ASRock Computer Hardware ASRock ConRoe865PE motherboard User Manual

ConRoe865PE

User Manual

Version 3.1

Published May 2006

Contents

1 Introduction ................................................... ... 5

1.1 Package Contents................................................................ 5

1.2 Specifications ..................................................................... 6

1.3 Motherboard Layout ........................................................... 9

1.4 ASRock 8CH I/O .................................................................. 10

2 Installation ............................................. 11

2.1 Screw Holes ...................................................................... 11

2.2 Pre-installation Precautions ................................................ 11

2.3 CPU Installation ................................................................... 12

2.4 Installation of CPU Fan and Heatsink .................................. 14

2.5 Installation of Memory Modules (DIMM) .............................. 15

2.6 Expansion Slots (PCI and AGP Slots) ................................. 17

2.7 Jumpers Setup ................................................................... 18

2.8 Onboard Headers and Connectors .................................... 19

2.9 Serial ATA (SATA) Hard Disks Installation ........................... 22

2.10 Driver Installation Guide .................................................... 22

2.11 Untied Overclocking Technology......................................... 22

3 BIOS SETUP UTILITY...................................... 23

3.1 Introduction .......................................................................... 23

3.1.1 BIOS Menu Bar ......................................................... 23

3.1.2 Navigation Keys ....................................................... 24

3.2 Main Screen ........................................................................ 24

3.3 Advanced Screen ............................................................... 24

3.3.1 CPU Configuration .................................................... 25

3.3.2 Chipset Configuration............................................... 27

3.3.3 ACPI Configuration ................................................... 28

3.3.4 IDE Configuration ...................................................... 29

3.3.5 PCIPnP Configuration ................................................ 31

3.3.6 Floppy Configuration ................................................ 32

3.3.7 Super IO Configuration............................................. 32

3.3.8 USB Configuration .................................................... 34

3.4 Hardware Health Event Monitoring Screen ........................ 35

3.5 Boot Screen ........................................................................ 36

3.5.1 Boot Settings Configuration ..................................... 36

3.5.2 Boot Device Priority .................................................. 37

3.6 Security Screen .................................................................. 37

3.7 Exit Screen .......................................................................... 38

4 Software Support

4.1 Install Operating System ............................................... 39

4.2 Support CD Information ................................................. 39

4.2.1 Running Support CD ............................................ 39

4.2.2 Drivers Menu ........................................................ 39

4.2.3 Utilities Menu ........................................................ 39

4.2.4 “LGA 775 CPU Installation Live Demo” Program .. 39

4.2.5 Contact Information ............................................. 39

Chapter 1 Introduction

Thank you for purchasing ASRock ConRoe865PE motherboard, a reliable

motherboard produced under ASRock’s consistently stringent quality control. It de-

livers excellent performance with robust design conforming to ASRock’s commit-

ment to quality and endurance.

In this manual, chapter 1 and 2 contain introduction of the motherboard and step-by-

step guide to the hardware installation. Chapter 3 and 4 contain the configuration

guide to BIOS setup and information of the Support CD.

Because the motherboard specifications and the BIOS software might be

updated, the content of this manual will be subject to change without

notice. In case any modifications of this manual occur, the updated

version will be available on ASRock website without further notice. You

may find the latest VGA cards and CPU support lists on ASRock website

as well. ASRock website http://www.asrock.com

1.1 Package Contents

ASRock ConRoe865PE Motherboard

(ATX Form Factor: 12.0-in x 9.0-in, 30.5 cm x 22.9 cm)

ASRock ConRoe865PE Quick Installation Guide

ASRock ConRoe865PE Support CD

(including LGA 775 CPU Installation Live Demo)

One 80-conductor Ultra ATA 66/100 IDE Ribbon Cable

One Ribbon Cable for a 3.5-in Floppy Drive

One Serial ATA (SATA) Data Cable (Optional)

One Serial ATA (SATA) HDD Power Cable (Optional)

One ASRock 8CH I/O Shield

1.2

Platform

CPU

- ATX Form Factor: 12.0-in x 9.0-in, 30.5 cm x 22.9 cm

- LGA 775 for Intel^®Dual Core Pentium^®XE and Pentium^®D /

Pentium^®4 / Celeron^®D, supporting Core^TM2 Duo Desktop

(Conroe), Presler and Cedar Mill processors (in 775-land

LGA package)

- FSB 1066/800/533 MHz (see CAUTION 1)

- Supports Hyper-Threading Technology (see CAUTION 2)

- Supports Untied Overclocking Technology (see CAUTION 3)

- Supports EM64T CPU

Chipset

Memory

- Northbridge: Intel^®865PE / 865G

- Southbridge: Intel^®ICH5

- Dual Channel DDR Memory Technology (see CAUTION 4)

- 4 x DDR DIMM slots

- Support DDR400/333/266 (see CAUTION 5)

- Max. capacity: 4GB

Hybrid Booster

Expansion Slot

- CPU Frequency Stepless Control (see CAUTION 6)

- ASRock U-COP (see CAUTION 7)

- Boot Failure Guard (B.F.G.)

- 5 x PCI slots

- 1 x AGP slot (see CAUTION 8)

Audio

LAN

- Realtek ALC850 7.1 channel audio CODEC

- Realtek PCI LAN 8101L

- Speed: 10/100 Ethernet

- Supports Wake-On-LAN

Rear Panel I/O

ASRock 8CH I/O

- 1 x PS/2 Mouse Port

- 1 x PS/2 Keyboard Port

- 1 x Serial Port: COM1

- 1 x Parallel Port (ECP/EPP Support)

- 4 x Ready-to-Use USB 2.0 Ports

- 1 x RJ-45 LAN Port

- Audio Jack: Side Speaker/Rear Speaker/Central/Bass/

Line in/Front Speaker/Microphone (see CAUTION 9)

Connector

- 2 x Serial ATA 1.5Gb/s connectors

(No Support for RAID and “Hot Plug” functions)

- 2 x ATA100 IDE connectors (support 4 x IDE devices)

- 1 x Floppy connector

- 1 x IR header

- 1 x Game header

- CPU/Chassis FAN connector

- 20 pin ATX power connector

- 4 pin 12V power connector

- CD in header

- Front panel audio connector

- 2 x USB 2.0 headers (support 4 USB 2.0 ports)

(see CAUTION 10)

BIOS Feature

- 4Mb AMI BIOS

- AMI Legal BIOS

- Supports “Plug and Play”

- ACPI 1.1 Compliance Wake Up Events

- Supports jumperfree

- AMBIOS 2.3.1 Support

Support CD

Hardware

Monitor

- Drivers, Utilities, AntiVirus Software (Trial Version)

- CPU Temperature Sensing

- Chassis Temperature Sensing

- CPU Fan Tachometer

- Chassis Fan Tachometer

- CPU Quiet Fan

- Voltage Monitoring: +12V, +5V, +3.3V, Vcore

- Microsoft^®Windows^®98SE / ME / 2000 / XP / XP 64-bit

compliant

Certifications

- FCC, CE, WHQL

CAUTION!

