9371_book_1ATT 8/14/01 10:00 AM Page ii
USER’S MANUAL
Part 2
900 MHz Cordless
Telephone/Answering System
with Caller ID/Call Waiting 9371
DRAFT 8/14/01
Please also read
Part 1 — Important
Product Information
AT&T and the globe symbol are registered trademarks of AT&T Corp. licensed to Advanced AmericanTelephones.
9371_book_1ATT 8/14/01 10:00 AM Page iv
CONTENTS
BEFORE YOU BEGIN . . . . . . 1
TELEPHONE MEMORY
About Caller Identification ........... 1
AT THE BASE . . . . . . . . . . . . . 16
Store a Number in
Base Memory ...........................16
Dial a Number in
INSTALLATION . . . . . . . . . 2
Before You Install .......................... 2
Table/Desk Installation...................3
Wall Installation ............................ 5
Base Memory........................... 16
CALLER ID OPERATION . . . 17
About Call History ...................... 17
Review Call History .................... 17
Delete Records from
Call History.............................. 18
Dial a Displayed Number............ 18
Store a Call History Record
TELEPHONE OPERATION
AT THE HANDSET . . . . . . . . . . . 7
Make a Call.................................... 7
Answer a Call ................................ 7
End a Call...................................... 7
Change Channel............................ 7
Redial ............................................ 7
Handset Volume ............................ 7
Flash/Call Waiting......................... 7
Hold .............................................. 7
Intercom ....................................... 7
Handset Ringer Style/Battery Save .. 8
Temporary Tone Dialing................ 8
Headset Jack.................................. 8
Operating Range ........................... 9
Display Screen Message ................ 9
in the Directory....................... 19
Display Screen Messages............ 19
ANSWERING SYSTEM OPERATION
AT THE BASE . . . . . . . . . . . . . . 20
Audible Indicators....................... 20
Set the Clock............................... 20
About Mailboxes......................... 20
About Announcements ............... 20
Record Your Announcement....... 21
Answering System
Feature Setup........................... 22
Feature Summary ........................ 22
Listen to, Save
& Delete Messages................... 23
Call Screening/Intercept............. 24
Record a Memo........................... 24
Message Window Display............ 24
TELEPHONE OPERATION
AT THE BASE . . . . . . . . . . . . . 10
Make,Answer, or End a Call ........ 10
Speaker/Base Ringer Volume ...... 10
Redial .......................................... 10
Hold ............................................ 10
Mute............................................ 10
Flash............................................ 10
Page/Intercom............................. 11
Handset Locator.......................... 11
ANSWERING SYSTEM OPERATION
AT TOUCH TONE PHONE . . . . . . .25
Connect with the
Answering System ................... 25
Voice Menu ................................. 25
Remote Access Commands......... 25
TELEPHONE MEMORY
AT THE HANDSET . . . . . . . . . . 12
One Touch Memory .................... 12
Store a Number in m ................. 12
Dial the m Number.................... 12
Store a Number in the Directory... 13
Edit a Number Stored
BATTERIES . . . . . . . . . . . 27
Charging the Handset
Battery Pack............................. 27
Replacing the Handset
in the Directory....................... 14
Delete a Number Stored in
Battery Pack..............................28
the Directory........................... 15
Dial a Number Stored in
IN CASE OF DIFFICULTY . . 29
the Directory........................... 15
9371_book_1ATT 8/14/01 10:00 AM Page 1
BEFORE YOU BEGIN
About Caller Identification (Caller ID)
This product has a Caller ID with Call Waiting feature that works with
service from your local phone service provider.
Caller ID with Call Waiting lets you see who’s calling before you answer the
phone, even when you’re on another call.
You may need to change your phone service to use this feature. Contact
your phone service provider if:
•
You have both Caller ID and Call Waiting, but as separate services
(you may need combined service)
•
•
You have only Caller ID service, or only Call Waiting service
You don’t subscribe to any Caller ID or Call Waiting services.
You can use this product with regular Caller ID service, and you can use
this product’s other features without subscribing to either Caller ID or
combined Caller ID with Call Waiting service.
There are fees for Caller ID services, and they may not be available in all
areas.
This product can provide information only if both you and the caller are in
areas offering Caller ID service, and if both telephone companies use
compatible equipment.
1
9371_book_1ATT 8/14/01 10:00 AM Page 2
INSTALLATION
Before You Install
1
Choose a location for the base near an electrical outlet and a
telephone jack.
