GSM REMOTE SUPERVISION
GB 051 Set for cellular phone Siemens C35i, M35 or S35
Automatic Information Transfer over the GSM Network
USER GUIDE
LEVEL
TABLE OF CONTENTS – GSM Remote Supervision GB 051
1. Product Description................................ ................................ ........................ 4
1.2. Contents of Delivery................................ ................................ ............... 5
2. Safety Commands ................................ ................................ ......................... 5
3. Installation and Setting into Operation................................ ............................ 6
3.1. Assembly of GSM Remote Supervision................................ ................... 6
3.2. Wiring and connecting the GSM Remote Supervision unit....................... 6
3.3. Inserting the SIM Card and Connecting to the Cell Phone....................... 7
3.4. Indication by LED ................................ ................................ ................... 9
4. Programming by SMS Messages................................ ................................ ... 9
4.1. PIN in GSM Remote Supervision................................ .......................... 10
4.2. RESET of GSM Remote Supervision................................ .................... 11
4.3. INIT – Re-initialization of Values Set from Production............................ 12
4.4. ICALL – Regular Calling Free of Charge................................ ............... 12
4.5. MCALL – Monthly Calling ................................ ................................ ..... 12
4.6. ACALL – Automatic Alarm Calling................................ ......................... 13
4.7. INFOSMS – Sending of Information Messages about Operation........... 13
4.8. SMSINT – Interval for Dispatch of SMS Messages about Operation...... 14
4.9. ALARMSMS – Alarm SMS Messages................................ ................... 14
4.10. OUT – Set-up of Level of Outputs by SMS messages ........................... 15
4.11. LIST – Detection of Set-up................................ ................................ .... 16
4.12. CALLBACK – Monitoring of Protected Area ................................ .......... 16
5. Programming from PC................................ ................................ .................. 17
6. Operation during Failure of External Power Supply................................ ....... 17
7. List of Programming Commands – Control SMS Messages.......................... 18
8. Basic Technical Parameters................................ ................................ ......... 19
GUARANTEE CERTIFICATE................................ ................................ ............ 20
GUARANTEE CONDITIONS................................ ................................ ............. 21
STATEMENT OF CONSENSUS................................ ................................ ....... 22
3
1. Product Description
1.1. Description of Function
GSM Remote Supervision GB 051 consists of plastic box, which is firmly joined to
the battery of cell phone. Communication cable with connector gets out of this box
into cell phone, which is used by GB 051 for realization of phone connection and
reception and sending of SMS messages.
On the upper side of the box there is a cut-off terminal board with terminals for
power supply, for interface to PC, control inputs and 8 input/output cables to alarm
switchboard, to detectors or to switching electronics.
Cable with a connector on the lower side of the box is intended for connecting a
mobile phone Siemens (one of those: C35i, M35, S35). There is also a connector
for data cable for connection to a PC that enables comfortable set up of required
configuration data. All configuration parameters can also be set using SMS
messages sent from a mobile phone or Internet.
Red light emitting diode (LED) on the left side signalizes basic operational states,
e.g.: correct function, function from backup power supply, GSM connection in
ready mode, action in progress, etc.
It is possible to prepare separate text of SMS message and to specify two
numbers of cell phones, to which message shall be sent for each of the 8 inputs.
Prepared text of SMS message is sent to specified numbers by activation of one
of the 8 inputs and phone call with warning alarm signal is carried out to a
predefined number. In case it is not possible to send SMS message or call, the
attempt is repeated 10 times in the intervals of 5 minutes.
Each input can be used at the same time as output and it is possible to set up
requested value of inputs using SMS message sent from cell phone or Internet.
It is possible to request call with additional sound monitoring of the room by
incoming SMS message.
It is still possible to use cell phone connected to GB 051 to carry out outgoing and
incoming calls.
GB 051 is self-controlled – it sends information about failure of power supply,
messages about reset, initialization, about configuration change but also
information messages about operation in set intervals.