1. To support FSB1066 CPU, please use DDR400 DIMMs (Double Data Rate

400 MHz). Before installing FSB1066 CPU, please make sure that you

have adjusted the jumpers correctly. The default setting of FSB1 is to

short pin1 and pin2. However, if you want this motherboard to support

FSB1066 CPU, please adjust your FSB1 jumper setting, and short pin2

and pin3 (see page 18).

2. About the setting of “Hyper Threading Technology”, please check page 26.

3. This motherboard supports Untied Overclocking Technology. Please read

“Untied Overclocking Technology” on page 22 for details.

4. This motherboard supports Dual Channel Memory Technology. Before you

implement Dual Channel Memory Technology, make sure to read the

installation guide of memory modules on page 15 for proper installation.

5. Please check the table below for the memory support frequency and its

corresponding CPU FSB frequency.

CPU FSB Frequency

Memory Support Frequency

DDR266, DDR333*, DDR400

DDR266, DDR333

800

533

1066

DDR400*

When you use a FSB800-CPU on this motherboard, it will run at

DDR320 if you adopt a DDR333 memory module. Besides, if you

use a FSB1066-CPU on this motherboard, please adopt a DDR400

CL2.5 memory module.

6. Although this motherboard offers stepless control, it is not recommended

to perform over-clocking. Frequencies other than the recommended CPU

bus frequencies may cause the instability of the system or damage the

CPU.

7. While CPU overheat is detected, the system will automatically shutdown.

Before you resume the system, please check if the CPU fan on the

motherboard functions properly and unplug the power cord, then plug it

back again. To improve heat dissipation, remember to spray thermal

grease between the CPU and the heatsink when you install the PC system.

8. Do NOT use a 3.3V AGP card on the AGP slot of this motherboard!

It may cause permanent damage!

9. For microphone input, this motherboard supports both stereo and mono

modes. For audio output, this motherboard supports 2-channel, 4-channel,

6-channel, and 8-channel modes. Please check the table on page 10 for

proper connection.

10. Power Management for USB 2.0 works fine under Microsoft^®Windows^®XP

64-bit / XP SP1 or SP2 / 2000 SP4. It may not work properly under

Microsoft^®Windows^®98 / ME.

1.3 Motherboard Layout

5 6

22.9cm (9.0 in)

PS2

PS2_USB_PWR1

Mouse

ATX12V1

USB 2.0

T: USB2

B: USB3

USB 2.0

T: USB0

B: USB1

Top:

RJ-45

Intel

865PE/865G

Chipset

AGP 8X

1.5V_AGP1

4Mb

BIOS

FSB1

PCI

7.1CH

Intel

ICH5

PCI

ConRoe865PE

PCI

LAN

PCI

RoHS

SATA

CMOS

Battery

CLRCMOS0

SATA1 SATA2

AUDIO

CODEC

USB2.0

USB67

USB45

JR1 JL1

AUDIO1

PANEL

PLED PWRBTN

CD1

HDLED RESET

GAME1

SPEAKER1

IR1

FLOPPY1

23 22

1817 16

PS2_USB_PWR1 Jumper

System Panel Header (PANEL1)

Chassis Speaker Header (SPEAKER 1)

USB 2.0 Header (USB67, Blue)

Infrared Module Header (IR1)

USB 2.0 Header (USB45, Blue)

Floppy Connector (FLOPPY1)

Game Connector (GAME1)

Internal Audio Connector: CD1 (Black)

Front Panel Audio Header (AUDIO1)

JR1 / JL1 Jumpers

ATX 12V Connector (ATX12V1)

775-Pin CPU Socket

North Bridge Controller

2 x 184-pin DDR DIMM Slots

(Dual Channel A: DDR1, DDR3; Blue)

2 x 184-pin DDR DIMM Slots

(Dual Channel B: DDR2, DDR4; Black)

Secondary IDE Connector (IDE2, Black)

Primary IDE Connector (IDE1, Blue)

FSB Select Jumper (FSB1)

PCI Slots (PCI1- 5)

South Bridge Controller

BIOS FWH Chip

Primary Serial ATA Connector (SATA1)

Secondary Serial ATA Connector (SATA2)

Clear CMOS Jumper (CLRCMOS0)

Chassis Fan Connector (CHA_FAN1)

AGP Slot (1.5V_AGP1)

ATX Power Connector (ATXPWR1)

CPU Fan Connector (CPU_FAN1)

1.4

Parallel Port

RJ-45 Port

Microphone (Pink)

USB 2.0 Ports (USB01)

Side Speaker (Gray)

Rear Speaker (Black)

Central / Bass (Orange)

Line In (Light Blue)

10 USB 2.0 Ports (USB23)

11 Serial Port: COM1

12 PS/2 Keyboard Port (Purple)

13 PS/2 Mouse Port (Green)

Front Speaker (Lime)

* If you use 2-channel speaker, please connect the speaker’s plug into “Front Speaker Jack”. See

the table below for connection details in accordance with the type of speaker you use.

TABLE for Audio Output Connection

Audio Output Channels Front Speaker Rear Speaker

Central / Bass

Side Speaker

(No. 7)

(No. 4)

(No. 5)

(No. 3)

1 0

Chapter 2 Installation

ConRoe865PE is an ATX form factor (12.0" x 9.0", 30.5 x 22.9 cm) motherboard.

Before you install the motherboard, study the configuration of your chassis to

ensure that the motherboard fits into it.

Make sure to unplug the power cord before installing or removing the

motherboard. Failure to do so may cause physical injuries to you and

damages to motherboard components.

2.1 Screw Holes

Place screws into the holes indicated by circles to secure the motherboard to the

chassis.

Do not over-tighten the screws! Doing so may damage the motherboard.

2.2 Pre-installation Precautions

Take note of the following precautions before you install motherboard components

or change any motherboard settings.

1. Unplug the power cord from the wall socket before touching any component.

2. To avoid damaging the motherboard components due to static electricity, NEVER

place your motherboard directly on the carpet or the like. Also remember to use

a grounded wrist strap or touch a safety grounded object before you handle

components.

3. Hold components by the edges and do not touch the ICs.

4. Whenever you uninstall any component, place it on a grounded antistatic pad or

in the bag that comes with the component.

Before you install or remove any component, ensure that the power is

switched off or the power cord is detached from the power supply.

Failure to do so may cause severe damage to the motherboard, peripherals,

and/or components.

1 1

2.3 CPU Installation

For the installation of Intel 775-LAND CPU,

please follow the steps below.

775-Pin Socket Overview

Before you insert the 775-LAND CPU into the socket, please check if

the CPU surface is unclean or if there is any bent pin on the socket.

Do not force to insert the CPU into the socket if above situation is

found. Otherwise, the CPU will be seriously damaged.

CPU Marked Corner

Step 1. Open the socket:

Step 1-1. Disengaging the lever by depressing

Lift Lever Up to 90°

down and out on the ^Sh^oo^cko^etk^Mat^ro^kedc^Cle^ora^ner^r

retention tab.

Step 1-2. Rotate the load lever to fully open po-

sition at approximately 135 degrees.

