Seagate SEATOOLS ST3500841ACE User Manual

DB35 Series 7200.2

ST3500841ACE

ST3400833ACE

ST3300822ACE

ST3250824ACE

ST3200827ACE

ST3160212ACE

ST3120213ACE

ST3802110ACE

Contents

1.0

2.0

Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Drive specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

2.1

2.2

Specification summary table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Formatted capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

2.2.1

LBA mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Default logical geometry . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Recording and interface technology . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Physical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Seek time. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Start/stop times . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Power specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Power consumption . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Conducted noise . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Voltage tolerance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Power-management mode s . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 5

2.9

Environmental specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Ambient temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Temperature gradient. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Humidity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Altitude . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Shock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Vibratio n . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 7

Acoustics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Electromagnetic immunity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Reliability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Agency certification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

2.13.1

2.13.2

2.13.3

Safety certification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Electromagnetic compatibility. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

FCC verification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

2.14

2.15

Environmental protectio n . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 0

2.14.1 European Union Restriction of Hazardous Substances (RoHS) . . . . . . . . . . . . 20

Corrosive environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

3.0

Configuring and mounting the drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

3.1

3.2

3.3

Handling and static discharge precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Breather filter hole precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Jumper settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Master/slave configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Cable-select option . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Alternate capacity jumper. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Ultra ATA/100 cabl e . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 6

3.4

Drive mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

4.0

5.0

ATA interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

4.1 ATA interface signals and connector pins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Supported ATA commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

Identify Device command. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

Set Features command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

S.M.A.R.T. command s . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 7

Seagate Technology support service s . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 9

DB35 Series 7200.2 Product Manual, Rev. C

List of Figures

Figure 7.

Typical 5V startup and operation current profil e . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 4

Typical 12V startup and operation current profil e . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 4

Breather filter hole locatio n . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 4

Master/slave jumper settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Ultra ATA cable connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Mounting dimensions—top, side and end view . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

I/O pins and supported ATA signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

DB35 Series 7200.2 Product Manual, Rev. C

iii

DB35 Series 7200.2 Product Manual, Rev. C

1.0

Introduction

This manual describes the functional, mechanical and interface specifications for the following Seagate^®DB35

Series 7200.2 model drives:

• ST3500841ACE

• ST3400833ACE

• ST3300822ACE

• ST3250824ACE

• ST3200827ACE

• ST3160212ACE

• ST3120213ACE

• ST3802110ACE

These drives provide the following key features:

• Minimal acoustics for consumer storage usage profile.

• Bedroom quiet performance.

• Optimized power for consumer storage devices.

• Spinup current limited to a maximum of 2 amps.

• 7,200-RPM spindle speed

• 8-Mbyte buffer: ST3500841ACE, ST3400833ACE, ST3300822ACE, ST3250824ACE, and ST3200827ACE.

• 2-Mbyte buffer: ST3160212ACE, ST3120213ACE, and ST3802110ACE.

• High instantaneous (burst) data transfer rates (up to 100 Mbytes per second) using Ultra DMA mode 5.

• Tunneling Giant magnetoresistive (TGMR) recording heads and EPRML technology, which provide the

drives with increased areal density.

• State-of-the-art cache and on-the-fly error-correction algorithms.

• Full-track multiple-sector transfer capability without local processor intervention.

• 350 Gs nonoperating shock.

• Support for S.M.A.R.T. drive monitoring and reporting.

• Support for Read Multiple and Write Multiple commands.

• Support for autodetection of master/slave drives that use cable select (CSEL).

• SeaTools diagnostic software performs a drive self-test that eliminates unnecessary drive returns.

• The 3D Defense System™, which includes Drive Defense, Data Defense, and Diagnostic Defense, offers

the industry’s most comprehensive protection for disc drives.

DB35 Series 7200.2 Product Manual, Rev. C

2.0

Drive specifications

Unless otherwise noted, all specifications are measured under ambient conditions, at 25°C, and nominal

power. For convenience, the phrases the drive and this drive are used throughout this manual to indicate the

following models:

ST3500841ACE

ST3400833ACE

ST3300822ACE

ST3250824ACE

ST3200827ACE

ST3160212ACE

ST3120213ACE

ST3802110ACE

2.1

Specification summary table

The specifications listed in this table are for quick reference. For details on specification measurement or defi-

nition, see the appropriate section of this manual.

DB35 Series 7200.2 Product Manual, Rev. C

Table 1:

Drive specifications for 500 and 400 Gbyte models

Drive specification

ST3500841ACE

ST3400833ACE

Formatted Gbytes (512 bytes/sector)*

Guaranteed sectors

500

400

976,773,168

512

781,422,768

Bytes per sector

Default sectors per track

Default read/write heads

Default cylinders

16,383

790.1

124.5

97.96

7,200

815.2

65.0

Recording density, KBPI (kbits/in max)

Track density, KTPI (ktracks/in max)

Areal density, (Gbits/in²max)

Spindle speed (RPM)

Internal data transfer rate (Mbits/sec max)

Sustained data transfer rate (Mbytes/sec max)

I/O data-transfer rate (Mbytes/sec max)

ATA data-transfer modes supported

100

PIO modes 0–4

Multiword DMA modes 0–2

Ultra DMA modes 0–5

Cache buffer

8 Mbytes

Height (mm max)

26.1 mm (1.028 inches)

Width (mm max)

101.6 mm (4.000 inches) +/- 0.010 inches

146.99 mm (5.787 inches)

710 grams (1.57 lb.)

4.16

Length (mm max)

Weight (typical)

Average latency (msec)

Power-on to ready (sec max)

Standby to ready (sec max)

Track-to-track seek time (msec typical)

Average seek (msec typical)

Startup current (typical) 12V (peak)

Seek power (typical)

16 sec

<0.8 (read), <1.0 (write)

18 (read), 20 (write)

2.0 amps

12.60 watts

Operating (Consumer Storage Profile)

Operating (PVR Storage Profile

Idle mode (typical)

9.20 watts

4.88 watts

8.00 watts

Standby mode (typical)

Sleep mode (typical)

0.80 watts

Voltage tolerance (including noise)

5V ± 5%

12V ± 10%

Ambient temperature

0° to 60°C (operating)

–40° to 70°C (nonoperating)

Temperature gradient (°C per hour max)

Relative humidity

20°C (operating)

30°C (nonoperating)

5% to 90% (operating)

5% to 95% (nonoperating)

Relative humidity gradient

30% per hour max

Wet bulb temperature (°C max)

37.7 (operating)

40.0 (nonoperating)

Altitude, operating

–60.96 m to 3,048 m

(–200 ft. to 10,000+ ft.)

Altitude, nonoperating (below mean sea level, max)

–60.96 m to 12,192 m

(–200 ft. to 40,000+ ft.)

DB35 Series 7200.2 Product Manual, Rev. C

Drive specification

ST3500841ACE

ST3400833ACE

Operational Shock (max at 2 msec)

Non-Operational Shock (max at 2 msec)

Vibration, operating

63 Gs

300 Gs

5-22 Hz: +/-0.25”, Displacement limited

22-350 Hz: 0.5 Gs

350-500 Hz: 0.25 Gs

Vibration, nonoperating

5-22 Hz: +/-0.25”, Displacement limited

22-350 Hz: 5.0 Gs

350-500 Hz: 1.0 Gs

Drive acoustics, sound power

Idle** (bels)

2.79 (typical)

2.96 (max)

2.59 (typical)

2.75 (max)

Operational, CE seeks (bels)

Operational, PVR seeks (bels)

2.82 (typical)

2.97 (max)

2.75 (typical)

2.90 (max)

2.71 (typical)

2.88 (max)

2.61 (typical)

2.75 (max)

Nonrecoverable read errors

Annualized Failure Rate (AFR)

Warranty

1 per 10¹⁴bits read

0.70%

5 years on distribution units.

To determine the warranty for a specific drive, use a web browser to access

the following web page:

www.seagate.com/support/service/

From this page, click on the “Verify Your Warranty” link. You will be asked to

provide the drive serial number, model number (or part number) and country

of purchase. The system will display the warranty information for your drive.

Contact start-stop cycles (25°C, 50% rel. humidity)

50,000

*One Gbyte equals one billion bytes when referring to hard drive capacity. Accessible capacity may vary depending on operating environment

and formatting.

**During periods of drive idle, some offline activity may occur according to the S.M.A.R.T. specification, which may increase acoustic and

power to operational levels.

DB35 Series 7200.2 Product Manual, Rev. C

Table 2:

Drive specifications for 300, 250, and 200 Gbyte models

Drive specification

ST3300822ACE

300

ST3250824ACE

250

ST3200827ACE

200

Formatted Gbytes (512 bytes/sector)*

Guaranteed sectors

586,072,368

512

488,397,168

390,721,968

Bytes per sector

Default sectors per track

Default read/write heads

Default cylinders

16,383

790.1

124.5

97.69

7,200

867.2

76.6

Recording density, KBPI (kbits/in max)

Track density, KTPI (ktracks/in max)

Areal density, (Gbits/in²max)

Spindle speed (RPM)

Internal data transfer rate (Mbits/sec max)

Sustained data transfer rate (Mbytes/sec max)

I/O data-transfer rate (Mbytes/sec max)

ATA data-transfer modes supported

100

PIO modes 0–4

Multiword DMA modes 0–2

Ultra DMA modes 0–5

Cache buffer

8 Mbytes

Height (mm max)

26.1 mm (1.028 inches)

Width (mm max)

101.6 mm (4.000 inches) +/- 0.010 inches

146.99 mm (5.787 inches)

Length (mm max)

Weight (typical)

655 grams (1.44 lb.)

