Acer LCD Monitor
User's Guide
iii
Special notes on LCD monitors
The following are normal with the LCD monitor and do not indicate a problem.
•
Due to the nature of the fluorescent light, the screen may flicker during
initial use. Turn off the power switch and then turn it on again to make
sure the flicker disappears.
•
•
•
You may find slightly uneven brightness on the screen depending on the
desktop pattern you use.
The LCD screen has 99.99% or more effective pixels. It may include
blemishes of 0.01% or less such as a missing pixel or a pixel lit all the time.
Due to the nature of the LCD screen, an afterimage of the previous screen
may remain after switching the image, when the same image is displayed
for hours. In this case, the screen is recovered slowly by changing the image
or turning off the power switch for a few hours.
Information for your safety and
comfort
Safety instructions
Read these instructions carefully. Keep this document for future reference.
Follow all warnings and instructions marked on the product.
Cleaning your monitor
Please carefully follow these guidelines when cleaning the monitor:
•
•
Always unplug the monitor before cleaning.
Use a soft cloth to wipe the screen and cabinet front and sides.
Connecting/disconnecting the device
Observe the following guidelines when connecting and disconnecting power
from the LCD monitor:
•
•
•
Make sure the monitor is attached to its base before connecting the power
cord to the AC power outlet.
Make sure both the LCD monitor and the computer are turned off before
connecting any cable or unplugging the power cord.
If the system has multiple sources of power, disconnect power from the
system by unplugging all power cords from the power supplies.
iv
Accessibility
Be sure that the power outlet you plug the power cord into is easily accessible
and located as close to the equipment operator as possible. When you need to
disconnect power from the equipment, be sure to unplug the power cord from
the electrical outlet.
Safe listening
To protect your hearing, follow these instructions.
•
Gradually increase the volume until you can hear it clearly and comfortably
and without distortion.
•
After setting the volume level, do not increase it after your ears have
adjusted.
•
•
•
Limit the amount of time listening to music at high volume.
Avoid turning up the volume to block out noisy surroundings.
Turn the volume down if you can't hear people speaking near you.
Warnings
•
•
Do not use this product near water.
Do not place this product on an unstable cart, stand or table. If the product
falls, it could be seriously damaged.
•
Slots and openings are provided for ventilation to ensure reliable
operation of the product and to protect it from overheating. These
openings must not be blocked or covered. The openings should never be
blocked by placing the product on a bed, sofa, rug or other similar surface.
This product should never be placed near or over a radiator or heat
register, or in a built-in installation unless proper ventilation is provided.
•
Never push objects of any kind into this product through cabinet slots as
they may touch dangerous voltage points or short-out parts that could
result in a fire or electric shock. Never spill liquid of any kind onto or into
the product.
•
•
To avoid damage of internal components and to prevent battery leakage,
do not place the product on a vibrating surface.
Never use it under sporting, exercising, or any vibrating environment
which will probably cause unexpected short current or damage internal
devices.
Using electrical power
•
This product should be operated from the type of power indicated on the
marking label. If you are not sure of the type of power available, consult
your dealer or local power company.
•
•
Do not allow anything to rest on the power cord. Do not locate this
product where people will walk on the cord.
If an extension cord is used with this product, make sure that the total
v
ampere rating of the equipment plugged into the extension cord does not
exceed the extension cord ampere rating. Also, make sure that the total
rating of all products plugged into the wall outlet does not exceed the fuse
rating.
•
•
Do not overload a power outlet, strip or receptacle by plugging in too
many devices. The overall system load must not exceed 80% of the branch
circuit rating. If power strips are used, the load should not exceed 80% of
the power strip's input rating.
This product's power cord is equipped with a three-wire grounded plug.
The plug only fits in a grounded power outlet. Make sure the power outlet
is properly grounded before inserting the power cord plug. Do not insert
the plug into a non-grounded power outlet. Contact your electrician for
details.
Warning! The grounding pin is a safety feature. Using a power
outlet that is not properly grounded may result in electric shock
and/or injury.
Note: The grounding pin also provides good protection from
unexpected noise produced by other nearby electrical devices that
may interfere with the performance of this product.
•
Use the product only with the supplied power supply cord set. If you need
to replace the power cord set, make sure that the new power cord meets
the following requirements: detachable type, UL listed/CSA certified, type
SPT-2, rated 7 A 125 V minimum, VDE approved or its equivalent, 4.6
meters (15 feet) maximum length.
