21
2 Serial Port Connectors ................................................... 20, 22
2 USB Headers (only on CUBX-E) ......................................... 6
2 USB Connectors .................................................................. 23
1 PS/2 Mouse Connector .............................................. (Top) 24
1 PS/2 Keyboard Connector ................................... (Bottom) 24
BIOS AWARD BIOS, Programmable Flash 4Mbit EEPROM ........ 14
Supports Plug & Play, DMI, and Write Protection
Network Features Wake-On-LAN Connector...................................................... 15
Wake-On-Ring Connector ...................................................... 13
Hardware Monitoring System Voltage Monitoring (integrated in ASUS ASIC) ......... 7
3 Fan Power and Speed Monitoring Connectors
Power ATX Power Supply Connector ................................................. 2
Special Features Onboard Power LED .............................................................. 11
Promise® UltraDMA/100 Controller (only on CUBX-E) ...... 19
Form Factor ATX
ASUS CUBX-L/CUBX-E User’s Manual
12
2. FEATURES
2.2.1 Component Locations
1
2
3
4
5
4
3
2
1
0
9
8
7
6
5
4
3
12
11 10 9 8 7
6
ASUS CUBX-L/CUBX-E User’s Manual
13
3. HARDWARE SETUP
3.1 CUBX-L/CUBX-E Motherboard Layout
21.8 cm (8.6 in)
PS/2KBMS
ATXPWR
T: Mouse
CPU_FAN
PWR_FAN
B: Keyboard
USB
T: Port1
B: Port
2
COM1
JTPWR
Socket 370
Intel
COM2
440BX
AGPset
Promise
ATA100
0
1
2
3
4
5
6
7
Row
CR2032 3V
Accelerated Graphics Port
Lithium Cell
DSW
DIP
Switches
CMOS Power
LED1
PCI1
PCI2
FLOPPY
Multi-I/O
SMB
WOL_CON
CHASIS
CHA_FAN
PCI3
PCI4
PCI5
Intel
PIIX4E CLRTC
PCIset
ASUS
ASIC
with
Hardware
Monitor
WOR
JEN
USB3A
USB2
PANEL
ISA1
ISA2
IDELED
IR
(Grayed components are only available on the CUBX-E motherboard.)
ASUS CUBX-L/CUBX-E User’s Manual
14
3. HARDWARE SETUP
3.2 Layout Contents
Motherboard Settings
1) JEN
p. 18 JumperFree Mode Setting (Disable/Enable)
p. 20 AGP Bus Frequency Setting
2) DSW 6
3) DSW 5–10
4) DSW 1-4
p. 20 CPU External Frequency Selection
p. 21 CPU Core:BUS Frequency Multiple Selection
Expansion Slots/Sockets
1) System Memory
p.22 System Memory Support
p.22 DIMM Memory Module Support
p.25 CPU Support
2) DIMM1/2/3/4
3) Socket 370
4) PCI1/2/3/4/5
5) ISA1/ISA2
6) AGP
p.27 32-bit PCI Bus Expansion Slots
p.27 16-bit ISA Bus Expansion Slots
p.29 Accelerated Graphics Port
Connectors
1) PS2KBMS
p.30 PS/2 Mouse Port Connector (6 pin-female)
p.30 PS/2 Keyboard Port Connector (6-pin female)
p.31 Universal Serial Bus Connectors 1 & 2 (Two 4-pin female)
p.31 Parallel Port Connector (25-pin female)
p.31 Serial Port Connector (Two 9-pin male)
p.32 Chassis Intrusion Lead (4-1 pins)
2) PS2KBMS
3) USB
4) PRINTER
5) COM1/COM2
6) CHASSIS
7) PRIMARY IDE
SECONDARY IDE
THIRD IDE
p.33 UltraDMA/66 IDE Connectors (Two 40-1 pins)
UltraDMA/100 IDE Connectors (only on CUBX-E)
FOURTH IDE
8) FLOPPY
9) WOL_CON
10) WOR
p. 33 Floppy Disk Drive Port Connector (34 pins)
p. 34 Wake-On-LAN Connector (3 pins)
p. 34 Wake-On-Ring Connector (2 pins)
p. 35 IDE Activity LED (2 pins)
11) IDELED
12) PWR_, CPU_,CHA_FAN p. 35 Chassis, Power Supply, CPU Fan Connectors (3 pins)
13) IR
p. 36 Infrared Module Connector (5 pins)
p. 37 SMBus Connector (5-1 pins)
14) SMB
15) USB2, USB3A
16) PWR.LED (PANEL
p. 37 USB Headers (10-1 pins, 5-1 pins)
p. 38 System Power LED Lead (3 pins)
p. 38 Keyboard Lock Switch Lead (2 pins)
p. 38 System Warning Speaker Connector (4 pins)
)
17) KEYLOCK (PANEL
)
18) SPEAKER (PANEL)
ASUS CUBX-L/CUBX-E User’s Manual
15
3. HARDWARE SETUP
19) MSG.LED (PANEL)
p. 38 System Message LED (2 pins)
20) SMI (PANEL)
21) PWR.SW (PANEL)
22) RESET (PANEL)
23) ATXPWR
p. 38 System Management Interrupt Lead (2 pins)
p. 38 ATX / Soft-Off Switch Lead (2 pins)
p. 38 Reset Switch Lead (2 pins)
p. 39 ATX Power Supply Connector (20 pins)
p. 39 Power Supply Thermal Sensor Connector (2 pins)
24) JTPWR
ASUS CUBX-L/CUBX-E User’s Manual
16
3. HARDWARE SETUP
3.3 Hardware Setup Procedure
Before using your computer, you must complete the following steps:
1. Check Motherboard Settings
2. Install Memory Modules
3. Install the Central Processing Unit (CPU)
4. Install Expansion Cards
5. Connect Ribbon Cables, Panel Wires, and Power Supply
6. Setup the BIOS Software
3.4 Motherboard Settings
This section explains in detail how to change your motherboard’s function settings
through the use of switches and/or jumpers.
WARNING! Computer motherboards and expansion cards contain very delicate
Integrated Circuit (IC) chips. To protect them against damage from static electric-
ity, you should follow some precautions whenever you work on your computer.
1. Unplug your computer when working on the inside.
2. Use a grounded wrist strap before handling computer components. If you
do not have one, touch both of your hands to a safely grounded object or to
a metal object, such as the power supply case.
3. Hold components by the edges and try not to touch the IC chips, leads or
connectors, or other components.
4. Place components on a grounded antistatic pad or on the bag that came with
the component whenever the components are separated from the system.
WARNING! Make sure that you unplug your power supply when adding or
removing system components. Failure to do so may cause severe damage to
your motherboard, peripherals, and/or components. The onboard LED when lit
acts as a reminder that the system is in suspend or soft-off mode and not powered
OFF.
ON
OFF
Standby
Power
Powered
Off
CUBX-L/CUBX-E Onboard LED
ASUS CUBX-L/CUBX-E User’s Manual
17
3. HARDWARE SETUP
Motherboard Features Settings (DIP Switches - DSW)
The motherboard’s onboard functions are adjusted through the DIP switches. The
white block represents the switch’s position. The example below shows all the
switches in the OFF position.
1. Frequency Multiple
2. Frequency Multiple
3. Frequency Multiple
4. Frequency Multiple
5. (Reserved)
6. AGP Frequency Selection
7. Frequency Selection
8. Frequency Selection
9. Frequency Selection
10. Frequency Selection
DSW
ON
ON
OFF
1 2 3 4 5 6 7 8 9 10
CUBX-L/CUBX-E DIP Switches
1) JumperFree™ Mode (JEN)
This jumper allows you to enable or disable the JumperFree™ mode. The
JumperFree™ mode allows processor settings to be made through the BIOS
setup (see 4.4 Advanced Menu).
Setting
Enable (JumperFree) [2-3] (default)
Disable (Jumper) [1-2]
JEN
DSW
ON
OFF
1 2 3 4 5 6 7 8 9 10
JEN
1 2
2 3
JumperFree
Jumper
CUBX-L/CUBX-E Jumper Mode Setting
NOTE: In JumperFree™ mode, all dip switches (DSW) must be set to OFF.
ASUS CUBX-L/CUBX-E User’s Manual
18
3. HARDWARE SETUP
2) AGP Bus Frequency Setting (DSW Switch 6)
Thisoptionsetsthefrequency ratio between theAGPbus frequency and the DRAM
(CPU bus) frequency. The default sets the AGP bus frequency to be 2/3 of the
DRAM frequency. When the CPU/DRAM frequency is set to 66MHz, set this
switch to [ON]. See the processor table on the next page.
Setting
DRAM Freq. x 2/3
DRAM Freq. x 1
DSW Switch 6
[OFF] (default)
[ON]
ON
ON
1 2 3 4 5 6 7 8 9 10
1 2 3 4 5 6 7 8 9 10
DRAM Freq. x1
DRAM Freq. x2/3
CUBX-L/CUBX-E AGP Bus Frequency Setting
ASUS CUBX-L/CUBX-E User’s Manual
19
3. HARDWARE SETUP
3) CPU External Frequency Selection (DSW Switches 7-10)
This option tells the clock generator what frequency to send to the CPU, DRAM, and
the PCI bus.This allows the selection of the CPU’s External frequency (or BUS Clock).
The BUS Clock multiplied by the Frequency Multiple equals the CPU’s Internal fre-
quency (the advertised CPU speed).
ON
ON
ON
1 2 3 4 5 6 7 8 9 10
1 2 3 4 5 6 7 8 9 10
1 2 3 4 5 6 7 8 9 10
CPU/DRAM→
83.0MHz
41.6MHz
66.0MHz
33.4MHz
75.0MHz
37.5MHz
PCI BUS
→
ON
ON
ON
1 2 3 4 5 6 7 8 9 10
1 2 3 4 5 6 7 8 9 10
1 2 3 4 5 6 7 8 9 10
CPU/DRAM→
100.0MHz
33.4MHz
103.0MHz
34.3MHz
105.0MHz
35.0MHz
PCI BUS
→
ON
ON
ON
1 2 3 4 5 6 7 8 9 10
1 2 3 4 5 6 7 8 9 10
1 2 3 4 5 6 7 8 9 10
CPU/DRAM→110.0MHz
112.0MHz
37.3MHz
115.0MHz
38.3MHz
PCI BUS → 36.7MHz
ON
ON
ON
1 2 3 4 5 6 7 8 9 10
1 2 3 4 5 6 7 8 9 10
1 2 3 4 5 6 7 8 9 10
CPU/DRAM→
120.0MHz
40.0MHz
124.0MHz
41.3MHz
124.0MHz
31.0MHz
PCI BUS
→
ON
ON
ON
CUBX-L/CUBX-E CPU
1 2 3 4 5 6 7 8 9 10
1 2 3 4 5 6 7 8 9 10
1 2 3 4 5 6 7 8 9 10
External Frequency
Selection
CPU/DRAM→
133.0MHz
44.3MHz
140.0MHz
35.0MHz
133.0MHz
→
33.3MHz
PCI BUS
ON
1 2 3 4 5 6 7 8 9 10
CPU/DRAM→150.0MHz
PCI BUS → 37.5MHz
NOTE: Overclocking your processor is not recommended. It may result in a slower
speed.
ASUS CUBX-L/CUBX-E User’s Manual
20
3. HARDWARE SETUP
4) CPU Core:BUS Frequency Multiple (DSW Switches 1-4)
This option sets the frequency multiple between the Internal frequency of the
CPU and the CPU’s External frequency. These must be set in conjunction with the
CPU Bus Frequency.
ON
ON
ON
DSW
1 2 3 4 5 6 7 8 9 10
1 2 3 4 5 6 7 8 9 10
1 2 3 4 5 6 7 8 9 10
2.0x(2/1)
3.0x(3/1)
2.5x(5/2)
ON
ON
ON
1 2 3 4 5 6 7 8 9 10
1 2 3 4 5 6 7 8 9 10
1 2 3 4 5 6 7 8 9 10
3.5x(7/2)
4.0x(4/1)
4.5x(9/2)
ON
ON
ON
1 2 3 4 5 6 7 8 9 10
1 2 3 4 5 6 7 8 9 10
1 2 3 4 5 6 7 8 9 10
6.0x(6/1)
5.0x(5/1)
5.5x(11/2)
ON
ON
ON
1 2 3 4 5 6 7 8 9 10
1 2 3 4 5 6 7 8 9 10
1 2 3 4 5 6 7 8 9 10
6.5x(13/2)
7.0x(7/1)
7.5x(15/2)
CUBX-L/CUBX-E CPU :
BUS Frequency Multiple
ON
ON
1 2 3 4 5 6 7 8 9 10
1 2 3 4 5 6 7 8 9 10
8.0x(8/1)
TEST
Manual CPU Settings
NOTE: JumperFree mode must be disabled .
Set the DIP switches by the Internal speed of your processor as follows:
(CPU BUS Freq.)
10
(Freq. Multiple)
(AGP)
6
Intel CPU Model
Pentium III
Pentium III
Pentium III
Pentium III
Pentium III
Pentium III
Pentium III
Pentium III
Freq. Mult. Bus F.
7
8
9
1
2
3
4
800MHz 8.0x 100MHz [OFF][OFF][OFF] [ON] [ON] [ON] [OFF][OFF] [OFF]
750MHz 7.5x 100MHz [OFF][OFF][OFF] [ON] [OFF][OFF] [ON] [OFF] [OFF]
700MHz 7.0x 100MHz [OFF][OFF][OFF] [ON] [ON] [OFF] [ON][OFF]] [OFF]
650MHz 6.5x 100MHz [OFF][OFF][OFF] [ON] [OFF] [ON] [ON] [OFF] [OFF]
600MHz 6.0x 100MHz [OFF][OFF][OFF] [ON] [ON] [ON] [ON] [OFF] [OFF]
550MHz 5.5x 100MHz [OFF][OFF][OFF] [ON] [OFF][OFF][OFF] [ON] [OFF]
500MHz 5.0x 100MHz [OFF][OFF][OFF] [ON] [ON] [OFF][OFF] [ON] [OFF]
450MHz 4.5x 100MHz [OFF][OFF][OFF] [ON] [OFF] [ON] [OFF] [ON] [OFF]
Celeron
Celeron
Celeron
Celeron
Celeron
Celeron
Celeron
Celeron
Celeron
533MHz 8.0x 66MHz [OFF][OFF] [ON] [ON] [ON] [ON] [OFF][OFF] [ON]
500MHz 7.5x 66MHz [OFF][OFF] [ON] [ON] [OFF][OFF] [ON] [OFF] [ON]
466MHz 7.0x 66MHz [OFF][OFF] [ON] [ON] [ON] [OFF] [ON] [OFF] [ON]
433MHz 6.5x 66MHz [OFF][OFF] [ON] [ON] [OFF] [ON] [ON] [OFF] [ON]
400MHz 6.0x 66MHz [OFF][OFF] [ON] [ON] [ON] [ON] [ON] [OFF] [ON]
366MHz 5.5x 66MHz [OFF][OFF] [ON] [ON] [OFF][OFF][OFF] [ON] [ON]
333MHz 5.0x 66MHz [OFF][OFF] [ON] [ON] [ON] [OFF][OFF] [ON] [ON]
300MHz 4.5x 66MHz [OFF][OFF] [ON] [ON] [OFF] [ON] [OFF] [ON] [ON]
266MHz 4.0x 66MHz [OFF][OFF] [ON] [ON] [ON] [ON] [OFF] [ON] [ON]
For updated processor settings, please visit ASUS’ web site (see ASUS CONTACT INFORMATION).