4.16

580 grams (1.28 lb.)

Average latency (msec)

Power-on to ready (sec max)

Standby to ready (sec max)

Track-to-track seek time (msec typical)

Average seek (msec typical)

Startup current (typical) 12V (peak)

Seek power (typical)

16 sec

<0.8 (read), <1.0 (write)

18 (read), 20 (write)

2.0 amps

12.40 watts

9.25 watts

Operating (Consumer Storage Profile)

Operating (PVR Storage Profile

Idle mode (typical)

4.88 watts

8.00 watts

Standby mode (typical)

Sleep mode (typical)

0.80 watts

Voltage tolerance (including noise)

5V ± 5%

12V ± 10%

Ambient temperature

0° to 60°C (operating)

–40° to 70°C (nonoperating)

Temperature gradient (°C per hour max)

Relative humidity

20°C (operating)

30°C (nonoperating)

5% to 90% (operating)

5% to 95% (nonoperating)

Relative humidity gradient

30% per hour max

Wet bulb temperature (°C max)

37.7 (operating)

40 (nonoperating)

Altitude, operating

–60.96 m to 3,048 m

(–200 ft. to 10,000+ ft.)

Altitude, nonoperating (below mean sea level, max)

–60.96 m to 12,192 m

(–200 ft. to 40,000+ ft.)

DB35 Series 7200.2 Product Manual, Rev. C

Drive specification

ST3300822ACE

63 Gs

ST3250824ACE

ST3200827ACE

Operational Shock (max at 2 msec)

Non-Operational Shock (max at 2 msec)

Vibration, operating

350 Gs

5-22 Hz: 0.25 Gs, Limited displacement

22-350 Hz: 0.5 Gs

350-500 Hz: 0.25 Gs

Vibration, nonoperating

5–22 Hz: 0.25 Gs, Limited displacement

22-350 Hz: 5.0 Gs

350-500 Hz: 1.0 Gs

Drive acoustics, sound power

Idle* (bels)

2.67 (typical)

2.82 (max)

Operational, CE seeks (bels)

Operational, PVR seeks (bels)

2.80 (typical)

2.90 (max)

2.68 (typical

2.80 (max)

Nonrecoverable read errors

Annualized Failure Rate (AFR)

Warranty

1 per 10¹⁴bits read

0.70%

5 years on distribution units.

To determine the warranty for a specific drive, use a web browser to access

the following web page:

www.seagate.com/support/service/

From this page, click on the “Verify Your Warranty” link. You will be asked to

provide the drive serial number, model number (or part number) and country

of purchase. The system will display the warranty information for your drive.

Contact start-stop cycles (25°C, 50% rel. humidity)

50,000

*One Gbyte equals one billion bytes when referring to hard drive capacity. Accessible capacity may vary depending on operating environment

and formatting.

**During periods of drive idle, some offline activity may occur according to the S.M.A.R.T. specification, which may increase acoustic and

power to operational levels.

DB35 Series 7200.2 Product Manual, Rev. C

Table 3:

Drive specifications for 160, 120, and 80 Gbyte models

Drive specification

ST3160212ACE

160

ST3120213ACE

120

ST3802110ACE

Formatted Gbytes (512 bytes/sector)*

Guaranteed sectors

312,581,808

512

234,441,648

156,301,488

Bytes per sector

Default sectors per track

Default read/write heads

Default cylinders

16,383

840.0

141.5

119.0

Recording density, KBPI (kbits/in max)

Track density, KTPI (ktracks/in max)

Areal density, (Gbits/in²max)

Spindle speed (RPM)

7,200

867.2

83.0

Internal data transfer rate (Mbits/sec max)

Sustained data transfer rate (Mbytes/sec max)

I/O data-transfer rate (Mbytes/sec max)

ATA data-transfer modes supported

100

PIO modes 0–4

Multiword DMA modes 0–2

Ultra DMA modes 0–5

Cache buffer

2 Mbytes

Height (mm max)

26.1 mm (1.028 inches)

Width (mm max)

101.6 mm (4.000 inches) +/- 0.010 inches

146.99 mm (5.787 inches)

580 grams (1.28 lb.)

4.16

Length (mm max)

Weight (typical)

Average latency (msec)

Power-on to ready (sec max)

Standby to ready (sec max)

Track-to-track seek time (msec typical)

Average seek (msec typical)

Startup current (typical) 12V (peak)

Seek power (typical)

16 sec

<0.8 (read), <1.0 (write)

18 (read), 20 (write)

2.0 amps

12.40 watts

Operating (Consumer Storage Profile)

Operating (PVR Storage Profile

Idle mode (typical)

9.25 watts

4.91 watts

8.00 watts

Standby mode (typical)

Sleep mode (typical)

0.80 watts

Voltage tolerance (including noise)

5V ± 5%

12V ± 10%

Ambient temperature

0° to 60°C (operating)

–40° to 70°C (nonoperating)

Temperature gradient (°C per hour max)

Relative humidity

20°C (operating)

30°C (nonoperating)

5% to 90% (operating)

5% to 95% (nonoperating)

Relative humidity gradient

30% per hour max

Wet bulb temperature (°C max)

37.7 (operating)

40 (nonoperating)

Altitude, operating

–60.96 m to 3,048 m

(–200 ft. to 10,000+ ft.)

Altitude, nonoperating (below mean sea level, max)

–60.96 m to 12,192 m

(–200 ft. to 40,000+ ft.)

DB35 Series 7200.2 Product Manual, Rev. C

Drive specification

ST3160212ACE

63 Gs

ST3120213ACE

ST3802110ACE

Operational Shock (max at 2 msec)

Non-Operational Shock (max at 2 msec)

Vibration, operating

350 Gs

5-22 Hz: +/-0.25”, Displacement limited

22-350 Hz: 0.5 Gs

350-500 Hz: 0.25 Gs

Vibration, nonoperating

5-22 Hz: +/-0.25”, Displacement limited

22-350 Hz: 5.0 Gs

350-500 Hz: 1.0 Gs

Drive acoustics, sound power

Idle** (bels)

2.48 (typical)

2.64 (max)

2.46 (typical

2.65 (max)

2.43 (typical

2.51 (max)

Operational, CE seeks (bels)

Operational, PVR seeks (bels)

2.65 (typical)

2.95 (max)

2.57 (typical

2.64 (max)

2.61 (typical)

2.63 (max)

2.53 (typical)

2.62 (max)

2.50 (typical

2.57 (max)

2.45 (typical)

2.51 (max)

Nonrecoverable read errors

Annualized Failure Rate (AFR)

Warranty

1 per 10¹⁴bits read

0.70%

5 years on distribution units.

To determine the warranty for a specific drive, use a web browser to

access the following web page:

www.seagate.com/support/service/

From this page, click on the “Verify Your Warranty” link. You will be asked

to provide the drive serial number, model number (or part number) and

country of purchase. The system will display the warranty information for

your drive.

Contact start-stop cycles (25°C, 50% rel. humidity)

50,000

*One Gbyte equals one billion bytes when referring to hard drive capacity. Accessible capacity may vary depending on operating environment

and formatting.

**During periods of drive idle, some offline activity may occur according to the S.M.A.R.T. specification, which may increase acoustic and

power to operational levels.

DB35 Series 7200.2 Product Manual, Rev. C

2.2

Formatted capacity

Formatted

capacity*

Guaranteed

sectors

Model

Bytes per sector

ST3500841ACE

ST3400833ACE

ST3300822ACE

ST3250824ACE

ST3200827ACE

ST3160212ACE

ST3120213ACE

ST3802110ACE

500 Gbytes

400 Gbytes

300 Gbytes

250 Gbytes

200 Gbytes

160 Gbytes

120 Gbytes

80 Gbytes

976,773,168

781,422,768

586,072,368

488,397,168

390,721,968

312,581,808

234,441,648

156,301,488

512

*One Gbyte equals one billion bytes when referring to hard drive capacity. Accessible capacity may vary depending on operating environment

and formatting.

2.2.1

LBA mode

When addressing these drives in LBA mode, all blocks (sectors) are consecutively numbered from 0 to n–1,

where n is the number of guaranteed sectors as defined above.

See Section 4.1.2, "Identify Device command" (words 60-61 and 100-103) for additional information about 48-

bit addressing support of drives with capacities over 137 Gbytes.

2.3

Default logical geometry

Cylinders

Read/write heads

Sectors per track

16,383

LBA mode

When addressing these drives in LBA mode, all blocks (sectors) are consecutively numbered from 0 to n–1,

where n is the number of guaranteed sectors as defined above.

