TABLE OF CONTENTS
FOR YOUR SAFETY -------------------------------------------------
SAFETY PRECAUTIONS --------------------------------------
SPECIAL NOTES ON LCD MONITORS -------------------
1
2
2
BEFORE YOU OPERATE THE MONITOR ---------------------
FEATURES --------------------------------------------------------
PACKING LIST ---------------------------------------------------
INSTALLATION INSTRUCTIONS --------------------------
CONTROLS AND CONNECTORS --------------------------
ADJUSTING THE VIEWING ANGLE -----------------------
2
2
2
3
4
5
OPERATING INSTRUCTIONS ------------------------------------
GENERAL INSTRUCTIONS ----------------------------------
HOW TO ADJUST A SETTING ------------------------------
6
6
9
ADJUSTING THE PICTURE ---------------------------------- 10-11
PLUG AND PLAY ------------------------------------------------ 12
TECHNICAL SUPPORT(FAQ) ------------------------------------- 13
ERROR MESSAGE & POSSIBLE SOLUTION --------- 14
HOW TO INSTALL INF & ICM FILE --------------------- 15
APPENDIX ------------------------------------------------------------- 16
SPECIFICATIONS ----------------------------------------------- 16-17
FACTORY PRESET TIMING TABLE ---------------------- 18
CONNECTOR PIN ASSIGNMENT ------------------------- 19
英文
PRECAUTIONS
z Do not use the monitor near water, e.g. near a bathtub, washbowl, kitchen
sink, laundry tub, swimming pool or in a wet basement.
z Do not place the monitor on an unstable cart, stand, or table. If the monitor
falls, it can injure a person and cause serious damage to the appliance.
Use only a cart or stand recommended by the manufacturer or sold with
the monitor. If you mount the monitor on a wall or shelf, use a mounting kit
approved by the manufacturer and follow the kit instructions.
z Slots and openings in the back and bottom of the cabinet are provided for
ventilation. To ensure reliable operation of the monitor and to protect it
from overheating, be sure these openings are not blocked or covered. Do
not place the monitor on a bed, sofa, rug, or similar surface. Do not place
the monitor near or over a radiator or heat register. Do not place the
monitor in a bookcase or cabinet unless proper ventilation is provided.
z The monitor should be operated only from the type of power source
indicated on the label. If you are not sure of the type of power supplied to
your home, consult your dealer or local power company.
z The monitor is equipped with a three-pronged grounded plug, a plug with a
third (grounding) pin. This plug will fit only into a grounded power outlet as
a safety feature. If your outlet does not accommodate the three-wire plug,
have an electrician install the correct outlet, or use an adapter to ground
the appliance safely. Do not defeat the safety purpose of the grounded
plug.
z Unplug the unit during a lightening storm or when it will not be used for
long period of time. This will protect the monitor from damage due to
power surges.
z Do not overload power strips and extension cords. Overloading can result
in fire or electric shock.
z Never push any object into the slot on the monitor cabinet. It could short
circuit parts causing a fire or electric shock. Never spill liquids on the
monitor.
z Do not attempt to service the monitor by yourself; opening or removing
covers can expose you to dangerous voltages and other hazards. Please
refer all servicing to qualified service personnel.
z To ensure satisfactory operation, use the monitor only with UL listed
computers which have appropriate configured receptacles marked
between 100 - 240V AC, Min. 5A.
z The wall socket shall be installed near the equipment and shall be easily
accessible.
英文
2
SPECIAL NOTES ON LCD MONITORS
The following symptoms are normal with LCD monitor and do not indicate a
problem.
NOTES
•
Due to the nature of the fluorescent light, the screen may flicker during
initial use. Turn off the Power Switch and then turn it on again to make
sure the flicker disappears.
•
•
You may find slightly uneven brightness on the screen depending on the
desktop pattern you use.
The LCD screen has effective pixels of 99.99% or more. It may include
blemishes of 0.01% or less such as a missing pixel or a pixel lit all of the
time.
•
Due to the nature of the LCD screen, an afterimage of the previous screen
may remain after switching the image, when the same image is displayed
for hours. In this case, the screen is recovered slowly by changing the
image or turning off the Power Switch for hours.
• When the screen becomes black or flashing, or cannot illuminate any more,
contact your dealer or service center to replace parts. Don’t repair the
screen by yourself!
