Apple Computer Monitor User Manual

Unpacking and wall mounting instructions  
For the unpacking instructions follow the illustrated steps 1 to 5 printed  
on the packaging (outside and inside).  
For the wall mounting instructions follow the illustrated steps 6 to 8  
printed on the first pages of this instruction booklet.  
Make sure that the wall mount is being fixed securely enough so that it meets  
safety standards.The weight of the monitor (excl. packaging) is about 43 kg.  
Connect your computer  
& Connect one end of theVGA cable 1 supplied to the video card of the  
computer and the other end to the VGA IN connector at the rear side of the  
monitor. Fix the connectors firmly with the screws on the plug.  
é In case of a Multimedia computer, connect the audio cable 2 to the audio  
outputs of your Multimedia computer and to the AUDIO IN R (right) and L  
(left) inputs of the monitor.  
MAINS INLET  
L
AUDIO IN  
AUDIO OUT  
VGA IN  
VGA OUT  
R
5
Connect one end of anotherVGA cable 3 to the VGA OUT connector at  
the rear side of the monitor and the other end to the VGA IN connector of a  
secondVGA monitor.  
1
2
4
3
Daisy chaining  
The Active Loop Through facility makes it possible to make a daisy chain with  
a secondVGA monitor.  
In case of a Multimedia computer, also connect the audio cables 4 to the  
AUDIO L and R outputs of the monitor and to the AUDIO IN L and R inputs  
of the secondVGA monitor.  
Note: only use the VGA cables supplied or use cables that are specially delivered  
with the monitor.  
Connect your Apple Macintosh* computer  
Attention: Macintosh computers with separate H and V synchronisation signals  
can be used together with the supplied adaptor. Macintosh computers with  
Composite Sync and Sync on Green signals may need a special (not  
supplied) adaptor or cable. Contact your dealer.  
Connect the supplied switchable adaptor for Apple video connectors to one  
end of aVGA cable.  
Put the DIP switches on the adaptor in the following positions :  
1
off  
2
off  
3
on  
4
on  
Connect the end of theVGA cable with the adaptor to the video card of the  
computer and the other end to the VGA IN connector on the back of the  
monitor.  
Screw the connectors down firmly.  
15-pin D sub  
(2-row)  
15-pin mini D sub  
(3-row)  
*
Apple Macintosh is a registered trademark of Apple Computer, Inc.  
1
Use of the remote control  
B no function  
VGA no function  
FRONT no function  
B
π
VGA  
FRONT  
AV1  
OK  
OK to activate your choice  
AV1, AV2, AV3,AV4 no function  
o
MENU  
œ
MENU to switch the VGA menu on/off  
cursor keys to select your choice and to  
alter a selected adjustment  
p
AV2  
Picture format  
In VGA mode, press the p or π keys to  
switch between a 4:3 or a 16:9 picture  
format.  
AV3  
¬
AV4  
PICTURE SOUND  
SMART  
CONTROLS  
¬
Mute key  
- CH/P + no function  
-
CH/P  
+
-
V
+
temporarily mute the sound or restore it  
V press - or + to adjust the volume  
SMART CONTROLS  
PICTURE/SOUND no function  
VGA menu  
& Press the MENU key to switch on the VGA menu.  
é Select one of the symbols with the o and œ keys:  
H for contrast  
G for brightness,  
for colour temperature  
for horizontal picture position  
for vertical picture position  
V
for volume  
Press the p and π keys to alter the selected adjustment.  
Press the MENU key again to switch off the VGA menu.  
3
Tips  
Ambient temperature  
higher altitude, the picture becomes  
unstable and the picture performance is  
deteriorating. Bringing the set below 2000  
m it works fine again.Transportation has  
no influence.  
Transport  
Do not hang up the monitor above a  
central heating or other heating sources.  
Keep the original packaging to transport the  
monitor if needed.  
