|
FPC 8059
5.7” VGA TFT
Fan less Touch Panel PC
User’s Manual
Disclaimers
The information in this manual has been carefully checked and is believed to
be accurate. Acnodes Corp assumes no responsibility for any
infringements of patents or other rights of third parties, which may result from
its use.
Acnodes Corp assumes no responsibility for any inaccuracies that may
be contained in this document. Acnodes Corp makes no commitment to
update or
to keep current the information contained in this manual.
Acnodes Corp reserves the right to make improvements to this document
and/or product at any time and without notice.
No part of this document may be reproduced, stored in a retrieval system, or
transmitted, in any form or by any means, electronic, mechanical,
photocopying, recording, or otherwise, without the prior written permission of
Acnodes Corp.
♥
C
opyright 2007 by Acnodes Corp.
ll rights reserved.
September 2007, Ver
A
s
ion A1
1
Safety Approvals
m
CE Marking
FCC Class A
m
FCC Compliance
This equipment has been tested and complies with the limits for a
Class A digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. If not installed and used in
accordance with proper instructions, this equipment might generate or
radiate radio frequency energy and cause harmful interference to
radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the
following measurers:
1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment and receiver.
3. Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
4. Consult the dealer or an experienced radio/TV technician for help.
Shielded interface cables must be used in order to comply with
emission limits.
Safety Precautions
Before getting started, read the following important cautions.
1. The FPC 8059 does not come equipped with an operating
system. An operating system must be loaded first before
installing any software into the computer.
2. Be sure to ground yourself to prevent static charge when
installing the internal components. Use a grounding wrist strap
and place all electronic components in any static-shielded
devices. Most electronic components are sensitive to static
electrical charge.
3. Disconnect the power cord from the FPC 8059 before
making any installation. Be sure both the system and the
external devices are turned OFF. Sudden surge of power
could ruin sensitive components. Make sure the FPC 8059
is properly grounded.
4. The brightness of the flat panel display decreases with usage.
However, hours of use vary depending on the application
environment.
5. Turn OFF the system power before cleaning. Clean the
system using a cloth only. Do not spray any liquid cleaner
directly onto the screen. The FPC 8059 comes with a touch
screen. Although the touch screen is chemical resistant, it is
recommended that you spray the liquid cleaner on a cloth first
before wiping the screen. In case your system comes without
the touch screen, you must follow the same procedure and not
spray any cleaner on the flat panel directly.
6. Avoid using sharp objects to operate the touch screen.
Scratches on the touch screen may cause malfunction or
internal failure to the touch screen.
7. The flat panel display is not susceptible to shock or vibration.
When assembling the FPC 8059, make sure it is securely
installed.
1
5. Do not open the system’s back cover. If opening the cover for
maintenance is a must, only a trained technician is allowed to do
so. Integrated circuits on computer boards are sensitive to static
electricity. To avoid damaging chips from electrostatic discharge,
observe the following precautions:
ꢀ
Before handling
a
board or integrated circuit, touch an
unpainted portion of the system unit chassis for a few seconds.
This will help to discharge any static electricity on your body.
ꢀ
When handling
boards and components, wear
a
wrist-grounding strap, available from most electronic
component stores.
Trademarks Acknowledgments
Acnodes Corp is a trademark of Acnodes Corp.
IBM, PC/AT, PS/2, VGA are trademarks of International
Business Machines Corp.
Intel and Pentium are trademarks of Intel Corp.
MS-DOS, Microsoft C and Quick BASIC are trademarks of
Microsoft Corp.
VIA is a trademark of VIA Technologies, Inc.
SST is a trademark of Silicon Storage Technology, Inc.
UMC is a trademark of United Microelectronics Corp.
Other brand names and trademarks are the properties of their
respective owners.
This page does not contain any information.