BEFORE YOU OPERATE THE MONITOR
FEATURES
•
•
43.2cm(17”) TFT Color LCD Monitor
Crisp, Clear Display for Windows
• Recommened Resolutions: 1280 X 1024 @60Hz
•
•
•
EPA ENERGY STAR®
Ergonomic Design
Space Saving, Compact Case Design
PACKAGE LIST
The product package should include the following items:
1. LCD Monitor
2. Owner's Manual
3. Power Cord
4. Signal Cable
5. Driver-Disk
英文
3
INSTALLATION INSTRUCTIONS
SWIVEL BASE
Install
Remove
Figure 1 Installing and Removing the Swivel Base
POWERCORD
Power Source:
1. Make sure that the power cord is the correct type required in your area.
2. This LCD monitor has an Internal universal power supply that allows
operation in either 100/120V AC or 220/240V AC voltage area (No user
adjustment is required.)
3. Connect the power cord into your LCD monitor’s power input socket, and
then plug the other end into a 3-pin AC power outlet. The power cord may
be connected to either a wall power outlet or the power outlet socket on
your PC, depending on the type of power cord supplied with your LCD
monitor.
NOTES
A certified power supply cord has to be used with this equipment. The relevant
national installation and/or equipment regulations shall be considered. A
certified power supply cord not lighter than ordinary polyvinyl chloride flexible
cord according to IEC 60227 (designation H05VV-F 3G 0.75mm2 or
H05VVH2-F2 3G 0.75mm2) shall be used. Alternative a flexible cord be of
synthetic rubber according to IEC 60245 (designation H05RR-F 3G 0.75mm2)
shall be used.
英文
4
CONTROLS AND CONNECTORS
SIGNAL CABLE
Connecting the Signal Cable: Plug the Signal Cable one end to LCD
monitor’s “ DSUB-Input” socket , the other end to the computer's VGA port
and tighten the two screws on the cable connector.
Connecting the Power Cord: Plug the AC-power cord one end to LCD
monitor’s AC input socket , the other end to Wall outlet.
Caution: If the AC outlet is not grounded (with three holes), install the proper
grounding adapter (not supplied).
Figure 2 Connecting Cables
1. VGA input
2. AC Input socket
英文
5
ADJUSTING THE VIEWING ANGLE
•
•
•
For optimal viewing it is recommended to look at the full face of the
monitor, then adjust the monitor’s angle to your own preference.
Hold the stand so you do not topple the monitor when you change the
monitor’s angle.
You are able to adjust the monitor’s angle from -5° to 20°.
Figure 3
NOTES
•
•
Do not touch the LCD screen when you change the angle. It may cause
damage or break the LCD screen.
Careful attention is required not to catch your fingers or hands when you
change the angle.
英文
6
OPERATING INSTRUCTIONS
GENERAL INSTRUCTIONS
Press the power button to turn the monitor on or off. The other control buttons
are located at front panel of the monitor (See Figure 4). By changing these
settings, the picture can be adjusted to your personal preferences.
•
•
•
The power cord should be connected.
Connect the video cable from the monitor to the video card.
Press the power button to turn on the monitor position. The power indicator
will light up.
Figure 4
External Control Button
EXTERNAL CONTROLS
1. Auto Adjust button / Exit
3. Contrast
5. Power Button
2. Brightness
4. MENU / ENTER
6. LED
英文
7
FRONT PANEL CONTROL
• Power Button:
Press this button to switch ON/OFF of monitor’s power.
• MENU / ENTER :
Active OSD menu or function adjust confirm or Exit OSD menu when in
Brightness/Contrast OSD status.
• Contrast
/
:
Adjust contrast or function adjust.
• Brightness
/
:
Adjust brightness or function adjust.
• Auto Adjust button / Exit:
1. When OSD menu is in active status, this button will act as EXIT-KEY
(EXIT OSD menu).
2. When OSD menu is in off status, press this button over 2 seconds to
activate the Auto Adjustment function.The Auto Adjustment function is
used to set the HPos, VPos, Clock and Focus.
• Power Indicator:
Green
Orange
—
—
Power On mode.
Off mode.
• OSD Lock Function:
To lock the OSD, press and hold the MENU button while the monitor is off
and then press power button to turn the monitor on. To un-lock the OSD -
press and hold the MENU button while the monitor is off and then press
power button to turn the monitor on.
