Antec Minuet 350 User Manual

Minuet 350  
User’s Manual  
Manuel de l’utilisateur  
Anwenderhandbuch  
Manuale per l’operatore  
Manual del usuario  
পᡅ䂀ᯢ᳌  
Although care has been taken to prevent sharp edges in your Antec case, we  
strongly recommend taking the appropriate time and caution when working with it.  
Please take reasonable precautions.  
MOTHERBOARD INSTALLATION  
This manual does not cover CPU, RAM, or expansion card installation. Please consult  
your motherboard manual for specific mounting instructions and troubleshooting.  
1. Lay the case down so that the open side is up. You should be able to see the  
drive cage and power supply.  
2. Make sure you have the appropriate I/O panel for the motherboard. If the panel  
provided is not suitable for the motherboard, please contact the motherboard  
manufacturer for the correct I/O panel.  
3. Line up the motherboard with the standoff holes. Determine which holes line  
up and remember where they are. Not all motherboards will match with all of  
the provided screw holes, and this is not necessary for proper functionality.  
Some standoffs may be pre-installed for your convenience.  
4. Remove the motherboard by lifting it up.  
5. Screw in the brass standoffs to the threaded holes that line up with the  
motherboard.  
6. Place the motherboard on the standoffs.  
7. Screw in the motherboard to the standoffs with the provided Phillips-head  
screws.  
8. The motherboard is now installed.  
POWER/LED CONNECTIONS  
The power supply is an ATX12V form factor power supply. It has a single 24-pin  
Main Power Connector, and a 4-pin +12V Power Connector for the motherboard.  
It is backwards compatible to previous ATX form factor power supplies. If your  
motherboard does not support the +12V 4-pin Power Connector, you can still use  
this power supply. It also comes with three 4-pin Peripheral Power Connectors,  
one SATA Power Connector and one 4-pin Floppy Drive Power Connector for your  
drives.  
1. Connect the 24-pin Main Power Connector and  
Picture 2  
Picture 1  
the 4-pin 12V connector to the motherboard  
as needed. If the motherboard uses a 20-pin  
connector, detach the 4-pin attachment on the  
24-pin power connector (see pictures 1 and 2).  
Note: the detachable 4-pin section cannot be  
used in place of a 4-pin +12V connector.  
For 24-pin  
For 20-pin  
motherboards motherboards  
2. Power Switch (labeled POWER SW) connects to the PWR connector on the  
motherboard. Polarity (positive and negative) does not matter for switches.  
3. Connect the Power LED (labeled POWER LED) to your motherboard. For LEDs,  
colored wires are positive (+). White or black wires are negative (–). If the  
LED does not light up when the system is powered on, try reversing the  
connection. For more info on connecting LEDs to your motherboard, see your  
motherboard manual.  
4. Hard Drive LED (labeled HDD LED) connects to the hard drive activity header.  
ADD-IN CARDS  
Make sure that any cards you add to your Minuet 350 case are of the “Low-Profile”  
variety. Your Minuet is a small form factor case and full-height cards will not fit.  
2
CONNECTING THE USB PORTS  
You will find a single 10-pin connector on a cable attached to the front USB ports.  
This Intel standard connector is keyed so that it can’t be accidentally reversed as  
long as it is connected to a proper Intel standard motherboard header. Connect the  
10-pin connector to your motherboard headers so that the blocked pin fits over the  
missing header pin.  
Motherboard USB Pin Layout  
1
2
Pin Signal Names  
Pin Signal Names  
1
3
5
7
9
USB Power 1  
2
4
6
8
USB Power 2  
Negative Signal 2  
Positive Signal 2  
Ground 2  
Negative Signal 1  
Positive Signal 1  
Ground 1  
Key (No Connection)  
10 Empty Pin  
9 10  
Note: Please check your motherboard manual for your USB header pin layout and  
make sure it matches the table.  
CONNECTING THE eSATA PORT  
This case comes with an eSATA port in the front of the case to connect to your  
external SATA devices. You will find a SATA connector on a cable attached to the  
front eSATA ports. Connect it to a SATA connector on your motherboard.  
CONNECTING THE AUDIO PORTS (AC’97 and HDA)  
There is an Intel standard 10-pin AC’97 connector and an Intel 10-pin HDA (High  
Definition Audio) connector. You can connect either of them to your motherboard  
depending on the specification of the motherboard. See instruction below:  
Note: Please check your motherboard manual for your audio header pin layout and  
make sure it matches the table below. Even if your system supports both audio  
standards, you may only connect one connector not both.  
Pin Assignment for Audio Ports (HDA and AC’97)  
Signal Names  
(HDA)  
Signal Names  
(AC’97)  
Pin  
Pin  
1
2
MIC2 L  
AGND  
1
2
MIC In  
GND  
3
MIC2 R  
3
MIC Power  
NC  
10 6 4 2  
9 7 5 3 1  
4
AVCC  
4
5
FRO-R  
5
Line Out (R)  
Line Out (R)  
NC  
6
MIC2_JD  
F_IO_SEN  
Key (no pin)  
FRO-L  
6
7
7
8
8
Key (no pin)  
Line Out (L)  
Line Out (L)  
9
9
10  
LINE2_JD  
10  
3
DRIVE INSTALLATION  
Minuet 350 incorporates a rapid-release Flip Up Drive Cage for easy drive  
installation. The Cage includes three drive bays: one external 5.25”, one external  
3.5”, and one internal 3.5”.  