Step 1-3. Rotate the load plate to fully open po-

sition at approximately 100 degrees.

Step 2. Insert the 775-LAND CPU:

Step 2-1. Hold the CPU by the edges where are

marked with black lines.

Step 2-2. Orient the CPU with IHS (Integrated

Heat Sink) up. Locate Pin1 and the two

orientation key notches.

Pin1

alignment key

orientation

key notch

orientation

key notch

775-PinSocket

775-LAND CPU

1 2

For proper inserting, please ensure to match the two orientation key

notches of the CPU with the two alignment keys of the socket.

Step 2-3. Carefully place the CPU into the socket

by using a purely vertical motion.

Step 2-4. Verify that the CPU is within the socket

and properly mated to the orient keys.

Step 3. Remove PnP Cap (Pick and Place Cap):

Use your left hand index finger and thumb to

support the load plate edge, engage PnP cap

with right hand thumb and peel the cap from the

socket while pressing on center of PnP cap to

assist in removal.

1. It is recommended to use the cap tab to handle and avoid kicking

off the PnP cap.

2. This cap must be placed if returning the motherboard for after

service.

Step 4. Close the socket:

Step 4-1. Rotate the load plate onto the IHS.

Step 4-2. While pressing down lightly on load

plate, engage the load lever.

Step 4-3. Secure load lever with load plate tab

under retention tab of load lever.

1 3

2.4

This motherboard is equipped with 775-Pin socket that supports Intel 775-LAND CPU.

Please adopt the type of heatsink and cooling fan compliant with Intel 775-LAND CPU

to dissipate heat. Before you installed the heatsink, you need to spray thermal

interface material between the CPU and the heatsink to improve heat dissipation.

Ensure that the CPU and the heatsink are securely fastened and in good contact with

each other. Then connect the CPU fan to the CPU_FAN connector (CPU_FAN1, see

page 9, No. 29).

For proper installation, please kindly refer to the instruction manuals of

your CPU fan and heatsink.

Below is an example to illustrate the installation of the heatsink for 775-LAND CPU.

Step 1. Apply thermal interface material onto center

of IHS on the socket surface.

Step 2. Place the heatsink onto the socket. Ensure

fan cables are oriented on side closest to the

CPU fan connector on the motherboard

(CPU_FAN1, see page 9, No. 29).

Step 3. Align fasteners with the motherboard

throughholes.

Step 4. Rotate the fastener clockwise, then press

down on fastener caps with thumb to install

and lock. Repeat with remaining fasteners.

If you press down the fasteners without rotating them clockwise,

the heatsink cannot be secured on the motherboard.

Step 5. Connect fan header with the CPU fan

connector on the motherboard.

Step 6. Secure excess cable with tie-wrap to ensure

cable does not interfere with fan operation or

contact other components.

1 4

2.5 Installation of Memory Modules (DIMM)

ConRoe865PE motherboard provides four 184-pin DDR (Double Data Rate) DIMM

slots, and supports Dual Channel Memory Technology. For dual channel configuration,

you always need to install identical (the same brand, speed, size and chip-type)

DDR DIMM pair in the slots of the same color. In other words, you have to install

identical DDR DIMM pair in Dual Channel A (DDR1 and DDR3; Blue slots; see p.9

No. 5) or identical DDR DIMM pair in Dual Channel B (DDR2 and DDR4; Black slots;

see p.9 No. 6), so that Dual Channel Memory Technology can be activated. This

motherboard also allows you to install four DDR DIMMs for dual channel configuration,

and please install identical DDR DIMMs in all four slots. You may refer to the Dual

Channel Memory Configuration Table below.

Dual Channel Memory Configurations

DDR1

DDR2

DDR3

DDR4

(Blue Slot)

Populated

(Black Slot) (Blue Slot)

(Black Slot)

(1)

(2)

(3)*

Populated

* For the configuration (3), please install identical DDR DIMMs in all four slots.

1. If you want to install two memory modules, for optimal compatibility

and reliability, it is recommended to install them in the slots of the

same color. In other words, install them either in the set of blue slots

(DDR1 and DDR3), or in the set of black slots (DDR2 and DDR4).

2. If only one memory module or three memory modules are installed

in the DDR DIMM slots on this motherboard, it is unable to activate

the Dual Channel Memory Technology.

3. If a pair of memory modules is NOT installed in the same Dual

Channel, for example, installing a pair of memory modules in DDR1

and DDR2, it is unable to activate the Dual Channel Memory

Technology.

1 5

Installing a DIMM

Please make sure to disconnect power supply before adding or

removing DIMMs or the system components.

Step 1. Unlock a DIMM slot by pressing the retaining clips outward.

Step 2. Align a DIMM on the slot such that the notch on the DIMM matches the break

on the slot.

notch

break

notch

break

The DIMM only fits in one correct orientation. It will cause permanent

damage to the motherboard and the DIMM if you force the DIMM into the

slot at incorrect orientation.

Step 3. Firmly insert the DIMM into the slot until the retaining clips at both ends fully

snap back in place and the DIMM is properly seated.

1 6

2.6 Expansion Slots (PCI and AGP Slots)

There are 5 PCI slots and 1 AGP slot on ConRoe865PE motherboard.

PCI slots: PCI slots are used to install expansion cards that have the 32-bit PCI

interface.

AGP slot: The AGP slot is used to install a graphics card. The AGP slot has a special

design of clasp that can securely fasten the inserted graphics

card.

Please do NOT use a 3.3V AGP card on the AGP slot of this

motherboard! It may cause permanent damage! For the voltage

information of your AGP card, please check with the AGP card

vendors.

Installing an expansion card

STEP1: Before installing the expansion card, please make sure that the power

supply is switched off or the power cord is unplugged. Please read the

documentation of the expansion card and make necessary hardware

settings for the card before you start the installation.

STEP2: Remove the system unit cover (if your motherboard is already installed in

a chasis).

STEP3: Remove the bracket facing the slot that you intend to use. Keep the screws

for later use.

STEP4: Align the card connector with the slot and press firmly until the card is

completely seated on the slot.

STEP5: Fasten the card to the chassis with screws.

STEP 6: Replace the system cover.

1 7

2.7 Jumpers Setup

The illustration shows how jumpers are

setup. When the jumper cap is placed on

pins, the jumper is “Short”. If no jumper cap

is placed on pins, the jumper is “Open”. The

illustration shows a 3-pin jumper whose pin1

and pin2 are “Short” when jumper cap is

placed on these 2 pins.

Jumper

FSB1

Setting

Description

“NORMAL” (short pin1, pin2)

is the default setting for the

FSB jumper. “1066” (short

pin2, pin3) is the setting for

the over clocking of CPU

frequency.

(see p.9 item 9)

2_3

1_2

FSB 1066MHz

FSB 533MHz

FSB 800MHz

PS2_USB_PWR1

Short pin2, pin3 to enable

+5VSB (standby) for PS/2

or USB wake up events.

1_2

2_3

(see p.9 No. 1)

+5V

+5VSB

Note: To select +5VSB, it requires 2 Amp and higher standby current provided by

power supply.

