MODEL : DVD-19
OWNER’S MANUAL
Before operating the unit, please read this manual
carefully and completely, and retain it for future reference.
NOTE : THE DESIGNS & SPECIFICATIONS ARE SUBJECT
TO CHANGE WITHOUT NOTICE FOR IMPROVEMENT
INTRODUCTION
Safety Instructions
The lightning flash with arrowhead symbol,
within ane quilateral triangle, is intended to
alert the user to the presence of uninsulated
“dangerous voltage” within the product’s
enclosure that may be of sufficient magnitude
to constitute a risk of electric shock to persons.
WARNING
RISK OF ELECTRIC
SHOCK DO NOT OPEN
WARNING : TO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE COVER(OR BACK). NO
USER SERVICEABLE PARTS INSIDE. REFER
SERVICING TO QUALIFIED SERVICE PERSONNEL.
The exclamation point within an equilateral
triangle is intended to alert the user to the
presence of important operating and
maintenance (servicing) instructions in the
literature accompanying the appliance.
WARNING : TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO
RAIN OR MOISTURE.
CAUTION : TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.
CAUTION : This Digital Video Disc Player employs a Laser System. To ensure proper use of this product, please read
this owner’ s manual carefully and retain for future reference, should the unit require maintenance, contact
an authorized service location-see service procedure.
Use of controls, adjustments or the performance of procedures other than those specified may result herein
hazardous radiation exposure.
To prevent direct exposure to laser beam, do not try to open the enclosure. Visible laser radiation when
open the enclosure. DO NOT STARE INTO BEAM.
1. Read owner’s manual
7. Accessories
After unpacking this product, read the owner’s
manual carefully and follow all the operating and
other instructions.
Any mounting of the product should follow the
manufacturer’s instructions, and should use a
mounting accessory recommended by the
manufacturer. Quick stops, excessive force, and
uneven surfaces may cause the product and cart
combination to overturn.
2. Power Sources
This product should be operated from DC12V of
battery
8. Disc Tray
3. Heat
Keep your fingers well clear of the disc tray as it is
closing. It may cause serious personal injury.
The product should be situated away from heat
sources (including amplifiers) that produce heat.
During storms, or when it is left unattended and
unused for long periods of time, unplug it from the
wall outlet. This will prevent damage to the product
due to lightning and power-line surges.
9. Burden
Do not place a heavy object on or step on the
product. The object may fall, causing serious
personal injury and serious damage to the product.
4. Keep drinks and cleaning solutions away from the
body of the DVD.
10. Laser Beam
Do not look into the opening of the disc tray or
ventilation opening of the product to see the source
of the laser beam. It may cause sight damage.
5. Object and Liquid Entry
Never push objects of any kind into this product
through openings as they may touch dangerous
voltage points or short-out parts that could result in
a fire or electric shock. Never spill liquid of any kind
on the product.
11. Disc
Do not use a cracked, deformed, or repaired disc.
These discs are easily broken and may cause serious
personal injury and product malfunction.
6. Attachments
Do not use attachments not recommended by the
product manufacturer as they may cause hazards.
-3-
INTRODUCTION
Safety Instructions
12. Damage Requiring Service
a) When the power-supply cord is damaged.
b) If liquid has been spilled, or objects have fallen
into the product.
14. Replacement parts
When replacement parts are required, be sure the
service technician has used replacement parts
specified by the manufacturer or have the same
characteristics as the original part. Unauthorized
substitutions may result in fire, electric shock, or
other hazards.
c) If the product has been exposed to rain or water.
d) If the product does not operate normally by
following the operating instructions. Adjust only
those controls that are covered by the operating
instructions as an improper adjustment of other
controls may result in damage and will often
require extensive work by a qualified technician
to restore the product to its normal operation.
e) If the product has been dropped or damaged in
any way.
15. Safety Check
Upon completion of any service or repairs to this
product, ask the service technician to perform safety
checks to determine that the product is in proper
operating condition.
f) When the product exhibits a distinct change in
performance-this indicates a need for service.
13. Servicing
Do not attempt to service this product yourself as
opening or removing covers may expose you to
dangerous voltage or other hazards. Refer all
servicing to qualified service personnel.
Note on Region Numbers
The region number is allocated to machine and software according to where they are sold.
DVDs can be played on this machine if their region number is the same or includes the same number, or if
the DVD is marked “ALL”.
Confirm the region number for this machine before choosing discs. The number for machine is indicated
on the rear panel.
Notes on Copyrights
It is forbidden by law to copy, broadcast, show, broadcast on cable, play in public, and rent copyrighted
material without permission.