4
1.2. Contents of Delivery
Sets
Label
Component description
GB 051 010
GB 051 011
SA 012 602
GSM Remote Control only
●
●
GSM Remote Control with the Siemens C35i mobile phone
AC/DC Adapter 220 V / 12 V DC, 600 mA, cable 1,5 m long
Connector
Siemens C35i mobile phone only
External FME antenna reduction cable for the
Siemens C35i mobile phone
●
●
●
●
●
●
●
○
●
○
13 004 027
13 004 028
○
○
○
○
○
○
○
○
○
○
○
○
ED 001 001
ED 001 002
External 3 dB antenna with magnet, 3 meter cable
Flat external antenna to be glued-on glass or plastic
Converter for connection between a PC and the GB
051 k PC, configuration software included
Connector reduction for the ED 050 001 converter
NiMH battery for the Siemens C35i mobile phone
Double power switch 230 V / 5 A
Motion detector
Motion detector with remote control
Push button connectable into a panel
○
○
○
○
ED 051 011
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
ED 051 050
01 002 008
ED 050 300
ED 050 400
ED 050 401
ED 060 601
Note:
(●) included in the predefined set
(○) optional accessory for the product type
2. Safety Commands
•
•
GB 051 is conformable with technical standards for operation in our mains.
Power source with voltage 10–16 V DC must be used for power supply. Dimension
for peak current is 500mA.
•
While cover is removed parts under voltage can be exposed. Device must be
disconnected from all power sources including backup battery before maintenance
or exchange of parts or filled boards.
•
•
While fitting together and assembling the equipment avoid cut-off of interconnecting
cables or their damage by edges.
No fluids must enter the device. Danger of fire, destruction of device or injury by
electric current impend. In case it occurs pull power source out of the plug
immediately and consult specialist.
•
•
Avoid forceful mechanic stress of device.
Do not place device into rooms with high temperatures, strong vibrations or high
humidity.
•
In case you moved device from cool to warm room do not set it into operation
immediately. Water condenses on device and operation under these circumstances
can cause damage of device. Let device warm up to temperature of room. Wait
until condensed water evaporates.
5
The GB 051 unit must be stocked always with the mobile phone connector
disconnected – when disconnected from external power supply, the GB 051 is
supplied from the mobile phone battery and the battery can be damaged by getting
completely flat.
!
3. Installation and Setting into Operation
3.1. Assembly of GSM Remote Supervision
GSM Remote Supervision by LEVEL is designed for operation in dry places.
During assembly avoid hot places and places where device would be exposed to
direct solar radiation or places close to heating elements.
Do not place GSM Remote Supervision or aerial mast close to phone exchange
or other electronic devices or lines. Due to high-frequency electromagnetic field
these devices could be interfered.
Due to interference it is not advisable to operate device close to other power or
high-frequency devices.
Before assembly prove by cell phone if there is sufficient level of signal required
by GSM network in selected place. Pay attention to delay in indicating of signal
level.
When using for protection of property, arrange protection of area against break-in
by detector.
3.2. Wiring and connecting the GSM Remote Supervision unit
Top view
Connector description
1) input/output No. 1
2) input/output No. 2
3) input/output No. 3
4) input/output No. 4
5) input/output No. 5
6) input/output No. 6
7) ground
8) input/output No. 7
9) input/output No. 8
10) power supply + 12 V
Bottom view
Connector description
1. Init
2. Ground
3. Reset
4. TxD
5. RxD
6. +Ucc
6
RESET By connection clips no. 2 and 3 (ground and reset) the unit reset will
be run, while all the set configuration value will remain in place.
The value of days in service will be set to 0.
INIT
Detailed description of how to carry on the initialization can be found
in Chapter 4.1. The GSM Remote Control device will be set into
default manufacturer’s settings by the initialization.
Recommended linkage of outputs:
Recommended linkage of inputs:
If GSM signal is insufficient external antenna can be connected to cell phone.
Professional solution of switching electrical devices on and off is provided by the
230 V/5 A double power switch ED 050 300 that can be purchased as optional
accessory.
For connection with a PC use always the ED 051 011 converter with cable that
connects into the connector at the bottom side of the unit and into the RS 232
interface in your PC. If you need to connect the PC using the older ED 050 001
converter, use the new optional accessory ED 051 050 (cable with reduction,
Control Panel software included).
The GB 051 device is able to work fully without external power supply for
approximately 12 hours being supplied from the mobile phone battery.
3.3. Inserting the SIM Card and Connecting to the Cell Phone
GSM Remote Supervision can be used only with cell phones Siemens C35, M35
and S35. Do not attempt to connect other phones, it may cause device or phone
damage.
