Nokia 5300 Xpress Music
User Guide
9254409
Issue 1
1
Nokia operates a policy of continuous development. Nokia reserves the right to make
changes and improvements to any of the products described in this document without prior
notice.
This device complies with Directive 2002/95/EC on the restriction of the use of certain
hazardous substances in electrical and electronic equipment.
Under no circumstances shall Nokia be responsible for any loss of data or income or any
special, incidental, consequential or indirect damages howsoever caused.
The contents of this document are provided "as is". Except as required by applicable law, no
warranties of any kind, either express or implied, including, but not limited to, the implied
warranties of merchantability and fitness for a particular purpose, are made in relation to the
accuracy, reliability or contents of this document. Nokia reserves the right to revise this
document or withdraw it at any time without prior notice.
The availability of particular products may vary by region. Please check with the Nokia dealer
nearest to you.
EXPORT CONTROLS
This device may contain commodities, technology or software subject to export laws and
regulations from the US and other countries. Diversion contrary to law is prohibited.
FCC/INDUSTRY CANADA NOTICE
Your device may cause TV or radio interference (for example, when using a telephone in close
proximity to receiving equipment). The FCC or Industry Canada can require you to stop using
your telephone if such interference cannot be eliminated. If you require assistance, contact
your local service facility. This device complies with part 15 of the FCC rules. Operation is
subject to the following two conditions: (1) This device may not cause harmful interference,
and (2) this device must accept any interference received, including interference that may
cause undesired operation. Any changes or modifications not expressly approved by Nokia
could void the user's authority to operate this equipment.
3
Contents
Memory full.......................................... 30
Folders.................................................... 30
Voice messages.................................... 31
Info messages ...................................... 31
Service commands.............................. 31
Delete messages.................................. 31
SIM messages....................................... 32
Message settings................................. 32
For your safety.......................... 6
1. General information............. 9
Access codes............................................ 9
Configuration settings service ........ 10
Download content.............................. 10
Digital rights management.............. 10
2. Get started......................... 12
Install SIM card and battery............ 12
Charge the battery.............................. 13
Memory card installation ................. 13
Open the slide phone......................... 14
Switch the phone on and off........... 14
Antenna ................................................. 15
Headset.................................................. 15
Phone strap........................................... 16
7. Phonebook.......................... 34
Search for a contact .......................... 34
Save names and phone numbers.... 34
Save details........................................... 34
Copy or move contacts...................... 34
Edit contact details............................ 35
Synchronize all .................................... 35
Delete contacts.................................... 35
Business cards...................................... 35
Settings.................................................. 36
Groups.................................................... 36
1-touch dials........................................ 36
Info, service, and my numbers ........ 36
3. Your phone......................... 17
Keys and parts...................................... 17
Standby mode...................................... 18
Indicators and icons........................... 19
Flight mode........................................... 20
Keypad lock (keyguard) ..................... 20
Functions without a SIM card......... 21
8. Log ...................................... 38
9. Settings ............................. 39
Profiles................................................... 39
Themes................................................... 39
Tones....................................................... 39
Display.................................................... 40
Time and date ...................................... 40
My shortcuts ........................................ 41
Connectivity ......................................... 42
Call.......................................................... 46
Phone...................................................... 47
Enhancements ..................................... 47
Configuration....................................... 48
Security.................................................. 49
Restore factory settings.................... 49
4. Call functions..................... 22
Make a call ........................................... 22
1-touch dialing.................................... 22
Enhanced voice dialing...................... 22
Answer or decline a call.................... 23
Options during a call.......................... 23
5. Navigate the menus .......... 25
6. Messaging .......................... 26
Text messages...................................... 26
Picture message .................................. 28
Postcards............................................... 29
Nokia Xpress audio messaging........ 30
4
Phone software updates.................... 50 Contacts................................................. 67
Conversation options.......................... 67
10.Operator menu.................. 51
Set your availability............................ 67
Log off service...................................... 68
11.Gallery............................... 52
Print images.......................................... 52
16.SIM services....................... 69
Memory card......................................... 52
17.t-zones............................... 70
12.Media ................................ 54
Set up browsing................................... 70
Camera and video................................ 54
Connect to a service........................... 70
Media player......................................... 55
Browse pages........................................ 71
Music player.......................................... 55
Bookmarks............................................. 71
Radio....................................................... 57
Appearance settings........................... 72
Voice recorder....................................... 58
Security settings.................................. 72
Equalizer................................................. 59
Download settings .............................. 73
Stereo widening................................... 59
t-zones inbox........................................ 73
Cache memory...................................... 74
Browser security.................................. 74
13.Organizer........................... 60
Alarm clock............................................ 60
Calendar................................................. 60
To-do list................................................ 61
18.PC connectivity................. 76
Nokia PC Suite...................................... 76
Notes....................................................... 61
Packet data, HSCSD, and CSD.......... 76
Calculator .............................................. 61
Bluetooth............................................... 76
Countdown timer ................................ 62
Data communication applications . 76
Stopwatch ............................................. 62
19.Enhancements................... 78
14.Games and Applications .. 63
Launch a game..................................... 63 20.Battery information.......... 79
Launch an application........................ 63 Charging and discharging................. 79
Application options............................. 63 Nokia battery authentication .......... 80
Download an application.................. 64
Care and maintenance ........... 82
15.Instant messaging ............ 65
Register with an IM service.............. 65
Login........................................................ 65
Begin an IM session............................ 66
Receive and reply to messages........ 66
Return to chat session....................... 66
Additional safety
information............................. 83
Index........................................ 88
5
F o r y o u r s a f e t y
For your safety
Read these simple guidelines. Not following them may be dangerous or illegal.
Read the complete user guide for further information.
SWITCH ON SAFELY
Do not switch the phone on when wireless phone use is prohibited or
when it may cause interference or danger.
ROAD SAFETY COMES FIRST
Obey all local laws. Always keep your hands free to operate the vehicle
while driving. Your first consideration while driving should be road safety.
INTERFERENCE
All wireless phones may be susceptible to interference, which could
affect performance.
SWITCH OFF IN HOSPITALS
Follow any restrictions. Switch the phone off near medical
equipment.
SWITCH OFF IN AIRCRAFT
Follow any restrictions. Wireless devices can cause interference in
aircraft.
SWITCH OFF WHEN REFUELING
Do not use the phone at a refueling point. Do not use near fuel or
chemicals.
SWITCH OFF NEAR BLASTING
Follow any restrictions. Do not use the phone where blasting is in
progress.
USE SENSIBLY
Use only in the normal position as explained in the product
documentation. Do not touch the antenna unnecessarily.
QUALIFIED SERVICE
Only qualified personnel may install or repair this product.
ENHANCEMENTS AND BATTERIES
Use only approved enhancements and batteries. Do not connect
incompatible products.
6
F o r y o u r s a f e t y
WATER-RESISTANCE
Your phone is not water-resistant. Keep it dry.
BACK-UP COPIES
Remember to make back-up copies or keep a written record of all
important information stored in your phone.
CONNECTING TO OTHER DEVICES
When connecting to any other device, read its user guide for detailed
safety instructions. Do not connect incompatible products.
EMERGENCY CALLS
Ensure the phone is switched on and in service. Press the end key as
many times as needed to clear the display and return to the start
screen. Enter the emergency number, then press the call key. Give
your location. Do not end the call until given permission to do so.
■ About your device
The wireless device described in this guide is approved for use on the GSM 850,
1800, and 1900 networks. Contact your service provider for more information
about networks.
When using the features in this device, obey all laws and respect the privacy and
legitimate rights of others.
When taking and using images or video clips, obey all laws and respect local
customs as well as privacy and legitimate rights of others, including copyrights.
Warning: To use any features in this device, other than the alarm clock,
the device must be switched on. Do not switch the device on when
wireless phone use may cause interference or danger.
■ Network services
To use the phone you must have service from a wireless service provider. Many of
the features in this device depend on features in the wireless network to
function. These network services may not be available on all networks or you may
have to make specific arrangements with your service provider before you can
utilize network services. Your service provider may need to give you additional
instructions for their use and explain what charges will apply. Some networks
may have limitations that affect how you can use network services. For instance,
some networks may not support all language-dependent characters and services.
Your service provider may have requested that certain features be disabled or not
activated in your device. If so, they will not appear on your device menu. Your
7
F o r y o u r s a f e t y
device may also have been specially configured for your network provider. This
configuration may include changes in menu names, menu order and icons.
Contact your service provider for more information.
This device supports WAP 2.0 protocols (HTTP and SSL) that run on TCP/IP
protocols. Some features of this device, such as multimedia messaging (MMS),
browsing, instant messaging, remote synchronization, and content downloading
using the browser or MMS, require network support for these technologies.
■ Shared memory
The following features in this device may share memory: gallery, contacts, text
messages, multimedia messages, and instant messages, e-mail, calendar, to-do
notes, JavaTM games and applications, and note application. Use of one or more of
these features may reduce the memory available for the remaining features
sharing memory. For example, saving many Java applications may use all of the
available memory. Your device may display a message that the memory is full
when you try to use a shared memory feature. In this case, delete some of the
information or entries stored in the shared memory features before continuing.
Some of the features, such as text messages, may have a certain amount of
memory specially allotted to them in addition to the memory shared with other
features.
8
G e n e r a l i n f o r m a t i o n
1. General information
Congratulations on your purchase of this Nokia mobile phone. Some of its other
features include a calendar, a clock, an alarm clock, a radio, a music player, and a
built-in camera.
■ Access codes
Security code
The security code (5 to 10 digits) helps to protect your phone against
unauthorized use. The preset code is 12345. To change the code, and to set the
phone to request the code, see “Security,” p. 49.
PIN codes
The personal identification number (PIN) code and the universal personal
identification number (UPIN) code (4 to 8 digits) help to protect your SIM card
against unauthorized use. See “Security,” p. 49.
The PIN2 code (4 to 8 digits) may be supplied with the SIM card and is required
for some functions.
The module PIN is required to access the information in the security module. See
“Security module,” p. 74.
The signing PIN is required for the digital signature. See “Digital signature,” p. 75.
PUK codes
The personal unblocking key (PUK) code and the universal personal unblocking
key (UPUK) code (8 digits) is required to change a blocked PIN code and UPIN
code, respectively. The PUK2 code (8 digits) is required to change a blocked PIN2
code. If the codes are not supplied with the SIM card, contact your local service
provider for the codes.
Restriction password
The restriction password (4 digits) is required when using the Call restrictions.
See “Security,” p. 49.
9
G e n e r a l i n f o r m a t i o n
■ Configuration settings service
To use some of the network services, such as mobile Internet services, MMS,
Nokia Xpress audio messaging, or remote Internet server synchronization, your
phone needs the correct configuration settings. For more information on
availability, contact your network operator, service provider, nearest authorized
Nokia dealer, or visit the support area on the Nokia Web site,
When you have received the settings as a configuration message, and the
settings are not automatically saved and activated, Configuration settings
received is displayed.
To save the settings, select Show > Save. If required, enter the PIN code supplied
by the service provider.
To discard the received settings, select Exit or Show > Discard.
■ Download content
You may be able to download new content, such as themes, tones, and video
clips, to the phone (network service dependency). You may also be able to
download updates of phone software (network service dependency). See “Phone,”
p. 47, Phone updates.
For the availability of different services, pricing, and fees, contact your service
provider.
Important: Use only services that you trust and that offer adequate
security and protection against harmful software.
■ Digital rights management
Content owners may use different types of digital rights management (DRM)
technologies to protect their intellectual property, including copyrights. This
device uses various types of DRM software to access DRM-protected content.
With this device you may be able to access content protected with WMDRM 10,
OMA DRM 1.0, OMA DRM 1.0 forward lock, and OMA DRM 2.0. If certain DRM
software fails to protect the content, content owners may ask that such DRM
software's ability to access new DRM-protected content be revoked. Revocation
may also prevent renewal of such DRM-protected content already in your device.
Revocation of such DRM software does not affect the use of content protected
with other types of DRM or the use of non-DRM-protected content.
10
G e n e r a l i n f o r m a t i o n
Digital rights management (DRM) protected content comes with an associated
activation key that defines your rights to use the content.
If your device has OMA DRM protected content, to back up the content, use the
backup feature of Nokia PC Suite.
If your device has WMDRM protected content, both the activation keys and the
content will be lost if the device memory is formatted. You may also lose the
activation keys and the content in case the files on your device get corrupted.
Losing the activation keys or the content may limit your ability to use the same
content on your device again. For more information, contact your service
provider.
11
G e t s t a r t e d
2. Get started
■ Install SIM card and battery
Always switch the device off and disconnect the charger before removing the
battery.
Keep all SIM cards out of the reach of small children.
For availability and information on using SIM card services, contact your SIM
card vendor. This may be the service provider, network operator, or other vendor.
This device is intended for use with BL-5B battery. Always use original Nokia
batteries. See “Nokia battery authentication,” p. 80.
To install the SIM card, do the following:
1. To remove the back cover of
the phone, push the back
cover release button (1), and
detach the back cover away
from the phone (2). Remove
the battery as shown (3).
2. Open the SIM card holder (4),
and insert the SIM card
properly into the holder (5).
Close the SIM card holder (6).
12
G e t s t a r t e d
3. Replace the battery (7). Slide
the back cover into its place
(8, 9).
■ Charge the battery
Warning: Use only batteries, chargers, and enhancements approved by
Nokia for use with this particular model. The use of any other types may
invalidate any approval or warranty, and may be dangerous.
Check the model number of any charger before use with this device. This device is
intended for use when supplied with power from an AC-3 or AC-4 charger.
