Acnodes RMC 7152 User Manual

RMC 7152  
14” short depth server  
Installation Guide  
RMC 7152: 14” short depth server with two Intel Xeon  
processors  
1
© Copyright 2009 Acnodes, Inc.  
661 Brea Canyon Rd., Suite 3  
Walnut, CA 91789  
All rights reserved. Product description and product specifications  
are subject to change without notice. For latest product information,  
please visit Acnodes’ web site at www.acnodes.com.  
RMC 7152  
14” short depth server  
Installing the Chassis Rails  
Position the fixed chassis rail sections you just removed along the side of the chassis making sure the five screw holes line up.  
Note that these two rails are left/right specific. Screw the rail securely to the side of the chassis (see Figure  
2-2). Repeat this procedure for the other rail on the other side of the chassis. You will also need to attach the rail brackets  
when installing into a telco rack.  
Locking Tabs: As you have seen, both chassis rails have a locking tab, which serves two functions. The first is to lock the  
server into place when installed and pushed fully into the rack, which is its normal position. Secondly, these tabs also lock the  
server in place when fully extended from the rack. This prevents the server from coming completely out of the rack when you  
pull it out for servicing.  
3
© Copyright 2009 Acnodes, Inc.  
661 Brea Canyon Rd., Suite 3  
Walnut, CA 91789  
All rights reserved. Product description and product specifications  
are subject to change without notice. For latest product information,  
please visit Acnodes’ web site at www.acnodes.com.  
RMC 7152  
14” short depth server  
15-inch touch panel PC  
Installing the Rack Rails  
Determine where you want to place the RMC 7152 in the rack (see Rack and Server Precautions in Section 2-3). Position the  
fixed rack rail/sliding rail guide assemblies at the desired location in the rack, keeping the sliding rail guide facing the inside of  
the rack. Screw the assembly securely to the rack using the brackets provided. Attach the other assembly to the other side of  
the rack, making sure that both are at the exact same height and with the rail guides facing inward.  
Installing the Server Into the Rack  
You should now have rails attached to both the chassis and the rack unit. The next step is to install the server into the rack. Do  
this by lining up the rear of the chassis rails with the front of the rack rails. Slide the chassis rails into the rack rails, keeping  
the pressure even on both sides (you may have to depress the locking tabs when inserting). See Figure 2-3.  
When the server has been pushed completely into the rack, you should hear the locking tabs "click".  
4
© Copyright 2009 Acnodes, Inc.  
661 Brea Canyon Rd., Suite 3  
Walnut, CA 91789  
All rights reserved. Product description and product specifications  
are subject to change without notice. For latest product information,  
please visit Acnodes’ web site at www.acnodes.com.  
RMC 7152  
14” short depth server  
Installing the Server into a Telco Rack  
If you are installing the RMC 7152 into a Telco type rack, follow the direc- tions given on the previous pages for rack installa-  
tion. The only difference in the installation procedure will be the positioning of the rack brackets to the rack. They should be  
spaced apart just enough to accomodate the width of the telco rack.  
5
© Copyright 2009 Acnodes, Inc.  
661 Brea Canyon Rd., Suite 3  
Walnut, CA 91789  
All rights reserved. Product description and product specifications  
are subject to change without notice. For latest product information,  
please visit Acnodes’ web site at www.acnodes.com.  

HP Hewlett Packard FP17 User Manual
Fisher Paykel OR60 User Manual
Envision Peripherals EN 780e 17 User Manual
Dell POWEREDGE M620 User Manual
Cypress FLEx36 CYD04S36V User Manual
Creda CHATSWORTH 41301 User Manual
Clarity D724 User Manual
Binatone SPEAKEASY COMBO 2005 TRIPLE User Manual
AT T E2520 User Manual
AOC 7KLR User Manual