Product servicing
Do not attempt to service this product yourself, as opening or removing covers
may expose you to dangerous voltage points or other risks. Refer all servicing to
qualified service personnel.
Unplug this product from the wall outlet and refer servicing to qualified service
personnel when:
.
the power cord or plug is damaged, cut or frayed
•
•
•
•
•
.
liquid was spilled into the product
the product was exposed to rain or water
.
the product has been dropped or the case has been damaged.
the product exhibits a distinct change in performance, indicating a need
for service.
•
the product does not operate normally after following the operating
.
instructions
vi
Note: Adjust only those controls that are covered by the operating
instructions, since improper adjustment of other controls may
result in damage and will often require extensive work by a
qualified technician to restore the product to normal condition.
Potentially explosive environments
Switch off your device in any area with a potentially explosive atmosphere and
obey all signs and instructions. Potentially explosive atmospheres include areas
where you would normally be advised to turn off your vehicle engine. Sparks in
such areas could cause an explosion or fire resulting in bodily injury or even
death. Switch off the device near gas pumps at service stations. Observe
restrictions on the use of radio equipment in fuel depots, storage and
distribution areas; chemical plants; or where blasting operations are in progress.
Areas with a potentially explosive atmosphere are often, but not always,
marked. They include below deck on boats, chemical transfer or storage
facilities, vehicles using liquefied petroleum gas (such as propane or butane),
and areas where the air contains chemicals or particles such as grain, dust or
metal powders.
Additional safety information
Your device and its enhancements may contain small parts. Keep them out of
the reach of small children.
IT Equipment Recycling Information
Acer is strongly committed to environmental protection and views recycling, in
the form of salvaging and disposal of used equipment, as one of the company's
top priorities in minimizing the burden placed on the environment.
We at Acer are very conscious of the environmental effects of our business and
strive to identify and provide the best working procedures to reduce the
environmental impact of our products.
For more information and help when recycling, please go to this website:
of our other products.
vii
Disposal instructions
Do not throw this electronic device into the trash when discarding.
To minimize pollution and ensure utmost protection of the global environment,
please recycle. For more information on the Waste from Electrical and
Electronics Equipment (WEEE) regulations, visit
LCD pixel statement
The LCD unit is produced with high-precision manufacturing techniques.
Nevertheless, some pixels may occasionally misfire or appear as black or
red dots. This has no effect on the recorded image and does not constitute
a malfunction.
viii
This product has been shipped enabled for power management:
•
•
•
Activate display’s Sleep mode within 15 minutes of user inactivity.
Activate computer’s Sleep mode within 30 minutes of user inactivity.
Wake the computer from Sleep mode by pushing the power button.
Tips and information for comfortable use
Computer users may complain of eyestrain and headaches after prolonged use.
Users are also at risk of physical injury after long hours of working in front of a
computer. Long work periods, bad posture, poor work habits, stress,
inadequate working conditions, personal health and other factors greatly
increase the risk of physical injury.
Incorrect computer usage may lead to carpal tunnel syndrome, tendonitis,
tenosynovitis or other musculoskeletal disorders. The following symptoms may
appear in the hands, wrists, arms, shoulders, neck or back:
.
•
•
•
•
•
numbness, or a burning or tingling sensation
.
aching, soreness or tenderness
pain, swelling or throbbing
stiffness or tightness.
.
.
coldness or weakness
If you have these symptoms, or any other recurring or persistent discomfort
and/or pain related to computer use, consult a physician immediately and
inform your company's health and safety department.
The following section provides tips for more comfortable computer use.
Finding your comfort zone
Find your comfort zone by adjusting the viewing angle of the monitor, using a
footrest, or raising your sitting height to achieve maximum comfort. Observe
the following tips:
•
•
•
refrain from staying too long in one fixed posture.
avoid slouching forward and/or leaning backward
.
stand up and walk around regularly to remove the strain on your leg
.
muscles
ix
Taking care of your vision
Long viewing hours, wearing incorrect glasses or contact lenses, glare, excessive
room lighting, poorly focused screens, very small typefaces and low-contrast
displays could stress your eyes. The following sections provide suggestions on
how to reduce eyestrain.
Eyes
•
•
Rest your eyes frequently.
Give your eyes regular breaks by looking away from the monitor and
focusing on a distant point.
•
Blink frequently to keep your eyes from drying out.
