Breville is a registered trademark of Breville Pty. Ltd.
ABN 98 000 092 928
Breville Customer Service Centre
Australian Customers
Café Modena
Espresso/Cappuccino Machine
Breville Customer Service Centre
PO Box 22
Instructions
BES230
Botany NSW 2019
AUSTRALIA
Customer Service: 1300 139 798
Fax (02) 9384 9601
New Zealand Customers
Breville Customer Service Centre
Private Bag 94411
Greenmount
Auckland, New Zealand
Customer Service: 0800 273 845
Fax 0800 288 513
© Copyright. Breville Pty. Ltd. 2008
Due to continual improvements in design or otherwise,
the product you purchase may differ slightly from the one
illustrated in this booklet.
Model: BES230 Issue 1/08
BES230_CAFE MODENA_FA.indd 1-1
10/6/08 3:04:10 PM
Breville recommends safety first continued
Breville recommends safety first
We at Breville are very safety conscious. We design and manufacture consumer products with the safety of you,
our valued customer foremost in mind. In addition we ask that you exercise a degree of care when using any
electrical appliance and adhere to the following precautions:
ImportANt SAfeguArdS for your BrevIlle CAfé modeNA
eSpreSSo/CAppuCCINo mACHINe
ImportANt SAfeguArdS for All eleCtrICAl ApplIANCeS
• Carefully read all instructions before operating and
save for future reference.
• Always ensure the selector control has been turned
to the ‘STANDBy’ position, the Power ‘ON/OFF’
switch has been pressed to the ‘OFF’ position and
the Breville Café Modena Espresso/Cappuccino
Machine is switched off at the power outlet and
unplugged when not in use, before cleaning, before
attempting to move the appliance, disassembling,
assembling and when storing the appliance.
• Unwind the power cord before use.
• Any maintenance, other than cleaning, should be
performed at an authorised Breville Service Centre.
• To protect against electric shock, do not immerse
power cord, power plug or appliance in water or
any other liquid.
• Remove and safely discard any packaging material
and promotional labels before using the Breville
Café Modena Espresso/Cappuccino Machine for the
first time.
• This appliance is for household use only. Do not use
this appliance for anything other than its intended
use. Do not use moving vehicles or boats. Do not
use outdoors. Misuse may cause injury.
• Do not let the power cord hang over the edge of
a bench or table, touch hot surfaces or become
knotted.
• To eliminate a choking hazard for young children,
remove and safely discard the protective cover
that is fitted to the power plug of the Breville Café
Modena Espresso/Cappuccino Machine.
• The installation of a residual current device (safety
switch) is recommended to provide additional
safety protection when using electrical appliances.
It is advisable that a safety switch with a rated
residual operating current not exceeding 30mA
be installed in the electrical circuit supplying the
appliance. See your electrician for professional
advice.
• This appliance is not intended for use by persons
(including children) with reduced physical, sensory
or mental capabilities, or lack of experience
and knowledge, unless they have been given
supervision or instruction concerning use of the
appliance by a person responsible for their safety.
• Do not attempt to operate the Breville Café Modena
Espresso/Cappuccino Machine by any method
other than those described in this booklet.
• Do not place the Breville Café Modena Espresso/
Cappuccino Machine near the edge of a bench or
table during operation. Ensure the surface is level,
clean and free of water and other substances.
• Use only cold tap water in the water tank. Do not
use any other liquid.
• Never use the Breville Café Modena Espresso/
Cappuccino Machine without water in the water
tank.
• Children should be supervised to ensure that they
do not play with the appliance.
• Do not place the Breville Café Modena Espresso/
Cappuccino Machine on or near a hot gas or
electric burner, or where it could touch a heated
oven.
• It is recommended to regularly inspect the
appliance. Do not use the appliance if power
supply cord, power plug or appliance becomes
damaged in any way. Return the entire appliance
to the nearest authorised Breville service centre for
examination and/or repair.
• Ensure the filter holder is firmly inserted and
secured into the brewing head before using the
machine.
• Always ensure the Breville Café Modena Espresso/
Cappuccino Machine is properly assembled before
connecting to power outlet and operating. Follow
the instructions provided in this booklet.
• Never remove the filter holder during the brewing
operation as the machine is under pressure.
• Do not touch hot surfaces. Allow the Breville Café
Modena Espresso/Cappuccino Machine to cool
down before moving or cleaning any parts.