-4-
INTRODUCTION
Front Panel
POWER button
DISC tray
EJECT button
PLAY/PAUSE
button
Remote sensor
STOP button
Rear Panel
AUDIO IN
jacks
VIDEO IN
jack
DC 12V
INPUT jack
REMOTE INPUT
jack
AUDIO OUT VIDEO OUT
jacks jack
DC 12V
OUTPUT jack
Coaxial DIGITAL
AUDIO OUT jack
-5-
INTRODUCTION
Remote Control
NTSC/PAL button
Open/Close button
SETUP button
Open/Close
POWER
SETUP
NTSL/PAL
POWER button
FUNCTION
ANGLE
FUNCTION button
ANGLE button
AUDIO button
1
4
7
2
5
8
0
-
3
6
NUMERIC buttons
AUDIO
9
SUBTITLE
CLEAR
SUBTITLE button
PROGRAM button
CLEAR button
PROGRAM
-
KEY
+
VOL
+
VOLUME +/ button
-
KEY CONTROL +/ button
-
PAUSE
SEARCH
PAUSE button
ARROW buttons
PLAY button
SEARCH button
ENTER button
ENTER
PLAY
STOP
STOP button
SCAN button
MENU button
SKIP button
STEP button
MENU
L/R/ST
PBC
TITLE
MUTE
SLOW
ZOOM
A-B
STEP
TITLE button
L/R/STEREO button
MUTE button
SLOW button
DISPLAY
REPEAT
DISPLAY button
ZOOM button
RETURN
PBC button
REPEAT button
RETURN button
REPEAT A-B button
-6-
INTRODUCTION
Using the Remote Control
Inserting Batteries
When operating the remote control, point it at
the remote control sensor as shown on the
diagram.
The remote control can be used from a direct
distance of approximately 4~5 meters.
The remote control can be operated at a
horizontal angle of up to 25 degree with
respect to the remote control sensor.
1
Open the battery cover.
2
3
Insert batteries(AAA size).
Make sure to match the + and
batteries to the marks inside the battery
compartment.
-
on the
Close the cover.
1
2
3
Within 4~5m
POWER
Open/Close
SETUP
NTSL/PAL
FUNCTION
ANGLE
1
4
7
2
5
8
0
3
6
9
AUDIO
SUBTITLE
C
LEAR
PROGRAM
+
-
KEY
-
VOL
+
PAUSE
SEARCH
ENTER
PLAY
STOP
MENU
L/R/ST
PBC
TITLE
MUTE
SLOW
ZOOM
A-B
STEP
DISPLA
Y
RETURN
REPEAT
Notes
Improper use of batteries may cause battery leakage and corrosion.
Do not insert the batteries into the remote control in the wrong direction.
If you do not use the remote control for a long period of time, remove the batteries to avoid possible
damage from battery corrosion.
If the remote control does not function correctly or if the operating range becomes reduced, replace all
batteries with new ones.
If battery leakage occurs, wipe the battery liquid from the battery compartment, then insert new
batteries.
Do not drop or give the remote control a shock.
Do not leave the remote control near extremely hot or humid place.
Do not spill water or put anything wet on the remote control.
-7-
CONNECTIONS
Connection to a TV
You can connect the player to your TV.
Video cable
To Video Output
To Audio
Input
To Video
Input
Audio cable
TFT WIDE COLOR MONITOR
To Audio Output(R/L)
TV or monitor with
Audio/Video Inputs
Notes
Refer to the owner's manual of your TV as well.
When you connect the player to your TV, be sure to turn off the power and unplug both units before
making any connections.
Connect the player to your TV directly. If you connect the player to a VCR, the playback picture will be
distorted because video discs are copy protected.
-8-
CONNECTIONS
Connection to an Audio System
You can connect the player to your audio system and TV.
To Video Output
To Audio Input
Audio cable
To Audio Output(R/L)
Audio System
TFT WIDE COLOR MONITOR
Video cable
To Video Input
TV or monitor with
Audio/Video Inputs
Notes
Refer to the owner's manual of your car audio system as well.
When you connect the player to other equipment, be sure to turn off the power and unplug all of the
equipment before making any connections.
If you place the player near a tuner or radio, the radio broadcast sound might be distorted. In this case,
move the player away from the tuner and radio.
The output sound of the player has a wide dynamic range. Be sure to adjust the receiver’s volume to
a moderate listening level. Otherwise, the speakers may be damaged by sudden high volume sound.
Turn off the receiver before you connect or disconnect the player’s power cord. If you leave the
receiver the power on, the speakers may be damaged.
-9-
CONNECTIONS
Connection to Optional Audio System
Dolby Digital Sound
You can enjoy the high quality dynamic sound of Dolby Digital, Dolby Pro Logic, and 2 Channel Digital
Stereo.
Dolby Digital
Dolby Digital is the surround sound technology used in theaters showing the latest movies, and is now
available to reproduce this realistic effect in the car and home. You can enjoy motion picture and live
concert DVD video discs with this dynamic realistic sound by connecting the DVD player to a 6 channel
receiver equipped with a Dolby Digital decoder or Dolby Digital processor.
Video cable
TFT WIDE COLOR MONITOR
Coaxial cable
Center
speaker
Front
Front
speaker(L)
speaker(R)
To enjoy Dolby Digital sound
from this DVD player you need the
following:
(1) DVD video discs recorded in
Dolby Digital
(2) A 5.1-channel receiver equipped
with multi-channel speaker outputs
and a Dolby Digital decoder.
(3) 5 speakers and 1 sub woofer
Rear
Rear
speaker(L)
speaker(R)
Sub
woofer
Manufactured under license from Dolby
Laboratories. “Dolby”, “ Pro Logic” and
the double-D symbol are trademarks of
Dolby Laboratories.
Confidential unpublished works.
1992-1997 Dolby Laboratories, Inc.
All rights reserved.
Receiver equipped with
Dolby Digital decoder
-10-
CONNECTIONS
Connection to Optional Audio System
Dolby Surround Sound
Dolby Surround
You can still enjoy the excitement of Surround Sound even if your A/V receiver does not offer Dolby Digital
decoding. If your A/V receiver has a Dolby Surround decoder. Refer to the following connection diagram.