JR1(see p.9 No. 24)

JL1(see p.9 No. 24)

JR1

JL1

Note: If the jumpers JL1 and JR1 are short, both the front panel and the rear panel

audio connectors can work.

Clear CMOS

(CLRCMOS0, 2-pin jumper)

2-pin jumper

(see p.9 No. 13)

Note: CLRCMOS0 allows you to clear the data in CMOS. The data in CMOS includes

system setup information such as system password, date, time, and system

setup parameters. To clear and reset the system parameters to default setup,

please turn off the computer and unplug the power cord from the power

supply. After waiting for 15 seconds, use a jumper cap to short 2 pins on

CLRCMOS0 for 5 seconds.

1 8

2.8 Onboard Headers and Connectors

Onboard headers and connectors are NOT jumpers. Do NOT place

jumper caps over these headers and connectors. Placing jumper caps

over the headers and connectors will cause permanent damage of the

motherboard!

FDD connector

(33-pin FLOPPY1)

FLOPPY1

Pin1

(see p.9 No. 20)

the red-striped side to Pin1

Note: Make sure the red-striped side of the cable is plugged into Pin1 side of the

connector.

Primary IDE connector (Blue) Secondary IDE connector (Black)

(39-pin IDE1, see p.9 No. 8)

(39-pin IDE2, see p.9 No. 7)

IDE2

IDE1

PIN1

connect the black end

to the IDE devices

80-conductor ATA 66/100 cable

connect the blue end

to the motherboard

Note: If you use only one IDE device on this motherboard, please set the IDE

device as “Master”. Please refer to the instruction of your IDE device vendor

for the details. Besides, to optimize compatibility and performance, please

connect your hard disk drive to the primary IDE connector (IDE1, blue) and

CD-ROM to the secondary IDE connector (IDE2, black).

Serial ATA Connectors

(SATA1: see p.9 No. 11)

These two Serial ATA (SATA)

connectors support SATA data

cables for internal storage

devices. The current SATA

interface allows up to 1.5 Gb/s

data transfer rate.

(SATA2: see p.9 No. 12)

SATA1 SATA2

Serial ATA (SATA)

Data Cable

Either end of the SATA data cable

can be connected to the SATA

hard disk or the SATA connector

on the motherboard.

1 9

Serial ATA (SATA)

Power Cable

Please connect the black end of

SATA power cable to the power

connector on each drive. Then

connect the white end of SATA

power cable to the power

connect to the

powersupply

connect to the SATA HDD

(Optional)

powerconnector

connector of the power supply.

USB_PWR

USB 2.0 Header

(9-pin USB67)

ASRock 8CH I/O accommo-

dates 4 default USB 2.0 ports. If

those USB 2.0 ports on the I/O

panel are not sufficient, this

USB 2.0 header is available to

support 2 additional USB 2.0

ports.

P-6

P+6

GND

DUMMY

(see p.9 No. 17)

GND

P+7

P-7

USB_PWR

USB 2.0 Header

(9-pin USB45)

ASRock 8CH I/O accommo-

dates 4 default USB 2.0 ports. If

those USB 2.0 ports on the I/O

panel are not sufficient, this

USB 2.0 header is available to

support 2 additional USB 2.0

ports.

USB_PWR

P-5

P+5

GND

DUMMY

(see p.9 No. 19)

GND

P+4

P-4

USB_PWR

IRTX

Infrared Module Header

(5-pin IR1)

This header supports an

+5VSB

DUMMY

optional wireless transmitting

and receiving infrared module.

(see p.9 No. 18)

GND

IRRX

Internal Audio Connectors

(4-pin CD1)

This connector allows you

to receive stereo audio input

from sound sources such as

a CD-ROM, DVD-ROM, TV

tuner card, or MPEG card.

CD-L

GND

CD-R

(CD1: see p.9 No. 22)

CD1

Front Panel Audio Header

(8-pin AUDIO1)

This is an interface for front

panel audio cable that allows

convenient connection and

control of audio devices.

GND

BACKOUT-R

BACKOUT-L

(see p.9 No. 23)

AUD-OUT-L

GND

AUD-OUT-R

MIC-POWER

MIC

2 0

PLED+

PLED-

PWRBTN#

GND

System Panel Header

(9-pin PANEL1)

This header accommodates

several system front panel

functions.

(see p.9 No. 15)

DUMMY

RESET#

GND

HDLED-

HDLED+

Chassis Speaker Header

Please connect the chassis

speaker to this header.

SPEAKER

DUMMY

+5V

(4-pin SPEAKER 1)

(see p.9 No. 16)

Chassis Fan Connector

(3-pin CHA_FAN1)

Please connect a chassis fan

cable to this connector and

match the black wire to the

ground pin.

GND

+12V

CHA_FAN_SPEED

(see p.9 No. 14)

CPU Fan Connector

(4-pin CPU_FAN1)

(see p.9 No. 29)

Please connect a CPU fan cable

to this connector and match

the black wire to the ground pin.

GND

+12V

CPU_FAN_SPEED

FAN_SPEED_CONTROL

ATX Power Connector

Please connect an ATX power

supply to this connector.

(20-pinATXPWR1)

(see p.9 No. 28)

+5V

JBB1

JBX

Game Port Connector

(15-pin GAME1)

Connect a Game cable to this

connector if the Game port

bracket is installed.

MIDI_OUT

JBY

JBB2

MIDI_IN

(see p.9 No. 21)

+5V

JAB2

JAY

GND

JAX

JAB1

+5V

ATX 12V Connector

(4-pin ATX12V1)

Please note that it is necessary

to connect a power supply with

ATX 12V plug to this connector

so that it can provides sufficient

power. Failing to do so will cause

the failure to power up.

(see p.9, No. 2)

2 1

2.9

(

)

This motherboard adopts Intel^®ICH5 south bridge chipset that supports Serial ATA

(SATA) hard disks. You may install SATA hard disks on this motherboard for

internal storage devices. This section will guide you to install the SATA hard disks.

STEP1: Install the SATA hard disks into the drive bays of your chassis.

STEP2: Connect the SATA power cable to the SATA hard disk.

STEP3: Connect one end of the SATA data cable to the motherboard’s primary

SATA connector (SATA1).

STEP4: Connect the other end of the SATA data cable to the primary SATA hard

disk. If you just want to install only one SATA HDD, the installation

process is complete at this step. If you want to install two SATA HDDs,

please continue to do the following steps.

STEP5: Connect the SATA power cable to the SATA hard disk.

STEP6: Connect one end of the second SATA data cable to the motherboard’s

secondary SATA connector (SATA2).

STEP7: Connect the other end of the SATA data cable to the secondary SATA hard

disk.

Before you install OS into the SATA hard disk, you need to check and

ensure the configuration of the OnBoard IDE Operate Mode option in

BIOS setup is correct according to the condition of your system. For

the configuration details, please refer to the instruction on page 29.