Always use only NiMH battery with the GB 051. Using a Li-Ion battery might result
in unstable function of the GSM Remote Supervision; this type of battery can
cause the mobile phone to turn off without the possibility of starting up
automatically
7
Cell phone must be in basic configuration, only parameters specified further can
be changed.
A SIM card inserted in the GB 051 device must be configured in one of the two
ways described below:
a) If SIM is not blocked by PIN code, then the PIN value in GB 051 is irrelevant –
in this case you can skip this instruction and continue to
assembly the GB 051 and the cell phone.
b) If SIM is blocked by PIN, and then the PIN in GB 051 must be the same with
the PIN at the SIM in mobile phone. The default PIN code in the GB 051 unit
is set from production as “0000” (This will also be the PIN value after unit’s
initialization).
How to change PIN code in the Siemens mobile phones:
In menu select Setup – Security – Codes – Change PIN and the phone will ask
you to enter first the current PIN and then to enter and verify the new PIN code –
enter PIN “0000”.
Description of first assembly:
1. Insert the SIM card and battery into the cell phone, put on the back cover.
2. Stick the GB 051 unit together with the back cover of the mobile phone,
connectors must be faced down.
3. Interconnect the GB 051 with connector in the cell phone.
4. Connect the 12 V external power supply connector.
5. After the power supply is connected, the GB 051 will automatically turn on
the phone and if the PIN code is requested by the phone, the unit will
automatically enter the PIN predefined in configuration.
6. Wait to see the cell phone to connect to the GSM network, the LED should
start blinking slowly.
7. Following this it is recommended to send a command SMS as described
below to set a new PIN (other than 0000) in the GB 051 and the SIM card for
security reasons. This will also verify the correct functionality of the GB 051
device – by confirming it can receive the command SMS and set reply
message back.
After the inquiry on the phone display enter PIN with phone keyboard and wait
until phone logs in. From this moment GSM Remote Supervision is able to accept
control SMS messages.
Therefore send control message (command) to cell phone connected to GB 051:
XX0000PINVpppp
Where:
XX
means two capital letters X
0000
PIN
V
is the current PIN in GB 051 (manufacturer setting is 0000)
is the key word of the command
is the “space” symbol
pppp
is the new PIN value
8
If the PIN code on the SIM card is the same as the PIN in GB 051 and SIM is
blocked by PIN, then after setting new PIN to the GB 051 unit the PIN will be
changed in both – the SIM and GB 051 unit.
GB 051 replies to this SMS message and draws sender’s attention to necessity of
unification of PIN in Remote Supervision and phone and to necessity of switch-off
of cell phone.
After reception of this SMS message verify correct PIN code change by switching
the phone off with the red phone button. If PIN is set correctly and external power
supply is connected GB 051 automatically switches on the phone, sets PIN and
LED starts to flash in slow rhythm. It signalizes readiness of Remote Supervision
for reception and sending messages. At the same time new PIN is entered into
memory of GB 051.
It is possible to set up volume of cell phone ringing according to your need in
main menu. Ringing of the phone can be eventually switched off completely. It is
possible to change or switch off the sound indicating reception of SMS message
either. Furthermore, volume of conversation can be changed (only the volume of
speaker is concerned).
If SMS centre is not correctly set on SIM card it is necessary to set it up in cell
phone menu.
3.4. Indication by LED
Indicating LED on the side of GB 051 indicates basic operating states:
Slow regular flashing
Remote Supervision is prepared for operation
Occasional short flash Remote Supervision is prepared but runs from
backup battery
6 quick flashes
3 quick flashes
Quick flashing
Action in progress – after an input is activated
Incoming SMS command message
Not ready for ALARM, no connection to the GSM
4. Programming by SMS Messages
Number of functions and parameters, which allow adjustment of GSM Remote
Supervision to environment and user’s requirements can be configured by
programming. At the same time programming allows control of functions by user.
Programming can be carried out either remote by SMS message from cell phone or
Internet if available - or comfortably using the Control Panel software and the ED
051 011 communication converter with cable connected to the serial port of your PC.