Audio cable
TFT WIDE COLOR MONITOR
Video cable
TV
Center
speaker
Front
Front
speaker(L)
speaker(R)
Connect one or two rear speakers.
The output sound from the rear
speakers will be monaural even if
you connect two rear speakers.
Rear
Rear
speaker(L)
speaker(R)
Sub
woofer
With a receiver equipped with Dolby Digital
Refer to that receiver’s owner’s manual and set
the receiver so you can enjoy Dolby Surround
Sound.
Receiver equipped
with Dolby surround decoder
-11-
BASIC OPERATION
Basic Playback
Preparations
When you want to playback DVD video discs, turn on the TV and select the video input source
connected to the player.
When you want to enjoy the sound of DVD video discs or audio CDs from the audio system, turn on
the audio system and select the input source connected to the player.
For connection details, see pages 8 through 11.
Set the playback picture size according to the aspect ratio of the connected TV.
1
2
Press POWER button.
The player turns on.
Open/Close
POWER
SETUP
NTSL/PAL
FUNCTION
ANGLE
Press OPEN/CLOSE button.
-The disc tray opens.
-You can open the disc tray by pressing this
button even if the player is playback mode.
1
4
7
2
5
8
0
-
3
6
AUDIO
9
SUBTITLE
CLEAR
PROGRAM
+
-
KEY
VOL
+
3
Place a disc on the disc tray with the playback
side down.
PAUSE
SEARCH
-There are two different disc sizes. Place the
disc in the correct guide on the disc tray. If
the disc is out of the guide, it may damage
the disc and cause the player to malfunction.
ENTER
PLAY
STOP
MENU
L/R/ST
PBC
TITLE
MUTE
SLOW
ZOOM
A-B
STEP
-Do not place anything except 3 (inches) discs
DISPLAY
REPEAT
"
RETURN
or 5 discs on the disc tray.
"
4
Press OPEN/CLOSE button to close the
loading drawer.
The player will begin playback automatically
for all of the discs.
When a menu screen appears on the TV
screen.
In case of interactive DVDs with control, a
menu screen appears on the TV screen.
Perform step as below.
5
Press
and press PLAY(ENTER)
button, or press the numeric button(s) to select
the desired item on the menu.
1
2
3
4
Example of interactive DVD On-screen Menu
For further information refer to the jacket or
case of the disc you are playing.
A note about Power off function
This player is equipped with the Aux function.
If the player is powered off, it will be automatically
switched to Aux.
Notes
When “ ” appears on the TV screen while
a button is pressed it means that this
function is not available on the disc you are
playing.
Depending on the DVD disc, some operations
may be different or restricted. Refer to the
jacket or case of the disc you are playing.
-12-
BASIC OPERATION
Basic Playback
Still Picture(Pause)
Press PAUSE button during playback.
DVD : The player will be placed in the still picture mode.
CD : The player will be placed in the pause mode.
Open/Close
POWER
SETUP
NTSL/PAL
To return to normal playback, press PLAY or PAUSE
button.
FUNCTION
ANGLE
1
4
7
2
5
8
0
-
3
6
AUDIO
Notes
9
SUBTITLE
CLEAR
Some discs may not respond to still picture.
Depending on the DVD disc, still picture operation may
be different or restricted.
PROGRAM
+
-
KEY
VOL
+
PAUSE
SEARCH
PAUSE
PLAY
ENTER
PLAY
STOP
STOP
SKIP
(PREVIOUS, NEXT)
Skipping Forward or Backward
Skipping Forward
MENU
L/R/ST
PBC
TITLE
MUTE
SLOW
ZOOM
A-B
STEP
DISPLAY
REPEAT
SLOW
Press SKIP
button during playback.
RETURN
A chapter (DVD) or a track (CD) is skipped each time the
button is pressed.
Skipping Backward
Press SKIP
button during playback.
A chapter (DVD) or a track (CD) is skipped backward, each
time the button is pressed, if the time is less than 2 seconds.
Otherwise, you can go to the start point of the chapter / track.
Slow Playback
Stopping Playback
When playing DVDs
Press STOP button during playback.
Press SLOW button to see variable-speed slow picture
during playback.
To return to normal playback, press PLAY button.
-
-
-
The player is in RESUME STOP mode and the stop
position is stored in memory.
If you press PLAY button, playback resumes from the
position at which it was stopped.
If you press the stop button once again the unit will cease
playing the DVD but the memory will be maintained for
12 hours.
In case of DVD:
SF 2×→SF 4×→SF 8×→Release
(1/2 x speed forward slow screen)
(Normal play)
-
During playback if you press the MENU button the player
enters to the menu selection mode and the player is in
resume stop mode and the stop position is stored in
memory.
Notes
Some discs may not respond to slow playback.
Depending on the DVD disc, slow playback
operation may be different or restricted.
And you can control the menu operating.
-13-
BASIC OPERATION
Basic Playback
High speed Playback
When playing DVD discs
Press SCAN( ) button to see high speed
picture during playback or pause.
- By pressing forward SCAN( ) button or backward
) button, you can see variable speed picture.
,
Open/Close
POWER
SETUP
NTSL/PAL
NTSC/PAL
VOLUME
FUNCTION
ANGLE
SCAN(
1
4
7
2
5
8
0
-
3
6
FUNCTION
- To return to normal playback, press PLAY button.