WARNING! Frequencies other than the recommended CPU bus frequencies
are not guaranteed to be stable.
ASUS CUBX-L/CUBX-E User’s Manual
21
3. HARDWARE SETUP
3.5 System Memory (DIMM)
NOTE: No hardware or BIOS setup is required after adding or removing memory.
This motherboard uses only Dual Inline Memory Modules (DIMMs). Sockets are
available for 3.3Volt (power level) unbuffered Synchronous Dynamic Random Ac-
cess Memory (SDRAM). One side (with memory chips) of the DIMM takes up one
row on the motherboard.
To utilize the chipset’s Error Checking and Correction (ECC) feature, you must use a
DIMM module with 9 chips per side (standard 8 chips/side + 1 ECC chip).
Memory speed setup is recommended through SDRAM Configuration in 4.4.1
Chip Configuration.
Install memory in any combination as follows:
DIMM Location
168-pin DIMM
Total Memory
Socket 1 (Rows 0&1)
Socket 2 (Rows 2&3)
Socket 3 (Rows 4&5)
Socket 4 (Rows 6&7)
SDRAM 8, 16, 32, 64, 128, 256MB
SDRAM 8, 16, 32, 64, 128, 256MB
SDRAM 8, 16, 32, 64, 128, 256MB
SDRAM 8, 16, 32, 64, 128, 256MB
x1
x1
x1
x1
Total System Memory (Max 1024MB) =
3.5.1 General DIMM Notes
•
For the system CPU bus to operate at 100MHz, use only PC100-compliant
DIMMs. When this motherboard operates at 100MHz, most system will not
even boot if non-compliant modules are used because of the strict timing issues
involved under this speed. If your DIMMs are not PC100-compliant, set the
CPU bus frequency to 66MHz RAM to ensure system stability.
ASUS motherboards support SPD (Serial Presence Detect) DIMMs. This is the
memory of choice for best performance vs. stability.
•
•
•
Two possible memory chips are supported: SDRAM with and without ECC.
SDRAM chips are generally thinner with higher pin density than EDO (Ex-
tended Data Output) chips.
•
•
BIOS shows SDRAM memory on bootup screen.
Single-sided DIMMs come in 16, 32, 64,128MB; double-sided come in 32, 64,
128, 256MB.
ASUS CUBX-L/CUBX-E User’s Manual
22
3. HARDWARE SETUP
3.5.2 Memory Installation
WARNING! Make sure that you unplug your power supply when adding or
removing memory modules or other system components. Failure to do so may
cause severe damage to both your motherboard and expansion cards (see 3.3
Hardware Setup Procedure for more information).
Insert the module(s) as shown. Because the number of pins are different on either
side of the breaks, the module will only fit in the orientation shown. DRAM SIMM
modules have the same pin contacts on both sides. SDRAM DIMMs have different
pin contacts on each side and therefore have a higher pin density.
Lock
88 Pins
60 Pins
20 Pins
CUBX-L/CUBX-E 168-Pin DIMM Memory Sockets
The DIMMs must be 3.3Volt unbuffered SDRAMs. To determine the DIMM type,
check the notches on the DIMMs (see figure below).
The notches on the DIMM will shift between left, center, or right to identify the type
and also to prevent the wrong type from being inserted into the DIMM slot on the
motherboard. You must tell your retailer the correct DIMM type before purchasing.
This motherboard supports four clock signals per DIMM.
ASUS CUBX-L/CUBX-E User’s Manual
23
3. HARDWARE SETUP
(This page was intentionally left blank.)
ASUS CUBX-L/CUBX-E User’s Manual
24
3. HARDWARE SETUP
3.6 Central Processing Unit (CPU)
The motherboard provides a ZIF Socket 370. The CPU that came with the mother-
board should have a fan attached to it to prevent overheating. If this is not the case,
then purchase a fan before you turn on your system.
WARNING! Be sure that there is sufficient air circulation across the processor’s
heatsink by regularly checking that your CPU fan is working. Without sufficient
circulation, the processor could overheat and damage both the processor and the
motherboard. You may install an auxiliary fan, if necessary.
To install a CPU, first turn off your system and remove its cover. Locate the ZIF
socket and open it by first pulling the lever sideways away from the socket then
upwards to a 90-degree angle. Insert the CPU with the correct orientation as shown.
The notched corner should point towards the end of the lever. Because the CPU has
a corner pin for two of the four corners, the CPU will only fit in the orientation as
shown. The picture is for reference only; you should have a CPU fan that covers the
face of the CPU. With the added weight of the CPU fan, no force is required to
insert the CPU. Once completely inserted, close the socket’s lever while holding
down the CPU.After the CPU is , install an Intel recommended fan heatsink. Locate
the CPU fan connector (see 3.1 Motherboard Layout or 3.8 Connectors) and con-
nect the CPU fan cable to it.
NOTE: Do not forget to set the correct Bus Frequency and Multiple (frequency
multiple setting is available only on unlocked processors) for your Socket 370 pro-
cessor or else boot-up may not be possible. Socket 370 processors provide internal
thermal sensing so that a socket mounted thermal resistor is not needed.
CAUTION! Be careful not to scrape the motherboard when mounting a clamp-
style processor fan or else damage may occur to the motherboard.
Socket 370 CPU (Top) Socket 370 CPU (Bottom)
Celeron
Notch
Pentium III
CUBX-L/CUBX-E
Socket 370
Golden Arrow
ASUS CUBX-L/CUBX-E User’s Manual
25
3. HARDWARE SETUP
3.7 Expansion Cards
WARNING! Unplug your power supply when adding or removing expansion
cards or other system components. Failure to do so may cause severe damage to
both your motherboard and expansion cards.
3.7.1 Expansion Card Installation Procedure
1. Read the documentation for your expansion card and make any necessary hard-
ware or software settings for your expansion card, such as jumpers.
2. Remove your computer system’s cover and the bracket plate on the slot you
intend to use. Keep the bracket for possible future use.
3. Carefully align the card’s connectors and press firmly.
4. Secure the card on the slot with the screw you removed above.
5. Replace the computer system’s cover.
6. Set up the BIOS if necessary
(such as IRQ xx Used By ISA: Yes in 4.4.3 PCI Configuration)
7. Install the necessary software drivers for your expansion card.
26
ASUS CUBX-L/CUBX-E User’s Manual
3. HARDWARE SETUP
3.7.2 Assigning IRQs for Expansion Cards
Some expansion cards need an IRQ to operate. Generally, an IRQ must be exclu-
sively assigned to one use. In a standard design, there are 16 IRQs available but
most of them are already in use, leaving 6 IRQs free for expansion cards. If your
motherboard has PCI audio onboard, an additional IRQ will be used. If your moth-
erboard also has MIDI enabled, another IRQ will be used, leaving 4 IRQs free.
IMPORTANT: If using PCI cards on shared slots, make sure that the drivers sup-
port “Share IRQ” or that the cards do not need IRQ assignments. Conflicts will arise
between the two PCI groups that will make the system unstable or cards inoperable.
The following table lists the default IRQ assignments for standard PC devices. Use
this table when configuring your system and for resolving IRQ conflicts.
Standard Interrupt Assignments
IRQ
0
1
Priority
Standard Function
System Timer
Keyboard Controller
1
2
2
N/A
11
12
13
14
15
3
4
5
6
7
Programmable Interrupt
Communications Port (COM2)
Communications Port (COM1)
Sound Card (sometimes LPT2)
Floppy Disk Controller
Printer Port (LPT1)
System CMOS/Real Time Clock
ACPI Mode when used
IRQ Holder for PCI Steering
IRQ Holder for PCI Steering
PS/2 Compatible Mouse Port
Numeric Data Processor
Primary IDE Channel
3*
4*
5*
6
7*
8
9*
10*
11*
12*
13
14*
15*
8
9
10
Secondary IDE Channel
*These IRQs are usually available for ISA or PCI devices.
Interrupt Request Table for this Motherboard
INT-A
shared
—
INT-B
—
shared
—
INT-C
—
—
shared
—
—
—
—
—
—
INT-D
—
—
PCI slot 1
PCI slot 2
PCI slot 3
—
—
PCI slot 4
—
—
shared
shared
—
—
shared
—
PCI slot 5
—
—
AGP slot
shared
—
—
—
shared
—
ATA100 controller
Onboard USB controller
SMBus
—
—
ASUS CUBX-L/CUBX-E User’s Manual
27
3. HARDWARE SETUP
Both ISA and PCI expansion cards may require IRQs. System IRQs are available to
cards installed in the ISA expansion bus first, then any remaining IRQs are available
to PCI cards. Currently, there are two types of ISA cards.
The original ISA expansion card design, now referred to as legacy ISA cards, re-
quires that you configure the card’s jumpers manually and then install it in any
available slot on the ISA bus. To see a map of your used and free IRQs in Windows
98, the Control Panel icon in My Computer, contains a System icon, which gives
you a Device Manager tab. Double-clicking on a specific hardware device gives
you the Resources tab which shows the Interrupt number and address. Double-click
Computer to see all the interrupts and addresses for your system. Make sure that no
two devices use the same IRQ or your computer will experience problems when
those two devices are in use at the same time.
To simplify this process, this motherboard complies with the Plug and Play (PNP)
specification which was developed to allow automatic system configuration when-
ever a PNP-compliant card is added to the system. For PNP cards, IRQs are as-
signed automatically from those available.
If the system has both legacy and PNP ISA cards installed, IRQs are
assigned to PNP cards from those not used by legacy cards. The PCI and PNP con-
figuration of the BIOS setup utility can be used to indicate which IRQs are being
used by legacy cards. For older legacy cards that do not work with the BIOS, you
can contact your vendor for an ISA Configuration Utility.
An IRQ number is automatically assigned to PCI expansion cards after those used
by legacy and PNP ISA cards. In the PCI bus design, the BIOS automatically as-
signs an IRQ to PCI cards that require an IRQ. To install a PCI card, you need to set
the INT (interrupt) assignment. Since all the PCI slots on this motherboard use an
INTA #, be sure that the jumpers on your PCI cards are set to INT A.
Assigning DMA Channels for ISA Cards
Some ISAcards, both legacy and PNP, may also need to use a DMA(Direct Memory
Access) channel. DMA assignments for this motherboard are handled the same way
as the IRQ assignment process described earlier. You can select a DMA channel in
the PCI and PNP configuration section of the BIOS Setup utility.
IMPORTANT: To avoid conflicts, reserve the necessary IRQs and DMAs for
legacy ISA cards (see 4.4.3 PCI Configuration. Choose Yes in IRQ xx Used By
ISA and DMA x Used By ISA for those IRQs and DMAs you want to reserve).
28
ASUS CUBX-L/CUBX-E User’s Manual
3. HARDWARE SETUP
3.7.3 Accelerated Graphics Port (AGP)
This motherboard provides an accelerated graphics port (AGP) slot to support a new
generation of AGP graphics cards with ultra-high memory bandwidth.
CUBX-L/CUBX-E Accelerated Graphics Port (AGP)
WARNING! Make sure that you unplug your power supply when adding or re-
moving an expansion card or other system components. Failure to do so may cause
severe damage to both your motherboard and expansion cards (see 3.3 Hardware
Setup Procedure for more information).
ASUS CUBX-L/CUBX-E User’s Manual
29
3. HARDWARE SETUP
3.8 Connectors
WARNING! Some pins are used for connectors or power sources. These are
clearly distinguished from jumpers in the Motherboard Layout. Placing jumper
caps over these connector pins will cause damage to your motherboard.
IMPORTANT: Ribbon cables should always be connected with the red stripe to
Pin 1 on the connectors. Pin 1 is usually on the side closest to the power connec-
tor on hard drives and CD-ROM drives, but may be on the opposite side on
floppy disk drives. Check the connectors before installation because there may
be exceptions. IDE ribbon cables must be less than 46 cm (18 in.), with the
second drive connector no more than 15 cm (6 in.) from the first connector.
1) PS/2 Mouse Connector (Green 6-pin PS2KBMS)
The system will direct IRQ12 to the PS/2 mouse if one is detected. If one is not
detected, expansion cards can use IRQ12. See PS/2 Mouse Function Control
in 4.4 Advanced Menu.
PS/2 Mouse (6-pin Female)
2) PS/2 Keyboard Connector (Purple 6-pin PS2KBMS)
This connection is for a standard keyboard using an PS/2 plug (mini DIN). This
connector will not allow standard AT size (large DIN) keyboard plugs. You
may use a DIN to mini DIN adapter on standard AT keyboards.
PS/2 Keyboard (6-pin Female)
30
ASUS CUBX-L/CUBX-E User’s Manual
3. HARDWARE SETUP
3) Universal Serial Bus Ports (Black two 4-pin USB)
Two USB ports are available for connecting USB devices.
USB 1
Universal Serial Bus (USB) 2
4) Parallel Port Connector (Burgundy 25-pin PRINTER)
You can enable the parallel port and choose the IRQ through Onboard Parallel
Port (see 4.4.2 I/O Device Configuration).
NOTE: Serial printers must be connected to the serial port.
Parallel Port (25-pin Female)
5) Serial Port Connectors (Teal/Turquoise 9-pin COM1/COM2)
One serial port is ready for a mouse or other serial devices. A second serial port
is available using a serial port bracket connected from the motherboard to an
expansion slot opening. See Onboard Serial Port 1 in 4.2.2 I/O Device Con-
figuration for settings.
COM1
COM2
Serial Ports (9-pin Male)
ASUS CUBX-L/CUBX-E User’s Manual
31
3. HARDWARE SETUP
6) Chassis Intrusion Lead (4-1 pin CHASSIS)
This requires an external detection mechanism such as a chassis intrusion moni-
tor/sensor or microswitch. The sensor is triggered when a high level signal is
sent to the Chassis Signal lead, which occurs when a panel switch or light detec-
tor is triggered. This function requires the optional ASUS CIDB chassis intru-
sion module to be installed (see 7. APPENDIX). If the chassis intrusion lead is
not used, a jumper cap must be placed over pins 3 & 4 to close the circuit.
1
CHASSIS
CUBX-L/CUBX-E Chassis Intrusion Alarm Lead
7) Floppy Disk Drive Connector (34-1 pin FLOPPY)
This connector supports the provided floppy drive ribbon cable. After connect-
ing the single end to the board, connect the two plugs on the other end to the
floppy drives. (Pin 5 is removed to prevent inserting in the wrong orienta-
tion when using ribbon cables with pin 5 plugged).
NOTE: Orient the red stripe to Pin 1.
Floppy Drive Connector
Pin 1
CUBX-L/CUBX-E Floppy Disk Drive Connector
32
ASUS CUBX-L/CUBX-E User’s Manual
3. HARDWARE SETUP
8) IDE Connectors
(40-1 pin PRIMARY / SECONDARY IDE)
These connectors support the provided IDE hard disk ribbon cable.
After connecting the single end to the board, connect the two plugs at the other
end to your hard disk(s). If you install two hard disks, you must configure the
second drive to Slave mode by setting its jumper accordingly. Please refer to
your hard disk documentation for the jumper settings. (Pin 20 is removed to
prevent inserting in the wrong orientation when using ribbon cables with
pin 20 plugged).