9
Send a control SMS message from cell phone or Internet, which includes in text:
XXppppINSTRUCTIONVparameter
XX
Two capital letters X
pppp
Four digits of current PIN in GSM Remote Supervision
INSTRUCTION Key word of the command (no difference with capital or small
letters)
V
Space follows
parameter
Set-up value*
End of sequence by space or end of SMS message
One SMS can include up to 4 commands. The message then can look like this:
XXppppCOMMAND1Vparameter1VCOMMAND2Vparameter2VCOMMAND3Vparameter3V…
A confirming message is sent to the number the command message came from, this
message includes information about the new set parameter value.
4.1. PIN in GSM Remote Supervision
So as GSM Remote Supervision works correctly it is necessary that PIN on SIM
card corresponds with PIN of GSM gate and is different from 0000. In phone menu
SIM card must be blocked, tm. control of PIN after switch-on must be activated.
If the SIM card is blocked by a PIN code, connect the GB 051 to the mobile phone
only after the PIN in GB 051 was set to the same value – otherwise there is a
great risk of the SIM card getting blocked.
Change of PIN
Command*
pppp
XXppppPINVnnnn
Four digits of current PIN in GSM Remote Supervision
nnnn
Four digits of new PIN
* Space must be between the key word of command “PIN” and value of parameter “nnnn“
GB 051 confirms reception of Command to sender and draws his attention to
necessity of correspondence of PIN in GSM Remote Supervision and on SIM
card of cell phone. At the same time advises of necessity of switching off the
phone by red key. This way new PIN is entered into GSM Remote Supervision
memory and connected cell phone is automatically switched on.
Information about GB 051 reset and change of PIN is sent to INFOSMS number
after action is successfully carried out.
In case the PIN code is the same on the SIM card and in the GB 051 unit and the
SIM is blocked by PIN, then after entering a new PIN into GB 051 the PIN code
on the SIM card will be changed as well.
10
Value of PIN of GSM gate set from production and after initialization is 0000. PIN
0000 shall not be set into cell phone from gate so that blockage of phone is not
caused during first contacts with gate.
Example:
Original PIN of GSM gate is 0000. SIM card, which you use in cell phone in GSM
gate has PIN 1234 and is blocked by PIN.
Insert the SIM card into the mobile phone, but do not connect the GB 051
connector yet. Insert the required PIN in the mobile phone (e.g. 1234). Go into the
mobile phone menu and select Settings – Security – Codes – Change PIN then
insert the old PIN and the new PIN according to the mobile phone instructions.
Send a command SMS message with text XX0000PINV1234 from cell phone or
Internet on cell phone number in the unit.
As soon as a confirmation SMS message comes back to sender’s cell phone the
new PIN is set to value “1234”
User can verify the PIN change by switching the phone off.
Initialization:
In case you forget current PIN of GSM Remote Supervision you have no choice
than to carry out initialization of parameters to original set-up from production. It
shall be carried out in following steps:
1. Disconnect external power supply. (throw up power adapter)
2. Disconnect the mobile phone connector.
3. Interconnect inputs GROUND and INIT (terminals No. 1 and 2, see Chapter
3.2.) on terminal board
4. Connect external power supply. (throw in power adapter)
5. Remove connection GROUND – INIT
6. Disconnect external power supply. (throw up power adapter)
7. Connect the mobile phone to the GB 051 unit – the PIN must be preset to
value “0000”.
8. Connect external power supply.
9. PIN and other required parameters have to be set-up again
4.2. RESET of GSM Remote Supervision
If you want to carry out remote reset of counters of days and months in operation
then send SMS message with Command RESET. Command is rejected if GB 051
runs from backup battery.
Command
Pppp
XXppppRESET
Four digits of current PIN
Function is equivalent to disconnection of gate from power supply (also backup
one) and its re-connection.
11
4.3. INIT – Re-initialization of Values Set from Production
In case you lost view of GB 051 set-up you can carry out remote re-initialization of
parameter values set in production.
Command
Pppp
XXppppINIT
Four digits of current PIN
GSM Remote Supervision will be set to initial set-up from production.
Sender of Command receives message about correct reception of Command.
In case you do not know pre-set PIN or you are not able to program for another
reason then carry out hardware initialization described in chapter 4.1.
4.4. ICALL – Regular Calling Free of Charge
If you want to be informed free of charge about correct function of GB 051 in set
regular intervals following parameters provide it:
Command
Pppp
XXppppICALLVnumber *1)
Four digits of current PIN
Number
Maximum 14 digits of number of any phone which allows
display of caller’s number *2)
*1) The space is between key word of command „ICALL“ and value of parameter “number”
*2) Number can be entered in national format – e.g. 606445566 but also in international
format – e.g. +420606445566.