2.10 Driver Installation Guide

To install the drivers to your system, please insert the support CD to your optical

drive first. Then, the drivers compatible to your system can be auto-detected and

listed on the support CD driver page. Please follow the order from up to bottom

side to install those required drivers. Therefore, the drivers you install can work

properly.

2.11 Untied Overclocking Technology

This motherboard supports Untied Overclocking Technology, which means during

overclocking, FSB enjoys better margin due to fixed AGP / PCI bus. You may set

“CPU Host Frequency” option of BIOS setup to [Auto], which will show you the

actual CPU host frequency in the following item. Therefore, CPU FSB is untied

during overclocking, but AGP / PCI bus is in the fixed mode so that FSB can

operate under a more stable overclocking environment.

2 2

Chapter 3 BIOS SETUP UTILITY

3.1 Introduction

This section explains how to use the BIOS SETUP UTILITY to configure your system.

The BIOS FWH chip on the motherboard stores the BIOS SETUP UTILITY. You may

run the BIOS SETUP UTILITY when you start up the computer. Please press <F2>

during the Power-On-Self-Test (POST) to enter the BIOS SETUP UTILITY, otherwise,

POST will continue with its test routines.

If you wish to enter the BIOS SETUP UTILITY after POST, restart the system by

pressing <Ctl> + <Alt> + <Delete>, or by pressing the reset button on the system

chassis. You may also restart by turning the system off and then back on.

Because the BIOS software is constantly being updated, the

following BIOS setup screens and descriptions are for refer-

ence purpose only, and they may not exactly match what you

see on your screen.

3.1.1 BIOS Menu Bar

The top of the screen has a menu bar with the following selections:

Main

To set up the system time/date information

To set up the advanced BIOS features

To set up the PCI features

Advanced

PCIPnP

Boot

To set up the default system device to locate and load the

Operating System

Security

Chipset

Exit

To set up the security features

To set up the chipset features

To exit the current screen or the BIOS SETUP UTILITY

Use < > key or < > key to choose among the selections on the menu bar,

and then press <Enter> to get into the sub screen.

2 3

3.1.2

Please check the following table for the function description of each navigation

key.

Navigation Key(s)

Function Description

Moves cursor left or right to select Screens

Moves cursor up or down to select items

To change option for the selected items

To bring up the selected screen

+ / -

<Enter>

<F1>

<F9>

<F10>

<ESC>

To display the General Help Screen

To load optimal default values for all the settings

To save changes and exit the BIOS SETUP UTILITY

To jump to the Exit Screen or exit the current screen

3.2 Main Screen

When you enter the BIOS SETUP UTILITY, the Main screen will appear and display

the system overview

BIOS SETUP UTILITY

Advanced

H/W Monitor

Boot

Security

Exit

Main

System Overview

Use [Enter], [TAB]

or [SHIFT-TAB] to

System Time

System Date

select

field.

[14:00:09]

[Fri 05/19/2006]

Use [+] or [-] to

configure system Time.

BIOS Version

Processor Type

: ConRoe865PE BIOS P1.00

: Intel (R) CPU 3.40 GHz

(64bit supported)

Processor Speed : 3400 MHz

Cache Size : 1024KB

Microcode Update : 0F34/17

Select Screen

Select Item

Tab

F10

ESC Exit

Change Field

Select Field

General Help

Load Defaults

Save and Exit

Total Memory

: 512MB

Dual-Channel Memory Mode

: 256MB/166MHz (DDR333)

: None

: 256MB/166MHz (DDR333)

: None

DIMM

System Time [Hour:Minute:Second]

Use this item to specify the system time.

System Date [Day Month/Date/Year]

Use this item to specify the system date.

3.3 Advanced Screen

In this section, you may set the configurations for the following items: CPU

Configuration, Chipset Configuration, ACPI Configuration, IDE Configuration, PCIPnP

Configuration, Floppy Configuration, SuperIO Configuration, and USB Configuration.

2 4

BIOS SETUP UTILITY

H/W Monitor Boot

Security

Exit

Main

Advanced

Configure CPU

Advanced Settings

WARNING : Setting wrong values in below sections

may cause system to malfunction.

CPU Configuration

Chipset Configuration

ACPI Configuration

IDE Configuration

PCIPnP Configuration

Floppy Configuration

SuperIO Configuration

USB Configuration

Select Screen

Select Item

Enter Go to Sub Screen

General Help

Load Defaults

Save and Exit

Exit

F10

ESC

Setting wrong values in this section may cause

the system to malfunction.

3.3.1 CPU Configuration

BIOS SETUP UTILITY

Advanced

Select how to set the

CPU host frequency.

CPU Configuration

CPU Host Frequency

Actual Frequency (MHz)

Boot Failure Guard

Spread Spectrum

[Auto]

[200]

[Enabled]

[Auto]

Ratio Status

Ratio Actual Value

Ratio CMOS Setting

Unlocked (Max :17, Min : 14)

[17]

Select Screen

Select Item

Enhance Halt State

Max CPUID Value Limit

Intel (R) Virtualization tech.

CPU Thermal Throttling

No-Excute Memory Protection

Hyper Threading Technology

Intel (R) SpeedStep(tm) tech.

[Disabled]

F10

ESC

Change Option

General Help

Load Defaults

Save and Exit

Exit

[Enabled]

[Disabled]

[Enabled]

[Auto]

CPU Host Frequency

While entering setup, BIOS auto detects the present CPU host frequency of

this motherboard. The actual CPU host frequency will show in the following

item.

Boot Failure Guard

Enable or disable the feature of Boot Failure Guard.

Spread Spectrum

This item should always be [Auto] for better system stability.

Ratio Status

This is a read-only item, which displays whether the ratio status of this

motherboard is “Locked” or “Unlocked”. If it shows “Unlocked”, you will find

an item Ratio CMOS Setting appears to allow you changing the ratio value

of this motherboard. If it shows “Locked”, then the item Ratio CMOS Set-

ting will be hidden. If you use the ratio value to time the CPU frequency, it will

be equal to the core speed of the installed processor.

2 5

Ratio Actual Value

This is a read-only item, which displays the ratio actual value of this

motherboard.

Ratio CMOS Setting

If the ratio status is unlocked, you will find this item appear to allow you

changing the ratio value of this motherboard.

Enhance Halt State

All processors support the Halt State (C1). The C1 state is supported

through the native processor instructions HLT and MWAIT and requires no

hardware support from the chipset. In the C1 power state, the processor

maintains the context of the system caches.

Max CPUID Value Limit

For Prescott CPU only, some OSes (ex. NT4.0) cannot handle the function

with disable. This should be enabled in order to boot legacy OSes that

cannot support CPUs with extended CPUID functions.

Intel (R) Virtualization tech.

When this option is set to [Enabled], a VMM (Virtual Machine Architecture)

can utilize the additional hardware capabilities provided by Vanderpool

Technology. This option will be hidden if the installed CPU does not support

Intel (R) Virtualization Technology.

CPU Thermal Throttling

You may select [Enabled] to enable P4 CPU internal thermal control mecha-

nism to keep the CPU from overheated.