This phone requires a modular telephone jack and a standard electrical
outlet (110v AC) not controlled by a wall switch.
2
Install the handset battery.
a) Remove battery
compartment
cover by pressing
on the
indentation
and sliding
downward.
b) Align two holes in
plug with socket
pins, and snap the
plug into place.
c) Place battery pack
in compartment
with the wires in
the lower left
corner, along the
bottom of the
battery pack.
d) Replace
cover by
sliding it up
into place.
2
9371_book_1ATT 8/14/01 10:00 AM Page 3
INSTALLATION
3
Attach belt clip to the cordless handset (optional).
To attach
To remove
Table/Desk Installation
Standard
electrical outlet
Modular
telephone
jack
1
Connect the telephone line cord.
2
Connect the power cord.
The ANSWER ON/OFF light goes on,
and CL flashes in the Message Window.
Use only the power cord
supplied with this product.
If you need a replacement,
call 1 800 222–3111.
3
9371_book_1ATT 8/14/01 10:00 AM Page 4
INSTALLATION
3
Charge the handset battery.
Place the handset in the base. Charge the battery for at least 16 hours
the first time. After the first charge, the battery is typically fully
charged overnight.
4
5
Check for dial tone.
After the batteries are charged, pick up the handset and press P;
you should hear a dial tone.
Set the dial mode.
If you have touch tone service, the phone is ready to use as soon as
the batteries are charged.
If you have dial pulse (rotary) service, you’ll need to change the dial
mode.
•
•
Press p on the handset to enter programming mode.
Press < or > until the screen displays DIAL MODE:and the
currently selected mode.
•
•
•
Press s. The current setting blinks.
Press > to select TONEor PULSE.
Press s or p, to save the displayed mode.
6
Set the time and date displayed on handset screen.
If you subscribe to Caller ID service, the date and time will be set
automatically with the first incoming call.
If you do not have Caller ID service, you can set the date and time
manually.
•
•
Press p on the handset to enter programming mode.
Press < or > until the screen displays DATE/TIMEand the
current setting.
•
•
•
•
•
•
Press s until the month blinks. Use < or > to change the
month.
Press s to save the new month; the day blinks. Use < or >
to change the day.
Press s to save the new day; the hour blinks. Use < or >
to change the hour.
Press s to save the new hour; the minute setting blinks. Use <
or > to change the minutes.
Press s to save the new minute setting; AMor PMblinks. Use <
or > to switch between AMand PM.
Press s or p to save the new date and time.
4
9371_book_1ATT 8/14/01 10:00 AM Page 5
INSTALLATION
Wall Installation
1
Position the wall mount adapter on the base.
Align tabs on wall
mount adapter with
holes on bottom of
base. Snap wall
mount adapter firmly
into place.
5
9371_book_1ATT 8/14/01 10:00 AM Page 6
INSTALLATION
2
3
Connect the telephone line cord.
Connect the power cord.
The ANSWER ON/OFF light goes on, and CL flashes in the Message
Window.
Use only the power cord supplied with this product. If you
need a replacement, call 1 800 222–3111.
4
Mount the base on the wall.
a) Align holes
on base with
mounting
studs on wall
jack.
b) Place power
cord as shown.
c) Pull base down on
mounting studs until
it locks into place.
5
Follow Steps 3–6 in “Table/Desk Installation.”
6
9371_book_1ATT 8/14/01 10:00 AM Page 7
TELEPHONE OPERATION
AT THE HANDSET
Answer a Call
Press any key
except O.
Handset Volume
While on a call,
adjust volume
of what you hear.
Make a Call
Press P, then
dial the number
Flash/
Call Waiting
Access special
— OR —
telephone company
subscriber services.
Dial the number
(use < to backspace
and correct digits),
then press P to
call.
End a Call
Press O
— OR —
Place handset
in base.
Enter programming
while not on a call
Exit
programming
Hold
Press to put a
call on hold.
Press again to
release hold
— OR —
Lift the handset
of an extension.
Cancel a page
Redial
Press P, then
press r to
call last number dialed
(up to 32 digits).
Change Channel
Switch to a clearer channel
while on a call.
Intercom
1
Press to signal the base
— OR —
Press to answer a page from the base. Then speak with
someone at the base without tying up the phone line.
Press O to disconnect.
2
7
9371_book_1ATT 8/14/01 10:00 AM Page 8
TELEPHONE OPERATION
AT THE HANDSET
Handset Ringer Style/Battery Save
You can select from four different handset ringer styles, or turn the ringer
off and extend the battery life.