AUDIO
9
SUBTITLE
FF 2×→FF 4×→FF 8×→FF 16×→FF 32×→FF 64×→Release
CLEAR
(2 X Search)
(Normal play)
PROGRAM
+
-
KEY
VOL
+
FR 2×→FR 4×→FR 8×→FR 16×→FR 32×→FR 64×→Release
KEY
PAUSE
SEARCH
(2 X Backward search)
FF:Fast Forward FR:Fast Reverse
(Normal play)
ENTER
ENTER
When playing an ordinary audio CD
PLAY
STOP
It plays by fast forward or fast backward speed at ×2,
×4 and ×6 .
SCAN
MUTE
MENU
L/R/ST
PBC
TITLE
MUTE
SLOW
ZOOM
A-B
STEP
STEP
FF 1×→FF 2×→FF 4×→FF 6×→Release
DISPLAY
REPEAT
(2 X Search)
(Normal play)
RETURN
FR 1×→FR 2×→FR 4×→FR 6×→Release
(2 X Backward search)
(Normal play)
One Step Playback
When playing DVD discs
Press STEP button the player will enter step playing.
- Each time you press STEP button, the picture advances
one frame.
- To return to normal playback, press PLAY(or PAUSE)
button.
Selecting TV Systems
Press NTSC/PAL button and ENTER button on
the remote control to set your TV color system
during stop or resume stop mode.
Volume Control
If your TV is NTSC color system, select NTSC.
If your TV is PAL color system, select PAL.
If you select MULTI, TV color system is subject to
the disc you play.
Press VOLUME + button on the remote control to
increase the volume of the player.
Press VOLUME
-
button on the remote control to
decrease the volume of the player.
Notes
The TV system setting must be coincided with
the connected TV color system.
Under the condition that the NTSC color
system TV is connected, if you play a PAL
color disc and you cannot see the regular
pictures.
Key Control(Audio CD)
If this player is selected Karaoke mode on the
setup menu, then you can enjoy the Karaoke play.
During Karaoke mode you can control the key by
+
using the KEY
/
-
buttons on the remote control.
Sound Mute
To Convert Function Selection
Press the MUTE button to mute the sound of the
player.
To cancel the mute function, press the MUTE button
1. Press POWER button to turn on the player.
2. Press FUNCTION button to select the A/V-OUT
you want. A/V-OUT will be switched and selected
whenever you press the button.
again or press the VOL +/
-
button.
If the volume level is zero, you cannot hear any sound.
(AUX IN → DVD → AUX IN...)
3. If you are in power off, the function is switched to
the AUX IN.
-14-
ADVANCED OPERATION
Zoom feature
Press ZOOM button during normal playback or
Open/Close
POWER
SETUP
NTSL/PAL
still playback.
The Zoom feature allows to enlarge the picture on
the screen.
FUNCTION
ANGLE
1
4
7
2
5
8
0
3
6
ANGLE
AUDIO
9
SUBTITLE
CLEAR
1.5
3
PROGRAM
+
-
KEY
-
VOL
+
PAUSE
SEARCH
ENTER
Each time you press
point shifts.
buttons, the zoom
PLAY
STOP
MENU
L/R/ST
PBC
TITLE
MUTE
SLOW
ZOOM
A-B
STEP
ZOOM
DISPLAY
DISPLAY
REPEAT
Note
RETURN
Some discs may not respond to zoom feature.
Depending on the DVD disc, zoom operation
may be different or restricted.
Viewing from another angle
Some DVDs may contain scenes which have been
shot simultaneously from a number of different
angles.
For these discs, the same scene can be viewed
from each of these different angles using the
ANGLE button.(The recorded angles differ
depending on the disc used.)
1
Press ANGLE button during playback if you
can use angle mark.
-The next angle number is displayed.
2
Press ANGLE button repeatedly until the
desired angle is selected.
Note
This ANGLE function works only for discs
having scenes recorded at a different angles.
L/R/Stereo Function(Audio-CD)
Using L/R/ST function, the Left-mono. Right-mono
or Stereo can be selected and played. And use it
when playing a disc with Sound Multiplex logo.
According to the selection of L/R/Stereo function,
the sound will be output from the front Right of the
front Left channel as the following table:
Output
L-channel
R-channel
Button select
L-CH signal
on the disc
R-CH signal
on the disc
STEREO
R-CH signal
on the disc
R-CH signal
on the disc
RIGHT
LEFT
L-CH signal
on the disc
L-CH signal
on the disc
-15-
ADVANCED OPERATION
Program playback (
)
Audio-CD
Program playback lets to set up a specific order for playback of tracks on a disc.
1
2
Press the PROGRAM button during stop mode.
Press the NUMERIC buttons as you want.
3
4
To start the program play, press the PLAY button.
To cancel the play, press the STOP button and the PROGRAM button twice.
Repeat playback
You can playback chapter, title,or tracks repeatedly.
Set this function during playback.
Setting the Repeat A-B playback
1. Press A-B button during play at the point
where repeat play is to start(A)
PRESET : Press REPEAT button when title,
chapter, folder or song for repetition is played.
Repetition play mode changes as shown
below whenever you press this button and
relevant mode appears in TV screen.
2. Press A-B during play at the point where
repeat play is to be concluded(B)
3. To cancel it press A-B button again.
In case of DVD:
: Chapter Repetition Play Mode
Notes
: Title Repetition Play Mode
Repeat play works only with discs for which
the elapsed playing time appears in the DVD
display window during playback.