For availability of approved enhancements, please check with your dealer.
When you disconnect the power cord of any enhancement, grasp and pull the
plug, not the cord.
Connect the charger to a wall socket and the lead
from the charger to the connector on the bottom
of your phone.
If the battery is completely discharged, it may
take a few minutes before the charging indicator
appears on the display or before any calls can be
made.
The charging time depends on the charger used. Charging a BL-5B battery with
the AC-3 charger takes approximately 3 hours while the phone is in the standby
mode.
■ Memory card installation
Keep all microSD memory cards out of the reach of small
children.
13
G e t s t a r t e d
Use only compatible microSD cards with this device. Other memory cards, such as
reduced size multimedia cards, do not fit in the microSD card slot and are not
compatible with this device. Using an incompatible memory card may damage
the memory card as well as the device, and data stored on the incompatible card
may be corrupted.
Insert a microSD card
1. Remove the back cover of the phone.
2. Insert the card into the microSD card slot with the
contact surface facing backwards, and press it until it
locks into place.
3. Close the back cover of the phone.
Use only microSD cards approved by Nokia for use with
this device. Nokia utilizes the approved industry
standards for memory cards but not all other brands may
function correctly or be fully compatible with this device.
Remove the microSD card
Important: Do not remove the microSD card in the middle of an
operation when the card is being accessed. Removing the card in the
middle of an operation may damage the memory card as well as the
device, and data stored on the card may be corrupted.
1. Make sure that no application is currently accessing the microSD memory
card.
2. Remove the back cover of the phone.
3. Press the microSD card slightly in to release the lock, and remove the microSD
card from the slot.
■ Open the slide phone
To open the slide of the phone, push the upper part of the phone up.
■ Switch the phone on and off
Warning: Do not switch the phone on when wireless phone use is
prohibited or when it may cause interference or danger.
14
G e t s t a r t e d
Press and hold the power key. See “Keys and parts,” p. 17. If the phone asks for a
PIN or a UPIN code, enter the code (displayed as ****), and select OK.
Set the time and date
Enter the local time, select the time zone of your location in terms of the time
difference with respect to Greenwich Mean Time (GMT), and enter the date. See
“Time and date,” p. 40.
Plug and play service
When you switch on your phone for the first time, and the phone is in the standby
mode, you may be asked to get the configuration settings from your service
provider (network service dependency). Confirm or decline the query. See
“Connect to support,” p. 48, and “Configuration settings service,” p. 10.
■ Antenna
Your device has an internal antenna.
Note: As with any other radio
transmitting device, do not touch the
antenna unnecessarily when the
device is switched on. Contact with
the antenna affects call quality and
may cause the device to operate at a
higher power level than otherwise
needed. Avoiding contact with the
antenna area when operating the
device optimizes the antenna
performance and the battery life.
■ Headset
The headset in the sales box has been approved by Nokia for use with this device.
Always listen to music at a moderate level. Please be advised to pay special
attention to volume level in case you connect any other headsets to the device.
Do not connect products that create an output signal, as this may cause damage
to the device. Do not connect any voltage source to this connector.
15
G e t s t a r t e d
Audio adaptor
Use an audio adaptor AD-50 to connect a headphone with a 3.5-mm plug to your
phone. If the adaptor is connected to the phone the earpiece of the phone will be
disconnected.
Please note that the adaptor does not support a microphone line.
■ Phone strap
Thread a strap through the eyelet of the phone as
shown in the picture and tighten it.
16
Y o u r p h o n e
3. Your phone
■ Keys and parts
Earpiece (1)
Music player, rewind (2)
Music player, start, stop (3)
Enhancements connector (4)
Music player, fast forward (5)
Call key (6)
Left, middle, and right selection keys (7)
End key (8)
Scroll keys (9)
Keypad (10)
Charger connector (11)
USB connector (12)
Power key (13)
Phone strap eyelet (14)
Camera lens (15)
Volume up/ PTT key (16)
Volume down (17)
Camera key (18)
Infrared port (19)
Selfportrait viewfinder (20)
Loudspeaker (21)
17
Y o u r p h o n e
■ Standby mode
When the phone is ready for use, and you have not entered any characters, the
phone is in the standby mode.
Display
Signal strength of the cellular network (1)
Battery charge status (2)
Indicators (3)
Network name or operator logo (4)
Clock (5)
Main screen (6)
Function of left selection key (7) is Go to or a
shortcut to another function. See “Left selection
key,”p. 41.
Function of middle selection key (8) is Menu.
Function of right selection key (9) is Phonebk. or a shortcut to another function.
See “Right selection key,” p. 41. Operator variants may have an operator-specific
name.
Active standby
In the active standby mode there is a list of selected phone features and
information on the screen that you can directly access. To switch it on or off,
select Menu > Settings > Display > Active standby > Active standby mode > On
or Off.
In the standby mode, scroll up or down to activate the navigation in the list, and
select Select or View. Left and right arrows at the beginning and end of a line
indicate that further information is available by scrolling left or right. To end the
active standby mode, select Exit.
To organize and change the active standby mode, activate the navigation mode,
and select Options and from the available options.
18
Y o u r p h o n e
■ Indicators and icons
Your phone has two types of identifiers: indicators and icons.
Indicators
See “Standby mode,” p. 18 for information on indicators.
Icons
Icons are graphical representations of a specific item or situation. The following
list describes each icon.
You have unread messages.
You have unsent, canceled, or failed messages.
The phone registered a missed call.
,
Your phone is connected to the instant messaging service, and the
availability status is online or offline.
You received one or several instant messages.
The keypad is locked.
The phone does not ring for an incoming call or text message.
The alarm clock is activated.
The countdown timer is running.
The stopwatch is running.
,
The phone is registered to the GPRS or EGPRS network.
A GPRS or EGPRS connection is established.
The GPRS or EGPRS connection is suspended (on hold).
A Bluetooth connection is active.
,
,
If you have two phone lines, the second phone line is selected.
All incoming calls are forwarded to another number.
The loudspeaker is activated, or the music stand is connected to the
phone.
19
Y o u r p h o n e
Calls are limited to a closed user group.
The timed profile is selected.
,
,
, or
A headset, hands-free, loopset, or music stand enhancement is
connected to the phone.
■ Flight mode
You can deactivate all radio frequency functionality and still have access to
offline games, calendar, and phone numbers. Use the flight mode in radio
sensitive environments—on board aircraft or in hospitals. When the flight mode
is active,
is shown.
Select Menu > Settings > Profiles > Flight > Activate or Customize.
To deactivate the flight mode, select any other profile.
In the flight mode you can make an emergency call. Enter the emergency number,
press the call key, and select Yes when asked Exit flight profile? The phone
attempts to make an emergency call.
■ Keypad lock (keyguard)
To prevent the keys from being accidentally pressed, close the phone, and select
Lock within 3.5 seconds.
To unlock the keypad, select Unlock > Ok, or open the phone. If the security
keyguard is activated, enter the security code if requested.
To answer a call when the keyguard is on, press the call key or open the phone.
When you end or decline the call, the keypad automatically locks.
For Security keyguard, see “Phone,” p. 47.
When the keyguard is on, calls still may be possible to the official emergency
number programmed into your device.
20
Y o u r p h o n e
■ Functions without a SIM card
Several functions of your phone may be used without installing a SIM card (for
example, the data transfer with a compatible PC or another compatible device).
Some functions appear dimmed in the menus and cannot be used.
For an emergency call, some networks may require that a valid SIM card is
properly inserted in the device.
21
C a l l f u n c t i o n s
4. Call functions
■ Make a call
1. Push the upper part of the phone up.
2. Enter the phone number, including the area code.
For international calls, press twice for the international prefix (the +
*
character replaces the international access code), enter the country code, the
area code without the leading 0, if necessary, and the phone number.
3. To call the number, press the call key.
To increase the volume in a call, press + and to decrease, press - .
4. To end the call or to cancel the call attempt, press the end key, or close the
phone.
To search for a name or phone number that you have saved in Phonebook, see
“Search for a contact,” p. 34. Press the call key to call the number.
To access the list of dialed numbers, press the call key once in the standby mode.
To call the number, select a number or name, and press the call key.
■ 1-touch dialing
Assign a phone number to one of the 1-touch-dialing keys, 2 to 9. See “1-touch
dials,” p. 36. Call the number in either of the following ways:
•
•
Press a 1-touch-dialing key, then the call key.
If 1-touch dialing is set to On, press and hold a 1-touch-dialing key until the
call begins. See 1-touch dialing in “Call,” p. 46.
■ Enhanced voice dialing
You can make a phone call by saying the name that is saved in the contact list of
the phone. Voice commands are language-dependent. To set the language, see
Recognition lang. in “Phone,” p. 47.
22
C a l l f u n c t i o n s
Make a voice dialing call
Note: Using voice tags may be difficult in a noisy environment or during
an emergency, so you should not rely solely upon voice dialing in all
circumstances.
1. In the standby mode, press and hold the right selection key, or press and hold
the volume down key. A short tone is played, and Speak now is displayed.
2. Say the voice command clearly. If the voice recognition is successful, a list
with matches is shown. The phone plays the voice command of the match on
the top of the list. If the result is not the correct one, scroll to another entry.
Using voice commands to carry out a selected phone function is similar to
voice dialing. See Voice commands in “My shortcuts,” p. 41.
■ Answer or decline a call
To answer an incoming call, press the call key, or open the phone. To end the call,
press the end key, or close the phone.
To decline an incoming call, press the end key. To mute the ringing tone, select
Silence.
Call waiting
To answer the waiting call during an active call (network service dependency),
press the call key. The first call is put on hold. To end the active call, press the end
key.
To activate the Call waiting function, see “Call,” p. 46.
■ Options during a call
Many of the options that you can use during a call are network services. For
availability, contact your service provider.
During a call, select Options and from the following options:
Call options are Mute or Unmute, Phonebook, Menu, Lock keypad, Record, Voice
clarity, Loudspeaker or Handset.
Network services options are Answer or Decline, Hold or Resume, New call, Add to
conference, End call, End all calls, and the following:
Touch tones — to send tone strings
23
C a l l f u n c t i o n s
Swap — to switch between the active call and the call on hold
Transfer calls — to connect a call on hold to an active call and disconnect yourself
Conference — to make a conference call
Private call —to discuss privately in a conference call
Warning: Do not hold the device near your ear when the loudspeaker is
in use, because the volume may be extremely loud.
24
N a v i g a t e t h e m e n u s
5. Navigate the menus
The phone offers you an extensive range of functions, which are grouped into
menus.
1. To access the menu, select Menu.
To change the menu view, select Options > Main menu view > List, Grid, Grid
with labels, or Tab.
To rearrange the menu, scroll to the menu you want to move, and select
Options > Organize > Move. Scroll to where you want to move the menu, and
select OK. To save the change, select Done > Yes.
2. Scroll through the menu, and select an option (for example, Settings).
3. If the selected menu contains further submenus, select the one that you want
(for example, Call).
4. If the selected menu contains further submenus, repeat step 3.
5. Select the setting of your choice.
6. To return to the previous menu level, select Back. To exit the menu, select
Exit.
25
M e s s a g i n g
6. Messaging
You can read, write, send, and save text and picture messages, postcards, and
voice notes. All messages are organized into folders.
■ Text messages
With the short message service (SMS) you can send and receive text messages,
and receive messages that can contain pictures (network service dependency).
Before you can send any text or SMS e-mail message, you must save your
message center number. See “Message settings,” p. 32.
To check SMS e-mail service availability and to subscribe to the service, contact
your service provider. To save an e-mail address in Phonebook, see “Save details,”
p. 34.
Your device supports the sending of text messages beyond the character limit for
a single message. Longer messages will be sent as a series of two or more
messages. Your service provider may charge accordingly. Characters that use
accents or other marks, and characters from some language options like Chinese,
take up more space limiting the number of characters that can be sent in a single
message.
An indicator at the top of the display shows the total number of characters left
and the number of messages needed for sending. For example, 673/2 means that
there are 673 characters left and that the message will be sent as a series of 2
messages.
Text entry
To enter text (for example, when writing messages), use traditional or predictive
text input. When you write text, press and hold Options to toggle between
traditional text input, indicated by
. Not all languages are supported by predictive text input.
The character cases are indicated by , and . To change the
, and predictive text input, indicated by
,
character case, press #. To change from the letter to number mode, indicated by
, press and hold #, and select Number mode. To change from the number to
the letter mode, press and hold #.
To set the writing language, select Options > Writing language.
26
M e s s a g i n g
Predictive text input
Predictive text input is based on a built-in dictionary to which you can also add
new words.
1. Start writing a word using the keys, 2 to 9. Press each key only once for one
letter.
2. When you finish writing the word and it is correct, to confirm it by adding a
space, press 0.
If the word is not correct, press repeatedly, and select the word from the
*
list.
If the ? character is displayed after the word, the word you intended to write
is not in the dictionary. To add the word to the dictionary, select Spell. Enter
the word using traditional text input, and select Save.
To write compound words, enter the first part of the word, and press the scroll
key right to confirm it. Write the last part of the word, and confirm the word.
3. Start writing the next word.
Traditional text input
Press a number key, 1 to 9, repeatedly until the desired character appears. The
characters available depend on the selected writing language. If the next letter
you want is located on the same key as the present one, wait until the cursor
appears and enter the letter. The most common punctuation marks and special
characters are available under the number key 1.
Write and send a message
1. Select Menu > Messaging > Create message > Text message.
2. Enter one or more phone numbers or e-mail addresses in the To: field. To
retrieve a phone number or e-mail address from a memory, select Add.
