Safety
National Conventions
The following subsections describe notational conventions used in this document.
Notes, Cautions, and Warnings
Throughout this guide, blocks of text may be accompanied by an icon and printed in
bold type or in italic type. These blocks are notes, cautions, and warnings, and they
are used as follows:
NOTE: A NOTE indicates important information that helps you make better use of
your computer system.
CAUTION: A CAUTION indicates either potential damage to hardware or loss of
data and tells you how to avoid the problem.
WARNING: A WARNING indicates the potential for bodily harm and tells you how to
avoid the problem. Some warnings may appear in alternate formats and may be
unaccompanied by an icon. In such cases, the specific presentation of the warning is
mandated by regulatory authority.
Installation
Do not place the monitor on an unstable cart, stand, tripod, bracket, or table. If
the monitor falls, it can injure a person and cause serious damage to this product. Use
only a cart, stand, tripod, bracket, or table recommended by the manufacturer or sold
with this product. Follow the manufacturer’s instructions when installing the product
and use mounting accessories recommended by the manufacturer. A product and cart
combination should be moved with care.
Never push any object into the slot on the monitor cabinet. It could damage
circuit parts causing a fire or electric shock. Never spill liquids on the monitor.
Do not place the front of the product on the floor.
Leave some space around the monitor as shown below. Otherwise,
air-circulation may be inadequate hence overheating may cause a fire or damage to
the monitor.
See below the recommended ventilation areas around the monitor when the monitor is
installed on the wall or on the stand:
Cleaning
Clean the cabinet regularly with cloth. You can use soft-detergent to wipe out
the stain, instead of strong-detergent which will cauterize the product cabinet.
When cleaning, make sure no detergent is leaked into the product. The cleaning
cloth should not be too rough as it will scratch the screen surface.
Other
If the product is emitting a strange smell, sound or smoke, disconnect the power
plug IMMEDIATELY and contact a Service Center.
Make sure that the ventilating openings are not blocked by a table or curtain.
Do not engage the LCD monitor in severe vibration or high impact conditions
during operation.
Do not knock or drop the monitor during operation or transportation.
Caution:
Must put unit in flat surface. Any uneven or sloped surface may result in unit damage
or injury to user.
Adjusting Viewing Angle
For optimal viewing, it is recommended to look at the full face of the monitor, and then
adjust the monitor's angle to your own preference.
Hold the stand so you will not topple the monitor when you change the monitor's
angle.
You are able to adjust the monitor's angle as below.
NOTE:
Do not touch the LCD screen when you change the angle. It may cause damage or
break the LCD screen.
Connecting the Monitor
Cable Connections In Rear of Monitor to Connect PC/Laptop:
Important!! Follow the software installation described on page 11 to 15 before
connecting the USB monitor to your Laptop/PC.
1 Connecting the LCD monitor to your computer
To protect the equipment, always turn off the computer before connecting.
-
-
Connect one end of the USB cable to the LCD monitor and the end of USB
cable to the computer.
Your computer should detect the USB Monitor automatically.
Follow the procedure described starting on page 16 to configure your USB Monitor.
2 Power
Note：Some computers may not provide enough power to the LCD monitor for one
USB port.
If so, connect the other USB connector on the Y end of the cable into another USB on
your computer or connect the DC input port with an external approved adapter with the
output rating of DC 5V, 3A.
Installation of USB Graphic software on
your computer
For Microsoft ® Windows® 7
Important!! Install the USB Graphic software first before connecting the USB
monitor to your computer.
1. Double click on Setup.exe.
The Windows User Account Control window opens (if enabled in the OS).
2. Click Yes.
The USB Monitor software end user license agreement window opens.
3. Click I Accept.
DisplayLink Core software and DisplayLink Graphics installs.
Note: The screen may flash or go black during the installation. The installation box
above will disappear but no message will be shown at the end of the installation.
4. Connect your AOC USB Monitor via the USB cable to your PC/Notebook. Installing
device driver message will be shown on the taskbar.
The Windows User Account control window opens.
5. Click YES.
DisplayLink will automatically install the AOC USB Monitor.
The DisplayLink software end user license agreement windows opens (see
above).