Command
Pppp
H
XXppppICALLINTVh *1)
Four digits of current PIN
Length of intervals in hours – time interval of two successive
calls. Value from 1 to 240 hours can be set. 168 hours set from
production.
*1) The space is between key word of command „ICALLINT“ and value of parameter „h“
After set-up of these parameters calling to set number will be automatically
activated. Phone rings only 5s and does not await pick-up. This way record about
calling from GB 051 is entered on display of cell phone without any charges
unless called party picks it up.
If you want to deactivate this functions set, send the command without parameter
– for example: XXppppICALL or XXpppICALLINT without further parameters.
4.5. MCALL – Monthly Calling
Some GSM operators require requires to carry out at least one paid phone
connection in 3 months from this card in order to keep the SIM card working –
otherwise the prepaid credit might expire. In order to prevent this from happening
it is possible to enter a number into GB 051, which the unit will automatically call
every month of operation, the phone call will be hung up 10 seconds after pick up.
12
Command
Pppp
Number
XXppppMCALLVnumber *1)
Four digits of current PIN
Maximum 14 digits of number of any phone *2)
*1) The space is between key word of command „MCALL“ and value of parameter „h“
*2) Number can be entered in national format – e.g. 606445566 but also in international
format – e.g. +420606445566. No number is activated from production.
After entering this parameter GB 051 calls set number once a month in order to
spend at least one tariff impulse.
If you want to use this service it is recommended to set-up number of your fax or
number of time information. It is not recommended to set your cell phone number
because GB 051 does not use real time and call can come during night.
If you want to deactivate this function set command without parameter – for
example XXppppMCALL without further parameters.
4.6. ACALL – Automatic Alarm Calling
By activation of any of SMS inputs set phone number is automatically chosen
together with sending SMS message. Dispatched SMS message can be
highlighted if you set ACALL number identical to SMSNO number or you can
report alarm on fixed phone lines where SMS messages cannot be received. After
answering warning tone is generated into speaking line.
Command
Pppp
XXppppACALLiVnumber *1)
Four digits of current PIN
i
Number of input: 1 to 8
Number
Maximum 14 digits of number of any phone which allows
display of caller’s number *2)
*1) The space is between key word of command „ACALLi“ and number
*2) Number can be entered in national format – e.g. 606445566 but also in international
format – e.g. +420606445566. No number is activated from production.
If you want to deactivate this function set command without parameter – tm.
XXppppACALLi without further parameters.
4.7. INFOSMS – Sending of Information Messages about Operation
GB 051 allows set-up of one cell phone number where all information SMS
messages about change of PIN, reset, initialization, power supply failure, change
in configuration, operation time and input activation are subsequently sent.
Command
XXppppINFOSMSVnumber (no number activated from
production) *1)
Pppp
Number
Four digits of current PIN
Maximum 14 digits of cell phone number *2)
*1) The space is between key word of command „INFOSMS“ and number
*2) Number can be entered in national format – e.g. 606445566 but also in international
format – e.g. +420606445566.
13
If you want to deactivate this function set command without parameter – tm.
XXppppINFOSMS without further parameters.
4.8. SMSINT – Interval for Dispatch of SMS Messages about Operation
Interval for sending regular SMS messages to INFOSMS number, which include
time of operation, can be set:
Command
XXppppSMSINTVn (interval of one day is set from production)
*1)
pppp
Four digits of current PIN
Number
Number from 1 to 30. It is interval for sending successive
message about operation.
*1) The space is between key word of command „SMSINT“ and value of parameter „n“
4.9. ALARMSMS – Alarm SMS Messages
When one of 8 inputs is activated GB 051 allows in addition to phone call to
common ACALL number also sending one of 8 prepared texts of SMS message
to two cell phone numbers.