3. For a SMS e-mail, enter a subject in the Subject: field.
4. Write your message in the Message: field.
5. To send the message, select Send. See “Message sending,” p. 28.
Read and reply to a message
1. To view a received message, select Show. To view it later, select Exit.
27
M e s s a g i n g
To read the message later, select Menu > Messaging > Inbox.
2. To reply to a message, select Reply > Text message, Picture message, or Voice
notes.
3. Write the reply message.
4. To send the message, select Send. See “Message sending,” p. 28.
■ Picture message
Note: Only devices that have compatible features can receive and
display multimedia messages. The appearance of a message may vary
depending on the receiving device.
A multimedia message can contain some attachments.
To check availability and to subscribe to the multimedia messaging service
(MMS, network service), contact your service provider. See “Message settings,”
p. 32.
Write and send a picture message
The wireless network may limit the size of multimedia messages. If the inserted
image exceeds this limit, the device may make it smaller so that it can be sent by
MMS.
1. Select Menu > Messaging > Create message > Picture message.
2. Write your message. To add a file, select Insert and from the options.
3. To view the message before sending it, select Options > Preview.
4. To send the message, select Send. See “Message sending,” p. 28.
5. Enter one or more phone numbers or e-mail addresses in the To: field. To
retrieve a phone number or e-mail address from a memory, select Add.
6. To send the message, select Send. See “Message sending,” p. 28.
Message sending
To send the message, select Send. The phone saves the message in the Outbox
folder, and the sending starts.
28
M e s s a g i n g
Note: When the phone is sending the message, the animated
is
shown. This is an indication that the message has been sent by your
device to the message center number programmed into your device.
This is not an indication that the message has been received at the
intended destination. For more details about messaging services, check
with your service provider.
If an interruption occurs while the message is being sent, the phone tries to
resend the message a few times. If these attempts fail, the message remains in
the Outbox folder. To cancel the sending of the messages in the Outbox folder,
scroll to the desired message, and select Options > Cancel sending.
Read and reply to a message
Important: Exercise caution when opening messages. Multimedia
message objects may contain malicious software or otherwise be
harmful to your device or PC.
1. To view a received message, select Show. To view it later, select Exit.
2. To view the whole message if the received message contains a presentation,
select Play.
To view the files in the presentation or the attachments, select Options >
Objects or Attachments.
3. To reply to the message, select Options > Reply > Text message, Picture
message, Postcard, Flash message, or Voice notes.
4. Write the reply message.
5. To send the message, select Send. See “Message sending,” p. 28.
■ Postcards
Before you can use the postcard service you must subscribe to the service. To
check the availability, and costs, and to subscribe to the service if available,
contact your network operator or service provider.
With the postcard messaging service (network service dependency), create and
send postcards that may contain an image and a greeting text. The postcard is
sent to the service provider using multimedia messaging. The service provider
prints the postcard and sends it to the postal address given with the message.
MMS must be activated before this service can be used.
29
M e s s a g i n g
To send a postcard, select Menu > Messaging > Create message > Postcard. Fill
in the address, mandatory editor fields are marked by a *. Scroll to the image
field, select Insert and an image from the gallery, or New image to insert a recent
image; then write your greeting text. To send the message, select Send.
■ Nokia Xpress audio messaging
You can use the MMS to create and send an audio message in a convenient way.
MMS must be activated before you can use audio messages.
Create a message
1. Select Menu > Messaging > Create message > Voice notes. The recorder
opens. To use the recorder, see “Voice recorder,” p. 58.
2. Speak your message.
3. Enter one or more phone numbers in the To: field, or select Add to retrieve a
number.
4. To send the message, select Send.
Listen to a message
To open a received audio message, select Play; or if more than one message is
received, select Show > Play. To listen to the message later, select Exit.
■ Memory full
When you receive a message, and the memory for the messages is full, Memory
full. Unable to receive messages. is shown. To first delete old messages, select
OK > Yes and the folder. Scroll to the desired message, and select Delete. If more
messages are to be deleted, select Mark. Mark all the messages you want to
delete, and select Options > Delete marked.
■ Folders
The phone saves received messages in the Inbox folder.
Messages that have not yet been sent are saved in the Outbox folder.
To set the phone to save the sent messages in the Sent items folder, see Save sent
messages in “General settings,” p. 32.
30
M e s s a g i n g
To edit and send messages that you have written and saved in the Drafts folder,
select Menu > Messaging > Drafts.
You can move your messages to the Saved items folder. To organize your Saved
items subfolders, select Menu > Messaging > Saved items. To add a folder, select
Options > Add folder. To delete or rename a folder, scroll to the desired folder,
and select Options > Delete folder or Rename folder.
Your phone has templates. To create a new template, save a message as a
template. To access the template list, select Menu > Messaging > Saved items >
Templates.
■ Voice messages
The voice mailbox is a network service to which you may need to subscribe. For
more information contact your service provider.
To call your voice mailbox, select Menu > Messaging > Voice mail > Listen to
voice mails. To enter, search for, or edit your voice mailbox number, select Voice
mailbox no..
If supported by the network,
indicates new voice messages. To call your
voice mailbox number, select Listen.
■ Info messages
You can receive messages on various topics from your service provider (network
service dependency). For more information, contact your service provider. Select
Menu > Messaging > Info messages and from the available options.
■ Service commands
Write and send service requests (USSD commands) to your service provider (such
as activation commands for network services). Select Menu > Messaging > Serv.
commands.
■ Delete messages
To delete messages, select Menu > Messaging > Delete messages > By message
to delete single messages, By folder to delete all messages from a folder, or All
messages.
31
M e s s a g i n g
■ SIM messages
SIM messages are specific text messages that are saved to your SIM card. You
can copy or move those messages from the SIM to the phone memory, but not
vice versa. To read SIM messages, select Menu > Messaging > Options > SIM
messages.
■ Message settings
General settings
General settings are common for text and multimedia messages.
Select Menu > Messaging > Message settings > General settings and from the
following options:
Save sent messages > Yes — to set the phone to save the sent messages in the
Sent items folder
Overwriting in Sent > Allowed — to set the phone to overwrite the old sent
messages with the new ones when the message memory is full. This setting is
shown only if you set Save sent messages > Yes.
Font size — to select the font size used in messages
Graphical smileys > Yes — to set the phone to replace character-based smileys
with graphical ones
Text messages
The text message settings affect the sending, receiving, and viewing of text and
SMS e-mail messages.
Select Menu > Messaging > Message settings > Text messages and from the
following options:
Delivery reports > On — to ask the network to send delivery reports about your
messages (network service dependency)
Message centers > Add center — to set the phone number and name of the
message center that is required for sending text messages. You receive this
number from your service provider.
Msg. center in use — to select the message center in use
Message validity — to select the length of time for which the network attempts
to deliver your message
32
M e s s a g i n g
Messages sent via — to select the format of the messages to be sent: Text, Page,
or Fax (network service dependency)
Use packet data > Yes — to set GPRS as the preferred SMS bearer
Character support > Full — to select all characters in the messages to be sent as
viewed. If you select Reduced, characters with accents and other marks may be
converted to other characters.
Rep. via same center > Yes — to allow the recipient of your message to send you a
reply using your message center (network service dependency)
Picture messages
The message settings affect the sending, receiving, and viewing of picture
messages. You may receive the configuration settings for picture messaging as a
configuration message. See “Configuration settings service,” p. 10. You can also
enter the settings manually. See “Configuration,” p. 48.
Select Menu > Messaging > Message settings > Picture messages and from the
following options:
Delivery reports > On — to ask the network to send delivery reports about your
messages (network service dependency)
Image size (MMS) — to set the image size in picture messages.
Default slide timing — to define the default time between slides in picture
messages
Allow p. msg receptn. > Yes or No — to receive or block the picture message. If
you select In home network, you cannot receive picture messages when outside
your home network. The default setting of the picture message service is
generally Yes. The availability of this menu depends on your phone.
Incoming pic. msgs. — to allow the reception of picture messages automatically,
manually after being prompted, or to decline the reception. This setting is not
shown if Allow p. msg receptn. is set to No.
Allow ads — to receive or decline advertisements. This setting is not shown if
Allow p. msg receptn. is set to No, or Incoming pic. msgs. is set to Reject.
Configuration sett. > Configuration — Only the configurations that support
picture messaging are shown. Select a service provider, Default, or Personal
config. for picture messaging. Select Account and a MMS account contained in
the active configuration settings.
33
P h o n e b o o k
7. Phonebook
You can save names and phone numbers (contacts) in the phone memory and in
the SIM card memory.
The phone memory may save contacts with additional details, such as various
phone numbers and text items. You can also save an image for a limited number
of contacts.
The SIM card memory can save names with one phone number attached to them.
The contacts saved in the SIM card memory are indicated by
.
■ Search for a contact
Select Menu > Phonebook > Names. Scroll through the list of contacts, or enter
the first characters of the name you are searching for.
■ Save names and phone numbers
Names and numbers are saved in the used memory. To save a name and phone
number, select Menu > Phonebook > Names > Options > Add new contact.
■ Save details
In the phone memory you can save different types of phone numbers, a tone or a
video clip, and short text items for a contact.
The first number you save is automatically set as the default number and is
indicated with a frame around the number type indicator (for example,
).
When you select a name from contacts (for example, to make a call), the default
number is used unless you select another number.
Make sure that the memory in use is Phone or Phone and SIM. See “Settings,” p.
36.
Search for the contact to which you want to add a detail, and select Details >
Options > Add detail. Select from the options available.
■ Copy or move contacts
To copy or move a contact from the phone contact memory to the SIM card
memory, or vice versa, select Menu > Phonebook > Names. Select the contact to
copy or move and Options > Copy contact or Move contact.
34
P h o n e b o o k
To copy or move several contacts, select the first contact to copy or move and
Options > Mark. Mark the other contacts, and select Options > Copy marked or
Move marked.
To copy or move all contacts from the phone contact memory to the SIM card
memory, or vice versa, select Menu > Phonebook > Copy contacts or Move
contacts.
The SIM card memory can save names with one phone number attached to them.
■ Edit contact details
Search for the contact, and select Details. To edit a name, number, or text item or
to change the image, select Options > Edit. To change the number type, scroll to
the desired number, and select Options > Change type. To set the selected
number as the default number, select Set as default.
■ Synchronize all
Synchronize your calendar, contacts data, and notes with a remote Internet
server (network service dependency). For details see “Synchronize from a server,”
p. 45.
■ Delete contacts
To delete all the contacts and the details attached to them from the phone or SIM
card memory, select Menu > Phonebook > Del. all contacts > From phone
memory or From SIM card.
To delete a contact, search for the desired contact, and select Options > Delete
contact.
To delete a number, text item, or an image attached to the contact, search for the
contact, and select Details. Scroll to the desired detail, and select Options >
Delete and from the options available.
■ Business cards
You can send and receive a person’s contact information from a compatible
device that supports the vCard standard as a business card.
To send a business card, search for the contact whose information you want to
send, and select Details > Options > Send business card.
35
P h o n e b o o k
When you have received a business card, select Show > Save to save the business
card in the phone memory. To discard the business card, select Exit > Yes.
■ Settings
Select Menu > Phonebook > Settings and from the following options:
Memory in use — to select the SIM card or phone memory for your contacts.
Select Phone and SIM to recall names and numbers from both memories. In that
case, when you save names and numbers, they are saved in the phone memory.
Phonebook view — to select how the names and numbers in Phonebook are
displayed
Name display — to select whether the contact’s first or last name is displayed
first
Font size — to set the font size for the list of contacts
Memory status — to view the free and used memory capacity
■ Groups
Select Menu > Phonebook > Groups to arrange the names and phone numbers
saved in the memory into caller groups with different ringing tones and group
images.
■ 1-touch dials
To assign a number to a 1-touch-dialing key, select Menu > Phonebook >
1-touch dialing, and scroll to the 1-touch-dialing number that you want.
Select Assign, or if a number has already been assigned to the key, select
Options > Change. Select Find and the contact you want to assign. If the 1-touch
dialing function is off, the phone asks whether you want to activate it. See also
1-touch dialing in “Call,” p. 46.
To make a call using the 1-touch-dialing keys, see “1-touch dialing,” p. 22.
■ Info, service, and my numbers
Select Menu > Phonebook and from one of these submenus:
Info numbers — to call the information numbers of your service provider if the
numbers are included on your SIM card (network service dependency)
Service numbers — to call the service numbers of your service provider if the
numbers are included on your SIM card (network service dependency)
36
P h o n e b o o k
My numbers — to view the phone numbers assigned to your SIM card, if the
numbers are included on your SIM card
37
L o g
8. Log
The phone registers your missed, received, and dialed calls if the network
supports it and the phone is switched on and within the network service area.
To view the information on your calls, select Menu > Log > Missed calls, Received
calls, or Dialed numbers. To view your recent missed and received calls and the
dialed numbers chronologically, select Call log. To view the contacts to whom
you most recently sent messages, select Msg. recipients.
To view the approximate information on your recent communications, select
Menu > Log > Call timers, Data counter, or Pack. data timer.
To view how many text and multimedia messages you have sent and received,
select Menu > Log > Message log.
Note: The actual invoice for calls and services from your service
provider may vary, depending on network features, rounding off for
billing, taxes, and so forth.
Some timers may be reset during service or software upgrades.
38
S e t t i n g s
9. Settings
Use this menu to set or change your profiles, themes, tone settings, personal
shortcuts, time and date settings, call settings, phone settings, main display
settings, mini display settings, enhancement settings, configuration settings,
security settings, and to restore factory settings.
