Compact Disc Player
C-7000R
Instruction Manual
En
Precautions
1. Recording Copyright—Unless it’s for personal use
only, recording copyrighted material is illegal without
the permission of the copyright holder.
2. AC Fuse—The AC fuse inside the unit is not user-
serviceable. If you cannot turn on the unit, contact
your Onkyo dealer.
3. Care—Occasionally you should dust the unit all over
with a soft cloth. For stubborn stains, use a soft cloth
dampened with a weak solution of mild detergent and
water. Dry the unit immediately afterwards with a
clean cloth. Don’t use abrasive cloths, thinners,
alcohol, or other chemical solvents, because they may
damage the finish or remove the panel lettering.
4. Power
7. Never Touch this Unit with Wet Hands—Never
handle this unit or its power cord while your hands are
wet or damp. If water or any other liquid gets inside
this unit, have it checked by your Onkyo dealer.
8. Handling Notes
10. Moisture Condensation
Moisture condensation may damage this unit.
Read the following carefully:
Moisture may condense on the lens of the optical
pickup, one of the most important parts inside this
unit.
• Moisture condensation can occur in the following
situations:
– The unit is moved from a cold place to a warm
place.
• If you need to transport this unit, use the original
packaging to pack it how it was when you originally
bought it.
• Do not leave rubber or plastic items on this unit for
a long time, because they may leave marks on the
case.
• This unit’s top and rear panels may get warm after
prolonged use. This is normal.
• If you do not use this unit for a long time, it may not
work properly the next time you turn it on, so be
sure to use it occasionally.
– A heater is turned on, or cold air from an air
conditioner is hitting the unit.
– In the summer, when this unit is moved from an
air conditioned room to a hot and humid place.
– The unit is used in a humid place.
• Do not use this unit when there’s the possibility of
moisture condensation occurring. Doing so may
damage your discs and certain parts inside this unit.
If condensation does occur, unplug the power cord
and leave the unit for two to three hours in the room
temperature.
WARNING
BEFORE PLUGGING IN THE UNIT FOR THE
FIRST TIME, READ THE FOLLOWING SECTION
CAREFULLY.
AC outlet voltages vary from country to country.
Make sure that the voltage in your area meets the
voltage requirements printed on the unit’s rear panel
(e.g., AC 230 V, 50 Hz or AC 120 V, 60 Hz).
• When you’ve finished using this unit, remove all
discs and turn off the power.
9. Installing this Unit
• Install this unit in a well-ventilated location.
• Ensure that there’s adequate ventilation all around
this unit, especially if it’s installed in an audio rack.
If the ventilation is inadequate, the unit may
overheat, leading to malfunction.
• Do not expose this unit to direct sunlight or heat
sources, because its internal temperature may rise,
shortening the life of the optical pickup.
• Avoid damp and dusty places, and places subject to
vibrations from loudspeakers. Never put the unit on
top of, or directly above a loudspeaker.
• Install this unit horizontally. Never use it on its side
or on a sloping surface, because it may cause a
malfunction.
The power cord plug is used to disconnect this unit
from the AC power source. Make sure that the plug is
readily operable (easily accessible) at all times.
Some models have a voltage selector switch for
compatibility with power systems around the world.
Before you plug in such a model, make sure that the
voltage selector is set to the correct voltage for your
area.
Pressing the [POWER] button to select OFF mode
does not fully disconnect from the mains. If you do
not intend to use the unit for an extended period,
remove the power cord from the AC outlet.
• If you install this unit near a TV, radio, or VCR, the
picture and sound quality may be affected. If this
occurs, move this unit away from the TV, radio, or
VCR.
5. Preventing Hearing Loss
Caution
Excessive sound pressure from earphones and
headphones can cause hearing loss.
6. Batteries and Heat Exposure
Warning
Batteries (battery pack or batteries installed) shall not
be exposed to excessive heat as sunshine, fire or the
like.
En
3
This unit contains a semiconductor laser system and is
classified as a “CLASS 1 LASER PRODUCT”. So, to use
this model properly, read this Instruction Manual
carefully. In case of any trouble, please contact the store
where you purchased the unit.
is encouraged to try to correct the interference by one or
more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and
receiver.
For British models
Replacement and mounting of an AC plug on the power
supply cord of this unit should be performed only by
qualified service personnel.
To prevent being exposed to the laser beam, do not try to
open the enclosure.
• Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV
technician for help.
IMPORTANT
The wires in the mains lead are coloured in accordance
with the following code:
Blue: Neutral
Brown: Live
As the colours of the wires in the mains lead of this
apparatus may not correspond with the coloured markings
identifying the terminals in your plug, proceed as follows:
The wire which is coloured blue must be connected to the
terminal which is marked with the letter N or coloured
black.
CAUTION:
CLASS 1M VISIBLE AND INVISIBLE LASER
RADIATION WHEN OPEN. DO NOT VIEW
DIRECTLY WITH OPTICAL INSTRUMENTS.
THIS PRODUCT UTILIZES A LASER. USE OF
CONTROLS OR ADJUSTMENTS OR
PERFORMANCE OF PROCEDURES OTHER THAN
THOSE SPECIFIED HEREIN MAY RESULT IN
HAZARDOUS RADIATION EXPOSURE.
For Canadian Models
NOTE:
THIS CLASS B DIGITAL APPARATUS COMPLIES
WITH CANADIAN ICES-003.
For models having a power cord with a polarized plug:
CAUTION:
TO PREVENT ELECTRIC SHOCK, MATCH WIDE
BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.
The wire which is coloured brown must be connected to
the terminal which is marked with the letter L or coloured
red.
The label on the right is applied
on the rear panel.
Modèle pour les Canadien
REMARQUE:
IMPORTANT
1. This unit is a CLASS 1 LASER PRODUCT and
employs a laser inside the cabinet.
2. To prevent the laser from being exposed, do not
remove the cover. Refer servicing to qualified
personnel.
The plug is fitted with an appropriate fuse. If the fuse
needs to be replaced, the replacement fuse must approved
by ASTA or BSI to BS1362 and have the same ampere
rating as that indicated on the plug. Check for the ASTA
mark or the BSI mark on the body of the fuse.
If the power cord’s plug is not suitable for your socket
outlets, cut it off and fit a suitable plug. Fit a suitable fuse
in the plug.
CET APPAREIL NUMÉRIQUE DE LA CLASSE B EST
CONFORME À LA NORME NMB-003 DU CANADA.
Sur les modèles dont la fiche est polarisée:
ATTENTION:
POUR ÉVITER LES CHOCS ÉLECTRIQUES,
INTRODUIRE LA LAME LA PLUS LARGE DE LA
FICHE DANS LA BORNE CORRESPONDANTE DE
LA PRISE ET POUSSER JUSQU’AU FOND.
