FLAIL
SHREDDER
Center Drive
S15CD
S20CD
S22CD
S25CD
S27CD
TABLE OF CONTENTS
INTRODUCTION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
SPECIFICATIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
BALANCE STATEMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
GENERAL INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
SAFETY RULES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-9
SAFETY DECALS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-12
OPERATOR SIGN-OFF RECORD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
FIELD OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
OPTIONAL EQUIPMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
SHREDDER STORAGE & CLEANING. . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
SERVICE & MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35
CONTOUR FLAIL PATTERN WORKSHEETS . . . . . . . . . . . . . . . . . . . . . . .36
ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38
DEALER CHECK LISTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45
INDEX TO PARTS LISTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47
BOLT TORQUE CHART . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .63
BOLT SIZE CHART & ABBREVIATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . .64
INDEX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .65
PRODUCT WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .64
REPLACEMENT PARTS WARRANTY . . . . . . . . . . . . INSIDE BACK COVER
!
LEA EL INSTRUCTIVO!
Si no lee Ingles, pida ayuda a
alguien que si lo lea para que le
traduzca las medidas de seguridad.
MAN0506 (Rev. 9/5/2008)
Introduction 3
SPECIFICATIONS
Maximum Outside Body Width:
15′ . . . . . . . . . . . . . . . . . .189 in. (4.9 m)
20′ . . . . . . . . . . . . . . . . . .253 in. (6.4 m)
22′ . . . . . . . . . . . . . . . . . .277 in. (7.0 m)
25′ . . . . . . . . . . . . . . . . . .309 in. (7.8 m)
27′ . . . . . . . . . . . . . . . . . .334 in. (8.4 m)
Cutting Height: . . . . . . . . . . . . . . . . . . . . 3 - 18 in. (7.62 cm to 45.7 cm)
Width of Cut:
15′ . . . . . . . . . . . . . . . . . .183 in. (4.6 m)
20′ . . . . . . . . . . . . . . . . . .247 in. (6.2 m)
22′ . . . . . . . . . . . . . . . . . .271 in. (6.8 m)
25′ . . . . . . . . . . . . . . . . . .303 in. (7.6 m)
27′ . . . . . . . . . . . . . . . . . .327 in. (8.3 m)
Knives:
Cups
“L”
“L” Cut-Off
Number on 15′. . . . . . . . . . . . 84. . . . . . . . . . . 164. . . . . . . . . . . . 4
Number on 20′. . . . . . . . . . . . 116. . . . . . . . . . 228. . . . . . . . . . . . 4
Number on 22′. . . . . . . . . . . . 128. . . . . . . . . . 252. . . . . . . . . . . . 4
Number on 25′. . . . . . . . . . . . 144. . . . . . . . . . 284. . . . . . . . . . . . 4
Number on 27′. . . . . . . . . . . . 156. . . . . . . . . . 308. . . . . . . . . . . . 4
Recommended Tire Size:. . . . . . . . . . . . 9.5L - 15,6 ply rated
Tire Inflation Pressure: . . . . . . . . . . . . . . 25 psi
Rotor: Speed . . . . . . . . . . . . . . . . . . . . . 1350 RPM dynamically balanced
Drive: PTO . . . . . . . . . . . . . . . . . . . . . . . 1000 RPM
Weight of Shredder (approximate):
15′ w/2 casters* . . . . 3600 lbs (1633 kg)
20′ w/4 casters* . . . . 4800 lbs (2177 kg)
22′ w/4 casters* . . . . 5100 lbs (2313 kg)
25′ w/4 casters* . . . . 5600 lbs (2540 kg)
27′ w/4 casters* . . . . 5900 lbs (2676 kg)
*
each caster assembly weighs
approximately 214 lbs
4 Introduction
MAN0506 (Rev. 9/5/2008
IMPORTANT!
BALANCE STATEMENT
Both of the Woods Center Drive Shredder flail tubes
wear unevenly. This can reduce their chopping
effect and also increase vibration levels.
are balanced as rotor assemblies to meet or exceed
factory standards before installation. After installation,
the shredders are statistically inspected to check bal-
ance. These factory efforts allow the shredder to oper-
ate smoothly and be free of excessive vibration when
delivered to the customer.
●
●
●
Hitting large rocks or other foreign objects can
damage knives and other rotor parts, causing
excessive vibration.
Over time, certain types of soil and crops can also
lead to uneven knife wear and increased vibration
levels.
Once field operation has been started, it is the
operator’s responsibility to check and maintain
shredder rotor balance.
■ The operator must be familiar with all safety
rules and safety decals before installing and run-
ning the shredder. All personnel must be familiar
with and stay out of the hazard area whenever the
shredder is running. (See Figure 18, page 22).
●
●
If knife replacement is required due to wear or
damage, refer to REPLACING FLAILS, page 29.
Throughout the life of the flail shredder, removing
the flail tubes for replacement or re-balance may
be necessary.
Smooth, acceptable vibration levels can be easily esti-
mated in the field. After machine shutdown and coast
down has been completed, place a quarter on a clean
top panel of the shredder. At full rotor rpm (while main-
taining all safety rules regarding safe distances from
rotating equipment) observe the quarter. If the quarter
stays still and does not bounce around, the operator
can estimate that the shredder is free from excessive
vibration. If the quarter jumps around during full rotor
rpm, the shredder may be operating with excessive
vibration where troubleshooting and maintenance are
required (refer to the Troubleshooting section).
●
If flail tube replacement is required due to wear or
damage, refer to SERVICING ROTORS (FLAIL
TUBES), page 30.
●
●
●
Any re-balance should be done with all knives
installed.
Factory balanced repair rotors are available
through your local Woods dealer.
Consult with your local balance shop experts or
contact Woods Technical Service for re-balance or
replacement options.
The Woods Center Drive Flail Shredder has been
designed for maximum durability when shredding any
type of crop. While operating in the field, many factors
can affect and degrade shredder rotor balance and
cause increased vibration levels.
Continued operation with excessive vibration can
cause damage to and shorten component life, void
product warranty, and affect personal safety. Checking
and maintaining shredder rotor balance is the owner/
operator’s responsibility.
●
Operating too low to the ground or in frequent con-
tact with the ground can cause the flail knives to
GENERAL INFORMATION
The purpose of this manual is to assist you in operating
and maintaining your flail shredder. Read it carefully. It
furnishes information and instructions that will help you
achieve years of dependable performance. These
instructions have been compiled from extensive field
experience and engineering data. Some information
may be general in nature due to unknown and varying
operating conditions. However, through experience
and these instructions, you should be able to develop
procedures suitable to your particular situation.
The illustrations and data used in this manual were cur-
rent at the time of printing but, due to possible inline
production changes, your machine may vary slightly in
detail. We reserve the right to redesign and change the
machines as may be necessary without notification.
Throughout this manual, references are made to right
and left directions. These are determined by standing
behind the equipment facing the direction of forward
travel.
MAN0506 (Rev. 9/5/2008)
Introduction 5
SAFETY RULES
ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED!
PREPARATION
„ Use a suitable lifting device of sufficient capac-
ity. Use adequate personnel to handle heavy com-
ponents.
Safety is a primary concern in the design and
manufacture of our products. Unfortunately, our
efforts to provide safe equipment can be wiped
out by an operator’s single careless act.
„ Check that all hardware is properly installed.
Always tighten to torque chart specifications
unless instructed otherwise in this manual.
In addition to the design and configuration of
equipment, hazard control and accident preven-
tion are dependent upon the awareness, concern,
„ Air in hydraulic systems can cause erratic oper-
ation and allows loads or equipment components
to drop unexpectedly. When connecting equipment
or hoses or performing any hydraulic maintenance,
purge any air in hydraulic system by operating all
hydraulic functions several times. Do this before
putting into service or allowing anyone to
approach the equipment.
judgement, and proper training of personnel
involved in the operation, transport, maintenance
and storage of equipment.
It has been said “The best safety device is an
informed, careful operator.” We ask you to be that
kind of operator.
TRAINING
„ Make sure all hydraulic hoses, fittings, and
valves are in good condition and not leaking before
starting power unit or using equipment. Check and
route hoses carefully to prevent damage. Hoses
must not be twisted, bent sharply, kinked, frayed,
pinched, or come into contact with any moving
parts. Operate moveable components through full
operational range to check clearances. Replace
any damaged hoses immediately.
„ Safety instructions are important! Read all
attachment and power unit manuals; follow all
safety rules and safety decal information. (Replace-
ment manuals and safety decals are available from
your dealer. To locate your nearest dealer, check
or in the United States and Canada call 1-800-319-
6637.) Failure to follow instructions or safety rules
can result in serious injury or death.
„ Always wear relatively tight and belted clothing
to avoid getting caught in moving parts. Wear
sturdy, rough-soled work shoes and protective
equipment for eyes, hair, hands, hearing, and head;
and respirator or filter mask where appropriate.
„ If you do not understand any part of this manual
and need assistance, see your dealer.
„ Know your controls and how to stop engine and
attachment quickly in an emergency.
„ When attaching a pull-type unit to the tractor
drawbar, always use a high-strength drawbar pin.
The drawbar pin must have a device that will lock it
into position. Secure safety chain to attachment
and tractor.
„ Operators must be instructed in and be capable
of the safe operation of the equipment, its attach-
ments, and all controls. Do not allow anyone to
operate this equipment without proper instruc-
tions.
„ Make sure attachment is properly secured,
adjusted, and in good operating condition.
„ Keep hands and body away from pressurized
lines. Use paper or cardboard, not hands or other
body parts to check for leaks. Wear safety goggles.
Hydraulic fluid under pressure can easily penetrate
skin and will cause serious injury or death.
„ Make sure spring-activated locking pin or collar
slides freely and is seated firmly in tractor PTO
spline groove.
„ Before starting power unit, check all equipment
driveline guards for damage. Replace any damaged
guards. Make sure all guards rotate freely on all
drivelines. If guards do not rotate freely on drive-
lines, repair and replace bearings before putting
equipment into service.
„ Make sure that all operating and service person-
nel know that if hydraulic fluid penetrates skin, it
must be surgically removed as soon as possible by
a doctor familiar with this form of injury or gan-
grene, serious injury, or death will result. CON-
TACT A PHYSICIAN IMMEDIATELY IF FLUID
ENTERS SKIN OR EYES. DO NOT DELAY.
„ Power unit must be equipped with ROPS or
ROPS cab and seat belt. Keep seat belt securely
fastened. Falling off power unit can result in death
from being run over or crushed. Keep foldable
ROPS system in “locked up” position at all times.
„ Never allow children or untrained persons to
operate equipment.
6 Safety
CD Flail Shredder MAN0506 (4/15/2006)
SAFETY RULES
ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED!
„ Connect PTO driveline directly to power unit
PTO shaft. Never use adapter sleeves or adapter
shafts. Adapters can cause driveline failures due to
incorrect spline or incorrect operating length and
can result in personal injury or death.
attachments are in transport position. Without this
weight, front tractor wheels could raise up result-
ing in loss of steering. The weight may be attained
with front wheel weights, ballast in tires or front
tractor weights. Weigh the tractor and equipment.
Do not estimate.
„ Inspect rubber flaps and swing rod before each
use. Replace if damaged or missing. Flaps must
pivot and hang freely so there are no gaps. Do not
put equipment into service until repaired.
„ Always raise unit and install transport locks
before transporting. Leak down or failure of
mechanical or hydraulic system can cause equip-
ment to drop.
„ Remove accumulated debris from this equip-
ment, power unit, and engine to avoid fire hazard.
„ Always attach safety chain to tractor drawbar
when transporting unit.
„ Make sure all safety decals are installed.
Replace if damaged. (See Safety Decals section for
location.)
OPERATION
„ Do not allow bystanders in the area when oper-
ating, attaching, removing, assembling, or servic-
ing equipment.
„ Make sure shields and guards are properly
installed and in good condition. Replace if dam-
aged.
„ Keep bystanders away from equipment.
„ A minimum 20% of tractor and equipment
weight must be on the tractor front wheels when
attachments are in transport position. Without this
weight, tractor could tip over, causing personal
injury or death. The weight may be attained with a
loader, front wheel weights, ballast in tires or front
tractor weights. Weigh the tractor and equipment.
Do not estimate.
„ Do not operate or transport equipment while
under the influence of alcohol or drugs.
„ Operate only in daylight or good artificial light.
„ Keep hands, feet, hair, and clothing away from
equipment while engine is running. Stay clear of all
moving parts.
„ Inspect and clear area of stones, branches, or
other hard objects that might be thrown, causing
injury or damage.
„ Always comply with all state and local lighting
and marking requirements.
„ Never allow riders on power unit or attachment.
TRANSPORTATION
„ Power unit must be equipped with ROPS or
ROPS cab and seat belt. Keep seat belt securely
fastened. Falling off power unit can result in death
from being run over or crushed. Keep foldable
ROPS system in “locked up” position at all times.
„ Power unit must be equipped with ROPS or
ROPS cab and seat belt. Keep seat belt securely
fastened. Falling off power unit can result in death
from being run over or crushed. Keep foldable
ROPS system in “locked up” position at all times.
„ Always sit in power unit seat when operating
controls or starting engine. Securely fasten seat
belt, place transmission in neutral, engage brake,
and ensure all other controls are disengaged
before starting power unit engine.
„ Always sit in power unit seat when operating
controls or starting engine. Securely fasten seat
belt, place transmission in neutral, engage brake,
and ensure all other controls are disengaged
before starting power unit engine.
„ Operate tractor PTO at the rpm speed stated in
“Specifications” section.
„ A minimum 20% of tractor and equipment
weight must be on the tractor front wheels when
(Safety Rules continued on next page)
CD Flail Shredder MAN0506 (4/15/2006)
Safety 7
SAFETY RULES
ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED!
(Safety Rules continued from previous page)
„ Use a suitable lifting device of sufficient capac-
ity. Use adequate personnel to handle heavy com-
ponents.
„ Look down and to the rear and make sure area
is clear before operating in reverse.
„ Always wear relatively tight and belted clothing
to avoid getting caught in moving parts. Wear
sturdy, rough-soled work shoes and protective
equipment for eyes, hair, hands, hearing, and head;
and respirator or filter mask where appropriate.
„ Do not operate or transport on steep slopes.
„ Do not stop, start, or change directions sud-
denly on slopes.
„ Use extreme care and reduce ground speed on
„ Do not allow bystanders in the area when oper-
ating, attaching, removing, assembling, or servic-
ing equipment.
slopes and rough terrain.
„ Watch for hidden hazards on the terrain during
operation.
„ Never go underneath equipment (lowered to the
ground or raised) unless it is properly blocked and
secured. Never place any part of the body under-
neath equipment or between moveable parts even
when the engine has been turned off. Hydraulic
system leak down, hydraulic system failures,
mechanical failures, or movement of control levers
can cause equipment to drop or rotate unexpect-
edly and cause severe injury or death. Follow Oper-
ator's Manual instructions for working underneath
and blocking requirements or have work done by a
qualified dealer.
„ Stop power unit and equipment immediately
upon striking an obstruction. Turn off engine,
remove key, inspect, and repair any damage before
resuming operation.
„ Leak down or failure of mechanical or hydraulic
system can cause equipment to drop.
MAINTENANCE
„ Before dismounting power unit or performing
any service or maintenance, follow these steps:
disengage power to equipment, lower the 3-point
hitch and all raised components to the ground,
operate valve levers to release any hydraulic pres-
sure, set parking brake, stop engine, remove key,
and unfasten seat belt.
„ Make sure attachment is properly secured,
adjusted, and in good operating condition.
„ Keep all persons away from operator control
area while performing adjustments, service, or
maintenance.
„ Before performing any service or maintenance,
lower equipment to ground or block securely, turn
off engine, remove key, and disconnect driveline
from tractor PTO.
„
Make certain all movement of equipment com-
ponents has stopped before approaching for ser-
vice.
„ Before working underneath, read manual
instructions, securely block up, and check stability.
Secure blocking prevents equipment from drop-
ping due to hydraulic leak down, hydraulic system
failure, or mechanical component failure.
„ Air in hydraulic systems can cause erratic oper-
ation and allows loads or equipment components
to drop unexpectedly. When connecting equipment
or hoses or performing any hydraulic maintenance,
purge any air in hydraulic system by operating all
hydraulic functions several times. Do this before
putting into service or allowing anyone to
approach the equipment.
„ Work not covered in SERVICE & MAINTENANCE
must be done by a qualified dealership. Special
skills, tools, and safety procedures may be
required. Failure to follow these instructions can
result in serious injury or death.
„ Do not handle blades with bare hands. Careless
or improper handling may result in serious injury.
„ Do not modify or alter or permit anyone else to
modify or alter the equipment or any of its compo-
nents in any way.
„ Your dealer can supply genuine replacement
blades. Substitute blades may not meet original
equipment specifications and may be dangerous.
„ Your dealer can supply original equipment
hydraulic accessories and repair parts. Substitute
parts may not meet original equipment specifica-
tions and may be dangerous.
„ Tighten all bolts, nuts, and screws to torque
chart specifications. Check that all cotter pins are
installed securely to ensure equipment is in a safe
condition before putting unit into service.
8 Safety
CD Flail Shredder MAN0506 (4/15/2006)
SAFETY RULES
ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED!
