AT T E250 User Manual

ATT-250CIB-d1.qxd 12/30/2003 2:02 PM Page 1  
User Manual (Part 2)  
2.4 GHz Expansion  
Handset E250  
For use withAT&T models  
E2555 • E2525 • E2600B  
ATT-250CIB-d1.qxd 12/30/2003 2:02 PM Page 1  
Before you begin  
This cordless telephone operates with  
the maximum power allowed by the  
Federal Communications Commission  
(FCC). Even so, this handset and base  
can communicate over only a certain  
distance — which can vary with the  
locations of the base and handset, the  
weather, and the construction of your  
home or office. For best performance,  
keep the base antenna fully upright.  
If you move out of range during a  
phone conversation, you might hear  
noise or interference. To improve  
reception, move closer to the base.  
If you move out of range without  
pressing OFF, your phone will be left  
“off the hook.” To hang up properly,  
walk back toward the telephone base,  
periodically pressing OFF until the call  
is disconnected.  
If you receive a call while you are  
out of range, the handset might not  
ring — or if it does ring, the call might  
not connect when you press PHONE.  
Move closer to the base, then press  
PHONE to answer the call.  
Parts checklist  
Remember to save your sales receipt and original packaging in case you ever need to  
ship your telephone for warranty service. Check to make sure the telephone package  
includes the following:  
Power  
adapter  
Telephone  
handset  
Belt clip  
Batteries  
Handset charger  
1
ATT-250CIB-d1.qxd 12/30/2003 2:03 PM Page 2  
Battery installation & charging  
Install batteries as shown, then place the handset in the charger for at least 8 hours  
before use. You can keep batteries charged by returning the handset to the charger after  
each use. When battery power is fully depleted, a full recharge takes about 6 hours.  
LOW BATTERY  
REDIAL  
MENU  
MEM  
Low battery indicator  
Return handset to charger to recharge  
when this symbol flashes. (Handset  
will beep when battery is low.)  
Press coin into slot on  
base of handset to  
release latch, then  
remove battery cover  
Insert supplied  
batteries  
Caution: Use only AT&T 2AA  
NiCad or NiMH rechargeable  
batteries. Do not use AA  
alkaline batteries.  
Plug power cord into jack on underside  
of charger, then plug transformer into  
electrical outlet  
To replace battery cover  
Insert top  
tab first  
Press down to  
click in place  
Place handset in charger to  
charge for 8 hours before first use.  
Light remains on while batteries  
are charging.  
2
ATT-250CIB-d1.qxd 12/30/2003 2:03 PM Page 3  
Registering the handset  
Enter base ID, then press OK  
Before using your new handset, you must register it with  
the base. During registration, you must enter the 15-digit  
ID number of the telephone base. To find this number, go  
to the base, press MENU, scroll down to select DISPLAY  
BASE ID, then press OK.  
ENTER BASE ID  
123456789012345  
OK  
<
The handset provided with your telephone is automatically  
registered as Handset 1. Additional handsets will be  
assigned numbers in the order they are registered (2, 3, 4,  
etc.) up to a maximum of eight.  
HANDSET 2  
REDIAL  
MENU  
MEM  
Handset 1  
Handset 2  
Handset 3  
3
ATT-250CIB-d1.qxd 12/30/2003 2:03 PM Page 4  
Belt clip & optional headset  
Install belt clip as shown below if desired.  
For hands-free telephone conversations, you can use any industry standard 2.5 mm  
headset (purchased separately). For best results use an AT&T 2.5 mm headset.  
Snap belt clip into notches on  
side of handset. Rotate and pull  
to remove.  
Plug 2.5 mm headset  
into jack on side of  
handset (beneath  
small rubber cap)  
4
ATT-250CIB-d1.qxd 12/30/2003 2:03 PM Page 5  
Quick reference guide  
For complete instructions, please refer to the manual provided with your telephone.  
Softkeys  
Press a softkey to select a menu item  
displayed just above the key.  
Off/Clear  
During a call, press to hang up.  
Item 1 Item 2 Item 3  
While using menus, press to cancel an  
operation, back up to the previous  
menu, or exit the menu display.  
Phone/Flash  
Press to begin a call, then dial a number.  
Xfer/Intercom  
During a call, press to receive an incoming  
call, if Call Waiting is activated.  
Press to transfer a call or initiate an  
intercom conversation.  
Speaker  
Sound Select  
Press to activate handset speaker-  
phone. Press again to switch call back  
to earpiece.  
Press to customize speaker sound for  
clear speakerphone conversations.  
Screen menus  
Main Menu  
Handset Settings  
Redial Log  
Phonebook  
Calls Log  
Ringer Volume  
Ringer Melody  
Low Batt Tone  
Range Tone  
Keypad Tone  
Contrast  
Play Messages  
Handset Settings  
Set Time  
HANDSET 1  
REDIAL  
MENU  
MEM  
Clock Mode  
Register  
Language  
Menus  
5
ATT-250CIB-d1.qxd 12/30/2003 2:03 PM Page 6  
Copyright © 2003 Advanced American Telephones. All Rights Reserved.  
AT&T and the Globe Design are trademarks of AT&T Corporation,  
licensed to Advanced American Telephones. Printed in China. Issue 1.1 AT&T 12/30/03.  

Hotpoint HW170GIW User Manual
EVGA X58 FTW User Manual
Elmo LM 5011N User Manual
Electrolux SIG 553 User Manual
Compaq 5400 User Manual
Cobra Electronics CP 9135 User Manual
Clarity XLC 3 1 User Manual
Black Box Computer Hardware ServSwitch DKM FX User Manual
Acer AL2216W User Manual
3M ET 355 User Manual