• The appliance is not intended to be operated by
means of an external timer or separate remote
control system.
• Do not move the Breville Café Modena Espresso/
Cappuccino Machine whilst in operation.
• Do not use the Breville Café Modena Espresso/
Cappuccino Machine on a sink drain board.
• Do not leave the Breville Café Modena Espresso/
Cappuccino Machine unattended when in use.
• Do not use attachments other than those
provided with the Breville Café Modena Espresso/
Cappuccino Machine.
• Keep the appliance and accessories clean. Follow
the cleaning instructions provided in this book
(page 12).
• Do not place anything, other than cups for
warming, on top of the Breville Café Modena
Espresso/Cappuccino Machine.
DO NOT IMMERSE ANY PART OF YOUR BREVILLE CAFé MODENA ESPRESSO/
CAPPUCCINO MACHINE IN WATER OR ANY OTHER LIQUID.
4
5
BES230_CAFE MODENA_FA.indd 4-5
10/6/08 3:04:11 PM
operating your Breville Café modena
espresso/Cappuccino machine
Know your Breville Café modena
espresso/Cappuccino machine
Power ‘ON/OFF’ switch
Cup warming plate
Before first use
The water tank should be filled with fresh
cold water before use.
• Remove and safely discard any packaging material
or promotional labels before using your Breville
Café Modena Espresso/Cappuccino Machine for the
first time.
Removable 1.2 litre water tank
‘POWER’ light (red)
Check water level before use and replace
the water daily.
illuminates when the
machine is turned on
Do not used mineral or distilled water.
• It is recommended to wash the frothing jug,
measuring spoon, filter holder and the stainless
steel filters in mild detergent and water. Rinse and
dry thoroughly.
15 bar Italian designed & made pump system
Note
pre-heating the machine
• Wipe the outer housing with a soft, damp cloth and
dry thoroughly. Do not immerse the outer housing,
power cord or power plug in water or any other
liquid.
For optimal crema, it is recommended to carry out a
complete brewing operation with water but without
any ground coffee in the filter holder before making
your first coffee to ensure that the machine has
been pre-heated.
‘HEATING’ light (orange)
Thermoblock heating system
illuminates to indicate that
the machine is heating and
will turn off when the correct
temperature has been reached.
This light will cycle on and off
during operation to indicate the
machine is monitoring the correct
temperature
Selector control
for Espresso and Steam
Do not clean any of the parts or accessories
in the dishwasher.
• Ensure the Selector Control is in the ‘STANDBy’
position.
Brew head
Note
• Insert the power plug into a 230/240V outlet and
switch on. Press the Power ‘ON/OFF’ switch to
‘ON’.
Filter holder
External water window
filling the water tank
• When the orange ‘HEATING’ light goes off, turn the
2 stainless steel filters
• Ensure that the Power ‘ON/OFF’ switch is in the
‘OFF’ position and the Selector Control is in the
‘STANDBy’ position.
Swivel steam wand
with froth enhancer
Selector Control to the
’ESPRESSO’ position
(1 cup filter and 2 cup filter)
and allow a small amount of water to run through
the brew head for a few seconds without the filter
holder in place.
• Switch the machine off at the power outlet and
unplug the power cord.
Steam baffle
Crema is the finely-aerated, golden,
aromatic layer, extracted from the ground
coffee during brewing, that settles on top of
the brewed coffee.
• Open the water tank lid and remove the water tank.
Fill the water tank with cold water to the maximum
mark and replace back into the machine, pressing
down firmly so that the water valve opens. Close
the water tank lid.
Note
pre-warming cups
For optimal coffee temperature, pre-warm cups by
placing them on the cup warming plate.
Removable drip tray
and grid
Combined measuring spoon
and coffee press
Water level indicator
ꢀ
6
ꢁ
7
BES230_CAFE MODENA_FA.indd 6-7
10/6/08 3:04:12 PM
operating your Breville Café modena
operating your Breville Café modena
continued
continued
espresso/Cappuccino machine
espresso/Cappuccino machine
• Clean any excess ground coffee from the rim of the
filter holder to ensure a proper fit under the brew
head.
preparing the coffee
Brewing the coffee
The Breville Café Modena Espresso/
Cappuccino Machine remains ready for
brewing and maintains a constant heating
temperature whilst the Power ‘ON/OFF’
switch remains in the ‘ON’ position. If
the temperature decreases, the orange
‘HEATING’ light will illuminate and the
heater will automatically heat to maintain
the correct brewing temperature.