No-Excute Memory Protection

No-Execution (NX) Memory Protection Technology is an enhancement to the

IA-32 Intel Architecture. An IA-32 processor with “No Execute (NX) Memory

Protection” can prevent data pages from being used by malicious software

to execute code. This option will be hidden if the current CPU does not

support No-Excute Memory Protection.

Hyper Threading Technology

To enable this feature, it requires a computer system with an Intel Pentium^®4

processor that supports Hyper-Threading technology and an operating sys-

tem that includes optimization for this technology, such as Microsoft^®Win-

dows^®XP. Set to [Enabled] if using Microsoft^®Windows^®XP, or Linux kernel

version 2.4.18 or higher. This option will be hidden if the installed CPU does

not support Hyper-Threading technology.

Intel (R) SpeedStep(tm) tech.

Intel (R) SpeedStep(tm) tech. is Intel’s new power saving technology. Proces-

sor can switch between multiple frequency and voltage points to enable

power savings. If you select [Auto], you need to set the “Power Schemes”

as “Portable/Laptop” to enable this function.

2 6

3.3.2

BIOS SETUP UTILITY

Advanced

Chipset Configuration

Options

133MHz (DDR266)

166MHz (DDR333)

200MHz (DDR400)

Auto

Bypass Access

DRAM Frequency

Flexibility Option

Configure DRAM Timing by SPD

DRAM CAS# Latency

DRAM RAS# Precharge

DRAM RAS# to CAS# Delay

DRAM Precharge Delay

DRAM Burst Length

[Off]

[Auto]

[Disabled]

[Auto]

[4]

[8]

[4]

Select Screen

Select Item

+ -

F10

ESC

Change Option

General Help

Load Defaults

Save and Exit

Exit

[PCI / AGP]

[64MB]

Init. Graphic Adapter Priority

Graphics Aperture Size

[Enabled]

[Auto]

OnBoard LAN

OnBoard AC'97 Audio

Bypass Access

This technology can provide users with the function of increasing the sys-

tem performance. The default value is [Disabled]. It will only work when you

use FSB800 CPU and DDR400 DRAM at the same time; otherwise, this option

will be hidden.

DRAM Frequency

If [Auto] is selected, the motherboard will detect the memory module(s)

inserted and assigns appropriate frequency automatically. You may also

select other value as operating frequency: [133MHz (DDR 266)],

[166MHz (DDR 333)], [200MHz (DDR 400)].

Flexibility Option

The default value of this option is [Disabled]. It will allow better tolerance for

memory compatibility when it is set to [Enabled].

Configure DRAM Timing by SPD

Select [Enabled] will configure the following items by the contents in the

SPD (Serial Presence Detect) device.

DRAM CAS# Latency

Use this item to adjust the means of memory accessing. Configuration

options: [Auto], [2.5], [2], and [3].

DRAM RAS# Precharge

This controls the idle clocks after a precharge command is issued.

Configuration options: [4], [3], and [2].

DRAM RAS# to CAS# Delay

This controls the latency between the DRAM active command and the

read / write command. Configuration options: [4], [3], and [2].

DRAM Precharge Delay

This controls the number of DRAM clocks for RAS minimum. Configura-

tion options: [8], [7], [6], and [5].

2 7

DRAM Burst Length

DRAM Burst length can be set as [8] or [4].

Init. Graphic Adapter Priority

This allows you to select [PCI/AGP] and [AGP/PCI] as the initial graphics

adapter priority. The default vaule is [PCI/AGP].

Graphics Aperture Size

It refers to a section of the PCI memory address range used for graphics

memory. It is recommended to leave this field at the default value unless the

installed AGP card’s specifications requires other sizes.

OnBoard LAN

This allows you to enable or disable the “OnBoard LAN” feature.

OnBoard AC’97 Audio

Select [Auto], [Enabled] or [Disabled] for the onboard AC’97 Audio feature.

3.3.3

BIOS SETUP UTILITY

Advanced

ACPI Configuration

Suspend To RAM

Select auto-detect or

disable the STR

feature.

[Disabled]

Restore on AC / Power Loss

Ring-In Power On

PCI Devices Power On

PS / 2 Keyboard Power On

RTC Alarm Power On

[Power Off]

[Disabled]

Select Screen

Select Item

F10

ESC

Change Option

General Help

Load Defaults

Save and Exit

Exit

Restore on AC/Power Loss

Use this item to set the power state after an unexpected AC/power loss. If

[Power Off] is selected, the AC/power remains off when the power

recovers. If [Power On] is selected, the AC/power resumes and the sys-

tem starts to boot up when the power recovers.

Ring-In Power On

Use this item to enable or disable Ring-In signals to turn on the system from

the power-soft-off mode.

PCI Devices Power On

Use this item to enable or disable PCI devices to turn on the system from the

power-soft-off mode.

PS/2 Keyboard Power On

Use this item to enable or disable PS/2 keyboard to turn on the system from

the power-soft-off mode.

2 8

RTC Alarm Power On

Use this item to enable or disable RTC (Real Time Clock) to power on the

system.

3.3.4

BIOS SETUP UTILITY

Advanced

Set [Compatible Mode]

when both Legacy OS

(MS-DOS, Win Me / 98SE)

and SATA device

IDE Configuration

[Enhanced Mode]

[Both]

OnBoard IDE Operate Mode

OnBoard IDE Controller

are used.

Primary IDE Master

Primary IDE Slave

Secondary IDE Master

Secondary IDE Slave

SATA1

[Hard Disk]

Set [Enhanced Mode]

when Native OS

(Win 2000 / XP)

is used.

[Not Detected]

SATA2

Select Screen

Select Item

F10

ESC

Change Option

General Help

Load Defaults

Save and Exit

Exit

OnBoard IDE Operate Mode

Please select [Compatible Mode] when you install legacy OS (Windows

ME / 98SE) into SATA device. If you install legacy OS into IDE HDD while

SATA devices are used, you also need to select [Compatible Mode].

If native OS (Windows 2000 / XP) is installed into SATA device, please

select [Enhanced Mode]. You also need to select [Enhanced Mode]

while native OS is installed into IDE HDD and SATA devices are used.

If you do not install any SATA device, please also select [Enhanced Mode]

no matter you use legacy OS or native OS for the system.

Please note that the following options will be varied depending on the

“OnBoard IDE Operate Mode” ([Compatible Mode] or [Enhanced

Mode]) that you selected.

When [Enhanced Mode] is selected:

OnBoard IDE Controller

You may enable either the primary IDE channel or the secondary IDE channel.

Or you may enable both the primary and the secondary IDE channels by

selecting [Both]. Set to [Disabled] will disable the both. Configuration options:

[Disabled], [Primary], [Secondary], [Both].

When [Compatible Mode] is selected

Combined Mode Option

It allows you to select between [Pri IDE + SATA] and [SATA + Sec IDE]. If

it is set to [Pri IDE + SATA], then the secondary IDE will not work. Likewise,

if it is set to [SATA + Sec IDE], then the primary IDE will not work.