1
2
3
4
5
Make sure the handset is off.
Press p to enter programming mode.
Press > until the screen displays RINGER:and the current setting.
Press s; the current setting blinks.
Press > to select 1, 2, 3, 4, or OFF. You will hear a sample
of each ring.
6
Press s or p to choose the displayed ringer setting.
Temporary Tone Dialing
If you have dial pulse (rotary) service, you can change from dial pulse
to touch tone dialing during a call by pressing *. This is useful if you
need to send touch tone signals for access to telephone banking or
long-distance services.
1
2
3
Dial the number.
Press *. Buttons pressed after this send touch tone signals.
After you hang up, the phone automatically returns to
dial pulse (rotary) service.
Headset Jack
You can use this telephone hands-free when
you install any AT&T 2.5 mm headset,
purchased separately.
Plug the headset into the jack located
on the right side of the handset
(under the small rubber flap).
Do not force the connection,
but make sure the plug
fits securely.
8
9371_book_1ATT 8/14/01 10:00 AM Page 9
TELEPHONE OPERATION
AT THE HEADSET
Operating Range
This cordless telephone operates within the maximum power allowed by
the Federal Communications Commission (FCC). Even so, this handset and
base can communicate over only a certain distance — which can vary with
the locations of the base and handset, the weather, and the construction of
your home or office. For best performance, keep the base antenna fully
upright.
If you receive a call while you are out of range, the handset might not
ring — or if it does ring, the call might not connect when you press P.
Move closer to the base, then press P to answer the call.
If you move out of range during a phone conversation, you might
hear noise or interference. To improve reception, move closer to the base.
If you move out of range without pressing O, your phone will be
left“off the hook.” To hang up properly, walk back into range, periodically
pressing O.
Display Screen Messages
Screen Displays:
When:
NO LINE
The base is not connected to the telephone line,
or the line is not working.
RINGING
CONNECTING
PHONE
There is a call coming in.
The handset is waiting for a dial tone.
The handset is in use.
PAGING
The base is paging the handset.
9
9371_book_1ATT 8/14/01 10:00 AM Page 10
TELEPHONE OPERATION
AT THE BASE
Speaker Volume
While on
a call, use to
adjust the volume
of what you hear.
Base Ringer
Volume Switch
Use to adjust how
loudly the base rings.
Flash
Access subscriber
services while
on a call.
Mute
Press M to
prevent your caller
from hearing you
(you can hear your
caller). Press again
to deactivate.
MUTE light is
on when Mute
is activated.
On steadily:
handset or base
speakerphone is in use
Indicates
handset
is in base
Make, Answer,
or End a Call
Flashing quickly:
an extension is in use
Press K. When
calling, use the base
keypad to dial or
enter a memory
Flashing slowly:
a call is on hold
location. SPEAKER
light is on when call
is connected.
Redial
Press to call the last number dialed at
the base (up to 32 digits).
Hold
Press H to put a call on hold. The IN USE light flashes. To return
to the call, press K.
NOTE: When Hold is active, pressing P on handset will also return
you to the call.
10
9371_book_1ATT 8/14/01 10:00 AM Page 11
TELEPHONE OPERATION
AT THE BASE
Page/Intercom
1
Press and release to signal someone at the
handset. A paging tone sounds.
2
When the person at the handset presses
I, the handset and base can communicate
without tying up the phone line.
3
Press again or press o on handset to
disconnect.
Handset Locator
Press to locate the
handset. The handset
will beep for up to
one minute or until
you turn it off by
pressing again or
pressing o on the
handset.
NOTE: When the handset is in use the Page/Intercom
and Handset Locator features are inactive.
11
9371_book_1ATT 8/14/01 10:00 AM Page 12
TELEPHONE MEMORY
AT THE HANDSET
One Touch Memory
You can store one phone
number (up to 16 digits) in
the one touch memory
location.
NOTE: Press O at any
time to exit memory.
Store a Number in m
1
2
3
4
Press p to enter programming mode.
Press < or > until the screen displays SET ONE TOUCH.
Press s. A flashing cursor appears on screen.
Enter the telephone number you want to store. Use < to
backspace and make a correction.
5
Press s or p to store the number in m
Dial the m Number
Press P, then m to dial the one touch memory number.
12
9371_book_1ATT 8/14/01 10:00 AM Page 13
TELEPHONE MEMORY
AT THE HANDSET
This cordless handset can store an additional 50 telephone numbers with
names in the directory, each up to 16 digits long. Entries are stored
alphabetically. For consistency with Caller ID entries, you may wish to
enter last names first.