Change of texts of SMS messages:
Order on the
terminal
Command *1)
Initial set-up
Input
board
XXppppSMSTXT1V“text“
XXppppSMSTXT2V“text“
XXppppSMSTXT3V“text“
XXppppSMSTXT4V text“
XXppppSMSTXT5V“text“
XXppppSMSTXT6V“text“
XXppppSMSTXT7V“text“
XXppppSMSTXT8V“text“
pppp
ALARM1
ALARM2
ALARM3
ALARM4
ALARM5
ALARM6
ALARM7
ALARM8
IO1
IO2
IO3
IO4
IO5
IO6
IO7
IO8
1
2
3
4
5
6
8
9
Four digits of current PIN
4 - 144 digits, always put in quotes, ?=question
text
*1) The space is between key word of command “SMSTXT” and “text”
Change of numbers for sending ALARM SMS messages
Text of SMS message No. 1, 2, 3, 4, 5, 6, 7 or 8 will be sent by activation of input
No. 1, 2, 3, 4, 5, 6, 7 or 8 (by connection with terminal No. 7 – ground) on terminal
board of GB 051. Each prepared text of SMS message of particular input can be
sent to two cell phone numbers.
No number is activated from production. These numbers can be set:
14
Activated by input
No.:
Order on the
terminal board
Command *1)
XXppppSMSNOA1Vnumber
XXppppSMSNOB1Vnumber
XXppppSMSNOA2Vnumber
XXppppSMSNOB2Vnumber
XXppppSMSNOA3Vnumber
XXppppSMSNOB3Vnumber
XXppppSMSNOA4Vnumber
XXppppSMSNOB4Vnumber
XXppppSMSNOA5Vnumber
XXppppSMSNOB5Vnumber
XXppppSMSNOA6Vnumber
XXppppSMSNOB6Vnumber
XXppppSMSNOB7Vnumber
XXppppSMSNOB7Vnumber
XXppppSMSNOB8Vnumber
XXppppSMSNOB8Vnumber
pppp
IO1
IO1
IO2
IO2
IO3
IO3
IO4
IO4
IO5
IO5
IO6
IO6
IO7
IO7
IO8
IO8
1
1
2
2
3
3
4
4
5
5
6
6
8
8
9
9
Four digits of current PIN
Maximum 14 digits of cell phone number
Number *2)
*1) The space is between key word of command and number
*2) Number can be entered in national format – e.g. 606445566 but also in international
format – e.g. +420606445566.
If you want to deactivate the number set command without number – tm. e.g.
XXppppSMSNOA3 without further parameters.
4.10. OUT – Set-up of Level of Outputs by SMS messages
Required logical level of outputs No. 1 to 8 can be set by incoming SMS
message. If output is set to logical value 0 it is not possible to activate it as input.
Order on the
terminal board
Command *1)
Output
XXppppOUT1Vy
XXppppOUT2Vy
XXppppOUT3Vy
XXppppOUT4Vy
XXppppOUT5Vy
XXppppOUT6Vy
XXppppOUT7Vy
XXppppOUT8Vy
pppp
IO1
IO2
IO3
IO4
IO5
IO6
IO7
IO8
1
2
3
4
5
6
8
9
Four digits of current PIN
y
Figure 0 or 1 determines logical level of output
By sending value 0 output is set to 0V
By sending value 1 output is set to 4-5V
*1) The space is between key word of command and value of parameter “y”
All outputs are set to logical level 1 (4–5 V) from production.
Inputs can be therefore activated.
15
If you only want to change value of output regardless of previous state send
command without parameter “y” – e.g. XXppppOUT5 changes value of output No.
5 to reverse.
Newly set actual values of all 8 inputs/outputs are sent back to sender and to
INFOSMS number.
4.11. LIST – Detection of Set-up
If you want to find out which values of parameters are set in GB 051 it is possible
to send control SMS message, which initiates sending messages with detailed
description of set-up back to sender.
Command
XXppppLISTVi *1)
pppp
i
Four digits of current PIN
IO number: 1 to 8, with no parameter will return the
shared configuration
*1) The space is between key word of command “LIST” and “i”
SMS command messages intended for getting parameter configuration of each
input/output 1–8:
The GB 051 unit will return sender a message with the required configuration
information related to the particular IO:
·
·
·
·
·
Actual value of logical level of the particular input.
Pre-set phone number for ALARM call.
Pre-set number A for ALARM SMS for the particular input.
Pre-set SMSNO B for the input.
Pre-set SMSTXT – text of the message of the input.