6. Click I Accept.
The DisplayLink USB Graphics software installs, without notification that it has
completed.
Note: On some machines you may need reboot before you can use your AOC USB
Monitor.
For Microsoft® Windows Vista®
Important!! DO NOT connect USB Monitor to your PC/Notebook before the
software install.
1. Double click on Setup.exe.
The Windows User Account Control window opens (if enabled in the OS).
2. Click Yes.
The USB Monitor software end user license agreement window opens.
3. Click I Accept.
DisplayLink Core software and DisplayLink Graphics installs.
Note: The screen may flash or go black during the installation. The installation
box above will disappear but no message will be shown at the end of the
installation.
4. Connect your AOC USB Monitor via the USB cable to your PC/Notebook. Installing
device driver message
The Windows User Account control window opens.
5. Click YES.
DisplayLink automatically installs the AOC USB Monitor.
The DisplayLink software end user license agreement windows opens (see
above).
6. Click I Accept.
The DisplayLink USB Graphics software installs, without notification that it has
completed.
Note: On some machines you may need reboot before you can use your AOC USB
Monitor.
For Microsoft® Windows® XP
Important!! DO NOT connect USB Monitor to your PC/Notebook before the
software install.
1. Double click on Setup.exe.
The Windows User Account Control window opens (if enabled in the OS).
2. Click I Accept.
DisplayLink core software and DisplayLink Graphics installs.
Note: The screen may flash or go black during the installation.
3. Connect your AOC USB Monitor via the USB cable to your PC/Notebook. The
following message (or similar) will be seen.
Windows installs the AOC USB Monitor device.
Note: The screen may flash or go black during the installation.
Setting the USB Monitor
Follow this procedure to configure the AOC Monitor
1. Open screen resolution
2. Set the display options. Refer to the table below for details on each option.
Menu
Sub-Menu
Description
Use the drop down list to select a display to be
configured.
Display
Use the drop down list and user the slider to choose a
resolution
Resolution
Orientation
Landscape
Set the display to landscape view
Set the display to portrait mode
Portrait
Landscape (flipped)
Portrait (flipped)
Duplicates these
displays
Set the display to upside down landscape mode
Set the display to upside down portrait mode
Reproduces the main display on the second display
Extend these displays
Extends the main display on the secondary display
The desktop appears on the display marked 1. The
display marked 2 become blank.
Multiple
Displays
Show Desktop only on 1
Shows Desktop only on
2
The desktop appears on the display marked 2. The
display marked 1 become blank.
To control the behavior of an attached AOC USB monitor, it is also possible to use
Windows Key ( ) + P to display a menu (and cycle through it) to switch mode.
To Control the Display
You can use the AOC USB LCD monitor in mirror mode or extended mode. Settings
may vary depending on your operating system.
For Microsoft® Windows® 7
Press the Windows® key ( ) + P to switch between different modes as shown below.
For Microsoft® Windows® XP and Microsoft® Windows
Vista®
Right-click the “ ”icon in the system tray of your Windows ® desktop to configure the
display settings.
Disconnecting the LCD Monitor
1. For Microsoft® Windows® 7 only, you can turn the monitor OFF by pressing the
Windows key ( ) + P, and then selecting “Computer only”.
For Microsoft® Windows vista® and Windows® XP, you can select OFF by
right-Clicking the “ ” icon in the system tray.
2. Remove the USB cable from the computer and monitor.
Cleaning the LCD Monitor
Please follow the guidelines below when cleaning the LCD Monitor:
-
-
-
Always unplug the monitor before cleaning.
Use a soft cloth to wipe the screen and other parts of the monitor
Never spray liquids directly onto the LCD screen or use harsh chemical
products to clean it.
Precautions:
for Microsoft ® Windows® XP, Windows Vista® and Windows® 7
Due to the configurations of computers and Windows® operating systems available,
functionality may differ slightly than stated in the user manual. This may be due to the
computer manufacture's BIOS and other custom configurations of the hardware,
pre-installed software or operating system installed at time of production. If you have
specific problems, you may need to contact the computer manufacturer to inquire
about BIOS, hardware driver or operating system updates.
