S.25O
SINGLE TOP LOADING CD PLAYER
USER MANUAL
IMPORTANT SAFETY INSTRUCTIONS
20. Accessories – Do not place this product on an
22. Replacement Parts – When replacement parts are
unstable cart, stand, tripod, bracket, or table. The
product may fall, causing serious injury to a child
or adult, and serious damage to the product. Use
only with a cart, stand, tripod, bracket, or table
recommended by the manufacturer, or sold with
the product. Any mounting of the product should
follow the manufacturer’s instructions, and should
use a mounting accessory recommended by the
manufacturer.
required, be sure the service technician has used
replacement parts specified by the manufacturer
or have the same characteristics as the original
part. Unauthorized substitutions may result in fire,
electric shock, or other hazards.
23. Safety Check – Upon completion of any service or
repairs to this product, ask the service technician
to perform safety checks to determine that the
product is in proper operating condition.
21. Lightning – For added protection for this product
during a lightning storm, or when it is left
unattended and unused for long periods of time,
unplug it from the wall outlet and disconnect the
antenna or cable system. This will prevent
damage to the product due to lightning and
power-line surges.
CAUTION
CAUTION: To reduce the risk of electric shock, do not remove
any cover. No user-serviceable parts inside. Refer servicing to
qualified service personnel only.
The lightning flash with arrowhead symbol within the equilateral triangle is intended to alert the use to
the presence of un-insulated “dangerous voltage” within the product’s enclosure that may be of
sufficient magnitude to constitute a risk of electric shock.
The exclamation point within the equilateral triangle is intended to alert the user to the presence of
important operation and maintenance (servicing) instructions in the literature accompanying this
appliance.
CAUTION
To prevent electric shock, do not use this polarized plug with an extension cord, receptacle or other outlet unless
the blades can be fully inserted to prevent blade exposure.
LINE VOLTAGE SELECTION
115V
1) The desired voltage may be set with the VOLTAGE SELECTOR switch on the rear panel of the
main unit, using a screwdriver.
2) Do not twist the VOLTAGE SELECTOR switch with excessive force as this may cause damage.
3) If the VOLTAGE SELECTOR switch does not move smoothly contact a qualified serviceman.
230V
NOTE ON USE
• Allow for sufficient heat dispersion when installed on a rack.
• Handle the power cord carefully.
• Hold the plug when unplugging the cord.
• Keep the set free from moisture, water, and dust.
• Unplug the power cord when not using the set for long periods of time.
• Do not obstruct the ventilation holes. (For sets with ventilation holes.)
• Do not let foreign objects in the set.
• Do not let insecticides, benzene, and thinner come in contact with the set.
• Never disassemble or modify the set in any way.
FUNCTIONS
1) EJECT: Opens the CD door
12) LOOP: Press once to set starting loop point, press
again set ending point and enter loop. Press a third
time to exit loop.
2) STOP: Stops the CD.
3) SKIP: Skips through the tracks on the CD, forward or
13) LCD DISPLAY: Shows time (minutes, seconds,
back.
frame), and pitch information.
4)
: Scans forward or back through the
14) PITCH FADER: Used to speed up or slow down cur-
current track. This unit features 3 scan speeds. Keep
rent track.
the
to change the scan speed.
5) PLAY/PAUSE: Plays or pauses the CD. Autocue func-
or
button pressed for a few seconds
15) AUDIO OUT: This stereo line output connects to the
line input on any DJ mixer.
tion sets the cue point automatically when this button is 16) DIGITAL OUTPUT: This coaxial (S/P DIF) digital out-
used.
put connects to any RCA S/P DIF input, as found on
most standard computer sound cards or CD burners.
6) CUE: Used to recall and preview the cue point.
17) FADER START: Connects to any DJ mixer equipped
with a fader start input. This enables the user to start
the CD from the cue point, using the mixer’s cross or
line fader, depending on the mixer.
7) TIME: LCD display reads the time remaining or time
elapsed, according to this button.
8) PITCH: Turns pitch fader ON and OFF.
9) PITCH SELECT: Pressing the PITCH and PITCH
BEND - (minus) buttons simultaneously changes the
pitch fader range between +/- 8, 12, and 16%.
18) VOLTAGE SELECTOR: Used to select the unit’s volt-
age according to the local setting. Note: The voltage
should preset correctly from the factory, however,
make sure to check it before powering the unit.