Note: Press O at any time to exit memory.
Store a Number in the Directory
1
2
3
Press p. The screen displays DIRECTORY.
Press s. The screen displays ENTER NAME.
Using the chart below, enter up to 15 characters for the name
you’re storing with the number. Use < to backspace and make
corrections; use > to advance and add a space.
Presses
Dial Key
1
2
3
4
5
6
1
2
3
4
5
6
7
8
9
0
*
#
1
A
D
G
J
B
E
C
F
2
3
4
5
6
S
8
Z
H
K
N
Q
U
X
I
L
O
R
V
Y
M
P
T
7
9
W
0
*
&
’
,
-
.
#
13
9371_book_1ATT 8/14/01 10:00 AM Page 14
TELEPHONE MEMORY
AT THE HANDSET
4
When you finish entering the name, press s. The screen
displays ENTER NUMBER.
5
Enter the telephone number. Use < to backspace and make
a correction. Press r to store a pause in the dialing
sequence.
6
Press s or p to store your entry. You’ll hear a series
of beeps confirming the entry.
Note: When memory is full the screen displays MEMORY FULL, an error
tone sounds, and you will not be able to store a new number until you
delete a stored number.
Edit a Number Stored in the Directory
1
2
Press > (DIR). The screen displays DIRECTORY.
Press < or > to scroll alphabetically through numbers
stored in the directory
—OR—
Press the dial pad key for the first letter of the entry you
want to edit.
3
When the screen displays the number you want to edit, press s.
Then press > until EDITflashes.
DIAL EDIT ERASE
9735550123
4
5
Press s. The screen displays the name and number. The flashing
cursor appears at the end of the name. Use <, > and the dial
pad keys to edit the name. Press s to move on to edit the
number.
Press s to save the edited information. You’ll hear a series of
beeps confirming the change.
14
9371_book_1ATT 8/14/01 10:00 AM Page 15
TELEPHONE MEMORY
AT THE HANDSET
Delete a Number Stored in the Directory
1
2
Press > (DIR). The screen displays DIRECTORY.
Press < or > to scroll alphabetically through numbers
stored in the directory
—OR—
Press the dial pad key for the first letter of the entry you
want to delete.
3
4
When the screen displays the number you want to delete, press
s. Then press > until ERASEflashes.
DIAL EDIT ERASE
9735550123
Press s. The screen displays ERASE NO YESand the number.
The current choice flashes.
5
6
Press < or > until YESflashes.
Press s. You’ll hear a series of beeps confirming the deletion.
Dial a Number Stored in the Directory
1
2
Press > (DIR). The screen displays DIRECTORY.
Press < or > to scroll alphabetically through numbers
stored in the directory
—OR—
Press the dial pad key for the first letter of the entry you
want to dial.
3
4
When the screen displays the number you want to dial, press s;
DIALflashes.
DIAL EDIT ERASE
9735550123
Press s. The phone automatically dials the number.
15
9371_book_1ATT 8/14/01 10:00 AM Page 16
TELEPHONEMEMORY
ATTHEBASE
You can store 10 telephone numbers (up to 16 digits each) in the base
memory locations (0-9).
Store a Number in Base Memory
1
Press p on the base to enter programming mode.
The SPEAKER light flashes.
2
3
Press M.
Press the dial pad key (0-9) for the location where you want
to store the number.
4
4
Enter the telephone number.
Press p to store the number. You will hear a confirmation
tone.
Dial a Number in Base Memory
1 Press K.
2 Press M and then the memory location (0-9) of the number
you want to dial. The number is dialed automatically.
16
9371_book_1ATT 8/14/01 10:00 AM Page 17
CALLER ID OPERATION
Caller’s name
Indicates repeat call
Caller’s
telephone
number
Position of call in
call history
Date of call
Time of call
About Call History
This phone assigns each incoming call a number from 1 to 50. The most
recent call will have the highest number. When the memory is full, the
oldest call information is deleted to make room for new incoming call
information.
For each call that comes in, the screen displays the following information
between the first and second rings:
•
Your caller’s name (15 letters are sent by your telephone
company)
•
•
•
The caller’s area code and telephone number
The time and date of the call
The position of the call in call history.
If you answer a call before the information appears on the screen, it will
not be in the call history.
Note: Press O at any time to exit call history.
Review Call History
The screen displays call information for about 15 seconds after it has been
received.