■ Profiles
Your phone has various setting groups called profiles, for which you can
customize the phone tones for different events and environments.
Select Menu > Settings > Profiles, the desired profile and from the following
options:
Activate — to activate the selected profile
Customize — to personalize the profile. Select the setting you want to change,
and make the changes.
Timed — to set the profile to be active until a certain time (up to 24 hours) and
set the end time. When the time set for the profile expires, the previous profile
that was not timed becomes active.
■ Themes
A theme contains elements for personalizing your phone.
Select Menu > Settings > Themes and from the following options:
Select theme — to set a theme. A list of folders in Gallery opens. Open the Themes
folder, and select a theme.
Theme downloads — to open a list of links to download more themes
■ Tones
You can change the tone settings of the selected active profile.
Select Menu > Settings > Tones. You can find the same settings in the Profiles
menu. See Customize in “Profiles,” p. 39.
To set the phone to ring only for calls from phone numbers that belong to a
selected caller group, select Alert for. Scroll to the caller group you want or All
calls, and select Mark.
39
S e t t i n g s
Select Options > Save to save the settings or Cancel to leave the settings
unchanged.
If you select the highest ringing tone level, the ringing tone reaches its highest
level after a few seconds.
■ Display
Select Menu > Settings > Display and from the available options:
Wallpaper — to add the background image in the standby mode
Active standby — to switch the active standby mode on or off and to organize and
personalize the active standby mode.
Standby font color — to select the color for the texts in the standby mode
Navigation key icons — to display the icons of the current navigation key
shortcuts in the standby mode when active standby is off
Slide animation — to set your phone to display an animation and sound a tone
when you open and close the phone, depending on the theme
Screen saver > On — to set your phone to display a screen saver. To download
more screen savers, select Graphic downloads. To set the time after which the
screen saver is activated, select Time-out.
Power saver — to save some battery power. The date and a digital clock are
displayed when no function of the phone is used for a certain time.
Font size — to set the font size for messaging, contacts, and web pages
Operator logo — to set your phone to display or hide the operator logo.
Cell info display > On — to display the cell identity, if available from the network
■ Time and date
To change the time, time zone, and date settings, select Menu > Settings > Time
and date > Time, Date, or Auto-update of time (network service dependency).
When traveling to a different time zone, select Menu > Settings > Time and
date > Time > Time zone and the time zone of your location in terms of the time
difference with respect to Greenwich Mean Time (GMT) or Universal Time
Coordinated (UTC). The time and date are set according to the time zone and
enable your phone to display the correct sending time of received text or
multimedia messages. For example, GMT -5 denotes the time zone for New York
(USA), 5 hours west of Greenwich/London (UK).
40
S e t t i n g s
■ My shortcuts
With personal shortcuts you get quick access to often used functions of the
phone.
Left selection key
To select a function from the list, select Menu > Settings > My shortcuts > Left
selection key.
If the left selection key is Go to to activate a function, in the standby mode, select
Go to > Options and from the following options:
Select options — to add a function to the shortcut list or to remove one
Organize — to rearrange the functions on your personal shortcut list
Right selection key
To select a function from the list, select Menu > Settings > My shortcuts > Right
selection key.
Navigation key
To assign other phone functions from a predefined list to the navigation key
(scroll key), select Menu > Settings > My shortcuts > Navigation key.
Voice commands
To call contacts and carry out phone functions, say the voice commands. Voice
commands are language-dependent. To set the language, see Recognition lang.
in “Phone,” p. 47.
To select the phone functions to activate with a voice commands, select Menu >
Settings > My shortcuts > Voice commands and a folder. Scroll to a function.
indicates that the voice tag is activated. To activate the voice tag, select Add. To
play the activated voice command, select Play. To use voice commands, see
“Enhanced voice dialing,” p. 22.
To manage the voice commands, scroll to a phone function, and select from the
following options:
Edit or Remove — to change or deactivate the voice command of the selected
function
41
S e t t i n g s
Add all or Remove all — to activate or deactivate voice commands to all functions
in the voice commands list
■ Connectivity
You can connect the phone to a compatible device using a Bluetooth wireless
technology, infrared, or a USB data cable connection. You can also define the
settings for EGPRS dial-up connections.
Bluetooth wireless technology
This device is compliant with Bluetooth Specification 2.0 + EDR supporting the
following profiles: generic access, network access, generic object exchange,
hands-free, headset, object push, file transfer, dial-up networking, SIM access,
and serial port. To ensure interoperability between other devices supporting
Bluetooth technology, use Nokia approved enhancements for this model. Check
with the manufacturers of other devices to determine their compatibility with
this device.
There may be restrictions on using Bluetooth technology in some locations.
Check with your local authorities or service provider.
Features using Bluetooth technology or allowing such features to run in the
background while using other features, increase the demand on battery power
and reduce the battery life.
Bluetooth technology allows you to connect the phone to a compatible
Bluetooth device within 10 meters (32 feet). Since devices using Bluetooth
technology communicate using radio waves, your phone and the other devices do
not need to be in direct line-of-sight, although the connection can be subject to
interference from obstructions such as walls or from other electronic devices.
Set up a Bluetooth connection
Select Menu > Settings > Connectivity > Bluetooth and from the following
options:
Bluetooth > On or Off — to activate or deactivate the Bluetooth function.
indicates that Bluetooth is activated.
Search audio enhanc. — to search for compatible Bluetooth audio devices. Select
the device that you want to connect to the phone.
Paired devices — to search for any Bluetooth device in range. Select New to list
any Bluetooth device in range. Select a device and Pair. Enter an agreed
Bluetooth passcode of the device (up to 16 characters) to pair (associate) the
42
S e t t i n g s
device to your phone. You must only give this passcode when you connect to the
device for the first time. Your phone connects to the device, and you can start
data transfer.
Bluetooth wireless connection
Select Menu > Settings > Connectivity > Bluetooth. To check which Bluetooth
connection is currently active, select Active devices. To view a list of Bluetooth
devices that are currently paired with the phone, select Paired devices.
Bluetooth settings
To define how your phone is shown to other Bluetooth devices, select Menu >
Settings > Connectivity > Bluetooth > My phone's visibility or My phone's name.
If you are concerned about security, turn off the Bluetooth function, or set My
phone's visibility to Hidden. Always accept only Bluetooth communication from
others with whom you agree.
Infrared
You can set up the phone to send and receive data through its infrared (IR) port
to or from a IRDA compatible phone or data device.
Do not point the IR beam at anyone's eyes or allow it to interfere with other IR
devices. Infrared devices are Class 1 laser products.
When sending or receiving data, ensure that the IR ports of the sending and
receiving devices are pointing at each other and that there are no obstructions
between the devices.
To activate or deactivate the IR port of your phone, select Menu > Settings >
Connectivity > Infrared.
If data transfer is not started within 2 minutes after the activation of the IR port,
the connection is cancelled and must be started again.
IR connection indicator
When
is shown continuously, the IR connection is activated, and your
phone is ready to send or receive data through its IR port.
When blinks, your phone is trying to connect to the other device, or a
connection has been lost.
43
S e t t i n g s
Packet data
General packet radio service (GPRS) is a network service that allows mobile
phones to send and receive data over an Internet protocol (IP)-based network.
To define how to use the service, select Menu > Settings > Connectivity > Packet
data > Packet data conn. and from the following options:
When needed — to set the packet data connection to established when an
application needs it. The connection will be closed when the application is
terminated.
Always online — to set the phone to automatically connect to a packet data
network when you switch the phone on
Modem settings
You can connect the phone using Bluetooth wireless technology or USB data
cable connection to a compatible PC and use the phone as a modem to enable
GPRS connectivity from the PC.
To define the settings for connections from your PC, select Menu > Settings >
Connectivity > Packet data > Packet data settings > Active access point, and
activate the access point you want to use. Select Edit active access pt. > Packet
data acc. pt., enter a name to change the access point settings, and select OK.
Select Packet data acc. pt., enter the access point name (APN) to establish a
connection to an network, and select OK.
You can also set the EGPRS dial-up service settings (access point name) on your
PC using the Nokia Modem Options software. See “Nokia PC Suite,” p. 76. If you
have set the settings both on your PC and on your phone, the PC settings are
used.
Data transfer
Synchronize your calendar, contacts data, and notes with another compatible
device (for example, a mobile phone), a compatible PC, or a remote Internet
server (network service dependency).
Your phone allows data transfer with a compatible PC or another compatible
device when using the phone without a SIM card.
Transfer contact list
To copy or synchronize data from your phone, the name of the device and the
settings must be in the list of transfer contacts. If you receive data from another
device (for example, a compatible mobile phone), the corresponding transfer
44
S e t t i n g s
contact is automatically added to the list, using the contact data from the other
device. Server sync and PC synchronization are the original items in the list.
To add a new transfer contact to the list (for example, a mobile phone), select
Menu > Settings > Connectivity > Data transfer > Options > Add transfer
contact > Phone synchronization or Phone copy, and enter the settings according
to the transfer type.
To edit the copy and synchronize settings, select a contact from the transfer
contact list and Options > Edit.
To delete a transfer contact, select it from the transfer contact list and Options >
Delete.
Data transfer with a compatible device
For synchronization use Bluetooth wireless technology or a cable connection. The
other device must be activated for receiving data.
To start data transfer, select Menu > Settings > Connectivity > Data transfer and
the transfer contact from the list other than Server sync or PC synchronization.
According to the settings, the selected data is copied or synchronized.
Synchronize from a compatible PC
To synchronize data from calendar, notes, and contacts, install the Nokia PC Suite
software on the PC. Use Bluetooth wireless technology or a USB data cable for
the synchronization, and start the synchronization from the PC.
Synchronize from a server
To use a remote Internet server, subscribe to a synchronization service. For more
information and the settings required for this service, contact your service
provider. You may receive the settings as a configuration message. See
“Configuration settings service,” p. 10 and “Configuration,” p. 48.
To start the synchronization from your phone, select Menu > Settings >
Connectivity > Data transfer > Server sync. Depending on the settings, select
Initializing syn-chronization or Initializing copy.
Synchronizing for the first time or after an interrupted synchronization may take
up to 30 minutes to complete.
USB data cable
You can use the USB data cable to transfer data between the phone and a
compatible PC or a printer supporting PictBridge. You can also use the USB data
cable with Nokia PC Suite.
45
S e t t i n g s
To activate the phone for data transfer or image printing, connect the data cable.
Confirm USB data cable connected. Select mode., and select from the following
options:
Nokia mode — to use the cable for PC Suite
Music sync — to use the phone with a PictBridge compatible printer or with your
compatible PC
Data storage — to connect to a PC that does not have Nokia software and use the
phone as a data storage device
To change the USB mode, select Menu > Settings > Connectivity > USB data
cable > Nokia mode, Printing, or Data storage.
■ Call
Select Menu > Settings > Call and from the following options:
Call forwarding — to forward your incoming calls (network service dependency).
You may not be able to forward your calls if some call restriction functions are
active. See Call restrictions in “Security,” p. 49.
Voice clarity > Active — to enhance speech intelligibility especially in noisy
environments
Anykey answer > On — to answer an incoming call by briefly pressing any key,
except the power key, the camera key, the left and right selection keys, or the end
key
Automatic redial > On — to make a maximum of 10 attempts to connect the call
after an unsuccessful call attempt
1-touch dialing > On — to dial the names and phone numbers assigned to the
1-touch-dialing keys, 2 to 9, by pressing and holding the corresponding number
key
Call waiting > Activate — to have the network notify you of an incoming call
while you have a call in progress (network service dependency). See “Call
waiting,” p. 23.
Summary after call > On — to briefly display the approximate duration and cost
(network service dependency) of the call after each call
Send my caller ID > Yes — to show your phone number to the person you are
calling (network service dependency). To use the setting agreed upon with your
service provider, select Set by network.
46
S e t t i n g s
Outgoing call line — to select the phone line 1 or 2 for making calls if supported
by your SIM card (network service dependency).
Slide call handling — to set the phone to answer calls when you open the phone
and to end calls when you close the phone
■ Phone
Select Menu > Settings > Phone and from the following options:
Language settings — To set the display language of your phone, select Phone
language. Automatic selects the language according to the information on the
SIM card. To select the USIM card language, select SIM language. To set a
language for the voice playback, select Recognition lang.. See “Enhanced voice
dialing,” p. 22 and Voice commands in “My shortcuts,” p. 41.
Security keyguard — to set the phone to ask for the security code when you
unlock the keyguard. Enter the security code, and select On.
Automatic keyguard — to lock the keypad automatically after a preset time delay
when the phone is in the standby mode and no function of the phone has been
used. Select On, and set the time.
Welcome note — to write the note that is shown when the phone is switched on
Flight query > On— The phone asks every time when it is switched on whether the
flight profile shall be used. With flight profile all radio connections are switched
off. The flight profile should be used in areas sensitive to radio emissions.
Phone updates — to receive phone software updates from your service provider
(network service dependency). This option may not be available, depending on
your phone. See “Phone software updates,” p. 50.
Operator selection > Automatic — to set the phone to automatically select one of
the cellular networks available in your area. With Manual you can select a
network that has a roaming agreement with your service provider.
Confirm SIM actions — See “SIM services,” p. 69.
Help text activation — to select whether the phone shows help texts
Start-up tone > On— The phone plays a tone when it is switched on.
■ Enhancements
This menu or the following options are shown only if the phone is or has been
connected to a compatible mobile enhancement.