TIP: You may configure two hard disks to be both Masters with two ribbon
cables – one for the primary IDE connector and another for the secondary IDE
connector and select the boot disk through the BIOS.
NOTE: Orient the red stripe to PIN 1.
PIN 1
CUBX-L IDE Connectors
(40-1 pin THIRD / FOURTH IDE) (only on CUBX-E)
Connect the 40-pin 80-conductor cable’s blue connector to the motherboard’s
primary (recommended) or secondary IDE connector, and then connect the cor-
responding gray connector to your UltraDMA/100 / UltraDMA/66 slave device
(hard disk drive) and the black connector to your UltraDMA/100 / UltraDMA/
66 master device. It is recommended that non-UltraDMA/100 / Ultra/66 devices
be connected to the secondary IDE connector.
NOTE: Orient the red stripe to PIN 1.
PIN 1
PIN 1
CUBX-E IDE Connectors
NOTES: UltraDMA/100 is backward compatible with DMA/66, DMA/33, and
DMA and with existing DMA devices and systems so there is no need to upgrade
current EIDE/IDE drives and host systems.
If you have more than two UltraDMA/100 / UltraDMA/66 devices, you will
need to purchase another UltraDMA/100 / UltraDMA/66 cable.
The hole near the blue connector on the UltraDMA/100 / UltraDMA/66 cable is
intentional.
IMPORTANT: UltraDMA/66 and UltraDMA/100 IDE devices require a 40-pin
80-conductor cable to be enabled.
ASUS CUBX-L/CUBX-E User’s Manual
33
3. HARDWARE SETUP
9) Wake-On-LAN Connector (3-pin WOL_CON)
This connector connects to a LAN card with a Wake-On-LAN output, such as the
ASUS PCI-L101 Ethernet card (see 7. APPENDIX). The connector powers up
the system when a wakeup packet or signal is received through the LAN card.
IMPORTANT: This feature requires that Wake-On-LAN features are enabled
(see 4.5.1 Power Up Control) and that your system has an ATX power supply
with at least 720mA +5V standby power.
WOL_CON
+5VSB
Ground
PME
CUBX-L/CUBX-E Wake-On-LAN Connector
10) Wake-On-Ring Connector (2-pin WOR)
This connector connects to internal modem cards with a Wake-On-Ring output.
The connector powers up the system when a ringup packet or signal is received
through the internal modem card. NOTE: For external modems, Wake-On-Ring
is detected through the COM port.
IMPORTANT: This feature requires that Wake-On-Ring features are enabled
(see 4.5.1 Power Up Control) and that your system has an ATX power supply
with at least 720mA +5V standby power.
WOR
1
2
Ground
PIXRI#
CUBX-L/CUBX-E Wake-On-Ring Connector
34
ASUS CUBX-L/CUBX-E User’s Manual
3. HARDWARE SETUP
11) IDE Activity LED (2-pin IDELED)
This connector supplies power to the cabinet’s IDE activity LED. Read and
write activity by devices connected to the Primary or Secondary IDE connectors
will cause the LED to light up.
TIP: If the case-mounted LED does not light,
try reversing the 2-pin plug.
IDELED
CUBX-L/CUBX-E IDE Activity LED
12) CPU, Power Supply, Chassis Fan Connectors
(3-pin CPU_FAN, PWR_FAN, CHA_FAN)
These connectors support cooling fans of 350mA (4.2 Watts) or less. Orientate
the fans so that the heat sink fins allow airflow to go across the onboard heat
sink(s) instead of the expansion slots. Depending on the fan manufacturer, the
wiring and plug may be different. The red wire should be positive, while the
black should be ground. Connect the fan’s plug to the board taking into consid-
eration the polarity of the connector.
NOTE: The “Rotation” signal is to be used only by a specially designed fan with
rotation signal. The Rotations per Minute (RPM) can be monitored usingASUS PC
Probe (see 6. SOFTWARE REFERENCE) or Intel LDCM Utility.
WARNING! The CPU and/or motherboard will overheat if there is no airflow
across the CPU and onboard heatsinks. Damage may occur to the motherboard
and/or the CPU fan if these pins are incorrectly used. These are not jumpers,
do not place jumper caps over these pins.
CPU_FAN
PWR_FAN
Rotation
+12V
CHA_FAN
GND
CUBX-L/CUBX-E 12Volt Cooling Fan Power
ASUS CUBX-L/CUBX-E User’s Manual
35
3. HARDWARE SETUP
13) Infrared Module Connector (5-pin IR)
This connector supports an optional wireless transmitting and receiving infrared
module. This module mounts to a small opening on system cases that support
this feature. You must also configure the setting through UART2 Use Infrared
(see 4.4.2 I/O Device Configuration) to select whether UART2 is directed for
use with COM2 or IrDA. Use the five pins as shown in Back View and connect
a ribbon cable from the module to the motherboard’s IR connector according to
the pin definitions.
Back View
Front View
IR
+5V
IRTX
GND
(NC)
IRRX
For the infrared feature to be available,
you must connect the optional Infrared
(IrDA) module to the motherboard.
CUBX-L/CUBX-E Infrared Module Connector
14) SMBus Connector (5-1 pin SMB)
This connector allows you to connect SMBus (System Management Bus) de-
vices. SMBus devices communicate by means of the SMBus with an SMBus
host and/or other SMBus devices. SMBus is a specific implementation of an I2C
bus, which is a multi-device bus; that is, multiple chips can be connected to the
same bus and each one can act as a master by initiating data transfer.
1
SMB
CUBX-L/CUBX-E SMBus Connector
36
ASUS CUBX-L/CUBX-E User’s Manual
3. HARDWARE SETUP
15) USB Headers (10-1 pin USB2, 5-1 pin USB3A)
If the USB port connectors on the back panel are inadequate, two USB headers
are available for three additional USB port connectors. Connect a 3-port USB
connector set to these headers and mount it to an open slot on your chassis.
1
6
5
USB2
10
1
USB3A
CUBX-E USB Headers
ASUS CUBX-L/CUBX-E User’s Manual
37
3. HARDWARE SETUP
16) ATX Power Supply Connector (20-pin block ATXPWR)
This connector connects to an ATX power supply. The plug from the power sup-
ply will only insert in one orientation because of the different hole sizes. Find the
proper orientation and push down firmly making sure that the pins are aligned.
IMPORTANT: Make sure that yourATX power supply can supply at least 10mA
on the +5-volt standby lead (+5VSB). You may experience difficulty in power-
ing ON your system if your power supply cannot support the load. For Wake-
On-LAN support, your ATX power supply must supply at least 720mA +5VSB.
ATXPWR
CUBX-L/CUBX-E ATX Power Connector
17) Power Supply Thermal Sensor Connector (2-pin block JTPWR)
If you have a power supply with thermal monitoring, connect its thermal sensor
cable to this connector.
JTPWR
Power Supply Thermal Sensor Connector
CUBX-L/CUBX-E Thermal Sensor Connector
38
ASUS CUBX-L/CUBX-E User’s Manual
3. HARDWARE SETUP
The following PANEL illustration is used for items 18–24.
*
Requires an ATX power supply.
Speaker
Connector
Keyboard Lock
Power LED
Message LED
Reset SW
ATX Power Switch*
SMI Lead
CUBX-L/CUBX-E System Panel Connections
18) System Power LED Lead (3-pin PWR.LED)
This 3-pin connector connects to the system power LED, which lights when the
system is powered on and blinks when it is in sleep or soft-off mode.
19) Keyboard Lock Switch Lead (2-pin KEYLOCK)
This 2-pin connector connects to the case-mounted key switch to allow keyboard
locking. NOTE: When the keyboard is locked, the mouse can still be used.
20) System Warning Speaker Connector (4-pin SPEAKER)
This 4-pin connector connects to the case-mounted speaker.
21) System Message LED Lead (2-pin MSG.LED)
This indicates whether a message has been received from a fax/modem. The
LED will remain lit when there is no signal and blink when there is data re-
ceived. This function requires an ACPI OS and driver support.
22) System Management Interrupt Lead (2-pin SMI)
This allows the user to manually place the system into a suspend mode or “Green”
mode where system activity will be instantly decreased to save electricity and
expand the life of certain components when the system is not in use. This 2-pin
connector (see the preceding figure) connects to the case-mounted suspend switch.
23) ATX Power Switch / Soft-Off Switch Lead (2-pin PWR.SW)
The system power is controlled by a momentary switch connected to this lead.
Pushing the button once will switch the system between ON and SLEEP or ON
and SOFT OFF, depending on your BIOS or OS setting. Pushing the switch
while in the ON mode for more than 4 seconds will turn the system off. The
system power LED shows the status of the system’s power.
24) Reset Switch Lead (2-pin RESET)
This 2-pin connector connects to the case-mounted reset switch for rebooting
your computer without having to turn off your power switch. This is a preferred
method of rebooting to prolong the life of the system’s power supply.
ASUS CUBX-L/CUBX-E User’s Manual
39
3. HARDWARE SETUP
(This page was intentionally left blank.)
40
ASUS CUBX-L/CUBX-E User’s Manual
3. HARDWARE SETUP
3.9 Starting Up the First Time
1. After all connections are made, close the system case cover.
2. Be sure that all switches are off (in some systems, marked with ).
3. Connect the power supply cord into the power supply located on the
back of your system case according to your system user’s manual.
4. Connect the power cord into a power outlet that is equipped with a surge
protector.
5. You may then turn on your devices in the following order:
a. Your monitor
b. External SCSI devices (starting with the last device on the chain)
c. Your system power. For ATX power supplies, you need to switch on
the power supply as well as press the ATX power switch on the front
of the case.
6. The power LED on the front panel of the system case will light. For
ATX power supplies, the system LED will light when the ATX power
switch is pressed. The LED on the monitor may light up or switch be-
tween orange and green after the system’s if it complies with “green”
standards or if it has a power standby feature. The system will then run
power-on tests. While the tests are running, the BIOS will alarm beeps
or additional messages will appear on the screen. If you do not see any-
thing within 30 seconds from the time you turn on the power, the system
may have failed a power-on test. Recheck your jumper settings and con-
nections or call your retailer for assistance.
Award BIOS Beep Codes
Beep
Meaning
One short beep when
displaying logo
No error during POST
Long beeps in an endless loop
One long beep followed by
three short beeps
No DRAM installed or detected
Video card not found or video card
memory bad
High frequency beeps when
system is working
CPU overheated
System running at a lower frequency
ASUS CUBX-L\CUBX-E User’s Manual
41
4. BIOS SETUP
4.1 Managing and Updating Your BIOS
4.1.1 Upon First Use of the Computer System
It is recommended that you save a copy of the original motherboard BIOS
along with a Flash Memory Writer utility (AFLASH.EXE) to a bootable
floppy disk in case you need to reinstall the BIOS later. AFLASH.EXE is a
Flash Memory Writer utility that updates the BIOS by uploading a new
BIOS file to the programmable flash ROM on the motherboard. This file
works only in DOS mode. To determine the BIOS version of your mother-
board, check the last four numbers of the code displayed on the upper left-
hand corner of your screen during bootup. Larger numbers represent a newer
BIOS file.
1. Type FORMAT A:/S at the DOS prompt to create a bootable system
floppy disk. DO NOT copy AUTOEXEC.BAT & CONFIG.SYS to the
disk.
2. Type COPYD:\AFLASH\AFLASH.EXEA:\ (assuming D is your CD-
ROM drive) to copy AFLASH.EXE to the just created boot disk.
NOTE: AFLASH works only in DOS mode. It will not work with DOS
prompt in Windows and will not work with certain memory drivers that
may be loaded when you boot from your hard drive. It is recommended
that you reboot using a floppy.
3. Reboot your computer from the floppy disk. NOTE: BIOS setup must
specify “Floppy” as the first item in the boot sequence.
4. In DOS mode, type A:\AFLASH <Enter> to run AFLASH.
IMPORTANT! If “unknown” is displayed after Flash Memory:, the memory
chip is either not programmable or is not supported by theACPI BIOS and there-
fore, cannot be programmed by the Flash Memory Writer utility.
42
ASUS CUBX-L\CUBX-E User’s Manual
4. BIOS SETUP
5. Select 1. Save Current BIOS to File from the Main menu and press
<Enter>. The Save Current BIOS To File screen appears.
6. Type a filename and the path, for example, A:\XXX-XX.XXX and then
press <Enter>.
4.1.2 Updating BIOS Procedures (only when necessary)
1. Download an updated ASUS BIOS file from the Internet (WWW or
FTP) (see ASUS CONTACT INFORMATION on page 3 for details)
and save to the disk you created earlier.
2. Boot from the disk you created earlier.
3. At the “A:\” prompt, type AFLASH and then press <Enter>.
4. At the Main Menu, type 2 and then press <Enter>. The Update BIOS
Including Boot Block and ESCD screen appears.
5. Type the filename of your new BIOS and the path, for example, A:\XXX-
XX.XXX, and then press <Enter>.
NOTE: To cancel this operation, press <Enter>.
ASUS CUBX-L\CUBX-E User’s Manual
43
4. BIOS SETUP
6. When prompted to confirm the BIOS update, press Y to start the update.
7. The utility starts to program the new BIOS information into the flash
ROM. The boot block will be updated automatically only when neces-
sary. This will minimize the chance of a failed updating. When the pro-
gramming is finished, Flashed Successfully will be displayed.
8. Follow the onscreen instructions to continue.
WARNING! If you encounter problems while updating the new BIOS,
DO NOT turn off your system since this might prevent your system from
booting up. Just repeat the process, and if the problem still persists, up-
date the original BIOS file you saved to disk above. If the Flash Memory
Writer utility was not able to successfully update a complete BIOS file,
your system may not be able to boot up. If this happens, your system will
need servicing.
44
ASUS CUBX-L\CUBX-E User’s Manual
4. BIOS SETUP
4.2 BIOS Setup Program
This motherboard supports a programmable EEPROM that can be updated using
the provided utility as described in 4.1 Managing and Updating Your BIOS.
The utility is used if you are installing a motherboard, reconfiguring your system,
or prompted to “Run Setup”. This section describes how to configure your system
using this utility.
Even if you are not prompted to use the Setup program, at some time in the future
you may want to change the configuration of your computer. For example, you
may want to enable the Security Password Feature or make changes to the power
management settings. It will then be necessary to reconfigure your system using
the BIOS Setup program so that the computer can recognize these changes and
record them in the CMOS RAM of the EEPROM.
The EEPROM on the motherboard stores the Setup utility. When you start up the
computer, the system provides you with the opportunity to run this program. This
appears during the Power-On Self Test (POST). Press <Delete> to call up the Setup
utility. If you are a little bit late in pressing the mentioned key, POST will continue
with its test routines, thus preventing you from calling up Setup. If you still need to
call Setup, restart the system by pressing <Ctrl> + <Alt> + <Delete>, or by press-
ing the Reset button on the system chassis. You can also restart by turning the
system off and then back on again. But do so only if the first two methods fail.
The Setup program has been designed to make it as easy to use as possible. It is a
menu-driven program, which means you can scroll through the various sub-menus
and make your selections among the predetermined choices.
To access the BIOS Setup program, press the <Delete> key after
the computer has run through its POST.
NOTE: Because the BIOS software is constantly being updated, the following
BIOS screens and descriptions are for reference purposes only and may not re-
flect your BIOS screens exactly.