1
2
Press < (CID) to view call history.
Use < and > to scroll through records in call history.
17
9371_book_1ATT 8/14/01 10:00 AM Page 18
CALLER ID OPERATION
Delete Records from Call History
Delete a Specific Call
1
Locate the record you want to delete from call history.
2
Press s, then press > until ERASEflashes.
ERASE
DIAL PGM
973-555-0123
5/01 5:40PM CALL28
3
Press s. The screen displays ERASE NO YES ALLand
the phone number. The current choice flashes.
4
5
Press > until YESflashes.
Press s. You’ll hear a confirmation tone.
Delete All Calls
1
While viewing call history, press s, then press >
until ERASE flashes.
DIAL PGM ERASE
973-555-0123
5/01 5:40PM CALL28
2
3
Press s. The screen displays ERASE NO YES ALLand
the phone number. The current choice flashes.
Press > until ALLflashes, then press s. The screen displays
ERASE ALL NO YES. The current choice flashes.
4
5
Press > until YESflashes.
Press s. You’ll hear a confirmation tone.
Note: You can delete all calls only after all records in call history have
been reviewed.
Dial a Displayed Number
1
2
Locate the record in call history that you want to dial.
If you wish to change how the number is dialed, press #.
The screen displays any alternate dialing sequences available
for this call (area code + number; 1 + area code + number;
1+ number; number only).
3
4
Press s; DIALflashes.
DIAL PGM ERASE
973-555-0123
5/01 5:40PM CALL28
Press s. The phone dials the number
18
9371_book_1ATT 8/14/01 10:00 AM Page 19
CALLER ID OPERATION
Store a Call History Record in the Directory
1
2
Locate the record in call history you want to store in the directory.
If you wish to change how the number is stored, press #.
The screen displays any alternate dialing sequences available
for this call (area code + number; 1 + area code + number;
1+ number; number only).
3
4
Press s, then press > until PGMflashes.
PGM
DIAL
ERASE
973-555-0123
5/01 5:40PM CALL28
Press s three times to store the call record in memory.
You’ll hear a confirmation tone.
Display Screen Messages
Screen Displays:
BLOCKED NAME
BLOCKED CALLER
When:
The other party is blocking name information.
The other party is blocking name and number
information.
UNKNOWN NAME
Your phone company is unable to receive
information about this caller’s name.
UNKNOWN CALLER
Your phone company is unable to receive
information about this caller’s name and number.
EXTENSION IN USE An extension phone on this line is being used, so
call information cannot be received.
19
9371_book_1ATT 8/14/01 10:00 AM Page 20
ANSWERING SYSTEM OPERATION
AT THE BASE
Audible Indicators
This system gives you voice prompts for feature operations and voice
confirmations when you press a button or complete an operation.
Set the Clock
1
2
3
4
5
With answering system on, press U until the system
announces,“Change clock.”
Press S until the system announces the correct day, then
press t.
Press S until the system announces the correct hour, then
press t.
Press S until the system announces the correct minutes, then
press t. The system announces the current clock setting.
Press an MBOX/STOP button to exit programming.
About Mailboxes
This answering system has three voice mailboxes. Callers using a touch
tone phone can select the mailbox in which their messages will be recorded
by pressing * 1, * 2, or * 3 while the system plays the outgoing
announcement. All other messages will be recorded in Mailbox 1.
About Announcements
•
You can record up to two different announcements — one for normal
answering and one for when you’ve set the system to play the
announcement only.
•
Use normal answering when you want the system to record callers’
messages. Use Announce Only when you want to give information to
callers without accepting messages.
•
•
If you choose not to record an announcement, the system answers with
a pre-recorded announcement.
The normal answering pre-recorded announcement says: “Hello. Please
leave a message after the tone.” The Announce Only pre-recorded
announcement says: “We’re sorry, messages to this number cannot
be accepted.”
•
By setting Announce Only to on or off, you decide which
announcement your callers will hear when the system answers a call
(the system comes set for normal answering, with Announce Only
turned off). See“Change Announce Only”on page 22 to change your
announcement selection.
20
9371_book_1ATT 8/14/01 10:00 AM Page 21
ANSWERING SYSTEM OPERATION
AT THE BASE
Record outgoing
announcement
Enter Answering System
feature setup and
choose a feature to set
Select a
feature setting
Turn
Answering
System on
or off
Confirm/review
feature setting
Delete outgoing
announcement,
messages
Record Your Announcement
NOTE: If you have assigned different mailboxes to different people, be
sure to tell callers in your announcement to press * 1, * 2, or * 3
while the announcement is playing to leave a message in the appropriate
mailbox. Remember to leave a few seconds blank at the end of your
recorded announcement to allow callers time to select a mailbox.