Active LoopThrough  
End of life directives  
The Active LoopThrough facility makes it  
possible to make a daisy chain forVGA.  
Maximum 2 sets.  
Philips is paying a lot of attention to  
produce environmentally-friendly in green  
focal areas.Your new monitor contains  
materials which can be recycled and  
reused.  
At the end of its life specialised companies  
can dismantle the discarded monitor to  
concentrate the reusable materials and to  
minimise the amount of materials to be  
disposed of.  
Control of peripheral equipment  
The infrared signals of the screen may  
influence the reception sensitivity of other  
peripherals. Solution: replace the batteries  
of the remote control or change position  
of other equipment. E.g. keep away a  
wireless headphone from within a radius  
of 1.5 m.  
Care of the screen  
Clean the anti-reflex coated flat glass  
screen with a slightly damp soft cloth. Do  
not use abrasives solvents as it can  
damage the glass surface of the screen.  
No stable or not synchronisedVGA  
picture  
Check if you have selected the correct  
VGA mode in your PC (640x480,  
640x400, 640x350, MAC II, SVGA, XGA).  
Plasma Display characteristics  
Please ensure you dispose of your old  
monitor according to local regulations.  
When switching over to another picture  
after having displayed the same still picture  
for a long time (many hours), it may  
happen that some parts from the previous  
picture will remain on screen due to a  
kind of memory effect.This ghost picture  
will disappear after some time.To avoid  
this effect change the pictures regularly or  
for PC use you can turn on a screen saver  
in your computer.  
Philips has built in an automatic shift of  
the picture every 5 minutes to avoid this  
effect and to prolong the life of the  
screen.  
Very incidentally and after a longer period  
of unuse (approx. 1 year) the screen may  
display some strange colour deficiencies.  
This is quite normal for plasma displays  
and these effects will disappear after the  
set has been turned on for some time.  
A plasma display consists of more than 1,2  
Million colour pixels. It is within industry  
standards that very few pixels (< 0.001%)  
may be defective, even for a new set.  
There is however no reason to doubt  
about the quality of the set.  
How to dispose of batteries ?  
The batteries supplied do not contain the  
heavy metals mercury and cadmium.  
Nevertheless in many countries batteries  
may not be disposed of with your  
household waste. Please ensure you dispose  
of batteries according to local regulations.  
No picture or no sound  
Are the supplied cables connected  
properly? (The power cable to the display,  
theVGA cables, the audio cables,...)  
Is your PC switched on?  
Do you see a black screen and the  
indicator in front of the monitor lights up  
green, this means that the display mode is  
not supported.  
Miscellaneous  
. Ambient temperature: + 5~ + 45°C  
. Maximum operating altitude: 2000 m  
. Mains:AC 100-240V  
. Power consumption: around 350W  
. Standby consumption: 1 W  
. Weight (excl. packaging)  
Display: 42.5 kg  
. Dimensions (wxhxd):  
Display: 122.2 x 68.1 x 14.6 cm  
. Wall mounting bracket included  
Switch yourVGA source to a correct  
mode.  
Remote control  
If your monitor no longer responds to the  
remote control, the batteries may be  
exhausted.  
If your problem is not solved:  
Switch your monitor off and then on  
again.  
Never attempt to repair a defective  
monitor yourself.  
Check with your dealer or call aTV  
technician.  
The plasma display technology operates  
with rare gases which are being influenced  
by air pressure. Up to an altitude of 2000  
m above sea-level, the display is  
functioning fine. Operating the set at a  
4

HP Hewlett Packard Hewlett Packard Computer Monitor mx704 User Manual
Epson A882441 User Manual
Eizo Nanao Computer Monitor T2381W User Manual
Eizo FX D7 User Manual
Dell Computer Monitor IN1930 User Manual
Black Box RM900A User Manual
Avocent 180ES User Manual
AT T KX TG5423 User Manual
AT T 7700 User Manual
Apple 073 0562 User Manual