2 9

Because Intel^®ICH5 south bridge only supports four IDE devices

under legacy OS (Windows ME / 98SE), you have to choose either

[Pri IDE + SATA] or [SATA + Sec IDE] when the installed SATA device

is used with legacy OS.

IDE Device Configuration

You may set the IDE configuration for the device that you specify. We will

use the “Primary IDE Master” as the example in the following instruction,

which can be applied to the configurations of “Primary IDE Slave”, “Sec-

ondary IDE Master”, “Secondary IDE Slave”, “SATA1” and “SATA2” as

well.

BIOS SETUP UTILITY

Advanced

Primary IDE Master

Select the type

of device connected

to the system.

Device

Vendor

Size

:Hard Disk

:ST340014A

:40.0 GB

LBA Mode

Block Mode

PIO Mode

Async DMA

Ultra DMA

S.M.A.R.T.

:Supported

:16Sectors

:MultiWord DMA-2

:Ultra DMA-5

:Supported

Type

[Auto]

[Disabled]

Select Screen

Select Item

LBA/Large Mode

Block (Multi-Sector Transfer)

PIO Mode

DMA Mode

S . M . A . R . T .

32Bit Data Transfer

F10

ESC

Change Option

General Help

Load Defaults

Save and Exit

Exit

TYPE

Use this item to configure the type of the IDE device that you specify.

Configuration options: [Not Installed], [Auto], [CD/DVD], and [ARMD].

[Not Installed]: Select [Not Installed] to disable the use of IDE device.

[Auto]: Select [Auto] to automatically detect the hard disk drive.

After selecting the hard disk information into BIOS, use a disk

utility, such as FDISK, to partition and format the new IDE hard

disk drives. This is necessary so that you can write or read

data from the hard disk. Make sure to set the partition of the

Primary IDE hard disk drives to active.

[CD/DVD]: This is used for IDE CD/DVD drives.

[ARMD]: This is used for IDE ARMD (ATAPI Removable Media Device),

such as MO.

LBA/Large Mode

Use this item to select the LBA/Large mode for a hard disk > 512 MB under

DOS and Windows; for Netware and UNIX user, select [Disabled] to

disable the LBA/Large mode.

3 0

Block (Multi-Sector Transfer)

The default value of this item is [Auto]. If this feature is enabled, it will

enhance hard disk performance by reading or writing more data during

each transfer.

PIO Mode

Use this item to set the PIO mode to enhance hard disk performance by

optimizing the hard disk timing.

DMA Mode

DMA capability allows the improved transfer-speed and data-integrity for

compatible IDE devices.

S.M.A.R.T.

Use this item to enable or disable the S.M.A.R.T. (Self-Monitoring, Analysis,

and Reporting Technology) feature. Configuration options: [Disabled], [Auto],

[Enabled].

32-Bit Data Transfer

Use this item to enable 32-bit access to maximize the IDE hard disk data

transfer rate.

3.3.5 PCIPnP Configuration

BIOS SETUP UTILITY

Advanced

Value in units of PCI

PCI / PnP Configuration

clocks for PCI device

latency timer

PCI Latency Timer

PCI IDE BusMaster

[32]

[Enabled]

Select Screen

Select Item

Change Option

General Help

Load Defaults

Save and Exit

Exit

F10

ESC

PCI Latency Timer

The default value is 32. It is recommended to keep the default value unless

the installed PCI expansion cards’ specifications require other settings.

PCI IDE BusMaster

Use this item to enable or disable the PCI IDE BusMaster feature.

3 1

3.3.6

In this section, you may configure the type of your floppy drive.

BIOS SETUP UTILITY

Advanced

Floppy Configuration

Floppy

Select the type of

floppy drive

connected to the

system.

[1.44 MB 3¹"]

Select Screen

Select Item

F10

ESC

Change Option

General Help

Load Defaults

Save and Exit

Exit

3.3.7 Super IO Configuration

BIOS SETUP UTILITY

Advanced

Configure Super IO Chipset

Allow BIOS to Enable

or Disable Floppy

Controller.

[Enabled]

[3F8 / IRQ4]

[Disabled]

[378]

[ECP + EPP]

[1.9]

[DMA3]

[IRQ7]

[Enabled]

[Disabled]

OnBoard Floppy Controller

Serial Port Address

Infrared Port Address

Parallel Port Address

Parallel Port Mode

EPP Version

ECP Mode DMA Channel

Parallel Port IRQ

Onboard Game Port

Onboard MIDI Port

Select Screen

Select Item

Change Option

General Help

Load Defaults

Save and Exit

F10

ESC Exit

OnBoard Floppy Controller

Use this item to enable or disable floppy drive controller.

Serial Port Address

Use this item to set the address for the onboard serial port or disable it.

Configuration options: [Disabled], [3F8 / IRQ4], [2F8 / IRQ3], [3E8 / IRQ4],

[2E8 / IRQ3].

Infrared Port Address

Use this item to set the address for the onboard infrared port or disable it.

Configuration options: [Disabled], [2F8 / IRQ3], and [2E8 / IRQ3].

3 2

Parallel Port Address

Use this item to set the address for the onboard parallel port or disable it.

Configuration options: [Disabled], [378], and [278].

Parallel Port Mode

Use this item to set the operation mode of the parallel port. The default

value is [ECP+EPP]. If this option is set to [ECP+EPP], it will show the EPP

version in the following item, “EPP Version”. Configuration options:

[Normal], [Bi-Directional], and [ECP+EPP].

EPP Version

Use this item to set the EPP version. Configuration options: [1.9]

and [1.7].

ECP Mode DMA Channel

Use this item to set the ECP mode DMA channel. Configuration

options: [DMA0], [DMA1], and [DMA3].

Parallel Port IRQ

Use this item to set the IRQ for the parallel port. Configuration options:

[IRQ5] and [IRQ7].

OnBoard Game Port

Use this item to enable the Game Port or disable it.

OnBoard MIDI Port

Use this itme to select the address for the MIDI Port or disable it. Configura-

tion options: [Disabled], [300], and [330].

3 3

3.3.8

BIOS SETUP UTILITY

Advanced

USB Configuration

To enable or disable

the onboard USB

controllers.

[Enabled]

USB Controller

USB 2.0 Support

Legacy USB Support

[Enabled]

[Disabled]

Select Screen

Select Item

Change Option

General Help

Load Defaults

Save and Exit

F10

ESC Exit

USB Controller

Use this item to enable or disable the use of USB controller.

USB 2.0 Support

Use this item to enable or disable the USB 2.0 support.

Legacy USB Support

Use this item to enable or disable the support to emulate legacy I/O

devices such as mouse, keyboard,... etc. Or you may select [Auto] so

that the system will start to auto-detect; if there is no USB device

connected, “Auto” option will disable the legacy USB support.

3 4

3.4

In this section, it allows you to monitor the status of the hardware on your system,

including the parameters of the CPU temperature, motherboard temperature, CPU fan

speed, chassis fan speed, and the critical voltage.