1
2
Press U until you hear “Change announcement.”
Press /. After you hear “Now recording” followed by a
beep, speak toward the base to record an announcement up to
90 seconds long.
NOTE: You may wish to leave several seconds of blank time at the end
of your recorded announcement to allow callers enough time to select
a mailbox.
3
Press any MBOX/STOP button to stop recording. The system plays
back your recorded message.
To review your announcement at any time:
1
2
Press U until you hear “Change announcement.”
Press any MBOX/STOP button.
To delete your announcement:
Press D during announcement playback. You will hear
“Announcement deleted.” The system will use the pre-recorded
announcement until you record a new one.
21
9371_book_1ATT 8/14/01 10:00 AM Page 22
ANSWERING SYSTEM OPERATION
AT THE BASE
Answering System Feature Setup
You can set up one feature at a time, or you can set up a feature and then
move on to set up another feature.
1
2
Make sure the answering system is on.
Press and release U until you hear the system announce the
feature you want to set. Refer to the“Feature Summary” below for a
description of the features and your choices.
3
4
Press S to hear the feature’s settings.
Press t to confirm your selection.
Feature Summary
Default settings indicated by .
*
System announces:
Description/directions:
“Change remote access code” Set the remote access code you will use
19
to access features and functions of the
answering system from a touch tone phone.
*
“Change clock”
Set the clock: After you set the day, repeat
Steps 3 and 4 in“Answering System
Feature Setup”to set hours and minutes.
“Change message alert”
When Message Alert is turned on, the base
beeps once every 10 seconds when new
messages have been received.
Off
*
On
“Change announce only”
When you turn Announce Only on, callers
hear your announcement,but cannot
leave a message.
Off
*
On
“Change call screening”
Turn call screening on or off.
On
*
Off
“Change number of rings”
Choose how many times the phone will
ring before the system answers a call.
With Toll Saver active, the system answers
after two rings when you have new
messages and after four rings when you
have no new messages.
2
4
6
*
Toll Saver
NOTE: Exit Feature Setup at any time by pressing an MBOX/STOP button.
22
9371_book_1ATT 8/14/01 10:00 AM Page 23
ANSWERING SYSTEM OPERATION
AT THE BASE
Listen to, Save & Delete Messages
The system automatically saves your messages until you delete them,
and can store approximately 15 minutes of messages, memos, and
announcements (up to a maximum of 99 messages).
After playing a message, the system announces the day and time it was
received. While the message plays, the Message Window displays the
number of the message. After playing the last message in a mailbox, the
system announces“End of messages.” If the system has less than five
minutes of recording time left, it announces remaining time.
Press to repeat a
message; hold to
slow down playback.
Message
Window
Adjust Playback
Volume
System
beeps
three times
at highest
or lowest
setting.
Press to
skip to the
next message;
hold to speed
up playback.
Delete Messages
• Press to delete the message that’s
playing.
Play Messages
• Hold, then press
an MBOX/STOP button to delete
all messages in that mailbox.
Press to play messages
in a mailbox. Press
again to stop playback.
• You cannot delete a message until
it’s been reviewed; deleted
messages cannot be recovered.
23
9371_book_1ATT 8/14/01 10:00 AM Page 24
ANSWERING SYSTEM OPERATION
AT THE BASE
Call Screening/Intercept
1
Make sure the answering system is on and call screening is turned
on (see“Change call screening”on page 22). Adjust the message
playback volume.
2
3
4
Adjust the message so you can hear the caller’s message.
If you decide to take the call, press P on the handset.
If you pick up an extension phone during the announcement and the
announcement does not stop right away,press and release the
telephone switchhook.
Record a Memo
You can record a memo up to four minutes long to store as an incoming message.
1
2
Press and release /.
Press an MBOX/STOP button to select a mailbox for the memo.
After the beep, speak toward the microphone. The Message
Window displays the length of your memo.
3
To stop recording, press the MBOX/STOP button again.