ASUS CUBX-L\CUBX-E User’s Manual
45
4. BIOS SETUP
4.2.1 BIOS Menu Bar
The top of the screen has a menu bar with the following selections:
MAIN Use this menu to make changes to the basic system configuration.
ADVANCED Use this menu to enable and make changes to the advanced
features.
POWER
BOOT
EXIT
Use this menu to configure and enable Power Management
features.
Use this menu to configure the default system device used to lo-
cate and load the Operating System.
Use this menu to exit the current menu or specify how to exit the
Setup program.
To access the menu bar items, press the right or left arrow key on the keyboard
until the desired item is highlighted.
4.2.2 Legend Bar
At the bottom of the Setup screen you will notice a legend bar. The keys in the
legend bar allow you to navigate through the various setup menus. The following
table lists the keys found in the legend bar with their corresponding alternates and
functions.
Navigation Key(s)
<F1> or <Alt + H>
Function Description
Displays the General Help screen from anywhere in the BIOS
Setup
<Esc>
Jumps to the Exit menu or returns to the main menu from a sub-
menu
← or → (keypad arrow) Selects the menu item to the left or right
↑ or ↓ (keypad arrows) Moves the highlight up or down between fields
- (minus key)
Scrolls backward through the values for the highlighted field
+ (plus key) or spacebar Scrolls forward through the values for the highlighted field
<Enter>
Brings up a selection menu for the highlighted field
Moves the cursor to the first field
<Home> or <PgUp>
<End> or <PgDn>
Moves the cursor to the last field
<F5>
Resets the current screen to its Setup Defaults
Saves changes and exits Setup
<F10>
46
ASUS CUBX-L\CUBX-E User’s Manual
4. BIOS SETUP
General Help
In addition to the Item Specific Help window, the BIOS setup program also pro-
vides a General Help screen. This screen can be called up from any menu by sim-
ply pressing <F1> or the <Alt> + <H> combination. The General Help screen lists
the legend keys with their corresponding alternates and functions.
Saving Changes and Exiting the Setup Program
See 4.7 Exit Menu for detailed information on saving changes and exiting the
setup program.
Scroll Bar
When a scroll bar appears to the right of a help window, it indicates that there is
more information to be displayed that will not fit in the window. Use <PgUp> and
<PgDn> or the up and down arrow keys to scroll through the entire help docu-
ment. Press <Home> to display the first page, press <End> to go to the last page.
To exit the help window, press <Enter> or <Esc>.
Sub-Menu
Note that a right pointer symbol (as shown in the left view)
appears to the left of certain fields. This pointer indicates that
a sub-menu can be launched from this field. A sub-menu con-
tains additional options for a field parameter. To call up a sub-
menu, simply move the highlight to the field and press <En-
ter>. The sub-menu will then immediately appear. Use the leg-
end keys to enter values and move from field to field within a
sub-menu just as you would within a menu. Use the <Esc> key to return to the
main menu.
Take some time to familiarize yourself with each of the legend keys and their
corresponding functions. Practice navigating through the various menus and sub-
menus. If you accidentally make unwanted changes to any of the fields, use the set
default hot key <F5>. While moving around through the Setup program, note that
explanations appear in the Item Specific Help window located to the right of each
menu. This window displays the help text for the currently highlighted field.
NOTE: The item heading in square brackets represents the default setting for
that field.
ASUS CUBX-L\CUBX-E User’s Manual
47
4. BIOS SETUP
4.3 Main Menu
When the Setup program is accessed, the following screen appears:
System Time [XX:XX:XX]
Sets your system to the time that you specify (usually the current time).
The format is hour, minute, second. Valid values for hour, minute and sec-
ond are Hour: (00 to 23), Minute: (00 to 59), Second: (00 to 59). Use the
<Tab> or <Shift> + <Tab> keys to move between the hour, minute, and
second fields.
System Date [XX/XX/XXXX]
Sets your system to the date that you specify (usually the current date). The
format is month, day, year. Valid values for month, day, and year are Month:
(1 to 12), Day: (1 to 31), Year: (100 year range). Use the <Tab> or <Shift>
+ <Tab> keys to move between the month, day, and year fields.
Legacy Diskette A [1.44M, 3.5 in.], Legacy Diskette B [None]
Sets the type of floppy drives installed. Configuration options: [None]
[360K, 5.25 in.] [1.2M , 5.25 in.] [720K , 3.5 in.] [1.44M, 3.5 in.]
[2.88M, 3.5 in.]
Floppy 3 Mode Support [Disabled]
This is required to support older Japanese floppy drives. Floppy 3 Mode
support will allow reading and writing of 1.2MB (as opposed to 1.44MB)
on a 3.5-inch diskette. Configuration options: [Disabled] [Drive A]
[Drive B] [Both]
48
ASUS CUBX-L\CUBX-E User’s Manual
4. BIOS SETUP
4.3.1 Primary & Secondary Master/Slave
NOTE: Before attempting to configure a hard disk drive, make sure you
have the configuration information supplied by the manufacturer of the
drive. Incorrect settings may cause your system to not recognize the in-
stalled hard disk. To allow the BIOS to detect the drive type automati-
cally, select [Auto].
Type [Auto]
Select [Auto] to automatically detect an IDE hard disk drive. If automatic
detection is successful, the correct values will be filled in for the remaining
fields on this sub-menu. If automatic detection fails, your hard disk drive
may be too old or too new. You can try updating your BIOS or enter the
IDE hard disk drive parameters manually.
NOTE: After the IDE hard disk drive information has been entered into
BIOS, new IDE hard disk drives must be partitioned (such as with FDISK)
and then formatted before data can be read from and write on. Primary
IDE hard disk drives must have its partition set to active (also possible
with FDISK).
Other options for the Type field are:
[None] - to disable IDE devices
ASUS CUBX-L\CUBX-E User’s Manual
49
4. BIOS SETUP
IMPORTANT: If your hard disk was already formatted on an older previous system,
incorrect parameters may be detected. You will need to enter the correct parameters
manually or use low-level format if you do not need the data stored on the hard disk.
If the parameters listed differ from the ones used when the disk was formatted, the
disk will not be readable. If the auto-detected parameters do not match the ones that
should be used for your disk, you should enter the correct ones manually by setting
[User Type HDD].
[User Type HDD]
Manually enter the number of cylinders, heads and sectors per track for your drive.
Refer to your drive documentation or look on the drive for this information. If no
drive is installed or if you are removing a drive and not replacing it, select [None].
Translation Method [LBA]
Select the hard disk drive type in this field. When Logical Block Addressing is
enabled, 28-bit addressing of the hard drive is used without regard for cylinders,
heads, or sectors. Note that Logical Block Access may decrease the access speed
of the hard disk. However, LBA Mode is necessary for drives with greater than
504MB in storage capacity. Configuration options: [LBA] [LARGE] [Normal]
[Match Partition Table] [Manual]
Cylinders
This field configures the number of cylinders. Refer to your drive documentation
to determine the correct value to enter into this field. NOTE: To make changes to
this field, the Type field must be set to [User Type HDD] and the Translation
Method field must be set to [Manual].
50
ASUS CUBX-L\CUBX-E User’s Manual
4. BIOS SETUP
Head
This field configures the number of read/write heads. Refer to your drive documenta-
tion to determine the correct value to enter into this field. NOTE: To make changes to
this field, the Type field must be set to [User Type HDD] and the Translation Method
field must be set to [Manual].
Sector
This field configures the number of sectors per track. Refer to your drive docu-
mentation to determine the correct value to enter into this field. NOTE: To make
changes to this field, the Type field must be set to [User Type HDD] and the Trans-
lation Method field must be set to [Manual].
CHS Capacity
This field shows the drive’s maximum CHS capacity calculated automatically by
the BIOS from the drive information you entered.
Maximum LBA Capacity
This field shows the drive’s maximum LBA capacity calculated automatically by
the BIOS from the drive information you entered.
Multi-Sector Transfers [Maximum]
This option automatically sets the number of sectors per block to the highest number
supported by the drive. This field can also be configured manually. Note that when
this field is automatically configured, the set value may not always be the fastest
value for the drive. Refer to the documentation that came with your hard drive to
determine the optimal value and set it manually. NOTE: To make changes to this
field, the Type field must be set to [User Type HDD]. Configuration options: [Dis-
abled] [2 Sectors] [4 Sectors] [8 Sectors] [16 Sectors] [32 Sectors] [Maximum]
SMART Monitoring [Disabled]
This allows the enabling or disabling of the S.M.A.R.T. (Self-Monitoring, Analy-
sis and Reporting Technology) system which utilizes internal hard disk drive moni-
toring technology. This feature is normally disabled because system resources used
in this feature may decrease system performance. Configuration options: [Dis-
abled] [Enabled]
PIO Mode [4]
This option lets you set a PIO (Programmed Input/Output) mode for the IDE de-
vice. Modes 0 through 4 provide successively increased performance. Configura-
tion options: [0] [1] [2] [3] [4]
ULTRA DMA Mode [Disabled]
Ultra DMA capability allows improved transfer speeds and data integrity for com-
patible IDE devices. Set to [Disabled] to suppress Ultra DMA capability. NOTE:
To make changes to this field, the Type field must be set to [User Type HDD].
Configuration options: [0] [1] [2] [3] [4] [Disabled]
ASUS CUBX-L\CUBX-E User’s Manual
51
4. BIOS SETUP
Other options for “Type:” are:
[CD-ROM] - for IDE CD-ROM drives
[LS-120] - for LS-120 compatible floppy disk drives
[ZIP-100] - for ZIP-100 compatible disk drives
[MO] - for IDE magneto optical disk drives
[Other ATAPI Device] - for IDE devices not listed here
After using the legend keys to make your selections on this sub-menu, press
the <Esc> key to exit back to the Main menu. When the Main menu ap-
pears, you will notice that the drive size appear in the field for the hard disk
drive that you just configured.
4.3.2 Keyboard Features
Boot Up NumLock Status [On]
This field enables users to activate the Number Lock function upon system
boot. Configuration options: [Off] [On]
Keyboard Auto-Repeat Rate [12/Sec]
This controls the speed at which the system registers repeated keystrokes.
Options range from 6 to 30 characters per second. Configuration options:
[6/Sec] [8/Sec] [10/Sec] [12/Sec] [15/Sec] [20/Sec] [24/Sec] [30/Sec]
Keyboard Auto-Repeat Delay [1/4 Sec]
This field sets the time interval for displaying the first and second charac-
ters. Configuration options: [1/4 Sec] [1/2 Sec] [3/4 Sec] [1 Sec]
52
ASUS CUBX-L\CUBX-E User’s Manual
4. BIOS SETUP
Language [English]
This allows selection of the BIOS’ displayed language. Configuration options:
[English]
Supervisor Password [Disabled], User Password [Disabled]
This field allows you to set the password. To set the password, highlight the appro-
priate field and press <Enter>.
Type in a password and press <Enter>. You can type up to eight alphanumeric char-
acters. Symbols and other keys are ignored. To confirm the password, type the pass-
word again and press the <Enter>. The password is now set to [Enabled]. This pass-
word allows full access to the BIOS Setup menus.
To clear the password, highlight this field and press <Enter>. The same dialog box
as above will appear. Press <Enter> and the password will be set to [Disabled].
A Note about Passwords
The BIOS Setup program allows you to specify passwords in the Main menu. The
passwords control access to the BIOS and certain security menu options during sys-
tem startup. The passwords are not case sensitive. In other words, it makes no differ-
ence whether you enter a password using upper or lowercase letters.
The BIOS Setup program allows you to specify two separate passwords: a Supervisor
password and a User password. When disabled, anyone may access all BIOS Setup
program functions. When enabled, the Supervisor password is required for entering
the BIOS Setup program and having full access to all menu options.
Forgot the password?
If you forgot the password, you can clear the password by erasing the CMOS
Real Time Clock (RTC) RAM. The RAM data containing the password
information is powered by the onboard button cell battery. To erase the
RTC RAM: (1) Unplug your computer, (2) Short the solder points, (3) Turn
ON your computer, (4) Hold down <Delete> during bootup and enter BIOS
setup to re-enter user preferences.
Intel
CLRTC
Short solder points
PIIX4E
to Clear CMOS
C297
PCIset
CUBX-L/CUBX-E Clear RTC RAM
Halt On [All Errors]
This field determines which types of errors will cause the system to halt.
Configuration options: [All Errors] [No Error] [All but Keyboard] [All but
Disk] [All but Disk/Keyboard]
Installed Memory [XXX MB]
This field displays the amount of conventional memory detected by the
system during bootup. You do not need to make changes to this field. This
is a display only field.
ASUS CUBX-L\CUBX-E User’s Manual
53
4. BIOS SETUP
4.4 Advanced Menu
CPU Speed [Manual]
When the motherboard is set to JumperFree mode (see 3.4 Motherboard
Settings), this field allows you to select the internal speed of your CPU.
Available options include multiples of 66 and 100. Select [Manual] if you
want to make changes to the subsequent 2 fields. Note that selecting a fre-
quency higher than the CPU manufacturer recommends may cause the sys-
tem to hang or crash. See System Hangup later in this section.
CPU Core:Bus Freq. Multiple (when CPU Speed is set to [Manual])
This field is for unlocked processors only. This sets the frequency multiple
between the CPU’s internal frequency and external frequency. This must be
set in conjunction with CPU Bus/PCI Frequency to match the speed of
your CPU. Configuration options vary according to the external frequency
of your CPU.
CPU Bus/PCI Freq. (MHz)
(when CPU Speed is set to [Manual])
This feature tells the clock generator what frequencies to
send to the local bus and PCI devices onboard. The bus fre-
quency (external frequency) multiplied by the bus multiple
equals the CPU’s internal frequency (the CPU speed).
54
ASUS CUBX-L\CUBX-E User’s Manual
4. BIOS SETUP
CPU Vcore
This field displays the core voltage supplied
to the CPU. If you want to set it manually, al-
ways refer to the CPU documentation for the
reasonable voltage range.
Using Celeron
processors
Using Pentium III
processors
CPU Level 1 Cache, CPU Level 2 Cache [Enabled]
These fields allow you to choose from the default of [Enabled] or choose
[Disabled] to turn on or off the CPU’s Level 1 and Level 2 built-in cache.
Configuration options: [Disabled] [Enabled]
CPU Level 2 Cache ECC Check [Disabled]
This function controls the ECC capability in the CPU level 2 cache. Con-
figuration options: [Disabled] [Enabled]
Processor Serial Number [Disabled]
The Processor Serial Number is a unique number that is added to every
Pentium III processor to help verify the identity of the user across the Internet.
Set this field to [Enabled] when you need increased security for doing busi-
ness online or e-commerce. Otherwise, leave it to its default setting of [Dis-
abled] for greater anonymity when surfing the Internet. NOTE: This field
is available only when a Pentium III processor is installed in your system.
BIOS Update [Enabled]
This functions as an update loader integrated into the BIOS to supply the
processor with the required data. In the default position of [Enabled], the
BIOS will load the update on all processors during system bootup. Configu-
ration options: [Disabled] [Enabled]
PS/2 Mouse Function Control [Auto]
The default of [Auto] allows the system to detect a PS/2 mouse on startup.
If detected, IRQ12 will be used for the PS/2 mouse. IRQ12 will be reserved
for expansion cards only if a PS/2 mouse is not detected. [Enabled] will
always reserve IRQ12, whether on startup a PS/2 mouse is detected or not.