: Release(Normal Play)
(“REPEAT” is off)
Repeat play may not works correctly with
some DVDs.
If the time from A to B is less than 3 seconds,
the player repeats about 3 seconds.
In case of CD:
: Song repetition mode
Repeat A-B play works only within a title DVD
: Disc Repetition Play Mode
or a track CD.
Some subtitles recorded around point A or B
may fail to appear (DVD).
: Release (Normal play)
(“REPEAT” is off)
During repeat playback, if you need to play a
certain track and you can select the track by
using the NUMERIC or SKIP buttons.
Depending on the discs, this function may be
different.
To release Repetition Play Mode and start
normal play, repetitively press REPEAT button
until “REPEAT OFF” is displayed in TV screen.
-16-
ADVANCED OPERATION
Open/Close
POWER
SETUP
NTSL/PAL
1
Press TITLE button in stop or playback
mode.
FUNCTION
ANGLE
1
4
7
2
5
8
0
-
3
6
AUDIO
A list of titles on the disc is displayed.
Press TITLE again to resume play from the
scene when TITLE was first pressed.
Resume play may not be possible on certain
discs.
9
SUBTITLE
CLEAR
PROGRAM
+
-
KEY
VOL
+
PAUSE
SEARCH
SEARCH
ENTER
PLAY
ENTER
PLAY
STOP
2
Press
buttons and press PLAY
MENU
TITLE
MENU
L/R/ST
PBC
TITLE
MUTE
SLOW
ZOOM
A-B
STEP
(ENTER) button.(Or press the numeric
button to select a desired title)
DISPLAY
REPEAT
RETURN
The selected title now starts playing.
Using a DVD menu(DVD)
Some DVDs has unique menu structures called
DVD menus For example, DVDs programmed with
complex contents provide guide menus, and those
recorded with various languages provide menus
for audio and subtitle language. Although the DVD
menu's contents and operation differ from disc to
disc, the following explains the basic operation
when this feature is used.
Search function
When playing DVD
Search function allows you to start playing at any
chosen time or chapter number or title number.
1
2
Press the SEARCH button and repeatedly
until you reach your desired menu screen.
Press
buttons to select the desired
item and press NUMERIC button to enter
the required chapter number, title number.
Or input the NUMERIC buttons to search a time.
At this time, if you want to cancel the number
or time, press the CLEAR button on the
remote.
Example
3
Press ENTER button to confirm it.
When playing audio CD
Search function allows you to start playing at any
chosen time of the track.
1
2
Press MENU button during playback or
stop.
The DVD menu available on the disc is now
displayed.
1
2
Press SEARCH button.
Press NUMERIC buttons to search a time.
For searching a track, press NUMERIC
buttons and ENTER button.
If you want to cancel, press the CLEAR button.
Press
buttons and press PLAY
(ENTER) button.
(Or press the numeric button(s) to select a
desired item)
Using a title menu(DVD)
The selected item is now executed.
Some movie discs may contain two or more titles.
If the disc has a title menu recorded on it, the
TITLE button can be used to select the movie title.
(The operation may differ depending on the disc used.)
3
To resume play from the scene before you
press the MENU button, press the MENU
button again.
Example
-17-
ADVANCED OPERATION
Changing audio language(DVD)
It is possible to change the audio language to a
different language from the one selected at the
initial settings.
This operation works olny with discs on which
multiple audio languages are recorded.
Open/Close
POWER
SETUP
NTSL/PAL
FUNCTION
ANGLE
1
4
7
2
5
8
0
-
3
6
AUDIO
9
AUDIO
SUBTITLE
SUBTITLE
CLEAR
PROGRAM
+
Press AUDIO button repeatedly to select the
desired audio language.
-
KEY
VOL
+
PAUSE
SEARCH
ENTER
Note
PLAY
STOP
When the desired audio language is not selected
even after pressing the button several times, it
means that the language is not available on the
disc.
MENU
L/R/ST
PBC
TITLE
MUTE
SLOW
ZOOM
A-B
STEP
DISPLAY
REPEAT
RETURN
Changing subtitle language(DVD)
It is possible to change the subtitle language to a
different language from the one selected at the
initial settings. This operation works olny with
discs on which multiple subtitle languages are
recorded.
Press SUBTITLE button repeatedly during
playback to select the desired subtitle
language.
Note
When the desired subtitle language is not selected
even after pressing the button several times, it
means that the language is not available on the
disc.
-18-
INITIAL SETUP OPERATION
Main Page
If pressing "SETUP Button" on the remote control,
you can see the followings on the TV screen.
Open/Close
POWER
SETUP
Button
SETUP
NTSL/PAL
SETUP MENU - - MAIN PAGE
GENERAL SETUP
SPEAKER SETUP
AUDIO SETUP
FUNCTION
ANGLE
1
4
7
2
5
8
0
3
6
KARAOKE SETUP
PREFERENCES
AUDIO
9
SUBTITLE
CLEAR
EXIT SETUP
PROGRAM
GENERAL SETUP
You can set up such general functions as TV
Display, Angle Mark, OSD Language, Captions and
Screen Saver.
SETUP MENU - - MAIN PAGE
GENERAL SETUP
SPEAKER SETUP
AUDIO SETUP
You can adjust the number of output channels in
accordance with that of output speakers.
KARAOKE SETUP
PREFERENCES
You can set up SPDIF, Dual Mono and Dynamic.
You can set up Karaoke ON/OFF.