1. Before installing the external drives, remove the external  
drive bay covers.  
a. To remove the external 5.25” drive bay cover, face the  
front of the case and use your left hand thumb to press  
firmly on the LEFT or outside edge of the left bay cover  
to release it. (See picture 3)  
Picture 3  
b. To remove the external 3.5” drive bay cover, face the  
front of the case and use your right hand thumb to  
press firmly on the RIGHT or outside edge of the right  
bay cover to release it. (See picture 4)  
2. Lift up and slide the drive cage from the case.  
3. Place the cage upside down on a flat surface.  
Note: You must install the external devices first, before  
installing the internal 3.5” device.  
4. Slide the external 5.25” device into the drive cage from  
the front. Since the drive cage is upside down, your drive  
should be too so that it will be properly orientated once the  
cage is installed in the Minuet 350.  
5. Align the bottom rear screw holes (one at each side) on the  
device with the two screw holes (the pair closest to the  
front of the cage) on the cage and fasten the device with  
the screws provided. (See picture 5)  
6. Slide the external 3.5” device into the drive cage from  
the front. Since the drive cage is upside down, your drive  
should be too so that it will be properly orientated once the  
cage is installed in the Minuet 350.  
7. Align the bottom rear screw holes (one at each side) on the  
device with the two screw holes on the cage and fasten the  
device with the screws provided. (See picture 6)  
8. To install the internal 3.5” device, find the two mounting  
prongs on one side of the bay. With one hand holding the  
device at a 45-degree angle with the bottom side up, align  
the two screw holes on one side of the device with the  
prongs and slide the device into the bay. (See picture 7)  
9. Fasten the other side of the device to the two tabs with the  
screws provided. (See picture 8.)  
10. When sliding the Cage back into the case, work slowly and  
carefully to ensure that the front panels of the external de-  
vices align properly with the holes provided for them in the  
bezel.  
Picture 4  
Picture 5  
Picture 6  
Picture 7  
Picture 8  
11. Connect power to each of the devices.  
4
COOLING SYSTEM  
The Side 80mm TriCool™ fan:  
This case comes with one 80mm TriCool side fan installed. This fan has a three-speed  
switch that lets you choose the speed that best suits your needs. The default  
setting is Low. See the following specifications.  
Specifications:  
Size:  
Rated Voltage:  
Operating Voltage:  
80 x 80 x 25.4mm  
12V  
10.2V ~ 13.8V  
Input  
Current  
Acoustical  
Noise  
Input  
Power  
Speed  
Air Flow  
Static Pressure  
High  
2600 RPM  
0.2A  
(Max.)  
0.96 m³ / min  
(34 CFM)  
3.04 mm-H2O  
(0.12 inch-H2O)  
30 dBA  
2.4W  
Medium  
2000 RPM  
0.74 m³ / min  
(26 CFM)  
1.79 mm-H2O  
(0.07 inch-H2O)  
0.15A  
0.1A  
24 dBA  
18 dBA  
1.8W  
1.2W  
Low  
1500 RPM  
0.55 m³ / min  
(20 CFM)  
1.00 mm-H2O  
(0.03inch-H2O)  
Ventilation  
Top Panel:  
Minuet 350 comes with a vented top panel for maximum cooling capacity. It will  
help the airflow inside the case maximizing ventilation and cooling.  
Rear Panel:  
Minuet 350 comes with vents above the I/O panel.  
Note: Do NOT install exhausts fans over these vents as they are designed to  
take in fresh air to help cool the CPU.  
5
Antec, Inc.  
47900 Fremont Blvd.  
Fremont, CA 94538  
USA  
tel: 510-770-1200  
fax: 510-770-1288  
Antec Europe B.V.  
Stuttgartstraat 12  
3047 AS Rotterdam  
The Netherlands  
tel: +31 (0) 10 462-2060  
fax: +31 (0) 10 437-1752  
Customer Support:  
US & Canada  
1-800-22ANTEC  
Europe  
+31 (0) 10 462-2060  
© Copyright 2007 Antec, Inc. All rights reserved.  
All trademarks are the property of their respective owners.  
Reproduction in whole or in part without written permission is prohibited.  
Printed in China.  
34  

Global Upholstery Co 3307568 User Manual
GE Monogram PROFILE JV535H User Manual
GE DECT 28165 User Manual
Edirol PC 50 User Manual
DCS CT 304WT User Manual
BT 1250 Classic User Manual
Black Box Computer Hardware VX HDMI IP VTX User Manual
Belkin F8E846UKBNDL User Manual
AT T E5804 User Manual
Aluratek AHDUS350 User Manual