2.4

Recording and interface technology

Interface

ATA

Recording method

16/17 EPRML

Recording density KBPI (kbits/inch max)

ST3500841ACE, ST3400833ACE, ST3300822ACE,

ST3250824ACE, ST3200827ACE

790.1

840.0

ST3160212ACE, ST3120213ACE, ST3802110ACE

Track density KTPI (ktracks/inch max)

ST3500841ACE, ST3400833ACE, ST3300822ACE,

ST3250824ACE, ST3200827ACE

124.5

141.5

ST3160212ACE, ST3120213ACE, ST3802110ACE

Areal density (Gbits/inch max)

DB35 Series 7200.2 Product Manual, Rev. C

ST3500841ACE, ST3400833ACE, ST3300822ACE,

ST3250824ACE, ST3200827ACE

97.69

ST3160212ACE, ST3120213ACE, ST3802110ACE

Spindle speed (RPM) (± 0.2%)

119.0

7,200

Internal data-transfer rate (Mbits/sec max)

ST3500841ACE, ST3400833ACE

815.2

867.2

ST3300822ACE, ST3250824ACE, ST3200827ACE,

ST3160212ACE, ST3120213ACE, ST3802110ACE

Sustained data transfer rate (Mbytes/sec max)

ST3500841ACE, ST3400833ACE

65.0

ST3300822ACE, ST3250824ACE, ST3200827ACE

ST3160212ACE, ST3120213ACE, ST3802110ACE

I/O data-transfer rate (Mbytes/sec max)

Cache buffer

76.6

83.0

100 (Ultra DMA mode 5)

ST3500841ACE, ST3400833ACE, ST3300822ACE,

ST3250824ACE, ST3200827ACE

8 Mbytes (8,192 kbytes)

2 Mbytes (2,048 kbytes)

ST3160212ACE, ST3120213ACE, ST3802110ACE

DB35 Series 7200.2 Product Manual, Rev. C

2.5

Physical characteristics

Drive specification

Maximum height

Maximum width

Maximum length

Typical weight

(mm)

(inches)

26.1

1.028

(mm)

(inches)

101.6

4.000 ± 0.010

(mm)

(inches)

146.99

5.787

ST3500841ACE

ST3400833ACE

710 grams (1.57 lbs)

ST3300822ACE

655 grams (1.44 lbs)

580 grams (1.28 lbs)

ST3250824ACE

ST3200827ACE

ST3160212ACE

ST3120213ACE

ST3802110ACE

2.6

Seek time

Seek measurements are taken with nominal power at 25°C ambient temperature. All times are measured using

drive diagnostics. The specifications in the table below are defined as follows:

• Track-to-track seek time is an average of all possible single-track seeks in both directions.

• Average seek time is a true statistical random average of at least 5,000 measurements of seeks between

random tracks, less overhead.

Typical seek times (msec)

Track-to-track

Read

0.8

Write

1.0

Average

Average latency:

4.16

Note. These drives are designed to consistently meet the seek times represented in this manual. Physical seeks,

regardless of mode (such as track-to-track and average), are expected to meet or exceed the noted values.

However, due to the manner in which these drives are formatted, benchmark tests that include command

overhead or measure logical seeks may produce results that vary from these specifications.

2.7

Start/stop times

Power-on to Ready (sec)

Standby to Ready (sec)

16 (max)

10 (max)

Ready to spindle stop (sec)

DB35 Series 7200.2 Product Manual, Rev. C

2.8

Power specifications

The drive receives DC power (+5V and +12V) through a four-pin standard drive power connector.

2.8.1 Power consumption

Power requirements for the drives are listed in the table on page 13. Typical power measurements are based

on an average of drives tested, under nominal conditions, using +5.0V and +12.0V input voltage at 25°C ambi-

ent temperature.

• Spinup power

Spinup power is measured from the time of power-on to the time that the drive spindle reaches operating speed.

• Seek mode

During seek mode, the read/write actuator arm moves toward a specific position on the disc surface and does

not execute a read or write operation. Servo electronics are active. Seek mode power represents the worst-

case power consumption, using only random seeks with read or write latency time. This mode is not typical

and is provided for worst-case information.

• Operating power and current

Operating power is measured using a standard Consumer Storage Profile.

• Idle mode power

Idle mode power is measured with the drive up to speed, with servo electronics active and with the heads in

a random track location.

• Standby mode

During Standby mode, the drive accepts commands, but the drive is not spinning, and the servo and read/

write electronics are in power-down mode.

Table 4:

DC power requirements

Average

(watts, 25° C)

5V typ

amps

12V typ

amps

Power dissipation (watts)

Models

Spinup

Idle

All

—

2.0 (peak)

0.519

All

8.00

9.20

0.353

500GB, 400GB

Operating (Consumer Storage Profile)

Operating (PVR Storage Profile)

Seeking

0.587

0.39

0.520

0.41

300GB, 250GB, 200GB,

160GB, 120GB and 80GB

9.25

4.88

500GB, 400GB, 300GB,

250GB and 200GB

160GB, 120GB and 80GB

500GB, 400GB

4.91

12.60

0.613

0.795

300GB, 250GB, 200GB,

160GB, 120GB and 80GB

12.40

Standby

Sleep

All

0.80

0.106

0.023

DB35 Series 7200.2 Product Manual, Rev. C

2.8.1.1

Typical current profile

Figure 1

Typical 5V startup and operation current profile

Figure 2

2.8.2

Typical 12V startup and operation current profile

Conducted noise

Input noise ripple is measured at the host system power supply across an equivalent 80-ohm resistive load on

the +12 volt line or an equivalent 15-ohm resistive load on the +5 volt line.

• Using 12-volt power, the drive is expected to operate with a maximum of 120 mV peak-to-peak square-wave

injected noise at up to 10 MHz.

• Using 5-volt power, the drive is expected to operate with a maximum of 100 mV peak-to-peak square-wave

injected noise at up to 10 MHz.

Note. Equivalent resistance is calculated by dividing the nominal voltage by the typical RMS read/write

current.

2.8.3

Voltage tolerance

Voltage tolerance (including noise):

5V ± 5%

12V ± 10%

DB35 Series 7200.2 Product Manual, Rev. C

2.8.4

Power-management modes

The drive provides programmable power management to provide greater energy efficiency. In most systems,

you can control power management through the system setup program. The drive features the following

power-management modes:

Power mode

Active

Heads

Spindle

Rotating

Stopped

Buffer

Tracking

Parked

Enabled

Disabled

Idle

Standby

Sleep

• Active mode

The drive is in Active mode during the read/write and seek operations.

• Idle mode

The buffer remains enabled, and the drive accepts all commands and returns to Active mode any time disc

access is necessary.

• Standby mode

The drive enters Standby mode when the host sends a Standby Immediate command. If the host has set the

standby timer, the drive can also enter Standby mode automatically after the drive has been inactive for a

specifiable length of time. The standby timer delay is established using a Standby or Idle command. In Standby

mode, the drive buffer is enabled, the heads are parked and the spindle is at rest. The drive accepts all

commands and returns to Active mode any time disc access is necessary.

• Sleep mode

The drive enters Sleep mode after receiving a Sleep command from the host. In Sleep mode, the drive buffer

is disabled, the heads are parked and the spindle is at rest. The drive leaves Sleep mode after it receives a

Hard Reset or Soft Reset from the host. After receiving a reset, the drive exits Sleep mode and enters Standby

mode with all current translation parameters intact.

• Idle and Standby timers

Each time the drive performs an Active function (read, write or seek), the standby timer is reinitialized and

begins counting down from its specified delay times to zero. If the standby timer reaches zero before any drive

activity is required, the drive makes a transition to Standby mode. In both Idle and Standby mode, the drive

accepts all commands and returns to Active mode when disc access is necessary.

DB35 Series 7200.2 Product Manual, Rev. C

2.9

Environmental specifications

Ambient temperature

2.9.1

Ambient temperature is defined as the temperature of the environment immediately surrounding the drive.

Actual drive case temperature should not exceed 69°C (156°F) within the operating ambient conditions for

standard models. Recommended measurement locations are shown in See Figure 6 on page 27.

Above 1,000 feet (305 meters), the maximum temperature is derated linearly to 44°C (112°F) at 10,000 feet

(3,048 meters).

Operating:

0° to 60°C (32° to 140°F)

Nonoperating:

–40° to 70°C (–40° to 158°F)

2.9.2

Temperature gradient

Operating:

20°C per hour (68°F per hour max), without condensation

30°C per hour (86°F per hour max)

Nonoperating:

2.9.3

2.9.3.1

Humidity

Relative humidity

Operating:

Nonoperating:

5% to 90% noncondensing (30% per hour max)

5% to 95% noncondensing (30% per hour max)

2.9.3.2

Wet bulb temperature

Operating:

37.7°C (99.9°F max)

40°C (104°F max)

Nonoperating:

2.9.4

Altitude

Operating:

–60.96 m to 3,048 m (–200 ft. to 10,000+ ft.)

–60.96 m to 12,192 m (–200 ft. to 40,000+ ft.)

Nonoperating:

2.9.5

Shock

All shock specifications assume that the drive is mounted securely with the input shock applied at the drive

mounting screws. Shock may be applied in the X, Y or Z axis.