BIOS SETUP UTILITY

Boot

Security

Exit

Main

Advanced

H/W Monitor

Hardware Health Event Monitoring

CPU Temperature

M / B Temperature

45 C / 98 F

31 C / 87 F

CPU Fan Speed

Chassis Fan Speed

2463 RPM

N / A

Vcore

1.384V

3.306V

5.067V

11.890V

3.30V

5.00V

12.00V

Select Screen

Select Item

General Help

Load Defaults

Save and Exit

Exit

F10

ESC

CPU Quiet Fan

Target CPU Temperature

Tolerance C)

Target Fan Speed

[Enabled]

(

C) [50]

[02]

[Fast]

(

CPU Quiet Fan

This item allows you to identify the temperature of CPU fan. If you set this

option as [Disabled], the CPU fan will operate in full speed. If you set this

option as [Enabled], you will find the items “Target CPU Temperature

(

C)”, “Tolerance ( C)”, and “Minimun Fan Speed” appear to allow you

adjusting them. The default value is [Disabled].

Target CPU Temperature ( C)

The target temperature will be between 45 C and 65 C. The default

value is [50].

Tolerance ( C)

The default value of tolerance is [2], which means the error of the

target CPU temperature will be within 2 C.

Target Fan Speed

Use this option to set the target fan speed. You can freely adjust the

target fan speed according to the target CPU temperature that you

choose. The default value is [Fast]. Configuration options: [Fast], [Middle]

and [Slow].

3 5

3.5

In this section, it will display the available devices on your system for you to config-

ure the boot settings and the boot priority.

BIOS SETUP UTILITY

Main

Advanced

H/W Monitor

Boot

Security

Exit

Boot Settings

Configure Settings

during System Boot.

Boot Settings Configuration

Boot Device Priority

Hard Disk Drives

Removable Drives

CD/DVD Drives

Select Screen

Select Item

Enter Go to Sub Screen

F10

ESC

General Help

Load Defaults

Save and Exit

Exit

3.5.1 Boot Settings Configuration

BIOS SETUP UTILITY

Boot

Boot Settings Configuration

To enable or disable the

boot from network feature.

Boot From Network

Bootup Num-Lock

[Disabled]

[On]

Select Screen

Select Item

+ -

F10

ESC

Change Option

General Help

Load Defaults

Save and Exit

Exit

Boot From Network

Use this item to enable or disable the Boot From Network feature.

Boot Up Num-Lock

If this item is set to [On], it will automatically activate the Numeric Lock

function after boot-up.

3 6

3.5.2

In this section, you may specify the boot sequence from the available devices

in your system.

BIOS SETUP UTILITY

Boot

Specifies the boot

sequence from the

available devices.

Boot Device Priority

[1st FLOPPY DRIVE]

[HDD: PM-MAXTOR 6L08]

[CD / DVD]

1st Boot Device

2nd Boot Device

3rd Boot Device

device enclosed in

parenthesis has been

disabled in the

corresponding type

menu.

Select Screen

Select Item

+ -

F10

Change Option

General Help

Load Defaults

Save and Exit

ESC Exit

Likewise, you may also specify the boot sequence from the available devices

for the hard disk drives, the removable drives, and the CD/DVD drives.

3.6 Security Screen

In this section, you may set or change the supervisor/user password for the system.

For the user password, you may also clear it.

BIOS SETUP UTILITY

Main

Advanced

H/W Monitor

Boot

Security

Exit

Security Settings

Install or Change the

password.

Supervisor Password : Not Installed

User Password : Not Installed

Change Supervisor Password

Change User Password

Clear User Password

Select Screen

Select Item

Enter Change

F10

ESC

General Help

Load Defaults

Save and Exit

Exit

3 7

3.7

BIOS SETUP UTILITY

H/W Monitro Boot

Main

Advanced

Security

Exit

Exit Options

Exit system setup

after saving the

changes.

Save Changes and Exit

Discard Changes and Exit

Discard Changes

F10 key can be used

for this operation.

Load Optimal Defaults

Select Screen

Select Item

Enter Go to Sub Screen

F10

General Help

Load Defaults

Save and Exit

ESC Exit

Save Changes and Exit

When you select this option, it will pop-out the following message, “Save

configuration changes and exit setup?” Select [OK] to save the changes

and exit the BIOS SETUP UTILITY.

Discard Changes and Exit

When you select this option, it will pop-out the following message, “Dis-

card changes and exit setup?” Select [OK] to exit the BIOS SETUP UTILITY

without saving any changes.

Discard Changes

When you select this option, it will pop-out the following message, “Dis-

card changes?” Select [OK] to discard all changes.

Load Optimal Defaults

When you select this option, it will pop-out the following message, “Load

optimal defaults?” Select [OK] to load the default values for all the setup

configurations.

3 8

Chapter 4 Software Support

4.1 Install Operating System

This motherboard supports various Microsoft^®Windows^®operating systems: 98SE

/ ME / 2000 / XP / XP 64-bit. Because motherboard settings and hardware options

vary, use the setup procedures in this chapter for general reference only. Refer to

your OS documentation for more information.

4.2 Support CD Information

The Support CD that came with the motherboard contains necessary drivers and

useful utilities that enhance the motherboard features.

4.2.1 Running The Support CD

To begin using the support CD, insert the CD into your CD-ROM drive. The CD

automatically displays the Main Menu if “AUTORUN” is enabled in your computer.

If the Main Menu did not appear automatically, locate and double click on the

file “ASSETUP.EXE” from the BIN folder in the Support CD to display the menus.

4.2.2 Drivers Menu

The Drivers Menu shows the available devices drivers if the system detects

installed devices. Please install the necessary drivers to activate the devices.

4.2.3 Utilities Menu

The Utilities Menu shows the applications software that the motherboard

supports. Click on a specific item then follow the installation wizard to install it.

4.2.4 “LGA 775 CPU Installation Live Demo” Program

This motherboard is equipped with Intel LGA 775 socket, which is a new CPU

socket interface that Intel has released. Since it has several tiny pins, whcih

are easily to be damaged by improper handling, ASRock sincerely presents

you a clear installation guide through this “LGA 775 CPU Installation Live Demo”.

We hope you may check this live demo program before you start the installa-

tion of LGA 775 CPU in order to reduce the risks of CPU and motherboard

damages caused by any improper handling. To see this Live Demo, you can

run Microsoft^®Media Player^®to play the file. You may find this Live Demo in the

motherboard’s Support CD through the following path:

..\ Live Demo \ PC DIY \ LGA775INST_English.dat

4.2.5 Contact Information

If you need to contact ASRock or want to know more about ASRock, welcome

to visit ASRock’s website at http://www.asrock.com; or you may contact your

dealer for further information.

3 9

HP Hewlett Packard Hewlett Packard Computer Drive D2D4324 G2 User Manual
Hanns G HSG1034 User Manual
Frigidaire FGGC3645KB User Manual
Eizo 531L User Manual
Cypress CYDC064B16 User Manual
Cuisinart TCS 60 User Manual
CDA COOKING HOB HCG 730 User Manual
AT T DECT 6 0 EL52401 User Manual
ASRock Computer Hardware 775DUAL 880PRO User Manual
Abit BX 133 User Manual