Configuration options: [Enabled] [Auto]
USB Legacy Support [Auto]
The default of [Auto] allows the system to detect a USB device on startup. If
detected, USB controller legacy mode will be enabled. If not detected, USB
controller legacy mode will be disabled. When this field is set to [Disabled],
USB controller legacy mode is disabled no matter whether you are using a
USB device or not. Configuration options: [Disabled] [Enabled] [Auto]
OS/2 Onboard Memory > 64M [Disabled]
When using OS/2 operating systems with installed DRAM of greater than
64MB, you need to set this option to [Enabled]; otherwise, leave this on
[Disabled]. Configuration options: [Disabled] [Enabled]
ASUS CUBX-L\CUBX-E User’s Manual
55
4. BIOS SETUP
Notes for JumperFree Mode
CPU Upgrade/Reinstallation
To ensure that your system can enter BIOS setup after the processor has
been changed or reinstalled, your system will start up running at a bus speed
of 66MHz and a fail-safe CPU speed (4x66MHz for the Intel Coppermine
processor or 2x66MHz for non-Coppermine processors). It will then auto-
matically take you to the Advanced menu with a popup menu of all the
officially possible CPU speeds.
For processors with locked frequency multiplier
For processors with unlocked frequency multiplier
56
ASUS CUBX-L\CUBX-E User’s Manual
4. BIOS SETUP
System Hangup
If your system crashes or hangs due to improper CPU settings, power OFF
your system and restart. The system will start up in safe mode running at a
bus speed of 66MHz and enter BIOS setup.
Cause for Hangup: Improper CPU Speed
Cause for Hangup: Improper CPU Bus/PCI Freq. (MHz)
ASUS CUBX-L\CUBX-E User’s Manual
57
4. BIOS SETUP
4.4.1 Chip Configuration
(Scroll down to see more items as shown.)
SDRAM Configuration [By SPD]
This sets the optimal timings for items 2–5, depending on the memory mod-
ules that you are using. The default setting is [By SPD], which configures
items 2–5 by reading the contents in the SPD (Serial Presence Detect) de-
vice. The EEPROM on the memory module stores critical parameter infor-
mation about the module, such as memory type, size, speed, voltage inter-
face, and module banks. Configuration options: [User Define] [7ns
(143MHz)] [8ns (125MHz)] [By SPD]
SDRAM CAS Latency
This controls the latency between the SDRAM read command and the time
that the data actually becomes available. NOTE: To make changes to this
field, the SDRAM Configuration field must be set to [User Define].
SDRAM RAS to CAS Delay
This controls the latency between the SDRAM active command and the
read/write command. NOTE: To make changes to this field, the SDRAM
Configuration field must be set to [User Define].
SDRAM RAS Precharge Time
This controls the idle clocks after issuing a precharge command to the
SDRAM. NOTE: To make changes to this field, the SDRAM Configura-
tion field must be set to [User Define].
DRAM Idle Timer
This controls the amount of time in HCLKs that the DRAM controller waits
to close a DRAM page after the CPU becomes idle. Leave on default set-
ting. NOTE: To make changes to this field, the SDRAM Configuration
field must be set to [User Define].
58
ASUS CUBX-L\CUBX-E User’s Manual
4. BIOS SETUP
SDRAM MA Wait State [Normal]
This controls the leadoff clocks for CPU read cycles. Leave on default set-
ting. Configuration options: [Fast] [Normal] [Slow]
Snoop Ahead [Enabled]
[Enabled] allows PCI streaming. Configuration options: [Enabled] [Disabled]
Host Bus Fast Data Ready [Disabled]
Configuration options: [Disabled] [Enabled]
16-bit I/O Recovery Time [1 BUSCLK]
Configuration options: [4 BUSCLK] [1 BUSCLK] [2 BUSCLK] [3 BUSCLK]
8-bit I/O Recovery Time [1 BUSCLK]
Configuration options: [8 BUSCLK] [1 BUSCLK] [2 BUSCLK] [3 BUSCLK]
[4 BUSCLK] [5 BUSCLK] [6 BUSCLK] [7 BUSCLK]
Graphics Aperture Size [64MB]
This feature allows you to select the size of mapped memory forAGPgraphic data.
Configurationoptions:[4MB][8MB][16MB][32MB][64MB][128MB][256MB]
Video Memory Cache Mode [UC]
USWC (uncacheable, speculative write combining) is a cache technology
for the video memory of the processor. It can greatly improve the display
speed by caching the display data. You must set this to UC (uncacheable) if
your display card cannot support this feature; otherwise your system may
not boot. Configuration options: [UC] [USWC]
PCI 2.1 Support [Enabled]
This function allows you to enable or disable PCI 2.1 features including passive
release and delayed transaction. Configuration options: [Disabled] [Enabled]
Memory Hole At 15M-16M [Disabled]
This field allows you to reserve an address space for ISA expansion cards
that require it. Configuration options: [Disabled] [Enabled]
Onboard PCI IDE Enable [Both]
You can select to enable the primary IDE channel, secondary IDE channel,
both, or disable both channels. Configuration options: [Both] [Primary] [Sec-
ondary] [Disabled]
Onboard PCI ATA Chip Enable [Enabled] (for CUBX-E only)
This controls the UltraDMA/100 controller on the motherboard. You may
disable it if you do not want to use UltraDMA100/66 mode. Configuration
options: [Disabled] [Enabled]
ASUS CUBX-L\CUBX-E User’s Manual
59
4. BIOS SETUP
4.4.2 I/O Device Configuration
Onboard FDC Swap A & B [No Swap]
This field allows you to reverse the hardware drive letter assignments of
your floppy disk drives. Configuration options: [No Swap] [Swap AB]
Floppy Disk Access Control [R/W]
When set to [Read Only], this field protects files from being copied to floppy
disks by allowing reads from the floppy disk drive but not writes. The setup
default [R/W] allows both reads and writes. Configuration options: [R/W]
[Read Only]
Onboard Serial Port 1 [3F8H/IRQ4], Onboard Serial Port 2 [2F8H/IRQ3]
These fields allow you to set the addresses for the onboard serial connec-
tors. Serial Port 1 and Serial Port 2 must have different addresses. Con-
figuration options: [3F8H/IRQ4] [2F8H/IRQ3] [3E8H/IRQ4] [2E8H/
IRQ10] [Disabled]
UART2 Use Infrared [Disabled]
When enabled, this field activates the onboard infrared feature and sets the
second serial UART to support the infrared module connector on the moth-
erboard. If your system already has a second serial port connected to the
onboard COM2 connector, it will no longer work if you enable the infrared
feature. See IrDA-Compliant Infrared Module Connector in 3.8 Exter-
nal Connectors. Configuration options: [Disabled] [Enabled]
60
ASUS CUBX-L\CUBX-E User’s Manual
4. BIOS SETUP
Onboard Parallel Port [378H/IRQ7]
This field sets the address of the onboard parallel port connector. If you
disable this feature, Parallel Port Mode and ECP DMA Select configu-
rations will not be available. Configuration options: [Disabled] [378H/
IRQ7] [278H/IRQ5]
Parallel Port Mode [ECP+EPP]
This field allows you to set the operation mode of the parallel port. [Nor-
mal] allows normal-speed operation but in one direction only; [EPP] al-
lows bidirectional parallel port operation; [ECP] allows the parallel port
to operate in bidirectional DMA mode; [ECP+EPP] allows normal speed
operation in a two-way mode. Configuration options: [Normal] [EPP]
[ECP] [ECP+EPP]
ECP DMA Select [3]
This field allows you to configure the parallel port DMA channel for the
selected ECP mode. This selection is available only if you select [ECP] or
[ECP+EPP] in Parallel Port Mode above. Configuration options: [1] [3]
[Disabled]
ASUS CUBX-L\CUBX-E User’s Manual
61
4. BIOS SETUP
4.4.3 PCI Configuration
Slot 1 IRQ, Slot 2 IRQ, Slot 3/6 IRQ, Slot 4/5 IRQ [Auto]
These fields set how IRQ use is determined for each PCI slot. The default
setting for each field is [Auto], which uses auto-routing to determine IRQ
use. Configuration options: [Auto] [NA] [3] [4] [5] [7] [9] [10] [11] [12]
[14] [15]
PCI/VGA Palette Snoop [Disabled]
Some nonstandard VGAcards, such as graphics accelerators or MPEG Video
Cards, may not show colors properly. The setting [Enabled] should correct
this problem. Otherwise, leave this on the default setting of [Disabled].
Configuration options: [Disabled] [Enabled]
PCI Latency Timer [32]
Leave on default setting for best performance vs. stability.
SYMBIOS SCSI BIOS [Auto]
[Auto] allows the motherboard’s BIOS to detect whether you have a Symbios
SCSI card. If the Symbios SCSI card is detected, the motherboard’s Symbios
BIOS will be enabled; if no Symbios SCSI card is detected, the onboard
Symbios SCSI BIOS will be disabled.
[Disabled] will disable the motherboard’s Symbios SCSI BIOS so that the
BIOS on an external Symbios SCSI card can be used. If your Symbios SCSI
card does not have a BIOS, the Symbios SCSI card will not function. Con-
figuration options: [Auto] [Disabled]
62
ASUS CUBX-L\CUBX-E User’s Manual
4. BIOS SETUP
USB IRQ [Enabled]
[Enabled] reserves an IRQ# for the USB to work. [Disabled] does not allow
the USB to have an IRQ# and therefore prevents the USB from functioning.
If you are not using any USB devices, you may set this feature to [Disabled]
to save an extra IRQ# for expansion cards. Configuration options: [Dis-
abled] [Enabled]
Primary VGA BIOS [PCI Card]
If your computer has both PCI andAGP VGAcards, this field allows you to
select which of the cards will act as your primary graphics card. [AGP Card]
uses the AGP card as your primary card. The default, [PCI Card], allows
your PCI graphics card to take precedence when detected. Configuration
options: [PCI Card] [AGP Card]
Onboard ATA Device First [Yes]
Setting this field to [Yes] gives priority to UltraDMA/66 devices connected
to the onboard UltraDMA/66 IDE connectors over SCSI devices connected
to PCI interface SCSI cards (see also Other Boot Device in 4.6 Boot Menu).
Configuration options: [Yes] [No]
PCI/PNP ISA IRQ Resource Exclusion
IRQ XX Used By ISA [No/ICU]
These fields indicate whether or not the displayed IRQ for each field is
being used by a legacy (non-PnP) ISA card. The default value indicates
either that the displayed IRQ is not used or that ISA Configuration Utility
(ICU) is being used to determine if an ISA card is using that IRQ. If you
install a legacy ISA card that requires a unique IRQ and you are not using an
ICU, you must set the field for that IRQ to [Yes]. For example: If you install
a legacy ISA card that requires IRQ 10, then set IRQ10 Used By ISA to
[Yes]. Configuration options: [No/ICU] [Yes]
ASUS CUBX-L\CUBX-E User’s Manual
63
4. BIOS SETUP
PCI/PNP ISA DMA Resource Exclusion
DMA x Used By ISA [No/ICU]
These fields indicate whether or not the displayed DMA channel for each
field is being used by a legacy (non-PnP) ISAcard. The default setting indi-
cates either that the displayed DMA channel is not used or an ICU is being
used to determine if an ISA card is using that channel. If you install a legacy
ISA card that requires a unique DMA channel, and you are not using an
ICU, you must set the field for that channel to [Yes]. Configuration options:
[No/ICU] [Yes]
PCI/PNP ISA UMB Resource Exclusion
64
ASUS CUBX-L\CUBX-E User’s Manual
4. BIOS SETUP
ISA MEM Block BASE [No/ICU]
This field allows you to set the base address and block size of a legacy ISA
card that uses any memory segment within the C800 and DFFF address
range. If you have such a card and you are not using an ICU to specify its
address range, select a base address from the six available options; the ISA
MEM Block SIZE field will then appear for selecting the block size. If you
have more than one legacy ISA card in your system that requires the use of
this address range, you can increase the block size to 8K, 16K, 32K, or 64K.
If you are using an ICU to accomplish this task, leave ISA MEM Block
BASE to its default setting of [No/ICU]. Configuration options: [No/ICU]
[C800] [CC00] [D000] [D400] [D800] [DC00]
4.4.4 Shadow Configuration
Video ROM BIOS Shadow [Enabled]
This field allows you to change the video BIOS location from ROM to
RAM. Relocating to RAM enhances system performance, as information
access is faster than the ROM. Configuration options: [Disabled] [Enabled]
C8000-DFFFF Shadow [Disabled]
These fields are used for shadowing other expansion card ROMs. If you
install other expansion cards with ROMs on them, you will need to know
which addresses the ROMs use to shadow them specifically. Shadowing a
ROM reduces the memory available between 640K and 1024K by the amount
used for this purpose. Configuration options: [Disabled] [Enabled]
ASUS CUBX-L\CUBX-E User’s Manual
65
4. BIOS SETUP
4.5 Power Menu
The Power menu allows you to reduce power consumption. This feature turns off the
video display and shuts down the hard disk after a period of inactivity.
Power Management [User Define]
This option must be enabled to use any of the automatic power saving features. If
this menu item is set to [Disabled], power management features will not function
regardless of other field settings on this menu. The [User Define] option allows you
to make your own selections in the Power menu. When set to [Max Saving], system
power will be conserved to its greatest amount. The Suspend Mode field will then
be set to predefined value that ensures maximum power savings.
This field acts as the master control for the power management modes. [Max Sav-
ing] puts the system into power saving mode after a brief period of system inactiv-
ity; [Min Saving] is almost the same as [Max Saving] except that the system inactiv-
ity period is longer; [Disabled] disables the power saving features; [User Define]
allows you to set power saving options according to your preference. Configuration
options: [User Define] [Disabled] [Min Saving] [Max Saving]
IMPORTANT: Advanced Power Management (APM) should be installed to keep
the system time updated when the computer enters suspend mode activated by
the BIOS Power Management. For DOS environments, you need to add the
statement, DEVICE=C:\DOS\POWER.EXE, to your CONFIG.SYS file. For
Windows 3.x and Windows 95, you need to install Windows with the APM
feature. For Windows 98 and later, APM is automatically installed. A battery
and power cord icon labeled “Power Management” will appear in the “Control
Panel.” Choose “Advanced” in the Power Management Properties dialog box.
66
ASUS CUBX-L\CUBX-E User’s Manual
4. BIOS SETUP
Video Off Option [Suspend -> Off ]
This field determines when to activate the video off feature for monitor
power management. Configuration options: [Always On] [Suspend -> Off]
Video Off Method [DPMS OFF]
This field defines the video off features. The DPMS (Display Power Man-
agement System) feature allows the BIOS to control the video display card
if it supports the DPMS feature. [Blank Screen] only blanks the screen.
(Use this for monitors without power management or “green” features. Your
screen saver will not display with [Blank Screen] selected). [V/H
SYNC+Blank] blanks the screen and turns off vertical and horizontal scan-
ning. Configuration options: [Blank Screen] [V/H SYNC+Blank] [DPMS
Standby] [DPMS Suspend] [DPMS OFF] [DPMS Reduce ON]
HDD Power Down [Disabled]
When enabled, this shuts down any IDE hard disk drives in the system
after a period of inactivity as set in this user-configurable field. This fea-
ture does not affect SCSI hard drives. Configuration options: [Disabled]
[1 Min] [2 Min] [3 Min]...[15 Min]
Suspend-to-RAM Capability [Disabled]
Suspend-to-RAM (STR) is an energy-saving feature. In Suspend-to-RAM
state, all devices on the computer are turned off, except for the system RAM.