„ Make sure all safety decals are installed.
„ Leak down or failure of mechanical or hydraulic
Replace if damaged. (See Safety Decals section for
location.)
system can cause equipment to drop.
„ Make sure shields and guards are properly
installed and in good condition. Replace if dam-
aged.
STORAGE
„ Block equipment securely for storage.
„ Keep children and bystanders away from stor-
age area.
„ Do not disconnect hydraulic lines until engine is
stopped, power unit is properly secured, equip-
ment and all components are lowered to the
ground, and system pressure is released by oper-
ating all valve control levers.
„ Follow manual instructions for storage.
™
CD Flail Shredder MAN0506 (4/15/2006)
Safety 9
SAFETY & INSTRUCTIONAL DECALS
ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED!
Replace Immediately If Damaged!
3 - SERIAL NUMBER PLATE
1 - YELLOW REFLECTOR PN 20034004
2 - RED REFLECTOR PN 57123
MODEL NO.
SERIAL NO.
4 - RED-ORANGE FLUORESCENT MATERIAL
PN 20034034
Woods Equipment Company
Oregon, Illinois, U.S.A.
5 - PN 50030977
CAUTION PRECAUCION
1. Read Operator's Manual before starting.
1. Lea el Manual del Operario antes de empezar.
2. Stop tractor engine, place all controls in
neutral, lower machine to the ground, set
park brake, remove ignition key, and wait
for all moving parts to stop before
servicing, adjusting, repairing, or
unplugging.
2. Pare el motor del tractor, ponga todos los controles en
neutro, baje la máquina hasta el suelo, ponga el freno de
estacionamiento, quite la llave del encendido, y espere a
que todas las pizas móviles hayan parado antes de dar
servicio, hacer ajustes, reparaciones, o de desatascar.
3. Mantenga cerrados y asegurados todos los protectores y
las compuertas antes de poner a funcionar la máquina.
3. Keep all guards and access doors closed
and secured before operating.
4. Mantenga retirados de las piezas móviles, las manos, los
pies, el pelo, y la ropa.
4. Keep hands, feet, hair, and clothing away
from moving parts.
5. No permita que nadie vaya con usted en la máquina.
5. Do not allow riders.
6. No entre en el área del rotor mientras el motor está en
marcha.
6. Do not enter rotor area when engine is
running.
7. Nunca exceda 32 km/h (20 MPH) al transportar.
7. Never exceed 20 MPH when transporting.
8. Use hazard flashers when transporting.
8. Use luces intermitentes de aviso cuando viaja con la
máquina.
9. Use drawbar pin with retainer and attach
safety chain.
9. Use el pasador de la barra de tiro con fiador y enganche la
cadena de seguridad.
10. Wear appropriate hearing protection for
prolonged exposure to excessive noise.
10. Use un protector apropiado para los oidos cuando esté
expuesto a ruido excesivo por un tiempo prolongado.
11. Review safety information periodically
prior to use.
11.
Repase la información de seguridad periódicamente
antes del uso.
50030977-B
10 Safety
MAN0506 (Rev. 9/5/2008)
SAFETY & INSTRUCTIONAL DECALS
ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED!
Replace Immediately If Damaged!
DANGER
PELIGRO
DANGER
PELIGRO
ROTATING FLAIL HAZARD
To prevent serious injury or death from
rotating flails:
ROTATING DRIVELINE HAZARD
To prevent serious injury or death from
rotating driveline:
1. Stop engine, remove ignition key, and wait
for moving parts to stop before servicing.
1. Keep all guards in place when operating.
2. Operate only at 1000 RPM.
2. Keep hands and feet away from flails when
engine is running.
3. Keep hands, feet, clothing, and hair away
from moving parts.
3. Keep other people away.
PELIGRO CON EL MOVIMIENTO
ROTATIVO DEL EJE MOTRIZ
Para evitar heridas graves o la muerte a causa
PELIGRO CON LAS CUCHILLAS
CORTADORAS ROTATIVAS
Para evitar heridas graves o la muerte
de la rotación del eje motriz:
causadas por las cuchillas rotativas:
1. Mantenga todos los protectores en su
puesto mientras esté funcionando la
máquina.
1. Pare el motor, quite la llave del encendido
y espere hasta que las piezas móviles
hayan parado antes de dar servicio.
6 - PN 50030978
2. Hágala funcionar únicamente a 1000 RPM.
2. Mantenga las manos y los pies retirados de
las cuchillas estando el motor en marcha.
3. Mantenga retirados de las piezas móviles,
las manos, los pies, la ropa y el pelo.
50030978-A
7 - PN 50030982
3. No permita que otra gente se acerque.
50030982-A
8 - PN 50530138
10 - PN 50530314
9 - PN 50530225
(Safety Decals continued on next page)
MAN0506 (Rev. 9/5/2008)
Safety 11
SAFETY & INSTRUCTIONAL DECALS
ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED!
Replace Immediately If Damaged!
(Safety Decals continued from previous page)
12 - PN 50530728
11 - PN 50530707
14 - PN 50530315
WARNING
ADVERTENCIA
16 - PN 33347
15 - PN 18864
HIGH-PRESSURE FLUID HAZARD
To prevent serious injury or death:
DANGER
1. Relieve pressure on system before
repairing, adjusting, or disconnecting.
2. Wear proper hand and eye protection
when searching for leaks. Use wood or
cardboard instead of hands.
3. Keep all components in good repair.
ROTATING DRIVELINE
CONTACT CAN CAUSE DEATH
PELIGRO DE FLUIDO BAJO
ALTA PRESION
Para evitar heridas graves o la muerte:
KEEP AWAY!
DO NOT OPERATE WITHOUT -
1. Alivie la presión del sistema antes de
hacer repara ciones, ajustes o
desconecciones.
ꢀ All driveline guards, tractor and
equipment shields in place
2. Use protección apropiada en las
manos y en los ojos, cuando revise
para ver si hay fugas. Utilice una tabla
o un cartón en vez de las manos.
ꢀ Drivelines securely attached at both ends
ꢀ Driveline guards that turn freely on
33347E
driveline
18864-C
3. Mantenga todos los componentes en
buen estado.
50530315-A
BE CAREFUL!
Use a clean, damp cloth to clean safety decals.
Avoid spraying too close to decals when using a pressure washer; high-pressure water can enter
through very small scratches or under edges of decals causing them to peel or come off.
Replacement safety decals can be ordered free from your Woods dealer. To locate your nearest
Canada call 1-800-319-6637.
12 Safety
MAN0506 (Rev. 9/5/2008)
OPERATOR SIGN-OFF RECORD
Woods Equipment Company follows the general safety
Do not operate or allow anyone else to operate this
equipment until this information has been reviewed.
Review this information annually, before the season
start-up. Make periodic reviews of the Safety and
Operation sections standard practice for those using
any of your equipment.
standards specified by the American Society of Agri-
cultural and Biological Engineers (ASABE) and the
Occupational Safety and Health Administration
(OSHA) for agricultural equipment.
Anyone who will be operating and/or maintaining the
flail shredder must read and clearly understand all
Safety, Operating, and Service & Maintenance infor-
mation presented in this manual.
Use the following Operator Sign-off Record to verify
that each operator has read and understood the infor-
mation in this manual and has been instructed in the
safe operation of the flail shredder.
.
DATE
OPERATOR’S NAME (PRINT)
OPERATOR’S SIGNATURE
MAN0506 (Rev. 9/5/2008)
Operator Record 13
OPERATION
The Woods Flail Shredder is designed to pick up and
shred crop and plant residue left in the field. Rotational
power to the flails is provided by the tractor PTO.
CAUTION
„ Always comply with all state and local lighting
and marking requirements.
Be familiar with the flail shredder before starting.
The owner is responsible for training operators in the
safe operation of the flail shredder.
„ Always wear relatively tight and belted clothing
to avoid getting caught in moving parts. Wear
sturdy, rough-soled work shoes and protective
equipment for eyes, hair, hands, hearing, and head;
and respirator or filter mask where appropriate.
PRINCIPAL COMPONENTS
„ Safety instructions are important! Read all
attachment and power unit manuals; follow all
safety rules and safety decal information. (Replace-
ment manuals and safety decals are available from
your dealer. To locate your nearest dealer, check
or in the United States and Canada call 1-800-319-
6637.) Failure to follow instructions or safety rules
can result in serious injury or death.
The Woods Flail Shredder consists of a large rotating
tube with swinging steel flails attached. The flails pick
up or strike crop residue or trash and shred it. Rota-
tional power to the drum is provided by the tractor PTO
through a gearbox in the center of the machine.
For removing the center strip of crop residue, an
optional hydraulically driven blade can be installed
under the cover in the center of the machine.
„ Never allow children or untrained persons to
operate equipment.
The flail shredder is designed to be used as a pull-type,
semi-mounted, or 3-point mounted machine.
„
Make sure shields and guards are properly
installed and in good condition. Replace if damaged.
BREAK-IN OF THE FLAIL SHREDDER
„ Keep hands, feet, hair, and clothing away from
equipment while engine is running. Stay clear of all
moving parts.
The following should be observed when operating the
unit for the first time:
NOTICE
„ Never allow riders on power unit or attachment.
■ Before operating the unit in the field, run the
PTO clutch. See . Weasler Modular Friction Clutch
(24K), page 33.
„ Before dismounting power unit or performing
any service or maintenance, follow these steps:
disengage power to equipment, lower the 3-point
hitch and all raised components to the ground,
operate valve levers to release any hydraulic pres-
sure, set parking brake, stop engine, remove key,
and unfasten seat belt.
After operating for 1/2 hour
1. Check all nuts, bolts, and other fasteners. Tighten
to specifications given in the Bolt Torque Chart,
page 63.
„ Do not allow bystanders in the area when oper-
ating, attaching, removing, assembling, or servic-
ing equipment.
2. Tighten wheel bolts to specifications given in the
Bolt Torque Chart, page 63.
3. Check that the flails are in good condition and
„ Keep bystanders away from equipment.
swing freely.
„ Operate tractor PTO at the rpm speed stated in
“Specifications” section.
4. Check oil level in the gearbox. Add oil if needed.
5. Check that the PTO driveline shield turns freely.
6. Lubricate all grease points.
CAUTION
After operating for 5 to 10 hours
„ Always sit in power unit seat when operating
controls or starting engine. Securely fasten seat
belt, place transmission in neutral, engage brake,
and ensure all other controls are disengaged
before starting power unit engine.
1. Repeat Steps 1 through 5 above.
2. Follow regular service schedule as outlined in
Service & Maintenance, page 24.
14 Operation
MAN0506 (Rev. 9/5/2008)
1. Crossmember
2. Rubber belt shield
3. Skid assembly
4. Rubber belt shield
5. Body weldment
6. Flail tube assembly RH
7. Flail tube assembly LH
8. Woods model decal
9. Gearbox
10. Bearing assembly
Figure 1. Flail Shredder Principal Components
___ Inspect all hydraulic lines, hoses, couplers, and
fittings. Tighten, repair, or replace any leaking or
damaged components.
PRE-OPERATION CHECK LIST
(OWNER'S RESPONSIBILITY)
___ Install and secure all guards, doors, and covers.
NOTICE
■ This Pre-Operation Check List is provided for
the operator. It is important to follow for both per-
sonal safety and maintenance of the flail shredder.
___ Check PTO clutch operation (see . Weasler Mod-
ular Friction Clutch (24K), page 33).
CHOOSING THE CORRECT TRACTOR
___ Check all lubrication points and grease as
instructed in Lubrication Service Record, page
27.
To ensure safe and reliable operation of the flail shred-
der, use a tractor with the correct specifications. Use
the following guidelines to select the correct tractor.
___ Use only a tractor of adequate power and weight
to pull the unit. (See chart below.)
1. Horsepower
___ Check that the unit is properly attached to the
tractor. On pull-type unit, be sure there is a
mechanical retainer through the drawbar pin and
the safety chain is installed. On 3-point hitch
units, be sure retainers are used on the mounting
pins.
Use Table 1 on page 16 for selecting the tractor horse-
power class appropriate for your unit’s width.
Increase the horsepower level by 25 percent when
operating in hilly, soft, or wet conditions.
2. Tractor Weight
___ Check oil level in gearbox. Add oil as required.
By following recommendations for tractor horsepower,
the tractor will have sufficient weight to provide stability
for unit during field operation or when transporting.
___ Check that the PTO driveline turns freely and that
the driveline can telescope easily.
When using a 3-point mounted shredder, we recom-
mend that each tractor be equipped with a full comple-
ment of suitcase weights on the tractor front (see
Figure 2 for example). This will provide the required
front weight for turning and extra traction if equipped
with front wheel assist.
___ Check tire pressure. Inflate to specified level.
___ Check flails. Inspect for damage or breakage.
Make sure they swing freely on their mount.
Repair or replace as required.
___ Check condition of cutter blade (if so equipped).
MAN0506 (Rev. 9/5/2008)
Operation 15
6. Drawbar (Pull-Type Models Only)
Table 1: Tractor Horsepower (6-8) vs. Unit Width
The tractor drawbar must be set to provide 16" (406
mm) on 1-3/8 - 21 or 20" (508 mm) 1-3/4 - 20 between
the end of the PTO shaft and the center of the drawbar
pin for all 1000 rpm PTO. See Figure 4. This dimension
will provide the required clearance for the CV (Con-
stant Velocity) joint on the front of the driveline.
Width
15′
Minimum Horsepower
90
20′
120
132
150
162
22′
NOTICE
25′
■ Do not use PTO shaft adapters. They will
change the drawbar dimension and can cause driv-
eline failures.
27′
NOTE: On pull-type models, do not cut driveline.
Upper Top Link Hole
Top Link Assembly
Lower Top Link Pin
Lower 3-Point Pin
Figure 2. Tractor Front Weight
3. 3-Point Hitch
Figure 3. 3-Point Hitch Attachment
The 3-point hitch models require that the tractor be
equipped with a Category II or Category III 3-point
hitch. If the hitch can be converted from one to the
other, use a Category III to provide a wider stance and
more stability.
1000 RPM
16” or 20”
Use the upper top link hole for Category III and the
lower hole for Category II as shown in Figure 3.
For easier attachment, use a quick hitch. If not using a
quick hitch, use optional hitch extension.
4. Hydraulic Requirements when Using Center
Cutter Options
Figure 4. Drawbar Dimension
PTO Driveline Length
The tractor hydraulic system must be capable of 8 gpm
(30 lpm) at 1500 psi (10,335 kPa). Either closed-cen-
tered or open-centered systems can be used.
(3-Point & 2-Point Models Only)
The unit is equipped with a PTO driveline long enough
to fit any tractor and 3-point linkage system.
5. Load Sensing Hydraulics (3-Point Models Only)
The operator is responsible for measuring the dimen-
sions of the driveline through its working range. These
dimensions will indicate if the driveline requires short-
ing to operate on the particular tractor/unit attachment
system. The operator must check dimensions before
using the unit for the first time and each time a different
tractor is used with the unit.
Many newer tractors are equipped with “load sensing”
hydraulics. The operator is responsible for setting the
tractor hydraulic system to provide “float” on the 3-point
hitch. Refer to the tractor manual for specific instruc-
tions.
The “float” feature will allow the unit to follow the
ground contours during operation. This applies to 3-
point mounted machines only.
Use the following procedure when determining drive-
line dimension:
16 Operation
MAN0506 (Rev. 9/5/2008)
ATTACHING SHREDDER TO TRACTOR
1. Place unit on a level, dry area free of debris and
other foreign object.
„ Keep bystanders away from equipment.
1. Clear the area of all bystanders.
„ Keep bystanders away from equipment.
2. Attach the 3-point hitch to the unit but not the PTO
driveline.
„ Connect PTO driveline directly to power unit
PTO shaft. Never use adapter sleeves or adapter
shafts. Adapters can cause driveline failures due to
incorrect spline or incorrect operating length and
can result in personal injury or death.
3. Raise the unit until the tractor PTO and gearbox
shafts are the same height.
4. Measure the dimension between the shaft grooves
on the tractor and implement ends. If this
dimension is less than 34.81 inches, the shaft will
require shortening.
2. Clear the area of bystanders, especially children.
3. Provide enough clearance to back the tractor
safely into the unit.
5. Move the unit to its highest and lowest working
position and measure this dimension again. [The
unit’s shaft can telescope (see Figure 6) before it
has been shortened.]
CAUTION
■
Do not allow anyone to stand between tractor
and unit when backing up to the unit.
6. If required, shorten the shaft to prevent bottoming
out during use. NOTE: An extra inch of
compression space in the shaft can eliminate
bottoming out during use. Measure to make sure.
With Quick Hitch Attachment:
4. Set the height of the 3-point hitch so that quick
hitch claws are lower than the mounting pins.
7. Use an abrasive wheel power saw to cut the male
end of the shaft. Cut the same amount from both
the splined shaft and the safety shield. See Figure
5. Use a file to remove any burrs from the cut end.
5. Make sure 3-point hitch is set in the non-sway
position. See tractor manual for details.
6. Align the claws under the lower and upper mast
mounting pins while backing up.
NOTICE
NOTE: For a Category II hitch, use the bottom
upper mast hole. For a Category III hitch, use the
top upper mast hole.