Display
•
•
Keep your display clean.
Keep your head at a higher level than the top edge of the display so your
eyes point downward when looking at the middle of the display.
•
•
Adjust the display brightness and/or contrast to a comfortable level for
enhanced text readability and graphics clarity.
Eliminate glare and reflections by:
•
placing your display in such a way that the side faces the window or
.
any light source
•
•
•
•
•
minimizing room light by using drapes, shades or blinds.
using a task light.
.
changing the display's viewing angle
using a glare-reduction filter.
using a display visor, such as a piece of cardboard extended from the
display's top front edge
.
•
•
Avoid adjusting your display to an awkward viewing angle.
Avoid looking at bright light sources, such as open windows, for extended
periods of time.
Developing good work habits
Develop the following work habits to make your computer use more relaxing
and productive:
•
•
•
•
Take short breaks regularly and often.
Perform some stretching exercises.
Breathe fresh air as often as possible.
Exercise regularly and maintain a healthy body.
x
Declaration of Conformity
We,
Acer Incorporated
8F, 88, Sec. 1, Hsin Tai Wu Rd., Hsichih, Taipei Hsien 221, Taiwan
Contact Person: Mr. Easy Lai, E-mail: [email protected]
And,
Acer Europe SA
Via Cantonale, Centro Galleria 2 6928 Manno Switzerland
Hereby declare that:
Product:
LCD Monitor
Acer
V193L
Trade Name:
Model Number:
SKU Number:
V193L
xxxxxx (“x” = 0~9, a ~ z, or A ~ Z)
Is compliant with the essential requirements and other relevant provisions of the following EC directives,
and that all the necessary steps have been taken and are in force to assure that production units of the
same product will continue comply with the requirements.
EMC Directive 2004/108/EC as attested by conformity with the following harmonized
standards:
-. EN55022, AS/NZS CISPR22 Class B.
-. EN55024
-. EN61000-3-2, Class D
-. EN61000-3-3
Low Voltage Directive 2006/95/EC as attested by conformity with the following
harmonized standard:
-. EN60950-1
RoHS Directive 2002/95/EC on the Restriction of the Use of certain Hazardous Substances
in Electrical and Electronic Equipment:
-. The maximum concentration values of the restricted substances by weight in homogenous material are:
Lead
Mercury
0.1% Polybrominated Biphenyls (PBB’s)
0.1% Polybrominated Diphenyl Ethers (PBDE’s) 0.1%
0.01%
0.1%
Hexavalent Chromium 0.1% Cadmium
Directive 2009/125/EC with regard to establishing a framework for the setting of
ecodesign requirements for energy-related product.
Year to begin affixing CE marking 2010.
_______________________________
Easy Lai /Manager
Regulation, Acer Inc.
Jul. 15, 2010
Date
xi
Federal Communications Commission
Declaration of Conformity
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may
cause undesired operation.
The following local Manufacturer /Importer is responsible for this declaration:
Product:
LCD Monitor
V193L
Model Number:
SKU Number:
V193L xxxxxx
(“x” = 0~9, a ~ z, A ~ Z or Blank)
Name of Responsible Party:
Acer America Corporation
Address of Responsible Party: 333 West San Carlos St.
San Jose, CA 95110
U. S. A.
Contact Person:
Phone No.:
Fax No.:
Acer Representative
254-298-4000
254-298-4147
xii
1
IT equipment recycling information
vi
Federal Communications Commission
How to adjust a setting
9
2
1
Unpacking
Please check that the following items are present when you unpack the box,
and save the packing materials in case you need to ship or transport the
monitor in the future.
LCD monitor
User’s guide
Quick start guide
D-sub cable
(optional)
DVI cable
(optional)
AC power cord
Audio Cable
(optional)
2
Attaching/removing the base
Attaching:
Removing:
Align the release button on the
Press the release button as
indicated, then pull in the direction
of the arrow to remove the base.
bottom of the monitor with the
corresponding slots on the bottom of
the base.
Screen position adjustment
To optimize the viewing position, you can adjust the monitor tilt by using
both of your hands to hold the edges of the monitor as shown below.
The monitor can be adjusted to 15 degrees up or 5 degrees down.
3
Connecting the power cord
•
Check first to make sure that the power cord you use is the correct type
required for your area.
•
The monitor has a universal power supply that allows operation in either
100/120 V AC or 220/240 V AC voltage area. No user-adjustment is
required.