Thus, the PC consumes less than 5 Watts of power. Select [Enabled] if your
power supply can supply at least 720mA on the +5VSB lead to support the
STR function. If the expansion cards you use on the motherboard do not
support the STR function, you must leave this field on the default setting
[Disabled]. Configuration options: [Enabled] [Disabled]
NOTE: This field is only effective for Windows 98.
Suspend Mode [Disabled]
Sets the time period before the system goes into suspend mode. NOTE:
This field is only effective for DOS, Windows 9x, and Windows NT 4.0
environments. Configuration options: [Disabled] [30 Sec] [1 Min] [2 Min]
[4 Min] [8 Min] [20 Min] [30 Min] [40 Min]
PWR Button < 4 Secs [Soft off]
When set to [Soft off], the ATX switch can be used as a normal system
power-off button when pressed for less than 4 seconds. [Suspend] allows
the button to have a dual function where pressing less than 4 seconds will
place the system in sleep mode. Regardless of the setting, holding the ATX
switch for more than 4 seconds will power off the system. NOTE: This
field is only effective in APM OS system. Configuration options: [Soft off]
[Suspend]
ASUS CUBX-L\CUBX-E User’s Manual
67
4. BIOS SETUP
4.5.1 Power Up Control
AC PWR Loss Restart [Disabled]
This allows you to set whether you want your system to reboot after the
power has been interrupted. [Disabled] leaves your system off and [En-
abled] reboots your system. [Previous State] sets your system back to the
state it is before the power interruption. Configuration options: [Disabled]
[Enabled] [Previous State]
PWR Up On External Modem Act [Disabled]
This allows either settings of [Enabled] or [Disabled] for powering up the
computer when the external modem receives a call while the computer is in
Soft-off mode. NOTE: The computer cannot receive or transmit data until
the computer and applications are fully running, thus connection cannot be
made on the first try. Turning an external modem off and then back on while
the computer is off causes an initialization string that will also cause the
system to power on. Configuration options: [Disabled] [Enabled]
Wake On LAN or PCI Modem [Disabled]
Wake-On-LAN or a PCI modem allows your computer to be booted from
another computer via network by sending a wake-up frame or signal. Con-
figuration options: [Disabled] [Enabled]
IMPORTANT: This feature requires an optional network interface with Wake-On-
LAN and an ATX power supply with at least 720mA +5V standby power.
68
ASUS CUBX-L\CUBX-E User’s Manual
4. BIOS SETUP
PWR Up On PS2 KB/Mouse [Disabled]
Select [Auto] if you wish to use your PS2 keyboard or PS2 mouse (by click-
ing on the left button) to power up your computer. The BIOS program will
then determine whether your system has an ATX power supply that can
supply at least 300mA on the +5VSB lead to support this feature. The de-
fault is set to [Disabled] because not all computers have the appropriate
ATX power supply. Configuration options: [Auto] [Disabled]
Wake Up By Keyboard [Space Bar]
When the previous setup item PWR Up On PS2 KB/Mouse is enabled,
you may specify the key(s) to press to power up the computer. Configura-
tion options: [Space Bar] [Ctrl-Esc] [Power Key]
Automatic Power Up [Disabled]
This allows an unattended or automatic system power up. You may config-
ure your system to power up at a certain time of the day by selecting [Every-
day] or at a certain time and day by selecting [By Date]. NOTE: Automatic
Power Up will not work if the system is powered down by operating sys-
tems, such as Windows 98, which have ACPI support enabled. Configura-
tion options: [Disabled] [Everyday] [By Date]
ASUS CUBX-L\CUBX-E User’s Manual
69
4. BIOS SETUP
4.5.2 Hardware Monitor
MB Temperature, CPU Temperature [xxxC/xxxF]
JTPWR Temperature [Ignore]
The onboard hardware monitor is able to detect the MB (motherboard),
CPU (for supported processors only), and power supply temperatures. Set
to [Ignore] only if necessary.
Chassis Fan [xxxxRPM]
CPU Fan [Ignore]
Power Fan Speed [xxxxRPM]
The onboard hardware monitor is able to detect the CPU fan speed, power
supply fan speed, and the chassis fan speed in rotations per minute (RPM).
The presence of the fans is automatically detected. Set to [Ignore] only if
necessary.
VCORE Voltage, +3.3V Voltage, +5V Voltage, +12V Voltage, -12V
Voltage, -5V Voltage [xx.xV]
The onboard hardware monitor is able to detect the voltage output by the
onboard voltage regulators. Set to [Ignore] only if necessary.
NOTE: If any of the monitored items is out of range, an error message will
appear: “Hardware Monitor found an error. Enter Power setup menu for
details”. You will then be prompted to “Press F1 to continue, DEL to enter
SETUP”.
70
ASUS CUBX-L\CUBX-E User’s Manual
4. BIOS SETUP
4.6 Boot Menu
Boot Sequence
The Boot menu allows you to select among the four possible types of boot
devices listed using the up and down arrow keys. By using the <+> or
<Space> key, you can promote devices and by using the <-> key, you can
demote devices. Promotion or demotion of devices alters the priority which
the system uses to search for a boot device on system power up. Configura-
tion options: [Removable Devices] [IDE Hard Drive] [ATAPI CD-ROM]
[Other Boot Device]
Removable Device [Legacy Floppy]
Configuration options: [Disabled] [Legacy Floppy] [LS120] [ZIP-100]
[ATAPI MO]
IDE Hard Drive
This field allows you to select which IDE hard disk drive to use in the boot
sequence. Pressing [Enter] will show the product IDs of all connected IDE
hard disk drives.
ATAPI CD-ROM
This field allows you to select which ATAPI CD-ROM drive to use in the
boot sequence. Pressing [Enter] will show the product IDs of all your con-
nected ATAPI CD-ROM drives.
ASUS CUBX-L\CUBX-E User’s Manual
71
4. BIOS SETUP
Other Boot Device Select [INT18 Device (Network)]
Configuration options: [Disabled] [SCSI Boot Device/Onboard ATA Boot De-
vice] [INT18 Device (Network)] [LANDesk (R) Service Agent]
IMPORTANT: The option [SCSI Boot Device/Onboard ATA Boot De-
vice] is available only on the CUBX-E model. If [SCSI/Onboard ATA
Boot Device] is selected, the system will boot from the UltraDMA/100/
66 device first if Onboard ATA Device First is set to [Yes] (see 4.4.3
PCI Configuration). Otherwise, it will boot from the SCSI device.
Plug & Play O/S [No]
This field allows you to use a Plug-and-Play (PnP) operating system to con-
figure the PCI bus slots instead of using the BIOS. When [Yes] is selected,
interrupts may be reassigned by the OS. When a non-PnP OS is installed or
you want to prevent reassigning of interrupt settings, select the default set-
ting of [No]. Configuration options: [No] [Yes]
Reset Configuration Data [No]
The Extended System Configuration Data (ESCD) contain information about
non-PnP devices. It can also hold the complete record of how the system
was configured the last time it was booted. Select [Yes] only if you want to
clear these data during the Power-On Self Test (POST). Configuration op-
tions: [No] [Yes]
Boot Virus Detection [Enabled]
This field allows you to set boot virus detection, ensuring a virus-free boot
sector. The system halts and displays a warning message when it detects a
virus. If this occurs, you can either allow the operation to continue or use a
virus-free bootable floppy disk to restart and investigate your system. Con-
figuration options: [Disabled] [Enabled]
Quick Power On Self Test [Enabled]
This feature enables you to speed up the bootup by skipping some POST
routines such as memory checking. Configuration options: [Disabled] [En-
abled]
Boot Up Floppy Seek [Enabled]
When enabled, the BIOS will seek the floppy disk drive to determine whether
the drive has 40 or 80 tracks. Floppy drives with 1.44MB have 80 tracks.
You may leave the default [Disabled] to save time if you are using 1.44MB
floppy drives. Configuration options: [Disabled] [Enabled]
Full Screen Logo [Enabled]
Configuration options: [Disabled] [Enabled]
72
ASUS CUBX-L\CUBX-E User’s Manual
4. BIOS SETUP
4.7 Exit Menu
Once you have made all of your selections from the various menus in the
Setup program, you should save your changes and exit Setup. Select Exit
from the menu bar to display the following menu:
NOTE: Pressing <Esc> does not exit this menu. You must select one of the
options from this menu or <F10> from the legend bar to exit this menu.
Exit Saving Changes
Once you are finished making your selections, choose this option from the
Exit menu to ensure the values you selected are saved to the CMOS RAM.
The CMOS RAM is sustained by an onboard backup battery and stays on
even when the PC is turned off. Once this option is selected, a confirmation
is asked. Select [Yes] to save changes and exit.
NOTE: If you attempt to exit the Setup program without saving your
changes, the program will prompt you with a message asking if you want
to save your changes before exiting. Pressing <Enter> will then save changes
while exiting.
Exit Discarding Changes
This option should only be used if you do not want to save the changes you
have made to the Setup program. If you have made changes to fields other
than system date, system time, and password, the system will ask for con-
firmation before exiting.
ASUS CUBX-L\CUBX-E User’s Manual
73
4. BIOS SETUP
Load Setup Defaults
This option allows you to load the default values for each of the parameters
on the Setup menus. When this option is selected or if <F5> is pressed, a
confirmation is requested. Select [Yes] to load default values. You can now
select Exit Saving Changes or make other changes before saving the val-
ues to the non-volatile RAM.
Discard Changes
This option allows you to discard the selections you made and restore the
values you previously saved. After selecting this option, a confirmation is
requested. Select [Yes] to discard any changes and load the previously saved
values.
Save Changes
This option saves your selections without exiting the Setup program. You
can then return to other menus and make changes. After selecting this op-
tion, all selections are saved and a confirmation is requested. Select [Yes] to
save any changes to the non-volatile RAM.
74
ASUS CUBX-L\CUBX-E User’s Manual
5. SOFTWARE SETUP
5.1 Install Operating System
You should always use the latest operating system and updates when using new
hardware to ensure full compliancy. You may use any version of Windows 98, but
for Windows 95, you must use OSR 2.0 or later. For Windows NT 4.0, you must use
Service Pack 3.0 or later.
5.2 Start Windows
When you start Windows 98 for the first time after installing your motherboard,
Windows will detect all plug-and play devices. Follow theAdd New Hardware Wiz-
ard to install all necessary device drivers. When prompted to restart, select No and
then follow the setup procedures in this section.
NOTE: Because there are various motherboard settings, options, and expansion
cards, the following can only be used as a general reference and may not be an exact
reflection of your system.
5.3 Installing Drivers and Software
5.3.1 PCI RAID Controller Found
(only on model with onboard ATA100 IDE controller)
Insert the provided floppy disk into your floppy disk drive.
(1) Click here.
(2) Click here.
(3) Select Floppy disk
drives and then
click here.
Follow the online instructions to finish installation.
ASUS CUBX-L/CUBX-E User’s Manual
75
5. SOFTWARE SETUP
5.3.2 Support CD Installation Menu
NOTE: The support CD contents are subject to change at any time without notice.
To begin using your support CD disc, just insert it into your CD-ROM drive and the
support CD installation menu should appear. If the menu does not appear, double-
click or run E:\ASSETUP.EXE (assuming that your CD-ROM drive is drive E:).
76
ASUS CUBX-L/CUBX-E User’s Manual
5. SOFTWARE SETUP
Intel LDCMAdministrator Setup (recommended): Installs software to monitor
PC systems on the network within the same bridge address with the Client soft-
ware installed. The administrator should install both Administrator and Client
software.
•
•
•
Intel LDCM Client Setup (recommended): Installs software to monitor the Cli-
ent system. The LANDesk Client Manager must be installed to use the hardware
manager features.
ASUS BIOS Flash Utility for LDCM (recommended): Installs a utility that
can remotely flash a client PC’s BIOS when used in conjunction with Intel LDCM
Administrator.
•
•
•
•
Install ASUS PC Probe Vx.xx (recommended): Installs a utility to monitor
your computer’s fan, temperature, and voltages.
Install ASUS Update Vx.xx (optional): Installs a program to help you update
your BIOS or download a BIOS image file.
Install PC-cillin 98 Vx.xx (optional): Installs the PC-cillin virus protection
software. View the online help for more information.
Install Adobe Acrobat Reader Vx.x (optional): Installs the Adobe Acrobat
Reader software necessary to view user’s manuals saved in PDF format. Up-
dated or other language versions of this motherboard's manual is available in
PDF format at any of our web sites.
•
Show Motherboard Information: Allows you to view information about your
motherboard, such as product name, BIOS version, and CPU.
Browse Support CD: Allows you to view the contents of the CD.
ReadMe: Allows you to view the support CD file list and contact information.
•
•
(TO SEE THE FOLLOWING ITEM(S), CLICK RIGHT ARROW ON THE
LOWER-RIGHT CORNER OF THE MAIN MENU)
•
Exit: Exits the CD installation menu.
(TO RETURN TO THE MAIN MENU, CLICK LEFTARROW ON THE LOWER-
RIGHT CORNER OF THE SECONDARY MENU)
Additonal CD Content: Flash BIOS writer in the FLASH folder.
ASUS CUBX-L/CUBX-E User’s Manual
77
5. SOFTWARE SETUP
(This page was intentionally left blank.)
78
ASUS CUBX-L/CUBX-E User’s Manual
6. SOFTWARE REFERENCE
6.1 ASUS PC Probe
ASUS PC Probe is a convenient utility to continuously monitor your com-
puter system’s vital components, such as fan rotations, voltages, and tem-
peratures. It also has a utility that lets you review useful information about
your computer, such as hard disk space, memory usage, and CPU type, CPU
speed, and internal/external frequencies through the DMI Explorer.
6.1.1 Starting ASUS PC Probe
WhenASUS PC Probe starts, a splash screen appears allowing you to select
whether to show the screen again when you open PC Probe or not. To by-
pass this startup screen, clear the Show up in next execution check box.
To open ASUS PC Probe, click the Windows Start button, point to Pro-
grams, and then ASUS Utility, and then click Probe Vx.xx.
The PC Probe icon
will appear on the taskbar’s system tray indicating
that ASUS PC Probe is running. Clicking the icon will allow you to see the
status of your PC.
ASUS CUBX-L/CUBX-E User’s Manual
79
6. SOFTWARE REFERENCE
6.1.2 Using ASUS PC Probe
Monitoring
Monitor Summary
Shows a summary of the items being
monitored.
Temperature Monitor
Shows the PC’s temperature (for
supported processors only).
Temperature Warning
threshold adjustment
(Move the slider up to increase the
threshold level or down to decrease
the threshold level)
Fan Monitor
Shows the PC’s fan rotation.
Fan Warning
threshold adjustment
(Move the slider up to increase the
threshold level or down to decrease
the threshold level)
Voltage Monitor
Shows the PC’s voltages.
80
ASUS CUBX-L/CUBX-E User’s Manual
6. SOFTWARE REFERENCE
Settings
Lets you set threshold levels and poll-
ing intervals or refresh times of the PC’s
temperature, fan rotation, and voltages.
CPU Cooling System Setup
Lets you select when to enable
software CPU cooling. When
When CPU Overheated is
selected, the CPU cooling
system is enabled whenever the
CPU temperature reaches the
threshold value.