For U.S. models
FCC Information for User
CAUTION:
The user changes or modifications not expressly approved
by the party responsible for compliance could void the
user’s authority to operate the equipment.
For European Models
Declaration of Conformity
NOTE:
We,
ONKYO EUROPE
This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation.
This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However, there is
no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful
interference to radio or television reception, which can be
determined by turning the equipment off and on, the user
ELECTRONICS GmbH
LIEGNITZERSTRASSE 6,
82194 GROEBENZELL,
GERMANY
declare in own responsibility, that the ONKYO product
described in this instruction manual is in compliance with the
corresponding
technical standards such as EN60065,
EN55013, EN55020 and EN61000-3-2, -3-3.
GROEBENZELL, GERMANY
K. MIYAGI
ONKYO EUROPE ELECTRONICS GmbH
En
4
Features
• Plays Audio CD, CD-R, CD-RW, MP3 CD, and WMA
*
CD
• New circuit technology for Buffer Circuitry
• Separate Digital/Analog Circuitry
• Separate Massive Transformers for Digital and Analog
Circuitry (Toroidal Transformer for Analog Circuitry)
• Thermally Regulated High-Precision Clock
• Silent Disc Mechanism with Solid Die-Cast Aluminum
Tray
• Separate Anti-Vibration Aluminum Panels for Top,
Front, and Sides
• New Circuit Board Construction to Reduce Vibration
• PLL Ultra Low Jitter Technology
• Separate TI (Burr-Brown) 192 kHz/24-Bit DACs
(PCM1792) for L/R Channels
• Pure Analog Mode
• Transport Mode for Digital Output
• AES/EBU Balanced Digital Output with XLR
Connector
• 3 Digital Outputs (Optical, Coaxial and AES/EBU)
• Gold-Plated, Machined Solid Brass, Wide Pitch Audio
Outputs
• Display Dimmer (Normal/Dim/Off)
*
Discs should be properly finalized.
En
5
Technologies
New circuit technology
Thermally Regulated Super-Precision Clock
Since the advent of digital audio, signal-to-noise ratios
have improved dramatically. However, the S/N ratio
reflects static noise only, and takes no account of another
type of noise that occurs as the byproduct of sound
reproduction—dynamic noise. To reduce this type of
noise, Onkyo has developed New circuit technology for
use in our hi-fi components. Despite being beyond the
normal range of human hearing, frequencies above
100 kHz are susceptible to clock pulse and other forms of
distortion from digital devices. Such distortion in the
super-high-frequency range can generate “beat
The C-7000R boasts an extremely precise clocking
mechanism that controls and coordinates the timing of all
digital signal processes—rather like how a conductor
directs and coordinates the individual instruments of an
orchestra. The C-7000R uses a state-of-the-art crystal
oscillator that achieves a frequency deviation of 1.5 ppm
at room temperature-much lower than with a conventional
oscillator. Even in surrounding temperatures of -30°C or
+80°C the frequency remains stable, with only 0.5 ppm
of additional frequency deviation.
interference”, which in turn affects the character or
atmosphere of the original sound. By improving linearity
and reducing distortion in the super-high-frequency range,
Onkyo’s new New circuit technology effectively reduces
perceptible noise. New circuit technology is incorporated
into the buffer circuitry of the C-7000R CD player.
PLL (Phase Locked Loop) Ultra-Low Jitter Technology
Jitter is an unwanted side-effect of the digital-to-analog
conversion process caused by fluctuations in the time
domain of a digital signal. PLL ultra-low jitter technology
reduces jitter by comparing the input and output phases of
the digital signal and creating an accurate clock waveform.
This enhances the precision of digital signal processing
and noticeably improves perceived audio quality.
Separate Digital/Analog Circuitry and Transformers
To prevent unwanted interference, the C-7000R employs
physically separate circuitry for digital and analog
processing. In the same vein, the player also features
separate transformers for digital and analog circuitry.
New Circuit Board Construction
Rather than being directly connected to the chassis base,
the circuit boards inside the C-7000R are cushioned by
internal struts and affixed to the front, side, and rear
panels. This method of construction prevents vibrations
from the chassis from adversely affecting the circuit
boards.
En
6
Supplied Accessories
Make sure you have the following accessories:
Remote controller and two batteries
Audio connection cable
Remote controller (RC-796C). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (1)
Batteries (R03/AAA). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (2)
Audio connection cable (0.8 m/2.6 ft) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (1)
*
In catalogs and on packaging, the letter at the end of the product name indicates the color.
Specifications and operations are the same regardless of color.
Power cord
Power cord (1.8 m/5.9 ft) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (1)
(Plug type varies from country to country.)
Thank you for purchasing an Onkyo Compact Disc Player. Please read this
manual thoroughly before making connections and plugging in the unit.
Following the instructions in this manual will enable you to obtain optimum
performance and listening enjoyment from your new Compact Disc Player.
Please retain this manual for future reference.
En
8
Contents
Introduction
Important Safety Instructions .................................................................................2
Precautions...............................................................................................................3
Features ....................................................................................................................5
Technologies............................................................................................................6
Block Diagram..........................................................................................................7
Supplied Accessories..............................................................................................8
Before Using the Compact Disc Player................................................................10
Installing the Batteries .......................................................................................10
Using the Remote Controller .............................................................................10
Installing the Compact Disc Player....................................................................10
Getting to Know the Compact Disc Player ..........................................................11
Front Panel ........................................................................................................11
Display...............................................................................................................12
Rear Panel.........................................................................................................13
Remote Controller..............................................................................................14
Disc Note ...........................................................................................................15
Connections
Connections ...........................................................................................................17
Cable and Jacks ................................................................................................17
Connecting the Power Cord...............................................................................18
Turning On & Basic Operations
Basic Operations....................................................................................................21
Turning On/Off the Compact Disc Player ..........................................................21
Playing the Disc.................................................................................................22
Selecting Files (MP3/WMA)...............................................................................23
Setting the Display Brightness...........................................................................24
Advanced Operations
Advanced Operations............................................................................................25
Repeat Playback................................................................................................25
Memory Playback (CD)......................................................................................26
Memory Playback (MP3/WMA)..........................................................................27
Random Playback..............................................................................................29
Selecting a Folder (Search Mode).....................................................................29
Displaying Disc Information ...............................................................................30
Custom Setup
Custom Setup.........................................................................................................31
Setup Procedures..............................................................................................31
Preferences .......................................................................................................31
Setting the Analog/Digital Output.......................................................................32
Others
Troubleshooting.....................................................................................................33
Specifications.........................................................................................................35
En
9
Before Using the Compact Disc Player
Installing the Batteries
Using the Remote Controller
Installing the Compact Disc Player
To use the remote controller, point it at the compact disc
player’s remote control sensor, as shown below.