2.9.5.1

Operating shock

These drives comply with the performance levels specified in this document when subjected to a maximum

operating shock of 63 Gs based on half-sine shock pulses of 2 msec. Shocks should not be repeated more

than two times per second.

DB35 Series 7200.2 Product Manual, Rev. C

2.9.5.2

Nonoperating shock

The nonoperating shock level that the drive can experience without incurring physical damage or degradation

in performance when subsequently put into operation is 300 Gs for 500, 400, and 300 GB drives and 350 Gs

for 250, 200, 160, ad 80 GB drives, based on a nonrepetitive half-sine shock pulse of 2 msec duration.

2.9.6

Vibration

All vibration specifications assume that the drive is mounted securely with the input vibration applied at the

drive mounting screws. Vibration may be applied in the X, Y or Z axis.

2.9.6.1

Operating vibration

The following table lists the maximum vibration levels that the drive may experience while meeting the perfor-

mance standards specified in this document.

5–22 Hz

+/-0.25”, Displacement limited

22–350 Hz

350–500 Hz

0.50 Gs

0.25 Gs

2.9.6.2

Nonoperating vibration

The following table lists the maximum nonoperating vibration that the drive may experience without incurring

physical damage or degradation in performance when subsequently put into operation.

5–22 Hz

0.25 Gs (Limited displacement)

22–350 Hz

350–500 Hz

5.0 Gs

1.0 Gs

2.10

Acoustics

Drive acoustics are measured as overall A-weighted acoustic sound power levels (no pure tones). All mea-

surements are consistent with ISO document 7779. Sound power measurements are taken under essentially

free-field conditions over a reflecting plane. For all tests, the drive is oriented with the cover facing upward.

Note. For seek mode tests, the drive is placed in seek mode only. The number of seeks per second is defined

by the following equation:

(Number of seeks per second = 0.4 / (average latency + average access time)

Drive acoustics, sound power

Idle

Operational, CE seeks

Operational, PVR (Personal Video Recorder) seeks

2.46 bels (typ)

2.65 bels (max)

2.57 bels (typ)

2.64 bels (max)

2.50 bels (typ)

2.57 bels (max)

DB35 Series 7200.2 Product Manual, Rev. C

2.11

Electromagnetic immunity

When properly installed in a representative host system, the drive operates without errors or degradation in

performance when subjected to the radio frequency (RF) environments defined in the following table:

Table 5:

Radio frequency environments

Performance

level

Reference

standard

Test

Description

Electrostatic discharge

Radiated RF immunity

Contact, HCP, VCP: ± 4 kV; Air:

± 8 kV

EN 61000-4-2: 95

80 to 1,000 MHz, 3 V/m,

80% AM with 1 kHz sine

900 MHz, 3 V/m, 50% pulse

modulation @ 200 Hz

EN 61000-4-3: 96

ENV 50204: 95

Electrical fast transient

Surge immunity

± 1 kV on AC mains, ± 0.5 kV on

external I/O

EN 61000-4-4: 95

EN 61000-4-5: 95

EN 61000-4-6: 97

EN 61000-4-11: 94

± 1 kV differential, ± 2 kV com-

mon, AC mains

Conducted RF immunity

Voltage dips, interrupts

150 kHz to 80 MHz, 3 Vrms,

80% AM with 1 kHz sine

0% open, 5 seconds

0% short, 5 seconds

40%, 0.10 seconds

70%, 0.01 seconds

2.12

Reliability

Nonrecoverable read errors

Annualized Failure Rate (AFR)

Contact start-stop cycles

1 per 10 bits read, max.

0.70% (nominal power, 25°C ambient temperature)

50,000 cycles

(at nominal voltage and temperature, with 60 cycles per hour and a 50% duty cycle)

Preventive maintenance

None required

DB35 Series 7200.2 Product Manual, Rev. C

2.13

Agency certification

Safety certification

2.13.1

The drives are recognized in accordance with UL 1950 and CSA C22.2 (950) and meet all applicable sections

of IEC950 and EN 60950 as tested by TUV North America.

2.13.2

Electromagnetic compatibility

Hard drives that display the CE mark comply with the European Union (EU) requirements specified in the Elec-

tromagnetic Compatibility Directive (89/336/EEC). Testing is performed to the levels specified by the product

standards for Information Technology Equipment (ITE). Emission levels are defined by EN 55022, Class B and

the immunity levels are defined by EN 55024.

Seagate uses an independent laboratory to confirm compliance with the EC directives specified in the previous

paragraph. Drives are tested in representative end-user systems. Although CE-marked Seagate drives comply

with the directives when used in the test systems, we cannot guarantee that all systems will comply with the

directives. The drive is designed for operation inside a properly designed enclosure, with properly shielded I/O

cable (if necessary) and terminators on all unused I/O ports. Computer manufacturers and system integrators

should confirm EMC compliance and provide CE marking for their products.

Korean RRL

If these drives have the Korea Ministry of Information and Communication (MIC) logo, they comply with para-

graph 1 of Article 11 of the Electromagnetic Compatibility control Regulation and meet the Electromagnetic

Compatibility (EMC) Framework requirements of the Radio Research Laboratory (RRL) Ministry of Information

and Communication Republic of Korea.

These drives have been tested and comply with the Electromagnetic Interference/Electromagnetic Susceptibil-

ity (EMI/EMS) for Class B products. Drives are tested in a representative, end-user system by a Korean-recog-

nized lab.

• EUT name (model numbers): See table below.

• Certificate numbers:

Model

Certificate Number

E-H011-05-3453 (B)

ST3500841ACE

ST3400833ACE

ST3300822ACE

ST3250824ACE

ST3200827ACE

ST3160212ACE

ST3120213ACE

ST3802110ACE

• Trade name or applicant: Seagate Technology

• Manufacturing date: January 2006

• Manufacturer/nationality: Singapore and China

Australian C-Tick (N176)

If these models have the C-Tick marking, they comply with the Australia/New Zealand Standard AS/NZS3548

1995 and meet the Electromagnetic Compatibility (EMC) Framework requirements of the Australian Communi-

cation Authority (ACA).

DB35 Series 7200.2 Product Manual, Rev. C

2.13.3

FCC verification

These drives are intended to be contained solely within a personal computer or similar enclosure (not attached

as an external device). As such, each drive is considered to be a subassembly even when it is individually mar-

keted to the customer. As a subassembly, no Federal Communications Commission verification or certification

of the device is required.

Seagate Technology LLC has tested this device in enclosures as described above to ensure that the total

assembly (enclosure, disc drive, motherboard, power supply, etc.) does comply with the limits for a Class B

computing device, pursuant to Subpart J, Part 15 of the FCC rules. Operation with noncertified assemblies is

likely to result in interference to radio and television reception.

Radio and television interference. This equipment generates and uses radio frequency energy and if not

installed and used in strict accordance with the manufacturer’s instructions, may cause interference to radio

and television reception.

This equipment is designed to provide reasonable protection against such interference in a residential installa-

tion. However, there is no guarantee that interference will not occur in a particular installation. If this equipment

does cause interference to radio or television, which can be determined by turning the equipment on and off,

you are encouraged to try one or more of the following corrective measures:

• Reorient the receiving antenna.

• Move the device to one side or the other of the radio or TV.

• Move the device farther away from the radio or TV.

• Plug the computer into a different outlet so that the receiver and computer are on different branch outlets.

If necessary, you should consult your dealer or an experienced radio/television technician for additional sug-

gestions. You may find helpful the following booklet prepared by the Federal Communications Commission:

How to Identify and Resolve Radio-Television Interference Problems. This booklet is available from the Super-

intendent of Documents, U.S. Government Printing Office, Washington, DC 20402. Refer to publication num-

ber 004-000-00345-4.

2.14

Environmental protection

Seagate designs its products to meet environmental protection requirements worldwide, including regulations

restricting certain chemical substances.

2.14.1

European Union Restriction of Hazardous Substances (RoHS)

The European Union Restriction of Hazardous Substances (RoHS) Directive restricts the presence of chemical

substances, including Lead (Pb), in electronic products effective July 2006. Although amendments to the

Euro-pean Union’s Restriction of Hazardous Substances (RoHS) Directive have not been finalized, to the best

of our knowledge the disc drives documented in this publication will comply with the final RoHS Directive

require-ments.

A number of parts and materials in Seagate products are procured from external suppliers. We rely on the

rep-resentations of our suppliers regarding the presence of RoHS substances in these parts and materials. Our

supplier contracts require compliance with our chemical substance restrictions, and our suppliers document

their compliance with our requirements by providing material content declarations for all parts and materials for

the disc drives documented in this publication. Current supplier declarations include disclosure of the inclusion

of any RoHS-regulated substance in such parts or materials.

Seagate also has internal systems in place to ensure ongoing compliance with the RoHS Directive and all laws

and regulations which restrict chemical content in electronic products. These systems include standard

operat-ing procedures that ensure that restricted substances are not utilized in our manufacturing operations,

labora-tory analytical validation testing, and an internal auditing process to ensure that all standard operating

procedures are complied with.