• Place the 1 or 2 cup filter into the filter holder and
fill with ground coffee (use the smaller filter for 1
cup and the larger filter for 2 cups).
• Ensure the Selector Control is in the ‘STANDBy’
position.
• Place the filter retainer clip in the release position,
by pulling the clip back towards your hand.
• Insert the power plug into a 230/240V power outlet
and switch on.
• Use 1 level measure of ground coffee for the
1 cup filter and 2 level measures for the 2 cup
filter. It is important to use the correct amount of
ground coffee as the filter perforations have been
constructed for optimal pressure build up in
the machine.
• Press the Power ‘ON/OFF’ switch to ‘ON’. The red
‘POWER’ light and the orange ‘HEATING’ light will
illuminate. The orange ‘HEATING’ light goes off
when the machine is heated.
Note
• Ensure the drip tray is in place.
• Position one or two pre-heated cups beneath the
filter holder.
How to froth milk for a cappuccino or
latte
• Place the filer holder underneath the brew head so
that the handle is positioned to the left of centre.
Lift the filter holder until it contacts the brew head
and rotate to the right.
• Turn the Selector Control to the
position.
‘ESPRESSO’
The Breville Café Modena Espresso/Cappuccino
Machine comes complete with a steam wand for
easier steaming and frothing of milk. The first step in
making a cappuccino/latte is to make a short espresso
(see ‘Brewing the coffee’). Then:
• After a few seconds, aromatic coffee will begin
to run through the filter holder.
• When sufficient coffee has flowed into the cups,
turn the Selector Control to the ‘STANDBy’ position.
This will stop the flow of coffee.
• Fill the stainless steel frothing jug 1⁄
full with
3
cold milk.
• If the ‘STEAM’ function is not required, press the
Power ‘ON/OFF’ switch to ‘OFF’, switch off at the
power outlet, unplug the power cord and allow the
machine to cool.
• When the orange ‘HEATING’ light goes off, insert
the steam wand, with the froth enhancer attached,
into jug of milk so that the head of the froth
enhancer is just immersed into the milk.
• Distribute the ground coffee evenly in the filter
and tamp (press) lightly with the bottom of the
measuring spoon (if there is too much ground
coffee or too firmly tamped, the flow of water can
be blocked).
• Remove the filter holder from the brew head and
using the filter retainer clip to secure the filter in
the filter holder, turn the filter holder upside down
to empty the used coffee into a bin. Used coffee
grounds should be thrown away with domestic
waste and not down the sink which may block
drains. Rinse the filter and filter holder with water
and allow to dry.
THE METAL PARTS OF THE FILTER HOLDER MAY STILL BE VERY HOT. COOL THESE
PARTS UNDER COLD WATER. ENSURE THE FILTER RETAINER CLIP IS USED TO SECURE
FILTER WHEN DISCARDING THE COFFEE GROUNDS.
8
9
BES230_CAFE MODENA_FA.indd 8-9
10/6/08 3:04:14 PM
operating your Breville Café modena
Coffee making tips
continued
espresso/Cappuccino machine
tips on making the perfect espresso
the grind
• Turn the selector control to the
position.
‘STEAM’
Always ensure that the froth enhancer has
been firmly inserted onto the steam wand.
For best results use fresh cold milk (lite
milk will froth easier).
Always clean the steam wand and froth
enhancer after each use (refer to Care and
cleaning on Page 12).
Use the steam wand without the froth
enhancer if steamed milk without the froth
is required.
Don’t just rely on your coffee machine to do all the
work. Making a good cup of coffee is an art.
• If using pre-ground coffee, purchase an espresso
grind suitable for espresso/cappuccino machines.
• Gently move the frothing jug in a circular motion
around the froth enhancer to steam the milk.
• If grinding coffee, select a fine grind setting
suitable for espresso coffee.
Water flow
• When the milk begins to increase in volume,
immerse the froth enhancer deeper into the milk to
further froth the milk, if required.
If you’re making an espresso, make sure the water
flows through the coffee filter at the correct rate. If
it’s too slow, the coffee will be over-extracted – too
dark and bitter, with a mottled and uneven crema on
top. If it flows too quickly, the coffee will be under-
extracted – the proper flavour will not have had
time to develop. Adjust the water flow by tamping
(pressing down) the ground coffee firmly or by
changing the grind of the coffee.