To open the battery compartment, press the small
hollow and slide the cover.
1
Remote control sensor
Compact disc player
20 cm (8")
10 cm (4")
30° off center
(Left/Right)
10 cm (4")
Approx. 16 ft. (5 m)
Insert the two supplied batteries (R03/AAA) in
accordance with the polarity diagram inside the
battery compartment.
2
Note
10 cm (4")
• The remote controller may not work reliably if the compact disc
player is subjected to bright light, such as direct sunlight or
inverter-type fluorescent lights. Keep this in mind when
installing.
• If another remote controller of the same type is used in the same
room, or the compact disc player is installed close to equipment
that uses infrared rays, the remote controller may not work
reliably.
Install the compact disc player on a sturdy rack or shelf.
Position it so that its weight is evenly dispersed on its four
legs. Do not install the compact disc player in a place with
vibration or an unstable location.
Replace the cover and slide it shut.
• Don’t put anything, such as a book, on the remote controller,
because the buttons may be pressed inadvertently, thereby
draining the batteries.
3
• The remote controller may not work reliably if the compact disc
player is installed in a rack behind colored glass doors. Keep this
in mind when installing.
• The remote controller will not work if there’s an obstacle
between it and the compact disc player’s remote control sensor.
Note
• If the remote controller doesn’t work reliably, try replacing the
batteries.
• Don’t mix new and old batteries or different types of batteries.
• If you intend not to use the remote controller for a long time,
remove the batteries to prevent damage from leakage or
corrosion.
• Remove expired batteries as soon as possible to prevent damage
from leakage or corrosion.
En
10
Getting to Know the Compact Disc Player
Front Panel
a
b
c d
e
f
g h
i j
k
l
m n
The page numbers in parentheses show where you can find the main explanation for each item.
a ON/STANDBY button (➔ 21)
Use this button to set the compact disc player to On or
Standby.
f 0 button (➔ 22)
k POWER switch (➔ 21)
Opens and closes the disc tray.
This is the main power switch. When set to the OFF
position (@), the compact disc player is completely
shutdown. It must be set to the ON position (^) to set
the compact disc player to On or Standby.
b Standby LED (➔ 21)
Lights when the compact disc player is in Standby
mode.
Use this button to pause disc playback. When paused,
this resumes playback.
l Display Off LED (➔ 24)
h 2 button (➔ 22)
Lights when the display is turned off.
Before entering standby mode with the ASb function,
the Display Off LED flashes 30 seconds before the
ASb function starts running.
c Remote control sensor (➔ 10)
The sensor receives control signals from the remote
controller.
Use this button to stop disc playback.
i 1 button (➔ 22)
Use this button to play the disc.
d Display (➔ 12)
j OUTPUT MODE button (➔ 32)
Use this button to switch the audio output signal
between analog and digital (or both).
m 7 button (➔ 22)
See “Display”.
Use this button to skip to the beginning of the track
being played. Press and hold down to fast reverse.
e Disc tray (➔ 22)
Insert discs into this tray.
n 6 button (➔ 22)
Use this button to skip to the beginning of the next
track. Press and hold down to fast forward.
En
11
Display
a b
c
e
f
g h i
j
k l
m
For detailed information, see the pages in parentheses.
a 1 indicator (➔ 22)
f TOTAL indicator (➔ 21)
k MP3 indicator (➔ 21)
Lights during playback.
Lights when the total and remaining time of the track
are shown.
Lights together with the folder name, file number or
file name which contains MP3 tracks.
b 3 indicator (➔ 22)
g REMAIN indicator (➔ 30)
l WMA indicator (➔ 21)
Lights when playback is paused.
Lights when the remaining time of the track is shown.
Lights together with the folder name, file number or
file name which contains WMA tracks.
c MEMORY indicator (➔ 26, 27, 28)
Lights during memory playback.
m Message area
Lights during random playback.
d FOLDER indicator (➔ 23)
Displays various information.
Lights together with the folder name.
Lights during repeat playback. “1” is shown when
only the currently playing track is repeated.
e TRACK indicator (➔ 22)
Lights together with the track number or file name.
j Audio output indicators
Indicate the type of audio output (➔ 32): DIGITAL
and/or ANALOG.
En
12
Rear Panel
e
a
b c
d
a AUDIO OUTPUT ANALOG L/R jacks
d AUDIO OUTPUT DIGITAL OPTICAL jack
This optical digital audio output is for connecting
components with optical digital audio inputs, such as
preamplifier.
Connect the analog audio in jack of an amplifier or
similar to this jack, using the supplied audio cable.
b AUDIO OUTPUT DIGITAL AES/EBU jack
This balanced AES/EBU output is for connecting a
component with a balanced AES/EBU input.
e AC INLET
The supplied power cord is connected here. The other
end of the power cord should be connected to a
suitable wall outlet.
c AUDIO OUTPUT DIGITAL COAXIAL jack
This coaxial digital audio output is for connecting
components with coaxial digital audio inputs, such as
preamplifier.
See “Connections” for connection information
(➔ 17 to 19).
En
13
Remote Controller
You can also use the remote controller to control your Onkyo C-7000R.
For detailed information, see the pages in parentheses.
a
j
k
a 8 button (➔ 21)
f !/"/#/$ and ENTER buttons
Sets the compact disc player to On or Standby.
Used to select and adjust settings.
b
c
b DIMMER button (➔ 24)
g SEARCH button (➔ 29)
Search for a folder on a disc containing MP3 or WMA
tracks.
Adjusts the display brightness.
c DISPLAY button (➔ 30)
h SETUP button
Displays information about the current input source.
Used to change settings.
d RANDOM button (➔ 29)
i Number buttons (➔ 24)
Used with the random playback.
d
e
l
Used to select tracks and the like.
e Playback mode buttons (➔ 22)
j 0 button (➔ 22)
3 button
Open and close the disc tray.
Used to pause playback. When paused, this resumes
playback.
k OUTPUT MODE button (➔ 32)
Use this button to switch the audio output signal
between analog and digital (or both).
7 button
Used to skip to the beginning of the track being
played.
l REPEAT button (➔ 25)
Used with the repeat playback.
f
1 button
Used to play the disc.
m MEMORY button (➔ 26, 27, 28)
Used to begin or end memory playback.
6 button
Used to skip to the beginning of the next track.
n CLEAR button
Used to clear any numbers that have been entered
during numeric input. When making a memory
setting, the selected track is erased.
5 button
Used to fast reverse the current song.
2 button
g
h
Used to stop disc playback.
4 button
m
n
Used to fast forward the current song.
i
En
14
Disc Note
Supported Discs
CD playback with copy-control function
Precautions for Inkjet Printable Discs
The compact disc player supports the following discs.
Some audio CDs with copy-control function do not
comply with official CD standards. These are special discs
and cannot be played with this compact disc player.