EXIT SETUP
You can set up TV Type, Audio, Subtitle, Disc Menu,
Locality code, Parental Control, Password setup
and so forth.
GENERAL SETUP
After setting up , you can exit from the setup menu.
How to Setup
If using "Arrow Buttons" on the remote control as
shown in the main page, you can scroll where you
PROGRAM
want.
-
KEY
+
-
VOL
+
SETUP MENU - - MAIN PAGE
PAUSE
SEARCH
GENERAL SETUP
SPEAKER SETUP
AUDIO SETUP
Arrow
Buttons
ENTER
KARAOKE SETUP
PREFERENCES
PLAY
STOP
EXIT SETUP
MENU
TITLE
SLOW
STEP
GENERAL SETUP
If pressing "ENTER Button" at the menu that you
have selected, you can see the following selection
menu.
CLEAR
0
PROGRAM
+
SETUP MENU - - MAIN PAGE
-
KEY
-
VOL
+
PAUSE
SEARCH
GENERAL SETUP
SPEAKER SETUP
AUDIO SETUP
ENTER
Button
ENTER
KARAOKE SETUP
PREFERENCES
PLAY
STOP
EXIT SETUP
MENU
TITLE
SLOW
STEP
GENERAL SETUP
-19-
INITIAL SETUP OPERATION
How to Setup
If using "Arrow Buttons" at the menu you want to set
up, you can scroll to sub-items.
KEY
+
VOL
+
- - GENERAL PAGE - -
PAUSE
SEARCH
TV DISPLAY
ANGLE MARK
OSD LANG
CAPTIONS
NORMAL / PS
NORMAL / LB
WIDE
Arrow
Buttons
ENTER
PLAY
STOP
SCR SAVER
MAIN PAGE
MENU
L/R/ST
TITLE
MUTE
SLOW
ZOOM
STEP
DISPLAY
NOMAL TV PAN SCAN
If using "Arrow Buttons" on the remote control, you
can scroll where you want.
PROGRAM
+
- - GENERAL PAGE - -
-
KEY
-
VOL
+
PAUSE
SEARCH
TV DISPLAY
ANGLE MARK
OSD LANG
CAPTIONS
NORMAL / PS
NORMAL / LB
WIDE
Arrow
Buttons
ENTER
SCR SAVER
PLAY
STOP
MAIN PAGE
MENU
TITLE
SLOW
STEP
WIDE SCREEN TV
You can select using "ENTER Button" on the
remote control.
CLEAR
0
- - GENERAL PAGE - -
PROGRAM
+
-
KEY
-
VOL
+
TV DISPLAY
ANGLE MARK
OSD LANG
CAPTIONS
NORMAL / PS
NORMAL / LB
WIDE
PAUSE
SEARCH
ENTER
Button
ENTER
SCR SAVER
PLAY
STOP
MAIN PAGE
MENU
TITLE
SLOW
STEP
WIDE SCREEN TV
You can back to the upper menu using "Arrow
Buttons" on the remote control, or finish setting up
pressing "SETUP Button".
0
PROGRAM
+
-
KEY
-
VOL
+
- - GENERAL PAGE - -
PAUSE
SEARCH
TV DISPLAY
ANGLE MARK
OSD LANG
CAPTIONS
NORMAL / PS
NORMAL / LB
WIDE
Arrow
Buttons
ENTER
PLAY
STOP
SCR SAVER
MAIN PAGE
MENU
TITLE
SLOW
STEP
SET DISPLAY MODE
-20-
INITIAL SETUP OPERATION
General Setup
You can scroll to the "General Setup" menu using
"Arrow Buttons" on the remote control as shown in
the main page.
PROGRAM
-
KEY
+
-
VOL
+
SETUP MENU - - MAIN PAGE
PAUSE
SEARCH
GENERAL SETUP
SPEAKER SETUP
AUDIO SETUP
Arrow
Buttons
ENTER
KARAOKE SETUP
PREFERENCES
PLAY
STOP
EXIT SETUP
MENU
TITLE
SLOW
STEP
GENERAL SETUP
If pressing "ENTER Button" on the remote control at
the "General Setup" menu, you can see the
following sub-selection menu.
CLEAR
0
PROGRAM
+
- - GENERAL PAGE - -
-
KEY
-
VOL
+
PAUSE
SEARCH
TV DISPLAY
ANGLE MARK
OSD LANG
CAPTIONS
NORMAL / PS
NORMAL / LB
WIDE
ENTER
Button
ENTER
SCR SAVER
PLAY
STOP
MAIN PAGE
MENU
TITLE
SLOW
STEP
GENERAL SETUP
Setting for TV Display
- - GENERAL PAGE - -
However, if the disc is designed to provide video in the
ratio of 4:3, the following setup enables you to enjoy a
wide screen.
TV DISPLAY
NORMAL / PS
NORMAL / LB
WIDE
ANGLE MARK
OSD LANG
CAPTIONS
SCR SAVER
MAIN PAGE
SET TV DISPLAY MODE
NORMAL/PS
NORMAL/LB
WIDE
Normal TV Pan Scan - You can
select this mode where you can
enjoy the screen in the ratio of 4:3
on TV with 4:3, or the screen of 16:9
expanded to be matched with 4:3.
Normal TV Letter Box - You can
select this mode where you can
enjoy the screen in the ratio of 16:9
on TV with 4:3, but you will see a
black band on the upper and lower
screen.