■ Cut only the male end. Never cut the female end.
8. Never cut more than 9 inches from the male end.
Cutting 1 inch from the male end shortens both the
minimum and maximum lengths by 1 inch.
7. When the claws are under the pins, slowly raise
the 3-point hitch. Make sure each mounting pin
seats in its respective claw.
8. Release the claw retainer locks to secure the
mounting pins in the claws.
9. Check the top link frame. It should be free to slide
in its mounting slots. This movement allows the
unit to follow the ground contour when cresting a
hill or going through a depression.
Figure 5. Cutting the Driveline Shaft
Figure 6. Driveline Dimension
MAN0506 (Rev. 9/5/2008)
Operation 17
Without Quick Hitch Attachment:
1. Back tractor lower 3-point arms between lower
mast plates and align with lower 3-point hole.
2. Place 1-3/4 OD spacer through 3-point arm pivot
(both sides).
3. Push tractor’s 3-point arm to the inside and slide a
1-7/16 OD spacer between to take up the empty
space. Secure with lower 3-point hitch pin
assembly, 1-3/4 OD spacer, and 7/16 x 2 klik pin.
4. Repeat steps 5 and 6 for other side.
Figure 8. Drawbar & Safety Chain
5. Lower the tractor’s top link arm and secure in top
hole of upper mast assembly using spacer, hex
bolt, and lock nut. (See illustration and parts list,
page 48-48.)
Attach PTO Driveline
1. Make sure the driveline telescopes easily and
shields rotate freely.
Pull-Type Model:
NOTICE
■ The drawbar may need repositioning to provide
clearance for the driveline.
1. Use the ratchet (see Figure 7) on top of the hitch to
set the hitch height.
2. Attach the driveline to the tractor by retracting the
locking collar. Slide the yoke over the shaft and
push on the yoke until the lock collar clicks into
position. Make sure the yoke is locked into
position. See Figure 9.
2. Check and set the drawbar dimension.
3. Back the tractor up to the hitch.
4. Use a hardened drawbar pin that provides for a
mechanical retainer, such as a Klik pin.
5. Attach safety chain from hammer strap around the
drawbar or cage to prevent unexpected separation.
Provide sufficient slack for turning.
6. Use the ratchet to transfer the unit’s weight to the
drawbar.
7. Make sure the drawbar is pinned in its center
position.
Figure 9. Locking Collar
Attach Hydraulics (Center Cutter Option)
1. Use a clean cloth to clean hose ends and area
around the couplers on the tractor.
2. Insert the hose male ends into the tractor couplers.
Make sure hoses lock in place.
3. Route hoses along or over the hitch and secure in
position with clips, tape, or plastic ties. Provide
enough slack for turning and lifting.
Figure 7. Attaching to Pull-Type Model
18 Operation
MAN0506 (Rev. 9/5/2008)
„ Keep hands, feet, hair, and clothing away from
equipment while engine is running. Stay clear of all
moving parts.
Raise Stands
1. Use hitch ratchets or 3-point hitch to raise the front
of the machine.
„ Before dismounting power unit or performing
any service or maintenance, follow these steps:
disengage power to equipment, lower the 3-point
hitch and all raised components to the ground,
operate valve levers to release any hydraulic pres-
sure, set parking brake, stop engine, remove key,
and unfasten seat belt.
2. Unpin front frame stands. Raise and pin in their
upper position. See Figure 10.
REMOVING SHREDDER FROM TRACTOR
Reverse the above procedure (Steps 1-17) when
removing unit from the tractor.
„ Never allow riders on power unit or attachment.
„ Do not allow bystanders in the area when oper-
ating, attaching, removing, assembling, or servic-
ing equipment.
„ Inspect and clear area of stones, branches, or
other hard objects that might be thrown, causing
injury or damage.
„
Operators must be instructed in and be capable
of the safe operation of the equipment, its attach-
ments, and all controls. Do not allow anyone to
operate this equipment without proper instructions.
„ Keep bystanders away from equipment.
„ Operate tractor PTO at the rpm speed stated in
“Specifications” section.
Figure 10. Parking Stand
FIELD OPERATION
CAUTION
The Woods Flail Shredder is designed with the flexibil-
ity to operate well in almost any kind of crop and terrain
conditions. However, the operator is responsible for
being familiar with all operating and safety procedures
and following them. Each operator should review this
Field Operation section at the start of the season and
as often as required to be familiar with the unit.
„ Always sit in power unit seat when operating
controls or starting engine. Securely fasten seat
belt, place transmission in neutral, engage brake,
and ensure all other controls are disengaged
before starting power unit engine.
„ Always comply with all state and local lighting
and marking requirements.
Operators should also review the PRE-OPERATION
CHECK LIST, page 15, and Attaching Shredder to
Tractor, page 17.
„ Always wear relatively tight and belted clothing
to avoid getting caught in moving parts. Wear
sturdy, rough-soled work shoes and protective
equipment for eyes, hair, hands, hearing, and head;
and respirator or filter mask where appropriate.
PREPARING FOR OPERATION
„ Safety instructions are important! Read all
attachment and power unit manuals; follow all
safety rules and safety decal information. (Replace-
ment manuals and safety decals are available from
your dealer. To locate your nearest dealer, check
or in the United States and Canada call 1-800-319-
6637.) Failure to follow instructions or safety rules
can result in serious injury or death.
1. Pull into the field and position the unit in a level
area.
2. Lower into operating position.
3. 3-Point hitch models: Set the 3-point so the quick
hitch is vertical and the floating upper mast is
forward.
Flail Height
„ Never allow children or untrained persons to
operate equipment.
Set the unit to give a flail height of at least 3 to 6
inches (75 to 150 mm) above the ground. This will
minimize the amount of stones and dirt picked up by
„
Make sure shields and guards are properly
installed and in good condition. Replace if damaged.
MAN0506 (Rev. 9/5/2008)
Operation 19
the flails under all operating conditions. (See Balance
Statement, page 5.)
4. 3-Point models only: Be sure the floating mast is
free to slide in its mounting frame to allow the
machine to follow ground contours. Refer to Figure
13.
NOTE: To avoid unnecessary wear on knives and
related parts, never set the unit lower than the recom-
mended setting. (See Balance Statement, page 5.)
Floating Top Mast
7109
Figure 11. 3-Point Hitch Models
7111
Figure 13. Free-Float Position
SET OPERATING HEIGHT
3-Point Hitch Models
FLAIL KNIVES
The shredder is factory equipped with “L” or cup type
flails. The two types are interchangeable.
Use the ratchet on the rockshaft mount to set the unit
height.
Pull-Type Models
“L” Flails
Use the ratchets or cylinders on the hitch and rockshaft
mount to set the unit height.
“L” flails (Figure 15) work best when trash or crop resi-
due is standing.
Cup Flails
Cup flails (Figure 16) can pick up material from the
ground and work best in matted trash conditions.
The standard cup flail is 11 inches (279 mm) long and
is used for most applications. Optional 7 and 9 inch
(177 and 228 mm) flails are available to match the tip
position to ground contour.
Attach optional cup flails as follows, making sure that
knives at 180° match (see Figure 14) (see Balance
Statement, page 5):
Figure 12. Pull-Type Models (Ratchet)
1. Leave standard flails located between the rows.
3-Point & 2-Point Hitch Models
2. Remove others and install shorter flails to follow
ground contour. Be sure to mount the same size
flails on opposite sides of the tube. Measure the
row spacing and flail position carefully to minimize
ground contact. See page 36 and page 37.
1. Set lower 3-point arms in the free-float position.
2. Set the hitch in the non-swing position.
3. Set the hydraulic system to allow the 3-point to
float. Refer to tractor manual for instructions.
20 Operation
MAN0506 (Rev. 9/5/2008)
.
Setting Outer Trailing Wheels
(Casters & Struts)
Normally, wheels are set to track in the row centers,
between the raised seed beds. Tire position will deter-
mine flail height, but depth of furrow is also a factor in
setting flail height. In some conditions the furrow
between the seed beds is deeper on the ends, where
irrigation waters enter the field. As furrows change
depth, flail height will change.
To compensate for the depth change, move the trailing
wheels against the side of the outer seed bed (see Fig-
ure 17). The wheels will then tend to climb up the side
of the seed bed and prevent the flails from hitting the
top of the bed.
Figure 14. Optional Flail Contour
Set the flail height after the wheels have been moved
against the seed bed.
Figure 17. Wheel Position
Figure 15. “L” Flails
STARTING THE TRACTOR
1. Run tractor engine at low idle.
2. Slowly engage PTO control to start the shredder.
3. Slowly bring tractor engine to rated PTO speed.
Never exceed rated speed.
STOPPING THE TRACTOR
„ Before dismounting power unit or performing
any service or maintenance, follow these steps:
disengage power to equipment, lower the 3-point
hitch and all raised components to the ground,
operate valve levers to release any hydraulic pres-
sure, set parking brake, stop engine, remove key,
and unfasten seat belt.
Figure 16. Cup Flails
Setting Flail Height
1. Be sure wheels are set to follow in the center of
furrow row. Set flails 3 to 6 inches (75 to 150
mm) above the ground. (See Balance Statement,
page 5.)
1. Slowly decrease engine speed to low idle.
2. Disengage center cutter’s hydraulic system (if so
equipped). Never approach unit until the blade has
stopped turning.
2. Align the unit with the working area on or between
rows on flat farming.
3. Slowly disengage PTO clutch. The overrunning
clutch will allow the shredder to freewheel down.
3. 3-Point Models: Set the 3-point hitch so the
wheels carry only a small portion of the unit’s
weight and act more as stabilizing wheels. See
tractor manual for setting hitch.
4. Restart the unit only after the drums quit turning.
The PTO will not need to be disengaged to lift the
unit on the ends or while turning.
MAN0506 (Rev. 9/5/2008)
Operation 21
CV joint angle should not exceed 80 degrees in either
operating or standstill condition of the driveline. Larger
angles will damage the joint.
HAZARD AREA
The angle should never exceed 35 degrees when the
driveline is under full load.
„ Make certain all movement of equipment com-
ponents has stopped before approaching for ser-
vice.
NOTICE
■ Disengage PTO when making sharp turns.
Stay away from front, side, and rear of unit while it is
running. Flails can pick up stones, sticks, wire, and
other debris and throw it out with enough force to
severely injure bystanders.
Keep out of shaded area shown in Figure 18.
Shut down unit and wait for moving parts to stop before
approaching.
KEEP OUT
OF
Figure 19. CV Joint Angles
CLEANING
After Each Use
Figure 18. Hazard Area
●
●
●
Remove large debris such as clumps of dirt, grass,
crop residue, etc. from machine.
GROUND SPEED
Travel speed can vary between 3 and 8 mph (5 and 13
kmph) depending on the bulk of residue and terrain
conditions. The operator is responsible for noting the
condition of the work, setting the speed to obtain a
quality shredding job, and maintaining control of the
unit.
Inspect machine and replace worn or damaged
parts.
Replace any safety decals that are missing or not
readable.
Periodically or Before Extended Storage
●
Clean large debris such as clumps of dirt, grass,
crop residue, etc. from machine.
Speed may be increased if shredding quality is good.
Decrease speed if trash is left standing or if some is not
picked up.
●
Remove the remainder using a low-pressure water
spray.
TURNING
1. Be careful when spraying near scratched or torn
safety decals or near edges of decals as water
spray can peel decal off surface.
3-Point Mounted Units:
2. Be careful when spraying near chipped or
Always raise the unit slightly to lift rear wheels off the
ground before turning. This will eliminate side loads on
the wheel assembly, unless unit is equipped with caster
wheels.
scratched paint as water spray can lift paint.
3. If a pressure washer is used, follow the advice
of the pressure washer manufacturer.
●
●
Inspect machine and replace worn or damaged
parts.
Pull-Type Units:
The front universal is equipped with a CV (Constant
Velocity) joint to allow for turning. Although the CV joint
allows for sharper turns than a regular driveline, it does
have some limitations. Refer to Figure 19.
Sand down scratches and the edges of areas of
missing paint and coat with Woods spray paint of
matching color (purchase from your Woods
dealer).
22 Operation
MAN0506 (Rev. 9/5/2008)
●
Replace any safety decals that are missing or not
readable (supplied free by your Woods dealer).
See Safety Decals section for location drawing.
12. Do not allow children to play on or around the
stored unit.
OPTIONAL EQUIPMENT
STORAGE
RUBBER FLAPS
All units are equipped with front shield flaps (Figure 20)
along the front of the frame. The shield flaps stop or
deflect trash, stones, or other debris picked up by the
flails.
„ Block equipment securely for storage.
„ Keep children and bystanders away from stor-
age area.
Be sure the shield flaps are in good condition for opera-
tion. Replace if damaged, torn, or missing.
At the end of the season, the shredder should be thor-
oughly inspected and prepared for storage. Repair or
replace any worn or damage components to prevent
unnecessary down time at the beginning of the next
season.
ADDITIONAL REAR WHEELS
Additional rear wheels (Figure 21) should be installed
on machines 18 feet or wider. They provide extra flota-
tion and stability for wide units and are available from
your dealer or the factory.
To ensure a long, trouble-free life, prepare the unit for
storage by carrying out the following procedure:
1. Clear the area of bystanders, especially children.
2. Thoroughly wash the unit, using a pressure washer
to remove all dirt, mud, debris, and residue. See
Cleaning instructions on this page.
3. Inspect the flails and rotors for damage or
entangled material. Remove entangled material.
Repair or replace damaged parts.
4. Inspect all hydraulic hoses, lines, couplers, and
fittings. Tighten all loose fittings. Replace any hose
that is cut, nicked, abraded, or separating from the
crimped end of a fitting.
3141506
Figure 20. Optional Rear Wheels
5. Change gearbox oil.
BED CONES
3-POINT UNITS ONLY
6. Lubricate all grease fittings. Make sure all grease
cavities have been filled with grease to remove any
water residue from pressure washing.
For some operations you may want to pack hills. Mount
bed cones (Figure 21) directly over the row in place of
rear wheels.
7. Touch up all paint nicks and scratches to prevent
rust.
8. Move to storage area. Select a dry area free of
debris. Store in an area away from human activity.
9. Unhook from tractor (see Removing Shredder from
Tractor, page 19).
10. Place safety stands or large blocks under the
frame to take the load off the tires. NOTE: Do not
deflate tires.
11. If the unit cannot be placed indoors, cover with a
waterproof tarpaulin and tie securely. Store away
from human activity.
Figure 21. Optional Bed Cones
MAN0506 (Rev. 9/5/2008)
Operation 23
SERVICE & MAINTENANCE
grease with extreme pressure (EP) performance.
An SAE multi-purpose lithium-based grease is also
acceptable.
„ Before dismounting power unit or performing
any service or maintenance, follow these steps:
disengage power to equipment, lower the 3-point
hitch and all raised components to the ground,
operate valve levers to release any hydraulic pres-
sure, set parking brake, stop engine, remove key,
and unfasten seat belt.
2. Gearbox Oil
Use an SAE 85W90 gear oil for all operating
conditions. Capacity: 2-1/2 U.S. quarts (110 oz.).
Storing Lubricants
Your unit can operate at top efficiency only if clean
lubricants are used. Use clean containers to handle all
lubricants. Store them in an area protected from dust,
moisture, and other contaminants.
„ Before working underneath, read manual
instructions, securely block up, and check stability.
Secure blocking prevents equipment from drop-
ping due to hydraulic leak down, hydraulic system
failure, or mechanical component failure.
„ Keep all persons away from operator control
area while performing adjustments, service, or
maintenance.
GREASING
NOTE: Use the Lubrication Service Record, page 27 to
keep a record of all scheduled maintenance.
1. Use a hand-held grease gun for all greasing.
„ Do not handle knives with bare hands. Careless
or improper handling may result in serious injury.
2. Wipe grease fitting with a clean cloth before
greasing to avoid injecting dirt and grit.
„
Make sure shields and guards are properly
installed and in good condition. Replace if damaged.
3. Replace and repair broken fittings immediately.
4. If fittings will not take grease, remove and clean
thoroughly. Also clean lubricant passageway.
Replace fitting if necessary.
CAUTION
„ Always wear relatively tight and belted clothing
to avoid getting caught in moving parts. Wear
sturdy, rough-soled work shoes and protective
equipment for eyes, hair, hands, hearing, and head;
and respirator or filter mask where appropriate.
LUBRICATION SCHEDULE
NOTE: Recommendations are based on normal oper-
ating conditions. Severe or unusual conditions may
require more frequent lubrication or oil changes. Refer
to Figure 23.
„ Make certain all movement of equipment com-
ponents has stopped before approaching for ser-
vice.
Daily or every 8 hours of operation
LUBRICANTS
PTO Driveline Lubricate daily or every 8 hours of oper-
ation (every 4 hours if U-joints run at angles). See Fig-
ure 22 for lubrication points.