Do not leave a CD-R/CD-RW having a label printed with
an inkjet printer in the compact disc player for a long time.
The disc could get stuck in the compact disc player, or
could damage the compact disc player.
Audio CD
PCM
Remove the disc from the compact disc player when not
being played, and store it in a case. A freshly printed disc
will stick easily, and should not be played immediately.
Handling Discs
CD-R
Audio CD, MP3,
WMA
Hold discs by the edge, or by the center hold and edge.
Avoid touching the playback surface (surface with nothing
printed on it).
CD-RW
Audio CD, MP3,
WMA
Caring for Discs
Label surface
(printed surface)
If the disc is dirty, the compact disc player will have a hard
time reading signals, and the audio quality may drop. If
the disc is dirty, gently wipe off fingerprints and dust with
a soft cloth. Lightly wipe from the center outwards.
To remove stubborn dust or dirt, wipe the
disc with a soft cloth dampened with
water, and then dry it with a dry cloth. Do
not use cleaning spray for analog records
or antistatic agents, etc.
• Do not use discs designed for purposes other than audio,
such as CD-ROMs for PC use. Abnormal noise could
damage the speakers or compact disc player.
• The compact disc player supports CD-R and CD-RW
discs. Note that some discs may not playback because of
the CD characteristics, scratches, contamination or the
recording state. A CD recorded with an audio CD record
will not playback unless it is finalized.
Playback
surface
Do not attach paper or stickers, or write on the playback or
label surface of the disc. Take care not to scratch or
damage the disc.
• Never use discs which have a special shape (such as
hearts or octagons). These types of discs could jam and
damage the compact disc player.
Never use volatile chemicals such as benzine or paint
thinner as they can impregnate the disc surface.
Precautions for Rental Discs
About the Condensation
Do not use discs with residue from cellophane tape, rental
discs with labels which are peeling off, or discs with
decorative labels. This type of disc could get stuck in the
compact disc player, or could damage the compact disc
player.
Moving the compact disc player from a cold room into a
warm room, or heating a cold room with a heater may
cause waterdrops to form inside the compact disc player.
This is called condensation. Not only does this cause
malfunction, but it can also damage the compact disc
player or any inserted disc. Remove discs from the
compact disc player when not in use.
If condensation appears, unplug the power cord and leave
the compact disc player more than 3 hours at room
temperature.
En
15
Playback of MP3 and WMA CDs
Playback of WMA CDs
®
MP3 and WMA files recorded on a CD-R/CD-RW can be
played with this compact disc player.
• WMA stands for “Windows Media Audio”, an audio
compression technology developed by Microsoft
Corporation USA.
• Use discs which have been recorded following the
ISO9660 Level 2 file system. (The supported directory
depth is eight levels, the same as ISO9660 Level 1)
Discs recorded with the hierarchical file system (HFS)
cannot be played.
• Only WMA files with the extension “.WMA” or “.wma”
are supported.
• Encode the WMA file with an application approved by
Microsoft Corporation USA. The file may not playback
correct if encoded with an unapproved application.
• Variable bitrates (VBR) between 32 kbps and 192 kbps
(32/44.1/48 kHz) are supported.
• Always close the disc tray.
Note
• Copyright-protected WMA files cannot be played back.
• WMA Pro, Lossless and Voice are not supported.
• A disc recorded with a recorder or personal computer may not
play in some cases. (Cause: Disc’s characteristics, damaged or
dirty disc, dirt on player’s lens, dew condensation, etc.)
• A disc recorded on a personal computer may not play because of
the application settings or environment. Record the disc with the
proper format. (Contact the application maker for details.)
• A disc with insufficient storage capacity may not play back
properly.
*
Windows Media is a registered trademark or trademark of
Microsoft Corporation in the United States and/or in other
countries.
Playback of MP3 CDs
• Only MP3 files with the extension “.MP3” or “. mp3”
are supported.
• This compact disc player supports files recorded in
MPEG 1 Audio Layer 3 (32-320 kbps), with the
sampling frequency of 32/44.1/48 kHz.
• Variable bitrates (VBR) between 32 kbps and 320 kbps
are supported. The time information during VBR
playback may not display correctly.
En
16
Connections
Connections
Cable and Jacks
Balanced AES/EBU
This is a professional digital audio interface. Balanced AES/EBU cables are used for better noise immunity and longer cable runs. The maximum
sampling rate for PCM output is 44.1 kHz/16 bit, 2ch.
Optical digital audio
Optical digital connections allow you to enjoy digital sound. The maximum sampling rate for PCM input is 44.1 kHz/16 bit, 2ch.
OPTICAL
Coaxial digital audio
Analog audio (RCA)
Coaxial digital connections allow you to enjoy digital sound. The maximum sampling rate for PCM input is 44.1 kHz/16 bit, 2ch.
Analog audio connections (RCA) carry analog audio.
Orange
L
White
Red
R
Note
• Push plugs in all the way to make good connections (loose connections can cause noise or malfunctions).
Right!
Wrong!
• To prevent interference, keep audio cables away from power cords and speaker cables.
• The compact disc player’s optical digital jack has a shutter-type cover that opens when an optical plug is inserted and closes when it’s removed. Push plugs in all the way.
• To prevent shutter damage, hold the optical plug straight when inserting and removing.
• The analog audio cable can be used instead of the coaxial cable.
About Balanced Output (AES/EBU Jack)
Plugging the AES/EBU cable
Unplugging the AES/EBU cable
Match the pins and insert the jack until you hear a “click.” Make sure that the jack is locked
by lightly pulling the connection cable.
Pull out the connection cable while holding down the button.
Push
1
2
Push
En
17
Connecting the Power Cord
AC INLET
Compact Disc Player C-7000R
Supplied power cord
To an AC wall outlet
(Plug type varies from
country to country.)
Make sure that the main power of the compact disc
player is turned off.
1
Note
• Never disconnect the power cord from the compact disc
player while the other end is still plugged into a wall outlet.
Doing so may cause an electric shock. Always disconnect the
power cord from the wall outlet first, and then the compact disc
player.
Connect all of your components.
2
3
Connect the supplied power cord to the compact
disc player’s AC INLET.
• Turning on the compact disc player may cause a momentary
power surge that might interfere with other electrical equipment
on the same circuit. If this is a problem, plug the compact disc
player into a different branch circuit.
Plug the power cord into an AC wall outlet.
4
• Do not use a power cord other than the one supplied with the
compact disc player. The supplied power cord is designed
exclusively for use with the compact disc player and should not
be used with any other equipment.
Tip
• To reduce noise, do not tie the signal cable and power cable
together. Wire them so that they are away from each other.
En
18
Connecting a Preamplifier or Integrated Amplifier
Analog Connection
Digital (Optical or Coaxial) Connection
Preamplifier P-3000R
Preamplifier P-3000R
L
R
Connect either of them.