History
Lets you record the monitoring activ-
ity of a certain component of your PC
for future reference.
Fan Control
Lets you enable/disable Smart Fan Con-
trol. Smart Fan Control adjusts the fan
speed automatically based on the current
CPU temperature and predefined thresh-
old.
Information
Hard Drives
Shows the used and free space of the
PC’s hard disk drives and the file allo-
cation table or file system used.
ASUS CUBX-L/CUBX-E User’s Manual
81
6. SOFTWARE REFERENCE
Memory
Shows the PC’s memory load, memory
usage, and paging file usage.
Device Summary
Shows a summary of devices in your PC.
DMI Explorer
Shows information pertinent to the PC,
such as CPU type, CPU speed, and in-
ternal/external frequencies, and memory
size.
Utility
Lets you run programs outside of the
ASUS Probe modules. To run a program,
click Execute Program. NOTE: This
feature is currently unavailable.
82
ASUS CUBX-L/CUBX-E User’s Manual
6. SOFTWARE REFERENCE
6.1.3 ASUS PC Probe Task Bar Icon
Right clicking the PC Probe
icon will bring up a menu to
open or exit ASUS PC Probe
and pause or resume all sys-
tem monitoring.
When the ASUS PC Probe
senses a problem with your
PC, portions of the ASUS PC
Probe icon changes to red, the
PC speaker beeps, and the
ASUS PC Probe monitor is dis-
played.
ASUS CUBX-L/CUBX-E User’s Manual
83
6. SOFTWARE REFERENCE
6.2 ASUS Update
ASUS LiveUpdate is a utility that allows you to update your motherboard’s
BIOS and drivers. The use of this utility requires that you are properly con-
nected to the Internet through an Internet Service Provider (ISP).
1. Start ASUS Update
Launch the utility from Start | Programs | ASUS
Utility | ASUS Update Vx.xx.
2. Select an update method.
3. If you selected updating/downloading from the
Internet, you will need to select an Internet site.
Choose the site that is closest to you or click
Auto Select.
If you selected Update from a file, you will
be prompted to locate the file.
84
ASUS CUBX-L/CUBX-E User’s Manual
7. APPENDIX
7.1 PCI-L101 Fast Ethernet Card
LAN Activity
Output Signal
Intel
Chipset
RJ45
ASUS
Wake on LAN
Output Signal
Motherboard type
Other
If you are using theASUS PCI-L101 on an ASUS motherboard, leave the jumper on
its defaut setting of “ASUS.” If you are using another brand of motherboard, set the
jumper to “Other.” Connect the Wake on LAN (WOL) output signal to the
motherboard’s WOL_CON in order to utilize the wake on LAN feature of the moth-
erboard. Connect the LAN activity output signal (LAN_LED) to the system cabinet’s
front panel LAN_LED in order to display the LAN data activity.
ASUS CUBX-L/CUBX-E User’s Manual
85
7. APPENDIX
7.1.1 Features
•
•
•
•
•
•
•
•
•
Intel 82558 Ethernet LAN Controller (Fully integrated 10BASE-T/100BASE-TX)
Wake-On-LAN Remote Control Function Supported
PCI Bus Master Complies to PCI Local Bus Rev. 2.1 specifications
Consists of MAC & PHY (10/100Mbps) interfaces
Complies to IEEE 802.3 10BASE-T and IEEE 802.3u 100BASE-TX interfaces
Fully supports 10BASE-T & 100BASE-TX operations through a single RJ45 port
Supports 32-bit Bus Master Technology / PCI Rev. 2.1
Enhancements on ACPI & APM
Adheres to PCI Bus Power Management Interface Rev. 1.0, ACPI Rev. 1.0, and
Device Class Power Management Rev. 1.0
•
IEEE 802.3u auto-negotiation for 10Mbps/100Mbps Network Data Transfer
Rates.
•
•
Provides LED indicators for monitoring network conditions
Plug and Play
7.1.2 Software Driver Support
•
•
NetWare ODI Drivers - Novell Netware 3.x, 4.x, DOS, OS/2 Client
NDIS 2.01 Drivers - Microsoft LAN Manager, Microsoft Windows 3.11, IBM
LAN Server
•
NDIS 3.0 Drivers - Microsoft Windows NT, Microsoft Windows 95, Microsoft
Windows 3.11
7.1.3 Question and Answer
Q: What is Wake-On-LAN ?
A: The Wake-On-LAN feature provides the capability to remotely power on sys-
tems supporting Wake-On-LAN by simply sending a wake-up frame. With this
feature, remotely uploading/downloading data to/from systems during off-peak
hours will be feasible.
Q: What can Wake-On-LAN do for you ?
A: Wake-On-LAN is a remote management tool with advantages that can reduce
system management workload, provide flexibility to the system administrator’s
job, and then of course save you time-consuming efforts and costs.
Q: What components does Wake-On-LAN require to be enable?
A: To enable Wake-On-LAN function, your system requires Ethernet LAN adapter
card that can activate Wake-On-LAN function, a client with Wake-On-LAN capa-
bility, and software such as LDCM Rev. 3.10 or up that can trigger wake-up frame.
86
ASUS CUBX-L/CUBX-E User’s Manual
7. APPENDIX
7.2 ASUS CIDB Intrusion Detection Module
The optional ASUS CIDB is a module for providing audible intrusion alarm and
logging for ASUS motherboards equipped with the chassis connector. The module
detects a chassis intrusion by either light striking its photo sensor or by the closing
or opening of a chassis-mounted momentary toggle switch. An intrusion memory
function allows detection and clearing the intrusion notification by the BIOS pro-
gram on the next bootup.
Connectors to detect intrusion by chassis
mounted micro switches
Buzzer to sound the alarm
Battery for the memory
Photo sensor sensitivity adjustment
Chassis
Photo sensor to detect intrusion by light
connector
extension
cable
Pass-through for another SMBus device
Intrusion memory
Connector to dock with the
motherboard’s chassis connector
Connector to dock with the motherboard’s
SMBus connector
SMB cable
7.2.1 Using the ASUS CIDB
1. You must have an ASUS motherboard with: (1) a chassis connector and (2) a
System Management Bus (SMB) connector.
2. Connect the CIDB directly to the chassis connector or use the provided exten-
sion cable and mount the CIDB to the chassis using a double-sided foam adhe-
sive tape or with screws and spacer posts.
CAUTION! The CIDB’s component pins and metallic points must not come in
contact with another metallic surface or else shorting will occur!
3. Use the SMBIN connector and the provided SMB cable to connect the CIDB to
the SMB connector on the motherboard. If another SMB device is already used
on the motherboard, you may unplug it and connect it to the SMBOUT connec-
tor on the CIDB.
4. Check the hardware settings:
•
•
PHOTO jumper should be enabled to use the photo sensor.
MS1 and/or MS2 connectors should be connected to momentary toggle
switches mounted on the chassis to use the switch close or switch open
method for triggering an intrusion event.
ASUS CUBX-L/CUBX-E User’s Manual
87
7. APPENDIX
5. To stop the alarm from sounding, use the BIOS setup or momentarily place a
jumper on (or short manually) the CLR jumper. Note that the jumper must be
removed for the CIDB to work normally again.
6. If you have an updated BIOS with intrusion support, booting the computer after
an intrusion may require a password if configured through BIOS.
7.2.2 Setting up the ASUS CIDB
MS1 MS1/MS2:
Micro Switches from the chassis
panels can be connected here
to trigger chassis intrusion.
MS2
(Only one pair--MS1 or MS2--should
be used for switch open detection.)
SWITCH SWITCH
SWITCH Close:
1
Intrusion event triggered
if either MS1 or MS2 is closed
SWITCH Open:
1
MS1
MS2
Close Open
Intrusion event triggered
if MS1 and MS2 are opened
SWITCH
Buzzer
(sensitive)
5
VR:
VR
4
Sensitivity adjustment for
the photo sensor.
(5) is the most sensitive.
(0) is the least sensitive.
CR2032 3V
Lithium Cell
3
2
OR
1
0
best
range
(not sensitive)
PHOTO
PHOTO
1
PHOTO
1
PHOTO:
Enable/Disable
the Photo Sensor
CLR
Enable Disable
SMBCLK
1
SMBOUT:
Connects to another
SMB device (if used)
SMBIN
Ground
SMBDATA
+5V
CLR
CLR
SMBOUT
SMBIN
1
SMBIN:
Connects to the motherboard’s
SMB connector through an SMB cable
Clear
Normal
Clear:
Stops the alarm
from sounding
7.2.3 ASUS CIDB Additional Considerations
1. If there is no power to the motherboard (i.e. removing the power cord or turning
the power supply’s switch off), the alarm will not sound but the CIDB will still
memorize an intrusion event which BIOS will detect on the next bootup.
2. Any chassis intrusion detection components on the motherboard will not work if
the CIDB is used.
3. The P2B-LS motherboard must use an external battery pack on the EXTBATT
connector or else neither the alarm or intrusion memory functions will work.
88
ASUS CUBX-L/CUBX-E User’s Manual
7. APPENDIX
7.3 Glossary
1394
1394 is the IEEE designation for the high performance serial bus at 12.5, 25 or
50MBytes/sec speeds. This serial bus defines both a back plane physical layer and a
point-to-point cable-connected virtual bus. The primary application of the cable ver-
sion is the integration of I/O connectivity at the back panel of personal computers
using a low-cost, scalable, high-speed serial interface. The 1394 standard also pro-
vides new services such as live connect/disconnect capability for external devices
including disk drives, printers and hand-held peripherals such as scanners and cam-
eras. This is a new standard to complement the slower USB interface and to compete
with the more expensive SCSI interface.
AC97 (Audio Codec '97)
AC '97 is the next step in enabling PCs with audio quality comparable to consumer
electronics devices. The specification defines new cost-effective options to help in-
tegrate the components necessary to support next-generation auto-intensive PC ap-
plications such as DVD, 3-D multiplayer gaming and interactive music. The speci-
fication also defines new extensions supporting modem and docking to help both
desktop and mobile manufacturers adopt these new technologies more quickly and
cost-effectively. This specification uses software emulation to compete with the PCI
SoundBlaster specification.
ACPI (Advanced Configuration and Power Interface)
TheACPI specification defines a cross-platform interface designed to support many
operating systems. ACPI defines a flexible and abstract hardware interface that pro-
vides a standard way to integrate power management features throughout a PC sys-
tem, including hardware, operating system and application software. This enables
the system to automatically turn ON and OFF peripherals such as CD-ROMs, net-
work cards, hard disk drives, and printers, as well as consumer devices connected to
the PC such as VCRs, TVs, phones, and stereos. With this technology, peripherals
will also be able to activate the PC. For example, inserting a tape into a VCR can
turn on the PC, which could then activate a large-screen TV and high-fidelity sound
system.
AGP (Accelerated Graphics Port)
An interface specification that enables high-performance 3D graphics on mainstream
PCs. AGP was designed to offer the necessary bandwidth and latency to perform
texture mapping directly from system memory.
Bus
Bus Frequency
Bandwidth
Data Transfer Rate
PCI
AGP 1X
AGP 2X
33MHz
66MHz
66MHz
33MHz
66MHz
133MHz
133MByte/sec
266MByte/sec
512MByte/sec
AGP 4X
66MHz
266MHz
1024MByte/sec
BIOS (Basic Input/Output System)
BIOS is a set of routines that affect how the computer transfers data between com-
puter components, such as memory, disks, and the display adapter. The BIOS in-
structions are built into the computer’s read-only memory. BIOS parameters can be
configured by the user through the BIOS Setup program. The BIOS can be updated
using the provided utility to copy a new BIOS file into the EEPROM.
Bit (Binary Digit)
Represents the smallest unit of data used by the computer. A bit can have one of two
values: 0 or 1.
ASUS CUBX-L/CUBX-E User’s Manual
89
7. APPENDIX
Boot
Boot means to start the computer operating system by loading it into system memory.
When the manual instructs you to “boot” your system (or computer), it means to
turn ON your computer. “Reboot” means to restart your computer. When using Win-
dows 95 or later, selecting “Restart” from “Start | Shut Down...” will reboot your
computer.
Bus Master IDE
PIO (Programmable I/O) IDE requires that the CPU be involved in IDE access and
waiting for mechanical events. Bus master IDE transfers data to/from the memory
without interrupting the CPU. Bus master IDE driver and bus master IDE hard disk
drives are required to support bus master IDE mode.
Byte (Binary Term)
One byte is a group of eight contiguous bits. A byte is used to represent a single
alphanumeric character, punctuation mark, or other symbol.
COM Port
COM is a logical device name used by to designate the computer serial ports. Point-
ing devices, modems, and infrared modules can be connected to COM ports. Each
COM port is configured to use a different IRQ and address assignment.
Concurrent PCI
Concurrent PCI maximizes system performance with simultaneous CPU, PCI and
ISA bus activities. It includes multi-transaction timing, enhanced write performance,
a passive release mechanism and support for PCI 2.1 compliant delayed transac-
tions. Concurrent PCI provides increased bandwidth, reduced system latencies, im-
proves video and audio performance, and improves processing of host based appli-
cations.
CPU (Central Processing Unit)
The CPU, sometimes called “Processor,” actually functions as the “brain” of the
computer. It interprets and executes program commands and processes data stored
in memory. Currently, there are socket 370 (for Pentium III FC-PGA and Celeron-
PPGA), socket 7 (for Pentium, AMD, Cyrix, IBM), slot 1 (for Pentium II and III),
slot 2 (for Xeon), and slot A (for AMD) processors.
Device Driver
A device driver is a special set of instructions that allows the computer’s operating
system to communicate with devices such as VGA, audio, printer, or modem.
DOS (Disk Operating System)
DOS is the foundation on which all other programs and software applications oper-
ate, including Windows. DOS is responsible for allocating system resources such as
memory, CPU time, disk space, and access to peripheral devices. For this reason,
DOS constitutes the basic interface between you and your computer.
DRAM (Dynamic Random Access Memory)
There are several different types of DRAM such as, EDO DRAM (Extended Data
Output DRAM), SDRAM (Synchronous DRAM), and RDRAM (Rambus DRAM).
Flash ROM
The flash ROM is designed to be a resident program and can be updated by a spe-
cific programming method. Normally, the flash ROM is used for system BIOS which
initiates hardware devices and sets up necessary parameters for the OS. Since the
contents of flash ROM can be modified, users are able to update the BIOS by them-
selves.
IDE (Integrated Drive Electronics)
IDE devices integrate the drive control circuitry directly on the drive itself, elimi-
nating the need for a separate adapter card (in the case for SCSI devices). UltraDMA/
100 IDE devices can achieve up to 100MB/Sec transfer.
90
ASUS CUBX-L/CUBX-E User’s Manual
7. APPENDIX
LPT Port (Line Printer Port)
Logical device name reserved by DOS for the computer parallel ports. Each LPT
port is configured to use a different IRQ and address assignment.
MMX
A set of 57 new instructions based on a technique called Single Instruction, Multiple
Data (SIMD), which is built into the new Intel Pentium PP/MT (P55C) and Pentium
II (Klamath) CPU as well as other x86-compatible microprocessors. The MMX in-
structions are designed to accelerate multimedia and communications applications,
such as 3D video, 3D sound, video conference.