•
•
•
Plug one end of the power cord to the AC inlet, and plug the other end
into an AC outlet.
For units using 120 V AC:
Use a UL-listed cord set, type SVT wire and plug rated 10 A/125 V.
For units using 220/240 V AC:
Use a cord set consisting of H05VV-F cord and plug rated 10 A/250 V. The
cord set should have the appropriate safety approvals for the country in
which the equipment will be installed.
Power saving
The monitor will be switched to "power saving" mode by the control signal
from the display controller, as indicated by the amber-colored power LED.
Mode
On
LED light
Blue
Power saving
Amber
The power saving mode will be kept until a control signal has been detected or
the keyboard or mouse is activated. The recovery time from "power saving"
mode back to "on" is around 3 seconds.
Display Data Channel (DDC)
To make installation easier, so long as your system supports the DDC protocol,
the monitor is able to plug-and-play. The DDC is a communication protocol
through which the monitor automatically informs the host system about its
capabilities; for example, supported resolutions and corresponding timing. The
monitor supports the DDC2B standard.
5
24-pin color display signal cable
*
PIN No.
Description
TMDS data 2-
PIN No.
13
Description
1
2
NC
TMDS data 2+
TMDS data 2/4 shield
NC
14
+5 V power
3
15
GND (return for +5 V hsync.vsync)
Hot-plug detection
TMDS data 0-
4
16
5
NC
17
6
DDC clock
DDC data
NC
18
TMDS data 0+
7
19
TMDS data 0/5 shield
NC
8
20
9
TMDS data 1-
TMDS data 1+
TMDS data 1/3 shield
NC
21
NC
10
11
12
22
TMDS clock shield
TMDS clock+
23
24
DDC TMDS clock-
* only for certain models
6
Standard timing table
Mode
Resolution
1
2
VGA
VGA
640 x 480
60
Hz
Hz
Hz
Hz
Hz
Hz
Hz
Hz
Hz
Hz
Hz
Hz
Hz
Hz
Hz
640 x 480
640 x 480
640 x 480
720 x 400
800 x 600
800 x 600
800 x 600
800 x 600
832 x 624
1024 x 768
1024 x 768
1024 x 768
1152 x 870
1152 x 864
72
3
VGA
75
4
66.66
70
MAC
VESA
SVGA
SVGA
SVGA
SVGA
MAC
XGA
5
6
56
7
60
8
72
9
75
10
11
12
13
14
15
74.55
60
XGA
70
XGA
75
MAC
VESA
75
75
16
VESA
1280 x 9
60
Hz
Hz
60
17
SXGA
1280 x 1024
1280 x 1024
60
18
75
Hz
SXGA
7
Installation
To install the monitor on your host system, please follow the steps below:
Steps
1
Connect the video cable
a
b
c
Make sure both the monitor and computer are switched off.
Connect the VGA video cable to the computer.
Connect the digital cable (only for dual-input models).
(1) Make sure both the monitor and computer are switched off.
(2) Connect one end of the 24-pin DVI cable to the back of the
monitor and the other end to the computer's port.
2
3
4
Connect the power cord
Connect the power cord to the monitor, then to a properly grounded AC
outlet.
Turn on the monitor and computer
Turn on the monitor first, then the computer. This sequence is very
important.
If the monitor does not function properly, please refer to the
troubleshooting section to diagnose the problem.
DVI
D-Sub
2
1-1
1-2
1-1
1-2
2
8
User controls
Front panel controls
1
2
Power LED: Lights up to indicate the power is turned on.
Power Switch: Turn the power on or off.
3.4 < / > : Press < or > to navigate to the desired function, press Enter to
select the function. Press < or > to change the settings of the
current function.
5
Menu/Enter: Activate the OSD menu when the OSD is off or activate
/ deactivate the adjustment function when the OSD is on.
Auto adjust button/Exit:
6
a. When the OSD menu is active, this button will act as the exit key
(exit OSD menu).
b. When the OSD menu is inactive, press this button for two seconds to
activate the Auto Adjustment function. The Auto Adjustment function
is used to set the HPos, VPos, Clock and Focus.
/Exit:
7
a. When the OSD menu is active, this button will act as the exit key
(exit OSD menu).
b. When the OSD menu is inactive, press this button to select scenario
mode.
9
How to adjust a setting
1
2
3
Press the Menu button to activate the OSD window.
Press < or > to select the desired function.