1. Grease
Use an SAE multi-purpose high temperature
24 Service & Maintenance
MAN0506 (Rev. 9/5/2008)
Figure 22. PTO Driveline Lubrication Points
A. Daily or 8 hours
B. 25 hours
C. 40 hours
D. Check Daily/Change Annually
Figure 23. Lubrication Points
(Rev. 1/24/2011)
MAN0506 (Rev. 9/5/2008)
Service & Maintenance 25
Daily or every 8 hours of operation
Every 40 hours of operation
1. Lubricate PTO U-joints and over-running clutch.
1. Lubricate rotor drive couplers next to the couplers
on underside of unit and inside of flail tube (use
hole in flail tube to access grease fitting, 2
locations).
2. Check gearbox daily or every 8 hours of operation.
See Figure 24 for gearbox oil fill location.
2. Grease the drive hubs with 10 to 20 pumps. You
may use extra grease only on drive hubs.
Annually
1. Change gearbox oil. Refill with SAE 85W90 gear
oil. Capacity: 2-1/2 U.S. quarts (110 oz.). See
Figure 27.
ROTOR
DRIVE HUB
7109
Figure 24. Gearbox Oil Fill Location
Every 25 hours of operation
1. Lubricate PTO driveline telescoping section (one
location, Position B, Figure 23).
GEARBOX
OIL DRAIN
2. Lubricate rotor end bearings. See Figure 25.
3. Lubricate wheel rockshaft bearings (3 to 5
Figure 27. Gearbox Oil Drain Location
locations). See Figure 26.
2. Repack wheel bearings. See Figure 28.
7126Z
Figure 28. Wheel Bearings
7123Z
3. Lubricate ratchets as necessary (2 locations each
Figure 25. Rotor End Bearing
ratchet). See Figure 29.
Lubrication Point
7114Z
7104Z
Figure 26. Wheel Rockshaft Bearing
Lubrication Points
Figure 29. Ratchet Lubrication Points
(Rev. 1/24/2011)
26 Service & Maintenance
MAN0506 (Rev. 9/5/2008)
LUBRICATION SERVICE RECORD
NOTE: See page 24 through page 27 for details. Copy
this page to continue service record.
HOURS OF
SERVICE
SERVICED BY
10 Hours or daily
L PTO Driveline (8)
L PTO Driveline telescope
section
L U-Joint (1)
L Overrunning clutch (1)
Gearbox oil level
✔
25 Hours
L Rotor end bearings
L Wheel mounting tube
bearings
40 Hours
L Rotor inner bearings (2)
Annually
C Gearbox oil
R Wheel bearings
L Ratchets
GEARBOX OIL LEAKAGE
NOTICE
■ DO NOT OVERFILL. Lab tests have proven that
overfilling the gearbox can dramatically increase
the gearbox operating temperature. In extreme
cases this can overheat the oil, reducing its lubri-
cating and cooling properties, and eventually
cause shaft seals to deteriorate and fail. Over-
heated oil has an obvious burnt smell; drain it and
refill with new oil. Overfilling gearbox oil can void
the warranty.
NOTICE
■ Major oil leakage from the gearbox shaft seal
area is not acceptable and could cause the gearbox
to fail due to lack of lubrication and cooling. It is
the operator’s responsibility to check the gearbox
oil level per the Lubrication Service Table.
Before checking gearbox oil level, shut down the
shredder for a couple of hours to allow the oil to drain
back into the reservoir for the most accurate reading.
Proper oil level should be between the full and add
lines on dipstick. When oil is needed, add through the
dipstick tube.
The gearbox should not require frequent servicing of
oil. It is not designed to consume or lose large amounts
of oil. If oil needs to be added frequently, troubleshoot-
ing the cause is required (see section below).
MAN0506 (Rev. 9/5/2008)
Service & Maintenance 27
Gearbox leakage & Troubleshooting
Woods dealer. Consult with Woods Technical
Service for further details, rebuild
recommendations, or warranty questions.
Some gearbox oil leakage may be acceptable if:
1. Oil covers less than a 3-inch diameter circle around
CHANGING GEARBOX OIL
the shaft seal area (see Figure 30).
2. Oil covers less than a 4-inch diameter circle around
Although gearbox oil never wears out, dust, dirt, and
moisture can enter through the breather during opera-
tion. These contaminants must be removed once a
year to ensure a long life for working components. In
very dusty or dirty conditions, change the oil twice a
year.
the dipstick tube (see Figure 30).
If oil leakage covers an area larger than that described
in 1 and 2, do the following:
1. Properly check oil level. If low, properly service.
1. Clear area of bystanders, especially children.
2. Clean oily area of gearbox. Use a degreaser to
remove all oil from outside surface of gearbox.
2. Shut off tractor, place all controls in neutral, set
parking brake, remove key, and wait for all moving
parts to stop.
3. Closely monitor gearbox for 10 hours of operation.
Check and service oil every 30 minutes or as
needed to ensure operation does not occur with oil
below the add mark.
3. Raise the unit to provide access to underside.
Place safety stands or large blocks under frame.
4. If after 10 hours of operation, oil covers less than
the area described in 1 & 2 above, seepage is
considered to be acceptable.
4. Disconnect PTO driveline and hydraulic lines.
5. Place a pan under drain plug. Remove drain plug
5. If after 10 hours of operation, oil covers more than
the area described in 1 & 2 above, this seepage is
considered to be unacceptable leakage.
and dipstick plug (see Figure 31).
6. Allow gearbox to drain for 10 minutes.
6. Gearboxes with unacceptable leakage should be
rebuilt, replacing old seals and worn parts with new
seals and parts. Gearbox rebuild and seal
replacement parts are available through your local
NOTE: To remove the most contaminants, drain oil
when gearbox is hot.
Figure 30. Acceptable Oil Leakage
28 Service & Maintenance
MAN0506 (Rev. 9/5/2008)
2. Shut off tractor, place all controls in neutral, set
parking brake, remove key, and wait for all moving
parts to stop.
3. Use a jack with sufficient capacity to lift the frame.
4. To determine wheel spacing, measure from the
center line of the unit. Mark positions on the frame.
5. Lift frame until wheels have cleared the ground.
6. Place safety stands or large blocks under the
frame.
7. Loosen mounting bolts on one wheel assembly.
DRAIN PLUG
8. Slide assembly along the frame tube to new
position (see Figure 33).
Figure 31. Drain Plug (Underside of Unit)
7. Re-install and tighten drain plug.
9. Tighten mounting bolts to specified torque level.
8. Dispose of used oil in an approved container.
9. Add SAE 85W90 gear oil through the dipstick
cover. Use the dipstick to check the oil level (Figure
32) and add oil accordingly.
10. Re-install and tighten fill plug.
11. Reconnect PTO driveline and hydraulic lines.
12. Remove blocks or safety stands.
Figure 33. Positioning Wheel Assembly
10. Remove safety stands or blocks.
11. Lower and remove jack.
12. Repeat with other wheel assembly.
REPLACING FLAIL KNIVES
Figure 32. Dipstick Location
„ Do not handle knives with bare hands. Careless
or improper handling may result in serious injury.
RATCHET HEIGHT ADJUSTMENT
Mechanical ratchets provide height setting for the unit.
To set ratchets, follow this procedure:
■ Read Balance Statement, page 5, before replac-
ing any knives.
1. Clear the area of bystanders, especially children.
The flail knives in pairs swing on a hardened bushing,
designed to reduce wear, and are sandwiched
between two steel spacers. The hardened bushing is
bolted to the clip with a 1/2" NC carriage bolt and a
flange lock nut.
2. Turn the turnbuckle to achieve the desired ratchet
length (see Figure 32). Repeat Step 2 with other
ratchets.
WHEEL SPACING
1. Clear the area of any bystanders.
The rear wheels can be adjusted for alignment with
crop rows.
2. Shut off tractor, place all controls in neutral, set
parking brake, remove key, and wait for all moving
parts to stop.
1. Clear the area of bystanders, especially children.
MAN0506 (Rev. 9/5/2008)
Service & Maintenance 29
3. Disconnect driveline and hydraulic lines from the
tractor.
4. Place safety stands or large blocks under the
frame.
5. Loosen and remove the worn flail and its opposite
on the other side of the rotor. Discard worn flails
and their mounting hardware.
6. Replace with new flails and mounting hardware
(see Figure 34).
Figure 35. Front Rubber Shield Flaps
4. Replace damaged flap with new flap and secure
with correct hardware.
NOTE: Use only genuine Woods parts when replacing
flaps.
SERVICING ROTORS (FLAIL TUBES)
„ Do not handle knives with bare hands. Careless
or improper handling may result in serious injury.
Figure 34. Flail Replacement
NOTICE
■ Any excessive vibration caused by worn or
missing knives or damaged drive components can
cause damage to the shredder and personal injury.
Excessive vibration can also be transmitted
through the hitch mounts and PTO to the tractor
resulting in tractor damage.
■ To maintain rotor balance, always replace oppo-
site (180°) pairs of flails and mounting hardware.
7. Tighten flail mounting flange lock nut.
8. Replace additional worn flails following step 5 and
step 6.
■ Once field operation has been started, it is the
responsibility of the owner/operator to monitor and
maintain acceptable rotor balance. Refer to Bal-
ance Statement, page 5, for details.
9. Remove safety stands or blocks from under frame.
10. Lower unit and remove jack.
11. Attach driveline and hydraulic line to tractor.
NOTICE
12. Refer to Balance Statement, page 5, for balance
issues.
■ Read Balance Statement, page 5, before replac-
ing any knives.
REPLACING RUBBER SHIELD FLAPS
Refer to Replacing Flails, page 29, for knife or knife
component replacement.
Rubber shield flaps on the front of the unit deflect or
prevent stones or debris from being ejected when oper-
ating unit. Replace if damaged or missing to provide a
safe work environment. To replace, follow this proce-
dure:
The Woods Center Drive Flail Shredder has been
designed for durability when shredding any type of
crop. Some operating conditions will shorten the life of
the shredder or components. These include operating
too low to the ground or in frequent contact with the
ground, and contact with large rocks or other foreign
objects. Over time, some types of soils and crops can
cause wear or damage to rotor components and affect
rotor balance, leading to increased vibration. Contin-
ued operation with excessive vibration can damage the
shredder, requiring rotor service, removal, or replace-
ment.
1. Clear the area of bystanders, especially children.
2. Lower the unit to the ground, place all controls in
neutral, shut off engine, set park brake, remove
key, and wait for all moving parts to stop before
dismounting.
NOTE: For 3-point hitch units, unhook to gain access
to center flaps.
3. Remove 3/8" nut, washer and carriage bolt from
each worn flap. (Replace any worn or damaged
hardware. See page 48 for hardware sizes.)
Factory balanced spare replacement rotors are avail-
able through your local Woods dealer. Contact Woods
30 Service & Maintenance
MAN0506 (Rev. 9/5/2008)
Technical Service for re-balance options or further
details.
LOCKING COLLAR SET SCREW
LOCKING COLLAR
Follow the procedure below if rotor removal or replace-
ment is required.
SHAFT
FOR REMOVAL: TAP
CAUTION
WITH A HAMMER AND
PUNCH AFTER LOOSENING
SET SCREW.
„ Use a suitable lifting device of sufficient capac-
ity. Use adequate personnel to handle heavy com-
ponents.
FOR INSTALLATION:
REVERSE PROCEDURE
MAN0506003
1. Clear the area of any bystanders.
Figure 36. Locking Collar
2. Shut off tractor, place all controls in neutral, set
parking brake, remove key, and wait for all moving
parts to stop.
Replacing Components
1. Place new stud bolts into gearbox using Loctite®
3. Remove PTO driveline from the shredder.
4. Fully disconnect the shredder from the tractor.
5. Remove wheel arms (casters or struts).
No. 271 or equivalent.
2. Remount gearbox. The gearbox oil dipstick should
protrude out the top panel of the shredder for
checking and servicing. Reinstall the nuts and lock
washers securing the top of the gearbox to the
shredder gearbox mount plate and torque to
specifications in Bolt Torque Chart, page 63.
6. Use a hoist, crane, or frame of sufficient capacity to
raise the front of the unit and allow the back of the
unit to rest on a solid surface (blocks).
7. Leave lifting device attached while working on
3. Remount the crossmember securing the bottom of
the gearbox and torque to specifications in Bolt
Torque Chart, page 63.
rotors to prevent tipping.
Removing Components
4. Install drive couplings and reapply new grease
Refer to Replacing Flails, page 29, for knife or knife
component replacement.
around entire O-ring and gear teeth surfaces.
5. Install rotors (flail tubes) in the opposite fashion as
removal. Position rotors with each end supported
by a crane or hoist so that it is aligned with the gear
coupling and gearbox output shaft center lines.
The bearing (stub shaft) end of the rotor will
protrude out of the hole in the end sheet.
Refer to Servicing Rotors, page 30, before proceeding
with these steps.
1. Follow steps in the previous section to prepare and
position shredder. Support each end of the rotor
(flail tube) to be removed with a crane or hoist.
6. With gentle care not to damage gear coupler teeth
or O-ring, provide pressure to align gear teeth and
slide the rotor back into its original position.
2. Remove bearing locking collar (see Figure 36).
3. Remove the six bolts holding the bearing plate to
NOTE: When re-installing rotors, the gear coupling
grease fitting will need to be temporarily removed
to allow for air to purge from the coupler assembly
during installation. After successful installation,
reinstall grease fitting and re-service.
the body assembly.
4. Slide rotor out to disengage from the center drive
coupling.
5. Thoroughly clean and inspect gearbox drive
couplings for wear and replace if any wear is
detected. Also inspect the rubber O-ring for wear or
tears and replace if any wear or tears are detected.
7. Reinstall bearing plate assembly and bolts, and
apply appropriate torque.
8. Reinstall bearing locking collar and tighten (see
6. Remove crossmember from the underside of the
shredder, providing access for the removal of the
gearbox.
Figure 36).
NOTICE
■ If removing rotor drive coupling, use Loctite No.
271 or equivalent and special high collar lock
washers to keep bolts from loosening.
7. Remove gearbox, if damaged. This will require
removal of the second rotor (repeat steps 1-5
above).
MAN0506 (Rev. 9/5/2008)
Service & Maintenance 31
REPLACING STUB SHAFT
1. Remove rotor (see Servicing Rotors (Flail Tubes),
page 30).
2. Remove three 1/2 x 2-1/2 hex bolts in taper lock
hub and re-install bolts in three threaded holes
(see Figure 38).
3. Tighten bolts evenly to release taper lock hub from
stub shaft. NOTE: You may have to give a sharp
blow directly to each bolt head to help the hub
disengage.
4. Unscrew stub shaft from the rotor tube.
Figure 37. Rotor Direction of Rotation
5. Install new stub shaft, reversing Steps 1-3.
Figure 38. Stub Shaft Assembly
4. Attach the driveline to the tractor PTO. Stand clear
SERVICING WEASLER MODULAR
FRICTION CLUTCH
of the unit.
5. Start tractor. Engage PTO clutch and run for a few
Tools Required
seconds or until clutch visibly smokes.
• 3/4" Socket wrench
6. Disengage PTO. Shut off tractor. Disconnect
• 8" Minimum C-clamps (2)
• 1/4" Hex Allen wrench
• Regular screwdriver or punch
• Duct tape or locking pliers with 3" throat minimum
• Hammer
driveline from the tractor.
7. Tighten all bolts on the outside diameter of the
clutch until the compression plate is tight against
the housing.
• 1/2" sq. to 1" sq. bar x 9"
• Scale or Vernier
8. Grease the fitting on the yoke, using a multi-
purpose high-temperature EP grease or an
equivalent lithium grease.
Breaking In the Clutch (Run In)
9. For an integral overrunning clutch, make sure
NOTE: All new clutches must be broken in (Run in) and
any clutch that has not been used for approximately 60
days.
clutch turns freely in one direction.
Removing the Driveline
1. Shut off tractor and disengage PTO.
1. Shut off tractor and disengage PTO.
2. Disconnect driveline from the tractor PTO shaft.
2. Disconnect driveline from PTO shaft.
3. Loosen the bolts on the outside diameter of the
clutch until all bolts are just loose, then tighten all
bolts 1/2 turn.
3. Remove the bolt (21K) or clamp (24K) that
attaches the clutch to the shredder’s input shaft.
32 Service & Maintenance
MAN0506 (Rev. 9/5/2008)
NOTE: The shaft is heavy. Grasp the clutch firmly
Inspection
with both hands and slide off the input shaft.
1. Inspect the steel parts for wear and replace if
necessary.
Rebuilding Friction Pack
2. Inspect the yoke/hub for looseness. If there is more
than .03 end play, replace.
Disassembly
3. Using screwdriver, scrape any hardened grease
1. Position clutch and universal joint assembly on a
from the overrunning key pockets.
bench so that end is accessible.
2. Remove the long bolts on the outside of the
Assembly
housing that hold the friction pack together.
1. Using a multi-purpose high-temperature EP grease
or equivalent lithium grease, inject one grease gun
pump into each key pocket. Evenly wipe two more
pumps over the overrunning surface.
3. Remove the plate(s) and all internal components.
Leave the yoke/hub intact.
4. Discard friction discs.
2. Press a new leaf spring into each pocket. The ends
5. If rebuilding the overrunning clutch, refer to
Rebuilding Overrunning Clutch, page 33,
beginning with Step 2.
should touch the bottom of the pockets.
Inspection
1. Inspect the steel and iron parts for wear, warping,
or cracks, and replace if necessary.