DB35 Series 7200.2 Product Manual, Rev. C

2.15

Corrosive environment

Seagate electronic drive components pass accelerated corrosion testing equivalent to 10 years exposure to

light industrial environments containing sulfurous gases, chlorine and nitric oxide, classes G and H per ASTM

B845. However, this accelerated testing cannot duplicate every potential application environment. Users

should use caution exposing any electronic components to uncontrolled chemical pollutants and corrosive

chemicals as electronic drive component reliability can be affected by the installation environment. The silver,

copper, nickel and gold films used in Seagate products are especially sensitive to the presence of sulfide, chlo-

ride, and nitrate contaminants. Sulfur is found to be the most damaging. In addition, electronic components

should never be exposed to condensing water on the surface of the printed circuit board assembly (PCBA) or

exposed to an ambient relative humidity greater than 95%. Materials used in cabinet fabrication, such as vulca-

nized rubber, that can outgas corrosive compounds should be minimized or eliminated. The useful life of any

electronic equipment may be extended by replacing materials near circuitry with sulfide-free alternatives.

DB35 Series 7200.2 Product Manual, Rev. C

3.0

Configuring and mounting the drive

This section contains the specifications and instructions for configuring and mounting the drive.

3.1

Handling and static discharge precautions

After unpacking, and before installation, the drive may be exposed to potential handling and electrostatic dis-

charge (ESD) hazards. Observe the following standard handling and static-discharge precautions:

Caution:

• Keep the drive in the electrostatic discharge (ESD) bag until you are ready for installation.

• Before handling the drive, put on a grounded wrist strap, or ground yourself frequently by touching the metal

chassis of a computer that is plugged into a grounded outlet. Wear a grounded wrist strap throughout the

entire installation procedure.

• Handle the drive by its edges or frame only.

• The drive is extremely fragile—handle it with care. Do not press down on the drive top cover.

• Always rest the drive on a padded, antistatic surface until you mount it in the computer.

• Do not touch the connector pins or the printed circuit board.

• Do not remove the factory-installed labels from the drive or cover them with additional labels. Removal voids

the warranty. Some factory-installed labels contain information needed to service the drive. Other labels are

used to seal out dirt and contamination.

DB35 Series 7200.2 Product Manual, Rev. C

3.2

Breather filter hole precautions

This section contains information regarding the precautions which should be taken regarding the breather filter

hole in Seagate hard disc drives. Proper precautions should be taken to ensure full functionality and prevent

possible damage to the drive.

Breather hole

Do not cover or seal

this hole.

Figure 3

Breather filter hole location

Caution: Do not cover, seal, or insert any object into this hole.

This hole has two purposes:

• To allow condensation inside the hard disc to escape

• To allow air pressure inside the hard disc to equalize with ambient pressure

Note. If this hole is covered, sealed, or penetrated by any object, drive reliability may be compromised

and could lead to permanent damage—doing so voids the warranty.

DB35 Series 7200.2 Product Manual, Rev. C

3.3

Jumper settings

3.3.1

Master/slave configuration

The options jumper block shown in Figure 4 is used to configure the drive for operation. It is the 8-pin dual

header between the interface connector and the power connector. Use the following settings to configure the

drive as a master or a slave.

Master or single drive. The drive is configured at the factory for a master or single-drive operation with a

jumper set on pins 7 and 8.

Drive as slave. Remove all jumpers.

Drive as master with a non-ATA-compatible slave.

Use this jumper setting only if the drive does not work as a master with no jumpers installed.

Options jumper block

Master or single drive

Drive is slave

Master with non ATA-

compatible slave

Cable select

Limit drive capacity

to 32 Gbytes

Circuit Board

Figure 4

Master/slave jumper settings

3.3.2

Cable-select option

Computers that use cable select determine the master and slave drives by selecting or deselecting pin 28,

CSEL, on the interface bus. Master and slave drives are determined by their physical position on the cable. To

enable cable select, set a jumper on pins 5 and 6 as shown in Figure 4. Refer to your computer manual to

determine whether your computer supports this option.

3.3.3

Alternate capacity jumper

Some older computers may “hang” at startup if their BIOS detects a disc drive with a capacity greater than 32

Gbytes. This limits the drive’s capacity to 32 Gbytes when the alternate capacity jumper is used. To access the

full capacity of the drive, you can:

• Update the BIOS

• Use third-party software such as DiscWizard^™or Disk Manager

• Use a third-party host adapter

For drives with capacities greater than 32 Gbytes, the alternate capacity jumper changes the total available

LBA sectors to 32 Gbytes to solve issues with some BIOS during power on. The ATA Set Features subcom-

mand “F1 Report Full Capacity Available” causes Identify Data words 60 and 61 to report the full capacity.

See Section 4.1.3 on page 36 for more details on the Set Features command.

DB35 Series 7200.2 Product Manual, Rev. C

Windows XP, Windows Me, Windows 98 or newer versions are needed to support drives with capacities

greater than 32 Gbytes.

3.3.4

Ultra ATA/100 cable

An 80-conductor 40-pin cable is required to run Ultra DMA mode 3, mode 4 and mode 5. This cable uses even-

numbered conductors connected to the ground pins to improve signal integrity.

Note. If you are using a 40-pin, 80-conductor

cable, attach the blue connector to the

motherboard, the black connector to the

master drive, and the gray connector

to the slave.

Master

Pin 1

Computer

Motherboard

Slave

Figure 5

Ultra ATA cable connectors

Note. The drive supports both host and drive cable detection. The host detects the 80-conductor cable by

sampling pin 34, CBLID–, on the interface bus. The drive detects the 80-conductor cable by sens-

ing a capacitor at the host side through the CBLID– signal. The result is reported in a Fast Rise

Detected bit (bit 13 of word 93 in the Identify drive parameter block).

3.4

Drive mounting

You can mount the drive in any orientation using four screws in the side-mounting holes or four screws in the

bottom-mounting holes. See Figure 6 for drive mounting dimensions. Follow these important mounting precau-

tions when mounting the drive:

• Allow a minimum clearance of 0.030 inches (0.76 mm) around the entire perimeter of the drive for cooling.

• Use only 6-32 UNC mounting screws.

• Do not overtighten the mounting screws (maximum torque: 6 inch-lb.).

• Do not use a drive interface cable that is more than 18 inches long.

DB35 Series 7200.2 Product Manual, Rev. C

Notes:

1. Dimensions are shown in inches (mm).

2 Dimensions per SFF-8301 specification.

0.228

(5.79)

0.178

(4.27)

2.23

(56.56)

1.028 max

(26.11)

2.83

(71.80)

3 x 0.25 0.010

(6.35 0.037)

both sides

3.71

(94.35)

1.122 0.02

(28.5 0.51)

1.625 0.020

(41.28 0.51)

1.638 0.01

(41.61 0.25)

5.787 max

(146.99)

1.75 0.01

(44.45 0.25)

4.0 0.01

(101.60 0.25)

4 x 6-32 UNC-2B

0.150 (3.81) max. fastener

penetration. 3 threads

minimum engagement.

3 x 6-32 UNC-2B

0.1240 0.01

(3.18 0.25)

0.150 (3.81) max. fastener

penetration both sides. 3 threads

minimum engagement.

Recommended

case temperature

measurement location

case temperature

measurement location

3.750 0.01

(95.25 0.25)

4.0 0.01

(101.60 0.25)

Figure 6

Mounting dimensions—top, side and end view

DB35 Series 7200.2 Product Manual, Rev. C

4.0

ATA interface

These drives use the industry-standard ATA task file interface that supports 16-bit data transfers. It supports

ATA programmed input/output (PIO) modes 0–4; multiword DMA modes 0–2, and Ultra DMA modes 0–5. The

drive also supports the use of the IORDY signal to provide reliable high-speed data transfers.

You can use a daisy-chain cable to connect two drives to a single AT host bus. For detailed information about

the ATA interface, refer to the draft of AT Attachment with Packet Interface Extension (ATA/ATAPI-7), NCITS

T13 1410D, subsequently referred to as the Draft ATA-7 Standard.

4.1

ATA interface signals and connector pins

Figure 7 summarizes the signals on the ATA interface connector that the drive supports. For a detailed descrip-

tion of these signals, refer to the Draft ATA-7 Standard.