47
S e t t i n g s
Select Menu > Settings > Enhancements. Select an enhancement, and
depending on the enhancement, from the following options:
Default profile — to select the profile that you want to be automatically activated
when you connect to the selected enhancement
Automatic answer — to set the phone to answer an incoming call automatically
after 5 seconds. If Incoming call alert is set to Beep once or Off, automatic answer
is off.
Lights — to set the lights permanently On. Select Automatic to set the lights on
for 15 seconds after a key press.
TTY/TDD > Use TTY > Yes — to use the text phone settings instead of headset or
loopset settings
■ Configuration
You can configure your phone with settings that are required for certain services
to function correctly. Your service provider may also send you these settings. See
“Configuration settings service,” p. 10.
Select Menu > Settings > Configuration and from the following options:
Default config. sett. — to view the service providers saved in the phone. To set the
configuration settings of the service provider as default settings, select Options >
Set as default.
Activ. def. in all apps. — to activate the default configuration settings for
supported applications
Preferred access pt. — to view the saved access points. Scroll to an access point,
and select Options > Details to view the name of the service provider, data
bearer, and packet data access point or GSM dial-up number.
Connect to support — to download the configuration settings from your service
provider
Device manager sett. — to allow or prevent the phone from receiving phone
software updates. This option may not be available, depending on your phone.
See “Phone software updates,” p. 50.
Personal config. sett. — to add new personal accounts for various services
manually and to activate or delete them. To add a new personal account if you
have not added any, select Add new; otherwise, select Options > Add new. Select
the service type, and select and enter each of the required parameters. The
parameters differ according to the selected service type. To delete or activate a
personal account, scroll to it, and select Options > Delete or Activate.
48
S e t t i n g s
■ Security
When security features that restrict calls are in use (such as call restrictions,
closed user group, and fixed dialing) calls still may be possible to the official
emergency number programmed into your device.
Select Menu > Settings > Security and from the following options:
PIN code request and UPIN code request — to set the phone to ask for your PIN or
UPIN code every time the phone is switched on. Some SIM cards do not allow the
code request to be turned off.
Call restrictions — to restrict incoming calls to and outgoing calls from your
phone (network service dependency). A restriction password is required.
Fixed dialing — to restrict your outgoing calls to selected phone numbers if this
function is supported by your SIM card. When the fixed dialing is on, GPRS
connections are not possible except while sending text messages over a GPRS
connection. In this case, the recipient’s phone number and the message center
number must be included in the fixed dialing list (network service dependency).
Closed user group — to specify a group of people whom you can call and who can
call you (network service dependency)
Security level > Phone — to set the phone to ask for the security code whenever a
new SIM card is inserted into the phone. If you select Memory, the phone asks for
the security code when the SIM card memory is selected, and you want to change
the memory in use.
Access codes — to change the security code, PIN code, PIN2 code, or restriction
password
Code in use — to select whether the PIN code should be active
PIN2 code request — to select whether the PIN2 code is required when using a
specific phone feature which is protected by the PIN2 code. Some SIM cards do
not allow the code request to be turned off.
Authority certificates or User certificates — to view the list of the authority or
user certificates downloaded into your phone. See “Certificates,” p. 74.
Security module sett. — to view Secur. module details, activate Module PIN
request, or change the module PIN and signing PIN. See also “Access codes,” p. 9.
■ Restore factory settings
To reset some of the menu settings to their original values, select Menu >
Settings > Rest. factory sett.. Enter the security code. The names and phone
numbers saved in Phonebook are not deleted.
49
S e t t i n g s
■ Phone software updates
Your service provider may send phone software updates over the air directly to
your device (network service dependency). This option may not be available,
depending on your phone.
Warning: If you install a software update, you cannot use the device,
even to make emergency calls, until the update is completed and the
device is restarted. Be sure to backup data before accepting a software
update.
Settings
To allowed or disallow phone software updates, select Menu > Settings >
Configuration > Device manager sett. >
Serv. softw. updates and following options:
Always allow — to perform all software downloads and updates automatically
Always reject — to decline all software updates
Confirm first — to perform software downloads and updates only after your
confirmation (default setting)
Request a software update
Select Menu > Settings > Phone > Phone updates to request available phone
software updates from your service provider. Select Current softw. details to
display the current software version and check whether an update is needed.
Select Downl. phone softw. to download and install a phone software update.
Follow the instructions on the display.
Install a software update
Select Install softw. update to start the installation, when the installation was
cancelled after the download.
The software update may take several minutes. If there are problems with the
installation, contact your service provider.
50
O p e r a t o r m e n u
10. Operator menu
This menu lets you access a portal to services provided by your network operator.
The name and the icon depend on the operator. For more information contact
your network operator. The operator can update this menu with a service
message. For more information, see “t-zones inbox,” p. 73.
51
G a l l e r y
11. Gallery
In this menu you can manage images, video clips, music files, themes, graphics,
tones, recordings, and received files. These files are stored in the phone memory
or an attached microSD memory card and may be arranged in folders.
Your phone supports an activation key system to protect acquired content.
Always check the delivery terms of any content and activation key before
acquiring them, as they may be subject to a fee.
To see the list of folders, select Menu > Fun & Apps > Gallery.
To see the available options of a folder, select a folder and Options.
To view the list of files in a folder, select a folder and Open.
To see the available options of a file, select a file and Options.
To view the folders of the memory card when moving a file, scroll to the memory
card, and press the scroll key right.
■ Print images
Your device supports Nokia XPressPrint. To connect it to a compatible printer use
a data cable or send the image via Bluetooth to a printer supporting Bluetooth
technology. See “Connectivity,” p. 42.
You can print images that are in the jpg format. The images taken with the
camera are automatically saved in the jpg format.
Select the image you want to print and Options > Print.
■ Memory card
Keep all memory cards out of the reach of small children.
You can use the microSD memory card to store your multimedia files such as
video clips, music tracks, and sound files, images, and messaging data, and to
back up information from phone memory.
Some of the folders in Gallery with content that the phone use (for example,
Themes) may be stored on the memory card.
To insert and remove the microSD memory card see “Insert a microSD card,” p. 14
and “Remove the microSD card,” p. 14.
52
G a l l e r y
Format the memory card
When a memory card is formatted, all data on the card is permanently lost. Some
memory cards are supplied preformatted and others require formatting. Consult
your retailer to find out if you must format the memory card before you can use
it.
To format a memory card, select Menu >Fun & Apps > Gallery or Games & Apps,
the memory card folder
, and Options > Format memory card > Yes.
When formatting is complete, enter a name for the memory card.
Lock the memory card
To set a password to lock your memory card to help prevent unauthorized use,
select Options > Set password. The password can be up to eight characters long.
The password is stored in your phone and you do not have to enter it again while
you are using the memory card on the same phone. If you want to use the
memory card on another phone, you are asked for the password. To delete the
password, select Options > Delete password.
Check memory consumption
To check the memory consumption of different data groups and the available
memory for installing new applications or software on your memory card, select
Options > Details.
53
M e d i a
12. Media
When taking and using images or video clips, obey all laws and respect local
customs as well as privacy and legitimate rights of others.
■ Camera and video
You can take images or record video clips with the built-in camera.
Take an image
To use the still image function, press the camera key in the standby mode, select
Menu > Fun & Apps >Media > Camera, or if the video function is on, scroll left or
right.
To take an image in landscape format,
hold the phone in a horizontal position.
To zoom in and out in the camera mode,
press the scroll key up and down or the
volume keys.
To take an image, select Capture, or press
the camera key. The phone saves the
images on the memory card (if installed).
Select Options to set Night mode on if the lighting is dim, Self-timer on to
activate the self-timer, or Img. sequence on to take images in a fast sequence.
With the highest image size setting, three images are taken in a sequence, with
other size settings, five images are taken.
Select Options > Settings >Image preview time and a preview time to display the
taken images on the display. During the preview time, select Back to take another
image or Send to send the image as a picture message.
Your device supports an image capture resolution of 1024 x 1280 pixels. The
image resolution in these materials may appear different.
Record a video clip
To have the video function, press and hold the camera key in the standby mode,
and select Menu > Fun & Apps > Media > Video, or if the camera function is on,
scroll left or right. To start the video recording, select Record. To pause the
54
M e d i a
recording, select Pause; to resume the recording, select Continue; to stop the
recording, select Stop. The phone saves the images on the memory card.
Camera and video options
To use a filter, select Options > Effects >Normal >False colors, Grayscale, Sepia,
Negative, or Solarize.
To change the camera and video settings, select Options > Settings.
■ Media player
With the media player you can view, play, and download files, such as images,
audio, video, and animated images. You can also view compatible streaming
videos from a network server (network service dependency).
Select Menu > Fun & Apps > Media > Media player > Open gallery, Bookmarks,
or Go to address to select or download media.
Select Menu > Fun & Apps > Media > Media player > FF/Rew interval to set the
step width for fast forward or rewind.
Configuration for a streaming service
You may receive the configuration settings required for streaming as a
configuration message from the service provider. See “Configuration settings
service,” p. 10. You can also enter the settings manually. See “Configuration,”
p. 48. To activate the settings, do the following:
1. Select Menu > Fun & Apps > Media > Media player > Streaming settings >
Configuration.
2. Select a service provider, Default, or Personal config. for streaming.
3. Select Account and a streaming service account contained in the active
configuration settings.
■ Music player
Your phone includes a music player for listening to music tracks, or other MP3,
AAC, AAC+, and enhanced AAC+ sound files that you have downloaded from the
Web or transferred to the phone with the Nokia Audio Manager application,
which is part of Nokia PC Suite. See “Nokia PC Suite,” p. 76.
55
M e d i a
Music files stored in the music folder in the phone memory or on the memory
card will automatically be detected and added to the music library during the
startup of the phone.
To open the music player, select Menu > Music player.
Playing the music tracks
Warning! Listen to music at a moderate level. Continuous exposure to
high volume may damage your hearing.
Operate the music player with the music player keys on the phone or with the
scroll keys.
To start playing, press
To adjust the volume level, use the volume keys on the side of the phone.
To pause the playing, press
To rewind the current track, press and hold
.
.
. To fast forward the current
. Release the key at the position you want to continue
track, press and hold
the music playback.
To skip to the next track, press
track, press
. To skip to the beginning of the previous
.
To close the music player and to continue music playback in the background,
press the end key.
To stop the music player, press and hold the end key.
Note: While the music player is open, the middle selection key and the
4-way scroll key can also be used to control the music player.
Music player options
Select from the following options:
Show tracks — View all available tracks of the active track list and play the
desired track. To play a track, scroll to the desired track, and select Play.
Music library — View all available tracks ordered according to Artists, Albums,
Genres, Composers, or Track lists. Select Update library to refresh the lists. Track
lists generated with the Nokia Music Manager are found under Track lists > My
track lists
Play options — Select Random to play the tracks on the track list in random order.
Select Repeat to play the current track or the entire track list repeatedly.
56
M e d i a
Media equalizer — to select or define an equalizer setting. See “Equalizer,” p. 59.
Add to Favorites — to add the current track to the favorite track list
Play via Bluetooth — to connect and play the tracks on an audio accessory using
Bluetooth technology
Send— to send the current track by a multimedia message or using Bluetooth
technology
Web page — to access a Web page associated with the currently played track.
Music downloads— to connect to a Web service.
Memory status — to view the free and used memory capacity
■ Radio
The FM radio depends on an antenna other than the wireless device’s antenna. A
compatible headset or enhancement needs to be attached to the device for the
FM radio to function properly.
Warning: Listen to music at a moderate level. Continuous exposure to
high volume may damage your hearing. Do not hold the device near
your ear when the loudspeaker is in use, because the volume may be
extremely loud.
Select Menu > Fun & Apps > Media > Radio.
To use the graphical keys
,
,
, or
on the display, scroll left or right
to the desired key, and select it.
Save radio frequencies
1. To start the search, select and hold
or . To change the radio frequency
in 0.05 MHz steps, briefly press
or
.
2. To save a frequency to a memory location, 1 to 9, press and hold the
corresponding number key. To save a frequency to a memory location from 10
to 20, press briefly 1 or 2, and press and hold the desired number key, 0 to 9.
3. Enter the name of the radio station.
Listen to the radio
Select Menu > Fun & Apps > Media > Radio. To scroll to the desired frequency,
select
or
, or press the headset key. To select a radio station, briefly press
the corresponding number keys. To adjust the volume, press the volume keys.
57
M e d i a
Select from the following options:
Turn off — to turn off the radio
Save station — to save a new station (shown if a new station is detected)
Loudspeaker or Headset — to listen to the radio using the loudspeakers or
headset.
Mono output or Stereo output — to listen to the radio in monophonic sound or in
stereo
Stations — to select the list of saved stations. To delete or rename a station, scroll
to the desired station, and select Options > Delete station, or Rename. Select
Visual service ID to enter a service ID given by the visual radio service provider
(network service dependency)
Search all stations — to search for new radio stations
Set frequency — to enter the frequency of the desired radio station
Station directory — to access a Web site with a list of radio stations
Enable visual service > Automatically — to set whether Visual Radio (network
service dependency) starts automatically when you turn on the radio.
Some radio stations may send text or graphical information that you can view
using the Visual Radio application. To check the availability and costs, contact
your service provider.
When an application using a packet data or HSCSD connection is sending or
receiving data, it may interfere with the radio.
■ Voice recorder
You can record pieces of speech, sound, or an active call, and save them in
Gallery. This is useful when recording a name and phone number to write down
later.
The recorder cannot be used when a data call or GPRS connection is active.