Display:
When:
0
No new messages in any mailbox
–
1
98, flashing
Total number of messages in all mailboxes
Memory is full, or total number of messages is 99
Duration of announcement or memo recording
Length of recording is more than 99 seconds
Current message number during message playback
Current Remote Access Code while setting
Announce Only mode
–
0
99 ↔
F
Counting 1 to 99
99, flashing
–
1
99
–
00 99
A
ON or OFF, steady for Displayed when any setting is changed from
one second
CL ↔ normal display
– –
on or off
Clock needs to be set
System is answering a call or is in remote operation
System is in programming mode or initializing
– – , flashing
24
9371_book_1ATT 8/14/01 10:00 AM Page 25
ANSWERING SYSTEM OPERATION
AT TOUCH TONE PHONE
Connect with the Answering System
You can access many features of this system remotely from a touch tone
phone.
1
2
Dial your telephone number.
When the system answers, press #, then enter your
Remote Access Code (preset to 19). The system beeps once.
3
4
Within two seconds, enter a remote command (see“Remote Access
Commands”).
Press * 0 to exit remote operation.
Voice Menu
The system has voice prompts to help you with remote operation. Press
* 5 to hear the menu while remotely connected to the answering system.
Remote Access Commands
Function:
Command:
Play messages in
a mailbox
Press #, then the appropriate mailbox
number (1, 2, or 3). The system plays
new messages. If there are no new
messages, the system plays old messages.
Repeat a message
Skip a message
Press # 4 while message is playing;
each press backs up another message.
Press # 6 while message is playing;
each press advances another message.
Stop
Press # 5.
Save messages
Delete message
Review announcement
Hang up.
Press # 9 while message is playing.
Press # 7; system plays announcement,
then beeps.
Record announcement
Press * 7; after beep, record
announcement, press # 5 to stop.
System plays back announcement.
25
9371_book_1ATT 8/14/01 10:00 AM Page 26
ANSWERING SYSTEM OPERATION
AT TOUCH TONE PHONE
Remote Access Commands (continued)
Function:
Command:
Record memo
Press * 8; then mailbox number where
you want memo recorded; speak after
beep; press # 5 to exit.
End remote access call
Turn system off
Press * 0.
Press # 0; the system announces,
“Machine off.” Press # 0 again to turn
the system back on.
Turn system on
When system is off, it answers after 10
rings and announces, “Please enter your
remote access code.” Press #, then enter
your remote access code.
NOTE: The remote access call will automatically end if 20 seconds
go by with no key being pressed (other than when recording or playing
messages or announcements).
26
9371_book_1ATT 8/14/01 10:00 AM Page 27
BATTERIES
Charging the Handset Battery Pack
This battery should remain charged up to six days with the ringer turned
on and up to 12 days with the ringer off. A fully charged battery provides
an average talk time of about five hours.
The battery pack needs charging when:
•
•
•
A new battery is installed in the handset.
The phone beeps once every five seconds.
The screen displays BATTERY LOWand the low battery icon.
Place the handset in the base so the CHARGING light turns on. The battery
pack is typically fully charged in eight hours.
You can keep the battery fully charged by returning the handset to the
base after each use.
If you repeatedly get a low battery indicator, even after charging
overnight, the battery should be replaced.
CAUTION: To reduce the risk of fire or injury to persons or
damage to the telephone, read and follow these instructions
carefully:
•
•
Use only Replacement Battery 3301 (SKU# 91076).
Do not dispose of the battery in a fire. The cell might explode.
Check with local codes for special disposal instructions.
Do not open or mutilate the battery. Released electrolyte is
corrosive and may cause damage to the eyes or skin. It may be
toxic if swallowed.
Exercise care in handling batteries in order not to short the battery
with conducting materials such as rings, bracelets, and keys. The
battery or conductor may overheat and cause harm.
Charge the battery provided with or identified for use with this
product only in accordance with the instructions and limitations
specified in this manual.
•
•
•
•
Observe proper polarity orientation between the battery and
battery charger.
27
9371_book_1ATT 8/14/01 10:00 AM Page 28
BATTERIES
Replacing the Handset Battery Pack
1
Remove the battery compartment cover on the handset by
pressing on the indentation and sliding the cover downward.
2
3
Lift out the old battery pack and disconnect.
Align the two holes in the new battery pack’s plug with the
socket pins, and snap the plug into place. Place the battery pack in the
compartment with the wires in the lower left corner, along the bottom
of the battery pack.
4
5
Replace the cover by sliding it up into place.
The new battery pack must be charged before using the phone.
Place the handset in the base and allow it to charge for at least
16 hours the first charge. The telephone might operate before that, but
for best performance, let the battery pack charge fully.