Drive pin #

Host pin # and signal description

Signal name

–

Reset

Hardware Reset

Ground

DD7

Ground

Host Data Bus Bit 7

Host Data Bus Bit 8

Host Data Bus Bit 6

Host Data Bus Bit 9

Host Data Bus Bit 5

Host Data Bus Bit 10

Host Data Bus Bit 4

DD8

DD6

DD9

DD5

DD10

DD4

DD11

DD3

10 Host Data Bus Bit 11

11 Host Data Bus Bit 3

12 Host Data Bus Bit 12

13 Host Data Bus Bit 2

14 Host Data Bus Bit 13

15 Host Data Bus Bit 1

16 Host Data Bus Bit 14

17 Host Data Bus Bit 0

18 Device Data (15:0)

19 Ground

DD12

DD2

DD13

DD1

DD14

DD0

DD15

Ground

(removed)

DMARQ

Ground

DIOW–

STOP

Ground

(No Pin)

21 DMA Request

22 Ground

23 Device I/O Write:

Stop Ultra DMA Burst

24 Ground

DIOR

–

25 Device I/O Read:

Host Ultra DMA Ready:

Host Ultra DMA Data Strobe

26 Ground

27 I/O Channel Ready

Device Ultra DMA Ready

Device Ulta DMA Data Strobe

28 Cable Select

29 DMA Acknowledge

30 Ground

31 Device Interrupt

32 Reserved

33 Host Address Bus Bit 1

34 Passed Diagnostics

Cable Assembly Type Identifier

35 Device Address (2:0)

36 Device Address (2:0)

37 Chip Select (1:0)

38 Chip Select (1:0)

39 Drive Active/Slave Present

40 Ground

HDMARDY

–

HSTROBE

Ground

IORDY

DDMARDY–

DSTROBE

CSEL

–

DMACK

Ground

INTRQ

–

IOCS16

DA1

PDIAG

–

CBLID–

DA0

DA2

–

CS0

CS1

–

DASP

Ground

Pins 28, 34 and 39 are used for master-slave communication (details shown below).

Drive 1 (slave)

Drive 0 (master)

Host

CSEL

–

PDIAG

DASP–

Figure 7

I/O pins and supported ATA signals

DB35 Series 7200.2 Product Manual, Rev. C

4.1.1

Supported ATA commands

The following table lists ATA-standard commands that the drive supports. For a detailed description of the ATA

commands, refer to the Draft ATA-7 Standard. See “S.M.A.R.T . c ommands” on page 37 for details and sub-

commands used in the S.M.A.R.T. implementation.

Table 6:

Supported ATA commands

Command name

Command code (in hex)

98 or E5

Check Power Mode

Device Configuration Freeze Lock

Device Configuration Identify

Device Configuration Restore

Device Configuration Set

Device Reset

B1 / C1

B1 / C2

B1 / C0

B1 / C3

Download Microcode

Execute Device Diagnostics

Flush Cache

Flush Cache Extended

Format Track

Identify Device

Idle

97 or E3

Idle Immediate

95 or E1

Initialize Device Parameters

Read Buffer

Read DMA

Read DMA Extended

Read DMA Without Retries

Read Log Ext

Read Multiple

Read Multiple Extended

Read Native Max Address

Read Native Max Address Extended

Read Sectors

Read Sectors Extended

Read Sectors Without Retries

Read Verify Sectors

Read Verify Sectors Extended

Read Verify Sectors Without Retries

Recalibrate

DB35 Series 7200.2 Product Manual, Rev. C

Command name

Security Disable Password

Security Erase Prepare

Security Erase Unit

Security Freeze

Command code (in hex)

Security Set Password

Security Unlock

Seek

Set Features

Set Max Address

Note: Individual Set Max Address

commands are identified by the value

placed in the Set Max Features regis-

ter as defined to the right.

Address:

Password:

Lock:

Unlock:

Freeze Lock:

Set Max Address Extended

Set Multiple Mode

Sleep

99 or E6

S.M.A.R.T. Disable Operations

S.M.A.R.T. Enable/Disable Autosave

S.M.A.R.T. Enable Operations

S.M.A.R.T. Execute Offline

S.M.A.R.T. Read Attribute Thresholds

S.M.A.R.T. Read Data

S.M.A.R.T. Read Log Sector

S.M.A.R.T. Return Status

S.M.A.R.T. Save Attribute Values

S.M.A.R.T. Write Log Sector

Standby

B0 / D9

B0 / D2

B0 / D8

B0 / D4

B0 / D1

B0 / D0

B0 / D5

B0 / DA

B0 / D3

B0 / D6

96 or E2

Standby Immediate

94 or E0

Write Buffer

Write DMA

Write DMA Extended

Write DMA Without Retries

Write Log Extended

Write Multiple

Write Multiple Extended

Write Sectors

DB35 Series 7200.2 Product Manual, Rev. C

Command name

Command code (in hex)

Write Sectors Without Retries

Write Sectors Extended

DB35 Series 7200.2 Product Manual, Rev. C

4.1.2

Identify Device command

The Identify Device command (command code EC ) transfers information about the drive to the host following

power up. The data is organized as a single 512-byte block of data, whose contents are shown in the T a ble 6

on page 30. All reserved bits or words should be set to zero. Parameters listed with an “x” are drive-specific or

vary with the state of the drive. See Section 2.0 on page 3 for default parameter settings.

The following commands contain drive-specific features that may not be included in the Draft ATA-7 Standard.

Word

Description

Value

Configuration information:

• Bit 15: 0 = ATA; 1 = ATAPI

• Bit 7: removable media

• Bit 6: removable controller

• Bit 0: reserved

0C5A

Number of logical cylinders

16,383

ATA-reserved

0000

Number of logical heads

Retired

0000

Retired

Number of logical sectors per logical track: 63

Retired

003F

7–9

10–19

0000

Serial number: (20 ASCII characters, 0000 = none)

ASCII

Retired

Obsolete

0000

0400

0000

x.xx

23–26

Firmware revision (8 ASCII character string, padded with blanks to

end of string)

27–46

Drive model number

(40 ASCII characters, padded with blanks to end of string)

ST3500841ACE

ST3400833ACE

ST3300822ACE

ST3250824ACE

ST3200827ACE

ST3160212ACE

ST3120213ACE

ST3802110ACE

(Bits 7–0) Maximum sectors per interrupt on Read multiple and Write

multiple (16)

8010

Reserved

0000

Standard Standby timer, IORDY supported and may be disabled

ATA-reserved

2F00

0000

0200

0007

PIO data-transfer cycle timing mode

Retired

Words 54–58, 64–70 and 88 are valid

Number of current logical cylinders

Number of current logical heads

xxxx

DB35 Series 7200.2 Product Manual, Rev. C

Word

Description

Value

Number of current logical sectors per logical track

Current capacity in sectors

xxxx

57–58

Number of sectors transferred during a Read Multiple or Write Multi-

ple command

60–61

Total number of user-addressable LBA sectors available

(see Section 2.2 for related information)

ST3500841ACE = 0FFFFFFFh*

ST3400833ACE = 0FFFFFFFh*

ST3300822ACE = 0FFFFFFFh*

ST3250824ACE = 0FFFFFFFh*

ST3200827ACE = 0FFFFFFFh*

ST3160212ACE = 0FFFFFFFh*

ST3120213ACE = DF94BB0h*

ST3802110ACE = 950F8B0h*

*Note: The maximum value allowed in this field is: 0FFFFFFFh

(268,435,455 sectors, 137 Gbytes). Drives with capacities over 137

Gbytes will have 0FFFFFFFh in this field and the actual number of

user-addressable LBAs specified in words 100-103. This is required

for drives that support the 48-bit addressing feature.

Retired

0000

Multiword DMA active and modes supported

(see note following this table)

xx07

Advanced PIO modes supported (modes 3 and 4 supported)

Minimum multiword DMA transfer cycle time per word (120 nsec)

0003

0078

Recommended multiword DMA transfer cycle time per word (120

nsec)

Minimum PIO cycle time without IORDY flow control (240 nsec)

Minimum PIO cycle time with IORDY flow control (120 nsec)

ATA-reserved

00F0

0078

0000

69–74

Queue depth

76–79

SATA-reserved

xxxx

Major version number

007E

Minor version number

0000

Command sets supported

346B

Command sets supported

7D01

Command sets support extension

Command sets enabled

4003

34xx

Command sets enabled

3xxx

Command sets enable extension

4003

Ultra DMA support and current mode

(see note following this table)

xx3F

Security erase time

0000

Enhanced security erase time

Master password revision code

Hardware reset value (see description following this table)

ATA-reserved

FFFE

xxxx

95–99

0000

DB35 Series 7200.2 Product Manual, Rev. C

Word

Description

Value

ST3500841ACE = 976,773,168

ST3400833ACE = 781,422,768

ST3300822ACE = 586,072,368

ST3250824ACE = 488,397,168

ST3200827ACE = 390,721,968

ST3160212ACE = 312,581,808

ST3120213ACE = 234,441,648

ST3802110ACE = 156,301,488

100–103

Total number of user-addressable LBA sectors available

(see Section 2.2 for related information)

These words are required for drives that support the 48-bit addressing

feature. Maximum value: 0000FFFFFFFFFFFFh.

104–127

128

ATA-reserved

Security status

Seagate-reserved

ATA-reserved

Integrity word

0000

0001

129–159

160–254

255

xxxx

0000

xxA5

Note. Advanced Power Management (APM) and Automatic Acoustic Management (AAM) features are not supported

Note. See the bit descriptions below for words 63, 88, and 93 of the Identify Drive data:

Description (if bit is set to 1)

Bit

Word 63

Multiword DMA mode 0 is supported.

Multiword DMA mode 1 is supported.

Multiword DMA mode 2 is supported.

Multiword DMA mode 0 is currently active.

Multiword DMA mode 1 is currently active.

Multiword DMA mode 2 is currently active.

Word 88

Bit

Ultra DMA mode 0 is supported.

Ultra DMA mode 1 is supported.

Ultra DMA mode 2 is supported.