Compact Disc Player C-7000R
Compact Disc Player C-7000R
This is an example of digital connection using the preamplifier P-3000R.
Connect either of them.
This is an example of analog connection using the preamplifier P-3000R.
En
19
Digital (AES/EBU) Connection
Preamplifier P-3000R
Compact Disc Player C-7000R
This is an example of AES/EBU connection using the preamplifier P-3000R.
En
20
Turning On
&
Basic Operations
Basic Operations
Turning On/Off the Compact Disc Player
Turning On the Compact Disc Player
Turning Off the Compact Disc Player
ON/STANDBY
Set POWER to the ON position (^) on the front
Press 8 to turn on the compact disc player.
The compact disc player comes on, the display lights,
and the Standby LED goes off.
Press 8 to set the compact disc player to Standby.
The compact disc player will enter Standby mode, and
the Standby LED lights.
1
2
1
2
panel.
You can also use compact disc player’s
ON/STANDBY.
POWER
To completely shut down the compact disc player,
You can also use compact disc player’s
ON/STANDBY.
set POWER to the OFF position (@).
8
(Audio CD Display)
Note
• See “Custom Setup” for the auto standby function (➔ 32).
Total number
Total
of tracks
playing time
(MP3/WMA Display)
Total number
of folders
Total number
of tracks
Tip
• After a certain period of warning up, the temperature of the
compact disc player’s components and internal temperature are
stabilized, and the sound will soften.
Note
• If the message “NO DISC” appears on the display, no disc
information is available.
• The compact disc player remembers the state when power was
previously turned OFF, and returns to the state.
En
21
Playing the Disc
■ To Select Tracks
Place the disc on the tray with the label-side facing
up.
0
3
2
1
2
Press 6 to select the next track/file or 7 to select
the previous track/file.
• If you press 7 during playback or while
playback is paused, the beginning of the current
track/file is selected.
• If you select a track/file while playback is stopped,
press 1 to start playback.
• When 7/6 are pressed, the following Disc
information is displayed for MP3/WMA.
(During playback) File number/File name → File
name → File number/playing time
(Paused) File number/File name → File name →
Folder number/File number
7 6
0
■ To Fast-Forward or Fast-Reverse
When you want to listening to the 8 cm disc, place it
in the center of the tray.
During playback or while playback is paused, hold
down 4 to fast-forward or 5 to fast-reverse.
Press 1 to start playback.
3
The disc tray closes and playback starts.
■ To Pause Playback
3, 7, 1,
6, 5, 2,
4
During playback, press 3. The 3 indicator lights.
(Audio CD Display)
To resume playback, press 1 or 3 again.
1 indicator
3 indicator
Press 0 to open the disc tray.
1
Pressing 0 while the compact disc player is on
Standby will turn on the compact disc player and open
the disc tray.
Track currently
playing
Elapsed track
time
■ To Stop Playback
(MP3/WMA Display)
Press 2 to stop playback.
File name will be displayed by scrolling.
■ To Eject the Disc
Press 0 to open the disc tray.
Tip
Note
• Only alphanumeric characters in MP3/WMA CD information
are displayed correctly. Double-byte characters and other
characters appear as underscores.
• For MP3/WMA CDs, you can select MP3/WMA files in other
folders.
• If a disc has been set in the tray, when the power of the compact
disc player is turned on, then it starts to play automatically.
En
22
Selecting Files in Navigation Mode
Selecting Files (MP3/WMA)
For MP3/WMA CDs, files (MP3/WMA files) may be
organized in a hierarchically, with folders containing files
and subfolders, as shown below.
2
1
Press " or ENTER (front panel: 1).
The first folder name in ROOT appears on the display.
If the disc contains no folders, the first file name
appears.
2
Root
File #1
Folder #1
Folder #2
File #10
Folder #3
File #11
File #12
File #13
Use #/$ or 7/6 to select other folders and
files at the same level. To move up a level, press !
or 3 (front panel: 2).
3
4
7 6
Folder #4
File #14
Folders that don’t contain files or subfolders can’t be
selected.
3, 7, 1, 6, 2
Press ENTER or " to move down a level (front
panel: 1).
Use #/$ or 7/6 to select a file in the folder.
5
6
!, ", #, $
File #18
Press ENTER or 1.
ENTER
Playback will start with the specified file or folder and
continue until all of the files on the disc have been
played.
In this manual, MP3/WMA files are referred to as files.
Likewise, folders (directories) are referred to as folders.
To cancel the procedure at any point, press 2 on the
In Navigation mode, you can select files by navigating
through the folder hierarchy. This mode can only be used
while playback is stopped.
remote controller.
For the compact disc player, there are two modes for
selecting files (MP3/WMA files): Navigation mode and
All Folder mode.
In Navigation mode, you can select files (MP3/WMA
files) by navigating through the folder hierarchy, moving
in and out of folders and subfolders.
Note
• The behavior of 2 on the compact disc player can be set from
While playback is stopped, press " or 2.
1
“STOP KEY” (➔ 32).
The compact disc player enters Navigation mode and
“[ROOT]” appears on the display.
In All Folder mode, all folders appear at the same level,
making it easy to select folders regardless of the hierarchy.
Note
• If you don’t select a specific MP3/WMA file or folder for
playback, all of the MP3/WMA files on the disc will be played
in numerical order starting with file #1 in parentheses.
En
23
Selecting Files in All Folder Mode
Setting the Display Brightness
2
1
Press " (front panel: 1).
3
4
The first file name inside the folder appears.
Use #/$ or 7/6 to select the files within the
DIMMER
folder.
To select another folder, press 3 again (front panel:
2), and then use 7/6 to select it.
7 6
Press ENTER or 1 to start playback.
Playback will start with the specified file or folder and
continue until all of the file on the disc have been
played.
You can adjust the brightness of the compact disc player’s
display.
3, 7, 1,
6, 2
To cancel the procedure at any point, press 2.
Press DIMMER repeatedly to change the brightness
of the display in sequence.
1
!, ", #, $,
ENTER
■ To Select Folders and Files by Number
1. Use the number buttons as shown in the examples
below to enter folder/file numbers.
Normal → Dim → Off
Normal
To select:
Press:
Folder/File #8
Folder/File #10
Folder/File #34
In All Folder mode, you don’t have to navigate the folder
hierarchy because all folders that contain files appear at
the same level. This mode can only be used while
playback is stopped.
Dim
Used to enter numbers over 10.
2. Playback starts. When you enter folder number,
playback will start from the first file in the selected
folder. If a folder contains more than 99 files, single-
and double-digit file numbers must be preceded by
zeros. For example, to specify file #8, press 8. To
specify file #34, press >10, 3, and 4. To specify file
#134, press >10, 1, 3, and 4.