3
Table of Contents
D
isclaimers........................................................................ii
Safety Approvals................................................................iii
FCC Compl ance ..............................................................iii
i
Safety Precautions ............................................................. iv
C h a p t e r 1 .....................................................................1
Introduction ..........................................................................1
1.1
Genera
l
Descript
ion ............................................1
1.2
Spec cat
i
f
i
i
ons ......................................................2
1.2.1
Main CPU board....................................................2
I/O System .............................................................2
System Specification............................................3
1.2.2
1.2.3
1.3
1.4
1.5
D
i
mens
i
ons ..........................................................
3
5
6
I/O Out
lets ............................................................
Package list..........................................................
C h a p t e r 2 .....................................................................7
Hardware Installation.........................................................7
2.1
2.2
2.3
2.4
2.5
CompactFlash Card
PC 104 nstallat on ..............................................
Seria Port nterface ..........................................10
Ethernet ..............................................................11
Mount ng Way : Pane mount...........................11
Installation........................8
/
I
i
9
l
I
i
l
C h a p t e r 3 ...................................................................12
Windows CE.Net................................................................12
3.1
Survey Form.......................................................12
3.2
Calibrate Touch Screen....................................12
Table of Contents
vii
FPC 8059 User’s Manual
C h a p t e r 1
Introduction
This chapter contains the general information and the detail
specifications of the FPC 8059. Chapter 1 includes the following
sections:
f
f
f
f
f
General Description
System Specification
Dimensions
I/O Outlets
Package List
1.1 Genera Description
l
The FPC 8059 is a 5.7” fan less TFT VGA touch panel computer. It
is equipped with CISI-based low power consumption processor, AMD
LX800.
By supporting the option of external battery set, the FPC 8059 can
continue system operation if a main power shortage ever happens. In
addition, the PC/104 and Mini-PCI slots are reserved for expansion
availability.
The FPC 8059 supports Compact Flash card and is the best choice
for applications of factory automation, machinery maker, building
automation and semi-conductor.
Introduction
1
FPC 8059 User’s Manual
1.2 Specifications
1.2.1 Main CPU board
f
f
f
CPU: AMD LX800 500MHz
System Chipset: AMD LX + CS5536AD
BIOS: Phoenix-Award 4Mbit with RPL/PXE Ethernet Boot
ROM, Smartview and customer CMOS backup.
f
System Memory: One 184-pin DDR DIMM
Maximum up to 1GB
1.2.2 I/O System
f
−
−
Standard I/O:
2 x serial ports (1 x RS-232, 1 x RS-232/422/485)
2 x USB Ports 2.0 compliant
f
Ethernet
Equipped with 1 x RJ-45 for 10/100 base-T
Audio
:
f
:
Realtek AC’97 codec audio (Line-out)
Expansion:
f
f
Equipped with 1 x Mini-PCI & 1 x PC/104
Compact Flash Socket:
One Compact Flash Type II Socket
Introduction
2
FPC 8059 User’s Manual
1.2.3 System Specification
f
f
5.7” VGA TFT LCD
Disk drive housing:
−
1 x Compact Flash Type II Socket
DC 24V power supply
Heat dispensing design
Net weight:
f
f
f
−
2.0 Kgs
f
f
f
f
f
f
Dimension (main body size):
−
208.5 x 167.3 x 66.5 mm
Operating temperature:
−
O° to 45°C ; Relative umidity:50%
Relative humidity:
−
10% to 85% @ 40° C, non-condensing
Altitude:
−
10,000 ft. (3,000 meters)
Vibration (operating):
−
5 to 500 Hz, 1 G random
Shock (operating):
−
10 G peak acceleration (11 msec. duration)
1.3 Dimensions
The following diagrams show the dimensions and outlines of
FPC 8059.
Introduction
3
FPC 8059 User’s Manual
Introduction
4
FPC 8059 User’s Manual
1.4 I/O Outlets
The following figure shows the I/O locations of the FPC 8059.
1:
2:
3:
4:
5:
Power Switch
6:
7:
8:
LAN
DC power connector
COM 2 (RS-232)
USB 2.0 x 2
Line-out
COM 1 (RS-232/422/485) 9:
CompactFlash card
PC/104 slot
Introduction
5
FPC 8059 User’s Manual
1.5 Package list
When you receive the FPC 8059, there are following items in the
package. If you can not find it, please contact Acnodes Corp.
distributors.