Ultra DMA mode 3 is supported.

Ultra DMA mode 4 is supported.

Ultra DMA mode 0 is currently active.

Ultra DMA mode 1 is currently active.

Ultra DMA mode 2 is currently active.

Ultra DMA mode 3 is currently active.

Ultra DMA mode 4 is currently active.

Ultra DMA mode 5 is currently active.

Word 93

Bit

1 = 80-conductor cable detected, CBLID above VIH

0 = 40-conductor cable detected, CBLID below VIL

DB35 Series 7200.2 Product Manual, Rev. C

4.1.3

Set Features command

This command controls the implementation of various features that the drive supports. When the drive receives

this command, it sets BSY, checks the contents of the Features register, clears BSY and generates an inter-

rupt. If the value in the register does not represent a feature that the drive supports, the command is aborted.

Power-on default has the read look-ahead and write caching features enabled. The acceptable values for the

Features register are defined as follows:

Enable write cache (default).

Set transfer mode (based on value in Sector Count register).

Sector Count register values:

Set PIO mode to default (PIO mode 2).

Set PIO mode to default and disable IORDY (PIO mode 2).

PIO mode 0

PIO mode 1

PIO mode 2

PIO mode 3

PIO mode 4 (default)

Multiword DMA mode 0

Multiword DMA mode 1

Multiword DMA mode 2

Ultra DMA mode 0

Ultra DMA mode 1

Ultra DMA mode 2

Ultra DMA mode 3

Ultra DMA mode 4

Ultra DMA mode 5

Disable read look-ahead (read cache) feature.

Disable write cache.

Enable read look-ahead (read cache) feature (default).

Report full capacity available

Note. At power-on, or after a hardware or software reset, the default values of the features are as indi-

cated above.

DB35 Series 7200.2 Product Manual, Rev. C

4.1.4

S.M.A.R.T. commands

S.M.A.R.T. provides near-term failure prediction for disc drives. When S.M.A.R.T. is enabled, the drive moni-

tors predetermined drive attributes that are susceptible to degradation over time. If self-monitoring determines

that a failure is likely, S.M.A.R.T. makes a status report available to the host. Not all failures are predictable.

S.M.A.R.T. predictability is limited to the attributes the drive can monitor. For more information on S.M.A.R.T.

commands and implementation, see the Draft ATA-7 Standard.

SeaTools diagnostic software activates a built-in drive self-test (DST S.M.A.R.T. command for D4 ) that elimi-

nates unnecessary drive returns. The diagnostic software ships with all new drives and is also available at:

http://seatools.seagate.com.

This drive is shipped with S.M.A.R.T. features disabled. You must have a recent BIOS or software package that

supports S.M.A.R.T. to enable this feature. The table below shows the S.M.A.R.T. command codes that the

drive uses.

Codeinfeatures

S.M.A.R.T. command

S.M.A.R.T. Read Data

Vendor-specific

S.M.A.R.T. Enable/Disable Attribute Autosave

S.M.A.R.T. Save Attribute Values

S.M.A.R.T. Execute Off-line Immediate (runs DST)

S.M.A.R.T. Read Log Sector

S.M.A.R.T. Write Log Sector

Vendor-specific

S.M.A.R.T. Enable Operations

S.M.A.R.T. Disable Operations

S.M.A.R.T. Return Status

Note. If an appropriate code is not written to the Features Register, the command is aborted and 0x04

(abort) is written to the Error register.

DB35 Series 7200.2 Product Manual, Rev. C

5.0

Seagate Technology support services

Online services

Internet

www.seagate.com for information about Seagate products and services. Worldwide support is available 24

hours daily by e-mail for your questions.

Presales Support: www.seagate.com/support/email/email_presales.html or [email protected]

Technical Support: www.seagate.com/support/email/email_disc_support.html or [email protected]

mySeagate

my.seagate.com is the industry’s first Web portal designed specifically for OEMs and distributors. It provides

self-service access to critical applications, personalized content and the tools that allow our partners to man-

age their Seagate account functions. Submit pricing requests, orders and returns through a single, password-

protected Web interface—anytime, anywhere in the world.

spp.seagate.com

spp.seagate.com supports Seagate resellers with product information, program benefits and sales tools. You

may register for customized communications that are not available on the web. These communications contain

product launch, EOL, pricing, promotions and other channel-related information. To learn more about the ben-

efits or to register, go to spp.seagate.com, any time, from anywhere in the world.

Seagate Service Centers

Presales Support

Our Presales Support staff can help you determine which Seagate products are best suited for your specific

application or computer system, as well as product availability and compatibility.

Technical Support

Seagate technical support is available to assist you online at support.seagate.com or through one of our call

centers. Have your system configuration information and your “ST” model number available.

SeaTDD™ (+1-405-324-3655) is a telecommunications device for the deaf (TDD). You can send questions or

comments 24 hours daily and exchange messages with a technical support specialist during normal business

hours for the call center in your region.

Customer Service Operations

Warranty Service

Seagate offers worldwide customer support for Seagate drives. Seagate distributors, OEMs and other direct

customers should contact their Seagate Customer Service Operations (CSO) representative for warranty-

related issues. Resellers or end users of drive products should contact their place of purchase or one of the

Seagate CSO warranty centers for assistance. Have your drive’s “ST” model number and serial number avail-

able.

DB35 Series 7200.2 Product Manual, Rev. C

Data Recovery Services

Seagate offers data recovery services for all formats and all brands of storage media. Our Data Recovery Ser-

vices labs are currently located in North America. To speak with a case management representative, call

1-800-475-0143. Additional information, including an online request form and data loss prevention resources,

is available at www.datarecovery.seagate.com.

Authorized Service Centers

In some locations outside the US, you can contact an Authorized Service Center for service.

USA/Canada/Latin America support services

Seagate Service Centers

Presales Support

Call center

Americas

Toll-free

Direct dial

FAX

+1-405-324-4704

1-877-271-3285¹

+1-405-324-4730¹

Technical Support

Call center

Americas

Toll-free

Direct dial

FAX

+1-405-324-3339

1-800-SEAGATE²

+1-405-324-4700²

Customer Service Operations

Warranty Service

Call center

USA, Canada, Mexico and

Latin America

Toll-free

Direct dial

—

FAX / E-mail

+1-956-664-4725

1-800-468-3472³

Brazil

Jabil Industrial Do Brasil

—

+55-11-4191-4761

+55-11-4191-5084

[email protected]

LTDA⁴

Data Recovery Services

Call center

Toll-free

Direct dial

FAX

USA, Canada,

and Mexico

1-800-475-01435

+1-905-474-2162

1-800-475-0158

+1-905-474-2459

Hours of operation are 8:00 A.M. to 7:00 P.M., Monday through Friday (Central time).

Hours of operation are 8:00 A.M. to 8:00 P.M., Monday through Friday (Central time).

Hours of operation are 8:00 A.M. to 5:00 P.M., Monday through Friday (Central time).

Authorized Service Center

Hours of operation are 8:00 A.M. to 8:00 P.M., Monday through Friday, and 9:00 A.M. to 5:00 P.M., Saturday (Eastern time).

DB35 Series 7200.2 Product Manual, Rev. C

European support services

For presales and technical support in Europe, dial the Seagate Service Center toll-free number for your spe-

cific location. If your location is not listed here, dial our presales and technical support call center at +1-405-

324-4714 from 8:00 A.M. to 11:45 A.M. and 1:00 P.M. to 5:00 P.M. (Central Europe time) Monday through Friday.

The presales and technical support call center is located in Oklahoma City, USA.

For European warranty service, dial the toll-free number for your specific location. If your location is not listed

here, dial our European CSO warranty center at +31-20-316-7222 from 8:30 A.M. to 5:00 P.M. (Central Europe

time) Monday through Friday. The CSO warranty center is located in Amsterdam, The Netherlands.

Seagate Service Centers

Toll-free support numbers

Call center

Austria

Belgium

Denmark

France

Germany

Ireland

Italy

Presales and Technical Support

—

Warranty Service

00 800-47324289

00 800-311 12 38

00 800-47324289

00 800-31 92 91 40

00 800-47324289

00 800-47324283 (00 800-4SEAGATE)

00 800-47324283

00 800-311 12 38

00 800-47324283

00 800-31 92 91 40

00 800-47324283

Netherlands

Norway

Poland

Spain

Sweden

Switzerland

Turkey

United Kingdom

FAX services—All Europe (toll call)

Technical Support

Warranty Service

+1-405-324-3339

+31-20-653-3513

Africa/Middle East support services

For presales and technical support in Africa and the Middle East, dial our presales and technical support call

center at +1-405-324-4714 from 8:00 A.M. to 11:45 A.M. and 1:00 P.M. to 5:00 P.M. (Central Europe time) Mon-

day through Friday. The presales and technical support call center is located in Oklahoma City, USA.