While playback is stopped, press ! or 3 (front
1
panel: press and hold 2).
Off
The compact disc player enters All Folder mode, and
“1-” appears on the display.
The Display Off LED lights.
Note
• The behavior of 2 on the compact disc player can be set from
Use #/$ or 7/6 to select the other folders.
2
Note
“STOP KEY” (➔ 32).
You can select any folder that contains files.
• The display lights for a 5 seconds if you control any buttons on
the front panel or remote controller when the display brightness
is set to OFF.
En
24
Advanced Operations
Advanced Operations
Repeat Playback
Press REPEAT repeatedly to select Repeat All,
Repeat 1 or Repeat Off.
1
The “̃” or “̃ 1” indicator lights.
Repeat All → Repeat 1 → Repeat Off
Repeat All
̃ indicator
REPEAT
Repeat 1
̃ 1 indicator
In repeat playback, you can play an entire disc repeatedly,
play one track repeatedly, or combine it with memory
playback to play the playlist repeatedly, or random
playback to play all of the tracks on the disc in random
order repeatedly.
Repeat Off
Repeat-1 playback can’t be combined with memory
playback, random playback.
To cancel repeat playback, press REPEAT
repeatedly until the “RPT OFF” appears.
2
The “̃” or “̃ 1” indicator goes off.
Tip
• Repeat playback is cancelled when you press 0 to open the disc
tray.
• Repeat playback is cancelled when you press 8 or
ON/STANDBY to turn off the compact disc player.
En
25
Memory Playback (CD)
■ To Change the Display
Press MEMORY.
The MEMORY indicator lights.
1
2
While the memory setting operations, press DISPLAY
repeatedly to change the display information as follows:
Track number/Playlist number → Track number/Playing
time → Track number/Total playing time
0
MEMORY indicator
DISPLAY
■ To Select Other Tracks During Memory
Playback
Use 7/6 to select the first track you want to
Use 7/6 to select other tracks during memory
add to the playlist, and then press 1 or ENTER.
7, 1, 6,
playback.
5, 4
■ To Check the Playlist
While playback is stopped, use 5/4 to scroll
through the playlist. Track number and play time are
displayed.
ENTER
Track number Playlist number
Repeat this step to add additional tracks to the playlist.
You can alternatively use the number buttons to select
tracks.
■ To Remove Tracks from the Playlist
• While memory playback is stopped, press CLEAR.
Each press removes the last track from the playlist.
• The playlist is deleted on changing the playback mode
(press MEMORY after stopping the playback).
Press ENTER or 1.
3
MEMORY
CLEAR
The memory playback starts.
■ To Cancel Memory Playback
Track currently playing
• Stop the playback, then press MEMORY to change the
playback mode. The MEMORY indicator goes off, and
memory playback is cancelled.
In memory playback, you can create a playlist of up to 25
tracks. Memory playback can be set only when the
playback is stopped.
• Memory playback is also cancelled by pressing 0 to
open the disc tray, 8 or ON/STANDBY to turn off the
compact disc player.
Note
• If the total playing time is more than 99 minutes and 59 seconds,
“--:--” appears.
• You can add up to 25 tracks to the playlist. If you try to add more,
the message “MEM-FULL” appears.
En
26
Memory Playback (MP3/WMA)
Memory Playback in Navigation Mode
■ To Change the Display
Press MEMORY.
The MEMORY indicator lights.
2
1
1
2
While the memory setting operations, press DISPLAY to
change the display information as follows:
File name → Folder name → Folder number/File number
Press " or 2.
The compact disc player enters Navigation mode and
“[ROOT]” appears on the display.
Note
• See “Selecting Files (MP3/WMA)” for the Navigation Mode
information (➔ 23).
• The behavior of 2 on the compact disc player can be set from
“STOP KEY” (➔ 32).
• Memory playback is cancelled when you press 0 to open the
7 6
Press " or ENTER (front panel: 1).
disc tray.
3
4
The first folder name in ROOT appears on the display.
• Memory playback is cancelled when you press 8 or
ON/STANDBY to turn off the compact disc player.
Use #/$ or 7/6 to select other folders and
files at the same level.
DISPLAY
Folders that don’t contain files or subfolders can’t be
selected.
Press ENTER or " to move down a level (front
5
panel: 1).
3, 7, 1,
Use #/$ or 7/6 to select a file in the folder.
6
7
6, 2
Press 1.
The first file is memorized in the playlist.
!, ", #, $
Use #/$ or 7/6 to continue selecting the
8
9
memory file.
ENTER
To move up a level, press ! or 3 (front panel: 2).
To continue selecting the memory file, repeat steps 4
to 7.
To memorize other files of the same folder in the
MEMORY
playlist, use 7/6 to select files, then press 1.
In memory playback, you can create a playlist of up to 25
files. Memory playback can be set only when the playback
is stopped.
Press ENTER or 1.
Memory playback starts.
En
27
Memory Playback in All Folder Mode
2
1
Press " (front panel: 1).
4
5
7
Use #/$ or 7/6 to select the files.
Press 3 (front panel: 2), then repeat steps 3 to 6.
To memorize other files of the same folder in the
playlist, repeat steps 5 to 6.
7 6
Press ENTER (front panel: 1).
8
Memory playback starts.
3, 7, 1,
Note
6, 2
• See “Selecting Files (MP3/WMA)” for the All Folder Mode
information (➔ 24).
• The behavior of 2 on the compact disc player can be set from
!, ", #, $
“STOP KEY” (➔ 32).
• Memory playback is cancelled when you press 0 to open the
disc tray.
ENTER
• Memory playback is cancelled when you press 8 or
ON/STANDBY to turn off the compact disc player.
MEMORY
Press MEMORY.
The MEMORY indicator lights.
1
2
Press ! or 3 (front panel: press and hold 2).
The compact disc player enters All Folder mode and
“1-” appears on the display.
MEMORY indicator
Use #/$ or 7/6 to select the folders.
3
En
28
Random Playback
Selecting a Folder (Search Mode)
Tip
7, 6
• Random playback is cancelled when you press 0 to open the
disc tray.
• Random playback is cancelled when you press 8 or
ON/STANDBY to turn off the compact disc player.
ENTER
RANDOM
1
SEARCH
In random playback, all of the files on the disc are played
in random order. This mode can only be used while
playback is stopped.
This section explains how to select MP3/WMA folders
during Playback.
During playback, press SEARCH.
The compact disc player enters All Folder mode and
folders are displayed.
1
While playback is stopped, press RANDOM.
The RANDOM indicator lights.
1
To select the previous folder, press 7. To select
2
the next folder, press 6.
You can also use the number buttons to select the
folder.
RANDOM indicator
Press 1.
2
Press ENTER or 1.
