AG Neovo TV 01 User Manual

Table of Contents  
Features  
2
2
3
System Requirements  
Package Contents  
Part Identification  
Remote Controller  
Installation  
4
5
6
8
チューナー フレーム  
FCC Notice  
1
Parts Identification  
Front view  
Remote controller  
1
2
3
4
5
6
7
8
0…9, 100: for direct channel selection  
CH▲▼: channel selection  
1. Remote control receiver window  
2. Picture frame  
VOL▲▼: volume control  
RETURN: return to last selected channel  
CH +/-: to add or erase channel  
TV/CATV: select TV or cable TV  
MUTE: to enable/disable the audio mute function  
MTS: to select audio mode (mono/stereo/sap)  
(This function is only feasible for NTSC system.)  
9
SCAN: to scan the available channels and to memorize  
automatically  
10 RECALL: to show current status  
Back view  
11 TV/PC: to switch between TV and PC screens (This function  
may not be feasible if you are not using an AG neovo monitor.)  
Sꢀ DC 9V IN (for power input)  
Sꢀ ANT INPUT (for antenna signal input)  
Sꢀ VIDEO OUTPUT (for video signal output)  
Sꢀ AUDIO OUTPUT (for audio signal output)  
Associated Industries China, Inc.  
MODEL NO.: TV-01  
This device complies with Part 15 of the FCC  
Rules.Operation is subject to the following two  
conditions:(1)this device may not cause harmful  
interference,and(2)this device must accept any  
interference received,including interference that  
may cause undesired operation.  
ꢆꢇꢁ  
檢磁 XXXXXXXX  
ꢉꢀ  
ꢅ  
ꢄ  
ꢊꢂꢋ  
ꢅꢆꢄꢇ ꢈꢉ  
ꢀ ꢁ ꢂ ꢃ  
S/N:FTB 0XX00001  
MADE IN TAIWAN. ꢆꢇꢈꢉꢊꢋ  
ꢀꢁꢂꢃꢄꢄ  
Ly  
ANT  
INPUT  
VIDEO  
OUTPUT  
AUDIO  
OUTPUT  
DC 9V IN  
4
5
Installation  
4.3 Insert the photograph and be sure it is positioned properly.  
The photograph should not cover the remote control receiver  
window. Otherwise, the remote controller will be no function.  
1
Installation of TV tuner function  
1.1 Plug the TV antenna or cable TV connection to the “ANT  
INPUT” on the rear of the TV Tuner Frame.  
1.2 Connect the “VIDEO OUTPUT” port on the rear of the TV  
Tuner Frame to the “VIDEO INPUT” port of LCD monitor  
by using the video cable included.  
1.3 Connect the “AUDIO OUTPUT” port on the rear of the TV  
Tuner Frame to the “AUDIO INPUT” of speaker by using  
the audio cable included.  
1.4 Plug power connection of power adapter into the “DC 9V  
IN” port on the rear of the TV Tuner Frame.  
2
Installation of remote controller  
2.1 Remove the battery cover on the rear of remote controller.  
2.2 Insert the batteries included into the slot. Be sure the  
direction of battery’s pole is correct.  
2.3 Attach the cover back to the remote controller.  
Setup of TV channels  
3
4
3.1 Turn on the LCD monitor connected to the TV Tuner  
Frame.  
3.2 Press the SCAN button on the remote controller to scan all  
the available channels automatically.  
Installation of photograph to the frame  
4.1 Remove the photograph inside the frame already. You  
may need to shake the TV Tuner Frame up and down.  
4.2 The frame is designed for photographs up to 5” by 3” (12.7  
by 7.6 cm) size. You may need to refine the size of your  
photograph to fit into the frame.  
6
7
FCC NOTICE  
This device complies with Part 15 of the FCC Rules. Operation is  
subject to the following two  
conditions :  
(1) this device may not cause harmful interface, and  
(2) this device must accept any interference received, including  
interference that may cause undesired operation.  
8

HP Hewlett Packard Hewlett Packard Computer Monitor L2208W User Manual
GN Netcom 5830 User Manual
GE JP980 User Manual
GE Built In Gas s JGP330 User Manual
DCS CP 484GG User Manual
Cypress Perform CY7C1411BV18 User Manual
Cisco Systems Cisco Unified Wireless IP Phone 7920 User Manual
AT T DECT CL82609 User Manual
Asus P4B MX User Manual
Asus A7V133 User Manual