AT T E580 1 User Manual

ATT-580-1CIB-d2.qxd 1/17/2004 6:12 PM Page 1  
User Manual (Part 2)  
5.8 GHz Expansion  
Handset E580-1  
For use withAT&T models  
E5860 • E5865 • E5900B • E5965C  
ATT-580-1CIB-d2.qxd 1/17/2004 6:12 PM Page 1  
Before you begin  
This cordless telephone operates with  
the maximum power allowed by the  
Federal Communications Commission  
(FCC). Even so, the handset and base  
can communicate over only a certain  
distance — which can vary with the  
locations of the base and handset, the  
weather, and the construction of your  
home or office. For best performance,  
keep the base antenna fully upright.  
If you move out of range during a  
phone conversation, you might hear  
noise or interference. To improve  
reception, move closer to the base.  
If you move out of range without  
pressing OFF, your phone will be left  
“off the hook.” To hang up properly,  
walk back toward the telephone base,  
periodically pressing OFF until the call  
is disconnected.  
If you receive a call while you are  
out of range, the handset might not  
ring — or if it does ring, the call might  
not connect when you press PHONE.  
Move closer to the base, then press  
PHONE to answer the call.  
Parts checklist  
Remember to save your sales receipt and original packaging in case you ever need to  
ship your telephone for warranty service. Check to make sure the telephone package  
includes the following:  
Power  
adapter  
Telephone  
handset  
Belt clip  
Batteries  
Handset charger  
1
ATT-580-1CIB-d2.qxd 1/17/2004 6:13 PM Page 2  
Battery installation & charging  
After installation, place the handset in the charger and allow batteries to charge for 12  
hours before use. You can keep batteries charged by returning the handset to the charger  
after each use. When battery power is fully depleted, a full recharge takes about 8 hours.  
1
LOW BATTERY  
REDIAL  
CID LOG  
2:10 PM  
Low battery indicator  
Return handset to charger to recharge  
when this symbol flashes. (Handset  
will beep when battery is low.)  
Press coin into slot on  
base of handset to  
release latch, then  
remove battery cover.  
Insert supplied  
batteries.  
Plug power cord into jack on underside  
of charger, then plug transformer into  
electrical outlet.  
To replace battery cover  
Insert top  
tab first.  
Press down to  
click in place.  
Caution: Use only the supplied  
Place handset in charger to charge  
for 12 hours before first use.  
NiMH battery (80-5461-00-00) or  
AT&T model 2AA NiMH replace-  
ment battery (SKU 26820). Do not  
use alkaline batteries.  
Light remains on while batteries  
are charging.  
2
ATT-580-1CIB-d2.qxd 1/17/2004 6:13 PM Page 3  
Registering the handset  
Before using your new handset, you must register it with  
the base. During registration, you must enter the 15-digit  
ID number of the telephone base. To find this number, go  
to the base, press MENU, scroll down to select DISPLAY  
BASE ID, then press OK.  
MENU  
The handset provided with your telephone is automatically  
registered as Handset 1. Additional handsets will be  
assigned numbers in the order they are registered (2, 3, 4,  
etc.) up to a maximum of eight.  
CALLS LOG  
BASE SETTINGS  
DISPLAY BASE-ID  
OK  
^
V
CALLS LOG  
BASE SETTINGS  
DISPLAY BASE-ID  
OK  
^
V
Handset 1  
Handset 2  
Handset 3  
123456789012345  
OK  
3
ATT-580-1CIB-d2.qxd 1/17/2004 6:14 PM Page 4  
Belt clip & optional headset  
Install belt clip as shown below if desired.  
For hands-free telephone conversations, you can use any industry standard 2.5 mm  
headset (purchased separately). For best results use an AT&T 2.5 mm headset.  
Snap belt clip into notches on  
side of handset. Rotate and pull  
to remove.  
Plug 2.5 mm headset  
into jack on side of  
handset (beneath  
small rubber cap).  
4
ATT-580-1CIB-d2.qxd 1/17/2004 6:15 PM Page 5  
Quick reference guide  
For complete instructions, please refer to the manual provided with your telephone.  
Up  
Select  
Right  
Left  
Down  
NavKey  
Softkeys  
Press center button to display menus.  
Press NavKey buttons to navigate  
through menus. Press center button to  
select menu item highlighted.  
Press a softkey to select a menu item  
displayed just above the key.  
Off/Cancel  
Phone/Flash  
During a call, press to hang up.  
Press to begin a call, then dial a number.  
While using menus, press to cancel an  
operation, back up to the previous menu,  
or exit the menu display.  
During a call, press to receive an incoming  
call, if Call Waiting is activated.  
Speaker  
Sound Select  
Press to activate handset speaker-  
phone. Press again to switch call back  
to earpiece.  
Press to customize speaker sound for  
clear speakerphone conversations.  
Main menu  
Intercom  
Directory  
Calls Log  
Pictures  
Sounds&Alerts  
Settings  
Sounds & Alerts menu  
Settings menu  
Vibrate  
Ringer Control  
Ringers  
Clock On/Off  
Set Time  
Contrast  
Low Batt Tone Keypad Tone  
Range Tone  
Phone Setup  
Language  
Reset Settings  
5
ATT-580-1CIB-d2.qxd 1/17/2004 6:15 PM Page 6  
Copyright © 2004 Advanced American Telephones. All Rights Reserved.  
AT&T and the Globe Design are trademarks of AT&T Corp.,  
licensed to Advanced American Telephones. Printed in China. Issue 1.2 AT&T 1/19/04.  

HP Hewlett Packard L1940T EM869AA User Manual
HP Hewlett Packard 7540 User Manual
Electrolux 318201432 User Manual
Dell Computer Monitor IN2020MF User Manual
Cisco Systems Cisco MGX 8800 User Manual
Caldera SSK305NG US User Manual
Audiovox VOH1012P User Manual
Asus A8V VM SE User Manual
AOC Computer Monitor 917SW User Manual
AMD SBX 5363 User Manual