1. FPC 8059 x 1
2. Panel mount kit x 6
3. Driver CD x1
Introduction
6
FPC 8059 User’s Manual
C h a p t e r 2
Hardware Installation
The FPC 8059 provides rich I/O ports and flexible expansions for
you to meet different demand such as PCMCIA, WLAN module and
so on. The chapter will show you how to install the hardware. It
includes :
f
f
f
f
f
Compact Flash Card
PC/104
Serial Port
Ethernet
Mounting Way
8
Hardware Installation
FPC 8059 User’s Manual
2.1 CompactFlash Card Installation
FPC 8059 offers one CF slot for users to install Compact Flash card.
Please refer to the following instructions and illustration:
1. Remove the rubber cover at left-side.
2. Install Compact Flash card in the FPC 8059.
Hardware Installation
9
FPC 8059 User’s Manual
2.2 PC/104 Installation
The FPC 8059 offers a convenient expansion for users to install
PC/104 module such as PCMCIA, WLAN, COM port card and so on.
Please follow the steps:
1. Unscrew screws to remove the bracket.
2. Install PC/104 module.
10
Hardware Installation
FPC 8059 User’s Manual
2.3 Serial Port Interface
The FPC 8059
has two onboard serial ports, COM1
(RS-232/422/485) & COM2 (RS-232).
The pin assignments are listed below:
Description
1
2
3
4
5
6
7
8
9
Data Carrier Detect (DCD)
Receive Data (RXD)
Transmit Data (TXD)
Data Terminal Ready (DTR)
Ground (GND)
Data Set Ready (DSR)
Request to Send (RTS)
Clear to Send (CTS)
Ring Indicator (RI)
In addition, COM1 can be set for RS-232/422/485 by jumper. The
jump setting is listed as below:
COM1
JP12
JP10
JP11
RS-232 (default)
RS-422
1-2
3-5, 4-6
3-5, 4-6
3-4, 7-8
5-6, 7-8
1-3, 2-4
1-3, 2-4
1-3, 2-4
1-3, 2-4
RS-485
COM2
COM1
Hardware Installation
11
FPC 8059 User’s Manual
2.4 Ethernet
The FPC 8059 provides an NE2000 compatible Ethernet (RJ-45)
interface. For network connection, just plug in one cable end of the
FPC 8059 10/100 Base-T Hub into the standard RJ-45 connector.
The pin assignment of the RJ-45 is listed below;
Pin
Signal
1
2
3
4
5
6
7
8
TX+ (Data transmission positive
TX- (Data transmission negative)
Rx+(Data reception positive)
RJ45 termination
8
1 2 3 4 5 6 7
RJ45 termination
Rx- (Data reception negative)
RJ45 termination
RJ-45
RJ45 termination
2.5 Mounting Way : Panel mount
The FPC 8059 is designed for panel mount application. To mount
the FPC 8059, the standard set of mounting kit (included in the
system packaging) is needed.
12
Hardware Installation
FPC 8059 User’s Manual
C h a p t e r 3
Windows CE.Net
3.1 Survey Form
Compact Flash Card
System Memory Support
Multiple I/O
e
e
e
e
e
e
e
e
e
e
e
32MB ~ 2GB
256MB ~ 1GB
Parallel Port
3 x UARTs compliant Serial Ports
2 x USB 1.1
PS/2 Keyboard & Mouse
USB Keyboard & Mouse
320 x 240
Realtek 8139x/810x 10/100M
Line-out
USB 2.0
Keyboard & Mouse
Display (MS Flat)
Ethernet
Audio
Touch Screen
5-wire Resistive type
3.2 Calibrate Touch Screen
This image includes a Touch Screen on COM3. To calibrate it,
do the following steps:
1. Start\Programs\PenMount TouchPanel\Calibration
2. 3 types of calibration mode selection (4/9/16 points)
12
Appendix
|