-
The AOC USB Monitor utilizes an advanced video graphics controller to display
the video. However, due to USB 2.0 transfer speed limitations, some or all portions of
DVD playback may appear slow or choppy. This is not a malfunction of the Mobile
LCD monitor. Move the video playback from the Mobile LCD monitor to your computer
display for optimal video performance when viewing DVDs.
-
On Windows ® XP systems, DVDs may not display correctly on the Mobile LCD
monitor. Use your computer's built-in monitor to view DVDs.
-
-
This product does not support 3D programs.
In some software application programs that utilize certain direct draw commands
such as some 2D-Games, the display on the Mobile LCD monitor will not be supported.
If you want to play these games in full screen, we suggest you disconnect the Mobile
LCD monitor.
-
This product is unable to enter full screen DOS mode when using the Mobile LCD
monitor.
-
To play DVDs, use the Media Player included with your operating system.
Supported Media Player
Windows Media Player 11 (Windows Media Player 12. For windows 7)
WinDVD 10
PowerDVD 9 (Only for Windows Vista and 7)
RealPlayer 11
The DisplayLink USB Graphics device can display media files and DVDs using most
media players. But can’t guarantee performance, Media playback in mirror mode (XP)
or in Basic mode (Vista and Windows 7) is not recommended.
PC Requirements
DisplayLink software can be used on PCs, from Netbooks, Notebooks/Laptops to
Desktops. The driver will run on processors ranging from Atom N270 based PCs,
basic single Core CPUs, and of course the latest Dual, Quad Core and Core i3/i5/i7
CPUs.
The performance of the software is dependent upon the processing power available,
as well as the operating system in use. More capable systems offer higher
performance.
DisplayLink software is available for PCs running one of the following Windows
operating systems:
Windows 7 (32-bit or 64-bit)
Windows Vista with Service Pack 1 or 2 (32-bit or 64-bit)
Windows XP Home or Professional (including Tablet edition) with Service Pack 2
or 3
Windows Server 2003, 2008 and 2008 R2
DisplayLink provide a version of Software for Windows Multipoint server. Please visit
http://www.displaylink.com/support/downloads_wms.php to download software for
Windows Multipoint Server.
Note: 64-bit editions of XP are not supported. Mac OS X support can be found
Windows 7
For Windows 7, the Windows Experience Index (WEI) is a useful measure of hardware
level. The WEI is accessible from Computer > Properties, or from Control Panel >
System.
The recommended typical hardware requirements for the PC are:
WEI score of at least 3 in the ‘Graphics; Desktop performance for Windows Aero’
category.
Overall WEI score of at least 3 as recommended by Microsoft.
At least one USB 2.0 port.
30 megabytes (MB) of free disk space.
Computer screen for use with the DisplayLink device, if it is not integrated.
Network access for software downloads, or access to a CD-ROM drive.
Windows Vista
For Windows Vista, the Windows Experience Index (WEI) is a useful measure of
hardware level. The WEI is accessible from Computer > Properties, or from Control
Panel > System.
The recommended typical hardware requirements for the PC are:
WEI score of at least 3 in the 'Graphics; Desktop performance for Windows Aero'
category.
Overall WEI score of at least 3 as recommended by Microsoft.
At least one USB 2.0 port
30 megabytes (MB) of free disk space.
Computer screen for use with the DisplayLink device, if it is not integrated.
Network access for software downloads, or access to a CD-ROM drive.
If the PC specification is below this, performance will be lower (or CPU loading higher
than acceptable).
Windows XP
For 1-2 monitors, business usage, productivity target. This may not provide full frame
rate DVD playback at full screen.
1.2GHz Single Core CPU
512MB memory
For 3 monitors where 1 could run DVD video while also targeting productivity and
business apps. Will support only 1 video of DVD resolution at full screen:
1.6GHz CPU
1GB memory
For 6 screens where 1 screen can run full screen DVD video:
1.8GHz Core Duo
1GB memory
At least one USB 2.0 port.
30 megabytes (MB) of free disk space.
Computer screen for use with the DisplayLink device, if it is not integrated.
Network access for software downloads, or access to a CD-ROM drive.