英文
8
NOTES
•
Do not install the monitor in a location near heat sources such as
radiators or air ducts, or in a place subject to direct sunlight, or excessive
dust or mechanical vibration or shock.
•
•
•
•
Save the original shipping carton and packing materials, as they will come
in handy if you ever have to ship your monitor.
For maximum protection, repackage your monitor as it was originally
packed at the factory.
To maintain the cleanness of your LCD display, wipe it periodically with
clean and soft cloth. The screen may be damaged by any liquid splash.
To keep the monitor looking new, periodically clean it with a soft cloth.
Stubborn stains may be removed with a cloth lightly dampened with a
mild detergent solution. Never use strong solvents such as thinner,
benzene, or abrasive cleaners, since these will damage the cabinet. As a
safety precaution, always unplug the monitor before cleaning it.
HOW TO ADJUST A SETTING
1. Press the MENU-button to activate the OSD window .
2. Press
function is highlighted, press the MENU-button to activate it. If the
function selected has a sub-menu, press or again to navigate
or
to navigate through the functions. Once the desired
through the sub-menu functions. Once the desired function is highlighted,
press MENU-button to activate it.
3. Press
or
to change the settings of the selected function.
4. To exit and save, select the exit function. If you want to adjust any other
function, repeat steps 2-3.
Figure 5 The OSD Message
英文
9
ADJUSTING THE PICTURE
The descriptions for function control LEDS
Main
Menu
Item
Main
Menu
Icon
Sub
Menu
Icon
Sub
Menu Item
Description
Luminance
Contrast
Brightness
Focus
Contrast from Digital-register.
Backlight Adjustment
Image
Setup
Adjust Picture Phase to reduce
Horizontal-Line noise
Clock
Adjust picture Clock to reduce
Vertical-Line noise.
Image
Position
H. Position
V. Position
Adjust the horizontal position of the
picture.
Adjust the verticalposition of the
picture.
Color
Temp.
Warm
N/A Recall Warm Color Temperature
from EEPROM.
Cool
N/A Recall Cool Color Temperature from
EEPROM.
User / Red
Red Gain from Digital-register.
Green Gain Digital-register.
Blue Gain from Digital-register.
User /
Green
User / Blue
英文
10
Main
Menu
Item
Main
Menu
Icon
Sub
Menu
Item
Sub
Menu
Icon
Description
Auto
Config
Yes
N/A Auto Adjust the H/V Position,
Focus and Clock of picture.
No
N/A Do not execute Auto Config, return
to main menu.
OSD Setup
H. Position
Adjust the horizontal position of the
OSD.
V. Position
Adjust the verticalposition of the
OSD.
OSD
Adjust the OSD timeout.
Timeout
Language
Language
N/A Set OSD language
Information
Reset
Information
Yes
N/A Show the resolution, H/V frequency
and input port of current input
timing.
N/A Clear each old status of Auto-
configuration and set the color
temperature to Cool.
No
N/A Do not execute reset, return to
main menu.
Exit
N/A
N/A Exit OSD
英文
11
PLUG AND PLAY
Plug & Play DDC2B Feature
This monitor is equipped with VESA DDC2B capabilities according to the
VESA DDC STANDARD. It allows the monitor to inform the host system of its
identity and, depending on the level of DDC used, communicate additional
information about its display capabilities.
The DDC2B is a bidirectional data channel based on the I²C protocol. The
host can request EDID information over the DDC2B channel.
THIS MONITOR WILL APPEAR TO BE NON-FUNCTIONAL IF THERE IS
NO VIDEO INPUT SIGNAL. IN ORDER FOR THIS MONITOR TO OPERATE
PROPERLY, THERE MUST BE A VIDEO INPUT SIGNAL.
This monitor meets the Green monitor standards as set by the Video
Electronics Standards Association (VESA) and/or the United States
Environmental Protection Agency (EPA) and The Swedish Confederation
Employees (NUTEK). This feature is designed to conserve electrical energy
by reducing power consumption when there is no video-input signal present.