IO value, acall, aSMSnoA, aSMSnoB, SMStxt
In case the command SMS message is sent with no parameter, the GB 051 unit
will respond to the sender with message containing five basic configuration data:
infoSMS number, infoSMS interval, icall number, icall interval, mcall number
4.12. CALLBACK – Monitoring of Protected Area
If you want to find out by listening – e.g. during alarm – what is happening in
place of installation it is possible to require, by SMS message, to get further call
from GB 051 with switched-on microphone for room monitoring.
Command *1)
pppp
XXppppCALLBACKVnumber
Four digits of current PIN
Number
Maximum 14 digits of any phone number *2)
*1) The space is between key word of command „CALLBACK“ and number.
*2) If no number is specified GB 051 calls back the number of sender of SMS command.
Number can be entered in national format – e.g. 606445566 but also in international
format – e.g. +420606445566.
16
The call will take 255 seconds unless you end it sooner by hang-up.
Sensitivity of cell phone built-in microphone might be relatively low. Therefore it is
necessary to select a suitable placement of the unit in order to use this feature.
5. Programming from PC
Comfortable way of setting of all GB 051 parameters from PC by the means of
configuration program and serial cable with converter can be used. Program and cable
can be bought additionally as set for configuration from PC – supply No. ED 051 011.
Program shall be installed under MS WINDOWS by command A:\setup. Connect
GB 051 through interconnecting cable with converter ED 051 011. Program allows
reading of actual configuration from GB 051, changing of configuration and exporting of
new configuration into GB 051. Configuration can also be saved and read from files.
6. Operation during Failure of External Power Supply
During failure of external power supply GB 051 operates, with unchanged output, for
approx. 12 hours from battery. However, it is not able to switch on the cell phone
without external power supply and therefore command RESET is ignored.
Configuration, which you enter in GB 051, will be saved in memory – type EEPROM –
for arbitrarily long time even during disconnection or total discharge of backup battery.
17
7. List of Programming Commands – Control SMS Messages
Command XXpppp
Description
Range
Set
*1)
PINVnnnn
RESET
INIT
Set PIN
nnnn 4 digits of PIN
–
–
n= max. 14 digits
h= 1–240 (hours)
n= max. 14 digits
n= max. 14 digits
n= max. 14 digits
n= 1–255 (days)
0000
–
–
–
168
–
–
–
7
RESET of GSM Supervision
Initialisation of parameters
Regular information calling
Length of interval of calling
Monthly calling
ICALLVn
ICALLINTVh
MCALLVn
ACALLiVn
INFOSMSVn
SMSINTVn
Alarm calling
Information number
Interval of sending information
SMS messages
SMSTXT1V“text”
SMSTXT2V“text”
SMSTXT3V“text”
SMSTXT4V“text”
SMSTXT5V “text”
SMSTXT6V “text”
SMSTXT7V“text”
SMSTXT8V“text”
SMSNOA1Vn
SMSNOB1Vn
SMSNOA2Vn
SMSNOB2Vn
SMSNOA3Vn
SMSNOB3Vn
SMSNOA4Vn
SMSNOB4Vn
SMSNOA5Vn
SMSNOB5Vn
SMSNOA6Vn
SMSNOB6Vn
SMSNOA7Vn
SMSNOB7Vn
SMSNOA8Vn
SMSNOB8Vn
OUT1Vy
Alarm SMS messages
text of 4–144 digits put in ALARM1
“ ”
ALARM2
ALARM3
ALARM4
ALARM5
ALARM6
ALARM7
ALARM8
Numbers for
sending
ALARM SMS
messages
IO1 SMS n A
IO1 SMS n B
IO2 SMS n A
IO2 SMS n B
IO3 SMS n A
IO3 SMS n B
IO4 SMS n A
IO4 SMS n B
IO5 SMS n A
IO5 SMS n B
IO6 SMS n A
IO6 SMS n B
IO7 SMS n A
IO7 SMS n B
IO8 SMS n A
IO8 SMS n B
n= max. 14 digits
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
1
1
1
1
1
1
1
1
–
Set output No.1 (terminal No.1)
Set output No.2 (terminal No.2)
Set output No.3 (terminal No.3)
Set output No.4 (terminal No.4)
Set output No.5 (terminal No.5)
Set output No.6 (terminal No.6)
Set output No.7 (terminal No.8)
Set output No.8 (terminal No.9)
Find out set-up
y= 0 output in logical
value 0
y= 1 output in logical
value 1
without y – logical value
0
OUT2Vy
OUT3Vy
OUT4Vy
OUT5Vy
OUT6Vy
OUT7Vy
OUT8Vy
LISTVn
n= input No. 1 to 8
Without n – returns
common set-up
CALLBACKVn