Graphics Card Support (Windows Vista/Windows 7)
On Windows Vista and Windows 7, DisplayLink software interacts closely with the
primary graphics card. DisplayLink support and test a single graphics card (GPU)
installed in a PC from all major GPU vendors (Intel, ATI, NVidia and Via)
The following GPU configurations may exhibit compatibility issues on Windows 7 and
Vista in certain circumstances:
Switchable Graphics (ATI/Intel)
Switchable Graphics (ATI/ATI)
Switchable Graphics (NVIDIA/Intel)
NVIDIA SLI in SLI mode
Other GPU configurations, including the following, are currently unsupported and will
not function on Windows 7/Vista:
Hybrid Graphics
Hybrid SLI
Hybrid Crossfire
Crossfire
SLI not in SLI mode
Multiple WDDM 1.1 graphics drivers active at once
Graphics Card Support (Windows XP)
All graphics cards are supported on Windows XP.
Troubleshooting
This section provides tips for correcting problems, should any occur. It also describes
how to contact AOC should you encounter problems that you cannot resolve.
Before you call AOC service center, please read the troubleshooting advice in this
manual and in your computer User's Manual. You may also want to consult with your
system administrator or company technical support staff.
Problem & Question
Possible Solutions
Check the connectors. Make sure the USB cable is firmly
connected to the monitor
The monitor does not turn
on
Disconnect and reconnect the USB cable again.
Check the condition of the USB cable. If the cable is frayed or
damaged, replace the cable. If the connectors are soiled, wipe
them with a clean cloth.
Make sure the USB cable is properly connected the computer.
Make sure the computer is on and working. The computer may
be in sleep or power-saving mode, or displaying a blank screen
saver. Move the mouse to “wake up” the computer.
The screen is blank,
although the computer
power is on
The picture “bounces” or
moves in a wave-like
pattern
Move electrical devices that may cause electrical interference
away from the monitor.
Cannot play DVDs using
the Third-Party DVD player Use the Media Player included in your operating system.
program
Specification
General Specification
Model name
E2251FWU
Driving system
TFT Color LCD
546.7 mm diagonal
0.2482 (H)mm x 0.2482 (V)mm
R, G, B Analog interface
NA
Viewable Image Size
Pixel pitch
Panel
Video
Separate Sync.
Display Color
Dot Clock
16.7M Colors
148.5MHz
Horizontal scan range
67.5Khz
Horizontal scan
Size(Maximum)
476.64mm
60Hz
Vertical scan range
Vertical scan
Size(Maximum)
268.11mm
Optimal preset
resolution
1920×1080 @60Hz
Resolution
Plug & Play
VESA DDC2B
A-type USB
NA
Input Connector
Input Video Signal
Power Source
PC USB 5V
15 W
Power Consumption
Standby <1 W
NA
Off timer
Connector Type
Signal Cable Type
Dimensions & Weight:
Height
A-type USB
Detachable
389.1mm
512.2mm
193.7mm
2.65kg
Physical
Characteristics
Width
Depth
Weight (monitor only)
Weight (with packaging)
Temperature:
Operating
0° to 40°
Non-Operating
Humidity:
-25°to 55°
Environmental
Operating
10% to 85% (non-condensing)
5% to 93% (non-condensing)
Non-Operating
Altitude:
Operating
0~ 3658m (0~ 12000 ft )
0~ 12192m (0~ 40000 ft )
Non-Operating
Regulation
FCC Notice
FCC Class B Radio Frequency Interference Statement WARNING: (FOR FCC CERTIFIED MODELS)
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses and can radiate radio frequency energy, and if not
installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
NOTICE:
The changes or modifications not expressly approved by the party responsible for compliance could void the user's
authority to operate the equipment.
Shielded interface cables and AC power cord, if any, must be used in order to comply with the emission limits.
The manufacturer is not responsible for any radio or TV interference caused by unauthorized modification to this
equipment. It is the responsibilities of the user to correct such interference. It is the responsibility of the user to
correct such interference.
WEEE Declaration
Disposal of Waste Equipment by Users in Private Household in the European Union.