2. Inspect the yoke/hub for looseness. If there is more
than.03 end play, replace.
3. Clean any rust or dust from the plate surfaces with
a wire brush or steel wool.
Assembly
1. Place one new friction disc, then separator plate,
then second friction disc into housing.
Figure 39. Weasler Modular Friction Clutch (24K)
2. Add the pressure plate so that the flat surface rests
on the friction disc. NOTE: The tangs on the plate
must fall into the reliefs in the housing.
3. Add new keys. With one hand, hold the two keys in
the pockets.
4. Slide the collar onto the hub, orienting collar
3. Add the disc spring so that its inside diameter
correctly.
contacts the fins of the pressure plate.
5. Add washer.
4. Assemble the compression plate and all the long
bolts. Make sure all nuts rest in their pockets.
6. Install retaining ring.
5. Tighten all long bolts to 30 lbs-ft.
7. Make sure clutch spins freely and only in correct
direction.
Rebuilding Overrunning Clutch
8. Reassemble friction pack.
Disassembly
MOUNTING CLUTCH TO SHREDDER
1. Remove the four bolts that secure the friction pack.
1. Mount and bolt the clutch hub onto the shredder
input shaft. Make sure shaft and clutch grooves
line up.
Remove the friction pack.
2. Using screwdriver and pliers, remove the retaining
ring that holds the overrunning clutch together.
2. Re-install any shielding that was moved or
removed.
3. Slide the collar and washer off the clutch hub,
noting the orientation of the collar for reinsertion.
3. Run the clutch before using. Refer to Breaking In
4. Remove and discard the keys and leaf springs.
the Clutch (Run In), page 32.
MAN0506 (Rev. 9/5/2008)
Service & Maintenance 33
NOTES
34 Service & Maintenance
MAN0506 (Rev. 9/5/2008)
TROUBLESHOOTING
The Woods Flail Shredder uses swinging flails to pick up and shred crop residue left in the field. It is a simple and reli-
able system that requires minimal maintenance.
The following table lists problems, causes, and solutions that you may encounter. If you encounter a problem that is dif-
ficult to solve even after reading through this table, please call your local Woods dealer. When calling, please have this
manual and your unit’s serial number ready.
PROBLEM
CAUSE
Poor wheel spacing
SOLUTION
Shredder doesn’t track
Set wheels in center of crop rows.
3-Point not set
Set 3-point hitch in non-sway
position.
Shredder not level
Irrigation furrows not even
Level shredder (see Set Operating
Height, page 20).
Set wheels against seed bed (see
Setting Outer Trailing Wheels
(Casters & Struts), page 21).
Shredder doesn’t follow
ground contour
3-Point not set
Set 3 point in float position.
See tractor manual to set Load
Sensing hydraulic system.
Shredder too high
Set shredder closer to ground.
Set wheels against seed bed.
Irrigation furrows not even
Driveline doesn’t telescope.
Shredder vibrates
Remove, disassemble, and clean
telescoping joint.
Rotor out of balance
Replace damaged or broken flails
and flails 180 degrees opposite.
Check for missing balance weights or
rebalance.
Debris is being thrown out
from under shredder
Shredder set too low
Raise shredder.
Knives excessively worn
Rubber shields missing
Traveling too fast
Replace knives.
Replace flaps immediately.
Slow travel speed.
Lower shredder.
Crop residue is being left
Shredder too high
Improper flails
Change flails.
Crop residue strip left in shredder
center
Add center cutter or divider.
MAN0506 (Rev. 9/5/2008)
Troubleshooting 35
WORKSHEET FOR CONTOUR FLAIL PATTERNS
36 Contour Flail Patterns
MAN0506 (Rev. 9/5/2008)
WORKSHEET FOR CONTOUR FLAIL PATTERNS
24’
MAN0506 (Rev. 9/5/2008)
Contour Flail Patterns 37
ASSEMBLY
After the unit has been leveled for a couple of hours,
check oil level and service through the dipstick/filler
tube as required.
DEALER SET-UP INSTRUCTIONS
„ Do not allow bystanders in the area when oper-
ating, attaching, removing, assembling, or servic-
ing equipment.
„ Do not handle knives with bare hands. Careless
or improper handling may result in serious injury.
„ Keep hands and body away from pressurized
lines. Use paper or cardboard, not hands or other
body parts to check for leaks. Wear safety goggles.
Hydraulic fluid under pressure can easily penetrate
skin and will cause serious injury or death.
„ Make sure that all operating and service person-
nel know that if hydraulic fluid penetrates skin, it
must be surgically removed as soon as possible by
a doctor familiar with this form of injury or gan-
grene, serious injury, or death will result. CON-
TACT A PHYSICIAN IMMEDIATELY IF FLUID
ENTERS SKIN OR EYES. DO NOT DELAY.
Figure 40. Dipstick Shipping Plug Removal
WHEEL ASSEMBLY
„ Check that all hardware is properly installed.
Always tighten to torque chart specifications
unless instructed otherwise in this manual.
1. Raise the rear of the unit.
2. Place safety stands or large blocks under frame.
3. Measure the wheel spacing from the center of the
unit. Mark the frame (rockshaft).
CAUTION
4. Install the wheel assembly to the rockshaft (Figure
41). If equipped with caster wheels, verify that
there is enough clearance for casters to rotate
without hitting each other. Failure to do so will
result in tire damage.
„ Always wear relatively tight and belted clothing
to avoid getting caught in moving parts. Wear
sturdy, rough-soled work shoes and protective
equipment for eyes, hair, hands, hearing, and head;
and respirator or filter mask where appropriate.
5. Tighten mounting bolts to their specified torque.
„ Use a suitable lifting device of sufficient capac-
ity. Use adequate personnel to handle heavy com-
ponents.
1. Open the crate and cartons containing the
attaching components and mounting hardware.
2. Use the packing list to check that all parts have
been shipped.
For Some Models Shipped on End
Units that stand on their aft ends during shipping have
a dipstick shipping plug installed in the gearbox dipstick
tube to prevent leakage during shipping.
Figure 41. Wheel Assembly Installed
NOTICE
3-POINT UNITS
■
For units shipped on aft end, the dipstick ship-
6. Attach floating upper mast (1) to shredder using
two hardened bushings, 1 x 5" hex bolts, lock nuts,
and four 3/4 x 3" spacers. See parts list for
hardware, page 48-48. (Keep hardware loose.)
ping plug must be removed before shredder opera-
tion. Replace plug with dipstick in filler tube after
shredder has been removed from truck and leveled.
38 Assembly
MAN0506 (Rev. 9/5/2008)
7. Attach front top link spacer, bolts, and lock nuts to
3. Install front parking stands (Figure 44), using L-pin
front of upper mast assembly.
and hair pin cotter.
NOTE:
For Quick Hitch Cat II, use spacer in front lower
hole of upper mast assembly.
For Quick Hitch Cat III, use spacer in front upper
hole of upper mast assembly.
Without Quick Hitch, use spacer through top link
pivot in front upper hole of upper mast assembly.
8. Assemble lower 3-point hitch pin assembly,
spacers, and klik pin to lower mast (both sides).
NOTE: For Quick Hitch Cat II & III, place 1-3/4
OD spacer on the inside and 1-7/16 OD spacer on
the outside.
Figure 44. Front Stands Installed
PULL-TYPE HITCH INSTALLATION
(Pull-type units only)
1
1. Mount hitch to 3-point lower mounts, using pins
and Klik pins.
2. Install ratchet. Be sure to install retaining pins.
3. Attach clevis or pin to hitch tongue (See page 48
for parts breakdown.)
4. Attach tow chain to hitch.
7082Z
Figure 42. Floating Upper Mast Installed
ALL UNITS
1. Install PTO driveline by sliding the yoke with the
slip clutch over the input shaft (Figure 43).
2. Tighten interlocking clamp bolts to their specified
torque.
Figure 45. Pull-Type Hitch Installed
Figure 43. Gearbox Input Shaft
MAN0506 (Rev. 9/5/2008)
Assembly 39
NOTE: Use equal number of belting and bars on
each side of shredder.
MANUAL STORAGE TUBE INSTALLATION
The manual storage tube may be supplied in either of
the following styles.
3. Tighten all hardware.
RUBBER FLAP INSTALLATION
For One-Piece Style Manual Tube:
1. Remove all components from shipping carton.
Mount the manual tube to the inside of the shredder
side sheet, using three 3/8 x 1-1/4" hex bolts, washers,
and 3/8" nuts. Mounting holes are located above the
bearing plate (see Figure 46).
Make sure that all required hardware is included.
2. Attach flap brackets to the front of the shredder
using 3/8 NC x 1-1/2 carriage bolts and 3/8 flange
lock nuts.
NOTE: Use flap brackets to space flap brackets
out evenly across front of shredder.
3. Attach flap bars to flat brackets using 3/8 NC x 1-
1/2 carriage bolts and 3/8 flange lock nuts.
4. Assemble rod and rubber flaps through flap
brackets and secure using 3/16 x 1-1/2 cotter pins.
5. Tighten all hardware.
6. For detailed installation instructions, see the parts
diagram and instruction sheet the comes with the
swing flap kit designed for each shredder.
Figure 46. One-Piece Style Manual Tube Installed
For Clamp-Style Manual Tube:
1. Mount the tube clamp to the inside of the shredder
side sheet using two 1/4" self-tapping screws
(Figure 47). Mounting holes are located above the
bearing plate.
2. Place the tube in the clamp with the cap facing
forward.
NOTE: Keep the Operator’s Manual with the
shredder at all times.
1. Rubber flap
2. Flap bracket, right
3. Flap bracket, left
5. flap rod
6. Swing flap bar, mast plate
7. Swing flap bar
8. 3/8 NC x 1 Carriage bolt
9. 3/8 NC Flange lock nut
10. 3/16 x 1-1/2 Cotter pin
Figure 47. Clamp-Style Manual Tube Assembly
OPTIONAL EQUIPMENT
Figure 48. Rubber Flat Installation (15’ Shown)
RUBBER BELTING INSTALLATION
SAFETY LIGHT KIT INSTALLATION
1. Remove all components from shipping carton.
Make sure that all required hardware is included.
1. Remove all components from shipping carton.
Make sure that all required hardware is included.
2. Attach rubber belting and bars to front of shredder
using 3/8 NC x 1-1/2 carriage bolts and 3/8 flange
lock nuts.
2. Attach dual safety lights (Figure 49) to their bases
using 1/4 NC x 1" hex bolts, washers and nuts
40 Assembly
MAN0506 (Rev. 9/5/2008)
provided. Make sure that light lenses are in the
correct position in relation to direction of equipment
travel: amber lenses on the outside, red lenses on
the inside facing rear of shredder.
3. Install light bracket on end of shredder using 1/2
NC x 1-1/2" hex bolts, washers and nuts (four
each) in slots 3 and 4 on top of end sheet.
4. Plug ends of wiring harness into corresponding
plugs of the light units (Note: left side of wishbone
harness is labeled “Left”).
5. Run wiring harness along top of shredder and
secure with enclosed adhesive-backed clamps (5)
approximately every two feet.
Figure 51. Safety Light Installed - Front View
6. Connect 7-pin connector of wiring harness to
tractor and test all light functions before actual use.
Install Center Deflector
Slide deflector (1) between shredder center channel
with the point forward.
Secure into position using four 1/2 NC x 1-1/4 carriage
bolts (2) and flange lock nuts (3).
3
2
5. Dual lamp, 4-pin LH
6. Dual lamp, 4-pin RH
8. Clamp, adhesive-backed
9. 1/4 NC x 1" Hex bolt
10. 1/4 NC Hex nut
11. 1/4" Lock washer
12. 1/4" Flat washer
DP3
1
20. Wiring harness
21. Dual light bracket
1. Center deflector
Figure 49. Safety Light Kit Diagram (Non-End Tow)
2. 1/2 NC x 1-1/4 carriage bolt
3. 1/2 NC Flange lock nut
Figure 52. Center Deflector Installed
Figure 50. Safety Light Installed - Rear View
MAN0506 (Rev. 9/5/2008)
Assembly 41
2. Install adapter (23) and hose (11) to the OUT or
CENTER CUT KIT INSTALLATION
Block Shredded
RETURN side of the motor.
3. Place motor (4) inside motor housing (2) and
secure using six 9/16 NC x 1-1/2 cap screws (7)
lock nuts (6).
Make sure OUT or RETRUN side of motor is on the
open side of the motor housing. Torque hardware
to 171 lbs-ft.
„ Never go underneath equipment (lowered to the
ground or raised) unless it is properly blocked and
secured. Never place any part of the body under-
neath equipment or between moveable parts even
when the engine has been turned off. Hydraulic
system leak down, hydraulic system failures,
mechanical failures, or movement of control levers
can cause equipment to drop or rotate unexpect-
edly and cause severe injury or death. Follow Oper-
ator's Manual instructions for working underneath
and blocking requirements or have work done by a
qualified dealer.
4. Slide blade hub (1) over motor shaft, install 1/4"
key and secure using one 5/16 NF x 1-1/2 cap
screw (20), flat washers (33) and lock washer (34)
in the bottom of the shaft. Torque to 19 lbs-ft.
5. Clamp hub to shaft using two 3/8 NC x 1-3/4 cap
screws (18) and lock nuts (22). Torque to 35 lbs-ft.
6. Secure blade (3) to blade hub using two 3/8 NC x
1-1/4 cap screws (19) and flange lock nuts (22).
Torque to 35 lbs-ft.
To minimize the potential hazards of working under-
neath the cutter, follow these procedures.
1. Jackstands with a load rating of 2000 lbs or more
are the only approved blocking device for this
cutter. Install a minimum of four jackstands under
the shredder before working underneath unit.
Do not position jackstands under wheels, axles, or
wheel supports. Components can rotate and cause
shredder to fall.
2. Consider the overall stability of the blocked unit.
Just placing jackstands underneath will not ensure
your safety.
The working surface must be level and solid to
support the weight on the jackstands. Make sure
jackstands are stable, both top and bottom. Make
sure shredder is approximately level.
3. With full shredder weight lowered onto jackstands,
test blocking stability before working underneath.
4. If shredder is attached to tractor when blocking, set
the brakes, remove key, and block shredder before
working underneath.
5. Securely block rear tractor wheels, in front and
behind. Tighten tractor lower 3-point arm anti-sway
mechanism to prevent side-to-side movement.
Assemble Motor and Blade
1. Install elbow (8), adapter (9), elbow (10) and hose
(11) to the IN or PRESSURE side of the hydraulic
motor.
Figure 53. Motor Assembly
42 Assembly
MAN0506 (Rev. 9/5/2008)
4. Place hose assembly around center plate of
shredder and drape quick couplers over the front of
the shredder. See Figure 55 and Figure 56.
Install Motor Housing
1. Slide motor assembly between shredder center
channel and secure to the left side using two 1/2
NC x 1-1/4 carriage bolts (29) and flange lock nuts
(30).
5. Make sure hose with check valve is on the right
side of the center plate.
2. Install 1/2 NC x 1 cap screw (31) and flat washer
(32) to the right rear hole of the motor housing and
secure with flange lock nuts (30).
3. Install 1/2 NC x 1-1/4 carriage bolt (29) and flange
lock nut (30) into the right front hole.
4. Raise motor housing to the bottom of the mounting
slots and torque hardware to 85 lbs-ft.
31
Figure 55. Hose Assembly
6. Route hose (11) from the IN side of the motor
between shredder and rockshaft and attach it to
tee (12) on the left side of the center plate.
30
29
7. Route hose (11) from the OUT side of the motor
between shredder and rockshaft and attach it to
tee (12) on the right side of the center plate.
DP1
RETURN
Figure 54. Motor Assembly Installed
Center Plate
PRESSURE
Assembly Hoses
1. Attach male quick coupler (17) and adapter (16) to
the end of hose (15). Attach tee (12) to the
opposite end of hose.
Check
Valve
2. Attach male quick coupler (17) and adapter (16) to
the end of second hose (15). Attach check valve
(14), nipple (13) and tee (12) to the opposite end of
hose.
11
NOTE: Make sure flow indicator arrow on the side
of the check valve (14) is pointing in the correct
direction. See Figure 55
3. Install check valve (14) and two nipples (13)
11
between the two tees (12).
IN
OUT
DP2
NOTE: Make sure flow indicator arrow on the side
of the check valve (14) is pointing in the correct
direction.
Figure 56. Hose Routing
MAN0506 (Rev. 9/5/2008)
Assembly 43
Install Hose Clamps
Connect Hoses to Tractor
1. Place hose clamps (36) around hoses (11) and
NOTICE
center hoses between center plate.
■
Oil flow to hydraulic motor must not exceed 28
2. Mark clamp holes in desired location on shedder
gpm.
body and drill two 11/32" holes.
1. Connect PRESSURE hose to a tractor rear remote
quick coupler that has a lever (handle) that can be
placed in the detent or locked position.
3. Secure hose clamps to shredder using 5/16 NF x
1-1/4 cap screws (20), flat washers (33), lock
washers (34) and hex nuts (35). See Figure 57.
2. RETURN hose must be connected directly to the
tractor reservoir or to a specifically designated
motor return or ‘zero’ back pressure port.