• If the grind is too fine, the water will not flow
through the coffee even under pressure (this grind
looks like powder and feels like flour when rubbed
between fingers).
• To avoid over-heating or burning the milk, place
your hand on the bottom of the stainless frothing
jug. When the jug becomes almost too hot to touch,
turn the selector control to the ‘STANDBy’ position
to stop the steaming function before removing the
jug.
If brewing more coffee immediately
after using the ‘STEAM’ function, turn
• If the grind is too coarse, the water flows
through the coffee too fast, preventing a full
flavoured extraction.
the Selector Control to the
‘ESPRESSO’
position and allow a small amount of water
to run through the brew head for a few
seconds without the filter holder in place.
This will prepare the machine for optimal
brewing temperature.
When steaming milk a pumping should will
be heard. This is the pump operating and is
normal.
As the Selector Control is turned to the
‘STANDBY’ position, steam will be released
from the machine. This is normal operation.
the coffee
• Pre-ground coffee will only retain its flavour for
1 week, provided it is stored in an air tight
container, in a cool, dark area.
Note
• Whole coffee beans are recommended and should
be ground just before use.
Note
• Coffee beans stored in an airtight container will
keep up to 1 month before they begin to lose their
flavour.
• Carefully pour the steamed milk into each cup
of freshly brewed espresso coffee and spoon the
frothed milk on top in the following ratios:
1
• Do not store coffee or beans in a refrigerator or
freezer.
Cappuccino – ⁄
3
espresso, 1⁄
frothed milk
espresso topped with steamed
3
steamed milk,
1
⁄
3
1
Latte –
⁄
3
milk and about 10cm of frothed
milk (traditionally served in a glass)
WHEN FROTHING, MILK SHOULD NOT BE ALLOWED TO RUN OVER THE TOP OF THE
FROTH ENHANCER, OTHERWISE IT WILL NOT FUNCTION PROPERLY.
TO AVOID SPLATTERING OF HOT MILK, DO NOT MOVE THE STEAM WAND OR FROTH
ENHANCER ABOVE THE SURFACE OF THE MILK WHILE STEAMING OR FROTHING.
WHEN STEAMING OR FROTHING MILK, ENSURE THE SELECTOR CONTROL IS IN THE
‘STANDBY’ POSITION BEFORE REMOVING THE FROTHING JUG.
10
11
BES230_CAFE MODENA_FA.indd 10-11
10/6/08 3:04:15 PM
continued
Care and cleaning
Care and cleaning
Before cleaning, ensure the Selector Control is in the
‘STANDBy’ position and press the Power ‘ON/OFF’
switch to ‘OFF’. Switch off at the power outlet, then
unplug the power cord and allow the coffee machine
to cool completely before cleaning.
Cleaning the drip tray
decalcifying the machine
• The drip tray should be removed, emptied and
cleaned at regular intervals, particularly when the
water level indicator shows that the drip tray is full.
• Ensure the Selector Control is in the ‘STANDBy’
position and the Power ‘ON/OFF’ switch is pressed
to ‘OFF’. Switch off at the power outlet and unplug
the power cord.
• Remove the grid, steam baffle and water level
indicator from the drip tray, wash all 4 parts with
water and non-abrasive washing liquid before
rinsing and drying.
• Remove the filter holder and pour the prepared
decalcifying solution into the water tank.
Cleaning the steam wand & froth
enhancer
• Insert the power cord at the outlet and switch on.
• Press the Power ‘ON/OFF’ switch to the ‘ON’.
• The steam wand and froth enhancer should always
be cleaned after steaming or frothing milk.
Do not place any parts of the Espresso/
Cappuccino machine in the dishwasher.
• Remove the froth enhancer and rinse under warm
tap water.
• Place a suitably large container under both the
brew head and the steam wand.
Cleaning the filters, filter holder
Note
• When the brewing temperature is reached the
orange ‘HEATING’ light will go off.
and brew head
• Immediately after use, remove the filter holder and
discard the used ground coffee. Rinse the stainless
steel filters and filter holder under hot running
water. Should the fine holes in the filters become
blocked, then a clean, plastic dishwashing
brush should be used (do not use a brush with
metal bristles).
decalcifying
• Turn the Selector Control to the
position and allow half the decalcifying solution to
run through the brew head.
‘ESPRESSO’
After regular use, hard water can cause limestone
build up in, and on, many of the inner functioning
components, reducing the brewing flow, power
of the machine, and affecting the quality of coffee.