This symbol on the product or on its packaging indicates that this product must not be disposed of with your other
household waste. Instead, it is your responsibility to dispose of your waste equipment by handing it over to a
designated collection point for the recycling of waste electrical and electronic equipment. The separate collection
and recycling of your waste equipment at the time of disposal will help to conserve natural resources and ensure
that it is recycled in a manner that protects human health and the environment. For more information about where
you can drop off your waste equipment for recycling, please contact your local city office, your household waste
disposal service or the shop where you purchased the product.
EPA Energy Star
ENERGY STAR® is a U.S. registered mark. As an ENERGY STAR® Partner, AOC International (Europe) BV and
Envision Peripherals, Inc. have determined that this product meets the ENERGY STAR® guidelines for energy
efficiency.
Service
Warranty Statement for Europe
LIMITED THREE-YEAR WARRANTY*
AOC Color Monitors sold within Europe
AOC International (Europe) BV warrants this product to be free from defects in material and workmanship for a
period of Three (3) years after the original date of consumer purchase. During this period, AOC International
(Europe) BV will, at its option, either repair the defective product with new or rebuilt parts, or replace it with a new or
rebuilt product at no charge except as *stated below. The defective products that are replaced become the property
of AOC International (Europe) BV.
If the product appears to be defective, please contact your local dealer or refer to the warranty card when attached
to the product.
Deliver the product freight pre-paid, along with the dated proof of purchase, to the AOC Authorized Service Center.
If you cannot deliver the product in person:
Pack it in its original shipping container (or equivalent)
Put the RMA number on the address label
Put the RMA number on the shipping carton
Insure it (or assume the risk of loss/damage during shipment)
Pay all shipping charges
AOC International (Europe) BV is responsible neither for any damage or loss during inbound transport damage nor
to inbound product that was not properly packaged.
AOC International (Europe) BV will pay the return shipping charges within one of the countries specified within this
warranty statement. AOC International (Europe) BV is not responsible for any costs associated with the
transportation of product across international borders. This includes the international border within the European
Union.
* This limited warranty does not cover any losses or damages that occur as a result of
Shipping or improper installation or maintenance
Misuse
Neglect
Any cause other than ordinary commercial or industrial application
Adjustment by non-authorized source
Repair, modification, or installation of options or parts by anyone other than an AOC Authorized Service Center
Improper environment
Excessive or inadequate heating or air conditioning or electrical powers failures, surges, or other irregularities
This limited warranty does not cover any of the product firmware or hardware that you or any third party have
modified or altered; you bear the sole responsibility and liability for any such modification or alteration.
ALL EXPRESS AND IMPLIED WARRANTIES FOR THIS PRODUCT (INCLUDING THE WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE) ARE LIMITED IN DURATION TO A
PERIOD OF THREE (3) YEARS FOR PARTS AND LABOR FROM THE ORIGINAL DATE OF CONSUMER
PURCHASE. NO WARRANTIES (EITHER EXPRESSED OR IMPLIED) APPLY AFTER THIS PERIOD.
AOC INTERNATIONAL (EUROPE) BV OBLIGATIONS AND YOUR REMEDIES HEREUNDER ARE SOLELY AND
EXCLUSIVELY AS STATED HERE. AOC INTERNATIONAL (EUROPE) BV LIABILITY, WHETHER BASED ON
CONTRACT, TORT, WARRANTY, STRICT LIABILITY, OR OTHER THEORY, SHALL NOT EXCEED THE PRICE
OF THE INDIVIDUAL UNIT WHOSE DEFECT OR DAMAGE IS THE BASIS OF THE CLAIM. IN NO EVENT
SHALL AOC INTERNATIONAL (EUROPE) BV BE LIABLE FOR ANY LOSS OF PROFITS, LOSS OF USE OR
FACILITIES OR EQUIPMENT, OR OTHER INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGE. SOME
STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL
DAMAGES, SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU. ALTHOUGH THIS LIMITED WARRANTY
GIVES YOU SPECIFIC LEGAL RIGHTS, YOU MAY HAVE OTHER RIGHTS, WHICH MAY VARY FROM
COUNTRY TO COUNTRY. THIS LIMITED WARRANTY IS ONLY VALID FOR PRODUCTS PURCHASED IN THE
MEMBER COUNTRIES OF THE EUROPEAN UNION.