Install Decals
Apply safety decals (24 & 25) to a clean surface on the
back of the shredder where they can be seen with out
obstructions. Install decals (25) on either side of the
hose assembly. See Figure 57.
Remove Deflector Kit
1022652 deflector kit must be removed from the shred-
der before using cutter kit. Deflector kit pushes material
away from the cutter kit and preventing material from
being cut.
Figure 57. Hose Clamp Installation
™
44 Assembly
MAN0506 (Rev. 9/5/2008)
DEALER CHECK LISTS
___ Point out the safety decals. Explain their meaning
PRE-DELIVERY CHECK LIST
and the need to keep them in place and in good
condition. Emphasize the increased safety haz-
ards when instructions are not followed.
(DEALER’S RESPONSIBILITY)
Inspect the equipment thoroughly after assembly to
make sure that it is set up properly before delivering it
to the customer.
___ Present Operator's Manual and request that cus-
tomer and all operators read it before operating
equipment. Point out the manual safety rules,
explain their meanings and emphasize the
increased safety hazards that exist when safety
rules are not followed.
The following check lists are a reminder of points to
inspect. Check off each item as it is found satisfactory
or after proper adjustment is made.
___ Check that all safety decals are installed and in
good condition. Replace if damaged.
___ Explain to customer the potential crushing haz-
ards of going underneath raised equipment.
Instruct customer that service work does not
require going underneath unit and never to do so.
___ Properly attach implement to tractor and make all
necessary adjustments.
___ Check all bolts to be sure they are properly
torqued.
___ Show customer the safe, proper procedures to be
used when mounting, dismounting, and storing
equipment.
___ Check wheel bolts for proper torque.
___ For mounted units, add wheel weights, ballast in
front tires, and/or front tractor weight to enhance
front end stability. A minimum 20% of tractor and
equipment gross weight must be on front tractor
wheels. When adding weight to attain 20% of
tractor and equipment weight on front tractor
wheels, you must not exceed the ROPS weight
certification. Weigh the tractor and equipment. Do
not estimate!
___ Check that all cotter pins and safety pins are
properly installed. Replace if damaged.
___ Check and grease all lubrication points as identi-
fied in Lubrication Schedule, page 24.
DELIVERY CHECK LIST
(DEALER’S RESPONSIBILITY)
___ Show customer how to make adjustments.
___ Make customer aware of optional equipment
available so that customer can make proper
choices as required.
___ Instruct customer how to lubricate and explain
the importance of lubrication.
™
MAN0506 (Rev. 9/5/2008)
Dealer Check Lists 45
NOTES
46 Dealer Check Lists
MAN0506 (Rev. 9/5/2008)
PARTS INDEX
FLAIL SHREDDER
Center Drive
FRAME ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48-48
FLAIL TUBE ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50
WHEEL ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51
BED CONE ASSEMBLY (OPTIONAL) . . . . . . . . . . . . . . . . . . . . . . . . .52
WEASLER® PTO SHAFT WITH TORQMASTER CLUTCH
24K PULL-TYPE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52 - 53
24K 2-POINT & 3-POINT . . . . . . . . . . . . . . . . . . . . . . . . . .54
DUAL SAFETY LIGHT KIT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .54
WEASLER 24K TORQMASTER CLUTCH . . . . . . . . . . . . . . . . . . . . . .55
WEASLER 30K AUTOMATIC CLUTCH (OPTIONAL). . . . . . . . . . . . . .55
WEASLER PTO SHAFT WITH AUTOMATIC CLUTCH (OPTIONAL)
30K 3-POINT. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .56
30K PULL-TYPE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .57
CENTER DRIVE GEARBOX ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . .58
RUBBER BELTING (OPTIONAL) . . . . . . . . . . . . . . . . . . . . . . . . . . . . .59
CENTER CUTTER KIT (OPTIONAL) . . . . . . . . . . . . . . . . . . . . . . 60 - 61
CENTER DEFLECTOR (OPTIONAL) . . . . . . . . . . . . . . . . . . . . . . . . . .61
RUBBER FLAPS (OPTIONAL) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .62
(Rev. 10/13/2010)
MAN0506 (Rev. 9/7/2011)
Parts 47
CENTER DRIVE FLAIL SHREDDER FRAME ASSEMBLY
48 Parts
MAN0506 (Rev. 9/5/2008)
CENTER DRIVE FLAIL SHREDDER FRAME ASSEMBLY PARTS LIST
REF PART
QTY
DESCRIPTION
REF PART
QTY
DESCRIPTION
1
1
1
1
1
2
NSS
1
1
1
1
1
-
S15CD Body weldment
S20CD Body weldment
S22CD Body weldment
S25CD Body weldment
S27CD Body weldment
36
37
20973 * AR 3/8 NC x 1-1/4 Carriage bolt GR5
565 * AR 3/8 Flat washer
NSS
NSS
38 90006500 * AR 3/8 NC Top lock nut
NSS
39 50530831
41 90002734 *
42 90006019
1
4
2
2
Hitch, Cat 3 complete (items 51-54)
5/8 NC x 1-3/4 Hex bolt, black
1" NC Nut
NSS
----------
Flail tube asy, right & left
(see page 50)
43
44
45
45
45
1013067
1012202
1016188
1016195
1019763
Skid weldment
3
3
3
3
3
5
6
7
8
9
1016168
1013097
1016167
1013057
1013122
90507112
1012170
1010120
56383
1
1
1
1
1
1
2
2
2
2
2
1
1
15’ Rockshaft asy
AR Rubber belt shield
20’ Rockshaft asy
AR Rubber belt shield, 15’ & 27’
AR Rubber belt shield, 20’
AR Rubber belt shield, 22’
22’ Rockshaft asy
25’ Rockshaft asy
27’ Rockshaft asy
47 10033957
1
Manual storage tube, clamp style
-or-
Tow chain (pull-type only)
Bearing, 2-3/16 flange
Bearing plate
47 1003828
1
2
1
1
1
1
1
2
2
2
1
1
2
2
4
4
4
2
5
5
2
2
2
2
2
2
1
Manual storage tube, 1-piece style
1" Lock washer
48 90011021
49 50530219
50 50520412
51 50530834
52 50530832
53 50530833
54 90001411
55 90001537
58 90023081 *
59 50520433
60 20030151
63 50030338
64 90109126
65 90039030
66 50530313
Pin weldment
Pin, rear hitch
50520211
Parking stand, square
Parking stand pin
Pull-type hitch weldment
Top plate
10 50530279
14 1013049
16 1016104
Gearbox 800 Series (see page 58)
Cushion
3-Point PTO shaft, 1-3/8" yoke with
clutch (see page 52)
V-Plate
3/4 NC x 3 Hex bolt GR5
1 NC x 6-1/2 Hex bolt GR5
3/8 x 2 Cotter pin
16 1016105
16 1016106
16 1016107
16 1016108
16 1016109
1
1
1
1
1
3-Point PTO shaft, 1-3/4" yoke with
clutch (see page 52)
3-Point PTO shaft, 1-3/8" yoke with
clutch long (see page 52)
Clevis hitch kit
1" ID Mast spacer bushing
Drive hub, splined inner
O-Ring, flail coupler
Snap ring, 1-3/4
3-Point PTO shaft, 1-3/4" yoke with
clutch long (see page 52)
Pull-type PTO shaft, 1-3/8" yoke
with clutch (see page 52)
Pull-type PTO shaft, 1-3/4" yoke
with clutch (see page 52)
Stud bolt, 5/8 NC x 2-3/4 GR5
Spacer mast .75 x 3.00
Hardened bushing
Bolt, 1 x 5 HHCS GR5
Nut, 1 NC Top lock
Spacer, 1-3/4 OD
67
68
1016187
1016186
17 1012175
20 90025004 *
21 90025012 *
22 20020705
24 20020553
24a 90029204 *
25 90006143
27 1019786
29 1019755
1
2
2
1
2
1
Gearbox stand
1/8 Hair pin cotter
69 90001531
70 90006514
71 20030960
72 20030961
73 20030959
7/16 x 2 Klik pin
Ratchet jack with pipe
Lower 3-pt hitch pin assembly
5/16 x 1-5/8 Roll pin
Spacer, 1-7/16 OD
Spacer. 1-3/4 OD
24 1/2 NC Nut, Spiralock flanged
75
1013114
Upper mast plate
1
-
Dipstick tube/Jam nut/Dipstick
Complete safety decal set
76 20020553
77 90017110
78 10033958
Lower 3-pt hitch pin asy
1/4 x 1/2 Hex wash self-tap screw
Clamp
30
31 90023084 *
32 230 *
12735 * 24 1/2 NC x 1-3/4 HT Carriage bolt
2
8
8
8
3/8 x 3-1/2 Cotter pin
5/8 NC Nut ZP
AR
NSS
*
As Required
33 90001786 *
34 90011015 *
5/8 NC x 2 Carriage bolt
5/8 Lock washer
Not Sold Separately
Standard hardware; obtain locally
MAN0506 (Rev. 9/7/2011)
Parts 49
FLAIL TUBE ASSEMBLY
LEFT
RIGHT
REF PART
QTY
DESCRIPTION
Stub shaft, 2-3/16"
REF
QTY
DESCRIPTION
PART #
PART #
2
3
3
1012163
50531067
1019788
2
1
1
1016199LK 1016198LK
1016199HD 1016198HD
1
1
15’ Flail tube w/knives
AR L-Knife, long 8-1/2", (6 mm)
15’ HD Cotton tube
w/knives
AR L-Knife, HD cotton
(Durafaced) (8 mm)
1
1016199CP 1016198CP
1
15’ Cup knife tube
w/knives
4
5
6
6
7
8
9
50531048
50030779
1010056
1019789
50030345
1013092
90002526
AR Weld-on clip
12 3/8 High collar lock washer
AR L- Knife, cut off
1
1
1013109LK 1013108LK
1013109HD 1013108HD
1
1
20’ Flail tube w/knives
20’ HD Cotton tube
w/knives
AR L- Knife, cut off
2
Drive hub sleeve, outer
1
1013109CP 1013108CP
1
20’ Cup knife tube
w/knives
12 3/8 NC x 2-1/2 SHCS
6
2
2
1/2 NC x 2-3/4 Tap bolt, full thread
1/8 NPT Straight grease fitting
2-7/16 Hub, E-style
1
1
1016179LK 1016178LK
1016179HD 1016178HD
1
1
22’ Flail tube w/knives
10 90515001 *
11 1012164
22’ HD Cotton tube
w/knives
1
1016179CP 1016178CP
1
22’ Cup knife tube
w/knives
12 90001357 * AR 5/8 NC x 3-1/2 Hex bolt GR5
13 50530405
14 50530974
14 50530973
14 50530972
AR Hardened wear bushing
AR Steel cup flail 11" (Standard)
AR Steel cup flail 9"
1
1
1012169LK 1012168LK
1012169HD 1012168HD
1
1
25’ Flail tube w/knives
25’ HD Cotton tube
w/knives
AR Steel cup flail short
1
1012169CP 1012168CP
1
25’ Cup knife tube
w/knives
15 90011013 * AR 1/2 Lock washer
16 11900 * AR 1/2 NC Flange lock nut
17 90006508 AR 5/8 NC Top lock nut
18 90011015 * AR 5/8 Lock washer
1
1
1013119LK 1013118LK
1013119HD 1013118HD
1
1
27’ Flail tube w/knives
27’ HD Cotton tube
w/knives
19 1010061
19 1012184
20 1010062
AR Spacer, steel (for 6 mm L-knife)
1
1013119CP 1013118CP
1
27’ Cup knife tube
w/knives
AR Spacer, steel (for 8 mm L-knife)
AR Bushing, L-knife
21 90001758 * AR 1/2 NC x 3-1/4 Carriage bolt
SHCS
NS
AR
*
Socket Head Cap Screw
Not Shown
As Required
Standard hardware, obtain locally
50 Parts
MAN0506 (Rev. 9/5/2008)
WHEEL ASSEMBLY
REF PART NO
QTY
1
DESCRIPTION
REF PART NO
QTY
1
DESCRIPTION
1
2
90509009
90109002
90101023
90101022
90509011
90509003
90101016
90101015
90509067
90023043 *
90006060
90509070
90509078
90509117
2377
Dust cap
Seal
16
16
17
18
18
19
20
21
22
23
50520111
50520112
1010013
Strut weldment
1
1
Strut assembly with hubs
Caster arm assembly (8 holes)
Caster weldment
3
1
Inner bearing cone
Inner cup
1
4
1
50520197
50520198
1010014
1
5
5
1/2 NF Wheel nut
Hub, 5-bolt
1
Caster and hub assembly
Back plate (8 holes)
Oilite washer
6
1
1
7
1
Outer bearing cup
Outer bearing cone
7/8 Washer
20031233
20031219
20031766
90515024 *
1
8
1
1
Plate, retainer
9
1
2
Caster pivot bearing
10
11
12
13
14
15
1
3/16 x 1-1/2 Cotter pin
7/8 NF Slotted nut
Tire, 9.5L x 15
1
1/4 - 28 UNF Straight grease fit-
ting
1
24
26
27
90001221 *
90006015
90011017
1
8
8
1/2 NC x 1 Hex bolt GR5
3/4 NC Hex nut
1
1
Wheel rim (15" x 6 - 5 bolt)
1/2 NF x 1-7/8 Stud bolt
3/4 Lock washer
5
6
3/4 NC x 6 Hex bolt GR5
*
Standard hardware, obtain
locally
(Qty: 8 for 1010013 & 1010014)
MAN0506 (Rev. 9/7/2011)
Parts 51
BED CONE ASSEMBLY (OPTIONAL) 50510065
REF PART NO
QTY
1
DESCRIPTION
U-Bolt, 3/4 NC x 4 x 5.5 long
3/4 NC x 6 Hex bolt GR5
Strut weldment
1
2
3
4
5
6
7
8
9
A
20031440
2377
6
50520162
50520163
50530349
50520164
90001696 *
90101002
NSS
1
1
Yoke weldment
1
Scraper
1
Roller weldment
7
3/8 NC x 1-1/4 Carriage bolt GR5
1-1/4 Insert bearing
2-Hole flange
2
4
50520179
1
Packer asy (Items 4-9)
NSS Not sold separately
Standard hardware, obtain locally
*
TYPE A - WEASLER® 24K PULL-TYPE PTO SHAFT WITH TORQMASTER CLUTCH
REF
PART NO
QTY
1
DESCRIPTION
Slide lock repair kit 1.38 ID -or-
Slide lock repair kit 1.75 ID
Slide lock yoke asy 1.38 ID -or-
Slide lock yoke asy 1.75 ID
Cat 6 CV U-joint repair kit
CV Bell shield
REF PART NO
QTY
1
DESCRIPTION
1
19851
10
11
12
13
14
15
A
1010819
Outer guard & bearing
19837
90317733
90318121
58759
1
1010820
33347
1
Inner guard & bearing
2
1
1
Decal, Danger, Guard missing
Yoke, tube & slip sleeve
1
90317909
58765
1
3
4
5
6
7
8
9
2
1
U-Joint cross & bearing kit
Clutch asy, 55 clamp 24K
PTO CV 1.38-21 CD P-type 24KE
PTO CV 1.75-20 CD P-type 24KE
Tractor half asy with guard 1.38
Tractor half asy with guard 1.75
19840
1
1010805
1016108
1016109
1016127
1016125
1
58760
1
CV Body with fitting
1
90318183
19846
1
Yoke & shaft 26.8
A
1
2
Shield bearing repair kit
Safety sign
B
1
18864
1
B
1
55648
1
Centralizer repair kit (not shown)
(Rev. 8/23/2011)
52 Parts
MAN0506 (Rev. 9/5/2008)
TYPE B - WEASLER® 24K PULL-TYPE PTO SHAFT WITH TORQMASTER CLUTCH
REF
A
PART NO
QTY
1
DESCRIPTION
PTO complete 1-3/8 21 spline -or-
PTO complete 1-3/4 20 spline
Slide lock repair kit 1.38 ID -or-
Slide lock repair kit 1.75 ID
Slide lock yoke asy 1.38 ID -or-
Slide lock yoke asy 1.75 ID
Cat 6 CV U-joint repair kit
CV Bell shield
REF PART NO
QTY
1
DESCRIPTION
1016108
10
11
12
13
14
15
A
1010819
Outer guard & bearing
A
1016109
19851
1
1010820
33347
1
Inner guard & bearing
1
1
1
Decal, Danger, Guard missing
Yoke, tube & slip sleeve
19837
1
90317909
58765
1
2
1033104
1033105
1033107
19840
1
1
U-Joint cross & bearing kit
Clutch asy, 55 clamp 24K
PTO CV 1.38-21 CD P-type 24KE
PTO CV 1.75-20 CD P-type 24KE
Tractor half asy with guard 1.38
Tractor half asy with guard 1.75
1
1010805
1016108
1016109
1016127
1016125
1
3
4
5
6
7
8
9
2
1
1
A
1
1033106
1033109
19846
1
CV Body with fitting
B
1
1
Yoke & shaft
B
1
2
Shield bearing repair kit
Safety sign
18864
1
55648
1
Centralizer repair kit (not shown)
(Rev. 10/13/2010)
MAN0506 (Rev. 9/7/2011)
Parts 53
®
WEASLER 24K 2-POINT & 3-POINT PTO SHAFT WITH TORQMASTER CLUTCH
10
3
3
4
11
5
9
2
1
6
8
5
7
CD6523
REF PART QTY
DESCRIPTION
REF PART QTY
DESCRIPTION
1
1
2
2
3
4
4
5
6
7
19851
19837
1
1
1
1
2
1
1
1
1
1
Slide lock repair kit 1.38 ID -or-
Slide lock repair kit 1.75 ID
10 90317724
11 1010805
1
1
Yoke, tube & slip sleeve
Friction overrunning clutch asy. 55
clamp (24K)
90317208
90317418
1016113
90318183
90318074
19846
Slide yoke assembly 1.38 ID -or-
Slide yoke assembly 1.75 ID
U-Joint cross & bearing kit
Yoke & shaft 26.8 center-end -or-
Yoke & shaft, 32.9 center-end
Shield bearing repair kit
A
A
B
1016104
1016105
1016106
1
1
1
PTO Shaft complete 1-3/8 -21 CD Std
PTO Shaft complete 1-3/4 -20 CD Std
PTO Shaft complete 1-3/8 -21 CD
long
B
1016107
1
PTO Shaft complete 1-3/4 -20 CD
long
18864
Safety sign
C
C
D
D
E
1016117
1016111
1016122
1016124
1016112
1
1
1
1
1
Tractor half asy w/guard 1-3/4 Std
Tractor half asy w/guard 1-3/8 Std
Tractor half asy w/guard 1-3/8 long
Tractor half asy w/guard 1-3/4 long
Implement half asy w/guard 24K
1010803
Outer guard & bearing (1016117,
1016111) -or-
7
1010813
1
Outer guard & bearing (1016122,
1016124)
8
9
1010804
33347
1
1
Inner guard & bearing
Safety sign, Danger, Guard missing
DUAL SAFETY LIGHT KIT (OPTIONAL)
REF PART NO
QTY
1
DESCRIPTION
5
6
90401149
90401150
90507121
Dual lamp, 4-pin LH
Dual lamp, 4-pin RH
1
8
12 Clamp, adhesive-backed
9
90001009 * 10 1/4 NC x 1 Hex bolt GR5
90006001 * 10 1/4 NC Hex nut
90011009 * 10 1/4 Lock washer
90011031 * 10 1/4 Flat washer
10
11
12
20
90401152
1
Wiring harness, wishbone
26’
21
50530986
2
Bracket, dual safety light
*
Standard hardware, obtain
locally
(Rev. 8/23/2011)
54 Parts
MAN0506 (Rev. 9/5/2008)
WEASLER® 24K TORQMASTER CLUTCH ASSEMBLY
REF
9
PART NO
QTY
1
DESCRIPTION
90318170
Leaf spring
10
11
12
13
90318171
90318175
90318174
90003055
1
Overrunning key
Friction disk
2
REF
PART NO
QTY
DESCRIPTION
1
Separator plate
1
1010831
1
Yoke, Clamp style with overrun-
ning clutch & hub asy (10 mm
bolts) (includes Items 2-10)
4
M10 x 1.50 x 25 Serrated hex
head cap screw
14
15
16
17
A
90003053
6
M8 x 1.25 x 60 Hex bolt, CL 10.9
1A
1019629
1
Overrunning clutch repair kit
(includes items 2, 6, 7, 9, & 10)
90011236 A/R Washer, 8 mm x 1.6 thick
90006548
1010833
1010832
6
1
1
Nut, M8 x 1.25 Hex ZP
Hub clamp asy 1.75
2
3
4
5
6
7
8
90318165
90318154
1
1
Wave spring
Set screw, .312-18 x .25 long
Friction pack, overrunning (10
mm bolts, 24K)
90317541 31 Ball, 1/4" dia.