Call with monitoring
n= max. 14 digits
Without no. calls back
–
*1) Always start with text XXpppp, where “pppp” is PIN of GB 051
18
8. Basic Technical Parameters
GB 051
ALARM tone
400 Hz
Inputs of SMS messages No. 1–8
Logical 0
Logical 1
0–0,5 V
4–6 V
Outputs of SMS messages No. 1–8
Logical 0
max. 0,8 V for Iz= 5 mA
Logical 1
3,5–4,5 V
for Iz= 0,03 mA
GSM network
GSM
SIM card
900/1800 MHz
Plug-in
Device
Power supply voltage
10–16 V DC
Peak power consumption during charging 350 mA (for 12 V)
Max. time of charging
Power consumption with charged battery
Time of operation from backup battery
Size
4 hours
< 20 mA
Min. 12 hours
65 × 70 × 17 mm
50 g
Weight
Operational temperatures
from +5 to +40 °C
19
GUARANTEE CERTIFICATE
Product name: ..........…....................... Type: …….....…………....................………..
Production number: .…...................…. Date of sale: .............…………........………..
Signature: …………….............………. Seller (stamp): ………………………………..
Information about guarantee repairs:
Date of
receipt
Date of
return
Signature
Description of defect
Producer: LEVEL ltd., Plhovská 1997, 547 01 Náchod. Czech Rep.
Tel/Fax No.: +420 491-44 66 11. e-mail: [email protected], www.levelna.cz
20
GUARANTEE CONDITIONS
Length of guarantee period is 24 months from the date of sale.
Guarantee applies only to goods registered or identified by company LEVEL.
Guarantee repair will be carried out at latest within 10 working days after receipt of
defective goods by company LEVEL provided that spare part is disposable in store. If it
is not possible alternative solution will be offered to user for time of repair.
Guarantee repairs will be carried out in company seat.
Technician is solely responsible for choosing the way of transport.
Guarantee is not provided in following cases:
Loss or replacement of Guarantee Certificate – or its additional correction.
Damage of device caused by natural disaster or damage of device during transport.
Damage caused by unsuitable positioning, unsuitable handling, operation of device in
unsuitable conditions.
Any unauthorized repair or adjustment carried out on device.
Damage or removal of sealing labels.
Guarantee does not apply to expendable property – dyeing ribbons, floppy discs, etc. It
does not apply to malfunction caused by installed software or interference, either.
Company is not responsible for possible losses, which originate from device failure
either.
Guarantee does not apply to malfunction caused by change of external conditions as
change in legislation, change of phone network, change of supply network, etc.
Guarantee is exerted by hand-over of completely filled-in Guarantee Certificate and
hand-over of device intended for repair including equipment.
21
STATEMENT OF CONSENSUS
We, LEVEL Ltd.., Plhovská 1997, 547 01 Náchod, Registration No.: 47469374, V.A.T.
No.: 243-47469374,
declare hereby our exclusive responsibility that hereinafter mentioned product meets
requirements of technical regulations, that product is save when used on specified
conditions and that we took all actions, which ensure consensus of all products of
hereinafter mentioned type placed on the market with technical documentation and with
requirements of relevant government regulation.
Product:
Type:
Remote Supervision
GB 051 010
Product is designed for telecommunication purposes
Way of consensus judging:
§12/4/a of law No.22/1997 of Col.
Above mentioned product is conformable with
and government regulation
§8 of law No.22/1997 of Col.
No.169/1997 of Col.
and standards for electromagnetic compatibility ČSN 342895; ČSN EN 55 022class B
and government regulation for electrical safety
No. 168/1997 of Col.
Additional information:
Power supply is carried out by safe voltage of 10–16 V (direct current) Device is
compatible only with cell phone Siemens C35, M35 and S35.
Released in:
Náchod
Name:
Ing. Michal Falta
Date of release:
01.08.2003 Function:
Managing Director
Stamp and signature:
22
23
|