Record sound
1. Select Menu > Fun & Apps > Media > Voice recorder.
To use the graphical keys
,
, or
on the display, scroll left or right to
the desired key, and select it.
2. To start the recording, select
. To start the recording during a call, select
Options > Record. While recording a call, all parties to the call hear a faint
58
M e d i a
beeping. When recording a call, hold the phone in the normal position near to
your ear. To pause the recording, select
.
3. To end the recording, select
. The recording is saved in Gallery >
Recordings.
To listen to the latest recording, select Options > Play last recorded.
To send the last recording, select Options > Send last recorded.
To see the list of recordings, select Menu > Fun & Apps > Gallery >
Recordings.
■ Equalizer
You can control the sound quality when using the music player by amplifying or
diminishing frequency bands.
Select Menu > Fun & Apps > Media > Equalizer.
To activate a set, scroll to one of the equalizer sets, and select Activate.
To view, edit, or rename a selected set, select Options > View, Edit, or Rename.
Not all sets can be edited or renamed.
■ Stereo widening
Stereo widening enhances the audio output of the phone by enabling a wider
stereo sound effect. To change the setting, select Menu > Fun & Apps > Media >
Stereo widening.
59
O r g a n i z e r
13. Organizer
Your Nokia mobile phone has many useful features for organizing your everyday life.
The following features are found in Organizer: alarm clock, calendar, to-do list,
notes, calculator, countdown timer, and stopwatch.
■ Alarm clock
You can set the phone to alarm at a desired time. Select Menu > Fun & Apps >
Organizer > Alarm clock.
To set the alarm, select Alarm time, and enter the alarm time. To change the
alarm time when the alarm time is set, select On.
To set the phone to alert you on selected days of the week, select Repeat alarm.
To select the alarm tone or set the radio as the alarm tone, select Alarm tone. If
you select the radio as an alarm tone, connect the headset to the phone.
To set a snooze time-out, select Snooze time-out and the time.
Stop the alarm
The phone sounds an alert tone even if the phone was switched off. To stop the
alarm, select Stop. If you let the phone continue to sound the alarm for a minute
or select Snooze, the alarm stops for the time you set in Snooze time-out, then
resumes.
If the alarm time is reached while the device is switched off, the device switches
itself on and starts sounding the alarm tone. If you select Stop, the device asks
whether you want to activate the device for calls. Select No to switch off the
device or Yes to make and receive calls. Do not select Yes when wireless phone
use may cause interference or danger.
■ Calendar
Select Menu > Fun & Apps > Organizer > Calendar.
The current day is indicated by a frame. If there are any notes set for the day, the
day is in bold type, and the beginning of the note is shown below the calendar. To
view the day notes, select View. To view a week, select Options > Week view. To
delete all notes in the calendar, select the month or week view, and select
Options > Delete all notes.
60
O r g a n i z e r
In Settings you can set the date, time, time zone, date or time format, date
separator, default view, or the first day of the week. In Auto-delete notes, you can
set the phone to delete old notes automatically after a specified time.
Make a calendar note
Select Menu > Fun & Apps > Organizer > Calendar. Scroll to the date, and select
Options > Make a note and one of the following note types:
Call, Birthday, Memo, or Reminder. Fill in the fields.
Meeting,
Note alarm
The phone displays the note and if set, sounds a tone. With a call note
on the
display, to call the displayed number, press the call key. To stop the alarm and to
view the note, select View. To stop the alarm for 10 minutes, select Snooze.
To stop the alarm without viewing the note, select Exit.
■ To-do list
To save a note for a task that you must do, select Menu > Fun & Apps >
Organizer > To-do list.
To make a note if no note is added, select Add; otherwise, select Options > Add.
Fill in the fields, and select Save.
To view a note, scroll to it, and select View. While viewing a note, you can also
select an option to edit the attributes. You can also select an option to delete the
selected note and delete all the notes that you have marked as done.
■ Notes
To write and send notes, select Menu > Fun & Apps > Organizer > Notes.
To make a note if no note is added, select Add; otherwise, select Options > Make
a note. Write the note, and select Save.
■ Calculator
The calculator in your phone provides basic arithmetic and trigonometric
functions, calculates the square and the square root, the inverse of a number, and
converts currency values.
Note: This calculator has limited accuracy and is designed for simple
calculations.
61
O r g a n i z e r
Select Menu > Fun & Apps > Organizer > Calculator. Press # for a decimal point.
Scroll to the desired operation or function, or select it from the Options.
To set the exchange rate, select Options > Exchange rate.
■ Countdown timer
To start the countdown timer, select Menu > Fun & Apps > Organizer > Countd.
timer > Normal timer, enter the alarm time, and write a note text that is
displayed when the time expires. To start the countdown timer, select Start. To
change the countdown time, select Change time. To stop the timer, select Stop
timer.
To have an interval timer with up to 10 intervals started, first enter the intervals.
Select Menu >Fun & Apps > Organizer > Countd. timer > Interval timer. To start
the timer, select Start timer > Start.
■ Stopwatch
You can measure time, take intermediate times, or take lap times using the
stopwatch. During timing, the other functions of the phone can be used. To set
the stopwatch timing in the background, press the end key.
Using the stopwatch or allowing it to run in the background when using other
features increases the demand on battery power and reduces the battery life.
Select Menu > Fun & Apps > Organizer > Stopwatch and from the following
options:
Split timing — to take intermediate times. To start the time observation, select
Start. Select Split every time that you want to take an intermediate time. To stop
the time observation, select Stop.
To save the measured time, select Save.
To start the time observation again, select Options > Start. The new time is added
to the previous time. To reset the time without saving it, select Reset.
Lap timing — to take lap times
Show last time — to view the most recently measured time if the stopwatch is not
reset
View times or Delete times — to view or delete the saved times
62
G a m e s a n d A p p l i c a t i o n s
14. Games and Applications
Use the Games & Apps menu to manage games and applications. These files are
stored in the phone memory or an attached microSD memory card and can be
arranged in folders.
For options to format or lock and unlock the memory card see “Memory card,”
p. 52.
■ Launch a game
Your phone software includes some games.
Select Menu > Fun & Apps > Games & Apps > Games. Scroll to the desired game,
and select Open.
For games stored on the memory card, select Menu > Fun & Apps > Games &
Apps > Memory card > Games. Scroll to the desired game.
To set sounds, lights, and shakes for the game, select Menu > Fun & Apps >
Games & Apps > Options > Application settings. For more options, see
“Application options,” p. 63.
■ Launch an application
Your phone software includes some Java applications.
Select Menu > Fun & Apps > Games & Apps > Collection. Scroll to an
application, and select Open.
For applications stored on the memory card, select Menu > Fun & Apps > Games
& Apps > Memory card > Collection. Scroll to the desired application.
■ Application options
Update version — to check if a new version of the application is available for
download from t-zones (network service dependency)
Web page — to provide further information or additional data for the application
from an Internet page (network service dependency), if available
Application access — to restrict the application from accessing the network
63
G a m e s a n d A p p l i c a t i o n s
■ Download an application
Your phone supports J2ME Java applications. Make sure that the application is
compatible with your phone before downloading it.
Important: Only install and use applications and other software from
sources that offer adequate security and protection against harmful
software.
You can download new Java applications and games in different ways.
Use the Nokia Application Installer from PC Suite to download the applications to
your phone, or select Menu > Fun & Apps > Games & Apps > Options >
Downloads > App. downloads; the list of available bookmarks is shown. See
“Bookmarks,” p. 71.
For the availability of different services, pricing, and fees, contact your service
provider.
Your device may have some bookmarks loaded for sites not affiliated with Nokia.
Nokia does not warrant or endorse these sites. If you choose to access them, you
should take the same precautions, for security or content, as you would with any
Internet site.
64
I n s t a n t m e s s a g i n g
15. Instant messaging
You can take text messaging to the next level by experiencing instant messaging
(IM) (network service) in a wireless environment. You can engage in IM with
friends and family, regardless of the mobile system or platform (like the Internet)
they are using, as long as you all use the same IM service.
Before you can start using IM, you must first register with the instant messaging
service you want to use and obtain a unique ID and password before you can use
IM. See “Register with an IM service,”p. 65 for more information.
Note: Depending on your IM service provider, you may not have access
to all of the features described in this guide and your menus may be
different.
To check the availability and costs and to subscribe to the IM service, contact
your wireless service provider and the IM service provider from whom you receive
your unique ID, password, and settings.
While you are logged in and connected to the IM service, you can exit the IM
application and use the other functions of the phone, and the IM session and
conversations remain active in the background.
■ Register with an IM service
You can do this by registering over the Internet with the IM service provider you have
selected to use. During the registration process, you will have the opportunity to
create the unique ID and password ofyourchoice. For more information about signing
up for IM services, contact your wireless service provider or an IM service provider.
■ Login
1. Select Menu > I M.
A list of available IM services is displayed.
2. Select the IM service you want to use and enter your unique ID and password.
If you have already logged in to an IM service before, the unique ID you used
previously is displayed automatically.
3. Select Login.
Depending on the IM service provider you are using, these may not be the exact
menu items displayed.
65
I n s t a n t m e s s a g i n g
You can choose to save your password so you do not have to enter it each time
you sign in, or you can choose to log in automatically and skip the login menu
when you select the IM application.
■ Begin an IM session
You can send instant messages to anyone if you have the person’s unique ID and
you use the same IM service.
To begin an IM session, do the following:
1. From your contacts list, select a contact who is online.
Some IM service providers also allow sending instant messages to contacts
who are not online.
2. To send a message to a person who is not in your contacts list, select Options,
the option to send a message, and enter unique ID of the person.
A conversation menu is displayed, with the contact’s name displayed at the top.
3. Enter a message. When you finish the message, select Send.
■ Receive and reply to messages
If you have an active IM conversation open and receive an instant message from the
contact with whom you are chatting, the new message notification sound plays
and the message appears in the conversation. As the conversation progresses, the
most recent message appears at the bottom of the menu, causing the previous
messages to move up if the screen is full. To reply, enter your message and select Send.
If you receive an instant message when you have the IM application open, but do
not have an active conversation open, the new message notification sound plays.
Also, a new IM icon is displayed next to the name of the message sender under
the conversations section of the contacts list.
If you receive an instant message when you are logged in to the IM service but do
not have the IM application open on your phone, a message is displayed telling you
that a new IM message has been received. Select Start to open the IM application,
and view the new message.
■ Return to chat session
From the I M contacts list, select Conversations. This list displays all IM conversations
and group chats in which you are currently participating. To view a conversation
or continue chatting, select a group name or contact name.
66
I n s t a n t m e s s a g i n g
■ Contacts
You can add the names of contacts with whom you interact frequently by IM to
the contacts list.
Add a new contact
To add a contact to the contacts list, select Options > Add contact. Enter the
contact’s unique ID for the IM service and select OK.
Remove a contact
From the contacts list, select the contact you want to remove, and select
Options > Remove contact > OK.
■ Conversation options
You can save an open conversation to be available for viewing, even after you end
the conversation.
To save a conversation, while you have it open, select Options > Save, edit the name,
if you want, and select Save.
To view a saved conversation, from the contacts list, select Options> Saved convers.
Scroll to the conversation name you want, and select Open.
To rename a saved conversation, from the contacts list, select Options > Saved
convers. Scroll to the conversation name you want, and select Options > Rename.
Rename the conversation, and select OK.
To delete a saved conversation, from the contacts list, select Options > Saved
convers. Scroll to the conversation name you want, and select Options >
Delete > OK.
■ Set your availability
You can determine if other users can tell whether you are available or not.
From the contacts list, highlight your name at the top of the menu, and select
Options > My status > Available for all, Avail. for contacts, or Appear offline.
67
I n s t a n t m e s s a g i n g
■ Log off service
Exit the IM application
From the contacts list, you can exit the IM application but still be connected to
the IM service. Select Exit, confirm the selection, and select Exit again. If you
open IM again, you do not need to log in again.
You can receive instant messages from your contacts when using your phone for
other purposes, such as playing a game. If you are connected to your IM service,
but you have not used your IM application for some time, you may be automatically
disconnected from the IM service. The next time you open the IM application, you
must log in again.
Log out of IM
To disconnect from the IM service, you must log out. From the contacts list, select
Options > Logout > OK.
You are taken to the login screen of the IM service provider, where you can return
to the IM service provider selection list, exit the IM application, or select an IM
service and log in again.
68
S I M s e r v i c e s
16. SIM services
Your SIM card may provide additional services that you can access. This menu is
shown only if it is supported by your SIM card. The name and contents of the
menu depend on the available services.
For availability and information on using SIM card services, contact your SIM
card vendor. This may be the service provider, network operator, or other vendor.
To set the phone to show you the confirmation messages sent between your
phone and the network when you are using the SIM services, select Menu >
Settings > Phone > Confirm SIM actions > Yes.
Accessing these services may involve sending messages or making a phone call
for which you may be charged.
69
t - z o n e s
17. t-zones
You can access various mobile Internet services with your phone browser.
Important: Use only services that you trust and that offer adequate
security and protection against harmful software.
Check the availability of these services, pricing, fees, and instructions with your
service provider.
With the phone browser you can view the services that use wireless markup
language (WML) or extensible hypertext markup language (XHTML) on their
pages. Appearance may vary due to screen size. You may not be able to view all
details of the Internet pages.
■ Set up browsing
You may receive the configuration settings required for browsing as a
configuration message from the service provider that offers the service that you
want to use. See “Configuration settings service,” p. 10. You can also enter all the
configuration settings manually. See “Configuration,” p. 48.