28
9371_book_1ATT 8/14/01 10:00 AM Page 29
IN CASE OF DIFFICULTY
If you have difficulty operating this phone, try the suggestions below.
1 800 222–3111. Please retain your receipt as your proof of purchase.
If the phone doesn’t work at all, check these items first:
•
Make sure the AC adapter is plugged into an outlet not controlled by a
wall switch.
•
Make sure the telephone line cord is plugged firmly into the base unit
and the modular jack.
•
•
Make sure the base antenna is fully upright.
If the handset does not beep when you press P, the battery might
need charging.
•
•
Make sure the battery pack is installed correctly.
If you have dial pulse (rotary) service on your phone line, make sure
the dial mode is set to dial pulse (see INSTALLATION).
If the above suggestions don’t solve the problem, try re-initializing
the handset and base:
1
2
3
4
5
6
Disconnect the power to the base.
Remove the handset battery pack.
Wait a few minutes.
Connect the power to the base.
Insert the handset battery pack.
Put the handset in the base to re-initialize.
If you hear a two-beep signal when you try to use the handset:
•
•
You might be out of range. Move closer to the base and try again.
If moving closer to the base doesn’t help, try following the directions
above for re-initializing the handset and base.
If the phone does not ring when you receive a call:
•
Make sure the handset ringer is on.
•
Make sure the telephone line cord is connected firmly to the base and
the telephone jack.
•
Make sure the AC adapter is plugged firmly into an outlet not
controlled by a wall switch.
•
•
You might be too far from the base; move closer.
You might have too many extension phones on your telephone line
to allow all of them to ring. Try unplugging some of them.
29
9371_book_1ATT 8/14/01 10:00 AM Page 30
IN CASE OF DIFFICULTY
If you hear noise or interference when using the phone:
•
•
•
Make sure the base antenna is fully upright.
You may be out of range. Move closer to the base.
Press and release C to change to another of the 30 channels
available. If noise is exceptionally loud, move closer to the base before
changing channels.
•
•
•
Household appliances plugged into the same circuit as the base can
sometimes cause interference. Try moving the appliance or the base
to another outlet.
The layout of your home or office might be limiting the operating
range. Try moving the base to another location, preferably on an
upper floor.
If the buttons don’t work, try placing the handset in the base for at
least 15 seconds.
If you hear other calls while using your phone:
•
Press C to change to another channel.
•
Disconnect the base from the modular jack and plug in a corded
telephone. If you still hear other calls, the problem is probably in your
wiring or local service. Call your local telephone service company.
If you lose a call after changing channels:
You were probably almost out of range. Move closer to the base before
changing channels. Before placing another call, set the handset in the
base for at least 15 seconds.
If you are unable to operate special telephone services or other
equipment requiring touch tone signals:
If you have dial pulse (rotary) service, follow the directions under
“Temporary Tone Dialing”in the TELEPHONE OPERATION section of
this manual.
If messages are incomplete:
•
•
•
If a caller leaves a very long message, part of it may be lost when the
system disconnects the call after three minutes.
If the caller pauses for more than seven seconds, the system stops
recording and disconnects the call.
If the system’s memory becomes full during a message, the system
stops recording and disconnects the call.
30
9371_book_1ATT 8/14/01 10:00 AM Page 31
IN CASE OF DIFFICULTY
If you have difficulty hearing messages:
Check the volume setting.
If the system does not answer after the correct number of rings:
•
•
Make sure that the answering system is on.
If Toll Saver is on, the number of rings changes to two when you have
new messages waiting.
•
•
In some cases, the system may be affected by the ringing system used
by the local telephone company.
If the memory is full or the system is off, the system answers after
10 rings.
If CL appears in the Message Window:
You need to reset the answering system clock.
If the system does not respond to commands from a remote touch
tone phone:
•
Make sure you are calling from a touch tone phone. When you dial a
number, you should hear tones. If you hear clicks instead, the phone is
not a touch tone telephone.
•
The answering system may not detect the Remote Access Code while
your announcement is playing. Try waiting until the announcement is
over before entering the code.
•
•
Make sure you enter your Remote Access Code correctly.
There may be noise or interference on the phone line you are using.
Press keys firmly.
If your outgoing announcement isn’t clear:
•
When you record your announcement, make sure you speak in a
normal tone of voice, about nine inches from the base.
Make sure there is no“background”noise (TV, music, etc.) while you
are recording.
•
31
9371_book_1ATT 8/14/01 10:00 AM Page 32
9371_book_1ATT 8/14/01 10:00 AM Page 33
|