• Turn the Selector Control to the
‘STEAM’
position and allow the remaining solution run
through the steam wand. Then turn the Selector
Control to the ‘STANDBy’ position.
We advise decalcifying the machine on a regular
basis (every 2-3 months) using a mixture of white
vinegar and water. Use the following as a guide:
• The brew head area should be wiped with a damp
cloth to remove any remaining used ground coffee.
• After decalcifying, re-fill the water tank with fresh
cold water and rinse the machine by following the
instructions for decalcifying and running half the
water through the brew head and half through the
steam wand.
diluted solution (for softer water)
• 1 part white vinegar
• It is advisable to periodically run water through
the coffee machine with an empty filter and filter
holder in place to remove any used ground coffee.
• Wipe the steam wand with a damp cloth.
• Place a clean jug or cup under the steam wand
then turn the Selector Control briefly to the
‘STEAM’ position to clear any remaining milk
from the steam wand.
• 2 parts cold tap water
Cleaning the housing/cup warming tray
• The machine is now ready for use.
Concentrated solution (for harder water)
• 1 part white vinegar
• The outer housing can be wiped with a soft, damp
cloth (do not use abrasive agents or cloths which
can scratch the surfaces), then polished and dried
with a soft, dry cloth.
• If the fine opening of the steam wand becomes
blocked, allow the machine to cool and use a
needle or fine sharp implement to unblock the
opening.
The stainless steel filters should not come
in contact with any decalcifying agents.
• 1 part cold tap water
Do not use commercial powder or liquid
decalcifying agents.
Note
THE WATER TANK SHOULD NEVER BE REMOVED OR COMPLETELY EMPTIED DURING
DECALCIFYING.
DO NOT IMMERSE ANY PART OF YOUR BREVILLE CAFé MODENA ESPRESSO/
CAPPUCCINO MACHINE IN WATER OR ANY OTHER LIQUID.
12
13
BES230_CAFE MODENA_FA.indd 12-13
10/6/08 3:04:17 PM
trouble shooting chart
Coffees to try
espresso
proBlem
poSSIBle CAuSeS
Intense and aromatic, an espresso, or short
black as it’s also known, uses about 7g of
ground coffee. It is served in a small cup or
glass to a level of approximately 35mm.
Coffee does not run through • Machine is not turned on or plugged in
• Water tank is empty
• Selector Control not in
‘ESPRESSO’ position
• Coffee grind is too fine
Cappuccino
• Too much coffee in the filter and/or too firmly tamped (pressed)
• The filter is blocked (see Care and cleaning)
A cappuccino is very light and almost luke
warm. It has one-third espresso, one-third milk
and one-third foam. It is traditionally consumed
before noon.
Coffee runs out too quickly
Coffee runs too slowly
• Coffee grind is too coarse
• Not enough coffee in the filter and/or too firmly tamped (pressed)
• The water tank is empty or low
• Coffee grind is too fine
• Machine is blocked by scale build up (see Care and cleaning)
Café latte
Served in a glass, a café latte consists of one-
third espresso, topped with steamed milk and
about 10mm of foam.
Brewed coffee runs out
around the edge of the
filter holder
• Filter holder is not inserted in the brew head correctly
• There are coffee grounds around the filter rim
• Too much coffee in the filter
• Coffee has been too firmly tamped (pressed)
macchiato
the machine is too loud
• Water tank is empty
Traditionally served short, the macchiato is also
poured as a long black with a dash of milk or a
dollop of foam.
• Water tank is not securely in place
Coffee is too weak or watery • Coffee grind is not fine enough
(use coffee grind suitable for espresso machines)
Coffee is too cold
• Machine not pre-heated
long black
• Cups not pre-heated
• Milk not heated enough (if making a cappuccino or latte)
A long black is generally served as a double
shot of espresso.
No crema
• Coffee is not tamped (pressed) firmly enough
• Coffee grind is too coarse
• Coffee is not fresh
No steam is generated
• Machine is not turned on
• Water tank is empty
ristretto
Meaning restricted, a ristretto is an
extremely short espresso of approximately
15mm, distinguished by its intense flavour
and aftertaste.
• Selector Control not in
• Swivel steam wand is blocked (see Care and cleaning)
‘STEAM’ position
milk is not foamy
after frothing
• Not enough steam
• Milk is not fresh and cold
14
15
BES230_CAFE MODENA_FA.indd 14-15
10/6/08 3:04:18 PM
|