Wide Screen TV - If your TV is in
the ratio of 16:9, you can select this
mode.
-21-
INITIAL SETUP OPERATION
General Setup
Setting for Angle Mark
ON
- - GENERAL PAGE - -
TURN ANGLE MARK ON
TV DISPLAY
ANGLE MARK
OSD LANG
CAPTIONS
ON
OFF
SCR SAVER
MAIN PAGE
OFF
TURN ANGLE MARK OFF
ANGEL MARK ON/OFF
Setting for Angle Mark is available only if the disc contains the multi-angled scenes.
Setting for OSD Language
- - GENERAL PAGE - -
TV DISPLAY
ANGLE MARK
ENGLISH
SET OSD LANGUAGE TO THE ONE YOU WANT.
OSD LANG
CAPTIONS
SCR SAVER
ENGLISH
MAIN PAGE
SET OSD LANGUAGE TO ENGLISH
Set OSD language to the one which you want.
-22-
INITIAL SETUP OPERATION
General Setup
Setting for Captions
ON
- - GENERAL PAGE - -
CLOSED CAPTION ON
TV DISPLAY
ANGLE MARK
OSD LANG
CAPTIONS
ON
SCR SAVER
OFF
OFF
MAIN PAGE
CLOSED CAPTIONS OFF
CLOSED CAPTION
Setting for Screen Saver
- - GENERAL PAGE - -
TV DISPLAY
ANGLE MARK
OSD LANG
CAPTIONS
ON
SCREEN SAVER ON - Turn Screen Saver on.
SCR SAVER
ON
OFF
OFF
MAIN PAGE
SCREEN SAVER OFF - Turn Screen Saver off.
SCREEN SAVER
The function "Screen Saver" darkens the screen on which the SPOT moves around if DVD is not
used for a long time.
-23-
INITIAL SETUP OPERATION
Speaker Setup
You can scroll to the "Speaker Setup" menu using
"Arrow Buttons" on the remote control as shown in
the main page.
PROGRAM
-
KEY
+
-
VOL
+
SETUP MENU - - MAIN PAGE
PAUSE
SEARCH
GENERAL SETUP
SPEAKER SETUP
AUDIO SETUP
Arrow
Buttons
ENTER
KARAOKE SETUP
PREFERENCES
PLAY
STOP
EXIT SETUP
MENU
TITLE
SLOW
STEP
GOTO SPEAKER SETUP PAGE
You can see the followings if pressing "ENTER
Button" on the remote control at the "Speaker
Setup" menu.
PROGRAM
+
- - SPEAKER SETUP PAGE - -
-
KEY
-
VOL
+
PAUSE
SEARCH
DOWN MIX
LT / RT
STEREO
MAIN PAGE
ENTER
Button
ENTER
PLAY
STOP
MENU
TITLE
SLOW
STEP
LOUD SPEAKERS SETUP
Setting for DownMix
LT/RT
- - SPEAKER SETUP PAGE - -
SET LT/RT DOWNMIX - Only if you want to hear
the speaker sounds of front left/right of the original,
by two channel, you select "LT/RT” downmix.
DOWN MIX
LT / RT
STEREO
MAIN PAGE
STEREO
SET STEREO DOWNMIX - If you want to hear the
all speaker sounds of the original, by two channel,
you select “STEREO” downmix.
SETUP DOWNMIX MODE
"DOWNMIX" optimizes the number of the output channel suitable for that of the speaker.
-24-
INITIAL SETUP OPERATION
Audio Setup
You can scroll to the "Audio Setup" menu using
"Arrow Buttons" on the remote control as shown in
the main page.
PROGRAM
-
KEY
+
-
VOL
+
SETUP MENU - - MAIN PAGE
PAUSE
SEARCH
GENERAL SETUP
SPEAKER SETUP
AUDIO SETUP
Arrow
Buttons
ENTER
KARAOKE SETUP
PREFERENCES
PLAY
STOP
EXIT SETUP
MENU
TITLE
SLOW
STEP
GOTO DOLBY DIGITAL SETUP PAGE
You can see the followings if pressing "ENTER
Button" on the remote control at the "Audio Setup"
menu.
CLEAR
0
- - AUDIO SETUP - -
PROGRAM
+
-
KEY
-
VOL
+
SPDIF
ON
PAUSE
SEARCH
DUAL MONO
DYNAMIC
OFF
ENTER
Button
ENTER
MAIN PAGE
PLAY
STOP
MENU
TITLE
SLOW
STEP
SELECT SPDIF
Setting for SPDIF
- - AUDIO SETUP - -
OFF
OFF
SPDIF
DIGITAL AUDIO OUT OFF
DUAL MONO
DYNAMIC
ON
ON
MAIN PAGE
DIGITAL AUDIO OUT ON
SELECT SPDIF
If you don’t select “ON”, you cannot hear any sound through Digital output.
-25-
INITIAL SETUP OPERATION
Audio Setup
Setting for Dual Mono
STEREO
- - AUDIO SETUP - -
SPDIF
SET STEREO MODE
DUAL MONO
DYNAMIC
STEREO
L-MONO
R-MONO
MIX-MONO
L-MONO
MAIN PAGE
SET LEFT MONO MODE
R-MONO
SET RIGHT MONO MODE
DUAL MONO (1+1) SETUP
MIX-MONO
SET MIXED MONO MODE
"DUAL MONO" as is the mode for multi-sound broadcasting enables you to hear the sound from
one set of speakers output also from the other set.