■ Connect to a service
Ensure that the correct configuration settings of the service are activated.
1. To select the settings for connecting to the service, select Menu > t-zones >
Settings > Configuration sett..
2. Select Configuration. Only the configurations that support browsing service
are shown. Select a service provider, Default, or Personal config. for browsing.
See “Set up browsing,” p. 70.
3. Select Account and a browsing service account contained in the active
configuration settings.
4. Select Displ. term. window > Yes to perform manual user authentication for
intranet connections.
Make a connection to the service in one of the following ways:
•
•
•
Select Menu > t-zones > Home; or in the standby mode, press and hold 0.
To select a bookmark of the service, select Menu > t-zones > Bookmarks.
To select the last URL, select Menu > t-zones > Last web addr..
70
t - z o n e s
•
To enter the address of the service, select Menu > t-zones > Go to address.
Enter the address of the service, and select OK.
■ Browse pages
After you make a connection to the service, you can start browsing its pages. The
function of the phone keys may vary in different services. Follow the text guides
on the phone display. For more information, contact your service provider.
Browse with phone keys
To browse through the page, scroll in any direction.
To select an item, press the call key, or select Select.
To enter letters and numbers, press the 0 to 9 keys. To enter special characters,
press
.
*
Direct calling
While browsing, you can make a phone call, and save a name and a phone
number from a page.
■ Bookmarks
You can save page addresses as bookmarks in the phone memory.
1. While browsing, select Options > Bookmarks; or in the standby mode, select
Menu > t-zones > Bookmarks.
2. Scroll to a bookmark, and select it; or press the call key to make a connection
to the page associated with the bookmark.
3. Select Options to view, edit, delete, or send the bookmark; to create a new
bookmark; or to save the bookmark to a folder.
Your device may have some bookmarks loaded for sites not affiliated with Nokia.
Nokia does not warrant or endorse these sites. If you choose to access them, you
should take the same precautions, for security or content, as you would with any
Internet site.
Receive a bookmark
When you have received a bookmark that is sent as a bookmark, 1 bookmark
received is displayed. To view the bookmark, select Show.
71
t - z o n e s
■ Appearance settings
While browsing, select Options > Other options > Appearance settings; or in the
standby mode, select Menu > t-zones > Settings > Appearance settings and
from the following options:
Text wrapping — to select how the text shall appear on the display
Font size — to set the font size
Show images > No — to hide images on the page
Alerts > Alert for unsec. conn. > Yes — to set the phone to alert when a secure
connection changes to an unsecure one during browsing
Alerts > Alert for unsec. items > Yes — to set the phone to alert when a secure
page contains an unsecure item. These alerts do not guarantee a secure
connection. For more information, see “Browser security,” p. 74.
Character encoding > Content encoding — to select the encoding for the browser
page content
Character encoding > Unicode (UTF-8) addr. > On — to set the phone to send a
URL as a UTF-8 encoding
Screen size > Full or Small— to set the screen layout
JavaScript > Enable — to enable the Java scripts
■ Security settings
Cookies
A cookie is data that a site saves in the cache memory of your phone. Cookies are
saved until you clear the cache memory. See “Cache memory,” p. 74.
While browsing, select Options > Other options > Security > Cookie settings; or
in the standby mode, select Menu > t-zones > Settings > Security settings >
Cookies. To allow or prevent the phone from receiving cookies, select Allow or
Reject.
Scripts over secure connection
You can select whether to allow the running of scripts from a secure page. The
phone supports WML scripts.
72
t - z o n e s
While browsing, to allow the scripts, select Options > Other options > Security >
WMLScript settings; or in the standby mode, select Menu > t-zones > Settings >
Security settings > WMLScripts in conn. > Allow.
■ Download settings
To automatically save all downloaded files in Gallery, select Menu > t-zones >
Settings > Downloading sett. > Automatic saving > On.
■ t-zones inbox
The phone is able to receive service messages sent by your service provider
(network service dependency). Service messages are notifications (for example,
news headlines), and they may contain a text message or an address of a service.
To access the t-zones inbox in the standby mode, when you have received a
service message, select Show. If you select Exit, the message is moved to the
t-zones inbox. To access the t-zones inbox later, select Menu > t-zones > t-zones
inbox.
To access the t-zones inbox while browsing, select Options > Other options >
t-zones inbox. Scroll to the message you want, and to activate the browser and
download the marked content, select Go. To display detailed information on the
service notification or delete the message, select Options > Details or Delete.
t-zones inbox settings
Select Menu > t-zones > Settings > t-zones inbox sett..
To set whether you want to receive service messages, select t-zones messages >
On or Off.
To set the phone to receive service messages only from content authors approved
by the service provider, select Message filter > On. To view the list of the
approved content authors, select Trusted channels.
To set the phone to automatically activate the browser from the standby mode
when the phone has received a service message, select Autom. connection > On.
If you select Off, the phone activates the browser only after you select Go when
the phone has received a service message.
73
t - z o n e s
■ Cache memory
A cache is a memory location that is used to store data temporarily. If you have
tried to access or have accessed confidential information requiring passwords,
empty the cache after each use. The information or services you have accessed is
stored in the cache.
To empty the cache while browsing, select Options > Other options > Clear the
cache; in the standby mode, select Menu > t-zones > Clear the cache.
■ Browser security
Security features may be required for some services, such as online banking or
shopping. For such connections you need security certificates and possibly a
security module, which may be available on your SIM card. For more information,
contact your service provider.
Security module
The security module improves security services for applications requiring a
browser connection, and allows you to use a digital signature. The security
module may contain certificates as well as private and public keys. The
certificates are saved in the security module by the service provider.
To view or change the security module settings, select Menu > Settings >
Security > Security module sett..
Certificates
Important: Even if the use of certificates makes the risks involved in
remote connections and software installation considerably smaller,
they must be used correctly in order to benefit from increased security.
The existence of a certificate does not offer any protection by itself;
the certificate manager must contain correct, authentic, or trusted
certificates for increased security to be available. Certificates have a
restricted lifetime. If Expired certificate or Certificate not valid yet is
shown even if the certificate should be valid, check that the current
date and time in your device are correct.
Before changing any certificate settings, you must make sure that you
really trust the owner of the certificate and that the certificate really
belongs to the listed owner.
74
t - z o n e s
There are three kinds of certificates: server certificates, authority certificates, and
user certificates. You may receive these certificates from your service provider.
Authority certificates and user certificates may also be saved in the security
module by the service provider.
To view the list of the authority or user certificates downloaded into your phone,
select Menu > Settings > Security > Authority certificates or User certificates.
is displayed during a connection, if the data transmission between the
phone and the content server is encrypted.
The security icon does not indicate that the data transmission between the
gateway and the content server (or place where the requested resource is stored)
is secure. The service provider secures the data transmission between the
gateway and the content server.
Digital signature
You can make digital signatures with your phone if your SIM card has a security
module. Using the digital signature can be the same as signing your name to a
paper bill, contract, or other document.
To make a digital signature, select a link on a page (for example, the title of the
book you want to buy and its price). The text to sign is shown, which may include
the amount and date.
Check that the header text is Read and that the digital signature icon
is
shown.
If the digital signature icon does not appear, there is a security breach, and you
should not enter any personal data such as your signing PIN.
To sign the text, read all of the text first, and select Sign.
The text may not fit within a single screen. Therefore, make sure to scroll through
and read all of the text before signing.
Select the user certificate you want to use. Enter the signing PIN. The digital
signature icon disappears, and the service may display a confirmation of your
purchase.
75
P C c o n n e c t i v i t y
18. PC connectivity
You can send and receive e-mail, and access the Internet when your phone is
connected to a compatible PC through a Bluetooth, infrared, or a data cable
connection. You can use your phone with a variety of PC connectivity and data
communications applications.
■ Nokia PC Suite
With Nokia PC Suite you can synchronize contacts, calendar, notes, and to-do
notes between your phone and the compatible PC or a remote Internet server
(network service dependency). Download the PC Suite from the CD delivered with
your phone. You may find more information on the Nokia Web site at
www.nokiausa.com/support or your local Nokia Web site.
■ Packet data, HSCSD, and CSD
With your phone you can use the packet data, high-speed circuit switched data
(HSCSD), and circuit switched data (CSD, GSM data) data services. For availability
and subscription to data services, contact your network operator or service
provider. See “Modem settings,” p. 44.
The use of HSCSD services consumes the phone battery faster than normal voice
or data calls.
■ Bluetooth
Use the Bluetooth technology to connect your compatible Laptop to the Internet.
Your phone must have activated a service provider that supports Internet access
and your PC has to support Bluetooth PAN (Personal Area Network). After
connecting to the network access point (NAP) service of the phone and pairing
with your PC your phone automatically opens a packet data connection to the
Internet. PC Suite software installation is not necessary when using the NAP
service of the phone.
See “Bluetooth wireless technology,” p. 42.
■ Data communication applications
For information on using a data communication application, refer to the
documentation provided with it.
76
P C c o n n e c t i v i t y
Making or answering phone calls during a computer connection is not
recommended, as it might disrupt the operation.
For better performance during data calls, place the phone on a stationary surface
with the keypad facing downward. Do not move the phone by holding it in your
hand during a data call.
77
E n h a n c e m e n t s
19. Enhancements
If you want to enhance phone functionality, a
range of enhancements is available for you. You
can select any of these items to help accommodate
your specific communication needs.
Check the model number of any charger before use
with this device. This device is intended for use
when supplied with power from an AC-3 or AC-4
charger.
Warning: Use only batteries, chargers and enhancements approved by
Nokia for use with this particular model. The use of any other types may
invalidate any approval or warranty, and may be dangerous.
For availability of approved enhancements, please check with your dealer.
A few practical rules about accessories and enhancements:
•
•
Keep all accessories and enhancements out of the reach of small children.
When you disconnect the power cord of any accessory or enhancement, grasp
and pull the plug, not the cord.
•
•
Check regularly that enhancements installed in a vehicle are mounted and
are operating properly.
Installation of any complex car enhancements must be made by qualified
personnel only.
78
B a t t e r y i n f o r m a t i o n
20. Battery information
■ Charging and discharging
Your device is powered by a rechargeable battery. The full performance of a new
battery is achieved only after two or three complete charge and discharge cycles.
The battery can be charged and discharged hundreds of times, but it will
eventually wear out. When the talk and standby times are noticeably shorter
than normal, replace the battery. Use only Nokia approved batteries, and
recharge your battery only with Nokia approved chargers designated for this
device.
If a replacement battery is being used for the first time or if the battery has not
been used for a prolonged period, it may be necessary to connect the charger and
then disconnect and reconnect it to start the charging.
Unplug the charger from the electrical plug and the device when not in use. Do
not leave fully charged battery connected to a charger, since overcharging may
shorten its lifetime. If left unused, a fully charged battery will lose its charge over
time.
If the battery is completely discharged, it may take a few minutes before the
charging indicator appears on the display or before any calls can be made.
Use the battery only for its intended purpose. Never use any charger or battery
that is damaged.
Do not short-circuit the battery. Accidental short-circuiting can occur when a
metallic object such as a coin, clip, or pen causes direct connection of the
positive (+) and negative (-) terminals of the battery. (These look like metal strips
on the battery.) This might happen, for example, when you carry a spare battery
in your pocket or purse. Short-circuiting the terminals may damage the battery
or the connecting object.
Leaving the battery in hot or cold places, such as in a closed car in summer or
winter conditions, will reduce the capacity and lifetime of the battery. Always try
to keep the battery between 59°F and 77°F (15°C and 25°C). A device with a hot
or cold battery may not work temporarily, even when the battery is fully charged.
Battery performance is particularly limited in temperatures well below freezing.
Do not dispose of batteries in a fire as they may explode. Batteries may also
explode if damaged. Dispose of batteries according to local regulations. Please
recycle when possible. Do not dispose as household waste.
79
B a t t e r y i n f o r m a t i o n
■ Nokia battery authentication
Always use original Nokia batteries for your safety. To check that you are getting
an original Nokia battery, purchase it from an authorized Nokia dealer, look for
the Nokia Original Enhancements logo on the packaging, and inspect the
hologram label using the following steps:
Successful completion of the four steps is not a total assurance of the
authenticity of the battery. If you have any reason to believe that your battery is
not an authentic original Nokia battery, you should refrain from using it, and take
it to the nearest authorized Nokia service point or dealer for assistance. Your
authorized Nokia service point or dealer will inspect the battery for authenticity.
If authenticity cannot be verified, return the battery to the place of purchase.
Authenticate hologram
1. When looking at the hologram on the label, you
should see the Nokia connecting hands symbol from
one angle and the Nokia Original Enhancements
logo when looking from another angle.
2. When you angle the hologram left, right, down, and
up, you should see 1, 2, 3, and 4 dots on each side
respectively.
3. Scratch the side of the label to reveal a 20-digit
code, for example, 12345678919876543210. Turn
the battery so that the numbers are facing upwards.
The 20-digit code reads starting from the number at
the top row followed by the bottom row.
4. Confirm that the 20-digit code is valid by following
80
B a t t e r y i n f o r m a t i o n
What if your battery is not authentic?
If you cannot confirm that your Nokia battery with the hologram on the label is
an authentic Nokia battery, please do not use the battery. Take it to the nearest
authorized Nokia service point or dealer for assistance. The use of a battery that
is not approved by the manufacturer may be dangerous and may result in poor
performance and damage to your device and its enhancements. It may also
invalidate any approval or warranty applying to the device.