OnNow
The OnNow design initiative is a comprehensive, system-wide approach to system
and device power control. OnNow is a term for PC that is always ON but appears
OFF and responds immediately to user or other requests. The OnNow design initia-
tive involves changes that will occur in the Microsoft Windows operating system,
device drivers, hardware, and applications, and also relies on the changes defined in
the Advanced Configuration and Power Interface (ACPI) specification.
PC100
SDRAM is Intel's goal is to ensure that memory subsystems continue to support
evolving platform requirements and to assure that memory does not become a bottle-
neck to system performance. It is especially important to ensure that the PC memory
roadmap evolves together with the performance roadmaps for the processors, I/O
and graphics.
PCI Bus (Peripheral Component Interconnect Local Bus)
PCI bus is a specification that defines a 32-bit data bus interface. PCI is a standard
widely used by expansion card manufacturers.
PCI Bus Master
The PCI Bus Master can perform data transfer without local CPU help and further-
more, the CPU can be treated as one of the Bus Masters. PCI 2.1 supports concur-
rent PCI operation to allow the local CPU and bus master to work simultaneously.
Plug and Play BIOS
The ISA bus architecture requires the allocation of memory and I/O address, DMA
channels and interrupt levels among multiple ISA cards. However, configuration of
ISA cards is typically done with jumpers that change the decode maps for memory
and I/O space and steer the DMA and interrupt signals to different pins on the bus.
Further, system configuration files may need to be updated to reflect these changes.
Users typically resolve sharing conflicts by referring to documentation provided by
each manufacturer. For the average user, this configuration process can be unreli-
able and frustrating. Plug and play (PnP) BIOS eliminates the ISA add-on card hard-
ware conflict problem. The PnP BIOS uses a memory block to define and remember
each card's configuration, which allows the user to change the card's IRQs and DMA
in BIOS either automatically or manually.
POST (Power On Self Test)
When you turn ON the computer, it will first run through the POST, a series of
software-controlled diagnostic tests. The POST checks system memory, the mother-
board circuitry, the display, the keyboard, the diskette drive, and other I/O devices.
PS/2 Port
PS/2 ports are based on IBM Micro Channel Architecture. This type of architecture
transfers data through a 16-bit or 32-bit bus. A PS/2 mouse and/or keyboard may be
used on ATX motherboards.
RDRAM (Rambus DRAM)
Developed by Rambus, Inc., this type of memory can deliver up to 1.6GB of data
per second. RDRAM is the first interface standard that can be directly implemented
on high performance VLSI components such as, CMOS DRAMs, memory control-
lers, and graphics/video ICs.
ASUS CUBX-L/CUBX-E User’s Manual
91
7. APPENDIX
ROM (Read Only Memory)
ROM is nonvolatile memory used to store permanent programs (called firmware)
used in certain computer components. Flash ROM (or EEPROM) can be repro-
grammed with new programs (or BIOS).
SCSI (Small Computer System Interface)
High speed multi-threaded I/O interface defined by the X3T9.2 committee of the
American National Standards Institute (ANSI) for connecting many peripheral de-
vices. The standard started from 10MBytes/sec to 160MBytes/sec available today.
SDRAM (Synchronous DRAM)
The SDRAM features a fully synchronous operation referenced to a positive edge
clock whereby all operations are synchronized at a clock input which enables the
coexistence of high performance and a simple user interface. SDRAM takes memory
access away from the CPU's control; internal registers in the chips accept the re-
quest, and let the CPU do something else while the data requested is assembled for
the next time the CPU talks to the memory. As they work on their own clock cycle,
the rest of the system can be clocked faster. There is a version optimized for video
cards, and main memory for motherboards.
SPD for SDRAM module
Serial Presence Detect (SPD) is most like an ID detect for SDRAM module, it using
a EEPROM component on DIMM module for storing module configuration infor-
mation inside. The Serial Presence Detect function is implemented using a 2048 bit
EEPROM component. This nonvolatile storage device contains data programmed
by the DIMM manufacturer that identifies the module type and various SDRAM
organization and timing parameters.
SSE (Streaming SIMD Extensions)
A set of new instructions added to existing architectures that enables a better visual
experience with an accelerated 3D geometry pipeline and support for new applica-
tions, such as real-time video encoding and speech recognition.
System Disk
A system disk contains the core file of an operating system and is used to boot up the
operating system.
UltraDMA
Ultra DMA/33 is a "synchronous DMA" protocol designed by Intel. This function is
included into Intel's PIIX4 chipset. The traditional IDE transfer only uses one edge
of the data stroke as the data transfer. Ultra DMA/33 uses both edges of data strobe
when the data is transferred. Hence, the data transfer rate is double of the PIO mode
4 or DMA mode 2 (16.6MB/s x2 = 33MB/s) on ATA-2 devices.
Ultra ATA/66, also known as Ultra DMA/66, is an extension of current Ultra ATA/
33 interface. This new high-speed interface has doubled the Ultra ATA/33 burst data
transfer rate to 66.6 Mbytes/sec and maximized disk performance under current PCI
local bus environment
USB (Universal Serial Bus)
A 4-pin serial cable bus that allows up to 127 plug and play computer peripherals
such as keyboard, mouse, joystick, scanner, printer, modem, and monitor to share a
bandwidth through a host scheduled token based protocol. This allows attaching or
detaching while the host and other peripherals are in operation. Supports synchro-
nous and asynchronous transfer types over the same set of wires up to 12Mbit/sec.
USB 2.0 provides twice the transfer rate compared to USB 1.0 and competes with
the 1394 standard.
Wake-On-LAN
Computer will automatically wake-up upon receiving a wake-up packet through a
Network interface when it is under power soft-off, suspend or sleep mode.
92
ASUS CUBX-L/CUBX-E User’s Manual
INDEX
Serial Port 31
Symbols
SMBus 36, 37
Thermal Sensor 38
USB 31
16-bit I/O Recovery Time 59
8-bit I/O Recovery Time 59
Wake-On-LAN 34
Wake-On-Ring 34
CPU Bus/PCI Freq. (MHz) 54
CPU Core:Bus Freq. Multiple 54
CPU Fan Speed 70
CPU Level 1 Cache 55
CPU Level 2 Cache 55
CPU Level 2 Cache ECC Check 55
CPU Reinstallation 56
CPU Speed 54
A
AC PWR Loss Restart 68
Accelerated Graphics Port 29
AGP 29
ASUS PC Probe
Using 79
ASUS Update
Using 84
ATAPI CD-ROM 71
ATX Power Supply Connector 38
Automatic Power Up 69
CPU Temperature 70
CPU Upgrade 56
CPU Vcore 55
Cylinders 50
B
D
Beep Codes 41
BIOS
Discard Changes 74
DMA x Used By ISA 64
DRAM Idle Timer 59
Beep Codes 41
Managing 42
Updating 42
BIOS Beep Codes 41
E
BIOS Update 55
Boot Sequence 71
ECP DMA Select 61
Exit Discarding Changes 73
Exit Saving Changes 73
Expansion Cards
Boot Up Floppy Seek 72
Boot Up NumLock Status 52
Boot Virus Detection 72
AGP Pro 29
Assigning IRQs 27
C
C8000-DFFFF Shadow 65
Central Processing Unit 25
Chassis Fan Speed 70
Chassis Intrusion Lead 32
Chip Configuration 58
CHS Capacity 51
F
Floppy 3 Mode Support 48
Floppy Disk Access Control 60
Floppy Disk Drive Connector 32
Full Screen Logo 72
Connectors
G
ATX Power Supply 38
Floppy Disk Drive 32
IDE 33
Keyboard 30
Parallel Port 31
Graphics Aperture Size 59
H
Power Supply Thermal Sensor 38
PS/2 Keyboard 30
PS/2 Mouse 30
Halt On 53
ASUS CUBX-L/CUBX-E User’s Manual
93
INDEX
Hardware Monitor 70
Hardware Setup
Maximum LBA Capacity 51
MB Temperature 70
CPU Installation 25
Memory Installation 23
HDD Power Down 67
Head 51
Memory Hole At 15M-16M 59
Memory Installation 23
Mouse Connector 30
Multi-Sector Transfers 51
Headers
USB 37
Host Bus Fast Data Ready 59
O
Onboard FDC Swap A & B 60
Onboard Parallel Port 61
Onboard PCI IDE Enable 59
Onboard Serial Port 1 60
Onboard Serial Port 2 60
OS/2 Onboard Memory > 64M 55
Other Boot Device Select 72
I
IDE Activity LED Lead 35
IDE Connectors 33
IDE Hard Drive 71
Installation
CPU 25
Installed Memory 53
Interrupts
P
Parallel Port Connector 31
Parallel Port Mode 61
PCI 2.1 Support 59
PCI Configuration 62
PCI Latency Timer 62
PCI/VGA Palette Snoop 62
PIO Mode 51
Plug & Play O/S 72
Power Fan Speed 70
Power Management 66
Power Up Control 68
Procedure
Request Table 27
Standard Assignments 27
IRQ XX Used By ISA 63
ISA MEM Block BASE 65
K
Keyboard Auto-Repeat Delay 52
Keyboard Auto-Repeat Rate 52
Keyboard Connector 30
Keyboard Lock Switch Lead 38
L
CPU Installation 25
Language 53
Leads
Processor Serial Number 55
PS/2 Keyboard Connector 30
PS/2 Mouse Connector 30
PS/2 Mouse Function Control 55
PWR Button < 4 Secs 67
PWR Up On Modem Act 68
PWR Up On PS2 KB/Mouse 69
Chassis Intrusion 32
IDE Activity LED 35
Keyboard Lock Switch 38
Reset Switch 38
System Message LED 38
System Power LED 38
Legacy Diskette A 48
Q
Load Setup Defaults 74
Quick Power On Self Test 72
M
R
Managing BIOS 42
Removable Device 71
Reset Configuration Data 72
94
ASUS CUBX-L/CUBX-E User’s Manual
INDEX
Reset Switch Lead 38
Using
ASUS PC Probe 79
ASUS Update 84
S
Save Changes 74
V
SDRAM CAS Latency 58
SDRAM Configuration 58
SDRAM RAS Precharge Time 58
SDRAM RAS to CAS Delay 58
Sector 51
Serial Port Connectors 31
Shadow Configuration 65
Slot 1 IRQ 62
VGA BIOS Sequence 63
Video Memory Cache Mode 59
Video Off Method 67
Video Off Option 67
Video ROM BIOS Shadow 65
W
Slot 2 IRQ 62
Slot 3/6 IRQ 62
Slot 4/5 IRQ 62
SMART Monitoring 51
SMBus Connector 36, 37
Snoop Ahead 59
Wake On LAN 68
Wake Up By Keyboard 69
Wake-On-LAN Connector 34
Wake-On-Ring Connector 34
Starting Up 41
Supervisor Password 53
Suspend Mode 67
Suspend-to-RAM Capability 67
SYMBIOS SCSI BIOS 62
System Date 48
System Hangup 57
System Message LED Lead 38
System Power LED Lead 38
System Time 48
T
Thermal Sensor Connector 38
Translation Method 50
Type 49
U
UART2 Use Infrared 60
ULTRA DMA Mode 51
Updating BIOS 42
USB Headers 37
USB IRQ 63
USB Legacy Support 55
USB Ports 31
User Password 53
ASUS CUBX-L/CUBX-E User’s Manual
95
INDEX
(This page was intentionally left blank.)
96
ASUS CUBX-L/CUBX-E User’s Manual
®
Goes Mobile!
L8400 Series
Compact Professional Notebook PC
• 14.1” TFT Color Display
• 450MHz to 700MHz+
• 64MB to 192MB Memory
• 2X AGP 3D w/8MB VRAM
• 100MHz Processor Side Bus
M8300/8200 Series
Thin & Light Convertible Notebook PC
• 13.3” or 12.1” TFT Color Display
• 366MHz to 650MHz+
• 64MB to 192MB Memory
• Supports Two Hard Drives
L7300/7200 Series
All-in-One Compact Notebook PC
• 13.3” or 12.1” TFT Color Display
• 366MHz to 650MHz+
• 64MB to 192MB Memory
Visit www.asus.com for updated specifications
®
Barebone Servers
Pentium® III PC100 ECC Ultra2 SCSI
5.25”
Pentium® II Max. Memory
Onboard Fixed Storage
Hot-Swap Trays
Support
(GB)
(Channels)
Devices
AP100
1
1
1
1
1
2
1
1
2
1
1
1
1
2
1
1
2
3
3
4
4
4
4
4
4
0
AP200
2
0
AP2000
AP2500
AP3000
AP6000
AP7500
AP8000
2
3 or 5*
3 or 5*
3 or 5*
8**
2
2 Xeon™
2
2
8**
2 Xeon™
8**
*
Three 1.6-inch or five 1-inch SCA-2 SCSI hard drives
** Eight 1.6-inch or 1-inch SCSI hard drives
Mid-Range Servers
AP6000
AP7500
AP8000
Value Servers
AP2000
AP2500
AP3000
Group Servers
AP100
AP200
Rack Mountable
Visit www.asus.com for updated specifications
ASUS AR1000 RAID Sub-system
with DA3000 SCSI-to-SCSI RAID Controller
•
Supports 5x86 RAID processor and two 72-pin SIMM sockets for up to 128MB
cache memory
•
•
•
•
•
•
•
•
•
•
•
•
Supports three Ultra2 SCSI channels; up to 80MB/sec data transfer rate
Supports multiple Host/Drive channel capacity
Redundant controller capacity
Supports non-RAID, RAID levels 0, 1, 0+1, 3, 5
On-line failure drive rebuilding
Automatic rebuilding — supports local/global spare drive
On-line expansion capacity
Supports SAF-TE (SCSI Accessed Fault-Tolerant Enclosure) feature
Provides LCD panel and RS-232 port to configure RAID
Ten 1.0” or six 1.6” Ultra2 SCSI SCA-2 hot-swappable drive bays
19” rack mountable (height: 5U)
LED for hard disk power and
working status
•
•
•
Two 8cm system fans and four 6cm
drive fans
Aluminum disk arrays for easy
heat dissipation
350W redundant power supply
ASUS PCI-DA2100/2200 Series SCSI RAID Card
•
•
•
•
•
•
•
•
•
PCI-DA2100 series support 4x86 DX4-100 processor
PCI-DA2200 series support 5x86-133 processor
One 72-pin SIMM socket supports up to 128MB cache memory
RAID levels 0, 0+1, 3, 5, non-RAID
PCI-DA2100A supports Ultra Wide SCSI interface and dual channels
PCI-DA2200A supports Ultra2 SCSI interface and single channel
PCI-DA2200B supports Ultra2 SCSI interface and dual channels
Automatic bad sector reassignment
Supports both global and lo-
cal spare drive operation
•
•
•
Background rebuilding
PCI rev. 2.1 compliant
Up to 8 logical drives and 8
partitions per logical drive;
number of drives for each
logical drive has no limitation
Visit www.asus.com for updated specifications
®
8x DVD-ROM Drive
• Industry-leading performance for even the most
demanding applications
• Maximum transfer rate: 8X DVD-ROM / 40X
CD-ROM
• High speed digital audio extraction
• Supports UltraDMA/33 transfer mode
• Complies with MPC3 standard
• Supports Multi-Read function
®
Ultra-Fast CD-ROM
• Supports high speed CD-Audio playback
• Supports high speed digital audio extraction
• Supports UltraDMA/33 transfer mode
• Compatible with all CD formats
• Supports multi-read function (CD-R/CD-RW)
Visit www.asus.com for updated specifications
 |