Information in this document is subject to change without notice.
For more details, please visit: http://www.aoc-europe.com/en/service/index.php
Warranty Statement for North & South America (excluding
Brazil)
WARRANTY STATEMENT
for AOC Color Monitors
Including those Sold within North America as Specified
Envision Peripherals, Inc. warrants this product to be free from defects in material and workmanship for a period of
three (3) years for parts & labor and one (1) year for CRT Tube or LCD Panel after the original date of consumer
purchase. During this period, EPI ( EPI is the abbreviation of Envision Peripherals, Inc. ) will, at its option, either
repair the defective product with new or rebuilt parts, or replace it with a new or rebuilt product at no charge except
as *stated below. The parts or product that are replaced become the property of EPI.
In the USA to obtain service under this limited warranty, call EPI for the name of the Authorized Service Center
closest to your area. Deliver the product freight pre-paid, along with the dated proof of purchase, to the EPI
Authorized Service Center. If you cannot deliver the product in person:
Pack it in its original shipping container (or equivalent)
Put the RMA number on the address label
Put the RMA number on the shipping carton
Insure it (or assume the risk of loss/damage during shipment)
Pay all shipping charges
EPI is not responsible for damage to inbound product that was not properly packaged.
EPI will pay the return shipment charges within one of the countries specified within this warranty statement. EPI is
not responsible for any costs associated with the transportation of product across international borders. This
includes the international borders of the countries within this warranty statements.
In the United States and Canada contact your Dealer or EPI Customer Service, RMA Department at the toll free
* This limited warranty does not cover any losses or damages that occur as a result of:
Shipping or improper installation or maintenance
Misuse
Neglect
Any cause other than ordinary commercial or industrial application
Adjustment by non-authorized source
Repair, modification, or installation of options or parts by anyone other than an EPI Authorized Service Center
Improper environment
Excessive or inadequate heating or air conditioning or electrical power failures, surges, or other irregularities
This three-year limited warranty does not cover any of the product's firmware or hardware that you or any third
party have modified or altered; you bear the sole responsibility and liability for any such modification or alteration.
ALL EXPRESS AND IMPLIED WARRANTIES FOR THIS PRODUCT (INCLUDING THE WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE) ARE LIMITED IN DURATION TO A
PERIOD OF THREE (3) YEARS FOR PARTS AND LABOR AND ONE (1) YEAR FOR CRT TUBE OR LCD PANEL
FROM THE ORIGINAL DATE OF CONSUMER PURCHASE. NO WARRANTIES (EITHER EXPRESSED OR
IMPLIED) APPLY AFTER THIS PERIOD. IN THE UNITED STATES OF AMERICA, SOME STATES DO NOT
ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATIONS MAY
NOT APPLY TO YOU.
EPI OBLIGATIONS AND YOUR REMEDIES HEREUNDER ARE SOLELY AND EXCLUSIVELY AS STATED HERE.
EPI’ LIABILITY, WHETHER BASED ON CONTRACT, TORT. WARRANTY, STRICT LIABILITY, OR OTHER
THEORY, SHALL NOT EXCEED THE PRICE OF THE INDIVIDUAL UNIT WHOSE DEFECT OR DAMAGE IS THE
BASIS OF THE CLAIM. IN NO EVENT SHALL ENVISION PERIPHERALS, INC. BE LIABLE FOR ANY LOSS OF
PROFITS, LOSS OF USE OR FACILITIES OR EQUIPMENT OR OTHER INDIRECT, INCIDENTAL, OR
CONSEQUENTIAL DAMAGE. IN THE UNITED STATES OF AMERICA, SOME STATES DO NOT ALLOW THE
EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES. SO THE ABOVE LIMITATION
MAY NOT APPLY TO YOU. ALTHOUGH THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS.
YOU MAY HAVE OTHER RIGHTS WHICH MAY VARY FROM STATE TO STATE.
In the United States of America, this limited warranty is only valid for Products purchased in the Continental United
States, Alaska, and Hawaii.