1019630
90318167
90318168
90318169
1
1
1
1
OR Inner hub assembly
Washer
B
1010805
1
Complete clutch asy, 55 clamp
(10 mm bolts, 24K)
Retaining ring
NSS = Not Serviced Separately
Overrunning hub
WEASLER® AUTOMATIC CLUTCH (OPTIONAL)
REF
A
PART NO
QTY
DESCRIPTION
Automatic clutch asy complete
Yoke & hub, 30K auto
1019811
-
1
1019813
1019814
1010833
1025874
1
1
1
6
2
Clutch pack, 30K auto
3
Hub clamp assembly 1-3/4
4
HHCS, M12-1.75P x 20 mm
CL10.9 flanged head
MAN0506 (Rev. 9/7/2011)
Parts 55
WEASLER® 30K 3-POINT PTO SHAFT WITH AUTOMATIC CLUTCH (OPTIONAL)
REF PART QTY
DESCRIPTION
REF PART QTY
DESCRIPTION
A
1019810
-
PTO Shaft complete 1-3/4 20-spline
30K 3-point with automatic clutch
6
7
8
9
90317455
1022638
1022639
33347
1
1
1
1
1
1
Safety sign
Outer guard & bearing
Inner guard & bearing
1
2
3
4
5
19837
90317418
58765
1
1
2
1
2
Slide lock repair kit 1.75 ID
1-3/4 20-Spline yoke
Danger decal, guard missing
Yoke, tube & slip sleeve
U-Joint cross & bearing kit 55E
Yoke & shaft, (1.69 - 20 spline)
Drive shield bearing kit
10 1022640
11 1019811
1022637
1009065
Automatic clutch assembly 30K (see
page 55 for breakdown)
WEASLER® 30K 3-POINT PTO SHAFT WITH AUTOMATIC CLUTCH (OPTIONAL)
REF PART QTY
DESCRIPTION
REF PART QTY
DESCRIPTION
A
1026555
-
PTO Shaft complete 1-3/4 20-spline
30K 3-point with automatic clutch
6
7
8
9
90317455
1010803
1010804
33347
1
1
1
1
1
1
Safety sign
Outer guard & bearing
Inner guard & bearing
1
2
3
4
19837
90317418
58765
1
1
2
1
Slide lock repair kit 1.75 ID
1-3/4 20-Spline yoke
Danger decal, guard missing
Yoke, tube & slip sleeve
U-Joint cross & bearing kit 55E
Yoke & shaft, 1.69 20-spline, 30.6 long
-OR-
10 90317724
11 1019811
90317613
-OR-
Automatic clutch assembly 30K (see
page 55 for breakdown)
4
5
90318183
1009065
1
2
Yoke & shaft, 1.69 20-spline, 26.8 long
Drive shield bearing kit
(Rev. 11/8/2011)
56 Parts
MAN0506 (Rev. 9/5/2008)
TYPE A - WEASLER® 30K PULL-TYPE PTO SHAFT WITH AUTOMATIC CLUTCH (OPTIONAL)
REF PART QTY
DESCRIPTION
REF PART QTY
DESCRIPTION
A
1019820
-
PTO Shaft complete 1-3/4 20-spline
30K pull-type with automatic clutch
7
8
18864
1022642
1022643
33347
1
1
1
1
1
2
1
Safety sign
Outer guard & bearing
1
2
3
4
5
6
19837
90318121
58759
1
1
2
1
1
2
Slide lock repair kit 1.75 ID
Slide lock yoke assembly
CV U-Joint repair kit 55E
CV Body with fitting
9
Inner guard & bearing
10
Danger decal, guard missing
Yoke, tube & slip sleeve
U-Joint cross & bearing kit 55E
11 1022644
12 58765
13 1019811
58760
1022641
1009065
Yoke & shaft (1.69 - 20 spline)
Drive shield bearing kit
Automatic clutch assembly 30K (see
page 55 for breakdown)
TYPE B - WEASLER® 30K PULL-TYPE PTO SHAFT WITH AUTOMATIC CLUTCH (OPTIONAL)
REF PART QTY
DESCRIPTION
REF PART QTY
DESCRIPTION
A
1019820
-
PTO Shaft complete 1-3/4 20-spline
30K pull-type with automatic clutch
7
8
18864
1022642
1022643
33347
1
1
1
1
1
2
1
Safety sign
Outer guard & bearing
1
2
3
4
5
6
19837
1033105
1033107
1033106
1033109
1009065
1
1
2
1
1
2
Slide lock repair kit 1.75 ID
Slide lock yoke assembly
CV U-Joint repair kit 55E
CV Body with fitting
9
Inner guard & bearing
10
Danger decal, guard missing
Yoke, tube & slip sleeve
U-Joint cross & bearing kit 55E
11 1022644
12 58765
13 1019811
Yoke & shaft (1.69 - 20 spline)
Drive shield bearing kit
Automatic clutch assembly 30K (see
page 55 for breakdown)
(Rev 10/13/2010)
MAN0506 (Rev. 9/7/2011)
Parts 57
CENTER DRIVE GEARBOX
REF PART QTY
DESCRIPTION
A
1
2
3
1013049
1019782
1019783
1019784
1
1
1
1
Complete gearbox, Series 800
Casting, Threaded holes
Casting, Non-threaded holes
Pinion shaft/gear asy 27T with bearing
cones & bearing cups
4
5
6
7
8
9
90315546
90101150
90101152
1019785
1019787
90039030
1
1
2
4
3
1
3
2
8
1
1
-
Cross shaft/gear asy 20T
Bearing cone
Bearing cup
Bolt, 3/8-16 x 2.75 SHCS
Guard, seal
Snap ring 1.750
10 90109125
11 90503078
12 90003033
13 90501159
14 90101328
Seal TC-1.750-2.437-.312
Plug, 1/2-14 NPT SCHD W/3M
Bolt, 3/8-16 x 2.25 SHCS
Bushing, 1/2 NPT to 1/8 NPT
Bearing cone
15
16
NSS
NSS
NSS
Bearing cone (included in item 3)
Bearing cone (included in item 3)
Not Serviced Separately
-
58 Parts
MAN0506 (Rev. 9/5/2008)
RUBBER BELTING
REF PART
QTY
DESCRIPTION
Rubber belting (15 ft)
REF PART
QTY
DESCRIPTION
1
1
1
2
2
2
3
3
3
4
4
4
1012202
1012202
1012202
1022647
1022647
1022647
1022649
1022648
1022650
1016188
1016195
1019763
4
6
8
4
6
8
2
2
2
2
2
2
5
5
5
5
5
6
6
6
6
6
64824 * 34 3/8 NC x 1-1/2 Carriage bolt (15 ft)
64824 * 46 3/8 NC x 1-1/2 Carriage bolt (20 ft)
64824 * 50 3/8 NC x 1-1/2 Carriage bolt (22 ft)
64824 * 62 3/8 NC x 1-1/2 Carriage bolt (25 ft)
64824 * 34 3/8 NC x 1-1/2 Carriage bolt (27 ft)
14350 * 34 3/8 NC flange lock nut (15 ft)
14350 * 46 3/8 NC flange lock nut (20 ft)
14350 * 50 3/8 NC flange lock nut (22 ft)
14350 * 26 3/8 NC flange lock nut (25 ft)
14350 * 62 3/8 NC flange lock nut (27 ft)
Rubber belting (20 ft & 22 ft)
Rubber belting (25 ft & 27 ft)
Belt bar (15ft)
Belt bar (20 ft & 22 ft)
Belt bar (25 ft & 27 ft)
Belt bar (15 ft & 27 ft)
Belt bar (20 ft)
Belt bar (22 ft)
Rubber belting (15 ft & 27 ft)
Rubber belting (20 ft)
Rubber belting (22 ft)
*
Standard hardware, obtain locally
MAN0506 (Rev. 9/7/2011)
Parts 59
CENTER CUTTER KIT (OPTIONAL)
24 - 50530315
25 - 50530263
WARNING
ADVERTENCIA
HIGH-PRESSURE FLUID HAZARD
To prevent serious injury or death:
1. Relieve pressure on system before
repairing, adjusting, or disconnecting.
2. Wear proper hand and eye protection
when searching for leaks. Use wood or
cardboard instead of hands.
3. Keep all components in good repair.
PELIGRO DE FLUIDO BAJO
ALTA PRESION
Para evitar heridas graves o la muerte:
1. Alivie la presión del sistema antes de
hacer repara ciones, ajustes o
desconecciones.
2. Use protección apropiada en las
manos y en los ojos, cuando revise
para ver si hay fugas. Utilice una tabla
o un cartón en vez de las manos.
3. Mantenga todos los componentes en
buen estado.
50530315-A
60 Parts
MAN0506 (Rev. 9/5/2008)
CENTER CUTTER KIT PARTS LIST
REF PART
QTY
DESCRIPTION
Quick coupler, male
REF PART
QTY
DESCRIPTION
17 90519003
18 90001115 *
2
2
1
2
3
4
6
7
8
9
1024671
1
1
1
1
6
6
1
1
1
2
2
3
2
2
2
Blade hub
3/8 NC x 1-3/4 HHCS GR5
1016161
1024674
1017719
58125 *
Motor housing
19
20
22
12169 *
66 *
2
3
4
1
1
2
3
4
1
1
3
3
2
2
3/8 NC x 1-1/4 HHCS GR5
5/16 NF x 1-1/2 HHCS GR5
3/8 NC Flange lock nut
Adapter, 1-5/16 ORBM x 3/4 NPTF
Decal, Hydraulic pressure
Decal, Rotating blades
1/2 NC x 1-1/4 Carriage bolt
1/2 NC Flange lock nut
1/2 NC x 1 HHCS GR5
1/2 Flat washer
Blade, .31 x 2.50 x 13.31 dbl edge
Hydraulic motor
14350 *
9/16 NC Lock nut
23 1023035
24 50530315
25 50530263
58452 *
9/16 NC x 1-1/2 HHCS GR8
Elbow, 1-1/16 ORBM x 3/4NPTF
Adapter, 3/4 NPTF x 3/4 NPTM
Elbow, 3/4 NPTM x 3/4 NPTF 90°
Hose, 40" x 3/4 NPTM x 3/4 NPTM
Tee, 3/4 NPTF
90503099
27309
29
30
31
32
33
34
35
301109 *
11900 *
25475 *
854 *
10 1023026
11 90506021
12 90503098
13 90501239
14 90503097
15 90506016
16 90501303
4378 *
2472 *
5283 *
5/16 Flat washer
Nipple, 3/4 NPTM
5/16 Lock washer
Check valve, 3/4 NPT
5/16 NF Hex nut
Hose, 114" x 3/4 NPTM x 3/4 NPTM
Adapter, 1/2 NPTM x 3/4 NPTF
36 1004695
Clamp, 1.94 dia Pipe
HHCS Hex Head Cap Screw
* Standard hardware, obtain locally
CENTER DEFLECTOR (OPTIONAL)
REF PART
QTY
DESCRIPTION
Center deflector
1
2
3
1016151
301109 *
11900 *
1
4
4
1/2 NC x 1-1/4 Carriage bolt GR5
1/2 NC Flange lock nut
*
Standard hardware, obtain locally
MAN0506 (Rev. 9/7/2011)
Parts 61
RUBBER FLAP
REF PART
QTY
DESCRIPTION
REF PART
QTY
DESCRIPTION
Flap rod (22 ft)
1
1
1
1
1
2
2
2
2
3
3
3
3
4
4
5
5
50531089
50531089
50531089
50531089
50531089
1022659
1022659
1022659
1022659
1022660
1022660
1022660
1022660
1022661
1022662
1022654
1022655
14 Rubber flap (12" - 15 ft)
18 Rubber flap (12" - 20 ft)
20 Rubber flap (12" - 22 ft)
24 Rubber flap (12" - 25 ft)
26 Rubber flap (12" - 27 ft)
5
5
5
6
7
8
8
8
8
8
9
9
9
9
9
1022656
1022657
1022658
1026528
1026529
2
2
2
2
2
Flap rod (25 ft)
Flap rod (27 ft)
Swing flap bar, mast plate (32" all)
Swing flap bar (32", 20 ft, 25 ft, 27 ft)
3
4
5
6
3
4
5
6
2
2
2
2
Flap bracket, right (15 ft)
Flap bracket, right (20 ft)
Flap bracket, right (22 ft & 25 ft)
Flap bracket, right (27 ft)
Flap bracket, left (15 ft)
Flap bracket, left (20 ft)
Flap bracket, left (22 ft & 25 ft)
Flap bracket, left (27 ft)
Rubber flap (2", 15 ft & 27 ft)
Rubber flap (8.5", 20 ft & 22 ft)
Flap rod (15 ft)
15028 * 20 3/8 NC x 1 Carriage bolt (15 ft)
15028 * 28 3/8 NC x 1 Carriage bolt (20 ft)
15028 * 32 3/8 NC x 1 Carriage bolt (22 ft)
15028 * 36 3/8 NC x 1 Carriage bolt (25 ft)
15028 * 40 3/8 NC x 1 Carriage bolt (27 ft)
14350 * 20 3/8 NC Flange lock nut (15 ft)
14350 * 28 3/8 NC Flange lock nut (20 ft)
14350 * 32 3/8 NC Flange lock nut (22 ft)
14350 * 36 3/8 NC Flange lock nut (25 ft)
14350 * 40 3/8 NC Flange lock nut (27 ft)
10 90023043 *
4
3/16 x 1-1/2 cotter pin
Flap rod (20 ft)
*
Standard hardware, obtain locally
62 Parts
MAN0506 (Rev. 9/5/2008)
BOLT TORQUE CHART
Always tighten hardware to these values unless a different torque value or tightening procedure is listed for a specific
application.
