Oricom WNS1
Jumbo Display
Alarm Clock and Shaker
User Guide
Keep this user guide for future reference
LOCATION OF CONTROLS
PM
AL
1
2
3
1 – PM LED indicator
2 – Alarm LED indicator
3 – Strobe light and snooze button
9
8
1
2
7
3
6
4
5
1 – Alarm mode switch
2 – Alarm and ring volume
3 – Set alarm
6 – Alarm off
7 – Alarm tone
8 – Alarm + ring / Off / Ring function switch
9 – Shaker Lo / Hi switch
4 – Set clock
5 – Set hours & minutes
- 3 -
INITIAL SETUP
PACK CONTENTS
Unpack the unit and check to be sure you have all the items below.
·
1 Jumbo display /alarm clock (WNS1)
·
·
·
·
·
1 modular line Cord
1 Double adaptor plug
1 Shaker
1 Warranty Card
This User guide
Battery Door
4
1
AC Adaptor
Double Adaptor
Phone Wall
socket
3
Shaker
Dimmer switch
2
INITIAL SET UP
-
Connect one end of the phone line cord to the back of the unit (1) and the other end to the
double adaptor plug.
- Plug the double adaptor into the telephone wall socket.
- Connect the AC adaptor to the socket (4) on the back of the unit.
-
-
Plug the AC adaptor to the power socket on the wall.
Plug in the shaker to the back of the unit.
- 4 -
ALARM AND CLOCK FUNCTION
SETTING THE TIME (
)
-
-
-
-
Press and hold
(set clock) button.
Press H (hour) and M (minute) until correct hour and minutes appear on the display.
Release (set clock) button.
For p.m. hours, the p.m. indicator will appear on the display near the inscription PM.
SETTING THE ALARM TIME (
)
-
-
-
-
Press and hold
(set alarm) button.
Press H (hour) or M (minute) until correct hour and minutes appear on the display.
Release
Press
(set alarm) button.
H and M to reset the alarm clock to 12.
SETTING THE ALARM MODE
Put the function switch on A+T position. Choose which alarm mode you wish to be awakened to by
moving the alarm mode switch to one of the following selections:
V
:
only shaker activated
V+S :
F+V :
both sound and shaker alarm activated
both strobe light and shaker alarm activated
When the alarm is set to one of the alarm modes, the alarm indicator will appear on the display near
the inscription AL.
The table below shows how the alarm modes indicate an incoming call from the alarm clock.
ALARM MODE
SOUND
ACTION
Buzzer
ALARM CLOCK
Continuous
INCOMING CALL
With pauses
SHAKER
STROBE LIGHT
Vibrates
Flashes
Continuous
Continuous
With pauses
With pauses
SNOOZE BUTTON
/ STROBE LIGHT
When the alarm sounds, you can use the
snooze button to temporarily turn off the alarm. The
alarm will come on again after 9 minutes. This sequence can be carried out for up to 2 hours after
which the alarm mode will be automatically switched off.
SWITCHING THE ALARM OFF
Press the alarm off button (OFF), the alarm will them operate at the same time the next day. The
alarm if not switched off will continue to sound for up to 2 hours and then be automatically switched
off.
- 5 -
RINGER ON/OFF SWITCH (A+T / OFF / T)
-
-
-
A+T (alarm + telephone): for the alarm and telephone ring position.
OFF: alarm and ring off.
T (telephone): for the telephone ring position.
HOW TO USE WITH YOUR TELEPHONE
-
-
-
Ensure that your telephone is connected to the WNS1 as shown in the installation section.
Select the ringer On/Off switch on the A+T or T position for the ring.
Choose which of the alarm modes you wish to alert you of your incoming telephone calls (see
page 5: V, V+S, S+F or F+V)
-
When the alarm mode selected indicates there is an incoming telephone call, lift the telephone
handset and answer the call. When you have finished the call replace the handset and the
alarm will be ready to indicate the next call.
DIMMER SWITCH (
)
Adjust the brightness of the display by moving the
control at the rear of your WNS1.
VOLUME CONTROL
Use this to set the volume of the ringer and the alarm sound.
TONE
This allows you to select the tone of the alarm sound that is best for you.
SHAKER SWITCH (
- / + )
Sets the motion of the shaker to Lo (-) or Hi (+)
- 6 -
CARE & WARRANTY
CLEANING
The surface of the case can be cleaned with a dry, soft, lint-free cloth. Never use cleaning agents,
particularly aggressive solvents. Apart from occasional cleaning of the case, no other care is
necessary. The rubber feet on the base are not resistant to all cleaning agents. The rubber feet do
not normally leave any marks on the surface. However, on account of the multitude of varnishes and
surface finishes used, surface marks caused by the feet of the unit cannot be ruled out.
This product is covered by a 12 month warranty against defective workmanship or parts. The warranty
does not extend to damage caused by misuse, negligence, water ingress, excessive voltage,
telephone line faults or lightning. This guarantee in no way affects your statutory rights. Full details of
the warranty are contained in the enclosed warranty card.
WARRANTY
If you feel this product is not working correctly please consult the user guide and ensure that you are
using the product in accordance with the instructions. Remove all extra telephone equipment and
connect only this telephone directly to the telephone socket.
If the fault is still present, connect another telephone (if available) to the telephone socket. The
results will show you whether the fault lies with this unit or with the telephone line.
If the product is working correctly the fault is on the telephone line. Please contact your network
operator for assistance.
To order replacement batteries and in case of any technical issues you may have with this
product please consult our website for further information or send us an email for a prompt
response to your enquiry.
In the unlikely event of a fault developing, please contact us for assistance. If the product is then
found to be faulty you will be asked to return it directly to us with a copy of the purchase receipt.
Australia
Oricom International Pty Ltd
Locked Bag 658
South Windsor, NSW 2756
Customer support
Email: [email protected]
Fax: (02) 4574 8898
Ph: 1300 889 785
- 7 -
|