When there is no video input signal this monitor, following a time-out period,
will automatically switch to an OFF mode. This reduces the monitor's internal
power supply consumption. After the video input signal is restored, full power
is restored and the display is automatically redrawn. The appearance is similar
to a "Screen Saver" feature except the display is completely off. The display is
restored by pressing a key on the keyboard, or clicking the mouse.
USING THE RIGHT POWER CORD :
The accessory power cord for the Northern American region is the wallet plug
with NEMA 5-15 style and is UL listed and CSA labeled. The voltage rating for
the power cord shall be 125 volts AC.
Supplied with units intended for connection to power outlet of personal
computer: Please use a cord set consisting of a minimum No. 18 AWG, type
SJT or SVT three conductors flexible cord. One end terminates with a
grounding type attachment plug, rated 10A, 250V, CEE-22 male configuration.
The other end terminates with a molded-on type connector body, rated 10A,
250V, having standard CEE-22 female configuration.
Please note that power supply cord needs to use VDE 0602, 0625, 0821
approval power cord in European counties.
英文
12
TECHNICAL SUPPORT (FAQ)
Problem & Question
Power LED is not on
Possible Solution
*Check if the Power Switch is in the ON position
*Power Cord should be connected
*Check if the PC system is Plug & Play
compatible
No Plug & Play
*Check if the Video Card is Plug & Play
compatible
*Check if the D-15 plug pin of Video Cable is
bent
*Make sure the LCD Monitor Drivers are
installed
Picture is fuzzy
Picture bounces or
wave pattern is present in
the picture
*Adjust the Contrast and Brightness Controls.
*Move electrical devices that may cause
electrical interference.
a
The power LED is ON *Computer Power Switch should be in the ON
(orange) but there’s no
video or no picture.
position.
*Computer Video Card should be snugly seated
in its slot.
*Make sure monitor’s video cable is properly
connected to the computer.
*Inspect monitor’s video cable and make sure
none of the pins are bent.
*Make sure computer is operational by hitting
the CAPS LOCK key on the keyboard while
observing the CAPS LOCK LED. The LED
should either turn ON or OFF after hitting the
CAPS LOCK key.
Missing one of the *Inspect the monitor’s video cable and make
primary colors (RED,
GREEN, or BLUE)
Screen image is not
sure that none of the pins are bent.
*Adjust pixel frequency (CLOCK) and FOCUS or
centered or sized properly. press hot-key (AUTO)
Picture has color defects
(white does not look white)
*Adjust RGB color or select color temperature
Poor brightness or contrast *When the brightness of the screen lowers after
being used for a certain period and the function
of the display is affected, send it to our
authorized service center for repair.
Horizontal or vertical
*Use win 95/98 shut-down mode Adjust CLOCK
disturbances on the screen and FOCUS or perform hot- key (AUTO-key).
CLOCK (pixel frequency) controls the number of pixels scanned by one
horizontal sweep. If the frequency is not correct, the screen shows vertical
stripes and the picture has not correct width.
FOCUS adjusts the phase of the pixel clock signal. With a wrong phase
adjustment the picture has horizontal disturbances in light picture.
For FOCUS and CLOCK adjustment use “dot-pattern” or win 95/98 shut-down
mode pattern.
英文
13
ERROR MESSAGE & POSSIBLE SOLUTION
CABLE NOT CONNECTED :
1. Check that the signal-cable is properly connected , If the connector is
loose, tighten the connector’s screws.
2. Check the signal-cable’s connection pins for damage.
INPUT NOT SUPPORT :
Your computer has been set to unsuitable display mode ,set the computer to
display mode given in the following table.
英文
14
HOW TO INSTALL THE DRIVER-DISK (INF & ICM FILE)
FOR FIRST TIME INSTALL :
Your system may not recognize your flat-panel monitor,and as a result, you
may need to complete the following steps for optimum performance of your
monitor.
1. Check this LCD MONITOR is properly connected to your computer.
2. Restart the computer , when win95/98 detects the presence of a Plug and
Play Monitor ,its device driver can be loaded and configured dynamically,
insert LCD Monitor install disk to DISK A after the Win95/98 setup wizard
is appeared. This setup wizard will lead you through the steps for
configuring the system.