3
The random playback starts.
Playback will start from the first file in the selected
folder.
To cancel random playback, stop the playback,
3
then press RANDOM to change the playback mode.
The RANDOM indicator goes off, and random
playback is cancelled.
Note
• SEARCH cannot be used during Random Playback and
Memory Playback (➔ 26, 29).
• See “Selecting Files in All Folder Mode” to select folder by
number(➔ 24).
If you press RANDOM during playback, the message
“NOR PLY” (Normal play) is displayed.
En
29
During playback or pause
Displaying Disc Information
(Audio CD Display)
Folder name:
Name of the current folder.
Elapsed file time:
The length of time that the current file has been playing
(default display).
DISPLAY
Title name:
Title of the current file (if ID3 tag present). When there
is no ID3 tag, the message “TITLE-NO DATA”
appears.
Remaining file time:
The amount of time remaining for the current file
(REMAIN indicator appears).
REMAIN indicator
Press DISPLAY repeatedly to show the following
disc information.
Artist name:
Name of the Artist (if ID3 tag present).
1
Remaining disc time:
The amount of time remaining for the entire disc
(TOTAL and REMAIN indicators appear).
While playback is stopped
(Audio CD Display)
Album name:
Name of the album (if ID3 tag present).
Track and total playing time appears on the display.
(MP3/WMA Display)
Total number
You can display various information about the MP3/WMA
file currently playing, including ID3 tags such as title
name, artist name, and album name.
Total playing time
of tracks
Sampling rate and bit rate:
Sampling rate and bit rate of the current file.
(MP3/WMA Display)
The name of disc appears on the display.
Elapsed file time:
The length of time that the current file has been playing
(default display).
Note
• To display the disc name, press DISPLAY while playback is
stopped.
File name:
Name of the current file.
• If a file or folder name contains any characters that cannot be
displayed, an underscore will appears in place of those
characters. Alternatively, you can set the compact disc player so
that names containing such characters are displayed as “FILE n”
or “FOLDER n”, “n” being the file or folder number. See “BAD-
NAME” for undisplayable characters setting (➔ 31).
En
30
Custom Setup
Custom Setup
Setup Procedures
Preferences
AUDIO
This preference determines whether or not the file name
scrolls across the display when an MP3/WMA file is
selected.
In Navigation mode, the file name scrolls across the
display regardless of this setting (➔ 23).
7, 1, 6
■ FILTER
`SHARP (default)
This preference allows the band property up to
20 kHz to be output almost flat.
`SLOW
■ FOLDER
`SCROLL (default)
`NOT
This preference determines whether or not the folder
name scrolls across the display when an MP3/WMA
folder is selected.
#, $
This preference brings higher reproducibility of
input waveform, and is suitable to reproduce
agogics, or subtle attack of sound signals, along with
sound image localization for each musical
instrument.
ENTER
In Navigation mode, the folder name scrolls across the
display regardless of this setting (➔ 23).
This preference configures the setting to switch the
characteristics of the digital filter for D/A conversion.
You can opt for whichever of the characteristics that
vary depending on your switching.
SETUP
■ HIDE-NUM
`DISABLE (default)
Displays numbers.
`ENABLE
Press SETUP.
1
2
■ PHASE
`NORMAL (default)
The waveform recorded in disc will be output with
its polarity left intact.
`REVERSE
Use #/$ or 7/6 to select the preference you
Hides numbers.
want to change.
This preference determines whether or not the numbers
at the beginning of file and folder names are hidden.
When you create an MP3/WMA CD on a personal
computer, you cannot normally determine the playback
order of the files. However, if you number the
MP3/WMA files in order, starting with 01, 02, 03, and
so on, they will play in that order.
The waveform recorded in disc will be output with
its reversed polarity.
This preference configures the setting to switch the
phase of the analog audio output.
You may give it a try to switch and listen so that an
optimum sound quality can be obtained from the
amplifier and the speakers on line.
The preferences are explained in the next column.
Press ENTER or 1.
3
4
■ BAD-NAME
`NOT (default)
`REPLACE
Use #/$ or 7/6 to select the preference’s
options.
DISPLAY
This preference determines whether or not file and
folder names that contain undisplayable characters are
replaced with “FILE n.” or “FOLDER n.”, “n” being the
file or folder number. When set to “NOT”, displayable
characters are displayed and underscores are used in
place of any undisplayable characters. For ID3 tags,
underscores are used in place of undisplayable
characters regardless of this preference.
Press ENTER or 1.
5
■ DISC
`DISPLAY (default)
`NOT
This preference determines whether or not the disc
name is displayed when an MP3/WMA CD is read.
When the preference has been set, “FINISH” appears
on the display.
To cancel the procedure at any point, press SETUP.
■ FILE
`SCROLL (default)
`NOT
En
31
■ STOP-KEY
`NAVI (default)
`FOLDER
EXTRA
Setting the Analog/Digital Output
■ ID3-VER1
`READ (default)
`DISABLE
OUTPUT MODE
This preference determines how 2 on the compact disc
`NO READ
player works.
This preference determines whether or not version
1.0/1.1 tags are read and displayed. When set to “NO
READ”, version 1.0/1.1 ID3 tags will not be displayed.
When the “NAVI” (Navigation) option is selected,
pressing 2 once selects Navigation mode.
When the “FOLDER” (ALL Folder) option is selected,
pressing 2 once selects All Folder mode.
When the “DISABLE” option is selected, compact disc
player does not enter Navigation or All Folder mode by
pressing 2.
■ ID3-VER2
`READ (default)
`NO READ
This preference determines whether or not version
2.2/2.3/2.4 tags are read and displayed. When set to
“NO READ”, version 2.2/2.3/2.4 ID3 tags will not be
displayed.
Note
Switch the output between DIGITAL/ANALOG,
DIGITAL, ANALOG in order.
• This setting has no effect on the remote controller.
ASb (Auto Standby)
■ CD-EXTRA
`AUDIO (default)
`MP3
This preference applies to CD Extra discs and
determines whether music in the audio session or
MP3/WMA files in the data session are played.
Press OUTPUT MODE repeatedly on the front
panel.
The selected Audio output indicator lights.
1
■ ASb (Auto Standby)
`ON
`OFF
For compact disc player playback, it is activated when
the playback is stopped for 30 minutes; however, it is
not activated when the playback is paused continuously.
Default setting: ON (European models), OFF (North
American models)
Audio output indicator
■ JOLIET
`USE SVD (default)
`ISO9660
This preference applies to MP3/WMA CDs in Joliet
format and determines whether the compact disc player
reads the SVD data or treats the disc as an ISO 9660
disc. Normally, this preference doesn’t need to be
changed. SVD (Supplementary Volume Descriptor)
supports long file and folder names and characters other
than letters and numbers.