81
C a r e a n d m a i n t e n a n c e
Care and maintenance
Your device is a product of superior design and craftsmanship and should be
treated with care. The suggestions below will help you protect your warranty
coverage.
•
Keep the device dry. Precipitation, humidity and all types of liquids or
moisture can contain minerals that will corrode electronic circuits. If your
device does get wet, remove the battery and allow the device to dry
completely before replacing it.
•
•
•
Do not use or store the device in dusty, dirty areas. Its moving parts and
electronic components can be damaged.
Do not store the device in hot areas. High temperatures can shorten the life of
electronic devices, damage batteries, and warp or melt certain plastics.
Do not store the device in cold areas. When the device returns to its normal
temperature, moisture can form inside the device and damage electronic
circuit boards.
•
•
Do not attempt to open the device other than as instructed in this guide.
Do not drop, knock, or shake the device. Rough handling can break internal
circuit boards and fine mechanics.
•
•
•
•
•
Do not use harsh chemicals, cleaning solvents, or strong detergents to clean
the device.
Do not paint the device. Paint can clog the moving parts and prevent proper
operation.
Do not touch the main display with hard or angular materials. Objects like
earrings or jewelry may scratch the display.
Use a soft, clean, dry cloth to clean any lenses (such as camera, proximity
sensor, and light sensor lenses).
Use only the supplied or an approved replacement antenna. Unauthorized
antennas, modifications, or attachments could damage the device and may
violate regulations governing radio devices.
•
•
Use chargers indoors.
Always create a backup of data you want to keep (such as contacts and
calendar notes) before sending your device to a service facility.
All of the above suggestions apply equally to your device, battery, charger, or any
enhancement. If any device is not working properly, take it to the nearest
authorized service facility for service.
82
A d d i t i o n a l s a f e t y i n f o r m a t i o n
Additional safety information
Your device and its enhancements may contain small parts. Keep them out of the
reach of small children.
■ Operating environment
Remember to follow any special regulations in force in any area, and always
switch off your device when its use is prohibited or when it may cause
interference or danger. Use the device only in its normal operating positions. This
device meets RF exposure guidelines when used either in the normal use position
against the ear or when positioned at least 2.2 centimeters (7/8 inch) away from
the body. When a carry case, belt clip or holder is used for body-worn operation,
it should not contain metal and should position the device the above-stated
distance from your body.
To transmit data files or messages, this device requires a quality connection to
the network. In some cases, transmission of data files or messages may be
delayed until such a connection is available. Ensure that the above separation
distance instructions are followed until the transmission is completed.
Parts of the device are magnetic. Metallic materials may be attracted to the
device. Do not place credit cards or other magnetic storage media near the
device, because information stored on them may be erased.
■ Medical devices
Operation of any radio transmitting equipment, including wireless phones, may
interfere with the functionality of inadequately protected medical devices.
Consult a physician or the manufacturer of the medical device to determine if
they are adequately shielded from external RF energy or if you have any
questions. Switch off your device in health care facilities when any regulations
posted in these areas instruct you to do so. Hospitals or health care facilities may
be using equipment that could be sensitive to external RF energy.
Pacemakers
Pacemaker manufacturers recommend that a minimum separation of 6 inches
(15.3 centimeters) be maintained between a wireless phone and a pacemaker to
avoid potential interference with the pacemaker. These recommendations are
consistent with the independent research by and recommendations of Wireless
Technology Research. Persons with pacemakers should do the following:
83
A d d i t i o n a l s a f e t y i n f o r m a t i o n
•
Always keep the device more than 6 inches (15.3 centimeters) from the
pacemaker
•
•
Not carry the device in a breast pocket
Hold the device to the ear opposite the pacemaker to minimize the potential
for interference.
If you suspect interference, switch off your device, and move the device away.
Hearing aids
Some digital wireless devices may interfere with some hearing aids. If
interference occurs, consult your service provider.
■ Vehicles
RF signals may affect improperly installed or inadequately shielded electronic
systems in motor vehicles such as electronic fuel injection systems, electronic
antiskid (antilock) braking systems, electronic speed control systems, and air bag
systems. For more information, check with the manufacturer or its representative
of your vehicle or any equipment that has been added.
Only qualified personnel should service the device, or install the device in a
vehicle. Faulty installation or service may be dangerous and may invalidate any
warranty that may apply to the device. Check regularly that all wireless device
equipment in your vehicle is mounted and operating properly. Do not store or
carry flammable liquids, gases, or explosive materials in the same compartment
as the device, its parts, or enhancements. For vehicles equipped with an air bag,
remember that air bags inflate with great force. Do not place objects, including
installed or portable wireless equipment in the area over the air bag or in the air
bag deployment area. If in-vehicle wireless equipment is improperly installed and
the air bag inflates, serious injury could result.
Using your device while flying in aircraft is prohibited. Switch off your device
before boarding an aircraft. The use of wireless teledevices in an aircraft may be
dangerous to the operation of the aircraft, disrupt the wireless telephone
network, and may be illegal.
■ Potentially explosive environments
Switch off your device when in any area with a potentially explosive atmosphere
and obey all signs and instructions. Potentially explosive atmospheres include
areas where you would normally be advised to turn off your vehicle engine.
Sparks in such areas could cause an explosion or fire resulting in bodily injury or
even death. Switch off the device at refueling points such as near gas pumps at
service stations. Observe restrictions on the use of radio equipment in fuel
84
A d d i t i o n a l s a f e t y i n f o r m a t i o n
depots, storage, and distribution areas; chemical plants; or where blasting
operations are in progress. Areas with a potentially explosive atmosphere are
often but not always clearly marked. They include below deck on boats, chemical
transfer or storage facilities, vehicles using liquefied petroleum gas (such as
propane or butane), and areas where the air contains chemicals or particles such
as grain, dust, or metal powders.
■ Emergency calls
Important: Wireless phones, including this device, operate using radio
signals, wireless networks, landline networks, and user-programmed
functions. Because of this, connections in all conditions cannot be
guaranteed. You should never rely solely on any wireless device for
essential communications like medical emergencies.
To make an emergency call:
1. If the device is not on, switch it on. Check for adequate signal strength.
Some networks may require that a valid SIM card is properly inserted in the
device.
2. Press the end key as many times as needed to clear the display and ready the
device for calls.
3. Enter the official emergency number for your present location. Emergency
numbers vary by location.
4. Press the call key.
If certain features are in use, you may first need to turn those features off before
you can make an emergency call. If the device is in the offline or flight mode, you
must change the profile to activate the phone function before you can make an
emergency call. Consult this guide or your service provider for more information.
When making an emergency call, give all the necessary information as accurately
as possible. Your wireless device may be the only means of communication at the
scene of an accident. Do not end the call until given permission to do so.
■ Certification information (SAR)
This mobile device meets guidelines for exposure to radio waves
Your mobile device is a radio transmitter and receiver. It is designed not to
exceed the limits for exposure to radio waves recommended by international
guidelines. These guidelines were developed by the independent scientific
organization ICNIRP and include safety margins designed to assure the
protection of all persons, regardless of age and health.
85
A d d i t i o n a l s a f e t y i n f o r m a t i o n
The exposure guidelines for mobile devices employ a unit of measurement known
as the Specific Absorption Rate or SAR. The SAR limit stated in the ICNIRP
guidelines is 2.0 watts/kilogram (W/kg) averaged over 10 grams of tissue. Tests
for SAR are conducted using standard operating positions with the device
transmitting at its highest certified power level in all tested frequency bands. The
actual SAR level of an operating device can be below the maximum value
because the device is designed to use only the power required to reach the
network. That amount changes depending on a number of factors such as how
close you are to a network base station. The highest SAR value under the ICNIRP
guidelines for use of the device RM-147 at the ear is 0.66 W/kg.
Use of device accessories and enhancements may result in different SAR values.
SAR values may vary depending on national reporting and testing requirements
and the network band. Additional SAR information may be provided under
Your mobile device is also designed to meet the requirements for exposure to
radio waves established by the Federal Communications Commission (USA) and
Industry Canada. These requirements set a SAR limit of 1.6 W/kg averaged over
1 gram of tissue. The highest SAR value reported under this standard during
product certification for use at the ear for device type RM-147 is 0.90 W/kg and
when properly worn on the body is 0.51 W/kg. Information about this device can
authorization system using FCC ID: PPIRM-147.
Talk and standby times
■ Talk and standby times
This section provides information about battery talk times, and standby times.
Be aware that the information in this section is subject to change. For more
information, contact your service provider.
Operation times are estimates only and depend on signal strength, phone use,
network conditions, features used, battery age and condition (including charging
habits), temperatures to which the battery is exposed, and many other factors.
The following times are approximate with the BL-5B 860 mAhLi-ion battery:
Talk time: up to 3.2 hours
Standby time: up to 263 hours
86
A d d i t i o n a l s a f e t y i n f o r m a t i o n
■ Technical information
Feature
Weight
Size
Specification
3.76 ounces (106.5 grams)
Volume: 5.19 cubic inches (85 ccm)
Length: 3.64 inches (92.4 mm)
Width: 1.9 inches (48.2 mm)
Thickness: 0.82 inches (20.7 mm)
RM-147
GSM 850
Frequency range
824–849 MHz (TX)
869–894 MHz (RX))
GSM 1800
1710–1785 MHz (TX)
1805–1865 MHz (RX)
GSM 1900
1850–1910 MHz (TX)
1930–1990 MHz (RX)
Up to 2 W
Transmitter output
power
BL-5B, 860 mAh
3.7 V dc
Battery
Voltage
59°F to + 77°F
15°C to + 25°C
Operating temperature
87
Index
certificates 74
certification information 85
charge the battery 13
charger connector 17
clock settings 40
codes 9
Numerics
1-touch dialing 22, 36
A
access codes 9
active standby 18, 40
alarm clock 60
antenna 15
configuration 48
setting service 10
settings 15
connector
applications 63
audio
charger 17
USB 17
adaptor 16
contact
messages 30
search 34
contacts
B
1-touch dialing 36
copy 34
battery
delete 35
authentication 80
charging 13
edit 35
groups 36
charging, discharging 79
installation 12
Bluetooth 42, 76
bookmarks 71
browser
my numbers 36
save 34
service numbers 36
settings 36
cookies 72
appearance settings 72
bookmarks 71
security 72
countdown timer 62
set up 70
D
business cards 35
data
cable 45
communication 76
transfer 44
C
cache memory 74
calculator 61
calendar 60
call
date settings 40
digital signature 75
display 18, 40
downloads 10, 73
functions 22
options 23
settings 46
E
waiting 23
earpiece 17
EGPRS 44
emergency calls 85
end
call key 17
call register. See log.
calls 22–24
camera 54, 55
camera key 17
call 22
key 17
88
enhancements 47, 78
enhancements connector 17
equalizer 59
media player 55
memory
card 14, 52
explosive environments 84
full 30
menu 25
message
F
center number 26
folder 30
factory settings 49
FM radio 57
settings 32
font size 40
messages
audio message 30
delete 31
G
info messages 31
length indicator 26
postcards 29
service commands 31
text 26
gallery 52
games 63
general packet radio service 44, 76
GPRS. See general packet radio service.
voice message 31
MMS. See picture messages.
music player 55
H
handsfree. See loudspeaker.
Headset 15
hearing aid 84
N
navigation
key 41
I
menus 25
network
image 54
indicators 19
info messages 31
infrared
name on display 18
services 7
notes 61
connection 43
lens 17
numbers 36
installation 12
instant messaging 65
Internet 70
O
offline mode 21
operator menu 51
organizer 60
IR. See infrared.
K
keyguard 20
keypad 17, 20
keys 17
P
pacemakers 83
packet data
See general packet radio service.
parts 17
L
PC connectivity 76
PC Suite 76
language settings 47
log 38
phone
loudspeaker 17, 23
configuration 48
open 14
M
settings 47
maintenance 82
updates 47, 50
89
phone lock. See keypad lock.
PictBridge 45
enhancements 47
fold animation 40
GPRS, EGPRS 44
infrared 43
picture messages 28, 33
PIN codes 9, 15
plug and play service 15
postcards 29
messages 32
my shortcuts 41
phone 47
profiles 39
power
key 17
saver 40
restore factory settings 49
security 49
predictive text input 27
profiles 39
service inbox 73
themes 39
PUK codes 9
pushed messages 73
time 40
tones 39
USB data cable 45
wallpaper 40
R
radio 57
shared memory 8
shortcuts 41
recorder 58
restriction password 9
ringing tones 39
signal strength 18
SIM
card 21
card installation 12
messages 32
S
safety information 6, 83
SAR 85
services 69
SMS. See text messages
software updates 47, 50
speakerphone. See loudspeaker.
standby mode 18, 41
status indicators 18
stereo widening 59
stopwatch 62
screen saver 40
scroll key 17
scrolling 25
security
codes 9
module 74
settings 49
selection keys 17
service
strap 16
streaming service 55
switch on and off 14
swivel 40
commands 31
inbox 73
messages 73
numbers 36
services 70
settings
synchronization 44
T
take an image 54
text
active standby 40
call 46
clock 40
configuration 48
connectivity 42
data transfer 44
date 40
display 40
downloads 73
message 26
phone 48
themes 39
time settings 40
to-do list 61
tones 39
traditional text input 27
90
volume
adjusting 22, 56, 57
key 17
U
unlock keypad 20
UPIN 15
USB 17
W
wallpaper 40
V
web 70
vehicles 84
video clip 54
visual radio 58
voice
wireless markup language 70
wrist strap 16
X
commands 41
dialing 22
messages 31
recorder 58
XHTML 70
91
|