Setting for Dynamic
DYNAMIC
- - AUDIO SETUP - -
An adjustment passes through 8 levels from 1/8
to 8/8(FULL) and OFF.
SPDIF
6 / 8
DUAL MONO
DYNAMIC
4 / 8
2 / 8
MAIN PAGE
OFF
DYNAMIC RNG COMPRESSION OFF
"Dynamic Range" refers to the range of a change in sound volume (dB) between its maximum value
and its minimum value with a specific media given.
-26-
INITIAL SETUP OPERATION
Karaoke Setup
- - KARAOKE SETUP - -
OFF
KARAOKE MODE
OFF
KARAOKE MODE OFF
KARAOKE
KARAOKE
MAIN PAGE
KARAOKE MODE ON
-27-
INITIAL SETUP OPERATION
Preferences
If the disc doesn't support "PREFERENCES", you
can't set it up. For example, when you play some disc.
- - PREFERENCES PAGE - -
TV TYPE
AUDIO
SUBTITLE
DISC MENU
LOCALE
"LOCALITY CODE" refers to allocating each
locality code per all the players and the DVD titles
with the world divided into 6 zones.
PARENTAL
PASSWORD
DEFAULTS
SET PREFERENCES
TV TYPE
AUDIO
PREFERED TV SIGNAL - You can select among
the follwing TV signal :
PREFERED AUDIO LANGUAGE
Multi Sync TV - You can use this mode if your TV
supports both NTSC and PAL.
NTSC TV - NTSC TV is adopted mainly in Korea,
Japan, the US, and Canada.
PAL TV - PAL TV is adopted mainly in Europe.
SUBTITLE
DISC MENU
PREFERED SUBTITLE LANGUAGE
PREFERED MENU LANGUAGE
LOCALE
PARENTAL
PARENTAL LOCALITY CODE - You can select a
locality code. Make sure to select a code suitable
for the locality code of the disc to play.
SET PARENTAL LEVEL - You can set up "Parental
Level" in 8 levels so that children couldn't watch
such programs as are too violent or only for adults.
PASSWORD
DEFAULTS
CHANGE PASSWORD - You can change
password.
LOAD FACTORY SETTING - You can set up the
setup menu to its defaults.
If you forgot the password, you can input the
numbers, “5700”.
-28-
REFERENCE
Troubleshooting Guide
Check the following guide for the possible cause of a problem before contacting service.
Symptom
Cause
Correction
Plug the power cord into the battery outlet securely.
No Power
The power cord is disconnected.
No disc is inserted.
Insert a disc. (Check that the DVD or audio CD
indicator in the display is lit.)
The power is on, but the
player does not work.
Select the appropriate video input mode on the TV so
the picture from the player appears on the TV screen.
The TV is not set to receive DVD signal
output.
No picture.
Connect the video cable into the jacks.
Turn on the TV.
The video cable is not connected
securely.
The connected TV power is turned off.
Select the correct input mode of the audio receiver so
you can listen to the sound from the player.
The equipment connected with the
audio cable is not set to receive DVD
signal output.
No sound.
Connect the audio cable into the jacks securely.
The audio cables are not connected
securely.
The power of the equipment connected
with the audio cable is turned off.
Turn on the equipment connected with the audio cable.
Set the Digital Audio Output to the correct position, then
turn on the player again by pressing the POWER button.
The Digital Audio Output is set to the
wrong position.
Clean the disc.
The playback picture is poor.
The player does
The disc is dirty.
Insert a disc.(Check that the DVD, or audio CD indicator
in the display is lit.)
No disc is inserted.
not start playback.
Insert a playable disc.(Check the disc type, color system
and Regional code.)
An unplayable disc is inserted.
Place the disc with the playback side down.
Place the disc on the disc tray correctly inside the guide.
Clean the disc.
The disc is placed upside down.
The disc is not placed within the guide.
The disc is dirty.
A menu is on the TV screen.
The Parental level is set.
Press the SETUP button to turn off the menu screen.
Cancel the Parental function or change the parental
level.
The Remote control does
not work properly
The remote control is not pointed at the remote Point the remote control at the remote sensor of the
player.
sensor of the player.
The remote control is too far from theplayer. Operate the remote control within about 5m.
Remove the obstacle.
There is an obstacle in the path of the
remote control and the player.
The batteries in the remote control are
exhausted.
Replace the batteries with new ones.
The POWER button and
the other buttons are not
operated.
The buttons or screen holding
error may occur by some discs.
In this case unplug the power cord of the player,
and then plug in the power cord again.
-29-
REFERENCE
Specifications
Power Source
DC 12V
12W
Power Consumption
Weight
1.4 kg
Dimensions(Widthx Height x Depth)
Signal System
178mm (W) x 51mm (H) x 217mm (D)
NTSC/PAL
Frequency Response
20 Hz - 20 kHz
2.0 V(rms)
Audio
Video
Output level (Analog)
S/N Ratio
90 dB(1kHz JIS-A Filter)
1.0 Vp-p / 75Ω
5℃ ~ 35℃
Output level
Temperature
Humidity
30% ~ 60%
Environment
Condition
Horizontally
Remote control ……………………………1
Battery (AAA) ………………………………2
Power Cable ………………………………1
External remote receiver …………………1
A/V Cable……………………………………1
Accessories supplied
* Designs and speccifications are subject to change without notice for improvement.
-30-
|