*Just for Dual Voltage model only.
10) PITCH BEND: Maximum pitch on this unit is 16%. If
the pitch fader is already physically set to 16%, this
function will not work.
19) AC IN: This is the connection for the supplied power
: Switches between Single or Continuous
11) SGL/CTN
cable.
play modes.
20) POWER: This button is used to power the unit ON and
OFF.
21) PHONES: Use this stereo jack to connect a pair
of headphones.
FUNCTIONS
1
2
14
13
E
L A P S
MA I N
I N G L E
E
D
R
E
S
C ON T I N U
3
4
12
11
10
5
6
7
8
9
21 15
16 17
18
19
20
SPECIFICATION
POWER SOURCE
Dual Voltage:
AC 115/230V, 50/60Hz
Single Voltage:
AC 100V, 50/60Hz (For Japan)
AC 110V, 60Hz (For Taiwan)
AC 120V, 60Hz (For U.S.A.,Canada,Mexico)
AC 220V, 50Hz (For United Arab Emirates,Chile,Aegentina)
AC 220V, 60Hz (For Philippines)
AC 230V, 50Hz (For Europe,New Zealand,South Africa,Singapore,Israel)
AC 240V, 50Hz (For Australia,U.K.)
DIMENSIONS
WEIGHT
216(W) x 275(H) x 88(D) mm
2.3Kgs
Stanton Magnetics, Inc. – Warranty Provision – Returns for Repairs or Replacement
WARRANTY
Through Stanton’s authorized dealers around the World, Stanton, or one of Stanton’s authorized distributors outside the U.S.,
will, without charge, repair or replace, at the sole discretion of the entity responsible for making the repair or providing the
replacement, any Stanton merchandise proved defective in material or workmanship for a period of one (1) year following the
date of original purchase. Exceptions to this warranty are as noted below:
The warranty for mechanical parts which are subject to wear and tear are limited to the earlier to occur of thirty (30) days
following the date of original purchase or the following number of cycles: Faders - 15,000; Rotary potentiometers - 10,000; and
Switches - 10,000.
Stanton will warrant all replacement parts and repairs for ninety (90) days from the date of original shipment. Repairs made
necessary by reason of misuse, alteration, normal wear, or accident are not covered under this warranty.
RETURNS
Authorized Stanton dealers are only authorized to sell and distribute merchandise within a specific country. All goods requiring
warranty repair or replacement must be returned (freight prepaid if not hand-delivered) to the authorized Stanton dealer from
whom the merchandise was purchased and in the same country where the merchandise was purchased. For purposes of
purchases made via the Internet, the merchandise must be returned to the authorized Stanton dealer in the country where the
authorized Stanton dealer which sold the merchandise to purchaser is located and not the authorized Stanton dealer in the
country where the purchaser is located or the country in which the merchandise was received. Any returns to a non-authorized
dealer or to an authorized Stanton dealer not in the same country as the merchandise was intended to be sold or as set forth
above will void this warranty.
To initiate a warranty repair, you must contact the authorized Stanton dealer from whom you purchased the merchandise, and
follow such authorized Stanton dealer’s return policy.
Stanton assumes no risk and shall be subject to no liability for damages or loss resulting from the specific use or application
made of the merchandise. Stanton's liability for any claim, whether based on breach of contract, negligence, infringement of any
rights of any party, or product liability, and relating to the merchandise shall not exceed the price received by Stanton from your
purchase of such merchandise. In no event will Stanton be liable for any special, incidental or consequential damages (including
loss of use, loss of profit and claims of third parties) however caused, whether by the negligence of Stanton or otherwise. To the
extent permitted by law and except as otherwise provided above, Stanton disclaims any express or implied warranties of
merchantability or fitness for a particular purpose.
The above warranty provides you with specific legal rights. You may also have additional rights, which are subject to variation
from state to state and country to country.
If there is a dispute regarding the warranty of merchandise that does not fall under the warranty conditions stated above, please
include a written explanation with the merchandise when returned pursuant to the terms and conditions set forth herein.
Stanton Magnetics, Inc, 3000 SW 42 St. Hollywood, Florida 33312.
c u t a l o n g d o t t e d l i n e
PLACE
STAMP
HERE
Stanton Magnetics, Inc.
3000 SW 42nd Street
Hollywood, FL 33312
U.S.A.
|