Antec SX1240 User Manual

User’s Manual  
Performance Series  
Computer Enclosures  
SX1240 - Full Tower Case  
This manual is intended only as a guide for  
Antec’s Computer Enclosures. For more  
comprehensive instructions, please refer to  
the user’s manuals which come with your  
components and drives.  
3. Take two pieces of the Tension Clips and mount them onto the sides of  
the 5.25" device. Make sure the metal portion is angled on the outside  
and facing forward.  
4. Slide the device into the drive bay until you hear a clip.  
5. Mount the other devices accordingly.  
6. Connect a large 4-pin white connector from the power supply to the  
male 4-pin connector on each of the devices. After you have finished the  
installation, carefully use your thumbs to push the plastic drive bay covers  
off the bezel and attach the bezel back into the case. Like the metal  
plates, take off the covers that covering the drive bays you are using now.  
IDE Cable Connection  
This is for IDE devices only.  
1. After you have connected the devices to the power supply, you  
need to connect the IDE cables between the devices and the  
motherboard.  
2. For hard drives and CD-ROM’s, use the 40-pin IDE ribbon cables.  
For floppy drives, use the 34-pin ribbon cables. When you connect a ribbon  
cable to a device, make sure that the red strip is toward the power connector.  
3. The side that attaches to devices should be the side that has 2  
connectors. This will enable you to connect another device if you wish.  
4. Connect the far end of the cable to your motherboard on the IDE port.  
Fan Installation  
The case comes with two 80mm fans installed in the rear of the case. The fans are  
installed such that the air is blowing out of the case. The case has 3 optional 80mm fan  
mounts in the front (two of them located inside the drive cages) and 1 optional 92mm  
fan mount in the rear, in addition to the 2 standard 80mm rear mounted fans.  
Note: Antec Cooling Fans blow in the direction that the Antec logo is facing.  
1. Pull the quick release lever towards the rear of the case and release  
the drive cage.  
2. Drop the fan into the cage and push it in until it clips in.  
No screws are needed.  
3
Connect the 4-pin male connector to a 4-pin female connector coming  
out from the power supply.  
3
4
IV. Exclusion Of Damages  
Antec Quality 3 year Warranty  
Antec, Inc., warrants this product to be free from defects resulting from faulty  
manufacture of faulty components under the following terms:  
Antec's sole obligation and liability under this warranty is limited to the repair or  
replacement of a defective product at our option. Antec shall not, in any event, be  
liable to the purchaser or any third party for any incidental or consequential damage,  
(including, but not limited to, damages resulting from interruption of service and loss  
of business), or liability in tort relating to this product or resulting from its use or  
possession.  
a
I. Warranty Length  
Parts and labor are warranted for three (3) years from the date of purchase.  
Replacement products will be warranted for the remainder of the warranty period or  
thirty days, whichever is longer.  
V. Limitations Of Implied Warranties  
There are no other oral or written warranties, expressed or implied, including but not  
limited to those of merchantability or fitness for a particular purpose. The duration of  
implied warranties is limited to the warranty length specified in Paragraph I.  
II. Who Is Protected  
This warranty is enforceable only by the original consumer purchaser.  
VI. State Law And Your Warranty  
III. What Is And Is Not Covered  
This warranty gives you specific legal rights. You may also have other rights granted  
under state law. These rights vary from state to state.  
It is important to note that our warranty is not an unconditional guarantee for the 3-  
year length of the warranty. Antec Products are made from the finest materials avail-  
able under our exacting manufacturing standards. But, like any other product, it is not  
indestructible. Therefore, our warranty does not cover product damage that may  
result from abuse or mishandling of the products, nor does it cover incidental or  
consequential damage.  
VII. Warranty Registration  
It is not necessary to send anything to Antec, Inc. to register your products. In the  
event that warranty service is required, Antec, Inc. will request proof of purchase  
(store receipt or invoice).  
Also, as with any product, it should be expected that component parts, moving parts,  
wheels, etc. will show wear with use over time, and eventually may need to be  
refurbished or replaced. This type of normal wear and tear is naturally not covered by  
our warranty, but we will always be happy to provide you with prompt, high-quality  
repair service at a nominal cost.  
VIII. For Warranty Service  
If the products need repair, return them to the dealer from whom you purchased the  
product. All products returned to Antec for warranty service must have prior  
approval, which your dealer can obtain by calling Antec, Inc. at (510) 770-1200.  
If the repair is required within the warranty period, enclose the proof of purchase with  
the defective product and return it to the dealer. During the warranty period, your  
product will be repaired or replaced without charge, excluding shipping and handling.  
All Antec products are covered by this 3 year warranty except keyboards, monitors  
and any product purchased before the inception of this warranty program which is  
November 1, 2000.  
To return your product for service, package the product securely in its original  
packaging and ship it postpaid. Your dealer or Antec will not be responsible for the  
damage due to shipping. Remember to enclose your proof of purchase and a clear  
description of the problem.  
The following are not covered by the warranty:  
1. Any product on which the serial number has been defaced, modified, or removed.  
2. Damage, deterioration or malfunction resulting from:  
a. Accident, abuse, misuse, neglect, fire, water, lightning, or other acts of nature,  
commercial or industrial use unauthorized product modification or failure to  
follow instructions included with the product.  
b. Repair or attempted repair by anyone not authorized by Antec, Inc.  
c. Any shipment damages (claims must be made with the carrier)  
d. Any other causes which does not relate to a product defect.  
3. Cartons, cases, batteries, cabinets, tapes or accessories used with this product.  
4. Antec, Inc. does not warrant that this product will meet your requirements. It is  
your responsibility to determine the suitability of this product for your purpose.  
5. Removal or installation charges.  
IX. For Out-of-Warranty Service  
If the repair is required after the warranty period there will be a charge for service  
and parts. Contact Antec, Inc. at (510) 770-1200 ext. 330 for a repair estimate on  
your out-of-warranty product.  
X. How To Call For Technical Support At Antec  
If you need help installing or troubleshooting a product call our Technical Support  
Voice Message System at 1-800-22-Antec (1-800-222-6832). Because Antec, Inc.  
wants to provide the convenient and comprehensive technical support our customers  
deserve, our policy is to return your call within one hour if you call during our office  
hours, Monday through Friday, 8:30 a.m. to 5:00 p.m. Pacific Time. The customer  
service line is open 24 hours a day, every day. Messages left after office hours will be  
returned as soon as possible.  
6. Shipping charges.  
7. Any incidental charges.  
7
8

Hasty Bake Portable User Manual
Hanns G HW 216DPB User Manual
GE 2 9926 User Manual
EVGA 111 CD E630 TR User Manual
Elo TouchSystems 1947L User Manual
Electro Voice 1252 User Manual
Dell Computer Monitor E170S User Manual
BenQ FP767 User Manual
Avaya Lucent 2500 MMGN User Manual
Asus WIFI AP P5E3 User Manual