Outside the United States of America, this limited warranty is only valid for Products purchased in Canada.
Information in this document is subject to change without notice.
For more details, please visit:
ARGENTINA: http://ar.aoc.com/support/warranty
BOLIVIA: http://bo.aoc.com/support/warranty
COLOMBIA: http://co.aoc.com/warranty
COSTA RICA: http://cr.aoc.com/support/warranty
DOMINICAN REPUBLIC: http://do.aoc.com/support/warranty
EL SALVADOR: http://sv.aoc.com/support/warranty
GUATEMALA: http://gt.aoc.com/support/warranty
HONDURAS: http://hn.aoc.com/support/warranty
NICARAGUA: http://ni.aoc.com/support/warranty
PARAGUAY: http://py.aoc.com/support/warranty
URUGUAY: http://pe.aoc.com/warranty
VENEZUELA: http://ve.aoc.com/support/warranty
IF COUNTRY NOT LISTED: http://latin.aoc.com/warranty
CE Declaration of Conformity
For the following equipment:
LCD Monitor
(Product Name)
E2251FWu
(Model Designation / Brand Name)
is herewith confirmed to comply with the requirements set out in the Council Directive on the
Approximation of the Laws of the Member States relating to Electromagnetic Compatibility
(2004/108/EC), Low-voltage Directive (2006/95/EC), ErP Directive (2005/32/EC). For the
evaluation regarding the Directives, the following standards were applied:
STANDARDS
Report/Technical File
1110041
Tested by:
Audix Technology(Shenzhen)CO.,LTD
EN 55022:2006+A1:2007,Class B
EN 61000-3-2: 2006
EN 61000-3-3: 2008
EN 55024: 1998+A1:2001+A2:2003
17019448
Tested by:TUV
EN 60950-1: 2006+A11:2009
TPVRDSE- E2251FWu -EUP
Tested by:TPV
EN 62301: 2005
CE Mark first affixed in: 2011
The following importer/manufacturer is responsible for this declaration:
TPV ELECTRONICS (Fujian) CO., LTD.
(Company Name, Importer)
(Company Address, Importer)
(Company Name, Manufacturer)
Shangzheng,Yuanhong
Road,FuQing,Fujian,China
(Company Address, Manufacturer)
Person responsible for this declaration:
(Name, Surname, Importer)
Person responsible for this declaration:
Jingle.Xie
(Name, Surname, Manufacturer)
Manager of Safety Department
(Position/Title)
(Position/Title)
(Legal Signature)
(Legal Signature)
China
November 10, 2011
(Place)
(Date)
(Place)
(Date)
Only for AOC branded monitors sold within the continental United States.
All AOC brandedmonitors are now covered by the EASE Program. If your monitor malfunctions at any time during the first
three months, AOC will provide a replacement monitor within 72 hours after you are approved for our program. If your
monitor qualifies for the EASE program, AOC will pay for freight both ways.
Step 1: Phone our TECH Department at 888.662.9888
Step 2: Fill out and return EASE registration forms by mail or fax.
Step 3: We will issue a Return Authorization Number upon verification into the program.
Step 4: A monitor will be advance shipped to your location.
Step 5: We will issue a UPS Call Tag to pick up the defective unit.
Step 6: Please review the following chart to see your EASE program qualifications.
WARRANTY
PERIOD
COVERAGE AT
NO CHARGE
CUSTOMER
CHARGES
- None*
Within the first three months of - New AOC monitor
purchase: Covered by EASE
- Call tag dispatched and return freight
charges via UPS
Between 4 months – 1 Year
- All Parts & Labor Including CRT - UPS Return Freight to AOC
Tube & LCD Panel
Between 1 Year - 3 Years:
Covered by standard limited
warranty
- Parts & Labor (excluding CRT Tube
& LCD Panel)
- UPS Return Freight to AOC
*AOC will need to obtain a credit card number if you would like to get a new AOC monitor advanced shipped to your location, prior to the defective unit
arriving at AOC’s service center. If you do not wish to supply a credit card, AOC will only ship the new monitor, once the defective unit arrives at the AOC
service center.
|