For warranty service in Africa and the Middle East, dial our European CSO warranty center at +31-20-316-

7222 from 8:30 A.M. to 5:00 P.M. (Central Europe time) Monday through Friday, or send a FAX to +31-20-653-

3513. The CSO warranty center is located in Amsterdam, The Netherlands.

DB35 Series 7200.2 Product Manual, Rev. C

Asia/Pacific support services

For Asia/Pacific presales and technical support, dial the toll-free number for your specific location. The Asia/

Pacific toll-free numbers are available from 6:00 A.M. to 10:45 A.M. and 12:00 P.M. to 6:00 P.M. (Australian East-

ern time) Monday through Friday, except as noted. If your location is not listed here, direct dial one of our tech-

nical support locations.

Warranty service is available from 9:00 A.M. to 5:00 P.M., Monday through Friday. Warranty service for Australia

is available from 10:00 A.M. to 7:00 P.M., April through October, and from 11:00 A.M. to 8:00 P.M. November

through March (Australian Eastern time) Monday through Friday.

Seagate Service Centers

Call center

Australia

China (Mandarin)

Hong Kong

Toll-free

1800-14-7201

800-810-9668

800-90-0474

Direct dial

—

+86-10-6225-5336

FAX

—

1, 4

—

1, 4

Hong Kong (Cantonese)

001-800-0830-1730

1-800-180-1104

001-803-1-003-2165

0034 800 400 554

007 98 8521 7635

1-800-80-2335

0800-443988

800-1101-150

00-800-0830-1730

001-800-11-0032165

2, 4

India

Indonesia

3, 4

Japan

Korea

3, 4

—

Malaysia

New Zealand

Singapore

Taiwan (Mandarin)

Thailand

+65-6488-7525

—

1, 4

Customer Service Operations

Warranty Service

Call center

Asia/Pacific

Australia

Toll-free

—

1800-12-9277

—

Direct dial

+65-6485-3595

—

FAX

+65-6485-4860

—

India

+91-44-42015000

+91-44-42015184

Hours of operation are 8:30 A.M. to 5:30 P.M., Monday through Friday (Australian Western time).

Hours of operation are 9:00 A.M. to 6:00 P.M., Monday through Saturday.

Hours of operation are 9:30 A.M. to 6:30 P.M., Monday through Friday.

Authorized Service Center

DB35 Series 7200.2 Product Manual, Rev. C

Publication feedback survey

We are interested in your comments and suggestions regarding this publication. Please take a few minutes to

participate in our survey at the following URL:

http://surve y .seagate.com/survey/techpubs.nsf

Thank you for your time and comments.

DB35 Series 7200.2 Product Manual, Rev. C

Index

Data Defense 1

data-transfer rates 1

DC power 13

Default logical geometry 10

density 10

Device Configuration Freeze Lock 30

Device Configuration Identify 30

Device Configuration Restore 30

Device Configuration Set 30

Device Reset 30

Diagnostic Defense 1

diagnostic software 1, 37

DiscWizard 25

Disk Manager 25

dissipation 13

Download Microcode 30

Drive Defense 1

drive diagnostics 12

drive monitoring 1

Numerics

3D Defense System 1

acoustics 17

Active mode 15

agency certification (regulatory) 19

alternate capacity jumper 25

altitude 16

ambient conditions 3

ambient temperature 12, 16

areal density 1, 10

ATA interface 29

ATA-standard commands 30

Australian C-Tick 19

autodetection 1

average seek time 12

drive self-test 1, 37

DST 37

BIOS 25

BPI 10

electrical fast transient 18

electromagnetic compatibility 19

Electromagnetic Compatibility Directive 19

electromagnetic immunity 18

electrostatic discharge 18

EMC compliance 19

breather filter hole precautions 24

buffer 11

burst 1

cable 26

cable select 1

cable-select option 25

cache 1, 11

case temperature 16

CE mark 19

EN 60950 19

enclosures 20

Environmental protection 20

environmental specifications 16

EPRML 1, 10

error-correction algorithms 1

errors 18

European Union 19

European Union Restriction of Hazardous Substanc-

es 20

certification 19

Check Power Mode 30

chemical substances 20

commands 30

compliance 19

Execute Device Diagnostics 30

conducted noise 14

conducted RF immunity 18

configuring the drive 23

connector pins 29

connectors 26

contact start-stop cycles 18

Corrosive environment 21

CSA C22.2 (950) 19

CSEL 25

failure prediction 37

FCC verification 20

Features register 36

Flush Cache 30

Flush Cache Extended 30

Format Track 30

formatted capacity 10

frequency 18

C-Tick 19

current profile 14

cycles 18

Cylinders 10

DB35 Series 7200.2 Product Manual, Rev. C

geometry 10

noise 14

guaranteed sectors 10

nominal power 3

nonoperating shock 17

nonoperating vibration 17

nonrecoverable read errors 18

handling 23

heads 1, 10

height 12

humidity 16

operating 13

operating power and current 13

operating shock 16

operating vibration 17

orientation 26

I/O data-transfer rate 11

Identify Device 30

Identify Device command 33

Idle 13, 30

Idle and Standby timers 15

Idle Immediate 30

physical characteristics 12

pins 29

Idle mode 15

PIO 29

Idle mode power 13

IEC950 19

power consumption 13

power dissipation 13

power management 15

power specifications 13

power-management modes 15

Power-on to Ready 12

precautions 26

Information Technology Equipment 19

Initialize Device Parameters 30

interface 10, 29

interface signals 29

interference 20

internal data-transfer rate OD 11

ISO document 7779 17

preventive maintenance 18

programmable power management 15

jumper settings 25

radiated RF immunity 18

radio and television interference 20

radio frequency 18

random track location 13

Read Buffer 30

Korean RRL 19

Read DMA 30

Read DMA Extended 30

Read DMA without Retries 30

read errors 18

LBA mode 10

length 12

logical geometry 10

Read Log Ext 30

Read Multiple 1, 30

Read Multiple Extended 30

Read Native Max Address 30

Read Native Max Address Extended 30

Read Sectors 30

Read Sectors Extended 30

Read Sectors Without Retries 30

Read Verify Sectors 30

Read Verify Sectors Extended 30

Read Verify Sectors Without Retries 30

Read/write heads 10

maintenance 18

master 25

master/slave 1

Master/slave configuration 25

maximum temperature 16

measurement locations 16

modes 29

monitoring 1

mounting the drive 23, 26

Recalibrate 30

recording and interface technology 10

recording density 10

DB35 Series 7200.2 Product Manual, Rev. C

recording heads 1

recording method 10

relative humidity 16

reliability 18

resistance 14

resistive load 14

RF 18

Standby 13, 31

Standby Immediate 31

Standby mode 13, 15

Standby to Ready 12

start/stop times 12

start-stop cycles 18

static-discharge precautions 23

stop times 12

RoHS 20

subassembly 20

support services 39

surge immunity 18

S.M.A.R.T. commands 37

S.M.A.R.T. Disable Operations 31

S.M.A.R.T. drive monitoring 1

S.M.A.R.T. Enable Operations 31

S.M.A.R.T. Enable/Disable Autosave 31

S.M.A.R.T. Execute Offline 31

S.M.A.R.T. Read Attribute Thresholds 31

S.M.A.R.T. Read Data 31

S.M.A.R.T. Read Log Sector 31

S.M.A.R.T. Return Status 31

S.M.A.R.T. Save Attribute Values 31

S.M.A.R.T. Write Log sector 31

safety certification 19

screws 26

technical support services 39

temperature 16

temperature gradient 16

TGMR 1

timers 15

track density 10

track-to-track seek time 12

TUV North America 19

UL 1950 19

Ultra ATA/100 26

Ultra DMA 26

SeaTools 1, 37

sectors 10

Sectors per track 10

Security Disable Password 31

Security Erase Prepare 31

Security Erase Unit 31

Security Freeze 31

vibration 17

voltage 14

voltage dips, interrupts 18

voltage tolerance 14

Security Set Password 31

Security Unlock 31

Seek 31

seek mode 13

seek time 12

Seeking 13

servo electronics 13

Set Features 31

Set Features command 36

Set Max Address 31

Set Max Address Extended 31

Set Multiple Mode 31

shock 16

signals 29

single-track seeks 12

slave 25

weight 12

wet bulb temperature 16

width 12

Write Buffer 31

Write DMA 31

Write DMA Extended 31

Write DMA Without Retries 31

Write Log Extended 31

Write Multiple 1, 31

Write Multiple Extended 31

Write Sectors 31

Write Sectors Extended 32

Write Sectors Without Retries 32

Sleep 13, 31

Sleep mode 15

sound 17

specifications 3

spindle speed 11

Spinup 13

spinup power 13

DB35 Series 7200.2 Product Manual, Rev. C

Seagate Technology LLC

920 Disc Drive, Scotts Valley, California 95066-4544, USA

Publication Number: 100389999, Rev. C, Printed in U.S.A.

Siemens IGWIPS200 1 User Manual
Seagate MOMENTUS ST9320325AS User Manual
Seagate BARRACUDA ES SERIAL ATA ST3400820NS User Manual
SanDisk SDUFD2AB 0256 User Manual
SanDisk SDUFD2AB 0064 User Manual
Samsung SGH X820 User Manual
Philips XP AJ 3380 User Manual
Philips VOIP433IB User Manual
Olympus CAMEDIA MAUSB 1 User Manual
Nokia COMMUNICATOR 9210i User Manual