`DIGITAL/ANALOG (default):
Uses both outputs.
`DIGITAL:
Note
Uses the digital output only.
Turn the analog output off to perform more
stable playback.
• Before entering standby mode with the ASb function, the
Display Off LED flashes 30 seconds before the ASb function
starts running.
`ANALOG:
Uses the analog output only.
Turn the digital output off to reduce the effect of
digital noise during playback.
INITIAL
■ INITIAL
`CANCEL
`EXECUTE
This preference resets the compact disc player to
factory default.
En
32
Others
Troubleshooting
Power
Audio
Can’t turn on the Compact Disc Player.
There’s no sound.
Audio output is intermittent when the
Compact Disc Player is subjected to
vibration.
• Make sure that the power cord is properly plugged into
the wall outlet (➔ 18).
• Unplug the power cord from the wall outlet, wait 5
seconds or more, then plug it in again.
• Check all connections and correct as necessary (➔ 17).
signals.
• The compact disc player is equipped with a feature to
switch the digital/analog output. Check if the connection
between the compact disc player and a connected
component is appropriate, and also whether the selection
of the selector is correct.
• The compact disc player is not a portable device. Use it
in a location that’s not subject to shock or vibration.
The Compact Disc Player turns off
unexpectedly.
Audio performance
• Audio performance will be at its best about 10 to 30
minutes after the compact disc player has been turned on
and had time to warm up.
• When the set ASb starts running, the compact disc
player will automatically go Standby (➔ 32).
The sound quality is not good.
• Using cable ties to bundle audio cables with speaker or
power cables may degrade the sound quality. So don’t
do it.
• Make sure all audio connecting plugs are pushed in all
the way (➔ 17).
• The sound quality can be affected by strong magnetic
fields, such as that from a TV. Try moving any such
devices away from the compact disc player.
• If you have any devices that emit high-intensity radio
waves near the compact disc player, such as a cellular
phone that’s being used to make a call, the compact disc
player may output noise.
• The compact disc player’s precision drive mechanism
may emit a faint hissing sound while reading discs
during playback or when searching for tracks. You may
be able to hear this noise in extremely quiet
environments.
En
33
Disc Playback
External Components
Remote Controller
Can’t play a disc.
No sound is heard from a connected
component.
The remote controller doesn’t work
properly.
• The disc is upside down. Load the disc with the label-
side facing up (➔ 15, 22).
• The disc is dirty. Remove the disc and clean it (➔ 15).
• If condensation appears, unplug the power cord and
leave the compact disc player more than 3 hours at room
temperature.
• Make sure the audio cable is connected correctly
(➔ 17).
• Make sure that all audio connecting plugs are pushed in
all the way (➔ 17).
• Make sure that the connected component’s input jack
and the input settings are correct.
• Make sure that the connected component’s volume isn’t
set to the lowest level, and that the volume isn’t muted.
• Make sure the batteries have been installed with the
correct polarity (+/–) (➔ 10).
• Replace both batteries with new ones. (Do not mix
different types of batteries or new and old batteries.)
• The remote controller is too far away from the compact
disc player, or there’s an obstacle between them (➔ 10).
• The compact disc player’s remote control sensor is being
subjected to bright light (inverter-type fluorescent light
or sunlight).
• CD-R/CD-RW that are not finalized cannot be played.
Disc playback skips.
• The compact disc player is located behind the glass
doors of a audio rack or cabinet.
• Install the compact disc player somewhere free of
vibration.
• The disc is very scratched. Replace the disc.
Onkyo is not responsible for damages (such as CD
rental fees) due to unsuccessful recordings caused by
the unit’s malfunction. Before you record important
data, make sure that the material will be recorded
correctly.
playback.
• No such track on the disc. Enter another number (➔ 24).
The compact disc player contains a microcomputer
for signal processing and control functions. In very
rare situations, severe interference, noise from an
external source, or static electricity may cause it to
lockup. In the unlikely event that this should happen,
unplug the power cord, wait at least 5 seconds, and
then plug it again.
tracks.
• The disc is dirty. Remove the disc and clean it (➔ 15).
• The disc is very scratched. Replace the disc.
Before disconnecting the power cord from the wall
outlet, set the main power switch to OFF.
Can not play tracks in the disc’s playback
order.
• Turn off any special playback modes (e.g. repeat,
memory, or random).
En
34
Specifications
C-7000R
Frequency Response
2 Hz - 20 kHz
Signal to Noise Ratio
116 dB
Audio Dynamic Range
THD (Total Harmonic Distortion)
100 dB
0.0015 %
Audio Output/Impedance
Optical
–22.5 dBm
0.5 Vp-p / 75 Ω
3.3 Vp-p / 110 Ω
Coaxial
AES/EBU
Rated RCA Output Level and Impedance
Digital Outputs
2.0 V (rms) / 330 Ω
Optical: 1
Coaxial: 1
Analog Stereo Outputs
Balance Output
L, R
AES/EBU (DIGITAL)
Power Supply
(North American) AC 120 V, 60 Hz
(European) AC 230 V, 50 Hz
Power Consumption
Standby Power Consumption
Dimensions (W × H × D)
Weight
(North American) 21 W
(European) 18 W
(North American) 0.2 W
(European) 0.3 W
435 W × 99 H × 315.2 D mm
(17-1/8 W × 3-7/8 H × 12-7/16 D inches)
12 kg (26.5 lbs)
Operation Condition Temperature/Humidity 5 ºC - 35 ºC/15% - 85%
Playable Discs Audio CD, CD-R, CD-RW, MP3, WMA (CD-R, CD-RW)
*
Discs that have not been properly finalized may only be
partially playable or not playable at all.
Specifications and features are subject to change without notice.
En
35
2-1, Nisshin-cho, Neyagawa-shi, OSAKA 572-8540, JAPAN
Tel: 072-831-8023 Fax: 072-831-8163
ONKYO U.S.A. CORPORATION
18 Park Way, Upper Saddle River, N.J. 07458, U.S.A.
ONKYO EUROPE ELECTRONICS GmbH
Liegnitzerstrasse 6, 82194 Groebenzell, GERMANY
ONKYO EUROPE ELECTRONICS GmbH (UK BRANCH)
The Coach House 81A High Street, Marlow, Buckinghamshire, SL7 1AB, UK
Tel: +44-(0)1628-473-350 Fax: +44-(0)1628-401-700
ONKYO CHINA LIMITED
Unit 1 & 12, 9/F, Ever Gain Plaza Tower 1, 88, Container Port Road, Kwai Chung, N.T., Hong Kong.
Tel: 852-2429-3118 Fax: 852-2428-9039
Y1011-1
SN 29400529
(C) Copyright 2010 ONKYO CORPORATION Japan. All rights reserved.
* 2 9 4 0 0 5 2 9 *
|