Fasteners must always be replaced with the same grade as specified in the manual parts list.
Always use the proper tool for tightening hardware: SAE for SAE hardware and Metric for metric hardware.
Make sure fastener threads are clean and you start thread engagement properly.
All torque values are given to specifications used on hardware defined by SAE J1701 MAR 99 & J1701M JUL 96.
SAE Bolt Head
Identification
SAE SERIES
TORQUE
CHART
A
SAE Grade 2
(No Dashes)
SAE Grade 8
(6 Radial Dashes)
SAE Grade 5
(3 Radial Dashes)
MARKING ON HEAD
SAE 5
A
SAE 2
SAE 8
Diameter
(Inches)
Wrench
Size
lbs-ft
N-m
8
lbs-ft
10
N-m
13
lbs-ft
14
N-m
1/4"
5/16"
3/8"
7/16"
1/2"
9/16"
5/8"
3/4"
7/8"
1"
7/16"
1/2"
6
18
37
12
17
19
26
27
9/16"
5/8"
23
31
35
47
49
67
36
48
55
75
78
106
163
232
325
569
907
1383
3/4"
55
75
85
115
164
230
403
642
979
120
171
240
420
669
1020
13/16"
15/16"
1-1/8"
1-5/16"
1-1/2"
78
106
149
261
416
634
121
170
297
474
722
110
192
306
467
METRIC SERIES
TORQUE
CHART
8.8
Metric Bolt Head
Identification
10.9
A
Metric
Grade 8.8
Metric
Grade 10.9
Coarse Thread
Marking on Head
Metric 8.8 Metric 10.9
Fine Thread
Marking on Head
Metric 8.8 Metric 10.9
A
A
Diameter &
Thread Pitch Wrench
(Millimeters)
Diameter &
Thread Pitch
(Millimeters)
Size
N-m
lbs-ft
6
N-m
lbs-ft
8
N-m
lbs-ft
6
N-m
lbs-ft
8
6 x 1.0
10 mm
13 mm
16 mm
18 mm
21 mm
24 mm
27 mm
30 mm
34 mm
36 mm
46 mm
8
11
27
8
11
29
6 x 1.0
8 x 1.0
8 x 1.25
10 x 1.5
12 x 1.75
14 x 2.0
16 x 2.0
18 x 2.5
20 x 2.5
22 x 2.5
24 x 3.0
30 x 3.0
20
15
20
21
16
22
39
29
54
40
41
30
57
42
10 x 1.25
12 x 1.25
14 x 1.5
16 x 1.5
18 x 1.5
20 x 1.5
22 x 1.5
24 x 2.0
30 x 2.0
68
50
94
70
75
55
103
163
250
363
507
684
861
1740
76
109
169
234
330
451
571
1175
80
151
234
323
457
623
790
1626
111
173
239
337
460
583
1199
118
181
263
367
495
623
1258
87
120
184
268
374
505
635
1283
125
172
244
332
421
867
133
194
270
365
459
928
Typical Washer
Installations
Bolt
Flat Washer
Lock Washer
8/9/00
Bolt Torque & Size Charts (Rev. 3/28/2007)
Appendix 63
BOLT SIZE CHART
NOTE: Chart shows bolt thread sizes and corresponding head (wrench) sizes for standard SAE and metric bolts.
SAE Bolt Thread Sizes
5/16
3/8
1/2
5/8
3/4
7/8
IN
1
2
7
3
4
5
6
MM
25
50
75
100
125
150
175
Metric Bolt Thread Sizes
8MM 10MM
12MM
14MM
16MM
18MM
ABBREVIATIONS
AG .............................................................. Agriculture
MPa ........................................................ Mega Pascal
N ......................................................................Newton
NC...................................................... National Coarse
NF...........................................................National Fine
NPSM .................... National Pipe Straight Mechanical
NPT...........................................National Pipe Tapered
NPT SWF......... National Pipe Tapered Swivel Female
ORBM...........................................O-Ring Boss - Male
P .......................................................................... Pitch
PBY.......................................................Power-Beyond
psi ......................................... Pounds per Square Inch
PTO......................................................Power Take Off
QD ................................................... Quick Disconnect
RH.............................................................. Right Hand
ROPS........................... Roll-Over Protective Structure
RPM........................................Revolutions Per Minute
RT ........................................................................Right
SAE.......................... Society of Automotive Engineers
UNC..................................................... Unified Coarse
UNF ..........................................................Unified Fine
UNS ..................................................... Unified Special
ASABE ....................American Society of Agricultural &
Biological Engineers (formerly ASAE)
ASAE....... American Society of Agricultural Engineers
ATF................................Automatic Transmission Fluid
BSPP............................. British Standard Pipe Parallel
BSPTM................ British Standard Pipe Tapered Male
CV ....................................................Constant Velocity
CCW.............................................. Counter-Clockwise
CW .............................................................. Clockwise
F.......................................................................Female
FT.............................................................. Full Thread
GA .....................................................................Gauge
GR (5, etc.)........................................... Grade (5, etc.)
HHCS ........................................Hex Head Cap Screw
HT ...........................................................Heat-Treated
JIC.................Joint Industry Council 37° Degree Flare
LH................................................................. Left Hand
LT ...........................................................................Left
m ........................................................................ Meter
mm ............................................................... Millimeter
M ..........................................................................Male
Bolt Torque & Size Charts (Rev. 3/28/2007)
64 Appendix
INDEX
ASSEMBLY
Dealer Set-Up Instructions 38
OPERATION (CONTINUED)
Optional Equipment
Optional Equipment
Additional Rear Wheels 23
Bed Cones for 3-Point Units 23
Rubber Flaps 23
Center Cut Kit Installation 42
Rubber Belting Installation 40
Rubber Flap Installation 40
Safety Light Kit Installation 40
Pre-Operation Check List
(Owner’s Responsibility) 15
Preparing for Operation 19
DEALER CHECK LISTS
Principal Components 14
Delivery Check List (Dealer’s Responsibility) 45
PTO Driveline Length (3-Point & 2-Point Models) 16
Removing Shredder from Tractor 19
Storage 23
Pre-Delivery Check List
(Dealer’s Responsibility) 45
GENERAL
Tractor horsepower vs. unit width (Table 1) 16
Abbreviations 62
Balance Statement 5
Bolt Size Chart 62
SAFETY
Check Lists
Bolt Torque Chart 61
Flail Pattern Worksheets 36
General Information 5
Introduction 2
Obtaining Replacement Manuals 2
Specifications 4
Table of Contents 3
Warranty
Product 65
Delivery (Dealer’s Responsibility) 45
Pre-Delivery (Dealer’s Responsibility) 45
Pre-Operation (Owner’s Responsibility) 15
Hazard Area 22
Operator Sign-Off Record 13
Safety Decals 10, 11, 12
Safety Rules 6, 7, 8, 9
Safety Symbols Explained 2
Replacement Parts 1
Worksheets for Contour Flail Patterns 36
SERVICE & MAINTENANCE
Balance Statement 5
Changing Gearbox Oil 28
Gearbox Oil Leakage 27
Greasing 24
OPERATION
Attaching Shredder to Tractor 17
Hydraulics (Center Cutter Option) 18
PTO Driveline 18
Lubricants 24
Pull-Type Model 18
Raising Stands 19
Lubrication Points Diagram 25
Lubrication Schedule 24
Lubrication Service Record 27
Mounting Clutch to Shredder 33
Ratchet Height Adjustment 29
Replacing Flail Knives 29
Replacing Rubber Shield Flaps 30
Replacing Stub Shaft 32
Servicing Rotors 30
With Quick Hitch 17
Without Quick Hitch 18
Break-In Period 14
Choosing the Correct Tractor 15
Cleaning 22
Field Operation 19
Flail Knives 20
Ground Speed 22
Removing Components 31
Replacing Components 31
Servicing Weasler Modular Friction Clutch 32
Wheel Spacing 29
Hazard Area 22
Setting Flail Height 21
Setting Operating Height 20
Setting Outer Trailing Wheels 21
Starting the Tractor 21
Stopping the Tractor 21
Turning 22
TROUBLESHOOTING 35
MAN0506 (Rev. 9/5/2008)
Index 65
WARRANTY
All Models Except Mow’n MachineTM Zero-Turn Mowers
Please Enter Information Below and Save for Future Reference.
Date Purchased: ____________________________
Model Number: ____________________________
From (Dealer): __________________________________________
Serial Number: __________________________________________
Woods Equipment Company (“WOODS”) warrants this product to be free from defect in material and workmanship. Except as otherwise set forth
below, the duration of this Warranty shall be for TWELVE (12) MONTHS COMMENCING ON THE DATE OF DELIVERY OF THE
PRODUCT TO THE ORIGINAL PURCHASER.
All current model loaders and backhoes are warranted for two (2) years from the date of delivery to the original purchaser.
The warranty periods for specific parts or conditions are listed below:
Part or
Condition
Warranted
Duration (from date of
delivery to the original
purchaser)
Model Number
Gearbox
Seals
All units listed below
2 years
BW1260, BW1620, BW1800, BW2400
8 years
7 years
BW240HD, BW180HD, BW180HB, BW126HB
BB48X, BB60X, BB72X, BB84X, BB600X, BB720X, BB840X, BB6000X, BB7200X, BB8400X,
DS1260, DSO1260, DS1440, TS1680, BW126-3, BW180-3, BW240
6 years
Gearbox
components PHD25, PHD35, PHD65, PHD95, 2162, 3240, DS96, DS120, RCC42, RM550-2, RM660-2,
RD990X, PRD6000, PRD7200, PRD8400, S15CD, S20CD, S22CD, S25CD, S27CD, BW180LH, 5 years
TC/R74, TC/R68, TC/R60, TBW144, TBW180, TBW204
3 years (1 year if used in rental or
commercial applications)
RDC54, RD60, RD72, TBW150C, TS/R60, TS/R52, TS/R44
Blade
spindles
RM550-2, RM660-2, RD990X, PRD6000, PRD7200, PRD8400, TBW144, TBW180, TBW204
BB600, BB720, BB840, BB6000, BB7200, BB8400, BW126-3, BW126HB, BW180-3, BW180HB,
3 years
Rust-through BW180HD, BW1260, BW1800, BW240, BW240HD, 2162, 3240, DS1260, DSO1260, DS1440, 10 years
TS1680
Under no circumstances will this Warranty apply in the event that the product, in the good faith opinion of WOODS, has been subjected to
improper operation, improper maintenance, misuse, or an accident. This Warranty does not apply in the event that the product has been materially
modified or repaired by someone other than WOODS, a WOODS authorized dealer or distributor, and/or a WOODS authorized service center.
This Warranty does not cover normal wear or tear, or normal maintenance items. This Warranty also does not cover repairs made with parts other
than those obtainable through WOODS.
This Warranty is extended solely to the original purchaser of the product. Should the original purchaser sell or otherwise transfer this product to a
third party, this Warranty does not transfer to the third party purchaser in any way. There are no third party beneficiaries of this Warranty.
WOODS makes no warranty, express or implied, with respect to engines, batteries, tires or other parts or accessories not manufactured by
WOODS. Warranties for these items, if any, are provided separately by their respective manufacturers.
WOODS’ obligation under this Warranty is limited to, at WOODS’ option, the repair or replacement, free of charge, of the product if WOODS, in
its sole discretion, deems it to be defective or in noncompliance with this Warranty. The product must be returned to WOODS with proof of
purchase within thirty (30) days after such defect or noncompliance is discovered or should have been discovered, routed through the
dealer and distributor from whom the purchase was made, transportation charges prepaid. WOODS shall complete such repair or
replacement within a reasonable time after WOODS receives the product. THERE ARE NO OTHER REMEDIES UNDER THIS WARRANTY.
THE REMEDY OF REPAIR OR REPLACEMENT IS THE SOLE AND EXCLUSIVE REMEDY UNDER THIS WARRANTY.
THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE OF THIS WARRANTY. WOODS
MAKES NO OTHER WARRANTY, EXPRESS OR IMPLIED, AND WOODS SPECIFICALLY DISCLAIMS ANY IMPLIED WARRANTY
OF MERCHANTABILITY AND/OR ANY IMPLIED WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE.
WOODS shall not be liable for any incidental or consequential losses, damages or expenses, arising directly or indirectly from the
product, whether such claim is based upon breach of contract, breach of warranty, negligence, strict liability in tort or any other legal
theory. Without limiting the generality of the foregoing, Woods specifically disclaims any damages relating to (i) lost profits, business, revenues
or goodwill; (ii) loss of crops; (iii) loss because of delay in harvesting; (iv) any expense or loss incurred for labor, supplies, substitute machinery or
rental; or (v) any other type of damage to property or economic loss.
This Warranty is subject to any existing conditions of supply which may directly affect WOODS’ ability to obtain materials or manufacture
replacement parts.
No agent, representative, dealer, distributor, serviceperson, salesperson, or employee of any company, including without limitation, WOODS, its
authorized dealers, distributors, and service centers, is authorized to alter, modify, or enlarge this
Warranty.
Answers
to
any
questions
regarding
warranty
service and locations may be obtained by contacting:
Woods Equipment
Company
2606 South Illinois Route 2
Post Office Box 1000
Oregon, Illinois 61061 USA
800-319-6637 tel
800-399-6637 fax
F-3079 (Rev. 2/14/2011)
WARRANTY
(Replacement Parts For All Models Except Mow’n Machine
TM
Zero-Turn Mowers)
Woods Equipment Company (“WOODS”) warrants this product to be free from defect in material and
workmanship for a period of ninety (90) days from the date of delivery of the product to the original
purchaser with the exception of V-belts, which will be free of defect in material and workmanship for a
period of 12 months.
Under no circumstances will this Warranty apply in the event that the product, in the good faith opinion of
WOODS, has been subjected to improper operation, improper maintenance, misuse, or an accident. This
Warranty does not cover normal wear or tear, or normal maintenance items.
This Warranty is extended solely to the original purchaser of the product. Should the original purchaser sell
or otherwise transfer this product to a third party, this Warranty does not transfer to the third party purchaser
in any way. There are no third party beneficiaries of this Warranty.
WOODS’ obligation under this Warranty is limited to, at WOODS’ option, the repair or replacement, free of
charge, of the product if WOODS, in its sole discretion, deems it to be defective or in noncompliance with
this Warranty. The product must be returned to WOODS with proof of purchase within thirty (30)
days after such defect or noncompliance is discovered or should have been discovered, routed through
the dealer and distributor from whom the purchase was made, transportation charges prepaid.
WOODS shall complete such repair or replacement within a reasonable time after WOODS receives the
product. THERE ARE NO OTHER REMEDIES UNDER THIS WARRANTY. THE REMEDY OF
REPAIR OR REPLACEMENT IS THE SOLE AND EXCLUSIVE REMEDY UNDER THIS
WARRANTY.
THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE OF
THIS WARRANTY. WOODS MAKES NO OTHER WARRANTY, EXPRESS OR IMPLIED, AND
WOODS SPECIFICALLY DISCLAIMS ANY IMPLIED WARRANTY OF MERCHANTABILITY AND/
OR ANY IMPLIED WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE.
WOODS shall not be liable for any incidental or consequential losses, damages or expenses, arising
directly or indirectly from the product, whether such claim is based upon breach of contract, breach
of warranty, negligence, strict liability in tort or any other legal theory. Without limiting the generality
of the foregoing, Woods specifically disclaims any damages relating to (i) lost profits, business, revenues or
goodwill; (ii) loss of crops; (iii) loss because of delay in harvesting; (iv) any expense or loss incurred for
labor, supplies, substitute machinery or rental; or (v) any other type of damage to property or economic loss.
This Warranty is subject to any existing conditions of supply which may directly affect WOODS’ ability to
obtain materials or manufacture replacement parts.
No agent, representative, dealer, distributor, service person, salesperson, or employee of any company,
including without limitation, WOODS, its authorized dealers, distributors, and service centers, is authorized
to alter, modify, or enlarge this Warranty.
Answers to any questions regarding warranty service and locations may be obtained by contacting:
F-8494 (Rev. 10/3/2011)
Woods Equipment
Company
2606 South Illinois Route 2
Post Office Box 1000
Oregon, Illinois 61061
800-319-6637 tel
800-399-6637 fax
©2006 Woods Equipment Company. All rights reserved. WOODS, the Woods logo, and “Tested. Proven. Unbeatable.” are trademarks of Woods
Equipment Company. All other trademarks, trade names, or service marks not owned by Woods Equipment Company that appear in this manual
are the property of their respective companies or mark holders. Specifications subject to change without notice.
|
Transcend Information StoreJet 18 mobile User Manual
Toshiba MK4018GAS (HDD2170) User Manual
Toshiba HDD2E64 User Manual
Sony ICF C263 User Manual
Sony CD Player D 151 User Manual
RCA SMARTSNOOZE RP5440 User Manual
Philips CDI 615 User Manual
Philips CD 605 User Manual
Panasonic CD Player SL MP73J User Manual
Oregon Scientific STARCK PS M03 User Manual