(Select “ NEXT “ for next steps and select driver A for LCD Monitor install
file, if not select driver A ,the configuration system will automatically select
the standard Plug and Play driver)
3. After the installation complete you can find the monitor complete name by
following steps :
Click “START” , select “SETTINGS”, select “CONTROL PANEL “Select
“SYSTEM”, select “ DEVICE MANAGEMENT “, select “MONITOR” icon
and click twice ,you can see the description as follow :
“AOC LM722 “
if this description doesn’t exist, or the “MONITOR” icon doesn’t exist
too,that means your installation is not successful.
Please delete the description with click the right button of mouse, and
select The “remove or erase” to delete the description, if your step is
successful, the “MONITOR “ icon will disappear.
Please repeat this 2nd, 3rd steps if not success
4. After you complete above setup, please follow the steps below to operate
your monitor at maximum performance :
A). Double click on the My Computer icon
B). Double click on the Control Panel icon
C). Double click on the Display icon, click on the Settings tab
D). In the Desktop Area drag the slider to resolution 1280x1024, and
set the Color palette for 16-bit color
E). Click on the Advanced Properties
F). Select the add-on card tab , set the refresh rate to 60 Hz, click the
OK button, and click on the CLOSE button
英文
15
APPENDIX
SPECIFICATIONS
Driving system TFT Color LCD
LCD Panel
Input
Size
Pixel pitch
Viewable angle
Response time 16 ms(typical)
Video
43.2cm(17.0")
0.264mm( H ) × 0.264mm( V )
140° (H) 120° (V)
R,G,B Analog Interface
Separate Sync. H/V TTL
H-Frequency
V-Frequency
30kHz – 80kHz
55-75Hz
Display Colors
Dot Clock
16.2M Colors
135MHz
Max. Resolution
Plug & Play
1280 × 1024 @75Hz
VESA DDC2BTM
≤45W
EPA ENERGY STAR® ON Mode
OFF Mode
≤2W
Input Connector
D-Sub 15pin
Input Video Signal
Analog:0.7Vp-p(standard),
75 OHM, Positive
Horizontal : 337.92mm
Vertical : 270.34mm
100~240VAC,47~63Hz
Operating Temp: 5° to 35°C
Storage Temp.: -20° to 60°C
Operating Humidity: 10% to 85%
376(W)×382(H)×163(D)mm
4.2kg
Maximum Screen Size
Power Source
Environmental
Considerations
Dimension
Weight (N. W.)
英文
16
Switch
• Auto Adjust Button
•
•
/ Brightness
/ Contrast
• Power Button
• MENU
External Controls:
Functions
• Contrast
• Brightness
• Focus
• Clock
• H. Position
• V. Position
• Auto Config
• OSD Setup
• Language
• (Warm)Color
• (Cool)Color
• USER Color temperature
• Reset
• Exit
45 Watts
Power Consumption
( Maximum )
Regulatory Compliance
UL, CSA,FCC,CE,TCO’99,
ISO13406-2
英文
17
Preset Display Modes
HORIZONTAL
FREQUENCY
VERTICAL
FREQUENCY
STANDARD
RESOLUTION
Dos-mode
Dos-mode
640 × 350
720 × 400
640 × 480
640 × 480
640 × 480
640 × 480
800 × 600
800 × 600
800 × 600
800 × 600
832 × 624
1024 × 768
1024 × 768
1024 × 768
1280 × 1024
1280 × 1024
31.47kHz
70Hz
70Hz
60Hz
66.6Hz
75Hz
72Hz
60Hz
75Hz
56Hz
72Hz
75Hz
60Hz
70Hz
75Hz
60Hz
75Hz
31.47kHz
31.47kHz
35.00kHz
37.50kHz
37.86kHz
37.879kHz
46.875kHz
35.16kHz
48.01kHz
49.725kHz
48.363kHz
56.476kHz
60.02kHz
64.00kHz
80.00kHz
VGA
SVGA
XGA
SXGA
英文
18
CONNECTOR PIN ASSIGNMENT
1
6
5
10
15
11
15 - Pin Color Display Signal Cable
PIN NO.
DESCRIPTION
PIN NO.
DESCRIPTION
1.
2.
3.
4.
5.
6.
7.
8.
Red
Green
Blue
RXD
Ground
R-Ground
G-Ground
B-Ground
9.
10.
11.
12.
13.
14.
15.
+5V
Detect Cable
TXD
DDC-Serial Data
H-Sync
V-Sync
DDC-Serial Clock
英文
19
|