Press the Menu button again to select the function that you want to
adjust.
4
5
Press < or > to change the settings of the current function.
To exit and save, select the exit function. If you want to adjust any other
function, repeat steps 2 to 4.
A. Acer eColor Management: If "Acer eColor Management" is selected,
the Acer eColor Management OSD will appear.
B. User: If "User" is selected, the standard OSD will appear.
I. Only analog-input mode
II. Only digital-input mode
10
Acer eColor Management
•
Operation instructions
1
Press the
Empowering Key to open the Acer eColor Management
OSD and access the scenario modes.
2
3
Press "<" or ">" to select the mode.
Press the Auto-adjust button to confirm the mode and run Auto
Adjust.
User
mode
ECO
mode
Standard
mode
Graphic
mode
Movie
mode
•
Features and benefits
Main
menu
icon
Sub menu item
User mode
Description
User-defined. Settings can be fine-tuned to
suit any situation.
ECO mode
Adjusts the settings to reduce power
consumption.
Standard mode
Default settings. Reflects native display
capability.
Graphic mode
Movie mode
Enhances colors and emphasizes fine detail.
Pictures and photographs appear in vibrant
colors with sharp detail.
Displays scenes in clearest detail. Presents
great visuals, even in unsuitably-lit
environments.
11
User
Main
Sub
menu menu
Sub menu item
Contrast
Description
icon
icon
Adjusts the contrast between the
foreground and background of the
screen image.
Brightness
ACM
Adjusts the background brightness of the
screen image.
ACM (Adaptive Contrast Management)
ACM On/Off switch, default Off.
Focus
Adjusts picture focus (available in analog
mode only).
Clock
Adjusts the picture clock (available in
analog mode only).
H. Position
V. Position
Warm
Adjusts the horizontal position (available
in analog mode only).
Adjusts the vertical position (available in
analog mode only).
N/A
N/A
Sets the color temperature to warm
white.
Cool
Sets the color temperature to cool white.
Adjusts red intensity.
User/red
User/green
User/blue
Adjusts green intensity.
Adjusts blue intensity.
12
Main
Sub
menu menu
Sub menu item
English
Description
icon
icon
N/A
N/A
N/A
Language selection.
繁體中文
Deutsch
Français
Español
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
Italiano
简体中文
日本語
EMEA version OSD only.
Suomi
Nederlands
Русский
N/A
N/A
N/A
Türkçe
Polski
Português
H. Position
V. Position
OSD Timeout
Analog
Adjusts the horizontal position of the
OSD.
Adjusts the vertical position of the OSD.
Adjusts the OSD timeout.
N/A
N/A
Selects input signal from analog (D-sub).
Digital (only dual- Selects input signal from digital (DVI)
input models)
(only dual-input models).
N/A
N/A
DDC/CI
Turns on/off DDC/CI support.
Information
Shows the resolution, H/V frequency,
input port and serial number for current
input.
N/A
N/A
Reset
Exit
Clears Auto-configuration changes .
Saves user changes and closes the OSD.
13
Troubleshooting
Before sending your LCD monitor for servicing, please check the
troubleshooting list below to see if you can self-diagnose the problem.
VGA mode
Problem
LED status
Blue
Remedy
No picture visible
Using the OSD, adjust brightness and
contrast to maximum or reset to their
default settings.
Off
Check the power switch.
Check if the power cord is properly
connected to the monitor.
Amber
Check if the video signal cable is
properly connected at the back of
monitor.
Check if the computer system is
switched on and in power saving/
standby mode.
Unstable picture
Abnormal picture
Check if the specification of graphics
adapter and monitor is in compliance
which may be causing the input signal
frequency mismatch.
Image is missing, Using the OSD, adjust focus, clock, H-
off-center, too
large or too
small on the
screen.
position and V-position with non-
standard signals.
Check the display setting on your
system. In case of a missing image,
please select another resolution or
vertical refresh rate.
Wait for a few seconds after adjusting
the size of the image before changing
or disconnecting the signal cable or
switching off the monitor.
14
DVI mode
Problem
LED status
Blue
Remedy
No picture visible
Using the OSD, adjust brightness and
contrast to maximum or reset to their
default settings.
Off
Check the power switch.
Check if the AC power cord is properly
connected to the monitor.
Amber
Check if the video signal cable is
properly connected at the back of
monitor.
Check that the computer system is
switched on and in power saving/
standby mode.
|